JCUP QD3800 Manual
Contents
1. is space is enter In the POWER ON box input POWR _ 1 Od Remarks There are spaces after POWER Od is enter Input other codes in the same way c If the data is in the numerical value and character format then synthesize the above mentioned formats 3 Once done click Add to add your projector model then Click Send Afterward click Now you can use the visualizer to control your projector 4 Connect the visualizer s projector control port to the RS232 port with a RS232 cable Please disconnect the computer from the RS232 port first Then use buttons on the operation panel to control the projector The visualizer provides a 6 pin to 9 pin RS232 cable If this cable does not match to your projector s RS232 port an additional RS232 cable is needed This additional RS232 cable can be made based on the pin location of the projector s RS232 control port The pin locations of the visualizer are the pin 1 is RXD Received Data the pin 5 is TXD Transmitted Data the pin 4 is GND Ground Other pins are not defined The pin location information of the projector is provided by the projector s manufacturer The projector s RS232 control port normally has RXD pin TXD pin and GND pin the name may be different The parallelism of each data pin is shown as follows Visualizer s RXD pin Projector s TXD pin Visualizer s TXD pin2. Projector s RXD pin Visualizer s GND pin Projector s GND pin 5 If you can not use buttons on the operation panel to control the projector please use Code Writing software s projector control code testing function to check if the control code is correct Click Projector button the following dialog box appears as below PROJECTOR SETUP Name E PowerOn PWR ON 0d 0a PowerOff PWR OFF Od Oa SOURCE 11 SOURCE 21 SOURCE 41 Input4 f SOURCE 42 Input5 BAUD RATE 9600 PARITY No Pariz ADD DELETE SELLEGI TEST Connect the visualizer to a computer with a RS232 cable Please disconnect the projector from the RS232 port first and select the Baud Rate and Parity based on the projector s Baud Rate then click the TEST button to pop up the Projector Code Test dialog box input the Baud Rate and Parity based on the projector s Baud rate then click Open 19 PROJECTOR SETUP Name Canon LV7350 PowerOn C00 Od Oa Power0ff BAUD RATE 9600 v PARITY No Par Input 1 Input2 Click the projector control buttons on the visualizer s operating panel to check if the control code that the program received is the same as the sending code If the receiving code is same to the sending code the input codes are correct If the visualizer can not control the projector please do the following 1
3. WORKING WITRUNEGATIYV ES 11 FOCUSING ee rane 12 FREEZING IMAGE rsispa e a re E E R E O E 12 BRIGHTNESS 405 aeai TH ng ng a 12 WHITE BALANCE ADJUUSTIMENT HH 12 HC II 6x06 0140x6 062x606 dae 06a 6anl di 12 TEX IMAGE 12 COLOR AND B amp W MODE SWITCH 12 WE TS 13 ROBINP UTS 13 PROJECTOR ONS TAND BY ects 13 PROJECTOR INPUTS SELECTION otoceni E E Ea 13 IMAGE ROTATION cierres se dna 13 IMAGE REVERSION n a AN n 13 INFRARED REMOTE CONTROL E 14 AXA MULTIPLE SCREEN DISPLAY 14 INSTALLING VISUALIZER SOF WAREL 14 15 SB IMAGE CAPTURE 15 CONTROLLING VISUALIZER BY 16 CONTROLLING PROJECTOR BY 17 FOCDING THEUN 1s s2 se 20 SE COINS 22 PARTS IDENTIFICATION Camera Arm lights Button instruction Connectors Operation panel CONTROL PANEL CAMPC1 PC2_s vIpEovIDEO J CO PowER we Rot Rotate the image Frz Freeze the image Neg Display film negatives Text Switch between image text mode Save Save captured images Title Freeze the top 1 8 of the screen
4. 1 02 22 15 frames sec Dimension Wx D x H N W 5 5Kg 12 11 Weight an Pa G W 9 5Kg 20 9 Ibs AC power cord RGB cable Audio Video cable S Video cable Computer RS232 cable 9 pin to 9 pin Projector RS232 cable 6 pin to 9 pin Accessories cane HDMI cable Audio convert cable AC adapter User s manual Software CD Infrared remote control Warranty card Design and specifications are subject to change without prior notice 23 QOMO HITEVISION LLC Toll Free 1 866 990QOMO E Mail info qomo com Web www qomo com
