null - Gardif
Contents
1. HEDGE TRIMMER ATTACHMENT to LK 2813446 AUTO MULTITOOLS BRUSH CUTTER Model PBT3446TP Translation of the original instructions for use WARNING Read the instructions before using the product Before initial start up please read through these operating instructions carefully prior to using the machine Keep the instructions safe and pass them on to any subsequent user so that the information is always available Serial Number pt A ate HEDGE TRIMMER INSTRUCTIONS MANUAL This hedge trimmer attachment can ONLY be fitted on brush cutter model LK PBT3446 MULTITOOLS and used with it A2 Before use all users must carefully read this maintenance and user manual and fully familiarize themselves with all controls to ensure the correct operation of the hedge trimmer A2 1 Keep this manual in a safe place for future reference A3 Do not allow children under 16 and people who have not read this user manual to use the product A4 Do not start and use the hedge trimmer near people animals or objects During operation a minimum distance of 5 m between the machine and other people should be kept A5 Special attention should be paid to possible dangers that may not be heard because of the noise made by the hedge trimmer A6 Make sure there are no dangerous objects such as cables and electric cables in the working area A7 The operator is resp2. PBT3446 AUTO MULTITOOLS CHECKING THE SCREWS AND MOVING PARTS Before each use check that there are no loose screws or parts and that the cutting device has no cracks or is excessively worn Replace any damaged parts before use BLADES If a reduction in cutting performance and efficiency of the hedge trimmer is experienced the blades need to be sharpened THIS OPERATION SHOULD BE CARRIED OUT BY A SPECIALISED SERVICE CENTRE Do not use the hedge trimmer if the blades are worn or damaged in order to avoid damages and possible personal injury CLEANING Periodically Clean the blades check their conditions and do maintenance as spray with lubricants and tree sap repellent protect using the blade guard fig 12 7 OPERATION HOW TO USE THE HEDGE TRIMMER 1 Hook the belt sling fig 11 item 1 onto the ring fig 11 item 2 2 Hold the hedge trimmer on the right side as shown in fig 11 see Brush Cutter user manual DURING OPERATION A Ifa dangerous condition occurs immediately switch off the engine by pressing the switch to the OFF position N This product is not electrically isolated Make sure there are no IN electric cables or high voltage IN _ cables in the working area DANGER OF ELECTRIC SHOCK Always hold the hedge trimmer with both hands Operate it by fully depressing the throttle lever PREPARATION Remove dry branches twigs or any other material thet could obst
3. in compliance with standards EN 292 and EN 774 HT attachment LK PBT3446 AUTO Made in Ponthierry France 2013 12 11 B VAN ELSLANDE Managing Director Sil
4. itions apply engine speed to idle and stop the blades STARTING THE ENGINE WARNING DANGER If the blades 1 Position the hedge trimmer in a safe do not stop when the engine starting position reaches idle speed contact a 2 Position the cutting blades at an ange Service center fig 7 3 Remove the blade guards The blades STOPPING THE ENGINE must not touch the ground or any other object if possible rest the reduction unit on a raised surface such as on raised ground a brick or a log 4 Get into a stable position 5 With the left hand push hard the equipment on the ground 1 To stop the engine move the switch fig 17 item 1 to the OFF position 6 Do not rest the foot or the knee onto the shaft 7 Start the engine as shown in the Brush Cutter manual fig 16 WARNING The cutting device will continue to move for some time after having switched off the product switch to the OFF position Firmly hold the two handles until the cutting device comes to a complete stop A WARNING Familiarize yourself with the on off switch in order to react promptly in case of emergency HEDGE TRIMMER INSTRUCTIONS MANUAL HIGH HORIZONTAL CUT or hedge top adjust the hedge trimmer operating angle as shown in fig 15 to cut the top of a high hedge 9 MAINTENANCE AND TRANSPORT For maintenance operations relating to the engine see the enclosed Brushcutter manual LK
