Bushnell 119445 Digital Camera User Manual
Contents
1. Fig 23 Fig 24 Distance 3 28 N 34 05327 w118 24504 ZS Loc Safe rack Exit Option Left Arrow or 2 Sec Hold 18 The HOT Button cont SafeTrack Mode The remaining HOT button menu items are My Routes Fig 9 same 3 options as listed above for Trails a Route is the most direct or shortest path between two points routes are more often used for water based navigation due to the reduced number of natural obstacles whereas trails are more useful on land My Photos you have the options here to navigate towards a stored satellite photo Fig 20 or topo map and to manage them photos amp maps are downloaded not user created SafeTrack Battery Conservation Mode SafeTrack mode should be set whenever you are using your GPS extending your battery life without the wait to re establish satellite contact you would have after a full power off SafeTrack mode can be started in either of two ways The first way 15 to hold the hot button for 2 seconds make sure you have exited any page menu first The SafeTrack Selected screen will be displayed Fig 21 the unit will automatically go into SafeTrack and the red indicator light at the top center of the ONIX will come on as you enter SafeTrack then change to blinking green The second way to enter SafeTrack mode is by selecting SafeTrack from the hot button menu as shown on page 16 Fig 14 Arrow down to Sta2. The Four Main Pages Overview 3 The NAV Navigation Page The NAV page provides a standard compass display with arrows to indicate your last heading and or current bearing along with magnetic or true north indication and other optional navigation related data depending on the display preferences the user has set up This page is especially useful if you do not choose to see a compass image layered on top of the MAP page you may switch over to it at any time then return to MAP page just as you left it Note that the compass readings are based on your position relative to the GPS satellites and can therefore only show your direction when you are moving unlike magnetic compasses 4 The SET Set Up Page The SET page is used to personalize how the Onix displays information to suit your needs and preferences Many of the items on the SET menu are options you may set once when you first turn on your ONIX even before you begin using it to navigate and will probably leave on that setting for the rest of the time you use your GPS The other pages have their own set of menus that allow you to select options that affect what types of information are displayed change their appearance and recall or delete previously stored map points photos etc heading Altitude 2409 5 Ft 4 046052 i Loc wM48 22420 COMPASS Time ES anguage Ouner Info attery Selection i 7 Unit Info 4 SET Page Full Menu Pres
3. Speed Heading Bearing Arrow Active Navigation 12 Page View Details POI points of interest from a pre programmed saved list airports hospitals etc Navigation Data Fields these sections of the map page display user selected navigation information To access and select the lower Nav data boxes fields arrow down below Point Of Interest to highlight each of the 3 available Nav data fields Press the center OK button to see the list of Nav data any 3 of the 20 types on the list can be displayed When you Select a new one it replaces a previous data display but always shows 3 at a time For each given field click OK to view the available options Note that LOC which is your global position Lat Long takes up 2 fields Latitude 15 the top field When using the position selector the ONIX will display 4 fields There are another 2 Nav data boxes at the upper left and right of the screen From the display options press the up arrow while on Compass us will highlight the upper left box Press OK to see list of available display options Make a selection and confirm it by pressing OK then use the right arrow to move over to the right Nav data box Make a selection and confirm as you did in the left box You may then use the down arrow to return to the list of display options etc Press the left arrow to exit the map layer display options 3 NAV Page View Fig 4 The NAV
4. This movement could be for a plane ship automobile person on foot or any other similar means North Up Orientation Fixes the GPS receiver s map display so north is always fixed at the top of the screen Position An exact unique location based on a geographic coordinate system Position Fix The GPS receiver s computed position coordinates Position Format The way in which the GPS receiver s position will be displayed on the screen Commonly displayed as latitude longitude in degrees and minutes with options for degrees minutes and seconds degrees only or one of several grid formats 24 Glossary Route A group of waypoints entered into the GPS receiver in the sequence you desire to navigate them Statute Mile A unit of length equal to 5 280 feet or 1 760 yards 1 609 meters used in the U S and some other English speaking countries Time To First Fix TTFF If you have not used your GPS unit for several months the almanac data for the satellites may be out of date The unit is capable of recollecting this information on its own but the process can take several minutes Time to First Fix TTFF is the time it takes a GPS receiver to find satellites after the user first turns it on when the GPS receiver has lost memory or has been moved over 300 miles from its last location Track Up Orientation Fixes the GPS receiver s map display so the current track heading is at the top of the screen Trail The actual course that
5. assume one of three shapes bearing arrow that shows your navigation A direction when you are moving or heading when you are not actively navigating C a circle you are here locator to display your current location relative to the map a crosshairs cursor that allows you to pan the check position of waypoints or POI when moved over them use as a distance measuring tool or create routes If you know the latitude longitude or other coordinates as selected in the SET menu under Units of a location you can move the crosshairs cursor on the map with the 5 way pad until the coordinates shown in the Nav data box match the location then save it as a waypoint by pressing the OK button twice Page View Details Battery Indicator shows battery condition or indicated USB power when connected to a PC Zoom Display Level scale or actual distance represented by height of current display e g 241 Meters span from top to bottom of screen Screen Layering Options User Selected You may choose to add other items to your view of the MAP page To select these items hold down the PAGE button for 2 seconds you will see a map page display options screen Fig 3 Use the 5 way button to move up and down the options press the center button to select check or deselect uncheck the items you with to include in your view Your map layer options are Compass indicates your current direction eTopo the topogra
