Home

4-Port ADSL/ADSL2+ Wireless Router User Guide

1. Destination IP Address Subnet Mask 255 255 255 255 Source Port Destination Port Enable Current Filter Table Rule Protocol Source IP Mask _ SPort _ s Dest IPMask _ _ DPort State Direction Action ermit i 234 181 93 2 255 255 255 255 192 168 2 33 255 255 255 255 enable Upstream The following items are displayed on this page Outgoing Default Action Sets the default filtering action for outgoing packets that do not match a rule in the filter table Default Permit maximum 32 entries are allowed Incoming Default Action Sets the default filtering action for incoming packets that do not match a rule in the filter table Default Deny maximum 32 entries are allowed D NorE The default incoming action denies all packets from the WAN port Rule Action Specifies if traffic should be permitted or denied Default Permit Protocol Specifies the destination port type TCP UDP or ICMP Default TCP Direction Specifies the packet destination Default Outgoing 95 CHAPTER 8 Services IP Port Filtering Source IP Address Specifies the source IP address to block or allow traffic from Destination IP Address Specifies the destination IP address to block or allow traffic from Subnet Mask Specifies a subnet mask Source Port Specifies a range of ports to block traffic from the specified LAN IP a
2. Displays the DHCP Client IP address MAC Address Displays the physical layer address of the DHCP Client 46 CHAPTER 4 Device Information WLAN Status Expiry s Displays the duration of the lease time Type Indicates if the entry is dynamic or static WLAN STATUS The WLAN Status window displays basic wireless interface settings Figure 14 Status WLAN WLAN Status This page shows some basic settings of wireless LAN WLAN Wireless Configuration Root Status Enabled 9 SSID SMC VAPO Disabled Wireless Client List T ERTE Tx Rate Power Expired MAC Address ib Packet Packet Mbps Saving CUT Current Access Control List Mode pisabled The following items are displayed on this page Wireless Configuration Indicates wireless interfaces that are enabled The router supports four multiple SSID interfaces Root and VAPO VAP3 Wireless Client List Lists all wireless clients associated to the router Wireless Access Control List Displays current wireless access control list settings E ET WAN STATUS CHAPTER 4 Device Information WAN Status The ADSL Router WAN window displays basic IPv4 and IPv6 WAN port settings Figure 15 Status WAN WAN Status This page shows some basic WAN settings WAN IPV4 Configuration Default e Interface VPINCI Encapsulation Rout Protocol IP Address Ga
3. LAN The LAN interfaces that can be grouped Interfaces Group The grouped WAN and LAN interfaces Apply Changes Sets the Interfaces Group as the selected group in the table 124 DIAGNOSTICS The Diagnostics page is used to test the local Ethernet connection or the WAN connection for the DSL signal and the connection to DSL provider network This chapter contains the following sections Diagnostic Test on page 126 Ping on page 127 Traceroute on page 128 ADSL Tone Diagnostics on page 130 129 DIAGNOSTIC TEST CHAPTER 10 Diagnostics Diagnostic Test The diagnostic test shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides Figure 74 Diagnostic Test Diagnostic Test The device is capable af testing your ADSL connection After selecting an interface click Run Diagnostic Test The result of each test item is listed below If a test shows a fail status click Run Diagnostic Test again to ensure that the the fail status is consistent Select the Interface Run Diagnastic Test The following items are displayed on this page Select the Interface Selects the WAN connection Default vcO Run Diagnostic Test Performs a diagnostic test on the LAN and WAN side connections LAN CONNECTION CHECK Displays the result of a test for connectivity on the LAN port Test Ethernet LAN Con
4. Proper space for heat dissipation is necessary to avoid any damage caused by device overheating The ventilation holes on the device are designed for heat dissipation to ensure that the device works normally Do not cover these ventilation holes Do not put this device close to a place where a heat source exits or high temperature occurs Avoid placing the device in direct sunshine Do not put this device close to a place which is damp or wet Do not spill any fluid on this device Please follow the instructions in the user manual quick install guide carefully to connect the device to your PC or other electronic product Any invalid connection may cause a power or fire risk Do not place this device on an unstable surface or support 10 COMPLIANCES PRECAUTIONS DE SECURITE Lisez attentivement les informations suivantes avant d utiliser votre appareil Respectez toutes les pr cautions afin de prot ger l appareil des risques et d gats provoqu s par un incendie et l alimentation lectrique Utilisez exclusivement l adaptateur d alimentation fourni avec cet appareil Faites attention la puissance de charge de la prise de courant ou des rallonges lectriques Une prise surcharg e ou des cordons et des fiches endommag s peuvent provoquer une lectrocution ou un incendie V rifiez r guli rement votre cable lectrique Si vous constatiez le moindre d faut remplacez le imm diatement Il es
5. Virtual Servers Virtual Server The page is used to configure virtual server So other users on the Internet can access the server on your LAN through the device Service Type Usual Service Name O User defined Service Name Protocol TCP v WAN Setting Interface v WAN Interface any v WAN Port M3 ex 5001 5010 LAN Open Port 113 LAN IP Address Apply Changes Current Virtual Server Forwarding Table ServerName Protocol Local IP Address Local Port WAN IP Address WAN Port State Action The following items are displayed on this page Service Type Sets a name to describe the virtual server service Usual Service Name Select a name from the list of common applications User defined Service Name Set a custom name to describe the service Protocol Specifies the port type Options TCP or UDP Default TCP WAN Setting Selects a WAN interface or IP address Depending on the selection either the WAN Interface or WAN IP Address setting displays WAN Interface Select the WAN interface for the virtual server WAN IP Address Specify the WAN IP address for the virtual server WAN Port Specifies the public TCP UDP port number or port range used for the service on the WAN interface Range 1 65535 LAN Open Port Specifies the TCP UDP port number or port range used on the local server for the service Range 1 655535 LAN
6. Annex M is an optional specification in ITU T recomendations G 992 3 ADSL2 and G 992 5 ADSL2 also referred to as ADSL2 M and ADSL2 M This specification extends the capability of commonly deployed Annex A by more than doubling the number of upstream bits Once enabled AnnexM increases upload speeds by the shifting the upstream downstream frequency split from 138 kHz up to 276 kHz allowing the maximum upstream bandwidth to be increased from 1 4 Mbit s to 3 3 Mbit s ADSL Capability ADSL Capability refers to means of manipulating the bit loading of a connection to increase quality of signal or transmission rate Bitswap Enables bit swapping Bit swapping is a way of swapping the bit loading of a noisy tone with another tone in the symbol which is not as noisy The bit loading from a specific tone can be increased or decreased In addition the TX power can be increased or decreased for a specific tone However there is no change in the overall payload rate after the bit swap operation SRA Enables seamless rate adaptation to set the optimal transmission rate based on existing line conditions 87 SERVICES The Advanced Configuration settings for the ADSL Router contain advanced system management configuration settings such as DNS setup routing configuration bridging SNMP and TR 069 settings The following sections are contained in this chapter DNS Settings on page 89 Access Control Lis
7. Enable Enable Disable Open System cae Shared Authentication Type Key Auto Apply Changes The following items are displayed on this page Enable VAPO VAP3 Enables up to four VAP interfaces on the router Default Disabled SSID Configures the service set identifier of a VAP on the wireless interface 67 WDS CHAPTER 5 WLAN Configuration WDS Broadcast SSID Enables disables the wireless interface to broadcast an SSID service set identifier to uniquely identify it on the network Relay Blocking Blocks traffic between SSID interfaces Authentication Type Sets the basic authentication method for the VAP interface Each access point radio interface can be configured to operate as a bridge which allows it to forward traffic directly to other access point units To set up bridge links between access point units you must configure the wireless Distribution System WDS forwarding table by specifying the wireless MAC address of all units to which you want to forward traffic Up to six WDS bridge links can be specified for each unit in the wireless bridge network Figure 30 WDS Configuration WDS Settings Wireless Distribution System uses wireless media to communicate with other APs like the Ethernet does To do this you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS Enable
8. DSL port may be defective gdi TROUBLESHOOTING Solution 9 9 Check the power outlet by plugging in another device that is functioning properly Check the power adapter with another router Verify that the router and computer are powered on Be sure the cable is plugged into both the router and the computer Verify that the proper cable type is used and its length does not exceed specified limits Check the network adapter in the computer and cable connections for possible defects Replace the defective adapter or cable if necessary Be sure the cable is plugged into both the router ADSL Splitter and an RJ 11 telephone jack Verify that the cable length does not exceed specified limits Check with your service provider for this information Check the cable connections on the router ADSL Splitter and wall jack for possible defects Replace the defective cable if necessary APPENDIX A Troubleshooting If You Cannot Connect to the Internet IF YoU CANNOT CONNECT TO THE INTERNET Check that your computer is properly configured for TCP IP For more information see Configuring the TCP IP Protocols on page 32 Make sure the correct network adapter driver is installed for your PC operating system If necessary try reinstalling the driver Check that the network adapter s speed or duplex mode has not been configured manually We recommend setting the adapter to auto negotiation
9. F to 104 F Operating 10 to 95 non condensing 143 APPENDIX B Hardware Specifications Wireless Characteristics WIRELESS CHARACTERISTICS FREQUENCY BAND RADIO DATA RATE CHANNELS MODULATION SECURITY 2 4 2 484 GHz 11b 11 5 5 2 1M Automatic 11g 54 48 36 24 18 12 9 6M Automatic 11n HT40 up to 150 Mbps HT20 up to 65 Mbps Automatic Up to 14 depending on region 802 11b 64 QAM 16 QAM QPSK BPSK DSSS 802 119 CCK DQPSK DBPSK 802 11n HT20 and HT40 64 QAM 16 QAM QPSK BPSK WEP WPA WPA2 WPA2 PSK WPA PSK SOFTWARE FEATURES ATM FEATURES PPP FUNCTIONS Support up to 8 ATM PVCs Support ATM Forum UNI 3 1 4 0 PVC Support UBR CBR and rt VBR and nrt VBR service classes Provide ATM layer functionality Support up to 8 PVCs traffic shaping CBR UBR rt nrt VBR Support PPPoA RFC2364 Support MPoA functionality RFC2684 Support IP over ATM IPoA Support ATM cell format ITU T I 361 Support OAM F4 F5 loopback Point to Point Protocol RFC1661 PPP over ATM RFC2364 PPP over Ethernet RFC2516 User Authentication CHAP RFC1994 PAP RFC1334 144 BRIDGE FEATURES ROUTING FEATURES SECURITY FIREWALL MANAGEMENT Qos APPENDIX B Hardware Specifications Software Features Ethernet bridging Support for transparent bridging MAC address learning MAC address filtering and protocol filtering for up link RIP v1 v2 Static routing PPP PPPoE RF
10. Preste atenci n a la carga de potencia de la toma de corriente o de los alargadores Una toma de corriente sobrecargada o l neas y enchufes dafiados pueden provocar descargas el ctricas o un incendio Compruebe los cables de alimentaci n con cierta frecuencia Si detecta alg n dafio reempl celos inmediatamente Deje un espacio adecuado para que se disipe el calor y evitar as cualquier dafio en el dispositivo causado por sobrecalentamiento Los orificios de ventilaci n del dispositivo est n dise ados para disipar el calor y garantizar que dicho dispositivo funciona con normalidad No tape estos orificios de ventilaci n No coloque este dispositivo cerca de un lugar donde haya una fuente de calor o temperaturas elevadas Evite exponer el dispositivo a la luz solar directa No coloque este dispositivo junto a un lugar h medo o mojado No derrame ningun fluido sobre el dispositivo Por favor siga cuidadosamente las instrucciones que figuran en el manual guia de instalaci n r pida para conectar el dispositivo a su PC o a cualquier otro producto electr nico Cualquier conexi n no v lida podr a causar riesgo de descarga o de incendio No coloque este dispositivo en una superficie o soporte inestable 12 COMPLIANCES PRECAU ES DE SEGURAN A Leia atentamente as seguintes informa es antes de utilizar o dispositivo Respeite as seguintes indica es de seguran a para proteger o dispositivo contra riscos e danos
11. CHAPTER 6 LAN Settings LAN Interface LAN INTERFACE By default the ADSL Router is configured with the IP address 192 168 2 1 subnet mask 255 255 255 0 and a default gateway of 192 168 2 1 Figure 34 LAN Configuration LAN Interface Setup This page is used to configure the LAN interface of your ADSL Router Here you may change the setting for IP addresss subnet mask etc Interface Name el IP Address 192 168 2 1 Subnet Mask 255 255 255 0 Secondary IP IGMP Snooping Disable Enable Apply Changes LAN Port Link Speed Duplex Mode Modify Ethernet Status Table Select Port o Link Mode LAN1 Auto Negotiation LAN2 Auto Negotiation LAN3 Auto Negotiation LAN4 Auto Negotiation ae r LER BE NE MAC Address Control LAN1 LAN2 LAN3 LAN4 WLAN Apply Changes New MAC Address Current Allowed MAC Address Table MAC Addr Action The following items are displayed on this page Interface Name Displays the name assigned to the interface IP Address Specifies an IP address for management of the ADSL Router Valid IP addresses consist of four decimal numbers O to 255 separated by periods Default 192 168 2 1 Subnet Mask Indicates the local subnet mask Default 255 255 255 0 Secondary IP Address Specifies a secondary IP address for management of the unit IGMP Snooping Enables Internet G
12. Client ALG parts FTP ALG por 0O Add Dest Forts Delete Selected DestFort FIP ALG ports Table Select NENNEN NNNM e 21 The following items are displayed on this page FTP ALG Port Specifies a non standard FTP port for passthrough traffic Range 0 65535 Add Dest Ports Adds the specified port to the FTP ALG Ports Table Delete Selected Dest Port Removes the selected port from the FTP ALG Ports Table NAT IP MAPPING IP Mapping enables a pool of local LAN IP addresses to be dynamically mapped to a pool of external global IP addresses Figure 56 NAT IP Mapping NAT IP MAPPING Entries in this table allow you to config one IP pool for specified source ip address from lan so one packet which s source ip is in range of the specified address will select one IP address from pool for NAT Type One to One v Local Start IP Local End IP Global Start IP Global End IP Current NAT IP MAPPING Table Local Start IP Local End IP Global Start IP GlobalEndIP Action Delete Selected Delete All 102 CHAPTER 8 Services Quality of Service The following items are displayed on this page Type Selects the type of mapping to use Either one to one one to many many to many or many to one Local Start End IP Defines a local IP address pool range Global Start End IP Defines an external IP address pool range QUALITY
13. Current ATM VC Table IP User Selecint Mode vPlcilencap NAPT IMP DRute Gateway NetMas ym Unnumber Status a The following items are displayed on this page Default Route Selection Enables the default route to be specified or selected automatically VPI Virtual Path Identifier A grouping of virtual channels which connect the same end points and which share a traffic allocation VCI Virtual Channel Identifier A specific virtual channel connecting two end points Encapsulation LLC Logical Link Control This encapsulation method allows multiplexing of multiple protocols over a single ATM virtual connection In some cases the LLC header is followed by a SNAP header which uniquely identifies a routed or bridged protocol This is the default packet encapsulation format used for carrying IP datagrams over AAL5 ATM 82 CHAPTER 7 WAN Settings Channel Configuration VC MUX Virtual Circuit Multiplexing When using this mode the communicating hosts agree on the high level protocol for a given circuit which tends to reduce fragmentation overhead This allows a sender to pass each datagram directly to AAL5 for transfer and requires nothing to be sent besides the datagram and the AAL5 trailer The chief disadvantage of this scheme is that a host must create a separate virtual circuit for each high level protocol if more than one protocol is used Because most carriers charge for each virtual circui
14. Destination The network IP address of the subnet The destination can be specified as the IP address of a subnet or a specific host in the subnet It can also be specified as all zeros to indicate that this route should be used for all destinations for which no other route is defined 118 CHAPTER 9 Advanced Routing Configuration Subnet Mask The network mask of the destination subnet The default gateway uses a mask of 0 0 0 0 Next Hop The IP address of the next hop through which traffic will flow towards the destination subnet Metric Defines the number of hops between network nodes that data packets travel The default value is 0 which means that the subnet is directly one hop away on the local LAN network Interface The WAN interface to which a static routing subnet is to be applied Add Route Adds a static route to the Static Route Table Update Clears the above fields Delete Selected Deletes the specified static route STATIC ROUTE TABLE This table displays all the configured static routes Select Highlights an entry in the Static Route Table State Displays if the route is enabled or disabled Destination Displays the final destination of the routed packets Subnet Mask Displays the subnet mask Next Hop The next hop that the packets will be routed to on their way to their final destination Metric Displays the number of ho