5. Check to see if the source control codes of projector are correct 2 Check to make sure the connection between the visualizer and the projector is correct FOLDING THE UNIT 1 Fold the right arm light down first onto the base then the left arm down Rotate the camera head clockwise until the camera head is parallel to the camera stand aS gt lt gt 20 2 Carefully fold the camera stand down to the front panel Cautions a Do not lay the unit down flat b Do not try to stand it on its rear or sides c Do not try to pick up this unit by pulling the camera stand od NOT THIS WAY 21 SPECIFICATIONS Resolution Total Pixels Lens Motorized Camera Head Camera Rotation Focus White balance Negative positive conversion Black white and color selection Split Image Image Title Image Freeze Image Rotate Image Save amp Recall 128 frames saved in flash ROM 4 x 4 multiple screen display _ RGB DB15FLC Operating system Hardware Requirement CPU higher than P2 4GHz Memory higher than 256 MB 1 2 1 1 1
6. SOFTWARE This function is to snap and display images with the USB interface which includes displaying static and dynamic pictures snapping dynamic images and playback the dynamic images with the Windows Media Player or its own player Insert the CD ROM that comes with the visualizer into the CD ROM drive lf Autorun is enabled on your system then the Software Setup window will be displayed automatically as below If it does not start automatically after inserting the CD ROM Click Start 14 gt gt Computer and double click Pat the CD ROM drive letter might be different in different computer systems and then the above screen will appear immediately B Click the Install Capture Program button to install the program that captures images in the AVI or JPG format C Click the Install Code Writing Program button to install Code Writing Program D After the installation is finished then click the Exit button to exit the Software Setup window E Shut down your computer when prompted in order for the changes to take effect F Use the USB2 0 cable provided to connect your computer to the visualizer before your computer is restarted USB PORT The USB port can be used to store still images from the visualizer in a computer Connect the visualizer to your computer with the supplied USB cable The visualizer software is available on the supplied CD ROM Please pay attention to the following 1 Comp
7. Split Split Image function Mem Multiple Screen Display the stored images will be displayed in a 4 x 4 matrix Ppw Control the projector On Standby 3 Pin Projector input signal selection tv Move the image up down POWER Control the visualizer On Off CAM PC1 PC2 CAM RGB input signal selection S VIDEO VIDEO S Video Video input signal selection LAMP Control the arm lights and back light AUTO To auto white balance and auto focus T W Zoom in and out BUTTON INSTRUCTION Button Instruction Indicator Instruction Fold Setup Instruction Freeze __ Negative Positive _ Move the cursor u Image Text mode O O O OO Delete the image CAM PC1 PC2 S Video Video Rotate Freeze the Top 1 8 of the n ce Split Screen Move the cursor left Confirm Image save Move the image up en Cp Move the cursor right Image recall Move the image down POWER l xit Auto Adjust Color Projector power on standy Projector input select Brightness and Focus Move the cursor down iteVision Notes Image recall function Press and Hold Two Seconds Light Control amp to Power Off Visualizer Side Lights Back Light Lights Off DIGITAL MEDIA SOLUTION REMOTE CONTROL PROJ ECT OR POWER INPUT POWER Control the visualizer On Off SAVE Save captured images RECALL Multiple Screen Display LAMP Control the arm lights and back light Press the button more than 5 seconds to d
8. adjust the white balance automatically AUTO ADJUSTMENT One of the visualizer s special functions is auto adjustment Press AUTO button to auto adjust the white balance and the focus TEXT IMAGE MODE Press the Text button to switch between image text modes To display a text file switch to the text mode to get a clearer text effect COLOR AND B amp W MODE SWITCH Press B amp W once to enter the Black amp White mode press again to return to the Color mode On the remote control 12 VIDEO INPUTS Press the S VIDEO VIDEO button to switch between S Video and composite video signals RGB INPUTS Use the CAM PC1 PC2 button to switch between Camera and different RGB signals Each time the CAM PC1 PC2 button is pressed it provides seamless transitions among different sources such as Camera COMPUTER IN and RGB IN Notes RGB OUT always outputs RGB IN signals PROJECTOR ON STANDBY Press the POWER button to turn on the visualizer s power and press the button to turn the projector power on To place the projector on standby after the use press the Ppw button and hold for more than 2 seconds Using the remote control press the PROJECTOR POWER button PROJECTOR INPUTS SELECTION When the projector is connected to several input sources use the Pin button to switch between projector signal inputs Using the remote control press the PROJECTOR I