6. has been traveled composed of a series of trail points True North The direction of the north pole from your current position Magnetic compasses indicate north differently due to the variation between true north and magnetic north A GPS receiver can display headings referenced to true north or magnetic north Universal Transverse Mercator UTM A nearly worldwide coordinate projection system using north and east distance measurements from reference point s UTM is the primary coordinate system used on U S Geological Survey topographic maps User Segment The segment of the complete GPS system that includes the GPS receiver and operator UTC See Coordinated Universal Time UTM See Universal Transverse Mercator Waterproof An IPX7 designation means the GPS case can withstand accidental immersion in one meter of water for up to 30 minutes Waypoints Waypoints are locations or landmarks worth recording and storing in your GPS These are locations you may later want to return to They may be check points on a route or significant ground features e g camp the truck a fork in a trail or a favorite fishing spot Waypoints may be defined and stored in the unit manually by taking coordinates for the waypoint from a map or other reference This can be done before ever leaving home Or more usually waypoints may be entered directly by taking a reading with the unit at the location itself giving it a name and then saving the point Waypoi
7. operation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The ONIX does not contain any user serviceable parts Repairs should only be made by an Authorized Bushnell repair center Unauthorized repairs or modifications could result in permanent damage to the equipment and will void your warranty and your authority to operate this device under Part 15 regulations The shielded interface cable which is provided must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer ONE YEA
8. section of this manual for details on entering letters and numerals Figs 25 amp 26 Battery selection choice of alkaline or rechargeable NiMh set to match the type you are using to ensure the battery indicator 15 accurate If using lithium batteries and a Lithium setting is not available on your ONIX model select the NiMh setting Unit Info provides hardware software version numbers and serial number Using Your ONIX GPS When the unit is first powered on you will see the default SAT screen It may take up to 3 or 4 minutes for the unit to scan and lock on to the GPS satellites during the first power up in a new area but will be faster when it is powered on again later in the same area See Reset Data on pg 14 if you later relocate more than 300 miles away from this initial area Once it has locked into the satellites the satellite position icons will stop blinking and go dark you are ready to begin using the ONIX The next step 15 your choice you may go to the NAV or SET page to select options or make personal settings first or begin navigating by going directly to the MAP page The simplest GPS function is to mark your present location Any location that you choose to mark 1s called a waypoint Setting a waypoint with your ONIX 15 as easy as clicking the OK key center of the 5 way switch twice The Ist click calls up the Waypoint Edit Options along with the Set Waypoint Selection Fig 12 At this
9. the battery compartment after the unit has had any prolonged exposure to significant amounts of water rain snow etc Vehicular Use Notice Bushnell is committed to the safe and responsible enjoyment of the outdoors Do not use this product while driving An accident can result in property damage injury or death if the operator fails to practice prudent driving practices It is the sole responsibility of the driver of any vehicle to operate the motor vehicle in a safe manner Information from the GPS unit can distract the operator of a motor vehicle It is unsafe to operate the controls of the GPS unit while operating a motor vehicle If used in a motor vehicle it must not be used by the operator of the motor vehicle If it is used in a motor vehicle it must be mounted in a manner such that it does not distract the operator does not interfere with the operator s field of view and does not block or interfere with the air bags or other safety mechanisms of the motor vehicle How Does GPS Work GPS stands for Global Positioning System Launched by the United States Department of Defense GPS consists of a constellation of 24 satellites orbiting the earth at nearly 11 000 miles These satellites are traveling at a speed that allows them to circle the earth twice each day while emitting a very low power signal The signals are timed by clocks that are highly accurate and are received by one of 5 ground stations These ground stations us
10. will result in incomplete data download and loss of data 2 After a download the unit must be powered off and then powered back on for it to recognize the data Note The unit is waterproof to 1 meter The battery compartment is water resistant If dropped in water simply open and dry the battery compartment and the USB connection area and the unit should operate 22 Glossary Accuracy A measure of how close an estimate of a GPS position is to the true location eAcquisition Time The time it takes a GPS receiver to acquire satellite signals and determine the initial position Active Leg The segment of a route currently being traveled A segment is that portion of a route between any two waypoints in the route Altimeter An instrument for determining elevation Altitude The current elevation above sea level Atomic Clock A very precise clock that operates using the elements cesium or rubidium A cesium clock has an error of one second per million years GPS satellites contain multiple cesium and rubidium clocks Basemap Built in basemaps which typically include coverage of oceans rivers and lakes principal cities smaller cities and towns interstates highways and local thoroughfares and railroads airports and political boundaries Basemaps are available in a variety of global coverage areas depending on the user s needs Bearing The compass direction from a position to a destination measured to th