15. Do not power off the device during uploading Otherwise it may crash the system Select File Browse The following items are displayed on this page Select File Specifies the firmware file for the upgrade The file location must be on the local management PC You can use the Browse button to find the file Browse Opens a directory on the local hard drive for specifying the path of file required for uploading Upload Starts the upload procedure Reset Clears all file directory fields 136 CHAPTER 11 Administration Settings TR 069 Configuration TR 069 CONFIGURATION The Technical Report 069 TRO69 protocol defines a specification for remote management of CPE devices The protocol uses HTTP for two way communication between the CPE device and an Auto Configuration Server ACS allowing service providers to provide CPE configuration software upgrades and other service functions for end users The ADSL Router s TR 069 parameters need to be defined to allow communication with the remote ACS Figure 86 TR 069 Configuration TR 069 Configuration This page is used to configure the TR O69 customer premises equipment CPE In this page you can configure the parameters of auto configuration server ACS ACS Enable URL http 20 20 20 20 3090 web tr069 User Name hgw Password eee Periodic Inform Enable Disable 9 Enable Periodic Inform
16. IP Address The IP address of the server on the local Ethernet network The specified address must be in the same subnet as the router and its DHCP server address pool Range 192 168 2 2 to 192 168 2 254 98 CHAPTER 8 Services NAT NAPT Settings NAT EXCLUDE IP You can use the Exclude IP feature to block an IP address or range of IP addresses from accessing WAN interfaces Figure 51 NAT Exclude IP NAT EXCLUDE IP In the page you can config some source IP address which use the purge route mode when access internet through the specified interface interface Current NAT Exclude IP Table WAN Interface ENT TEM Highip Action The following items are displayed on this page Interface Select the WAN interface for the Exclude IP service IP Range Specifies an IP address range to block on the WAN interface NAT FORWARDING Forwarding allows an external user to reach a private IP address inside a LAN from the outside through a NAT enabled router Figure 52 NAT Forwarding Settings NAT Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to hast some sort of server like a web server or mail server on the private local network behind your Gateway s NAT firewall Local IP Address Remote IP Address Enable Current NAT Port Forwarding Table Local
17. Interval 300 Connection Request User Name itms Password FIIIT Path 053 Port FAS Debug ACS Certificates CPE 9 No O Yes Show Message Disable O Enable CPE Sends GetRP C Disable O Enable Skip MReboot Disable C Enable Delay Disable Enable Auto Execution Disable 9 Enable Certificate Management CPE Certificate client Password CPE Certificate Browse CA Certificate Browse 137 CHAPTER 11 Administration Settings TR 069 Configuration The following items are displayed on this pages ACS Defines the Auto Configuration Server parameters Enable Enables disables TR 069 support Default Enabled URL Speceifies the URL required for the CPE to connect to the ACS User Name Enter the user name that the ADSL Router should use when connecting to the ACS Password Enter the password that the ADSL Router should use when connecting to the ACS Periodic Inform Enable When this field is enabled the DSL device will send an Inform RPC to the ACS server at the system startup and will continue to send it periodically at an interval defined in Periodic Inform Interval field When this field is disabled the DSL device will only send Inform RPC to the ACS server once at the system startup Default Enabled Periodic Inform Interval Time interval in seconds to send Inform RPC CONNECTION REQUES
18. Low Default Low Select All Selects all DoS prevention measures listed Clear All Clears all fields Enable Source IP Blocking When multiple attacks are detected from each of the fields listed above or the packet threshold has been exceeded the IP address of the hacker is blocked Block Time sec Sets the length of time in seconds the IP address Should remain blocked IGMP PROXY CONFIGURATION Multicasting is useful when the same data needs to be sent to more than one host Using multicasting as opposed to sending the same data to the individual hosts uses less network bandwidth The multicast feature also enables you to receive multicast video stream from multicast servers IP hosts use Internet Group Management Protocol IGMP to report their multicast group memberships to neighboring routers Similarly multicast routers use IGMP to discover which of their hosts belong to multicast groups This device supports IGMP proxy that handles IGMP messages When enabled this device acts as a proxy for a LAN host making requests to join and leave multicast groups or a multicast router sending multicast packets to multicast group on the WAN side When you enable IGMP Proxy make sure IGMP is also enabled on the WAN interface upstream that connects to a router running IGMP You must also enable IGMP on the LAN interface downstream that is connected to hosts Ili CHAPTER 8 Services IGMP Proxy Co
19. OF SERVICE The Quality of Service page is used to enable or disable QoS and set the default priority for packets not matching any classification rules Click Services IP QoS If QoS is enabled the default priority should also be set to an appropriate value After setting any of the attributes on this page click Apply Figure 57 Quality of Service IP QoS Entries in the table are used to assign the precedence for each incoming packet according to the specified policy The procedure for configuring quality of service Q05 is as follows 1 Enable Qos 2 Set traffic rule 3 Assign the precedence or add marker for different stream IP QoS Disable 9 Enable QoS Policy 802 1p based Schedule Mode Strict prior 802 1p configuration QoS Rule List Stream Rule Behavior 4 Dest IP IP psec pon Dest Por Php races wr Add QoS Rule Source IP Source Mask 255 255 255 255 Destination IP Destination Mask Source Port Destination Port Protocol Physical Port Set Priority pa Lowest v Insert or Modify QoS Mark IP Precedence IP ToS 802 1p 105 CHAPTER 8 Services Quality of Service The following items are displayed on this page IP QoS If enabled QoS rules will be applied to traffic entering the Gateway QoS Policy Selects Stream based
20. Ping echo requests to other devices 127 Traceroute Checks routes to other devices 128 ADSL Runs ADSL diagnostic tone tests 130 Admin Commit Reboot Reboots the unit and or restores factory defaults 133 Backup Restore Backs up or restores configuration settings 134 Password Setup Changes the web access passwords 135 Upgrade Firmware Upgrades the unit s software version 136 Configure TR 069 Configures parameters for establishing a connection 137 between the router and an auto configuration server 39 CHAPTER 3 System Configuration Setup Wizard SETUP WIZARD The Wizard is designed to help you configure the basic settings required to get the ADSL Gateway Router up and running Click Wizard in the main menu to get started STEP 1 GETTING After reading the wizard welcome message click Next to continue STARTED Figure 7 Wizard Step 1 Getting Started 1 Getting Started Welcome Thank you for purchasing the SMC Barricade After answering the following questions you will be online and free to enjoy high speed Internet Access Before you begin please make sure the SMC Barricade is connected correctly For a detailed description please refer to the user manual This can be found on the documentation CD provided If everything is OK click the NEXT button to continue STEP 2 TIME ZONE Configure a Network Time Protocol NTP server to poll for time updates To synchronize the router with an NTP server sp
21. The following conventions are used throughout this guide to show information NoTE Emphasizes important information or calls your attention to related features or instructions CAUTION Alerts you to a potential hazard that could cause loss of data or damage the system or equipment WARNING Alerts you to a potential hazard that could cause personal injury This section summarizes the changes in each revision of this guide MARCH 2012 REVISION This is the first revision of this guide m Eu CONTENTS WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 15 CONTENTS 16 FIGURES 21 TABLES 24 SECTION GETTING STARTED 25 1 INTRODUCTION 26 Features and Benefits 26 Description of Hardware 27 Power Connector 29 Power Button 29 WLAN Button 29 WPS Button 29 Reset Button 29 2 INSTALLING THE ROUTER 30 Package Contents 30 System Requirements 30 Cable Connections 31 Powering On 32 Configuring the TCP IP Protocols 32 SECTION Il WEB CONFIGURATION 35 3 SYSTEM CONFIGURATION 36 Using the Web Interface 36 m d CONTENTS Home Page 37 Setup Wizard 40 Step 1 Getting Started 40 Step 2 Time Zone 40 Step 3 ADSL Settings 41 Step 4 Wireless Settings 43 Step 4 Configuration Saving 44 4 DEVICE INFORMATION 45 System Status 45 LAN Status 46 WLAN Status 47 WAN Status 48 Port Mapping 49 Traffic Statistics 50 DSL Statistics 51 ARP Table 52 5 WLAN CONFIGURATION 54 WLAN Basic Settings 55 Advanced
22. This page is used to configure DHCP mode You can set DHCP mode to None DHCP Relay or DHCP Server 1 Set the DHCP mode to DHCP Server if you are using this device as a DHCP server This page lists an IP address pool available to hosts on your LAN The device assigns IP addresses in the pool to hosts on your network when they request Internet access 2 Set the DHCP mode to DHCP Relay if you are using another DHCP server to assign IP address to your hosts on the LAN You can set the IP address of the DHCP server 3 If you set the DHCP mode to None the device does not assign IP addresses to the hosts when they request an IP address LAN IP Address 192 168 2 1 Subnet Mask 255 255 255 0 DHCP Mode DHCP Server VJILANI MLAN IvLAN3 MLAN4 4WLAN MVAPO IVAP1 MIVAP2 MVAP3 IP Pool Range 192 168 2 2 192 168 2 254 Show Client Default Gateway 192 168 2 1 Interface Max Lease Time 1440 minutes Domain Name domain com DNS Servers 8 8 8 8 F oes WDS CHAPTER 5 WLAN Configuration WDS 71 LAN SETTINGS This chapter describes LAN configuration on the ADSL Router You can use the web browser interface to access IP addressing only if the ADSL Router already has an IP address that is reachable through your network LAN Interface on page 73 IPv6 LAN Configuration on page 74 DHCP Settings on page 76 72
23. a Demilitarized Zone DMZ host the PC s TCP ports are completely exposed to the Internet allowing open two way communication The host PC should be assigned a static IP address Figure 59 DMZ Settings DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers Enable DMZ DMZ Host IP Address The following items are displayed on this page Enable DMZ Sets the DMZ status to enabled but changes do not take affect until the Apply changes button has been pressed and changes are saved to the running configuration Default disabled DMZ Host IP Address Specifies an IP address on the local network allowed unblocked access to the WAN 106 CHAPTER 8 Services URL Blocking URL BLOCKING By filtering inbound Uniform Resource Locators URLs the risk of compromising the network can be reduced URLs are commonly used to point to websites By specifying a URL or a keyword contained in a URL traffic from that site may be blocked Figure 60 URL Blocking Settings URL Blocking Configuration This page is used to configure the filtered keyword Here you can add delete filtered keyword URL Blocking Capability C Disable Enable Apply Changes Keywords Addkeyword Delete
24. activated The ADSL Gateway Router must be powered with its supplied power adapter Failure to do so results in voiding of any warrantly supplied with the product The power adapter automatically adjusts to any voltage between 100 240 volts at 50 or 60 Hz and supplies 12 volts DC power to the unit No voltage range settings are required The ADSL Gateway Router has a power button When the AC power adapter is attached and connected to a power source the power button must be depressed to power on the unit Turns the ADSL Gateway Router s Wi Fi radio on or off The WLAN LED on the front panel indicates when the Wi Fi radio is enabled Push this button to start WPS authentication of a wireless device After a device is successfully added to the network by WPS the WPS LED will remain on for about 5 minutes and then turn off This button is used to restore the factory default configuration If you press and hold down the button for 8 seconds or more any configuration changes you may have made are removed and the factory default configuration is restored to the unit 29 INSTALLING THE ROUTER Before installing the ADSL Gateway Router verify that you have all the items listed in Package Contents If any items are missing or damaged contact your local distributor Also be sure you have all the necessary tools and cabling before installing the router PACKAGE CONTENTS After unpacking the ADSL Gateway Router check the
25. and so on Enable SNMP System Description ADSL Router Modem IGD System Contact System Name SMC7901 BRAS System Location Trap IP Address Community Name Read only public Community Name Read Write public The following items are displayed on this pages SNMP Enables disables SNMP Default Enabled System Description A name given to identify the ADSL Router System Contact The name of the system contact person System Name A description of the unit Default Wireless ADSL Modem Router System Location The location of the ADSL Router Trap IP Address Destination IP address of the SNMP trap Community Name Read only Name of the read only community This read only community allows read operation to all objects in the Management Information Base MIB Community Name Read Write Name of the write only community This write only community allows write operations to objects defined as read writable in the MIB X21 CHAPTER 9 Advanced System Time Configuration SYSTEM TIME CONFIGURATION The System Time page allows you to manually configure time settings or enable the use of an NTP server Figure 71 System Time Configuration System Time Configuration This page is used to configure the system time and Network Time Protocol NTP server In this page you can modify the settings or view some information of the system time and NTP pa
26. causados por fogo e energia el ctrica Utilize o transformador inclu do na embalagem do dispositivo Respeite a pot ncia da tomada el ctrica e das extens es Uma tomada el ctrica sobrecarregada ou cabos e fichas danificadas podem causar choques el ctricos ou fogo Verifique regularmente os cabos de alimenta o Caso algum se encontre danificado substitua o imediatamente necess rio deixar algum espaco livre em volta do dispositivo para dissipa o de calor de forma a evitar danos causados pelo sobreaquecimento do dispositivo Os orif cios de ventila o do dispositivo foram concebidos para dissipar o calor e assegurar que o mesmo funciona normalmente Nao bloqueie esses orificios de ventila o Nao coloque este dispositivo junto a fontes de calor ou em locais com temperaturas elevadas Evite colocar o dispositivo sob luz solar directa Nao coloque este dispositivo junto a locais molhados ou com humidade N o derrame l quidos sobre o dispositivo Por favor siga atentamente as instru es do manual guia de instala o r pida para conectar o dispositivo ao seu PC ou a qualquer outro dispositivo electr nico Aten o que qualquer tipo de liga o inv lida pode originar risco de choque el ctrico ou de inc ndio N o coloque este dispositivo numa superf cie ou suporte inst veis 13 COMPLIANCES ENVIRONMENTAL STATEMENT The manufacturer of this product endeavours to sustain an environment
27. contents of the box to be sure that you have received the following components Barricade ADSL Gateway Router SMC7904WBRAS N2 v2 RJ 45 Category 5 network cable RJ 11 telephone cable ADSL splitter AC power adapter Quick Installation Guide Documentation CD 9 SMC warranty information card Please inform your dealer if there are any incorrect missing or damaged parts If possible retain the carton including the original packing materials in case there is a need to return the unit for repair SYSTEM REQUIREMENTS Before you start installing the router make sure you can provide the right operating environment See the following installation requirements A PC or Macintosh with a 10 100 Mbps Ethernet adapter card installed Or a Windows PC with an available USB port For Internet access the computer must be configured for TCP IP 30 CHAPTER 2 Installing the Router Cable Connections Power requirements 12 VDC using the included AC power adapter Make sure that a properly grounded power outlet is within 1 8m 6ft of the router The router should be located in a cool dry place with at least 5 cm 2 in of space on all sides for ventilation Place the router out of direct sunlight and away from heat sources or areas with a high amount of electromagnetic interference The temperature and humidity should be within the ranges listed in the specifications CABLE CONNECTIONS
28. default setting Hexadecimal Enter keys as 10 hexadecimal digits 0 9 and A F for 64 bit keys or 26 hexadecimal digits for 128 bit keys Default Tx Key Selects the default key used for transmission Encryption Key 1 4 Specifies the user defined WEP keys WPA SECURITY The following section describes WPA WPA2 and WPA2 mixed settings Figure 26 Wireless Security Setup WPA WPA2 Setup Wireless Security Setup This page is used to configure wireless security mode Set the encryption mode to WEP or WPA which prevents any unauthorized access to your wireless network SSID Type Root OVAPO OCVAP1 OVAP2 OVAP3 Encryption WPA TKIP 4 Use 802 1x Authentication WEP 64bits WEP 128bits WPA Authentication Mode 8 Enterprise RADIUS Personal Pre Shared Key Pre Shared Key Format Pre Shared Key Authentication RADIUS Port 1812 IP address 0 0 0 0 Password Server Note When encryption WEP is selected you must set WEP key value Apply Changes The following items are displayed on this page 62 CHAPTER 5 WLAN Configuration Wireless Security Setup WPA Authentication Mode Selects between modes of WPA authentication Options are Enterprise Uses a RADIUS server for authentication This applies to enterprise deployment Personal Uses a pre shared key for authentication ENTERPRISE RADIUS Port Specifies the port number used to communicate with the R