5. mmended The hedge trimmer is used continuously for long periods of time intermittent use is recommended If you feel a tingling sensation or numbness seek medical attention B8 1 Always hold the hedge trimmer with both hands Stand in a safe and steady position on both legs Keep your balance Do not operate on unstable stairs To cut high hedges use a stable scaffolding 88 2 This product is designed to be used on the right hand side of the operator see fig 11 Hold the rear handle fitted with controls with your right hand and the front handle with your left hand B9 WARNING Petrol and its vapours are highly flammable BURNING AND FIRE HAZARDS B9 1 Stop the engine before refuelling B9 2 Do not smoke while refuelling B9 3 Wipe off any spilled fuel Start the engine away from the refuelling area 89 4 Make sure the tank cap is firmly tightened Beware of any leaks A8 Do not touch the blades when the engine is on Switch the engine off before touching the blades even when you have to remove branches WARNING DANGER THE CUTTING BLADES CAN CAUSE VERY SERIOUS INJURIES OPERATION B1 Use the hedge trimmer only to cut hedge weeds and bushes Do not use the hedge trimmer for other purposes B2 Wear safety clothing and safety equipment During operation do not wear loose or baggy clothing B3 Wear approved protective goggles or visor B3 1 Wear app
6. onsible for any accidents or dangers involving other people or their belongings DANGER Thank you for choosing one of our garden products This hedge trimmer attachment has been manufactured in accordance with current safety regulations in order to protect the consumer This manual describes and illustrates the assembly use and maintenance operations required to keep your hedge trimmer attachment in safe condition USEFUL PICTURES The pictures relating to the assembly operations and the machine description can be found at the beginning of this user manual Keep these pages open while reading the assembly instructions Should your hedge trimmer attachment need servicing or repair please contact your retailer or an approved service center 1 ESSENTIAL SAFETY MEASURES GENERAL SAFETY INSTRUCTIONS CAUTIONS A1 Failure to comply with safety measures and safety instructions when using the hedge trimmer can cause serious injuries A THIS MANUAL MUST ALWAYS BE READ TOGETHER WITH THE BRUSH CUTTER MANUAL IT IS DESIGNED TO BE FITTED ON fig 5 HEDGE TRIMMER INSTRUCTIONS MANUAL B8 Prolonged use of the hedge trimmer may hinder blood circulation to the hands Raynaud s disease due to vibrations The following factors may present a risk to the operator s health Operator has poor circulation to his hands The hedge trimmer is used in cold weather wearing warm gloves is strongly reco
7. ration of the throttle control lever B10 2 Engine power ON OFF SWITCH refer to Brushcutter manual DANGER The cutting device continues to spin for a while even after the on off switch has been turned to the OFF position Hold both handles firmly until the cutting device has come to a com plete stop See section STARTING AND STOPPING 3 DESCRIPTION OF MACHINE PARTS picture 1 1 Shaft 2 3 Gearbox 4 5 Cutting blades 6 Blade holder bar 7 Shaft clamp locking screw 8 Shaft centring screw 9 Blade guards 10 Tilting handle 11 Tilting selector switch lockout knob 12 Tilting angle selector switch HEDGE TRIMMER INSTRUCTIONS MANUAL WORKING ANGLE ADJUSTMENT The blades may be adjusted in 8 different positions up fig 7 and down fig 8 WARNING The working angle adjustment operation must be carried out only when the blades have come to a complete stop engine off gt WARNING When the hedge trimmer is in operation the reduction unit will heat up Do not touch the box without safety gloves 4 uhm Danger of burns 1 Slacken the tilting selector switch lockout knob fig 9 item 1 2 Tilt the blades in the desired position fig 10 3 Tighten the knob BELT HOOK AND FIXING RING Fig 11 refer to the Brushcutter manual The same conditions apply 9 REFUELLING pls refer to the Brushcutter manual f I 1 Slacken the knob 3 on the clamp 1 loca