11. 3 N 34 05697 z wW18 24685 Icon Selection Menu 19 Downloading Uploading and Storing Satellite Aerial Photos or Topo Maps With Your ONIX Now that you are familiar with your Bushnell ONIX series GPS you are ready to take advantage of many of the easy to use exclusive Bushnell features In conjunction with your Bushnell GPS unit you have two additional tools that make your ONIX the most functional GPS for your next outdoor excursion BushnellGPS com and the Bushnell ONIX CD with the interactive user s manual and PC program The BushnellGPS com Website Go to Bushnell s exclusive GPS website you can also access through www bushnell com to view and download Satellite photos onto your ONIX BushnellGPS com enables you to plan your next adventure by searching and viewing photos and Topographic maps Here s how to get started Log onto www bushnellgps com Click on Download Photos amp Maps As a first time user set up a User ID and Password Connect your ONIX GPS to your computer via the included USB cable e Start browsing the website for additional information on how to search purchase and download your images Once you establish your login ID bushnellGPS com saves your images in your folders on our safe and secure server so that you can access them at any time After you complete an outdoor excursion BushnellGPS com also enables you to upload all of your trip s navigation information into your account fold
12. D Distance 0 00Ft Zlo N 3405320 E 7 W118 24504 H Color Display ONIX 200 200CK GPS RECEIVER Quick Start Guide Model 45 362000 362005 ENGLISH Lit 98 0908 07 07 Thank you for purchasing the Bushnell ONIX Series The ONIX has been designed to be much simpler to operate than other handheld GPS receivers while offering exclusive and unique features such as the ability to layer satellite photos or topographic maps downloaded from BushnellGPS com right over your trail map screen providing a world frame of reference that other GPS units lack Just press the hot button on the top of the ONIX to quickly see your current location relative to the other map elements Easily create and store user profiles that let you store your most frequently used personal setups including satellite photos of your favorite camping or hunting area Bushnell s exclusive SafeTrack battery conservation feature extends your battery life while maintaining GPS contact so you can check your current location anytime without the restart delay typical of other GPS receivers You will find your ONIX to be an invaluable companion for all your outdoor adventures Before using your new ONIX please read the instructions contained in this manual and take time to familiarize yourself with the unit s operation and many great features You may want to start indoors by turning on the ONIX then pressing the Page View button to
13. Maps WAAS Enabled Download Satellite Photographs Heads Up Compass Built In SiRF Technology Built In Base Maps North America Waterproof Stores Up to 500 Waypoints amp 20 Routes Durable Rubber Armoring Save amp Load Waypoints Trails Routes SafeTrack battery saving mode 16 level Grayscale LCD Display ONIX 200CR Model 36 2005 FEATURES Same as ONIX 200 Model 36 2000 above Except Full Color LCD Display with 64K Colors for Optimum Viewing Detail Warnings and Notices GPS System amp Map Data Accuracy Notice The Global Positioning System GPS is operated by the government of the United States which 15 solely responsible for its accuracy and maintenance The system 15 subject to changes which could affect the accuracy and performance of all GPS equipment All map data sources contain some level of inaccuracies or incomplete data Bushnell strives to provide the most recent map information at a reasonable cost Warning This device 15 intended as a supplemental handheld navigation aide only The user assumes all responsibility associated with the use of this product It must not be used for any purpose requiring precise measurement of location direction distance velocity or topography This device should not be used for any aircraft navigation applications Warning Do not use this device with any batteries that have broken or cracked casings Always use fresh high quality batteries Check
14. R LIMITED WARRANTY Your Bushnell product is warranted to be free of defects in materials and workmanship for one year after the date of purchase In the event of a defect under this warranty we will at our option repair or replace the product provided that you return the product postage prepaid This warranty does not cover damages caused by misuse improper handling installation or maintenance provided by someone other than a Bushnell Authorized Service Department Any return made under this warranty must be accompanied by the items listed below check money order in the amount of 10 00 to cover the cost of postage and handling Name and address for product return An explanation of the defect Proof of Date Purchased Product should be well packed in a sturdy outside shipping carton to prevent damage in transit with return postage prepaid to the address listed below IN U S A Send To IN CANADA Send To Bushnell Outdoor Products Bushnell Performance Optics Attn Repairs Attn Repairs 8500 Marshall Drive 25A East Pearce Street Unit 1 Lenexa Kansas 66214 Richmond Hill Ontario L B 2M9 For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information In Europe you may also contact Bushnell BUSHNELL Performance Optics Gmbh European Service Centre MORSESTRASSE 4 D 50769 K LN GERMANY T l 49 0 221 709 939 3 Fax 49 0 221 709 939 8 This w
15. al copyright treaties You further acknowledge that the structure organization and code of the Software are valuable trade secrets of Bushnell and that the Software in source code form remains a valuable trade secret of Bushnell You agree not to decompile disassemble modify reverse assemble reverse engineer or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software You agree not to export or re export the Software to any country in violation of the export control laws of the United States of America 4 Table of Contents SECTION ee ere E MO ss DNOLICO etuer pane menia How Does GPS Work Software ICIS redeas tht ET cS Included In The PACMAG Battery Installation Cleaning amp Maintenance Notes ONIX Parts te doeet The Four Main Pages de ET ME TESAL PIO Ine MAP Pase VIO rosam eomm eim The NAV Pago VIO Tie SELT Pago EE ONIA eege Toe E safelrack Battery Conservation Using the Text Tool Selecting Waypoint Icons Downloading Uploading and Storing Satellite Photos amp Topo Maps with your The Bushnell ONIX GPS CD ROM Troubleshoot Ni