29. frames Range 256 2346 bytes Default 2346 bytes RTS Threshold Sets the packet size threshold at which a Request to Send RTS signal must be sent to a receiving station prior to the sending station starting communications The wireless interface sends RTS frames to a receiving station to negotiate the sending of a data frame After receiving an RTS frame the station sends a CTS clear to send frame to notify the sending station that it can start sending data Beacon Interval The rate at which beacon signals are transmitted from the wireless interface The beacon signals allow wireless clients to 57 CHAPTER 5 WLAN Configuration Advanced Settings maintain contact with the ADSL Router They may also carry power management information Range 20 1000 TUs Default 100 TUs DTIM Interval The rate at which stations in sleep mode must wake up to receive broadcast multicast transmissions Known also as the Delivery Traffic Indication Map DTIM interval it indicates how often the MAC layer forwards broadcast multicast traffic which is necessary to wake up stations that are using Power Save mode The default value of one beacon indicates that the access point will save all broadcast multicast frames for the Basic Service Set BSS and forward them after every beacon Using smaller DTIM intervals delivers broadcast multicast frames in a more timely manner causing stations in Power Save mode to wake up more often
30. is rebooting now Please wait for 57 Is 39 CHAPTER 11 Administration Settings Backup Restore Settings BACKUP RESTORE SETTINGS The Backup Restore Settings page allows you to backup current settings to a local file and load previously saved settings to the unit Figure 83 Backup Restore Settings Backup Restore Settings Once the router is configured you can save the configuration settings to a configuration file on your hard drive You also have the option to load configuration settings Save Settings to File Load Settings from File Browse Upload The following items are displayed on this page Save Settings to File Saves the current configuration to a file locally on the management PC Load Settings from File Allows the user to load previously saved configuration files from a local file on the management PC 134 PASSWORD SETUP CHAPTER 11 Administration Settings Password Setup Management access to the ADSL Router is controlled through different levels of user name and password To protect access to the management interface you need to configure a new Administrator s password as soon as possible If a new password is not configured then anyone having access to the ADSL Router may be able to compromise the unit s security by entering the default values Figure 84 Password Setup User Account Configuration This page is used to add user account to access the web
31. of Virtual Servers Port Triggering and other features Some applications such as Internet gaming videoconferencing Internet telephony and others require multiple connections These applications may not work with Network Address Translation NAT enabled If you need to run applications that require multiple connections use Port Triggering to specify the additional public ports to be opened for each application Alternatively you can open up a client to unrestricted two way Internet access by defining it as DMZ demilitarized zone host Using the NAT Virtual Server feature remote users can access different servers on your local network using your single public IP address Remote users accessing services such as web or FTP at your local site thorugh your public IP address are redirected mapped to other local server IP addresses and TCP UDP port numbers For example if you set Type Public Port to TCP 80 HTTP or web and the Private IP Port to 192 168 7 9 80 then all HTTP requests from outside users forwarded to 192 168 7 9 on port 80 Therefore by just using your external IP address provided by your ISP Internet users can access the services they need at the local addresses to which you redirect them The more common TCP service port numbers include HTTP 80 FTP 21 Telnet 23 and POP3 110 Up to 32 entries can be configured in the Virtual Servers table 97 CHAPTER 8 Services NAT NAPT Settings Figure 50 NAT
32. page LAN IP Address Displays the LAN IP address for management of the ADSL Router Default 192 168 2 1 Subnet Mask Displays the local subnet mask Default 255 255 255 0 DHCP Mode When set to DHCP Server enables the ADSL Router to act as a DHCP server Interface Selects either the RJ 45 LAN ports or wireless interfaces IP Pool Range Configures the IP address pool for the DHCP server and determines how many IP addresses can be assigned NoTE Do not enter the ADSL Router s LAN IP address as part of the IP Pool range Show Client Displays the current DHCP client table Default Gateway Specifies the gateway address through which traffic is routed from Usually the LAN IP address of the ADSL Router 78 CHAPTER 6 LAN Settings DHCP Settings MAX Lease Time Select a time limit for the use of an IP address from the IP pool When the time limit expires the client has to request a new IP address The lease time is expressed in seconds Default 86400 seconds Range 60 86400 seconds 1 indicates an infinite lease time Domain Name Specifies the unique name used to identify the ADSL Router on the network DNS Servers Sets up to three domain name server IP addresses Set VendorClass IP Range Click on this option to assign IP address ranges to specific device types Device Name Describes the device type Start End Address S
33. processor DSP DSP Version The current hardware version of the digital signal processor DSP CRC Errors Displays the CRC cyclic redunancy check a type of function that takes as input a data stream of any length and produces as output a value of a certain space commonly a 32 bit integer Upstream Downstream BER The the rate at which bits in the data stream that have been altered by noise Up Down Output Power Displays the upstream downstream power level employed for ADSL port filtering ES Displays the total error seconds the number of second intervals during which there was one or more CRC anomalies or one or more Loss of Signal LOS or Loss of Framing LOF defects SES Displays the total severly errored seconds The number of second intervals containing 18 or more CRC 8 anomalies one or more Loss of Signal LOS defects one or more Severely Errored Frame SEF defects or one or more Loss of Power LPR defects UAS Displays the total unavailable errored seconds the number of seconds during which the ADSL transceiver is powered up but not available ADSL Retrain Retrains the DSL line ARP TABLE The ARP page displays IP address to MAC address mapping entries determined by the Address Resolution Protocol Figure 19 Status ARP Table ARP Table This page shows current ARP entries by interrogating the current protocol data IP Address MAC Address 192 168 2 9 0
34. sideband The extension channel allows you to get extra bandwidth Channel Number The radio channel that the ADSL Router uses to communicate with wireless clients When multiple access points are deployed in the same area set the channel on neighboring access points at least five channels apart to avoid interference with each other For example you can deploy up to three access points in the same area using channels 1 6 11 Note that wireless clients automatically set the channel to the same as that used by the ADSL Router to which it is linked Default Auto Range 1 11 Radio Power percent Adjusts the power of the radio signals transmitted from the access point The higher the transmission power the farther the transmission range Power selection is not just a trade off between coverage area and maximum supported clients You also have to ensure that high power signals do not interfere with the operation of other radio devices in the service area Default 100 Range 100 80 50 25 10 Associated Clients Opens a window that displays information on current connected wireless clients 56 CHAPTER 5 WLAN Configuration Advanced Settings ADVANCED SETTINGS The advanced radio configuration settings are described in the page that follows Figure 21 Wireless Security Setup Advanced Settings Wireless Advance Settings These settings are only for more technically advanced users who have a suffic
35. the WPS process This page configures up to four VAPs virtual access points on the ADSL Router Each VAP functions as a separate access point and can be configured with its own Service Set Identification SSID and security settings However most radio signal parameters apply to both VAP interfaces The VAPs function similar to a VLAN with each VAP mapped to its own VLAN ID Traffic to specific VAPs can be segregated based on user groups or application traffic Each VAP can have its own wireless clients whereby the clients associate with these VAPs the same as they would with a physical access point 66 CHAPTER 5 WLAN Configuration MBSSID Figure 29 Second BSSID Wireless Multiple BSSID Setup This page allows you to set virutal access points VAP Here you can enable disable virtual AP and set its SSID and authentication type click Apply Changes to take it effect Enable VAPO SSID Broadcast SSID Relay Blocking Authentication Type Enable VAP1 SSID Broadcast SSID Relay Blocking Authentication Type Enable VAP SSID Broadcast SSID Relay Blocking Key Enable Disable Enable Disable Open System Auto Shared Key Enable Disable Enable Disable Open System Auto Shared Enable Disable Enable Disable Open System Shared Authentication Type Key rie Enable VAP3 SSID Broadcast SSID Relay Blocking Disable
36. twisted pair cable Virtual Private Network A secure tunnel used to protect data passing from one network to another over the Internet Wide Area Network A computer network that spans a relatively large geographical area Typically a WAN consists of two or more local area networks LANs 199 NUMERICS 10 100BASE TX pin assignments 148 100BASE TX 27 10BASE T 27 A access control 63 ACLs 92 ADSL capability 87 ADSL modulation 86 ADSL settings 86 ADSL tone diagnostics 130 advanced settings 57 AnnexL option 87 AnnexM option 87 ARP table 52 ATM settings 84 B backup restore settings 134 bridge configuration 116 buttons Reset 29 C cable connections 31 channel configuration 82 commit reboot 133 compliances emissions 146 environmental 146 crossover cables 149 current ATM VC table 85 D DDNS 90 default settings reset 29 denial of service DoS 109 DHCP settings 76 DHCP relay 77 DHCP server 78 no DHCP 76 DMZ 106 DNS server 89 DSL statistics 51 INDEX E Ethernet 2 7 F factory defaults resetting 29 front panel 27 28 G Gateway features 26 guard interval 58 H hardware description 27 HT channel bandwidth 55 IGMP proxy configuration 111 installation connecting cables 31 powering on 32 IP Port filtering 95 L LAN interface 73 74 LAN status 46 LAN WAN diagnostics test 126 LED indicators 28 M MAC filtering 105 P package contents 30 password setup 1
37. when installing the network driver PROBLEMS ACCESSING THE MANAGEMENT INTERFACE Table 4 Web Access Troubleshooting Chart Symptom Cannot connect using a e web browser e Forgot or lost the password Action Be sure the router is powered up Check the network cabling between the management station and the router Check that you have a valid network connection to the router and that the port you are using has not been disabled Be sure the management station has an IP address in the same subnet as the router s IP interface to which it is connected Press and hold down the Reset button for 3 seconds or more to restore the unit s factory default settings then use the default password to access the web interface 1427 HARDWARE SPECIFICATIONS PHYSICAL CHARACTERISTICS PORTS ETHERNET INTERFACE DSL INTERFACE LED INDICATORS INPUT POWER SIZE WEIGHT TEMPERATURE HUMIDITY 1 RJ 11 DSL line to phone jack in the wall 4 RJ 45 10 100BASE TX Ethernet connection to PC RJ 45 connector auto MDI X pinout detection 10BASE T 100 ohm UTP cable Category 3 or better 100BASE TX 100 ohm UTP cable Category 5 or better Maximum Cable Length 100 m 328 ft RJ 11 connector using standard phone cable 26 AWG Power DSL Internet LAN WLAN WPS 12 VDC via AC power adapter 800 mA maximum 140 x 104 x 28 5 mm 5 51 x 4 09 x 1 12 in 177 g 6 2 oz Operating 0 C to 40 C 32
38. wireless networks TKIP or AES is used as the multicast encryption cipher WPA2 TKIP AES WPA2 WPA was introduced as an interim solution for the vulnerability of WEP pending the ratification of the IEEE 802 11i wireless security standard In effect the WPA security features are a subset of the 802 11i standard WPA2 includes the now ratified 802 11i standard but also offers backward compatibility with WPA Therefore WPA2 includes the same 802 1X 59 CHAPTER 5 WLAN Configuration Wireless Security Setup and PSK modes of operation TKIP or AES is used as the multicast encryption cipher WPA2 Mixed Clients using WPA or WPA2 are accepted for authentication TKIP or AES is used as the multicast encryption cipher The following figures illustrate the various options available with each security setting Figure 23 Wireless Security Setup None Wireless Security Setup This page is used to configure wireless security mode Set the encryption mode to WEP or VVPA which prevents any unauthorized access to your wireless network SSID Type Root OVAPO OVAPTI OVAP2 OVAP3 Encryption None Use 802 1x Authentication WEP 64bits WEP 128bits WPA Authentication Mode Enterprise RADIUS Personal Pre Shared Key Pre Shared Key Format Pre Shared Key Authentication RADIUS Port 1812 IP address 0 0 Password Server Note When encryption WEP is selected you must set WEP key va
39. 0 30 F1 2F BE 30 192 168 2 1 00 1F A4 90 7F 3E 52 CHAPTER 4 Device Information ARP Table The following items are displayed on this page IP Address IP address of a local entry in the cache MAC Address MAC address mapped to the corresponding IP address Refresh Sends a request to update the current parameters 53 WLAN CONFIGURATION This chapter describes wireless configuration on the ADSL Router The unit contains an onboard IEEE 802 11b g n access point AP which provides wireless data communications between the router and wireless devices WLAN Configuration contains the following sections WLAN Basic Settings on page 55 Advanced Settings on page 57 Wireless Security Setup on page 59 Wi Fi Protected Setup WPS on page 65 Access Control on page 64 MBSSID on page 66 WDS on page 68 DA s CHAPTER 5 WLAN Configuration WLAN Basic Settings WLAN Basic SETTINGS The unit s access point can function in one of three modes mixed 802 11b g 802 11b only or 802 11g only Also note that 802 11g is backward compatible with 802 11b at slower data rates Note that the unit supports two virtual access point VAP interfaces Figure 20 WLAN Basic Settings Wireless Basic Settings This page is used to configure the parameters for your wireless network Disable Wireless LAN Interface Band 24 GHz B G N
40. 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable Table 5 10 100BASE TX MDI and MDI X Port Pinouts PIN MDI Signal Name MDI X Signal Name 1 Transmit Data plus TD Receive Data plus RD 2 Transmit Data minus TD Receive Data minus RD 3 Receive Data plus RD Transmit Data plus TD 6 Receive Data minus RD Transmit Data minus TD 4 5 7 8 Not used Not used a The and signs represent the polarity of the wires that make up each wire pair STRAIGHT THROUGH WIRING If the twisted pair cable is to join two ports and only one of the ports has an internal crossover MDI X the two pairs of wires must be straight through When auto negotiation is enabled for any RJ 45 port on this gateway you can use either straight through or crossover cable to connect to any device type Figure 88 Straight through Wiring EIA TIA 568B RJ 45 Wiring Standard 10 100BASE TX Straight through Cable White Orange Stripe Orange White Green Stripe EndA Blue End B White Blue Stripe Green LIN WI CONOOaRWN White Brown Stripe Brown 148 APPENDIX C Cables and Pinouts Crossover Wiring CROSSOVER WIRING If the twisted pair cable is to join two ports and either both ports are labeled with an X MDI X or neither port is labeled with an X MDI a crossover must be imple
41. 35 PBC mode WPS 65 pin assignments RJ 11 150 PIN code WPS 65 ping 127 pinouts cable 147 154 port RJ 11 27 RJ 45 27 port indicators 28 power adapter details 29 power connector 29 powering on 32 problems troubleshooting 141 H rear panel 27 28 Reset button 29 RIP configuration 113 RJ 11 pin assignments 150 port 27 RJ 45 connector pins 147 RJ 45 port 27 routing configuration 118 o second BSSID 66 SNMP protocol configuration 121 specifications component 143 144 environmental 143 power 143 specifications hardware 143 standards IEEE 146 ITU T 146 straight through cables 148 system indicators 28 requirements 30 system log 11 7 T TCP IP PC configuration 32 time zone 122 TR 069 configuration 137 traffic statistics 50 troubleshooting 141 Internet connection 142 management access 142 twisted pair cable assignments 147 U upgrade firmware 136 UPnP 120 URL blocking 107 UTP cable pinouts 148 INDEX W WAN status 47 48 Web interface access requirements 36 home page 37 wireless security setup 59 common wireless parameters 59 WEP security 60 WLAN basic settings 55 WPA security 62 WPS security 65 es Lo ESHGESoGe SMC NETWORKS Headquarters amp Sub Sahara Africa Office No 1 Creation Rd Ill Hsinchu Science Park Taiwan 30077 Tel 886 3 5770270 Fax 886 3 5780764 Asia Pacific Office 1 Coleman Street 07 09 The Adelphi Singapore 17
42. 46 CABLES AND PINOUTS TWISTED PAIR CABLE ASSIGNMENTS For 10 100BASE TX connections a twisted pair cable must have two pairs of wires For 1000BASE T connections the twisted pair cable must have four pairs of wires Each wire pair is identified by two different colors For example one wire might be green and the other green with white stripes Also an RJ 45 connector must be attached to both ends of the cable NOTE Each wire pair must be attached to the RJ 45 connectors in a specific orientation CAUTION DO NOT plug a phone jack connector into the RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform with FCC standards The following figure illustrates how the pins on the RJ 45 connector are numbered Be sure to hold the connectors in the same orientation when attaching the wires to the pins Figure 87 RJ 45 Connector J47 APPENDIX C Cables and Pinouts 10 100BASE TX Pin Assignments 10 100BASE TX PIN ASSIGNMENTS Use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections 100 ohm Category 3 or better cable for 10 Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet The RJ 45 port on the router supports automatic MDI MDI X operation so you can use straight through or crossover cables for all network connections to PCs switches or hubs In straight through cable pins 1
