Windtower information technologies Co.,Ltd
Contents
1. Compatible to IEEE 802 3u 100BASE TX fast Ethernet 6 Networking Mode 6 1 Typical Applications The IAD user gateway integrates the Internet gateway and VoIP gateway into a box Small size enterprises can use the 10 100Mbps LAN interface to connect local PC with uplink connected to DSL Modem or Cable Modem They can also use category 5 cables to connect the ISP switch as shown in Fig 1 Two FXS can be connected to two ordinary analog telephone sets to provide conversation based on IP network The IAD user gateway also is the ideal access equipment for small and medium scale of telephone bars as shown in Fig 2 The FXS port can be connected to two ordinary telephone sets The uplink can be connected to the ITSP Internet Telephony Service Provider network through an Ethernet interface connected to the small switch or router Page 6 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual OSS NMS AS DBY m Internet VOIP System Architecture for Small size Enterprise Branch Copper Cable DSL Ordinary analog telephone set OSS NMS AS DB Sa Pl lust install the browser and log in to the CSC to become a powerful billing terminal ee ee 7 aa 79 Ka M L PZE oes y i p m i L i pp r a ba IP terminal telephone set Ordinary telephone set Ordinary telephone sel Ordinary PC browser Operator IP Telephone Bar System Architecture2. Catogory 5 Cable Page 7 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 7 Appearance Description WAN Interface LAN Interface FXS FXS 12V 0 8A Adapter 8 Configuration Description The IAD provides two ways to modify WEB parameters through LAN interface and WAN interface Below describes how to enter the WEB interface configuration parameter refer to Chapter 9 WEB configuration interface description through LAN interface refer to Section 8 1 or WAN interface refer to 8 2 8 1 LAN Configuration Environment B Configure the TCP IP Protocol of PC according to Fig 1 with the default IP addresses of PC and IAD LAN in the same network segment m Use straight through cables in the figure R After configuration input the IAD default IP address in IE address bar Each IAD will be allocated with an initial Lan IP address before delivery assumed to be 192 168 0 200 Page 8 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Internet Protocol TCP IP Properties 2 x General TOU can getlP settings assigned automatically if your network supports this capability Othenwige you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 12 766 0 115 Subnet mask 255 255 4a R Default gateway 12 1768 0 1 C Obtain DHS server addre
3. indicate the IP address range to use for DHCP assignments to the LAN Specify the domain name optional that is provided to LAN clients via DHCP Two optional static DNS server IP addresses can be entered that will be provided to LAN clients via DHCP These are in addition to the DNS servers automatically provided by WAN connections Press Save DHCP Settings to save and apply the DHCP server settings Any new settings will take effect immediately In addition up to 8 static DHCP address assignments can be configured To add a static IP assignment enter the LAN device s name must be unique in the private network and or MAC address Specify the static IP to be assigned and press the Add button To remove an existing entry press the Remove button next to the entry to be removed To view the current active DHCP client binding table the internal list of devices for which the server has provided an IP address lease press View DHCP Table A popup window will appear displaying the list of bindings Press Update to update the binding information Press Close to close the binding table window To clear the device s internal DHCP client binding table press Clear client binding table Be aware that doing this will destroy the DHCP server s knowledge of the LAN clients it has provisioned and may result in client problems when a client tries to renew its lease Page 15 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway
4. Cadences required by Rings Call Waiting Indicator and Distinctive Ring features 1 Ring Configuration Default Ring Default ring cadence when the phone rings Call Waiting Reminder Ring Ring cadence of Call Waiting Reminder Ring Page 21 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 9 5 CODECS Setting Wish LAN CODECS SIP Selected Silence Suppression CODECS eau Advancecet L 6711A System C 6723 Download C 6726 ON iw Configuration 6730 on LogOQut Reboot mee Packetization Jitter Buffer Adaptive Jitter Buffer Looms rmaximum playout delay in milliseconds Fixed Jitter Buffer Ams 7 fixed playout delay in milliseconds E Automatically switch to Fixed Jitter Buffer upon Taxirmpd prm tone detection Save CODEC Cantiguration 4 If the device is running one of the four VoIP applications this page is available for configuring the audio CODEC parameters as well as the Jitter Buffer settings for the CODEC decoders Enter which CODECs are to be supported Select which complex codec is to be supported Due to memory limitations it is not possible to select G723 and G729 complex codec at the same time Select the packetization period to be used for each selected CODEC Select whether Silence Suppression is to be supported for each CODEC The Jitter Buffer settings apply to all active CODEC decoders You may choose between an adaptive jitter buffer and a fixed jit
