USER`S MANUAL
Contents
1. INSTALLATION INSTRUCTIONS Installation Procedure The OXIC XFO 1013TRS video transmission systems series are preset for immediate use There are indicator LEDs on the units for monitoring the real time status of video data and power The following instructions describe the typical installation procedure and the function of the LED indicators located on each unit 1 Connect the video source camera to the video input BNC connector on the transmitter unit using coaxial cable 2 Connect the video output BNC connector on receiver unit to the video monitor using coaxial cable 3 Connect the fiber optic cable between the transmitter and receiver 4 Apply the power supply to both the transmitter and receiver 5 When the power is applied the orange POWER LED will light indicating the presence of operating power The blue VIDEO LED and the blue DATA LED will give an indication as stated in the following page 6 The system should now be operational System Terminal Block Connections The various input and output connections for OXIC XFO 1013TRS Series system are as follows Video Input or Output BNC Connectors Data RS 485 Connection Terminal No 1 RS 485 Terminal No 2 RS 485 Terminal Block for Data Connection Camera Site Connect the Terminal No 1 Q in the terminal block for data connection to RS 485 of the controlled unit pan tilt dome and connect the Terminal No 2 in2. are normally on unavailable and DATA 1 blink at the rate of the operating data As shown in the diagram in the following TRANSMITTER and RECEIVER Power ON Orange Indicates that correct power has been applied Transmitter Video OFF Indicates no video detected on input BNC connector No Video present on input BNC ON blue Indicates video detected on input BNC connector Video present on input BNC Data DATA1 OFF Indicates no data detected on the transmit data cable Blinking Blue Indicates data transmitted at the rate of the operation data OPT VID IN DATA AUDIO PWR VID Pa ca i a DATA1 DATA3 DATA2 _ DATA gt Front Panel of XFO 1013TS Transmitter Audio RJ 45 Port is expandable for audio tranmission Receiver Video OFF Indicates no video present on output BNC connector No Video present on output BNC ON Blue Indicates video detected on output BNC connector Video present on input BNC Data DATA1 OFF Indicates no data detected on the receive data cable Blinking Blue Indicates data received at the rate of the operation data OPT VID OUT DATA AUDIO PWR VID x Da Dan DATA1 DATA3 DATA2 DATA4 Rear Panel of XFO 1013RS Receiver Audio RJ 45 Port is expandable for audio tranmission TROUBLESHOOTING Optical Fiber The OXIC XFO 1013TRS Series is available with most applications using multimode or single mode optical fibers Please be certain tha
3. TRANSMITER AND RECEIVER PAIR SINGLE MODE XFO1013TRS SERIES TRANSMITER XFO1013TS XFO1013TM RECEIVER XFO1013RS XFO1013RM 1 CHANNEL DIGITALLY ENCODED VIDEO 1 CHANNEL BI DIRECTIONAL DATA MULTIPLEXER USER S MANUAL Table Of Contents General Information iii PP eaa Technical Specifications 22 ccccccesseeeeeeeeeeeeeeees Installation INSUUGHONS iaa Installation PFOCEOUFE ii System Terminal Block Connections Indicator EE Ds coa ne iti re len Tee le DEE Limited War any iii GENERAL INFORMATION Introduction The OXIC XFO 1013TRS Series video and data transmitter and receiver support simultaneous transmission of one channels of 8 bit digitally encoded video and one channel of bi directional data over one multimode and single mode optical fiber The modules are universally compatible with major camera systems and support RS 485 and RS 232 data protocol Plug and Play design ensures the ease of installation and electronic and optical adjustments are never required Model Number Unit Type Model Number One channel Digitally Encoded Video One channel Data Transmitter XFO 1013TS One channel Digitally Encoded Video One channel Data Receiver XFO 1013RS Technical Specifications VIDEO Video Input 1 volt pk pk 75 ohms Input Output Channels 1 Bandwidth 5 Hz 8 MHz Bit Resolution 8 bit Differential Gain lt 2 Differential Phas