16. arranty gives you specific legal rights You may have other rights which vary from country to country 92006 Bushnell Outdoor Products IN NO EVENT SHALL BUSHNELL BE LIABLE FOR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER RESULTING FROM THE USE MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT Some states do not allow the exclusion of incidental or consequential damages so the above limitations may not apply to you D Customer Service 800 423 3537 www bushnell com 02007 Bushnell Outdoor Products 27 D I A OUTDOOR im TECHNOLOGY INNOVATION THAT THRIVES OUTSIDE Customer Service 800 423 3537 www bushnell com 2007 Bushnell Outdoor Products
17. backpacks and concealed areas in order to maintain consistent GPS signals Try holding the unit further away from your body Unit loses Waypoint 1 Sudden loss of power if batteries were removed 1 Removing the batteries without properly Trail Data without first turning off the power button powering down the unit will cause loss of recent waypoint and trail data The unit has been specially designed to provide a defined programmed power down sequence when the unit is shut down from the power button or when the batteries reach their cutoff low voltage level Removing the batteries when the unit is powered on will not allow the unit to go through the full power down sequence and will result in the loss of navigation data Unit freezes or 1 Processing malfunction or similar cause 1 If holding the power button for 2 sec locks up unable to has no effect remove and reinstall batteries turn off normally to reset the unit Check website for latest software update your software version is found in the Unit Info on SET page Downloaded photos 1 USB cable was disconnected or power was shut 1 When downloading information from or maps are not found off before download was completed the PC program or Web please wait or cannot be used 2 Unit was used immediately after download with until the download has been completed out restarting power off then on again Disconnecting the unit prior to completion of download
18. cuocere terum mde queri dM inco bbc EE Included In The Package e ONIX GPS Receiver USB Cable Quick Start Guide CD ROM with An Interactive Tour of the ONIX Software for managing amp saving your topo map and satellite photo downloads and planning your next outdoor excursion Battery Installation Cleaning and Maintenance Notes Unscrew the battery compartment fastening screw see next page and install 2 AA alkaline lithium or NiMh rechargeable batteries Lithium batteries are recommended for cold weather conditions and longer battery life before replacement Refer to the polarity markings inside the battery compartment to ensure the batteries are positioned correctly When removing or replacing batteries be sure the ONIX has been powered off first To reduce the chance for damage from battery leakage remove the batteries when storing the unit for periods over six months The ONIX 15 designed to be waterproof to a depth of 1 meter IPX7 rating however it is recommended that the user opens and checks the battery compartment following any submersion or prolonged exposure to rain snow etc Any moisture observed inside the battery compartment or on the exterior of the batteries should be dried off immediately and completely Prolonged submersion over 30 minutes and or to water depths greater than 1 meter can cause damage to the unit If the ONIX exterior becomes dirty clean it with a soft cloth
19. dampened with a mild detergent solution then wipe dry To avoid possible scratches a dry micro fiber cloth is ideal for cleaning the display screen Do not use chemical solvents or cleaners of any type on the ONIX unit s exterior battery compartment or display as these may damage plastic components ONIX Parts Identification Overview Hot Button controls all actions navigation initiate Where Am I feature activate SafeTrack etc SafeTrack GPS Signal Indicator Light pg 18 A ES Bushnell 5 Way Button Used to navigate on screen select from menu options and create waypoints Press up down arrows to select items in a Zoom Button Zoom the view closer in or further out on Page View Button Flips through the 4 basic screens SAT maps and photos by ch b MAP NAV SET pressing the top or menu ng t arrow to view submenus Hod das tose b fth if available left arrow to exit the l ottom part of the display options in Ib menu Press the center button Zoom contro button MAP amp NAV screens to confirm a menu selection or turn an option on or off Press the center Power Buttons located on OK button to set a waypoint right side of ONIX Push to turn on Once the unit is on pressing the power button again will turn the Battery 5 backlight on and off Push Compartment W2 amp hold button for 2 sec to turn power off Accessory Socket USB Port connec
20. e Navigate Trail below c Manage Trail shows a list of previously stored trails and allows you to edit name view or delete the trail 2 Navigate Trail navigate an existing trail This helps you navigate a trail that was previously saved You may also reverse this previous trail by then pressing the HOT button to return to the My Trails menu then choose Reverse Trail 3 Manage Trails allows you to view right arrow to eyeball icon delete or edit the details name etc of a previous trail ES Start New Trails Navigate Trail Manage Trails Ze kent Altitude 23841 8 Ft Loc 34 05329 w118 24504 _ Reverse Trails ny Manage Trails Ech kent oe Altitude 26381 17 Ft E Tem N 34 05329 W1138 24504 End Trail Menu Y New Route Navigate Route Manage Route N 0 NS RNGELES Distance 47 03 34 05341 lo wi8 24548 My Routes Menu Aerial Photo A00 100 pho sl seg 28 A00 200 pho FS A00_400 pho 00_800 P Satellite Photos List 17 ux EN Hold Hot Button AnyTime To Suspend SafeTrack Fig 21 Safe rack Selected Screen f StartSafeTrack Fig 22 0 00 Ft N 34 05329 W118 24504 Distance Right Arrow S Tracking pts min 1pts 5min B Display ON seconds 20 seconds
21. e nearest degree also call an azimuth In a GPS receiver bearing usually refers to the direction to a waypoint Start The power on sequence where the GPS receiver downloads almanac data before establishing a position fix Coordinates A set of numbers that describes your location on or above the earth Coordinates are typically based on latitude longitude lines of reference ora global regional grid projection e g UTM MGRS Maidenhead Coordinated Universal Time UTC Replaced Greenwich Mean Time GMT as the world standard for time in 1986 UTC uses atomic clock measurements to add or omit leap seconds each year to compensate for changes in the rotation of the earth Heads Up Orientation Fixes the GPS receiver s map display so the direction of navigation is always up Datum A math model which depicts a part of the surface of the earth Latitude and longitude lines on a paper map are referenced to a specific map datum The map datum selected on a GPS receiver needs to match the datum listed on the corresponding paper map in order for position readings to match Distance The length in feet meters miles etc between two waypoints or from your current position to a destination waypoint This length can be measured in straight line rnumb line or great circle over the earth terms GPS normally uses great circle calculations for distance and desired track Geocaching A high tech version of hide and seek Geocach