5. Gateway User s Manual 9 9 Reset Setting 3 i i i E WAN LAN Reset SIF You must reboot to make your changes active CODECS Warning Resetting the system will terminate all network connections and reset your browser connection Reset and execute Main Application System Download Reset and execute Downloader Application Configuration Log ut Reset Reboot This page provides options for resetting the device Select whether you wish to reset the device and start executing the main default application or whether you wish to reset the device and start executing the internal downloader application Press Reset to reset the device 9 10 Config Backup Home Backup Restore WAN LAN Configure File Backup SIE N CODECS a Backup Configure File j System Download Configuration Logdut Reboot Backup configuration values of system settings to a file from the device Click Configuration item on the top menu Click Backup item on the left menu Press Backup Configure File button to save configuration file Page 28 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 9 11 Config Restore Home Barkun Restore VAN LAN Configure Restore SIF a a CODECS Configure Restore method Select filename on local browser machine Advance set Filename f System Start Download Download Configuration LogOut Restore Factory Default Reboot Start Resto
6. User s Manual Home LAN Status LAN Setting CHEF Fouting Port Forwarding VLAN MMA Port Fonwarding Configuration CODECS Reserved Ports Advarnceset The following ports have been reserved bythe CPE and may not be forwarded to the LAN S 66 5060 5070 8000 8015 7001 7005 5555 80 23 161 Download noes l Port Forwarding to LAN Configuration Por Range Protocol Destination Address Reboot aalas DeMilitarized Zone lf specified packets which port are not listed above will be forwarded to this DZ host 192 168 0 al Save WAPT Settings This page allows the user to customize the devices port forwarding feature The port forwarding feature does not apply if the device is operating in bridge only mode Port forwarding provides WAN access to the internal LAN by specifying that traffic over certain ports are to be directed at particular LAN hosts This feature is available only in router mode Up to 8 ports forwarding entries Pinholes can be configured To add a port forwarding entry configure the Port Range to be forwarded the Protocol to be forward TCP UDP or both and destination LAN IP Address press the Add button to add the entry To remove an existing entry click the Remove button next to that entry you wish to remove Note that certain port numbers are reserved by the CPE for its own internal use These ports may not be used for port forwarding to the LAN Ports which may be reserved by the CPE include those
7. the No prefixed with 86 amp 88 eg when call 81971911 the send no will be 075581971911 Digit Map 3 For the No prefixed with 86 86 will be dropped eg when call 8607552647xxxx the send no will be 07552647xxxx Digit Map 4 For the No prefixed with 88 no change eg when call 88011500 the send no will be 88011500 Home niai pian FyoSet AdvanceSet WAN LAN Radius Billing setting CODECS HotLine Setting AdvanceSet T Ol Use FXS Hotline Number fo O Use FXO Hotline Number fF SVG ZI Download i E Pstn dialout NUM Setting Configuration Pstri priority Pstn Dialout Number ls LogQut Reboot Encrypt Setting I Use Encrypt Enerpyt Way EneryetKey Es RTP nyt Voip server use time limit O USE time Limitieg 20060804 sid Polarity billing Setting E CI Use polarity billing we Save Setting Radius billing Setting Start billing software Enable Use Radius server lp check button enter the IP address of target computer Use FXS Hotline Number Enable Use FXS Hotline Number check button when you pick up telephone receiver the HotLine No will be send automatically immediately PSTN Dialout Number Lifelive setting Encrytp setting association server setting Use Time Limit Setting the expire date of account No Polarity billing setting Enable Use Polarity billing check button will Start Polarity billing function Page 27 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202
8. And hang up the phone will stop IVR Page 31 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 100 Network status None DHCP setting 1 to enable 2 to disable or back to menu IP address setting Use to instant of and to end Ex 172 16 230 227 Or back to menu Gateway setting Use to instant of and to end Or back to menu Net mask setting Use to instant of and to end Or back to menu Page 32 of 32
9. Call Waiting Reject second incoming call System C Disable Caller ID Display Download C1 Call Hold using c 0 0 0 0 RFC 2543 in SDP Configuration send NOTIFY for REFER request Log OUL C send Message Waiting Indicator MV SUBSCRIBE command Reboot SIP Timers Cl Send INVITE with Timer headervalue Seconds Cl SIF Session Timer value eas seconds Conditional Call Forwarding Timer seconds Inter Digit Timer seconds SIP T1 Timer Miliseconds SIP T2 Timer Milliseconds SIP T4 Timer 5000 Williseconds z Save SIP Extension Settings This page allows specification of the SIP signaling stack behavior under certain scenarios lt If you wish for the SIP stack to implement reliable transmission of provisional responses according to RFC 3262 using the PRACK method check the option Support PRACK method with provisional response reliability If you wish for the SIP stack to include the user parameter user phone in the SIP URI header s check the option Encode SIP URI with user parameter If you wish for the SIP stack to send INVITE messages with the Timer header field present check the option Send INVITE with Timer header value and enter the Timer header value If you wish for the SIP stack to implement a session timer according to draft sip session timer select the option SIP Session Timer value and enter the session time out value Press Save SIP Extension Settings to save the new value