9. off ADJUSTING IMAGE SIZE To reduce or enlarge the image size displayed on the screen press the OT Zoom in We Zoom out button WIDE TELE WORKING WITH NEGATIVES The visualizer is automatically set to display normal materials on the screen when the power is on To display negatives turn on the backlight by pressing the LAMP key and then press the Neg button to display the film negatives Press the button again to display normal materials in the color mode g Positive Negative SSBB BEEBE ee FOCUSING When the visualizer is turned on the focus automatically adjusts to the stage Only 3D objects require a focus adjustment Press the AUTO button to auto focus Press the FAR or NEAR button to focus manually FREEZING IMAGE To show a still image on the screen when the output signal is RGB press the Frz button The frozen image cannot be adjusted Zoom in out color adjustment etc BRIGHTNESS ADJUSTMENT If the image effect is not satisfactory can adjust the brightness to get a better image effect Use the BRIGHT or BRIGHT button to adjust the brightness To increase the brightness press the BRIGHT button To decrease it press the BRIGHT button WHITE BALANCE ADJUSTMENT Each time the lighting condition changes the user should adjust the white balance of the camera Press the AUTO button to
10. I format C Set the Frame Rate Click Capture gt Set Frame Rate and click open Choose Frame Rate to set the frame rate D Set Time Limit Click Capture gt Set Time Limit to set the time limit while capturing video E Note Do not connect disconnect the USB cable when the application is running which will cause the program to be interrupted CONTROLLING VISUALIZER BY COMPUTER You can control the visualizer from a computer connected with a RS232 connector 16 gt Connect the computer and the visualizer using the RS232 cable B Double click X 232 Control Control Panel you can open this file from the CD and double click it or copy this file to any directory on your computer s hard drive and double click to launch it CONTROLLING PROJECTOR BY VISUALIZER The code writing software is used to inputting projector s control code then can control various projector with the visualizer 1 Connect the visualizer to the projector with the RGB VIDEO S VIDEO cables 2 Connect the RS232 cable to the computer s connector The visualizer s RS232 port is located on its right side 3 After completion of the connection turn on the visualizer click start gt All Programs gt Visualizer gt Visualiser Codetriting the following dialog box appears as below When the indicator of Current RS 232 Connection Status is green that means the connection between the visualizer and th
11. NPUT button IMAGE ROTATION In order to rotate the image press the Rot button once the displayed image will be rotated clockwise Continue to press the Rot button to restore the image to its initial position IMAGE REVERSION To display a vertically mirrored image press the MIRROR button Press the MIRROR button again to exit 13 INFRARED REMOTE CONTROL The visualizers remote control can control the camera from different angels On the left side of the visualizer stage there is a built in remote control storage compartment where you can store the remote control when it is not in use Please note that an infrared remote control can only be used up to a certain distance to the unit Objects situated between the visualizer and the infrared remote control and a weak battery may interfere with the reception 4X 4 MULTIPLE SCREEN DISPLAY Press the stored images can be displayed 4 x 4 matrix Press the stored first sixteen images be displayed 4 x 4 matrix Use Neg D A button to Select the image that you want to display then click button to display the selected image press button to delete the selected image Press CW to exit the 4 x 4 image display mode On the remote control the RECALL n aie 9 gt 9 button can do the operation Press EXIT to exit the 4 4 image display mode INSTALLING VISUALIZER