22. e the precisely timed signal to determine each satellite s exact position in orbit Your GPS receiver can hear the signal sent by the satellite By calculating the position and distance of at least 4 satellites accurate latitude longitude and altitude location information can be determined WAAS adds to your GPS s accuracy WAAS stands for Wide Area Augmentation System WAAS was designed by the United States Federal Aviation Administration primarily to add in the accuracy of GPS for planes WAAS consists of the group of additional ground stations placed at known and precisely located spots These ground stations then work with a master station to correct the satellite signals improving accuracy to within nearly 3 meters WAAS reception may be turned on in the SET page menu however the default setting is Off due to the additional battery drain it causes Software License Agreement BY USING THE ONIX YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT PLEASE READ THIS AGREEMENT CAREFULLY Bushnell grants you a limited license to use the software embedded in this device the Software in binary executable form in the normal operation of the product Title ownership rights and intellectual property rights in and to the Software remain with Bushnell You acknowledge that the Software 1s the property of Bushnell and is protected under the United States of America copyright laws and internation
23. ers seek out hidden treasures utilizing GPS coordinates posted on the Internet by those hiding the cache Geodetic Datum A math model representing the size and shape of the earth or a portion of it Geographic Information System GIS A computer system or software capable of assembling storing manipulating and displaying geographically referenced information 23 Glossary i e data identified according to their location In practical use GIS often refers to the computer system software and the data collection equipment personnel and actual data Global Positioning System GPS A global navigation system based on 24 or more satellites orbiting the earth at an altitude of 12 000 statue miles and providing very precise worldwide positioning and navigation information 24 hours a day in any weather Also called the NAVSTAR system GoTo A route consisting of one leg with your present position being the start of the route and a single defined waypoint as the destination Greenwich Mean Time GMT The mean solar time for Greenwich England which is located on the Prime Meridian zero longitude Based on the rotation of the earth GMT is used as the basis for calculating standard time throughout most of the world Grid A pattern of regularly spaced horizontal and vertical lines forming square zones on a map used as a reference for establishing points Grid examples are UTM MGRS and Maidenhead Heading The directio
24. ers to review and analyze and save for the next return trip BushnellGPS com also provides detailed GPS product features and specifications an Interactive User s Manual Software Update Downloads Troubleshooting and Frequently Asked Questions and the Bushnell Shopping Cart to purchase accessories Photo Map downloads and printable Photos Maps So log on log in and start downloading to experience a whole new world of GPS functionality 20 The Bushnell GPS ONIX CD ROM Your CD contains two software files to help you get the most out of the ONIX GPS 1 Interactive User s Manual Click to start this program to get an graphic interactive simulation that takes you through the basic features and functions of your Bushnell GPS This simulation gives you an informative tour of the ONIX features and allows you to practice real world navigation from the comfort of your own computer 2 ONIX GPS PC Companion program Click to install the GPS PC Companion file onto your PC The PC Companion enables you to plan and save your GPS trips on your PC Similar to the website you can upload and save waypoints trails routes photos and maps between your GPS and PC so you can trip plan even when you are not connected to the internet and BushnellGPS com Take your PC along on your next adventure and the GPS PC Companion provides the perfect tool for storing and analyzing all of your GPS information Check out http www bushnellgps com for the
25. ignal select off when using GPS indoors to extend battery life for example during basic setup operations WASS Wide Area Augmentation System On Off turning WASS on will provide slightly better GPS accuracy in the United States As this significantly decreases battery life you may want to keep it turned off for most normal navigation activities Display Fig 9 allows adjustment of display contrast and daytime or nighttime viewing mode Night reverses screen for improved viewing at night Fig 0 Increasing contrast darkens text and images decreasing contrast lightens them Sound allows selecting mute volume control key beep distance and warning sound COMPASS display options defaults are true north and numerical degrees Time sets time format 12 or 24 hr AM PM time zone daylight savings option Units selecting distance units speed and elevation GPS position format and datum default for North America 15 WGS84 see the glossary for more info Note the ONIX 200CR has a display Brightness adjustment instead of Contrast as on the ONIX200 Se Selection Gi Unit Info SET Page 2 Menu screens press down arrow to see items on second screen Fig 8 on Inland Boating D Ocean Boating Geocaching E SET Page User Profiles 13 Contrast Display Mode Normal Mode Display brightness on ONIX 200CR Fig 9 tle Ha IR mm E 28160 Night Mode Disp