10. OGIN WEB Through IAD s Wan or Lan IP to login web Default Admin Username admin Default Admin Password 888888 Default User Username user Default User Password 888888 When login as admin user will see like figure 7 Home w WAN LAN Welcome to IAD download and configuration utility It support SIP H323 download it for you need SIP Select from the configuration options in the menu on the left CODECS System Information System Download Configuration LO9 OUT Reboot Voip gateway made in china When login as user will see like figure 8 Home w WARNI System Uptime 0 days Oh 20m 378 Image Version cos sz vr0600681 2 bin NTP time 12 01AM 06302006 GMT 8 DST LAN IP Address 192 166 0 200 Static MAC Address 000345687 Security Password installed Fig 7 LAN Welcome to IAD download and configuration utility lt support SIP H323 download it for you need System select from the configuration options in the menu on the left Configuration Log Ou system Information Reboot Voip gateway made in china System Uptime 0 days Oh 14m 44s Image Yersion cos sz vrO6b00812 bin NTP time 11 55PM 06 29 2006 GMT 8 DST LAN IF Address 192 168 0 200 Static MAC Address OO S0 f 34 56 87 Security Password installed Page 11 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD 9 2 WAN Configuration Home WAN E WAR Setting RIS IPSEC VLA MAC Spoofing WAN LAN WAN Status SIP Interfac
11. Reboot Reorder Tone 4508 10 450 10 0N 350 OFF 350 50 R ee cases A508 10 4508 10 4508 10 4508 10g0N 100 OFF 100i R hMessage VVaiting Indicator Tone Call yvaiting Indicator Tane 4504 10 4508 lO ON 100 OFF 100 10 R 4508 10 0N 150 OFF 450 ON 150 OFF 4000 R This sub page is used to configure Tones which applies in order to acknowledge users Dial Tone The tone you hear when you pick up handset Recall Dial Tone The tone when you hold callee and prepare to make another call Confirm Tone The tone after you ve set up some service like DND Do Not Disturb Call Forwarding etc Ring Back Tone The audible ringing you hear before callee picks up and answers your call Page 20 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Busy Tone The tone indicates the number you dialed is in busy now Reorder Tone The tone you hear if you dial an invalid number or the call is not available Receiver Off Hook Tone The tone to alert you to place the handset on hook Message Waiting Indicator Tone The tone to notify you to call for message box Call Waiting Indicator Tone The tone to make you aware of the second incoming call while you re in conversations Ring Ring Configuratioin Default Ring OW 10001 OFF 2000 H Rerninder h Reminder Ring ON le5 OFF 625 lt DN 2000 OFF 2075 H Save Tone and Ring Settings This sub page is used to configure Ring
12. WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual WT 3202 VoIP Gateway User s Manual lt Version V1 1 A gt Congratulations on your purchase of the product Please read the manual carefully to ensure your gateway work in best status Security and Notes Don t use it in chemical plant gas station or near the exploder place Don t use it near the equipment easy to be interfered by wireless Avoid using it in too high or low temperature and avoid exposing the product in sun or high humidity condition Note The specifications and information regarding the products in this manual are subject to change without notice We reserve the right of improving the product without informing users and ultimate interpretation right of its performance Copyrights 2004 2006 All Rights Reserved http www windtower com cn Page 1 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 1 Revision information Revision History 2 Terminology Terminology Name Note Page 2 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Contents DOVE CNW TTT 4 2 PACHA ot reeset oe cece cece neers a E EE E E 4 3 Safety INSTUCHONS sessirnar AE E RAAE 4 ENO CIC ion TO TAD EE E A E E 5 D Perlormance lle T 5 O ING IW ORKIMNG MOOG iunais ara a E a a a 6 6 1 Typical e e eT 6 7 Appearance Re vle le s sess ianea a AAE EE Aani 8 8 Configuration Descripti