43. 5 CE SMC Networks declar c acest dispozitiv fara fir respecta cerintele esentiale precum si alte dispozitii relevante ale Directivei 1999 5 EC Manufacturer t mto vyhlasuje Ze Radio LAN device sp a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Manufacturer izjavlja da je ta radio LAN device v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES Por medio de la presente Manufacturer declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE H rmed intygar Manufacturer att denna Radio LAN device st r verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG SMC Networks bu kablosuz cihaz n temel gereksinimleri ve 1999 5 EC yonergesindeki ilgili ko ullar kar lad n beyan eder SAFETY PRECAUTIONS Read the following information carefully before operating the device Please follow the following precaution items to protect the device from risks and damage caused by fire and electric power Use the power adapter that is included with the device package Pay attention to the power load of the outlet or prolonged lines An overburdened power outlet or damaged cords and plugs may cause electric shock or fire Check the power cords regularly if you find any damage replace it at once
44. 68 2 9 icmp seq 1 ttl 10 time 100 ms 2nd 64 bytes from 192 168 2 9 icmp seq ttl 10 time 100 ms 3rd 64 bytes from 192 168 2 9 icmp seq 3 ttl 10 time 100 ms PiNG6 The ADSL Router can also ping IPv6 addresses on specific interfaces to test for connectivity Figure 77 Ping6 Ping6 Diagnostic Target Address Interface La TRACEROUTE CHAPTER 10 Diagnostics Traceroute Traceroute discovers the routes that packets take when traveling to a destination Traceroute works by taking advantage of the error messages generated by routers when a packet exceeds its time to live TTL value The traceroute command first sends probe datagrams with the TTL value set at one This causes the first router to discard the datagram and return an error message The trace function then sends several probe messages at each subsequent TTL level and displays the roundtrip time for each message Not all devices respond correctly to probes by returning an ICMP port unreachable message If the timer goes off before a response is returned the trace function prints a series of asterisks and the Request Timed Out message A long sequence of these messages terminating only when the maximum timeout has been reached may indicate this problem with the target device A trace terminates when the destination responds when the maximum timeout TTL is exceeded or the maximum number of hops is exceeded Figure 78 Traceroute Tracer
45. 802 1p based or DSCP based policy Schedule Mode Selects either Strict or Weighted Fair Queueing WFQ as the port priority mode 802 1p Configuration When the QoS Policy is 802 1p based you can map the 802 1p values to port priority queues DSCP Configuration When the QoS Policy is DSCP based you can map the DSCP values to port priority queues Add QoS Rule Specifies traffic classification rules based on protocol type and destination source MAC address and to set the resulting priority queue re marked IP Precedence IP ToS or 802 1p priority Source IP Mask The source IP address and network mask Destination IP Mask The destination IP address and network mask Source Port The TCP UDP source port Destination Port The TCP UDP destination port m Protocol The network protocol TCP UDP or ICMP Physical Port Select the physical interface LAN or USB Set Priority The port queue to which a matching packet is assigned Insert or Modify QoS Mark Re marks the matching packet with the selected IP Precedence IP ToS or 802 1p value 104 MAC FILTERING CHAPTER 8 Services MAC Filtering MAC based packet filtering enables the router to filter clients based on their physical layer address Figure 58 MAC Filtering Settings MAC Filter Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway U
46. 9803 Tel 65 63387667 Fax 65 63387767 Europe amp N Africa Office C Fructu s Gelabert 6 8 2 2 Edificio Conata II 08970 Sant Joan Desp Barcelona Spain Tel 34 93 477 4920 Middle East Office Office No 416 Le Solarium Bldg Dubai Silicon Oasis Dubai U A E Tel 971 4 3564800 Fax 971 4 3564801 North America Office 20 Mason Irvine CA 92618 U S A Tel 1 949 679 8000 www edge core com www smc com Networks SMC NETWORKS TECHNICAL SUPPORT From Singapore in English and asz Mon Fri 9 AM to 5 PM Tel 65 63387667 Ext 4 From the United Arab Emirates in English Sun Thu 9 AM to 6 PM Tel 971 800 222866 971 4 3564810 From U S A and Canada 24 hours a day 7 days a week Tel 1 800 SMC 4 YOU 1 949 679 8000 Fax 1 949 679 1481 English Technical Support information available at www smc com English for Asia Pacific Technical Support information at www smc asia com English for Middle East Technical Support information at muneer smc asia com Deutsch Technischer Support und weitere Information unter www smc com Espanol En www smc com Ud podr encontrar la informaci n relativa a servicios de soporte t cnico Francais Informations Support Technique sur www smc com Portugu s Informac es sobre Suporte T cnico em www smc com Italiano Le informazioni di supporto tecnico sono disponibili su www smc com Svenska Information om Teknisk Support finns tillgangligt pa www s
47. A countries except in France and Italy where restrictive use applies In Italy the end user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and or for supplying public access to telecommunications and or network services This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed information the end user should contact the national spectrum authority in France C 5 COMPLIANCES This equipment may be operated in The official CE certificate of conformity can be downloaded by selecting the relevant model part number from www smc com gt support gt download Bulgarian C Hactosleto SMC Networks neknapupa ue TOBa 6E32 KNYHO YCTPONCTBO e B CbOTBeTCTBMe CbC CbLUECTBEHUTE N3ZNCKBAHMA N Apyrute npunoxnmn paanopegn u Ha lnpekruBa 1999 5 EC Bbnrapcku Czech Manufacturer timto prohlaSuje ze tento Radio LAN device je ve shod se zakladnimi Cesky po adavky a dal mi p slu n mi ustanoven mi sm rnice 1999 5 ES Danish Undertegnede Manufacturer erkl rer herved at f lgende udstyr Radio LAN device Dansk overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Dutch Hierbij verklaart Manufacturer dat het toestel Radio LAN device in overeenstemming is Neder
48. ADIUS server IP Address Specifies the IP address used to communicate with the RADIUS server Password Specifies the password necessary for access to RADIUS server authentication PERSONAL PRE SHARED KEY Pre Shared Key Format Selects the format of the pre shared key from the following options Passphrase Enter a key as an easy to remember form of letters and numbers The string must be from 8 to 63 characters which can include spaces Hexadecimal Enter a key as a string of 64 hexadecimal numbers Pre Shared Key Enter the pre shared key noting the type chosen 63 ACCESS CONTROL CHAPTER 5 WLAN Configuration Access Control Access control configures ACLs access control lists which allow or deny wireless traffic based on the sender s MAC address Figure 27 Wireless Security Setup Wireless Access Control Wireless Access Control This page is used to configure the wireless access control If you set the wireless access control mode to Allowed Listed only those clients whose wireless MAC addresses are in the access control list are allowed to connect to your access point AP If you set the wireless access control mode to Deny Listed those clients whose wireless MAC addresses are in the access control list are blocked from connecting to your AP Wireless Access Control Mode Allow Listed Apply Changes MAC Address ex D0E086710502 Current Access Co
49. C 2516 NAT with ALGs NAPT IGMP v1 v2 IGMP proxy and snooping IPv4 IP pass through ARP binding Port mapping Stateful Packet Inspection SPI Management Access Control for WAN User authentication for PPP PAP CHAP DDoS Dynamic DoS Protection NAT DMZ Filtering IP Filtering MAC Filtering URL Filtering ACL Access Control List VPN IPSec PPTP L2TP pass through Software Forbidden Access administration Web based configuration HTTP server System configuration backup and restore SNMP Support V 1 and V 2C MIB I MIB II RFC1213 Firmware upgrade by Web TFTP Remote firmware upgrade UPnP EZ Setup Wizard TRO69 remote management diagnostic TRO67 ensures product meets all ADSL IOT tests IP ToS function RFC 1349 145 STANDARDS ETHERNET STANDARDS WIRELESS STANDARDS ADSL COMPLIANCE COMPLIANCES EMISSIONS ENVIRONMENTAL SAFETY APPENDIX B Hardware Specifications Standards 802 1p bit remarking Traffic classification by port 802 1p ToS and DSCP IEEE 802 3 2005 Ethernet Access Ethernet Fast Ethernet Full duplex flow control ISO IEC 8802 3 IEEE 802 1D Spanning Tree Protocol IEEE 802 1p priority tags 802 11b 802 11g 802 11n ANSI T1 413 Issue 2 G 992 1 G dmt Annex A G 992 2 G lite Annex A G 992 3 ADSL2 G dmt bis Annex A J K L M G 992 4 ADSL2 G lite bis G 992 5 ADSL2 FCC Part 15B Class B FCC Part 68 CE Mark CCC Class B RoHS compliant 1
50. CP SETTINGS The ADSL Router includes a Dynamic Host Configuration Protocol DHCP server that can assign temporary IP addresses to any attached host requesting the service as well as a DHCP relay serivce that will route the DHCP service to other subnets than that of the unit DHCP DISABLED By selecting None you can disable DHCP on the ADSL Router Figure 36 DHCP Disabled DHCP Mode This page is used ta configure DHCP mode You can set DHCP mode to None DHCP Relay or DHCP Server 1 Set the DHCP mode ta DHCP Server if you are using this device as a DHCP server This page lists an IP address pool available to hosts on your LAN The device assigns IP addresses in the pool to hasts on your network when they request Internet access 2 Set the DHCP mode ta DHCP Relay if you are using another DHCP server to assign IP address to your hosts on the LAM You can set the IP address of the DHCP server 3 If you set the DHCP made to None the device does nat assign IP addresses to the hosts when they request an IP address LAN IP Address 192 168 2 1 Subnet Mask 255 255 255 0 DHCP Mode None k The following items are displayed on this page DHCP Mode When set to None disables DHCP on the unit 76 CHAPTER 6 LAN Settings DHCP Settings DHCP RELAY Dynamic Host Configuration Protocol DHCP can dynamically allocate an IP address and other configuration information to network clients that broa
51. DGE SETTING CHAPTER 9 Advanced Bridge Setting This feature allows you to set the bridge aging time and to enable Spanning Tree The Spanning Tree Protocol STP can be used to detect and disable network loops and to provide backup links between bridges This allows a wireless bridge to interact with other bridging devices that is an STP compliant switch bridge or router in your network to ensure that only one route exists between any two stations on the network and provide backup links which automatically take over when a primary link goes down Figure 66 Bridge Setting Bridge Setting This page is used to configure the bridge parameters In this page you can modify the settings or view some Information of the bridge and its attached ports Aging Time 300 seconds 802 1d Spanning Tree Disable Enable Apply Changes show MACs The following items are displayed on this page Ageing Time Sets the MAC address ageing time in seconds After the aging time has been reached with no traffic received the unit will delete the address from the forwarding database Default 300 seconds 802 1d Spanning Tree Enables disables the Spanning Tree Protocol on the ADSL Router Default Disabled 116 LOG SETTING CHAPTER 9 Advanced Log Setting The ADSL Router supports a logging process that controls error messages saved to memory The logged messages serve as a valuable tool for isola
52. IP Address Remote IP Address State _ Action 192 168 2 23 203 94 105 9 Enable The following items are displayed on this page Local IP Address Specifies the IP address of a computer on the local network 99 CHAPTER 8 Services NAT NAPT Settings Remote IP Address Specifies the source IP address on the WAN to allow access from Leaving this parameter blank allows access from all traffic Enable Checking this box activates the parameters configurated once added to the Current NAT Port Forwarding Table Default Enabled NAT ALG AND PASS Application Layer Gateway ALG and passthrough is a useful feature when THROUGH a host computer or server on the Local Area Network must be accessible from the Internet using specific protocols This can be necessary with certain software applications that do not function reliably through Network Address Translation Figure 53 NAT ALG and Pass Through NAT ALG and Pass Through This page is used to configure NAT ALG and pass through IPSec Pass Through k Enable L2TP Pass Through I Enable PPTP Pass Through I Enable FTP Enable H 323 I Enable SIP I Enable RTSP I Enable ICQ I Enable MSN I Enable The following items are displayed on this page 9 9 IPSec Pass Through Enables IPsec passthrough Default Enabled L2TP Pass Through Enables L2TP passthrough default Enabled PPTP Pass Through Enables PPTP passt
53. MI AND SAFETY EEC SMC contact for these products in Europe is SMC Networks Europe C Fructu s Gelabert 6 8 29 2a Edificio Conata II 08970 Sant Joan Desp Barcelona Spain This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures NATIONAL RESTRICTIONS This device is intended for home and office use in all EU countries and other countries following the EU directive 1999 5 EC without any limitation except for the countries mentioned below Country Restriction Reason Remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use Military Radiolocation use Refarming of the 2 4 GHz limited to 10 mW band has been ongoing in recent years to allow e i r p within the current relaxed regulation Full implementation band 2454 2483 5 planned 2012 MHz italy None If used outside of own premises general authorization is required Luxembourg None General authorization required for network and service supply not for spectrum Norway Implemented This subsection does not apply for the geographical T within a radius of 20 km from the centre of Ny lesund Russian None Only for indoor applications Federation Gi NorE Do not use the product outdoors in France COMPLIANCES EUROPE EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R amp T
54. NETWORKS USER GUIDE ADSL2 BARRICADE N 4 Port ADSL ADSL2 Wireless Router SMC 7904WBRAS N2 v2 4 Port ADSL ADSL2 Wireless Router User Guide SMC Networks No 1 Creation Road III Hsinchu Science Park 30077 Taiwan R O C TEL 886 3 5770270 Fax 886 3 5780764 March 2012 Pub 149Xxxxxxxxxx SMC UG 0312 01 Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright 2012 by SMC Networks Inc No 1 Creation Road III Hsinchu Science Park 30077 Taiwan R O C All rights reserved Trademarks SMC is a registered trademark and Barricade EZ Switch TigerStack TigerSwitch and TigerAccess are trademarks of SMC Networks Inc Other product and company names are trademarks or registered trademarks of their respective holders WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement please refer to the Support Section of the SMC Website at http www smc com COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to c
55. Proxy Configuration RIP Configuration ARP Binding Configuration Bridge Setting Log Setting 22 FIGURES 69 70 73 74 76 77 78 79 80 82 84 86 89 89 90 92 93 95 98 J9 99 100 101 102 102 103 105 106 107 108 109 112 113 114 116 117 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 Figure 75 Figure 76 Figure 77 Figure 78 Figure 79 Figure 80 Figure 81 Figure 82 Figure 83 Figure 84 Figure 85 Figure 86 Figure 87 Figure 88 Figure 89 Figure 90 Routing Configuration UPnP SNMP Configuration System Time Configuration Other Advanced Configuration Port Mapping Configuration Diagnostic Test Ping Ping Result Ping6 Traceroute Traceroute Result ADSL Tone Diagnostics Commit Reboot Rebooting Backup Restore Settings Password Setup Upgrade Firmware TR 069 Configuration RJ 45 Connector Straight through Wiring Crossover Wiring RJ 11 Wiring 23 FIGURES 118 120 121 122 123 124 126 127 127 127 128 129 130 133 133 134 135 136 137 147 148 149 150 Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 TABLES LED Display Indicators Configuration Menu LED Troubleshooting Chart Web Access Troubleshooting Chart 10 100BASE TX MDI and MDI X Port Pinouts RJ 11 Port Pinouts OA 28 37 141 142 148 150 SECTION I GETTING STARTED This section provides an overview of the ADSL Gate
56. Selected Keyword URL Blocking Table Select Filtered Keyword L1 cnn L1 bbc The following items are displayed on this page URL Blocking Capability Enables or disables URL blocking Default Enabled Apply Changes Implements the selected URL blocking Keyword Specifies a string that traffic is to be blocked from May be in the form of a text or number string with no spaces Add Keyword Adds a defined URL keyword to the blocking table 107 CHAPTER 8 Services Software Forbidden SOFTWARE FORBIDDEN The Software Forbidden page enables traffic from listed application software to be blocked by the router Figure 61 Software Forbidden Settings Software Forbidden This page is used to config same softwares to be forbidden By it you can deny the ip packets from the specified software Current Forbidden Software List i MSN messenger Yahoo Messenger Add Forbidden Software The following items are displayed on this page Current Forbidden Software List Software applications that are currently blocked by the router Add Forbidden Software Lists pre defined software applications that can be added to the Forbidden Software table 108 DoS CHAPTER 8 Services DoS Denial of Service DoS is an attempt by a hacker to flood an IP address domain or server with repeated external communincation requests effectively saturating the system wi