26. items Fig 15 note that you can only select from previously stored items not create a new one when using the Find GoTo feature Selecting any of the items by clicking will activate navigation The title of the selected item will show on the screen and the bearing arrow will point in the correct direction to take you to it To stop this navigation activity press the HOT button again you will see the option to stop Press OK to confirm you want to stop navigating and you will be returned back to the MAP page screen but without the bearing arrow pointing the way to a specific destination Fig 15 Altitude 10887 14 Ft N 8405329 W4112 24504 Find GoTo SubMenu E The available Find GoTo items you can choose to navigate to are Nearest Waypoint All Waypoints pick from list of all closest to furthest order POI Point of Interest gas stations hospitals etc Places built into the base map city names etc My Trails pick from list of saved Trails see next section The ONIX will start pointing you to the closest point on that trail Fig 16 Fig 16 Altitude 252550 Ft gt M 34 05329 w113 24504 T Navigating to closest point on a saved trail TraiL 002 16 The HOT Button cont A trail is a previously walked path for example a trail that you took back to your campsite that wound around trees and past the edge of a pond My Rou
27. latest versions of the GPS PC Companion You can download the newest versions right from the website to any PC Just click the Product Support tab at the top of the main page then Software Updates in the left frame Visit BushnellGPS com for a detailed GPS glossary frequently asked questions FAQ and other useful information related to the ONIX series GPS receivers 21 TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION No Power On 1 Batteries are low or dead 1 Use fresh batteries in the unit Avoid 2 Power button was not pressed for 1 2 sec excessive use of the backlight which may 3 Batteries not making good contact shorten battery life 4 Battery quality issues 2 Press power button until LCD comes on 3 Reseat batteries 4 Use good quality batteries that do not have broken or cracked casings Unit does not detect 1 GPS reception is turned off in SET page 1 Make sure GPS is turned ON in the SET GPS satellites 2 Insufficient time allowed for satellite acquisition Page The center circle of the SAT page 3 Unit does not have unobstructed view of the sky should be circling If not turn GPS ON in the SET page 2 After the unit has been off for an extended time it may take longer for it to acquire GPS satellites Check the SAT page for progress 3 For fastest acquisition times make sure the unit has a clear view of the sky Avoid areas of heavy brush and areas next to large buildings or cliffs Keep unit out of
28. lay Example Affects all screens 1 Cold Start AvgSpeed MaxSpeed Fig 11 SET Page Reset Data SubMenu 14 Page View Details Reset Data Fig allows you to reset clear existing data in the selected category most commonly to clear old breadcrumb trail marks from a past trip to the area One category in the Reset Data submenu is Cold Start which will force the ONIX to clear the satellite almanac information which is stored automatically during the first power on to speed up the process of choosing the best GPS satellites for your usual starting area If this almanac data 1s no longer valid it will cause longer startup times Enabling a cold start is recommended if you have located to a new area that is over 300 miles away from your last power on position To enable Cold Start 1 Turn the unit on 2 Go to the SET page 3 Select RESET DATA and click 4 Select COLD START and click OK Note that this will only take effect the next time the unit is powered on there is no advantage or reason to enable Cold Start if the unit has already locked onto satellites in a reasonable amount of time and are still within about a 300 mile radius of the location where you first powered up the ONIX Language selects language used for all display menus and option screens Owner Info allows you to input personal information for identification shown at startup if desired Please refer to Text Entry
29. n in which a vehicle is moving For air and sea operations this may differ from actual Course Over Ground COG due to winds currents etc Initialization The first time a GPS receiver orients itself to its current location and collects almanac data After initialization has occurred the receiver remembers its location and acquires a position more quickly because it knows which satellites to look for Latitude A position s distance north or south of the equator measured by degrees from zero to 90 One minute of latitude equals one nautical mile A portion of a route consisting of a starting from waypoint and a destination to waypoint A route that is comprised of waypoints A B C and D would contain three legs The route legs would be from A to B from B to C and from C to D eLongitude The distance east or west of the prime meridian measured in degrees The prime meridian runs from the north to south pole through Greenwich England Magnetic North Represents the direction of the north magnetic pole from the observer s position The direction a compass points Display A graphic representation of a geographic area and its features Nautical Mile A unit of length used in sea and air navigation based on the length of one minute of arc of a great circle especially an international and U S unit equal to 1 852 meters about 6 076 feet eNavigation The act of determining the course or heading of movement
30. nts may also be put into the unit by referencing another waypoint already stored giving the reference waypoint and entering the distance and compass bearing to the new waypoint Wide Area Augmentation System WAAS A system of satellites and ground stations that provide GPS signal corrections for better position accuracy A WAAS capable receiver can give you a position accuracy of better than three meters 95 percent of the time At this time the system is still in the development stage and is not fully operational WAAS consists of approximately 25 ground reference stations positioned across the United States that monitor GPS satellite data Two master stations located on either coast collect data from the reference stations and create a GPS correction message WGS 84 World Geodetic System 1984 The primary map datum used by GPS Secondary datums are computed as differences from the WGS 84 standard 25 26 Compliance Statement The ONIX complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE These limits are designed to provide reasonable protection against harmful interference in a residential installation and are more stringent than outdoor requirements Operation of this device is subject to the following conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired
31. ods that can be used to manually enter the coordinates latitude and longitude for a location into your ONIX GPS unit Enter the coordinates using the PC Companion software then transfer them to an ONIX connected to your PC via USB eGo to MAP page and press the HOT button Then select Find Go To and select Location You can then enter the coordinates for the location using the type tool Select OK when finished this will display the location on the MAP page allowing you to press and hold the OK button again to mark the location as a waypoint eA third option is to select Position as a data field on the MAP page then scroll the crosshair cursor to the location using the 5 way switchpad and mark a waypoint Safe Track A Fig 14 05 ANGELES Altitude 94028 Ft H 34 05329 f 57 wM48 245047 Hot Button Menu 1 THE HOT BUTTON Once you go to the MAP page all your navigation actions are easily controlled by Bushnell s exclusive button From the MAP page click the HOT button to view its menu then arrow down to select an item Fig 14 The first highlighted item is always Where Am I press OK to see your current location on the map display This function lines up the GPS position icon You Are Here with the crosshair pointer Location HE icon The next HOT button menu item is Find Go To Click OK or right arrow on 5 way button to find or go to any of the listed
32. page provides a compass only display The view options of the NAV page include Fig 5 Heading Arrow if user selected Small arrow head only Indicates the direction you are actually moving in Bearing Arrow Fig 6 only appears during active navigation This will be seen as a long black line with an arrow head It indicates where you should go to get to your navigation destination North Arrow if user selected points to true or magnetic north user options Identified by N circle at head of arrow NAV data boxes as described previously in the MAP Page View section Page View Details The user selected options are accessed by holding down the PAGE view button for 2 seconds then using the 5 way button to select and confirm the desired option 4 SET Page View The SET page user options Fig 7 span two menu screens and include all the following User Profiles Fig 8 select to customize and set various display options You can save different sets of screen configurations that are best suited to your different activities To save a profile select an activity from the list hiking camping etc then presstherightarrow to save your current display configuration under that name The checkmark indicates the current active profile One custom user profile may bet setup and selected in addition to the other five pre named profiles for common activities GPS On select on to navigate and locate GPS s
33. phic map you choose from files you download and store in the ONIX will be layered over the base map North UP arrow which points to North true or magnetic user selectable Will always automatically be shown when satellite photos or topo maps are layered Range Ring visual tool that represents distance on your map or photo within a circle The distance shown 15 the radius of the circle This radius is half the zoom level Photos Satellite superimposed over Base Map if desired You do not need to manually select the right photo or topo map to use as these downloaded files are geo referenced enabling your ONIX to choose the correct photo automatically based on your current location and zoom level Note that while both types of images can be stored at the same time on your ONIX only one of them photo or topo map can be layered over the base map at a time not both at once My Map Data turns on off display of roads and places on the base map BreadCrumbs a dotted line on the display showing the simple path you ve traveled Breadcrumbs are automatically stored but only displayed if this option 15 selected Upper Navigation Data Box BreadCrumbs g Point OF Interest H 34 0324 W118 24504 MAP Page Display Options Lower Navigation Data Box 11 Fig 4 Altitude 1060 5 Ft M 34 04G04 W113 22420 D NAV Page Magnetic Worth Fig 5 34 04G6G04 W118 22420 i Fig 6
34. point you can confirm you want to set the waypoint by clicking OK again and it will be set You also have the options to arrow up to edit the waypoint name select its icon or set an alarm when the waypoint is reached You can go back and edit these options at anytime even after you have clicked twice to set the waypoint If you choose not to set the waypoint or you want to delete the waypoint select the left arrow and go to the delete options Fig 13 To edit the text arrow up to the waypoint name Fig 12 then click OK and use the keypad screen you will see to create a name to replace it see pg 19 for details on using the text tool for naming You can also move down to select the icon and again press OK and choose from the available different icons see pg 19 Move down to the alarm icon in the popup window and press OK to turn on the alarm for that waypoint The last item in the popup allows you to delete the waypoint you will be asked if you are sure to prevent accidental deletions M d P1 2 Set Waypoint Los ANGELES AN LL CD D IO Distance 47 03 d H 34 0534 Wiig 24548 Set A Waypoint Are you sure delete waypoint LOS ANGELES Distance 47 04 H 34 05341 TN GER oc Edit Waypoint Menu SIA 15 MAP Where I Find 7 Go To I Using Your ONIX 5 The Button There are several meth
35. r Editing Names of Waypoints Trails and other items Anytime a name field is highlighted click OK to bring up the text entry tool Fig 25 This is a multi function tool that is controlled by the 5 way button Your current selection is always highlighted Move left right or up down to select letters and numbers then press OK to enter your selection To add a space or backspace press and hold the down arrow button then highlight either Back or Space To move from the letter field to the number field press and hold the right arrow To access symbols press and hold the left arrow Hold the up arrow to access the Shift for upper case letters etc and Done when you are finished and ready to exit the text entry procedure functions Fig 26 shows an example of using the text tool to enter the owner s information on the SET page Selecting Waypoint Icons After the waypoint icon is selected highlight and press OK in the Edit Waypoint menu of the MAP page see pg 15 the display will show a menu of icons 27 or common symbols that you may choose to represent your waypoint on the map If you have previously set up a user profile for a particular type of activity for example camping the group of icons that appears in the icon selection menu will be the ones most related to that activity me Ze N EN WII Z Text Entry Tool State 09 N N 248 218 0 2 fni Distance