13. ation of the out of band signaling options for SIP Select whether OOB telephone event signaling is to be done using the SIP INFO message or to be done via RFC2833 RTP signaling Page 19 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Home Server Extensions User 1 Sip Book OOB Signalling ToS DiffServ Tone Ring VLAN WAN LAN ToS DiffServ SIP CODECS Call Signalling Packets 2 Hex digit byte value Advanceset RTP Packets 2 Hex digit byte value System Download mae o l Save ToSDittSery Settings configuration LogQut Reboot This sub page is used to configure the Type of Service Diffserv byte values which are to be used in the IP header of all transmitted SIP signaling packets and RTP packets The ToS DiffServ byte values are entered as two digit hexadecimal values If no special ToS DiffServ value is to be used for a particular traffic type enter 00 or leave the setting empty Press Save ToS DiffServ Settings to save these new settings Tone Hamme Server Extensions Wiser 1 Sip Book ODA Signalling ToSibiServ Tone Ring VLAN WAN LAN Tone Configuratioin SIP CODECS Dial Tone 4508 1log0N 1000 R Recall Dial Tone 4508 10 4508 108 ON 100 OFF 100 3 0N 1000 R System er Confirm Tone 450 104 4508 108 0N 100 OFF 100 3 0FF 1000 8 Configuration Ring Back Tone 4500 10 4500 10 0N 2000 OFF 4000 R Log ut Busy Tone 4504 10 4508 lOa ON 350 OFF 350 50 R
14. by comparing the current dial string against the dial plan if the result is under qualified partial matches at least one entry then it will do nothing further If the result matches or is over qualified no further digits could possibly produce a match then send the string to the gatekeeper and clear the dial string The Timer T is activated when it is all that is required to produce a match The period of timer T is 4 seconds For example a dial plan of xxxT xxxxx will match immediately if 5 digits are entered it will also match after a 4 second pause when 3 digits are entered D 1 Sample Dial Plans Simple Dial Plan This allows dialing of 7 digit numbers e g 5551234 or an operator on 0 Dial plan is OT xxxxxxx Non dialed Line Dial Plan As soon as handset is lifted the unit contacts the gatekeeper used for systems where DTMF detection is done in call Dial plan is x i e match against 0 or more digits Note the dot Complex Dial Plan Local operator on 0 long distance operator on 00 four digit local extension number starting with 3 4 or 5 seven digit local numbers are prefixed by an 8 two digit star services e g 69 ten digit long distance prefixed by 91 and international numbers starting with 9011 variable number of digits Dial plan for this is OT OOT 3 5 xxx 8xxxxxxx xx 91XXXXXXXXXX 9011x T 12 1 2 IVR To use IVR one should pick up the phone and then dial four consecutive asterisks
15. configuring the device s SNMP manager Configure the SNMP Trap Host IP address and community the SNMP read and write community parameters and the SNMP System Description and System Object ID parameters Press Save SNMP Settings to apply the new values These settings will only take effect when the device is rebooted Page 24 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Home Security Timeout Localization Handset SMMP Service Access AT LAN Service Access Configuration SIF CODECS Select which interfaces are alowed access to the services listed below Advanceset System LAN WAR S HTTP Web access Configuration SNMP LogQut TELNET Reboot Save Service Access Settings lf the device is a multi interface device bridge router then this sub page is available to enable disable access to certain system level network services on the device s interfaces From this page an administrator can choose to allow or disallow HTTP SNMP and Telnet access from devices on the LAN or WAN or both Care must be taken while configuring the HTTP access as once you have saved you will no longer be able to access the device s web pages if you have disabled HTTP on the interface you are currently accessing the device on Press Save Service Access Settings to save and apply the new access settings 9 7 Download Setting This page provides two options for downloading a new firmware application image
16. e Status Himes Enabled Yes mes Service Routed Protocol Ethernet System Interface Status Up acetate Link Status 10M bps Half Duplex configuration Network Settings Logout Dynamic IP Assignment MO Th IF Address 192 168 1 251 Reboot MAC Address 00 90 12 3234 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 DNS Address 202 965 134 133 Domain Mame VLAN Tag Mot set Priority Tag Mot set Broadcast limit Multicast limit Update 100 fof downstream bit rate 100 fof downstream bit rate WT 3202 Gateway User s Manual This page is the first page displayed when the device s web pages are accessed It shows how long the device has been running since its last reboot the IP address the device is currently using whether or not the device is password protected and also displays the main application and downloader application firmware versions In addition MAC address of the WAN port and serial number of the device if it has one are also displayed in this page Home WAN Status WAN Setting PPPoE IPSEC VLAN MAC Spoofing WAN LAN WAN Configuration SIP CODELC 2 Device Operating Mode Advanceset system Obtain WAN configuration dynamically Download Specify fixed WAN configuration Configuration IP Agere LogQut Reboot Uplink Configuration z Uplink Bandwidth ikbitsisec This page and its sub pages are available on device that supports routing bridging and allows viewing and config