57. Settings 57 Wireless Security Setup 59 Common Wireless Parameters 59 WEP Security 60 WPA Security 62 Access Control 63 Wi Fi Protected Setup WPS 65 MBSSID 66 WDS 68 6 LAN SETTINGS 72 LAN Interface 73 IPv6 LAN Configuration 74 DHCP Settings 76 DHCP Disabled 76 DHCP Relay 77 DHCP Server 78 DHCP Static IP 80 17 CONTENTS 7 WAN SETTINGS 81 Channel Configuration 82 ATM Settings 84 ADSL Settings 86 8 SERVICES 88 DNS Settings 89 DNS Server 89 IPv6 DNS 89 DDNS 90 Access Control Lists 92 LAN ACLs 92 WAN ACLs 93 IP Port Filtering 95 NAT NAPT Settings 97 Virtual Servers 97 NAT Exclude IP 99 NAT Forwarding 99 NAT ALG and Pass Through 100 NAT Port Trigger 101 FTP ALG Configuration 102 NAT IP Mapping 102 Quality of Service 103 MAC Filtering 105 DMZ 106 URL Blocking 107 Software Forbidden 108 DoS 109 IGMP Proxy Configuration 111 RIP Configuration 113 ARP Binding Configuration 114 9 ADVANCED 115 Bridge Setting 116 Log Setting 117 Routing Configuration 118 UPnP 120 SNMP Protocol Configuration 121 18 SECTION lll 10 11 System Time Configuration Other Advanced Configuration Port Mapping DIAGNOSTICS Diagnostic Test Ping Ping6 Traceroute ADSL Tone Diagnostics ADMINISTRATION SETTINGS Commit Reboot Backup Restore Settings Password Setup Upgrade Firmware TR 069 Configuration APPENDICES TROUBLESHOOTING Diagnosing Gateway Indicators If You Cannot Connect to the Internet Proble
58. T Defines the connection from the ADSL Router to the ACS User Name The user name the remote ACS should use when connecting to this device Password The password the remote ACS should use when connecting to this device Path The path of the device ConnectionRequestURL The device ConnectionRequestURL should be configured based on the Device IP Path and Port as follows http Device IP Port Path Port The port of the device ConnectionRequestURL DEBUG Sets options for displaying debug messages for the ACS connection ACS Certificates CPE Selects if digital certificates are used on the CPE Show Message Displays ACS SOAP messages on the serial console CPE sends GetRPC The router contacts the ACS to obtain Remote Procedure Call methods q 95 CHAPTER 11 Administration Settings TR 069 Configuration Skip MReboot Specifies whether to send an MReboot event code in the inform message Delay Specifies whether to start TR 069 after a short delay Auto Execution Specifies whether to automatically start TR 069 after the router is powered on CERTIFICATE MANAGEMENT Defines the digital certificate files used for authentication between the ADSL Router and the ACS CPE Certificate Password The password to use with the ADSL Router s digital certificate file CPE Certificate The unique digital security certificate used by the ADSL Router to a
59. TE Directive 1999 5 EC The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R amp TTE Directive 1999 5 EC EN 60950 1 2006 A11 2009 A1 2010 A12 2011 Safety of Information Technology Equipment EN 300 328 V1 7 1 2006 10 Electromagnetic compatibility and Radio spectrum Matters ERM Wideband transmission systems Data transmission equipment operating in the 2 4 GHz ISM band and using wide band modulation techniques Harmonized EN covering essential requirements under article 3 2 of the R amp TTE Directive EN 301 489 17 V1 8 1 2008 04 EN 301 489 17 V2 1 1 2009 05 Electromagnetic compatibility and Radio spectrum Matters ERM Electromagnetic Compatibility EMC standard for radio equipment and services Part 17 Specific conditions for 2 4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment EN 55022 2006 A1 2007 Limits and methods of measurement of radio disturbance characteristics of information technology equipment EN 55024 1998 A1 2001 A2 2003 Information technology equipment immunity characteristics limits and methods of measurement EN 62311 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields 0 Hz 300 GHz This device is a 2 4 GHz wideband transmission system transceiver intended for use in all EU member states and EFT
60. The ADSL Gateway Router needs to be connected to the DSL telephone line from the service provider and to a computer or LAN switch Figure 4 Connecting the Router i G 2 L 9 WLAN WPS LAN1 LAN2 LAN3 LAN4 Power ON OFF T 3 Telephone Wall Jack AC Power Outlet Standard Telephone AC Power Cable Adapter Category 5 UTP Cable e Telephone NY Computer Splitter To install the router follow these steps 1 Using standard telephone cable connect the Line port on the included ADSL splitter to the RJ 11 telephone wall jack providing the ADSL service 2 Using standard telephone cable connect the Modem port on the included ADSL splitter to the RJ 11 Line port on the ADSL Gateway Router 31 CHAPTER 2 Installing the Router Powering On 3 The Phone port on the ADSL splitter can be connected to a standard telephone set using telephone cable 4 Connect one end of the included Ethernet cable to an Ethernet port on the ADSL Gateway Router and the other end to a PC s RJ 45 network port Alternatively you can connect an Ethernet port to a LAN switch CAUTION Do not plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Note When connecting to any network device such as a PC hub or switch you can use either straight through or crossover cabling Refer to Cables a
61. WDS Add WDS AP MAC Address Comment Current WDS AP List MAC Address 00 1f a4 90 f3 1d d Delete Selected Delete All To set up WDS all connected routers should be in the same subnet with DHCP disabled on all routers not connected to the WAN and the MAC address of each router set first Follow the steps detailed below 1 The wireless setup must be the same on all connected routers 68 CHAPTER 5 WLAN Configuration WDS Figure 31 WDS Wireless Setup Wireless Basic Settings This page is used to configure the parameters for your wireless network Disable Wireless LAN Interface Band 24 GHz B G N v Mode APSWDS SSID Channel Width Control Sideband adds Current Channel 11 Radio Power Percent Associated Clients Show Active Clients Apply Changes 2 The MAC addresses on all connected routers must be set 3 Change the LAN address on routers so as to avoid an IP conflict Figure 32 LAN Basic Setup LAN Interface Setup This page is used to configure the LAN interface of vour ADSL Router Here you may change the setting for IP addresss subnet mask etc Interface Name el IP Address 192 168 2 2 Subnet Mask 255 255 255 Secondary IP IGMP Snooping Disable Enable Apply Changes 69 CHAPTER 5 WLAN Configuration 4 DIsable the DHCP server Figure 33 Disabling DHCP DHCP Mode
62. a at up to 1 5 Mbps downstream and 512 Kbps upstream This ADSL option can be installed without an on site visit by the service provider G dmt A standard that defines full rate ADSL and utilizes Discrete Multi Tone DMT signaling to transmit data at up to 8 Mbps downstream and 640 Kbps upstream 71 413 ANSI standard that defines the requirements for ADSL for the interface between the telecommunications network and the customer installation in terms of their interaction and electrical characteristics The Gateway complies with Issue 2 of this standard 86 CHAPTER 7 WAN Settings ADSL Settings m ADSL2 This standard extends the capability of basic ADSL data rates to 12 Mbit s downstream and 3 Mbit s upstream with a mandatory capability of ADSL2 transceivers of 8 Mbit s downstream and 800 Kbit s upstream ADSL2 This standard extends the capability of basic ADSL data rates to 24 Mbit s downstream and 1 4 Mbit s upstream depending on the distance from the DSLAM to the customer s home AnnexL Option Annex L is an optional specification in the ITU T ADSL2 recomendation G 992 3 titled Specific requirements for a Reach Extended ADSL2 READSL2 system operating in the frequency band above POTS It is often referred to as Reach Extended ADSL2 or READSL2 Once enabled AnnexL increases the range of DSL service enabling the link to work at a distance of 7 kilometers or 23 000 feet AnnexM Option
63. ally friendly policy throughout the entire production process This is achieved though the following means Adherence to national legislation and regulations on environmental production standards Conservation of operational resources Waste reduction and safe disposal of all harmful un recyclable by products Recycling of all reusable waste content Design of products to maximize recyclables at the end of the product s life span Continual monitoring of safety standards END OF PRODUCT LIFE SPAN This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life MANUFACTURING MATERIALS There are no hazardous nor ozone depleting materials in this product DOCUMENTATION All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests The inks used in the printing process are non toxic 14 PURPOSE AUDIENCE CONVENTIONS A PN REVISION HISTORY ABOUT THIS GUIDE This guide gives specific information on how to install the ADSL Gateway Router and its physical and performance related characteristics It also gives information on how to operate and use the management functions of the ADSL Gateway Router This guide is for users with a basic working knowledge of computers You should be familiar with Windows operating system concepts
64. and drain power faster Using higher DTIM values reduces the power used by stations in Power Save mode but delays the transmission of broadcast multicast frames Range 1 255 beacons Default 1 beacon Data Rate The maximum data rate at which the wireless interface transmits multicast and broadcast packets Options Auto 1 2 5 5 11 6 9 18 24 36 48 54 Mbps Default Auto Preamble Type Sets the length of the signal preamble that is used at the start of a data transmission Default Long Long Preamble Sets the preamble to long 192 microseconds Using a long preamble ensures the wireless interface can support all 802 11b and 802 11g clients Short Preamble Sets the preamble according to the capability of clients that are currently asscociated Uses a short preamble 96 microseconds if all associated clients can support it otherwise a long preamble is used The wireless interface can increase data throughput when using a short preamble but will only use a short preamble if it determines that all associated clients support it Broadcast SSID Enables disables the wireless interface to broadcast an SSID service set identifier to uniquely identify it on the network Aggregation This option enables Mac Service Data Unit MSDU aggregation Default Enabled Short GI The guard interval between symbols helps receivers overcome the effects of multipath delays You can enable a short interval to in
65. ceived and transmitted packet statistics for all interfaces on the ADSL Router Figure 18 Status DSL Statistics ADSL Statistics This page shows the ADSL settings of the device ADSL Line Status ACTIVATING ADSL Mode Upstream Downstream Attenuation Downstream db Attenuation Upstream db SNR Margin Downstream db SNR Margin Upstream db Vendor ID RETK DSP Version 2918b224 CRC Errors Upstream BER Downstream BER Up Output Power Down Output Power ES SES UAS ADSL Retrain The following items are displayed on this page ADSL Status Displays the ADSL connection status activating up or null ADSL Mode Displays the connection mode for the ADSL Router which is fixed at ADSL2 Upstream Displays the actual payload carried on the upstream channels Downstream Displays the actual payload carried on the downstream channels Attentuation Downstream Upstream db Displays the amount of attenuation in signal strength due to conductive losses in transmission medium Attenuation affects the propagation of waves and signals in electrical circuits expressed in decibels dB 51 CHAPTER 4 Device Information ARP Table SNR Margin Downstream Upstream db Displays the current Signal to noise margin expressed in decibels dB SNR is the ratio of Signal power to the noise power corrupting the signal Vendor ID The vendor name of the digital signal
66. crease throughput Default Enabled 58 CHAPTER 5 WLAN Configuration Wireless Security Setup WIRELESS SECURITY SETUP Describes the wireless security settings for each VAP including association mode encryption and authentication Figure 22 Wireless Security Setup None Wireless Security Setup This page is used to configure wireless security mode Set the encryption mode to VVEP or WPA which prevents any unauthorized access to your wireless network SSID Type Root OVAPO OVAP1 OVAP2 OVAP3 Encryption WPA TKIP v Use 802 1x Authentication WEP 64bits WEP 128bits WPA Authentication Mode Enterprise RADIUS Personal Pre Shared Key Pre Shared Key Format _Passphrase v Pre Shared Key pe Authentication RADIUS Port 1812 IP address Password Server Note When encryption WEP is selected you must set WEP key value Apply Changes COMMON WIRELESS The following items are displayed all pages of the Wireless Security Setup PARAMETERS SSID TYPE Selects the VAP to apply security settings to Options Root VAPO VAP3 Encryption Selects the encryption type to deploy on the specified VAP The options are 2 None No security WEP WEP is used as the multicast encryption cipher You should select WEP only when both WPA and WEP clients are supported WPA TKIP AES WPA employs a combination of several technologies to provide an enhanced security solution for 802 11
67. d Configuration Here you can set other miscellaneous advanced settings Half Bridge When enable Half Bridge that PPPoE PRPPoA s connection type will set to continuous Half Bridge Disable Enable Interface The following items are displayed on this page Half Bridge Displays the current date and time and allows you to manually configure time settings Interface Selects the WAN interface for the Half Bridge feature 123 CHAPTER 9 Advanced Port Mapping PORT MAPPING Port Mapping supports multiple ports to WAN interfaces and bridging groups Each group performs as an independent network You can create up to four groups on the router Figure 73 Port Mapping Configuration Port Mapping Configuration The procedure for operating a mapping group is as follows 1 Enable port mapping 2 Select a group from the table 3 Select interfaces from the available interface list and add it to the grouped interface list by using the arrow buttons to bind the ports 4 Click Apply Changes to save the settings Note The selected interfaces will be removed from their original groups and added to the new group Disable C Enable WAN Interface Group EN NNNM NN Default LAN1 USBO Enabled Group C es Group2 Group3 Group4 Apply Changes The following items are displayed on this page WAN The WAN interfaces that can be grouped
68. d Time 4294967295 600 4294967295 5 Apply Changes DHCPv6 Setting DHCP v6 Mode Manual Mode v IPv6 Address Pool Prefix Length 64 Preferred Time 120 Valid Time 120 DNS Servers fe8D 1 Apply Changes 7 4 CHAPTER 6 LAN Settings IPv6 LAN Configuration The following items are displayed on this page RA SETTING Enable Enables IPv6 router advertisements on the router M Flag Sets the router advertisement Managed address configuration flag When set the router will use DHCPv6 to obtain stateful addresses O Flag Sets the router advertisement other stateful configuration flag When set the router will attempt to acquire other non address configuration information such as a default gateway or DNS Max Interval The amount of time that a remote IPv6 node is considered reachable Min Interval The interval between transmitting IPv6 neighbor solicitation messages Prefix Mode Enables manual or automatic configuration of IPv6 addresses on the router m Auto Enables automatic configuration of IPv6 addresses on interfaces and enables IPv6 functionality on the router The network portion of the address is based on prefixes received in IPv6 router advertisement messages and the host portion is automatically generated using the modified EUI 64 form of the interface identifier that is the router s MAC address Manual If auto configuration is not selected
69. dcast a request To receive the broadcast request the DHCP server would normally have to be on the same subnet as the client However when the access point s DHCP relay agent is enabled received client requests can be forwarded directly by the access point to a known DHCP server on another subnet Responses from the DHCP server are returned to the access point which then broadcasts them back to clients Figure 37 DHCP Relay DHCP Mode This page is used to configure DHCP mode You can set DHCP made to None DHCP Relay or DHCP Sever 1 Set the DHCP made to DHCP Server if you are using this device as a DHCP server This page lists an IP address pool available ta hosts on your LAN The device assigns IP addresses in the pool to hosts on your network when they request Internet access 2 Set the DHCP made to DHCP Relay if you are using another DHCP server to assign IP address to your hosts on the LAN You can set the IP address of the DHCP server 3 If you set the DHCP mode to None the device does not assign IP addresses to the hosts when they request an IP address LAN IP Address 182 158 2 1 Subnet Mask 255 255 255 0 DHCP Mode DHCP Relay Relay Server 182 158 2242 Apply Changes The following items are displayed on this page DHCP Mode When set to DHCP Relay enables routing of the DHCP service to units on a different subnet Relay Server Enter the address of the DHCP server for routing t
70. ddress Destination Port Specifies a range of ports to block traffic from the specified LAN IP address from reaching Apply Changes Adds a newly configured packet filter that denies forwarding in to the local area network to the list CURRENT FILTER TABLE The Current Filter Table displays the configured IP addresses and ports that are permitted or denied access to and from the ADSL Router 99 gt 9 Rule Displays if the specified traffic is allowed or denied Protocol Displays the destination port type Source IP Mask Displays the source IP address SPort Displays the source port range Dest IP Mask Displays the destination IP address DPort Displays the destination port range State Indicates if an entry is enabled Direction Displays the direction in which the rule has been applied Action Enables disables or deletes the selected entry from the table 96 CHAPTER 8 Services NAT NAPT Settings NAT NAPT SETTINGS VIRTUAL SERVERS Network Address Translation NAT is a standard method of mapping multiple internal IP addresses to one external IP address on devices at the edge of a network For the router the internal local IP addresses are the IP addresses assigned to local PCs by the DHCP server and the external IP address is the IP address assigned to the specified WAN interface The NAT function on the router enables the support