12. OC view Visual Presenter Owner s Manual Model QD3800 PRECAUTIONS WARNING Risk of shock Dangerous voltage inside Please follow these precautions To prevent fire or shock hazard do not expose the unit to rain or moisture To prevent electrical shock do not open the cabinet Refer to qualified personnel for service only Do not use the unit continuously for more than 24 hours with camera auto focus on It may cause damage to the camera lens Be careful not to spill water or other liquids onto the unit or allow combustible or metallic objects to get inside the cabinet Unplug the visualizer from the wall outlet when it is not in use for an extended period of time Clean cabinet with a soft cloth lightly moistened with a mild detergent Clean lens carefully with an air spray or soft dry cloth to avoid scratching When lamps flash or become dark they should be replaced with new ones Avoid interchanging arm lights and back light frequently Remove the camera lens cap before power the unit on CONTENTS PARTSAIDENTIFICGATION 3 CONTROL BUTTONINSTRUC TION 4 REMOTE 4 CONNECTIONS R 6 BASIC PREPARATIONS 6 PALIN ISS VIDEO OUR 10 VVORKINGCON THE 10 WORKING OUTSIDE THE STAGE RE 10 11 ADJUSTING IMAGE 11
13. access this function Step 3 Connect to a desktop computer Note You can connect a laptop computer to the RGB IN port of side panel using a RGB cable Rear Panel Step 4 Connect to the first video equipment with S Video input In the step 2 the connection between the S video and C Video output signals to the projector was established where the RGB cable runs from the visualizer and goes to the projector Once the connections have been made as detailed in the steps 2 3 4 input signals from the computer visualizer camera C Video and S Video are going to the RGB1 input on the projector and will be displayed on the projector screen as RGB1 These signals can be seen in turn when pressing 1 2 and S VIDEO VIDEO on the control panel of the visualizer S Video Cable S Video out Projector or amplifier speaker equipment Step 5 Connect to the second video equipment with video input Video Cable Jo oo Projector Color monitor Pm Video in Step 6 Connections for external control from the computer Side Panel PROJECTOR MIC USB RGB IN AUDIO IN 5232 RS 232 cable USB cable JRS 232 connector of
14. e computer s RS232 connector is good If the indicator is red please check if the RS232 cable is connected correctly When all the cables are connected correctly please click Projector to select your projector model under the drop down list then click Send If you can not find your particular projector model in the Projector please do the following 17 1 Select Baud rate and parity and input the projector control code The baud rate parity and control code is supplied by projector s manufacturer please refer to the projector manual PROJECTOR SETUP Name EPSON EPS 820 811 Power0n PWR ON Od 0a PowerOff PWR OFF Od Oa SOURCE 11 0d Oa P SOURCE 21 Od 0a SOURCE 41 0d 0a SOURCE 42 0d 0a BAUD RATE 9600 PARITY No Pariz ADD DECHIE SELECT TEST The input format of projector s control code is as follows a If the data is in the numerical value format please input data directly block them off with comma do not distinguish lowercase and uppercase For example the POWER ON code in Hitachi projector manual is In the POWRE ON box lnput be ef 03 06 00 ba d2 01 00 00 60 01 00 Then use the same input rule to input other code b If the data is in the character string format input character string For example the POWER ON code in the SHARP C40 50 projector manual is jt
15. elete all pictures stored in the Flash ROM ROTATE Rotate the image FREEZE Freeze the image NEG Display film negatives MIRROR V Reverse the image XGA Toggle among XGA 1024 x 768 SXGA 1280 x 1024 WXGA 1366x768 720P 1280 x720 1080P 1920x1080 TEXT Switch between image text mode B amp W Switch between Color mode and Black amp White mode TITLE Freeze the top 1 8 of the screen SPLIT Split Image function PROJECTOR POWER Control the projector On Standby PROJECTOR INPUT Projector input signal selection EXIT Exit selected function TELE WIDE Increase and decrease magnification FAR NEAR Focus near or far AUTO To auto white balance and auto focus CAM PC1 PC2 CAM RGB input signal selection S VIDEO VIDEO S Video Video input signal selection VOLUME Increase or decrease the volume RED Increase or decrease the red hue BLUE Increase or decrease the blue hue BRIGHT Increase or decrease the brightness SCROLLT Move the image up down CONNECTIONS Rear Panel IN B SVIDEO N AUDIO wpEo AUDIOIN Side Panel 15 PROJECTOR MIC USB RGB IN AUDIOIN RS232 1 12V IN 2 AUDIO OUT 3 VIDEO OUT 4 S VIDEO OUT 5 VIDEO AUDIO IN 6 VIDEO IN 7 S VIDEO AUDIO IN 8 S VIDEO IN 9 PC AUDIO IN 10 HDMI Connector 11 PROJECTOR Connector 12 COMPUTER OUT 13 COMPUTER IN 14 PROJECTOR RS232 Connector 15 MIC IN 16 USB Co