17. ing services As an Integrated Access Device the upstream port of the IAD can be directly connected to the IP network and its downstream port can be connected to multiple ordinary telephone sets to provide basic accesses for POTS users This user port gateway can support two telephone lines and connect multiple telephone sets At the same time this device is capable of Internet gateway and can access data stream such as Email or Internet information It is also applicable for small size enterprises and IP telephone bars 2 Packing The IAD is packed with color chassis Upon receiving the product please confirm whether the fittings are complete The packing box contains a set of IAD 1 piece of RJ45 network cable one IAD power adapter and user s manual 3 Safety Instructions To ensure your safety and safe use of this product please pay attention to the following items B Follow the instructions in the user s manual m Keep the device far away from chemicals and regent R Store use the equipment in dry and well ventilated environment m Never open the chassis lest the device is short circuited or damaged Page 4 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 4 Introduction to IAD The IAD works with the most popular LINUX embedded operation system and has special CPU and DSP compression algorithms featuring universal functions and applicable to a wide variety of needs Basic feature
18. ion bitrate PHY Speed mode AUTO Negotiation Save LAN Settings LogOQut Reboot This sub page allows the user to configure the private LAN interface settings Assign an IP address to the LAN Ethernet port This IP address is also the default router address for the devices on the private LAN The default LAN interface IP address is set to 192 168 0 200 Enter the subnet mask for the private LAN If you wish to set the broadcast and multicast limits for the bridge router enter these values as percentages of the LAN interface Ethernet bit rate Leaving these values blank will imply values of 100 Press Save LAN Settings to save and apply the LAN interface settings Any new settings will take effect immediately Page 14 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Home S LAY Status LAM Setting DHCP Routing Port Forwarding VLAN WAN DHCP Server Configuration CODECS Server Settings AdvanceSet Enabled Disabled System Client IP Address Range 192 168 0 100 Download Configuration Client Network Information Rebaat Static Address Assignments Identify Using Host Identifier Internal Address Save DHCP Settings iew DHCP Table This sub page allows configuration of the private LAN DHCP server The DHCP server settings do not apply if the device is operating in bridge only mode Specify whether the device s internal DHCP server feature is enabled or disabled Also
19. lization Handset SNMF WAN LAN Localization SIF POUES Country system Time Zone GMT 1 2 00 Eniwetok Kwajalein w Download Gaee E Adjust clack for daylight savings LoqgOut Reboot Save Localization Settings Timezone Find the current time from a list of cities Country Caller ID Page 23 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual The caller ID can find out who s calling you and keep track of how often they call Users should set the country field according to their geographical location otherwise the Caller ID function might not work properly 1 Timezone setting Click System on the top menu Click Localization on the left menu In NTP Server field enter a NTP server IP address If you want to use the default NTP server this field should be blank In Time Zone drop down menu select one time zone In Adjust clock for daylight savings checkbox if your country has daylight savings time you can enable it Press Save Localization Settings button then system will redirect to the web page of reset Home Security Timedut Localization Handset SNMP WAN LAN SNMF Configuration SIP CODECS SNMP Trap Configuration Advanceset IP address f Trap Community f System Download SHMP Community Configuration Configuration Read Community Write Community LogQut eee Reboot SNMP System Configuration Save SNMP Settings This sub page is used for
20. n A dial plan gives the unit a map to determine when a complete number has been entered and should be passed to the gatekeeper for resolution into an IP address Dial plans are expressed using the same syntax as used by MGCP NCS specification The formal syntax of the dial plan is described by the following notation Digit 0 1 1 2 3 4 5 6 7 8 9 Timer T t Letter Digit Timer A a B b C c D d Range X x matches any digit Letters matches any of the specified letters Letters Subrange Subrange Letters Subrange Letter matches the specified letter Digit Digit matches any digit between first and last Position Letter Range StringElement Position matches any occurrence of the position Position matches an arbitrary number of occurrences including 0 Page 30 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual String StringElement StringElement String StringList String String StringList DialPlan String StringList A dial plan according to this syntax is defined either by a case insensitive string or by a list of strings Regardless of the above syntax a timer is only allowed if it appears in the last position in a string 1213 is not valid Each string is an alternate numbering scheme The unit will process the dial plan