71. e Router Configuring the TCP IP Protocols 4 Select TCP IP from the list of network protocols this may include details of adapters installed in your computer 5 Click Properties 6 Check the option Obtain an IP Address WiNDOWS 2000 1 Click Start Settings Network Dial up Connections 2 Click Local Area Connections 3 Select TCP IP from the list of network protocols 4 Click on Properties 5 Select the option Obtain an IP Address WINDOWS XP 1 Click Start Control Panel Network Connections 2 Right click the Local Area Connection icon for the adapter you want to configure 3 Highlight Internet Protocol TCP IP 4 Click on Properties 5 Select the option Obtain an IP address automatically and Obtain DNS server address automatically WINDOWS VISTA 1 Click Start Control Panel 2 Double click Network and Sharing Center 3 Click View status 4 Click Properties If the User Account Control window appears click Continue 5 Highlight Internet Protocol Version 6 TCP IPv6 or Internet Protocol Version 4 TCP IPv4 and click Properties 6 Select the option Obtain an IP address automatically and Obtain DNS server address automatically MAc OS 1 Pull down the Apple Menu Click Control Panels and select TCP IP 2 In the TCP IP dialog box verify that Ethernet is se
72. e drop down menu Options are DynDns or TZO Default DynDns org Host Name Specifies the prefix to identify your presence on the DDNS server either URL or IP address Interface Selects the WAN interface for the DDNS service 90 CHAPTER 8 Services DNS Settings Enable Enables DDNS Default Enabled DYNDNS SETTINGS The following parameters apply to the default DynDns setting User Name Specifies your username for the DDNS service Password Specifies your password for the DDNs service TZO The following parameters apply to the TZO setting Email Specifies your contact email address for the DDNS service Key Specifes an encryption key for the DDNS service DvNAMIC DDNS TABLE This table displays the configured servers in the DDNS setup Select Highlights an entry in the Dynamic DDNS Table State Displays the state of the server entry enabled or disabled Service Displays the type of DDNS service Host Name Displays the URL or IP address of the DDNS service provider User Name Displays the user name or contact email of the DDNS user Interface The WAN interface for the DDNS service 91 CHAPTER 8 Services Access Control Lists ACCESS CONTROL LISTS LAN ACLs The ADSL Router supports Access Control Lists that filter IP addresses allowed access on the unit s LAN and WAN interfaces Only traffic fr
73. e is used to configure Wi Fi protected setup VVPS Using this feature could let your wireless client automatically syncronize its setting and connect to the access point AP in 2 minutes without any hassle Disable WPS WPS Status Configured UnConfigured Self PIN Number 15880611 Regenerate PIN Push Button Configuration Start PBC Apply Changes Current Key Info Authentication _Encryption Key Open None N A Client PIN Number Start PIN The following items are displayed on this page Disable WPS Disables WPS configuration Default Disabled WPS Status Displays if there is currently any WPS traffic connecting to the router Self PIN Number Displays the PIN Code for the router The default is exclusive for each unit Regenerate PIN Click the button to generate a new PIN number that is used by the router Push Button Configuration The Start PBC button has the same effect as pressing the physical WPS button that is located on the rear of the router After clicking on the button you have up to two minutes to activate WPS on a device that needs to join the network Apply Changes Applies the current WPS settings 65 MBSSID CHAPTER 5 WLAN Configuration MBSSID Reset Resets the WPS settings to factory default values Client PIN Number Enters a PIN number of a wireless client device that needs to join the network Click Start PIN to activate
74. e upgrades Support of up to 8 Permanent Virtual Circuits PVC Support of up to 8 PPPoE sessions ER CHAPTER 1 Introduction Description of Hardware DESCRIPTION OF HARDWARE This ADSL Gateway Router is a high bit rate Digital Subscriber Line DSL modem that can connect to an ADSL Internet service provider This unit provides the following ports on the rear panel One RJ 11 port for connection to your ADSL service provider s incoming line Four RJ 45 ports for connection to PCs or to a 10 100BASE TX Ethernet Local Area Network switch The ports operate at 10 100 Mbps half full duplex It supports automatic MDI MDI X operation so you can use straight through cables for all network connections See 10 100BASE TX Pin Assignments on page 148 The following two figures show the components of the Gateway Figure 1 Top Panel 27 Figure 2 Rear Panel WAN Port Figure 3 Front Panel LEDs ADSL2 2 Router WLAN On Off CHAPTER 1 Introduction Description of Hardware _ LAN1 LAN2 LAN3 LAN4 Power ON OFF Reset Button Power DSL WPS Button Ethernet Ports Power Socket and On Off Switch Internet LAN _ WLAN WPS The ADSL Gateway Router includes key system and port indicators that simplify installation and network troubleshooting The LEDs which are located on the top of the unit for easy viewing are described in the following table Table 1 LED Display Indicat
75. ecify the IP address of a public time server select your local time zone and click Next Figure 8 Wizard Step 2 Time Zone Configuration 2 Time Zone This page allows you to configure the localized time zone amp automatic time maintenance Automatic time maintenance synchronizes the Barricade with a public time server on the Internet SMC recommend to use this function click the Next button to continue NTP Configuration State 8 Disable Enable Server IP 132 163 4 102 v Interval Every hours Time Zone GMT Gambia Liberia Morocco England Im GMT time Thu Jan 1 4 6 6 1970 The following items are displayed on this page Status Enables or disables time synchronization with external servers 40 CHAPTER 3 System Configuration Setup Wizard Server IP Specifies the IP address of a public NTP time server on the Internet Interval Specifies the time interval for polling the NTP server Time Zone A drop down box provides access to predefined time zones Each choice indicates it s offset from GMT and lists at least one major city or commonly known zone name covered by the time zone STEP 3 ADSL The third page of the wizard configures the ADSL country settings Internet SETTINGS service provider protocol connection type and username and password Figure 9 Wizard Step 3 ADSL Settings 3 ADSL Settings This page allows you to configure the ADSL setting
76. entry to the table Range 0 255 Default 0 84 CHAPTER 7 WAN Settings ATM Settings VCI Virtual Channel Identifier Adds a VCI entry to the table Range 32 65535 Default 35 QoS Selects packet level Quality of Service QoS for the connection Options are UBR Unspecified Bitrate Configures a PVC with a Peak Cell Rate indicating the maximum number of ATM cells that can be sent in a burst CBR Constant Bitrate Configures a PVC at a constant bit rate This option may be required for connections that depend on precise clocking to ensure undistorted delivery nrt VBR non realtime Variable Bitrate Configures a PVC at a non realtime variable bit rate This option may be used for applications not sensitive to changes in available bandwidth such as data rt VBR realtime Variable Bitrate Configures a PVC at a real time variable bit rate This option may be used for applications that have a lot of variance in required bandwidth such as voice PCR Peak Cell Rate Configures the maximum allowable rate at which cells can be transported along a connection in the ATM network The PCR is the determining factor in how often cells are sent in relation to time in an effort to minimize jitter CDVT Cell Delay Variation Tolerance Configures the maximum amount of jitter permissable SCR Sustainable Cell Rate Configures the average allowable long term cell transfer rate on a specific c
77. er a static pre shared key or 802 1X authentication through a RADIUS server Either TKIP or AES encryption is used depending on the client STEP 4 The final step in the setup wizard saves the configuration changes Click CONFIGURATION Finish to complete the wizard then click Save SAVING _ Figure 11 Wizard Step 3 Configuration Saving 5 Configuration Saving Click Finish to save these settings Click Back to make any modifications Click Reset to drop these settings The parameters you set NTP State Disable VPI VCI 55 Encapsulation LLC SNAP Channel Mode pppoe ppp User Name passnet ppp Password passnet DNS Settings Obtain DNS Automatically WLAN Interface Enable 44 SYSTEM STATUS DEVICE INFORMATION The Status pages display information on hardware software versions LAN and WAN connection status statistics and the ARP table The System Status page displays the hardware and software versions and the WAN connection status and speed Click Status System Figure 12 System Status System Status This page shows the current status and some basic settings of the device System SMC7904WBRAS N2 v2 Uptime hh mm ss 0 4 41 26 DSP Version 2920b804 DSL Operational Status Upstream Speed E Downstream Speed 2 SMC7904WBRAS N2 v2 v1 0 0 0 The following items are displayed on this page SYSTEM Alias Name An alias for the ADSL Router enabling the device
78. ess to the ADSL Router Services Allowed Specifies services that are allowed access from LAN interfaces or allows any 93 CHAPTER 8 Services Access Control Lists Add Adds the ACL to the ACL Table CURRENT ACL TABLE Lists the configured ACLs on the LAN ports 9 9 9 Select The number of the entry in the table Direction Displays if the ACL is applied to a LAN or WAN interface IP Address Interface Displays the allowed IP address or range Service Dispays the allowed service Port Displays the TCP UDP port of the allowed service Action Click the button to remove the entry from the table 94 CHAPTER 8 Services IP Port Filtering IP PORT FILTERING IP Port filtering restricts connection parameters to limit the risk of intrusion and defends against a wide array of common hacker attacks IP Port filtering allows the unit to permit deny or proxy traffic through its ports and IP addresses Figure 49 IP Port Filtering Settings IP Port Filter Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Outgoing Default Action Permit Deny Incoming Default Action Permit Deny Rule Action Permit Deny Protocol P B Direction Upstream xi Source IP Address Subnet Mask 255 255 255 255
79. eway and subnet mask When DHCP is 83 ATM SETTINGS CHAPTER 7 WAN Settings ATM Settings selected the WAN interface IP address is assigned by the remote DHCP server Local IP address The IP address of the WAN interface provided by the ISP Gateway The IP address of the remote gateway router provided by the ISP WNetmask The subnet mask for the local IP address Default Route Enables or disables the default route IP address Unnmbered Enables the IP unnumbered feature The ATM Settings page is used to configure the settings between your ADSL Router and the remote ATM PVC switch including connection mode single or multiple service over one connection and packet level QoS The ATM Settings parameters form a Traffic Contract that informs the network what type of traffic is to be transported and the performance requirements of the traffic Figure 42 ATM Settings ATM Settings This page is used to configure the parameters for the ATM of your ADSL Router Here you may change the setting for QoS PCR CDVT SCR and MBS VPI Vel Qos UBR v PCR CDVT SCR MBS Current ATM VC Table Select VPl VCI QoS PCR CDVT SCR 0 32 UBR 6144 0 I The following items are displayed on this page Select Clicking the radio button associated with the connection makes the parameters editable VPI Virtual Path Identifier Adds a VPI
80. figuration Menu Continued Menu Description Page Statistics Shows the network traffic statistics 50 DSL Statistics Shows the ADSL line statistics 51 ARP Shows entries in the ARP table 52 Wireless Basic Settings Configures basic wireless settings 55 Advanced Settings Configures advanced wireless settings 57 Security Configures wireless security settings 59 Access Control Configures wireless access control settings 64 WPS Configures WPS security 65 MBSSID Enables multiple SSID interfaces 66 WDS Configures Wireless Distribution System settings 68 LAN Interface LAN Interface Configures the LAN management interface including IP 73 address and IGMP snooping on LAN side IPv6 LAN Config Configures IPv6 LAN settings 74 DHCP Config DHCP Mode Sets DHCP server and DHCP relay settings 76 Static IP Configures static DHCP assignments 80 WAN Interface Channel Config Configures the DSL channel settings 82 ATM Settings Configures DSL ATM settings 84 ADSL Settings Configures ADSL settings 86 Services DNS DNS Server Configures DNS server settings 89 IPv6 DNS Configures IPv6 DNS server settings 89 Dynamic DNS Configures DDNS settings 90 Access Control List ACL Config Configures ACLs for LAN or WAN interfaces 92 IP Port Filtering Configures IP filtering settings 95 NAT NAPT Virtual Server Configures the virtual server forwarding table 97 NAT Exclude IP Configures excluded IPs on the WAN interface 99 NAT Forwarding Configures forwarding
81. for access to local servers 99 NAT ALG and Pass Configures NAT passthrough for specific application 100 Through protocols NAT Port Trigger Restricts Internet access for specific ports 101 38 CHAPTER 3 System Configuration Using the Web Interface Table 2 Configuration Menu Continued Menu Description Page FTP ALG Configures FTP server and client ports 102 Configuration NAT IP Mapping Configures IP address mapping for NAT 102 IP QoS Configures IP based QoS settings 103 MAC Filtering Configures MAC address filtering 105 DMZ Configures DMZ settings 106 URL Block Sets URL key words to block 107 Software Forbidden Blocks Internet access for specific software 108 DoS Setting Configures denial of service settings 109 IGMP Proxy Configures IGMP Proxy settings for multicast traffic 111 RIP Configures Routing Information Protocol settings 113 ARP Binding Configures Address Resolution Protocol binding 114 Advance Bridge Setting Configures aging time and Spanning Tree settings 116 Log Setting Configures system log settings 117 Routing Configures static routing 118 UPnP Enables UPnP for the WAN interface 120 SNMP Configures SNMP settings 121 System Time Configures NTP time server settings 122 Others Configures Half Bridge settings 123 Port Mapping Maps LAN ports to WAN interfaces 124 Diagnostic Diag Test Runs diagnostic tests for the ADSL link 126 Ping Sends Ping echo requests to other devices 127 Ping6 Sends IPv6
82. g the port IP Spoof Prevents a situation where a hackerby a hacker creates an alias spoof of the units IP address to which all traffic is redirected IP Teardrop Prevents a Teardrop attack that involves sending mangled IP fragments with overlapping over sized payloads to the unit The fragmented packets are processed by the unit causing it to crash PingofDeath Prevents the receival of an oversized ping packet that the unit cannot handle Normal ping packets are 56 bytes or 84 bytes with the IP header attached The Ping of Death will exceed the maximum IP packet size of 65 535 bytes TCP Scan Prevents the probing of the unit by a hacker for open TCP ports to then block 110 CHAPTER 8 Services IGMP Proxy Configuration TCP SynWithData Prevents the hacker sending a volume of requests for connections that cannot be completed UDP Bomb Also called a UDP Flood or packet storm Prevents the hacker congesting the network by generating a flood of UDP packets between it and the unit using the UDP chargen service a testing utility that generates a character string for every packet it receives UDP EchoChargen Prevents the hacker from sending a UDP packet to the echo server with a source port set to the chargen port m packets second Enter the number of packets per second that you want to scan for malicious activity Sensitivity Specifies the sensivity of the TCP UDP port scan prevention Options High
83. going vor UDP mf outgoing 1 Jc Ee Ee dE Apply Changes Current Portrigger Table Trigger Protocol Direction Match Port Open Protocol Relate Port Action QuickTime 4 Client tcp outgoing 554 554 udp 6970 32000 QuickTime 4 Client tcp outgoing 554 554 udp 6970 7000 The following items are displayed on this page Port Trigger Enables the feature Default Disabled Application Type Select a name from the list of common applications or set a custom name to describe the service Start End Match Port Specifies the trigger port range Range 1 65535 Trigger Protocol Specifies the trigger port type used TCP UDP or both Start End Relate Port Specifies the public port range Range 1 65535 Open Protocol Specifies the public port type used TCP UDP or both NAT Type Specifies outgoing or incoming traffic 101 CHAPTER 8 Services NAT NAPT Settings FTP ALG FTP ALG Configuration specifies a non standard FTP port for passthrough CONFIGURATION traffic The standard port for FTP connections is TCP port 21 and the router monitors port 21 to ensure the NAT passthrough of FTP When the FTP server port is not 21 you must specify the TCP port to ensure NAT passthrough of FTP Figure 55 NAT FTP ALG Configuration FTP ALG Configuration This page is used ta configure FIP Server ALG and FTP
84. hadigte Kabel und Stecker k nnen Stromschlage und Brand verursachen Pr fen Sie die Netzkabel regelmabig Ersetzen Sie sie umgehend falls sie beschadigt sind Achten Sie zur Vermeidung von Gerateschaden aufgrund von berhitzung darauf dass gen gend Freiraum zur W rmeabfuhr vorhanden ist Die Bel ftungs ffnungen am Gerat dienen der Warmeabfuhr und damit der Gewahrleistung eines normalen Ger tebetriebs Decken Sie diese Bel ftungs ffnungen nicht ab 11 COMPLIANCES Stellen Sie dieses Ger t nicht in der Nahe von Warmequellen oder an Orten mit hohen Temperaturen auf Platzieren Sie das Gerat nicht im direkten Sonnenlicht Stellen Sie dieses Gerat nicht an feuchten oder nassen Orten auf Achten Sie darauf keine Fl ssigkeiten ber dem Gerat zu versch tten Befolgen Sie die Hinweise im Benutzerhandbuch bzw in der Kurzanleitung zum Anschlu des Ger tes an einen PC oder ein anderes Elektrogerat Jegliche unzul ssige Verbindung birgt die Gefahr von Stromschlagen und Brandgefahr Platzieren Sie dieses Gerat nicht auf einer instabilen Oberflache oder Halterung PRECAUCIONES DE SEGURIDAD Lea la siguiente informaci n detenidamente antes de utilizar el dispositivo Siga las indicaciones de precauci n que se mencionan a continuaci n para proteger el dispositivo contra riesgos y dafios causados por el fuego y la energ a el ctrica Utilice el adaptador de alimentaci n incluido en el paquete del dispositivo