8. roved ear protectors B3 2 Wear a safety helmet in areas where objects are likely to fall B4 Wear sturdy shoes with non slip soles B5 Wear sturdy gloves B6 The operator must be in good physical condition DO NOT USE the product if you feel tired ill or are under the influence of alcohol medicines or drugs 87 WARNING Exhaust fumes are toxic and asphyxiating If inhaled these fumes could be lethal Do not start the engine in enclosed or poorly ventilated areas HEDGE TRIMMER INSTRUCTIONS MANUAL 4 ASSEMBLY 1 The packaging box contains the gearbox and the blades separated from the shaft see fig 2 FITTING THE BLADE UNIT ONTO THE SHAFT 1 Fit the hedge trimmer fig 3 item 1 onto the bottom drive shaft fig 3 item 2 making sure that the drive spindle fig 3 item 3 is correctly located inside the gearbox housing WARNING The locating hole fig 3 item A on the shaft must match the position of the gearbox hole fig 3 item B 2 Firstly fit and tighten the screw fig 4 item 1 then firmly tighten the clamp fig 4 item 2 FITTING THE WHOLE HEDGE TRIMMER UNIT ONTO THE MOTORISED UNIT WARNING The hedge trimmer can be A fitted in 3 different positions matching the 3 holes located in the top shaft clamp fig 6 A 0 fig 7 C 180 fig 8 POSITION A B10 SAFETY DEVICES B10 1 The THROTTLE TRIGGER LOCKOUT refer to Brushcutter manual stops accidental ope
9. ructs the cutting operation VERTICAL CUT Carry out fitting A 0 or B 90 fig 7 then adjust the blade angle as required see fig 13 LOW HORIZONTAL CUT Carry out fitting A 0 fig 7 then adjust the blade angle as required see fig 14 HIGH HORIZONTAL CUT Carry out fitting C 180 fig 8 then adjust the blade angle as required see fig 15 12 HEDGE TRIMMER OPERATING MANUAL A TRANSPORT During transport even for short distances the blade guards must be fitted pict 12 m ALWAYS USE GLOVES WHEN FITTING OR REMOVING THE BLADE GUARDS gt STORAGE Clean the hedge trimmer If the trimmer is not used for over 2 months empty the fuel tank Do not clean with aggressive detergents Keep the hedge trimmer in a dry and safe place inaccessible to children HEDGE TRIMMER INSTRUCTIONS MANUAL Sound power level SWL av ISO 11094 108 dB A Hedge trimmer attachment weight 7 Hedge trimmer brushcutter OTRS 7 7 m s LK PBT3446 AUTO weight No Incertitude value of 2 Sound pressure level Er 3 1 m s SPL av EN ISO 11201 88 dB A vibration CE EC DECLARATION OF CONFORMITY The undersigned declares that the following product HEDGE TRIMMER attachment when fitted to the motorised units LK PBT3446 AUTO MULTITOOLS complies with directives 98 37 EEC 2000 14 EEC enclosure V according to standard ISO 11094 and has been developed
10. ted on the motorized unit 2 Move closer and introduce the shaft 2 in the clamp making sure the flexible peg 5 matches the hole 4 Push fully down until the flexible peg comes out of the hole see stage 6 Fully tighten the screw knob as shown in the picture This fitting position A 0 is suitable for usage shown in figures 13 14 Also see fitting position B 90 suitable for usage shown in Fig 13 POSITION C 1 Slacken the knob 3 on the clamp 1 located on the motorized unit 2 Move closer and introduce the shaft 2 in the clamp making sure the flexible peg 5 matches the hole 4 Push fully down until the flexible peg comes out of the hole see stage 6 Fully tighten the screw knob as shown in the picture This fitting position C 180 is suitable for usage shown in fig 15 WARNING Start the engine only after AN connecting the bottom drive shaft to the upper drive shaft Make sure the clamp screw knob fig 6 item 1 is firmly tightened HEDGE TRIMMER INSTRUCTIONS MANUAL 6 STARTING AND STOPPING WARNING DANGER If the engine A starts and stays in the half WARNING Do not start the engine acceleration position the blades are A without first fitting the hedge moving Let the engine turn for a trimmer correctly see paragraph 4 few seconds to make sure it warms up Assembly pls refer to Brush Cutter Operate the trigger once to reduce the manual The same cond
Download Pdf Manuals
Related Search