21. o server in specific time and the echo count is used for disconnecting this PPP connection if the device does not receive the response of echo request If the PPPoE server service provider requires any special Service Name or AC Name to be set you can specify these tags here Press Save PPPoE Settings to save and apply the WAN interface PPPoE client settings Any new settings will take effect immediately Home a7 WAN Status WAN Setting PPPoE IPSEC VLAN MAC Spoofing WAN LAN MAC Spoofing Configuration SIP 6 Stes WARN MAC Address Spoofed nal System Save MAC Spooting Settings Download Configuration LO UOU Reboot Page 13 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual For the setting of MAC Spoofing if two IADs are configured with the same MAC address they cannot establish conversation 9 3 LAN Configuration This page allows configuration of the device s local network settings Sub pages are available for the following on the left of page the LAN interface status configuration of the LAN interface settings and configuration of DHCP server settings and Port Forwarding NAPT Settings Home Bee LAN Setting DHCP Routing Port Forwarding VLAN WAN LAN Configuration CODECS Hetwork Settings AdvanceSet IF Address Download Configuration Multicast Limits Broadcast limit 100 of Ethernet connection bitrate Multicast lirit 100 a of Ethernet connect
22. on ssssssss sss sese esse see ss sees eena ennenen eenn ennenen ennenen 8 8 1 LAN Configuration Environment sees ee eee ee e ee e eee 8 8 2 WAN Configuration Environment sse eee eee ee e ee e eee 9 9 Configuration in WEB Mode cesses ssssssssssssssssseeesss enesenn nenen nenen 11 Se LAIN K T 11 92 WAN COMO AUN set wenn sacieresesce dente a o ee TEESE EEEL OEE E e E 12 9 3 LAN OGURA ie 14 94A SIP COMO Ua OM serret redenn a EREEREER EER ARE EE 17 Do CODEC o EUO eare e E E E E E RE A EERE EEEE E 22 G LT UE e e a E E EE S E EE 23 IT Rees ko CN ee E E E E E E ee eee 25 OS PVA Cee TING e E E E E S 26 ZES Ee Se UU o E E e E E A N T E see A E AE 28 TO Conid l ei Ie 28 gA Cong lt e 29 10 Da ModE sienna iaa eae E s 29 11 TO CSS NO ONG oie se cece hacen ep sce aces Se nsec aa E aa a Aaaa EN 30 12 Dial Plan And IVR sess cies chit eee vent aaa a aa aaaea EE aiaa 30 E TDAP T 30 55 KA i a EE A EN E T ee E eee een A E E ree 31 Page 3 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 1 Overview The popularization of the Internet drives the rapid development of a wide variety of IP based applications The IP telephone technology has become the major means for operators to develop voice services now Especially IP technology becomes the core of the next generation network NGN so the IP based voice technology will keep soaring speeding the future and become the No 1 choice of new operators in explor
23. orted Start URL Download HTTP Download method When using http to upgrade firmware it will check firmware version before starting download process In Filename field press Browsing Button Press Start HTTP Download button to start downloading file If firmware version doesn t fit in with old version it won t allow updating 9 8 Advance Setting Hore WERA EI Fxos rede AN LAN Local dial number Locat diat prene BIP In Prefix outprenef OS aan Name Digits for matching Operation Digits for operation AdvanceSet i DigtMap aope O System O DigitMan2 aamnpe id Configuration Digitan3 a sid Logout O Digitans dropped Reboot a DigitMaps Ss roppea Cd DigitMaps Ss cropped sid DigitMap7 aanpe sid DigitMans droppead sid notice The fields must be setto null if this field will do nothing use as a quick dial function useasa quick dial function C To enable to be recognized as dial number L To enable to be recognized as dial number Save SIP Settings Dial Plan such as 12 1 1 6 DigitMap T For the No prefixed with 13 013 will substitute eg when call 1368644111 the send no will be 01368644111 Page 26 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Digit Map 2 For the No prefixed with 8 07558 will substitute oF a E But due to the setting of Digit Map 1 amp Digit Map 2 this rule exclude
24. r address and will respond to the query and the appropriate domain name of the network If you wish to specify a special SIP domain name you may enter the domain name here If no domain name is entered the SIP domain name will be set to that of the network i e that which is obtained via DHCP or specified on the LAN settings page section 2 3 2 The currently provisioned SIP Server and Domain are displayed beside SIP Server Settings for informational purposes Select whether or not to send a Registration Request to the SIP server by checking the box next to Send Registration Request For the endpoint set the dial plan to be used by all lines refer to Appendix D for details on the dialplan representation and select the transport method to be used for SIP signaling either UDP or TCP For each line on the endpoint NOTE The IP Phone has a single line enter the Line Phone Number Caller ID Name signaling port value authentication Username and Password and select if AEC is to be performed on this line Press Save SIP Settings to save the new values Extensions Page 17 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual eros A emee Home 76ner Extensions User 1 Sip Book DOB Signalling ToOsiLimsery Lone rig WAN LAN C Support PRACK method with provisional response reliability SJP Encode SIP URI with user parameter CODECS Session Timer use UPDATE method C Disable