36. rt SafeTrack and press OK to enter and start SafeTrack automatically When you are in SafeTrack mode the display screen is off but the green indicator light will blink periodically To return to screen viewing and active navigation hold the hot button for 2 seconds Note that as long as you are actively using the GPS and pressing buttons within time limit set in SafeTrack options the screen display will stay active but the unit is still in SafeTrack mode After a period of inactivity length of time selectable in SafeTrack options menu the Start SafeTrack screen Fig 22 willappear You can also get the Start SafeTrack screen by selecting SafeTrack from the HOT button menu SafeTrack cont Text Tool Waypoint Icons If you want to return to SafeTrack mode simply do nothing the unit will automatically re enter SafeTrack If you do not want to return to SafeTrack but wish to remain in the SafeTrack active mode arrow down to the Wait option At the Start SafeTrack screen you also have the option to view and change your SafeTrack Options display inactivity time alarm tracking point frequency etc To view the SafeTrack Options screen Fig 23 press the Right arrow from the Start SafeTrack screen To fully exit SafeTrack press the Left arrow from the Start SafeTrack screen to get the Stop SafeTrack screen Fig 24 then select Yes to return to normal operation Using The Text Tool Procedure fo
37. run through the four basic screens SATellite MAP NAVigation and SET up while reading the manual section for each After that practice using the hot button and 5 way switch to see and select from a menu of options perhaps on the SET screen by setting a few personal preferences for information displays Once you begin feeling more comfortable with the controls and screens the best way to really learn to use your ONIX 15 to take it outside right in your own neighborhood or a local park and let it lock onto the GPS satellite signals as you watch the SAT page be patient this can take 3 or 4 minutes the first time you use it make sure you have a clear view of the sky and are not right next to a large building for best results then take a short walk and finish by using the ONIX to guide you back to your starting point you can either mark a waypoint at the start by clicking the center of the 5 way button twice or just begin walking later following the dotted breadcrumb trail back After that you might try downloading a satellite photo of this local area layer it on top of the map screen and try walking the same trail again setting a few waypoints as you go Continue referring to this manual and practicing as often as necessary until you master the basics before heading out on a hike of any major length or attempting to navigate an unfamiliar area ONIX 200 Model 736 2000 FEATURES 20 Channel GPS Receiver Download Topographic
38. sing the Page View button after you are on the SET page will go back to the SAT page the button continues to cycle through the pages in order 10 M 34 05329 W118 24504 Altitude 1488 0 n M 94 059320 W118 24504 MAP Page with Compass layer Page View Details 1 SAT Page View Fig 1 The SAT page view is used to identify the quality or strength of the satellite signals being received by the unit Navigation data boxes on the satellite page are used to identify your location shown as POSition latitude longitude and ELEVation altitude above sea level The items displayed on the satellite page view are fixed and cannot be changed by the user Note initial satellite contact may take 3 4 minutes but will be faster on next power up in the same area If the unit has been moved over 300 miles since was last used resetting this startup location data by enabling a cold start initial power on can provide faster lock times see Reset Data on pg 14 for details 2 MAP Page View Fig 2 The MAP page view is the primary page you will use to navigate with the ONIX Using Bushnell s exclusive screen layering this page shows all navigational information in a single view on one display The following items are always displayed on this page Base Map primary streets and location similar to a basic road map also see My Map Data pg 11 Cursor shows your location and direction The cursor can
39. t to PC with supplied cable 7 The Four Main Pages Overview There are 4 different pages you can select from to view on the display screen To cycle through these pages in their order as shown below press the Page View button on the top right of the ONIX The pages and their function are 1 The SAT Satellite Page The purpose of this page is to enable the user to view information related to the reception of GPS satellite signals by the ONIX You can see how many satellites are providing location data to the ONIX the unique ID of each satellite how strong the signal is from each one bar graph at bottom and the accuracy of the location data the ONIX is providing based on the quality quantity of satellite signals currently available A EUR This page 15 useful for trouble shooting if S EDEN the GPS does not seem to be working as it should 2 The MAP Page You will spend the majority of your time on this page once youare setup and actually using your GPS to navigate Your current position is shown on a base map like a simple road map using one of 3 kinds of cursors along with any or all of the other items you may choose to display such as satellite aerial photos or topo maps a compass special points of interest and other data you may want to see These additional items may all a 3405370 be viewed together as layers on top of the 02 w448 24504 base map Altitude Z5255 0 Ft 2 MAP Page
40. tes pick from your list of saved routes point to point navigation My Photos or Topos after you pick a photo or topo from the list Fig 20 arrow down to it and press OK to confirm you wish to navigate towards that area the ONIX will begin to point you towards that area Note that you must have selected photos or topos as a screen layer in your MAP options as described earlier on page 11 if you want to see it while navigating Alternatively instead of pressing OK you can right arrow from the name on the list and go to the eyeball icon then press OK to just view the photo or topo without starting navigation To exit this view only mode press OK again to return to the list Location manually enter a known latitude and longitude coordinate Following Find GoTo the next HOT button menu item is My Trails A trail is a path or course that been previously traveled by the user Press OK or the right arrow The three options are Fig 17 1 Start New Trail press OK you are now ready to build a new trail from your current starting point To end or reverse an active trail press the Hot button once Go back into the My Trails menu press OK and you will see the menu shown in Fig 18 with the following choices a End Trail selecting this will prompt you to confirm you want to stop the trail b Reverse Trail select this to reverse a trail return to the starting point of a trail that has not yet been ended Also se
Download Pdf Manuals
Related Search