85. hrough Default Enabled FTP Enables FTP passthrough Default Enabled H 323 Enables H 323 Windows Netmeeting passthrough Default Enabled SIP Enables SIP passthrough Default Enabled RTSP Enables RTSP passthrough Default Enabled ICQ Enables ICQ passthrough Default Enabled 100 CHAPTER 8 Services NAT NAPT Settings MSN Enables MSN passthrough Default Enabled NAT PORT TRIGGER Port triggering is a way to automate port forwarding in which outbound traffic on predetermined ports triggering ports causes inbound traffic to specific incoming ports to be dynamically forwarded to the initiating host while the outbound ports are in use Figure 54 NAT Port Trigger Nat Portrigger Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Nat Portrigger OQ Enable Disable Apply Changes Application Type Usual Application Name Select One EN B O User defined Application Name Start Match PortEnd Match PortTrigger ProtocolStart Relate PortEnd Relate PortOpen Protocol Nat Type YDP eS UDP vl outgoing UDP 2 UDP v outgoing UDP UDP outgoing UDP UDP v outgoing E UDP i UDP outgoing UDP UDP outgoing UDP UDP out
86. ications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s This is confirmed by marking the equipment with the Industry Canada certification number The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations COMPLIANCES Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician aS appropriate CE MARK DECLARATION OF CONFORMANCE FOR E
87. ient knowledge about wireless LAN These settings should not be changed unless you know what effect the changes will have on your Access Point Authentication Type C Open System Shared Key Auto Fragment Threshold 2346 256 2346 RTS Threshold 2347 0 2347 Beacon Interval 100 20 1024 ms DTIM Interval 1 1 256 Data Rate Auto Preamble Type Long Preamble Short Preamble Broadcast SSID Enable Disable Relay Blocking Enable 9 Disable Ethernet to Wireless Blocking Wifi Multicast to Unicast Aggregation Enable Disable Short GI Enable Disable Apply Changes The following items are displayed on this page Enable Disable Enable Disable Authentication Type Sets the basic authentication method Fragment Threshold Configures the minimum packet size that can be fragmented when passing through the wireless interface Fragmentation of the PDUs Package Data Unit can increase the reliability of transmissions because it increases the probability of a successful transmission due to smaller frame size If there is significant interference present or collisions due to high network utilization try setting the fragment size to send smaller fragments This will speed up the retransmission of smaller frames However it is more efficient to set the fragment size larger if very little or no interference is present because it requires overhead to send multiple
88. lands met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Bij deze Manufacturer dat deze Radio LAN device voldoet aan de essenti le eisen en aan de overige relevante bepalingen van Richtlijn 1999 5 EC English Hereby Manufacturer declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Estonian K esolevaga kinnitab Manufacturer seadme Radio LAN device vastavust direktiivi 1999 Eesti 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele Finnish Valmistaja Manufacturer vakuuttaa t ten ett Radio LAN device tyyppinen laite on Suomi direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen French Par la pr sente Manufacturer d clare que l appareil Radio LAN device est conforme aux Fran ais exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE German Hiermit erkl rt Manufacturer dass sich dieser diese dieses Radio LAN device in Deutsch bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999 5 EG befindet BMWi Hiermit erkl rt Manufacturer die bereinstimmung des Ger tes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999 5 EG Wien Greek ue THV rrapouoca Manufacturer OnAwve ori radi
89. lected in the Connect Via field 33 CHAPTER 2 Installing the Router Configuring the TCP IP Protocols 3 If Using DHCP Server is already selected in the Configure field your computer is already configured for DHCP Otherwise select Using DHCP Server in the Configure field and close the window 4 Another box will appear asking whether you want to save your TCP IP settings Click Save 5 Your service provider will now be able to automatically assign an IP address to your computer 34 SECTION Bi WEB CONFIGURATION This section describes the basic settings required to access the web management interface and provides details on configuring the Gateway This section includes these chapters System Configuration on page 36 Device Information on page 45 WLAN Configuration on page 54 LAN Settings on page 72 WAN Settings on page 81 Services on page 88 Advanced on page 115 Diagnostics on page 125 99 gt UM Administration Settings on page 132 E cum s SYSTEM CONFIGURATION USING THE WEB INTERFACE The router provides a web based management interface for configuring device features and viewing statistics to monitor network activity This interface can be accessed by any computer on the network using a Standard web browser such as Internet Explorer 5 0 Netscape 6 2 Mozilla Firefox 2 0 or above To make an initial c
90. lue Apply Changes WEP SECURITY The following page describes the WEP security setup on the ADSL Router Figure 24 Wireless Security Setup WEP Wireless Security Setup This page is used to configure wireless security mode Set the encryption mode to WEP or VPA which prevents any unauthorized access to your wireless network SSID Type Root YAPO OVAP1 OVAP2 OVAP3 Encryption WEP w Set WEP Key Use 802 1x Authentication WEP G4bits C WEP 128bits WPA Authentication Mode Enterprise RADIUS Personal Pre Shared Key Pre Shared Key Format Pre Shared Key Authentication RADIUS Port 1812 IP address 0 0 0 0 Password Server Note When encryption WEP is selected you must set WEP key value Apply Changes 60 CHAPTER 5 WLAN Configuration Wireless Security Setup The following items are displayed on this page Set WEP Key Configures the WEP key setup This is displayed in the screen below Use 802 1x Authentication Enables disables 802 1x authentication When enabled the above screen displays WEP 64bits 128bits Selects between 64 bit and 128 bit keys RADIUS SERVER Port Specifies the port number used to communicate with the RADIUS server IP Address Specifies the IP address used to communicate with the RADIUS server Password Specifies the key necessary for RADIUS server authentication WEP KEY SETUP The following page desc
91. mc com Nederlands Technische ondersteuningsinformatie beschikbaar op www smc com Polski Informacje o wsparciu technicznym sa dostepne na www smc com CeStina Technicka podpora je dostupna na www smc com Magyar M szaki tamogat informacio elerhet on www smc com fay 278 FH XC dj ZR SITUE n i 3d www smc prc com Zr ifj SE B8 rH Nc ge indc f x HE ER BR FS RS www smcnetworks com tw Tnu enxnsnuauexaumnaenuumetiialei www smc asia com t amp d Jle lawa BAH www smcnetworks co kr S HUSA B amp L C INTERNET E mail address www smc com Support By email Driver updates www smc com Support Downloads SMC7904WBRAS N2 v2
92. mented in the wiring When auto negotiation is enabled for any RJ 45 port on this gateway you can use either straight through or crossover cable to connect to any device type Figure 89 Crossover Wiring EIA TIA 568B RJ 45 Wiring Standard 10 100BASE TX Crossover Cable White Orange Stripe A Orange N White Green Stripe S End A End B Blue White Blue Stripe ud Green White Brown Stripe Brown N ceo 4o0c0i1 i o NM AA CONOOaRWN 149 RJ 11 PORT APPENDIX C Cables and Pinouts RJ 11 Port Standard telephone RJ 11 connectors and cabling can be found in several common wiring patterns These six pin connectors can accommodate up to three wire pairs three telephone lines but usually only one or two pairs of conductor pins and wires are implemented The RJ 11 port on this device contains one wire pair an inner pair on pins 3 and 4 This wire pair carries the digital data Figure 90 RJ 11 Wiring Red or Green or Blue White White Blue R Ring T Tip Table 6 RJ 11 Port Pinouts Pin Signal Name Wire Color 1 Not used Not used Line 1 Ring Red or Blue White Line 1 Tip Green or White Blue Not used Dn Ui BR U N Not used 130 10BASE T 100BASE TX 1000BASE T BACKBONE DHCP ETHERNET FIREWALL FTP HTTP ISP GLOSSARY IEEE 802 3 2005 specification for 10 Mbps Ethernet over two pairs of Catego
93. ms Accessing the Management Interface HARDWARE SPECIFICATIONS Physical Characteristics Wireless Characteristics Software Features Standards Compliances CABLES AND PINOUTS Twisted Pair Cable Assignments 10 100BASE TX Pin Assignments Straight Through Wiring Crossover Wiring RJ 11 Port 19 CONTENTS 122 123 124 125 126 127 127 128 130 132 133 134 135 136 137 140 141 141 142 142 143 143 144 144 146 146 147 147 148 148 149 150 CONTENTS GLOSSARY 151 INDEX 154 20 Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 FIGURES Top Panel Rear Panel Front Panel LEDs Connecting the Router Web Login Home Page Wizard Step 1 Getting Started Wizard Step 2 Time Zone Configuration Wizard Step 3 ADSL Settings Wizard Step 4 Wireless Settings Wizard Step 3 Configuration Saving System Status Status LAN Status WLAN Status WAN Status Port Mapping Status Traffic Statistics Status DSL Statistics Status ARP Table WLAN Basic Settings Wireless Security Setup Advanced Settings Wireless Security Setup None Wireless Security Setu
94. n rate depending on line quality and loading to ensure data quality such as keeping within a maximum error rate 152 RJ 45 CONNECTOR SPLITTER SNTP TCP IP TIA UDP UPNP UTP VPN WAN GLOSSARY A connector for twisted pair wiring A filter to separate DSL signals from POTS signals to prevent mutual interference Simple Network Time Protocol SNTP allows a device to set its internal clock based on periodic updates from a Network Time Protocol NTP server Updates can be requested from a specific NTP server or can be received via broadcasts sent by NTP servers Transmission Control Protocol Internet Protocol Protocol suite that includes TCP as the primary transport protocol and IP as the network layer protocol Telecommunications Industry Association User Datagram Protocol UDP provides a datagram mode for packet Switched communications It uses IP as the underlying transport mechanism to provide access to IP like services UDP packets are delivered just like IP packets connection less datagrams that may be discarded before reaching their targets UDP is useful when TCP would be too complex too slow or just unnecessary Universal Plug and Play A set of protocols that allows devices to connect seamlessly and simplifies the deployment of home and office networks using auto discovery of other network devices acquiring information about device capabilities and requests for services Unshielded
95. nd Pinouts on page 147 for a description of cable types Note Make sure the twisted pair Ethernet cable connected to the router s Ethernet port does not exceed 100 meters 328 feet POWERING ON Plug the power adapter cord into the DC 12V power socket on the router and then plug the power adapter directly into a power outlet Check the LED marked Power on the top of the unit to be sure it is on If the Power indicator does not light up refer to Troubleshooting on page 141 If the router is properly configured it will take about 30 seconds to establish a connection with the ADSL service provider after powering up During this time the Link indicator will blink during synchronization After the ADSL connection has been established the Link indicator will stay on CONFIGURING THE TCP IP PROTOCOLS To connect the router to a computer through its Ethernet port the computer must have an Ethernet network adapter card installed and be configured for the TCP IP protocol Your service provider will configure TCP IP for client computers automatically using a networking technology known as Dynamic Host Configuration Protocol DHCP Carry out the following steps to check that the computer s Ethernet port is correctly configured for DHCP WINDOWS 95 98 NT 1 Click Start Settings Control Panel 2 Click the Network icon 3 For Windows NT click the Protocols tab 32 CHAPTER 2 Installing th
96. nd the acknowledge response gets sent to a maicious IP address or the system is flooded with false SYN requests 109 CHAPTER 8 Services DoS Whole System Flood FIN Prevents a FIN no more data from sender flood in which part of a TCP packet from an invalid or spoofed IP address floods the network with connection resets Whole System Flood UDP Prevents a flood of large numbers of raw UDP User Datagram Protocol packets targeted at the unit Whole System Flood ICMP Prevents a flood of ICMP internet control message protocol messages from an invalid IP address causing all TCP requests to be halted Per Source IP Flood SYN Prevents a SYN attach on a specified IP address usually that of the LAN port Per Source IP Flood FIN Prevents a FIN attach on the LAN port IP address Per Source IP Flood UDP Prevents a UDP attack on the LAN port IP address Per Source IP Flood ICMP Prevents an ICMP attack on the LAN port IP address TCP UDP Port Scan Prevents a situation whereby a hacker sends a series of systematic queries to the unit for open ports through which to route traffic TCMP Smurf Prevents a situation whereby a hacker forges the IP address of the unit and sends repeated ping requests to it flooding the network IP Land Prevents an attack that involves a synchronise request being sent as part of the TCP handshake to an open port specifying the port as both the source and destination effectively lockin
97. nection Displays the connectivity of the Ethernet LAN port ADSL CONNECTION TEST Displays the results of a test for connectivity on the WAN port Test ADSL Synchronization Displays the connectivity of the ADSL synchronisation Test ATM OAM F5 Segment Loopback Displays the connectivity of an F5 segment loopback of the permanent virtual circuit PVC connection with your service provider Test ATM OAM F5 End to end Loopback Displays the connectivity of an F5 end to end loopback integrity test of the permanent virtual circuit PVC connected to your service provider Test ATM OAM F4 Segment Loopback Displays the connectivity of an F4 segment loopback of the permanent virtual circuit PVC connection with your service provider Test ATM OAM F4 End to end Loopback Displays the connectivity of an F4 end to end loopback integrity test of the permanent virtual circuit PVC connected to your service provider 126 CHAPTER 10 Diagnostics Ping PING The ADSL Router provides the function of pinging its own IP address or URL to test for connectivity Figure 75 Ping Ping Diagnostic Host 182 168 2 9 The following items are displayed on this page Host The host IP address or URL to test for connectivity Run Ping Sends the ping request resulting in the the following page Figure 76 Ping Result Ping Diagnostic PING 192 168 2 9 1st 64 bytes from 192 1
98. nfiguration Figure 63 IGMP Proxy Configuration IGMP Proxy Configuration IGMP proxy enables the system to issue IGMP hast messages on behalf of hosts that the system discovered through standard IGMP interfaces The system acts as a proxy for its hosts when you enable it by doing the follows Enable IGMP proxy on WAN interface upstream which connects to a router running IGMP Enable IGMP on LAN interface downstream which connects to its hosts IGMP Proxy C Disable 9 Enable Multicast Allowed Disable Enable Robust Count Last Member Query Count Query Interval g seconds Query Response Interval 100m Group Leave Delay ms The following items are displayed on this pages IGMP Proxy Enables IGMP proxy When enabled the upstream interface acts as a host interface sending query messages periodically to the downstream interfaces sending join and leave messages to the upstream multicast router when a first join or last leave message is received from a downstream interface and sending membership reports in response to query messages from the multicast router Multicast Allowed Enables multicast forwarding Default Enabled Robustness Count Specifies the robustness or expected packet loss for interfaces The robustness value is used in calculating the appropriate range for other IGMP variables Range 1 255 Default 2 Last Member Query Count The numbe
99. ntrol List MAC Address Select The following items are displayed on this page Wireless Access Control Mode Enables disables ACLs on the ADSL Router Options are Disable Disables all ACLs Allow Listed Configures an allowed list of MAC addresses Those MAC addresses not in the allowed list will not be allowed to connect to the wireless interface Deny Listed Configures a denied list of MAC addresses The MAC addresses specified will not be allowed to connect to the wireless interface MAC Address The specified MAC address in the ACL Allowed or Denied list Select Selects a MAC address from the list Delete Selected Deletes a selected MAC address Delete All Deletes all entries from the ACL table 64 CHAPTER 5 WLAN Configuration Wi Fi Protected Setup WPS Wi Fi PROTECTED SETUP WPS Wi Fi Protected Setup WPS is designed to ease installation and activation of security features in wireless networks WPS has two basic modes of operation Push button Configuration PBC and Personal Identification Number PIN The WPS PIN setup is optional to the PBC setup and provides more security The WPS button on the router can be pressed at any time to allow a single device to easily join the network The WPS Settings page includes configuration options for setting WPS device PIN codes and activating the virtual WPS button Figure 28 WPS Configuration Wi Fi Protected Setup This pag
100. o other units 77 CHAPTER 6 LAN Settings DHCP Settings DHCP SERVER The unit can support up to 253 local clients Addresses are assigned to clients from a common address pool configured on the unit Configure an address pool by specifying start and end IP addresses Be sure not to include the unit s IP address in the address pool range Figure 38 DHCP Server DHCP Mode This page is used to configure DHCP mode You can set DHCP mode to None DHCP Relay or DHCP Server 1 Set the DHCP mode to DHCP Server if you are using this device as a DHCP server This page lists an IP address pool available to hosts on your LAN The device assigns IP addresses in the pool to hosts on your network when they request Internet access 2 Set the DHCP mode to DHCP Relay if you are using another DHCP server to assign IP address to your hosts on the LAN You can set the IP address of the DHCP server 3 If you set the DHCP mode to None the device does not assign IP addresses to the hosts when they request an IP address LAN IP Address 182 158 2 1 Subnet Mask 255 255 255 0 DHCP Mode DHCP Serer LAN LAN2 LAN3 LANA v WLAN vvAPO Interface MVAP1 MVAP2 v vAP3 IP Pool Range 192 168 2 2 192 168 2 254 Show Client Default Gateway 192 168 2 1 Max Lease Time 1440 minutes Domain Name domain com DNS Servers 192 158 2 1 Apply Changes Set VendorClass IP Range The following items are displayed on this