25. re Defaut Factory This page is used to restore configuration values of system settings from a previously saved configuration file or default factory values that stored inside the device Restore configuration from a file Click Configuration item on the top menu Click Restore item on the left menu Press Browsing button to select file by backup from local machine Press Start Download button to process downloading file After downloading file is finished the web system will redirect to restart device Restore default factory values form device Click Configuration item on the top menu Click Restore item on the left menu Press Start Restore Default Factory button After restoring default factory the web system will redirect to restart device 10 Dial Model 10 1 Direct Dial Dial through VolP No Directly pick up telephone receiver connected with FXS port and then dial telephone No Page 29 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 11 Troubleshooting 1 Confirm all cables are connected properly 2 Check whether there is the connection through Ping action of PC 3 Connect the gateway to the LAN interface and check whether the gateway is set properly 4 If the fault cannot be solved yet please contact the technicians 12 Dial Plan And IVR 12 1 1 Dial Plans The H 323 and SIP code will allow provisioning via web browser of the dial pla
26. s One 10 100 BASE T WAN port used to connect broadband data network One 10 100 BASE T LAN port bridged to the WAN port 2 analog loops starts the FXS interface RJ 11 used to connect 2 telephones Supporting DHCP Client or static IP address allocation plan Supporting 802 1Q VLAN and VLAN Tag Mute compression and comfort tone generation technology ensure clear conversation quality Self adaptive jitter cache ensures smooth voice function Lost packet compensation guarantee mechanism provides a better voice quality Built in Internet gateway function Supporting NAT Network Address Translation and NAPT Supporting DHCP Server used for the dynamic address allocation plan of LAN devices Built in PPPoE client used for broadband access user authentication Easily configured Console port Supporting remote configuration of Web mode and remote software downloading upgrading 5 Performance Indices Description of Product Model IAD 2 FXS 2 port IP voice gateway SIP protocol Physical Specifications Size 113mm L x 90mm W x 28mm AC DC power adapter 12V DC Power supply DC input 12V DC 1A Weight About 0 15 kg Page 5 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual oe System availability gt 99 999 MTBF gt 100 000 hours MTTR lt 5 Reliability min Ambient requirements 5 95 non condensing Voice compression algorithm G 729 G 723 and G 726 Analog voice port FXS 2 ports
27. s Page 18 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Home Server Extensions User 1 User 2 Sip Book OOB Signalling TosDiffsery Tone Ring WAN LAN User 1 Configuration SIP WNES Line 1 Fhone Number Caller Name Fot AEC On UserName Password Register State vances pve I Download Configuration Line1 Gain Control LogQut Reboot Inout Gain Control 12 18dk db Output Gain Control 612 18db db Save SIP User Settings This sub page and the next User2 sub page allow the user to configure the device with phone number caller ID username and password specified by the service provider Home Extensions User User 2 Sip Book OOB Signalling TosDitts er Tone Ring VLAN WAN LAN User 2 Configuration SIP CODECS Line 2 Phone Humber Caller Mame Fot AEC On UserName Password Register State AdvanceSet Primary Server 900508 900508 5060 om 900508 eet Secondary Sever 00 v O o L Download Configuration Logdut Reboot eboo Input Gain Control 612 18dh 2 dk Output Gain Control t12 18db db Save SIP User Settings Line Gain Control Home WAN LAN RTP Telephone Event Configuration SIP G CODECS Send DTME Events he UI et REC 29272 signalling using payload value Zz O Regenerate DOB OTMF tone Extensions User 1 Sip Book OOB Signalling TosiDiS er Tone Ring System Download configuration f Save OOB Settings LogQut Reboot This sub page allows configur
28. ss automatically f Use the following ONS server addresses Preferred ONS server aD 96 134 133 Advanced Alternate DNS server Cancel Fig 1 8 2 WAN Configuration Environment R Configure the TCP IP Protocol of PC according to Fig 3 with the PC and WAN interface in the same network segment R Configure the device according to Fig 4 m Use straight through cables in the figure R After configuration input the IAD default IP address in IE address bar Each IAD will be allocated with an initial Wan IP address before delivery assumed to be 192 168 1 200 Page 9 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Internet Protocol TCP IP Properties General TOU can getlP settings assigned automatically if your network supports this capability Othenwige you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 12 766 7 115 Subnet mask 255 255 295 0 Default gateway 12 168 1 1 C Obtain DHS server address automatically f Use the following ONS server addresses Preferred ONS server eU2 96 134 133 Advanced cence Alternate DNS server Fig 3 Fig 4 Page 10 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 9 Configuration in WEB Mode 9 1 L