4. e lt 0 6 Tilt lt 1 S N Ratio 67dB Weighed DATA Data Interface RS 485 RS 232 Data Channel 2 Data Rate 100Kbps Bit Error Rate 10 WAVELENGTH OPTICAL EMITTER NUMBER OF FIBERS CONNECTORS Optical Video Data GENERAL Power Supply Size Construction MTBF Operating Temp Storage Temp Relative Humidity INDICATOR Module Blue Blue Orange OPTICAL POWER BUDGET 850 1310nm Multimode 1310 1550nm Singlemode Laser Diode ST BNC Shield RJ 45 Plug DC12V 600mA 195mm x 191mm x 36mm Aluminum gt 100 000 hours 30 C to 50 C 40 C to 85 C 0 to 95 no condensing Video Sync Present Data Sync Present Power On Optical transmission distance is limited to optical loss of the fiber and additional loss caused by connectors splices and patch panels Fiber Wavelength Transmitter Receiver Optical Max Model Output Model Sensitivity Power Distance Budget Singlemode 1310nm XFO XFO 1013TS 5 dBm 1013RS 26 dBm 21dB 30km CAUTION The transmitter unit contains a laser emitting diode located in the optical connector This device emits invisible infrared electromagnetic radiation that can be harmful to human eyes The radiation from this optical connector if viewed closely without any protection may cause instantaneous damage to the retina of the eye Direct viewing of this LED should be avoided at all times
5. ntact our Customer Service Department for further assistance LIMITED WARRANTY Tiandy Tech guarantees two 2 year repair at no charge and lift time maintenance at prevailing rate from the date of delivery Tiandy Tech series products are warranted to be free from defects in materials or workmanship for one year from the date of retail purchase We reserve the final right to judge the malfunction of the products What is not covered by this warranty Over one year warranty period e No warranty maintenance for appearance failure e Damage incurred in transportation loading amp unloading or carrying e Damage resulting from any product modification alteration or adjustment not authorized by Tiandy Tech e Damage from misuse abuse accident and unsuitable physical and operating environment e Maintenance of the accessories such as fuse one off battery etc e Damage from acts of God such as fire earthquake lightning flood etc Tiandy Tech reserves the right of final interpretation and modification to the above items All the warranty information stated above is subject to change without notice
6. t the correct size and type of the fiber is being used for the particular mode transmitter receiver combination Also be certain that the attenuation and bandwidth of the fiber optic cable being used is within the range of the system s loss budget specifications General Any dirt or dust may easily pollute or block the fiber from accepting or radiating light Therefore please try to keep the optical connector clear and always use the dust caps whenever the connector is exposed to air It is suggested that the tip of the optical connected should be carefully cleaned with a lint free cloth moistened with alcohol from time to time The status of any of the VIDEO LED should provide the first clue as to the origin of any operational failure If the VIDEO LED on the receiver unit is off it usually means that the fiber is broken or has too much attenuation Please also make sure that the transmitter and the receiver are not used in opposite position If the system is still not working after examining the above possibilities please contact our Customer Service Department for further assistance Data Link Even when installed exactly as directed it is possible that the data audio function may fail to operate properly If these problem occurs first please check the data cable then check whether the data cable connector is firmly inserted into the RJ 45 port If the system is still not working after examining the above possibilities please co
7. the terminal block to RS 485 of the controlled unit pan tilt dome Control Site Similarly connect the Terminal No 1 Q in the terminal block for data connection to RS 485 of the controlling unit Keyboard Controller Matrix DVR and connect the Terminal No 2 in the terminal block to RS 485 of the controlling unit Keyboard Controller Matrix DVR Data RS 232 Connection Terminal No 6 Signal being transmitted out over fiber Terminal No 7 Signal being received in from fiber Terminal No 8 Ground Terminal Block for Data Connection Camera Site Connect the Terminal No 7 232T in the terminal block connected from the transmitter to RS 232 232R port of the controlled unit pan tilt dome and Terminal No 8 GND is used for ground connection Control Site Connect the Terminal No 6 232R in the data cable from the receiver to RS 232 Port 232T of the controlling unit Keyboard Controller Matrix DVR and the Terminal No 8 GND is used for ground connection Indicator LEDs The stand alone units have integral LEDs that are used to monitor the state of the unit There are one video LED one power LED and four data LEDs on each unit One labeled as PWR lights when operating power is present Another labeled as VID lights when the video input output signals are detected The other one labeled as DATA 1 DATA 2 DATA 3 DATA 4 among them DATA 2 DATA 3 DATA 4
Download Pdf Manuals
Related Search