16. nnector 17 RGB IN 18 RGB AUDIO IN 19 COMPUTER RS 232 Connector BASIC PREPARATIONS 1 Place one hand firmly on the base of the visualizer while carefully lifting up the camera stand using the other hand Camera Stand 2 Open the arm lights and rotate the camera head until they are properly positioned Arm lights t 3 Making connections Before making any connections turn off all the power Please ensure that the visualizer along with all other equipments to be connected are turned off Step 1 Connect power source First connect the power cord to the 12V IN connector Step 2 Connect to the projector Rear Panel Connect the PROJECTOR port to the projector s RGB IN port using the RGB cable You can also control a projector using the controls on the visualizer by connecting the projector to the visualizer using a 6 pin to 9 pin RS232 cable Some projector models may require a converter cable in addition to this standard RS232 cable to connect to the projector control port for the pin locations and shape of some projectors control port connector may be different from the connector of a standard RS232 cable Once the visualizer is connected to the projector you can control the projector s power on standby and input selection by using the visualizer Aside from Hitachi projectors the Code Writing program that comes with the visualizer is required to
17. the computer T USB connector of the computer 7 Use the computer RS232 cable 9 pin to 9 pin to make the connections displayed below to control the visualizer from an external computer A USB connection enables the computer to capture still images and or 9 video streams from the visualizer Special software is required for this operation 4 Turn on the power by pressing the POWER button PAL NTSC VIDEO OUTPUTS The S Video and composite video outputs are set to PAL NTSC during manufacturing WORKING ON THE STAGE 1 Place your material on the platform 2 Select the enlargement required using the T and W buttons 3 Adjust the focus using the Near and Far buttons or AUTO button WORKING OUTSIDE THE STAGE To show a 3 dimensional object using the visualizer place the object on the working surface and adjust the T or WQ and AUTO keys If the object is too large for the stage or if you would like to show it from one of its side or a different angel just place the object behind or in front of the unit and manually tilt the camera head remove the close up lens prior to titling the camera head Rotate 330 degrees vertically LIGHT The arm lights are powered on when the power is turned on Each time you press the LAMP button the lighting changes occur as demonstrated The arm lights turn on The back light turns on All the lights turn
18. uter hardware requirement CPU 2 4GHz RAM 256M or above Graphic card 64M USB 2 0 port Hard disk 40G or more Monitor display resolution higher than XGA 1024x768 2 Operating system Windows SP2 Win7 3 Must use a high speed USB 2 0 cable provided 4 When connecting the visualizer to a desktop computer with the high speed USB 2 0 cable provided we recommend using the USB port located on the rear of the mainframe The USB port on the front of the computer might have interference USB IMAGE CAPTURE You can capture and control images on the visualizer from a computer connected with a USB connector 15 Click Start gt Program gt VideoCap gt VideoCapx xx X XX 16 software s version to open the software A Static Images Snap Click Capture gt Capture Frame input the file name in dialog box or you can click 8 icon on the toolbar then input file name in dialog window The image file is JPG format B Snap Video Stream Click Capture Start Capture input the file name in dialog box or click P icon on the toolbar then input the file name in dialog box If you want to set the time limit for the capture select Capture gt Set Time Limit to set the time limit Click Start Capture to start capture and click Stop Capture or icon on the toolbar to stop capture If you have set the time limit it will stop automatically when the time is up The video file is AV
Download Pdf Manuals
Related Search