29. ter buffer For an adaptive jitter buffer choose the maximum allowable playout delay in milliseconds For a fixed jitter buffer choose the fixed playout delay in milliseconds Finally select whether or not a decoder should automatically switch from an adaptive jitter buffer to a fixed jitter buffer upon fax modem tone detection Adaptive jitter buffers are sometimes detrimental to fax transmission over G711 CODECs if they have to adapt too rapidly or too extensively due to inconsistent and widespread packet delays In these adverse network conditions a fixed jitter buffer provides superior performance when handling incoming fax transmissions over G711 CODECs Press Save CODEC Settings to save the new CODEC parameters Page 22 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 9 6 System Setting Home S Security Timedut Localization Handset SNMP Service ACCE 9 WAN LAN Set Security Password SIF CODECS Password is currently installed AdvanceSet System Account admin Download Sines won Configuration Mew password fe Reboot Change Password 1 Set Security Password Click System item on the top menu Click Security on the left menu In Old password field input old password if you have it In New password field input new password In confirm password field input confirm password Press Change Password button to save changes Home Security TimeOut Loca
30. to the device If you wish to download the new firmware image using TFTP enter the filename of the ROM image and enter the IP address of the TFTP server on which this file resides To initiate the TFTP download process press Start TFTP Download If the ROM image is stored on the same local machine you are using to access the device s web pages you can choose to download the ROM file to the device using an HTTP post Enter the filename of the ROM image or press Browse to help locate the file To initiate the HTTP download process press Start HTTP Download If the main application is executing at the time the device will automatically reboot itself into the downloader mode and begin the download process If the downloader application is executing at the time the download process will begin The download status will be displayed when the image download process is complete Please refer to Section A The Downloader Application for more details on the download process Page 25 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual Home Download AutoUpdate WAN LAN SIF TFTP Download method Select remote TFTP server IP address and filename CODECS TFTF Server IF ice eee System Ae Start TFTP Download Download Configuration Say HTTP Download method Select filename on local browser machine Reboot z Start ATTP Download URL Download method Currently tpw http and hits are supp
31. uration of the WAN interface status settings The default WAN interface IP address is set to 192 168 1 200 Please note that any actions modifications which alter the topology of the Ethernet Bridge will result in the spanning tree protocol to relearn During this relearn period may take up to one minute HTTP access will be unavailable on all bridged Page 12 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual interfaces including the LAN interface On this sub page you can specify whether the WAN interface is to use PPPoE and configure the PPPoE client First select whether PPPoE is enabled or disabled If enabled enter the username and password required for the login authentication process Home WAN Status WAN Setting PPPoE IPSEC VLAN MAC Spoofing WAN LAN WAN PPPoE Configuration SIF CODECS Enable PPPoE No System Authentication Download Username nl Configuration Password Ge LogQut ne Reboot Settings Idle Timeout o minutes Echo Timeout o seconds Echo Count b service Mame fe Save PPPoE Settings MP Setting the idle timeout will result in the PPP connection being torn down if the client detects inactivity on the connection over the specified timeout period Leaving this field blank will result in the connection being permanently up i e without timeout Setting the echo timeout will result in the PPP connection to send the echo request t
32. used by VolP call signaling RTP packets HTTP and SNMP All reserved unavailable ports will be displayed on this page Page 16 of 32 WINDTOWER INFORMATION TECHNOLOGIES CO LTD WT 3202 Gateway User s Manual 9 4 SIP Configuration Home Server Extensions User Sip Book OOB Signalling ToS DiS ery Tone Ring VLAN WAN LAN CG UTSnL Serer sip ezdk net 5060 Domain sip ez gk net Current Server 0 Domain 3 sis Address sip ez gk net PorFaDN Address ep or Foo TORNETS Port Port aa System 7 Ceres 3500 l l ae ronnie send Registration Request with Expire Time Send Registration Request with Expire Time DES Configuration Outbound Proxy IF es PF or FGD Outbound Proxy IP IP or FADN LogMut Outbound Proxy Port a Outbound Proxy Port Reboot RTP Port Number Setting 5000 65535 E HAT Traversal Settings NONE O UPnP Control Point E STUN Server IP f F or FAD STUN Server Part K Leaving a setting blank will force the unit to use the information obtained wia DHCP andor DNS This page allows configuration of the SIP server and endpoint settings Enter the address and port value of the SIP server The address may be an IP address or the name of the server If no SIP server address is entered the device will attempt to self provision a SIP server using a DNS query For this to be successful ensure that the DNS settings on the device include a DNS server address which is configured with the SIP serve
Download Pdf Manuals
Related Search