101. o LAN device ouppiopqouoverai TTDOO TIO EAAnvIKn OUOIWOEIO ATIAITNOEIO KAI TIO AOITTED oyeriKeo OIATAZEIO THO o rjyiao 1999 5 ek Hungarian Alulirott Manufacturer nyilatkozom hogy a Radio LAN device megfelel a vonatkoz Magyar alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Italian Con la presente Manufacturer dichiara che questo Radio LAN device conforme ai Italiano requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Latvian Ar o Manufacturer deklare ka Radio LAN device atbilst Direktivas 1999 5 EK b tiskajam Latviski prasibam un citiem ar to saistitajjem noteikumiem Lithuanian Siuo Manufacturer deklaruoja kad Sis Radio LAN device atitinka esminius reikalavimus ir Lietuviu kitas 1999 5 EB Direktyvos nuostatas Maltese Malti Polish Polski Portuguese Portugu s Romanian Romana Slovak Slovensky Slovenian Slovensko Spanish Espanol Swedish Svenska Turkish Turk COMPLIANCES Hawnhekk Manufacturer jiddikjara li dan Radio LAN device jikkonforma mal htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid Dirrettiva 1999 5 EC Niniejezym Manufacturer o wiadcza ze Radio LAN device jest zgodny z zasadniczymi wymogami oraz pozostalymi stosownymi postanowieniami Dyrektywy 1999 5 EC Manufacturer declara que este Radio LAN device est conforme com os requisitos essenciais e outras disposi es da Directiva 1999
102. om IP addresses in the ACL table are allow access to the ADSL Router When you select LAN for the ACL direction you can configure ACLs that apply to the LAN interfaces Figure 47 LAN ACL Configuration ACL Configuration You can specify which services are accessable form LAN or WAN side Entries in this ACL table are used to permit certain types of data packets from your local network or Internet network to the Gateway Using of such access control can be helpful in securing or restricting the Gateway managment Direction Select 2 LAN WAN LAN ACL Switch Enable Disable Apply Changes IP Address The IP 0 0 0 0 represent any IP Services Allowed Any v Web Telnet FTP CITFTP SNMP CIPING Current ACL Table Direction iP Addressfinterface_ Service Port Action The following items are displayed on this page LAN ACL Switch Enables LAN ACLs on the ADSL Router Default Disabled NorE Do not enable ACLs without first configuring your host IP address in the ACL table otherwise you will not be able to access the unit Apply Changes Implements the ACL settings on the ADSL Router IP Address Specify a LAN IP address or range of addresses that are allowed access to the ADSL Router Services Allowed Specifies services that are allowed access from LAN interfaces or allows any Add Adds the ACL to the ACL Table 92 CHAPTER 8 Se
103. omply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications This transmitter must not be co located or operating in conjunction with any other antenna or transmitter However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by
104. onnection MBS Maximum Burst Size Configures the maximum allowable burst size of cells that can be transmitted contiguously on a particular connection Current ATM VC Table The Current ATM VC Table lists the current ATM settings configured on your ADSL Router By selecting the connection using the radio button associated with it you can edit the connection parameters 85 ADSL SETTINGS CHAPTER 7 WAN Settings ADSL Settings The ADSL Settings page configures the ADSL modulation type ADSL2 related parameters capabilities and the ADSL tone mask Figure 43 ATM Settings ADSL Settings This page is used to configure ADSL settings of the device ADSL Modulation L1G Lite G Dmt T1413 ADSL2 ADSL2 AnnexL Option Enable AnnexM Option C Enable ADSL Capability Bitswap Enable SRA Enable Apply Changes The following items can be enabled on this page ADSL Modulation ADSL Modulation refers to a frequency division multiplexing FDM scheme utilized as a digital multi carrier modulation method for DSL A large number of closely spaced orthogonal sub carriers are used to carry data The data is divided into several parallel data streams or channels one for each sub carrier Each sub carrier is modulated with a conventional modulation scheme such as G lite ADSL2 etc or more commonly ADSL2 G lite A standard that defines the more economical splitterless ADSL connection that transmits dat
105. onnection to the management interface connect a PC to one of the router s LAN ports Set your PC with a static address within the same subnet as that used by the router that is 192 168 2 x with the subnet mask 255 255 255 0 To access the configuration menu follow these steps 1 Use your web browser to connect to the management interface using the default IP address of 192 168 2 1 Figure 5 Web Login ADSL Router Windows Internet Explorer OX Go X ntp 192 168 2 1 09n htm gt Being lel 4 Favorites ADSL Router A X 22 Page Safety Tools v e i SMC ADSL2 2 Barricade N iE Networks SMC7904WBRAS N2 v2 Login Screen Login ID Password Please enter correct password for administrator access Thank you We suggest that you use Internet Explorer 5 0 or above at a mininum 1024 X 768 resolution Copy Right 2012 SMC Networks Inc All right reserved 2 Login to the router s management interface using this account Login ID admin Password smcadmin 36 HOME PAGE CHAPTER 3 System Configuration Using the Web Interface NOTE It is strongly recommended to change the default password the first time you access the web interface For information on changing the password see Password Setup on page 135 When your web browser connects with the router s web agent the home page is displayed as shown below Basic inf
106. ormation can be viewed using the Status menu To carry out detailed configuration tasks use the other menu items Figure 6 Home Page SMC ADSL2 2 Barricade N Networks SMC7904WBRAS N2 v2 System Status This page shows the current status and some basic settings of the device System Alias Name SMC 9D4WBRAS N2 v2 ptime hh mm ss pod ay SMC7904WBRAS N2 v2 v1 0 0 0 WAN Interface DSL Operational Status Upstream Speed ho O Downstream Speed GENE The main menu is displayed on the left side of the screen Click on any of these items to open the sub menu list The information in this chapter is organized to reflect the structure of the web management screens for easy reference The configuration pages include the options listed in the table below For details on configuring each feature refer to the corresponding page number Table 2 Configuration Menu Menu Description Page Wizard Starts the setup wizard 40 Status System Shows hardware software version numbers DSL 45 connection status and Internet connection settings LAN Shows the LAN IP and DHCP server settings 46 WLAN Shows wireless interface settings 47 WAN Shows WAN interface functional status including 48 connection mode single or multiple service IGMP and connection status Port Mapping Shows the port mapping settings 49 Statistics OF s CHAPTER 3 System Configuration Using the Web Interface Table 2 Con
107. ors LED Power DSL Internet Status On Green On Red Off On Green Fast Blinking Green Slow Blinking Green On Green Blinking Green On Red Off 28 Description The router is being supplied with power E poner is running its self test or the self test has ailed The router is not receiving power The DSL Line port has a link with the service provider A DSL link is being established with the service provider No DSL signal detected The Internet connection is in its normal routing mode for example PPP dial up is successful but no data is being transmitted Internet data is being transmitted in routing mode The Internet connection has failed after successful synchronization in routing mode for example PPP dial up has failed The device is in bridge mode POWER CONNECTOR POWER BUTTON WLAN BUTTON WPS BUTTON RESET BUTTON CHAPTER 1 Introduction Description of Hardware Table 1 LED Display Indicators Continued LED Status Description LAN On Green Ethernet port has a valid link with attached device ud Blinking Green Data is being transmitted or received on the port Off Ethernet port has no link with an attached device WLAN On Green The Wi Fi radio is enabled Blinking Green Data is being transmitted through the WLAN interface Off The Wi Fi radio is disabled WPS On Green WPS is activated and the router is waiting for negotiation with wireless clients Off WPS is not
108. ot respond ina timely manner traffic will be dropped because the IP address cannot be mapped to a MAC address If this occurs you can use ARP Binding to manually map an IP address to the corresponding MAC address in the ARP cache Figure 65 ARP Binding Configuration ARP Binding Configuration This page lists the permanent arp entry table You can bind ip with corresponding mac to avoid arp spoof IP Address 0 0 0 0 Mac Address OOOOOUU00000 ex OOEO867 10502 ARP Binding Table _ Select MAC Address 192 168 2 33 00 11 22 33 44 55 The following items are displayed on this pages IP Address IP address statically mapped to a physical MAC address Valid IP addresses consist of four numbers O to 255 separated by periods and must match a known network interface MAC Address MAC address statically mapped to the corresponding IP address Valid MAC addresses are hexadecimal numbers in the format XXXXXXXXXXXX did ADVANCED The Advanced Configuration settings for the ADSL Router contain advanced system management configuration settings The following sections are contained in this chapter Bridge Setting on page 116 Log Setting on page 117 Routing Configuration on page 118 UPnP on page 120 SNMP Protocol Configuration on page 121 System Time Configuration on page 122 Other Advanced Configuration on page 123 Port Mapping on page 124 115 e BRI
109. oute Diagnostic Hast NumberOfTries Timeout S000 ms Datasize SEP H MaxHopCount Interface any traceroute The following items are displayed on this page Host The IP address of the destination host Number of Tries The number of datagrams to be sent at each TTL level The default count is 3 Range 1 10 Timeout The number of seconds to wait for a response to a probe packet The default is 5000 ms Range 1 65535 Datasize Number of bytes in the packet The default is 38 bytes Range 64 1518 DSCP The DSCP value in the IP Header of the packet Range 0 63 Max Hop Count The largest TTL value that can be used The traceroute terminates when the destination is reached or when this value is reached The default is 30 Range 1 255 Interface Selects the interface on which to run the traceroute 125 CHAPTER 10 Diagnostics Traceroute Figure 79 Traceroute Result Traceroute Diagnostic Traceroute 192 168 2 9 1 192 168 2 9 traceroute finished 129 CHAPTER 10 Diagnostics ADSL Tone Diagnostics ADSL TONE DIAGNOSTICS The ADSL page displays diagnostic testing for the ADSL connection Figure 80 ADSL Tone Diagnostics Diagnostic ADSL This page is used to diagnose the ADSL tone ee Downstream Upstream Hlin Scale Loop Attenuation dB Signal Attenuation dB SNR Margin dB Attainable Rate Kbp
110. p None Wireless Security Setup WEP Wireless Security Setup WEP Key Setup Wireless Security Setup WPA WPA2 Setup Wireless Security Setup Wireless Access Control WPS Configuration Second BSSID WDS Configuration WDS Wireless Setup zc oun 27 28 28 31 36 37 40 40 41 43 44 45 46 47 48 49 50 51 52 55 57 59 60 60 61 62 64 65 67 68 69 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 LAN Basic Setup Disabling DHCP LAN Configuration IPv6 LAN Configuration DHCP Disabled DHCP Relay DHCP Server Device IP Range Table DHCP Static IP Assignment WAN Configuration ATM Settings ATM Settings DNS Server Configuration IPv6 DNS Server Configuration DDNS DynDns LAN ACL Configuration WAN ACL Configuration IP Port Filtering Settings NAT Virtual Servers NAT Exclude IP NAT Forwarding Settings NAT ALG and Pass Through NAT Port Trigger NAT FTP ALG Configuration NAT IP Mapping Quality of Service MAC Filtering Settings DMZ Settings URL Blocking Settings Software Forbidden Settings DoS Settings IGMP
111. pecifies the IP addresses from the DHCP IP pool to assign to this device type Router Address Specifies a default router IP address to use for traffic from this device m Option 60 Specifies the DHCP Option 60 vendor class identifier that indicates the device type Figure 39 Device IP Range Table Device IP Range Table This page is used to configure the IP address range based on device type Device Mame Stat Address End Address IP Range Table Select Device Name Start Address End Address Default Gateway Option60 79 CHAPTER 6 LAN Settings DHCP Settings DHCP Static IP Assigns a physical MAC address to the DHCP pool by mapping it to a corresponding IP address Figure 40 DHCP Static IP Assignment DHCP Static IP Configuration This page lists the static IP address and MAC address on your LAM The device assigns the IP addresses to hosts on your network when they request Internet access IP Address 0 0 0 0 MAC Address OOOOOON00000 ex OOEO867 10502 Delete Selected DHCP Static IP Table Select IP Address MAC Address The following items are displayed on this page IP Address Enter the IP address from the DHCP address pool to assign to the specified MAC address MAC Address Enter the MAC address to be assigned to a static IP address from the DHCP address pool Add Selecting this option enters the mapped MAC address and IP address into the DHCP Sta
112. possible they will notify you in advance But if advance notice is not practical you will be notified as soon as possible You will be informed of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service If you experience trouble with this telephone equipment please contact please contact our company at the numbers shown on back of this manual for information on obtaining service or repairs The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs REN RINGER EQUIVALENT NUMBERS STATEMENT Notice The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 ATTACHMENT LIMITATIONS STATEMENT Notice This equipment meets telecommun
113. ps from router to router that the packets must make before reaching their final destination Interface Displays the interface the packets will be routed on 119 UPNP CHAPTER 9 Advanced UPnP UPnP Universal Plug and Play provides inter connectivity between devices Supported by the same standard UPnP is based on standard Internet protocols such as TCP IP UDP and HTTP Figure 69 UPnP UPnP Configuration This page is used to configure UPnP The system acts as a daemon when you enable UPnP UPnP Disable Enable WAN Interface E Apply Changes The following items are displayed on this page UPnP Enables UPnP on the ADSL Router Default Enabled WAN Interface Selects the WAN interface for the UPnP service 120 CHAPTER 9 Advanced SNMP Protocol Configuration SNMP PROTOCOL CONFIGURATION Simple Network Management Protocol SNMP is a communication protocol designed specifically for managing devices on a network SNMP is typically used to configure devices for proper operation in a network environment as well as to monitor them to evaluate performance or detect potential problems The ADSL Router can be managed locally or remotely by SNMP Figure 70 SNMP Configuration SNMP Protocol Configuration This page is used to configure the Simple Network Management Protocol SNMP In this page you can modify the settings of system description trap IP address and community name
114. psulated Traffic over ATM feature allows you to send bridged RFC 1483 encapsulated packets over ATM switched virtual circuits SVCs 1483 Routed Allows you to send routed RFC 1483 encapsulated packets over ATM switched virtual circuits SVCs IPoA Dynamic IP over ATM IPoA Connection Type Your connection type will also be specified by your service provider Choose from the following options VC Mux Virtual circuit multiplexing VC Mux m LLC Logical Link Control LLC VPI The ATM Virtual Path Identifier Range 0 255 VCI The ATM Virtual Channel Identifier Range 32 65535 Username Enter the username provided by your service provider Password Enter the password provided by your service provider Confirm Password Re enter your password 42 CHAPTER 3 System Configuration Setup Wizard STEP 4 WIRELESS The fourth page of the wizard configures wireless settings for the ADSL SETTINGS router Figure 10 Wizard Step 4 Wireless Settings 4 Wireless Settings This page allows you to configure the wireless SSID Mode and channel Optionally you can disable broadcasting of SSID for added security SSID is the name given to your wireless LAN Wireless clients should be configured to use the same SSID a Enter new SSID or use the default value b Select Wireless mode For best compatibility SMC recommend Mixed 11b 11g 1in c Select operating channel d Select Enc
115. r of query messages sent before the router determines that there are no remaining members of the specific host group being queried on the interface Range 1 255 Default 2 Query Interval The interval between sending IGMP general queries Range 2 31744 seconds Default 60 seconds Query Response Interval The maximum time the system waits for a response to general queries Range 10 31744 tenths of a second Default 10 seconds Group Leave Delay The time duration it takes a device to stop forwarding multicast frames after an IGMP Leave Group message has been successfully sent to the device Default 2000 ms 112 CHAPTER 8 Services RIP Configuration RIP CONFIGURATION RIP is an Internet protocol you can set up to share routing table information with other routing devices on your LAN at your ISP s location or on remote networks connected to your network via the ADSL line Most small home or office networks do not need to use RIP they have only one router such as the router and one path to an ISP In these cases there is no need to share routes because all Internet data from the network is sent to the same ISP gateway Figure 64 RIP Configuration RIP Configuration Enable the RIP if you are using this device as a RIP enabled router ta communicate with others using the Routing Information Protocol Disable Enable Apply Changes Interface Receive Version Send Version RIP Configura
116. rameters System 1970 year Jan month 1 day B hours min 20 Time sec DayLight LocalTIME v NTP Configuration State Primary Server Secondary Server Disable C Enable Interval Every 1 hours Time Zone Local Time GMT Gambia Liberia Morocco England Thu Jan 1 6 5 20 1970 NTP Start Get GMT Time The following items are displayed on this page System Time Displays the current date and time and allows you to manually configure time settings DayLight Enables daylight saving time to be configured State Enables NTP Network Time Protocol Default Disabled Primary Secondary Server Specifies NTP servers to poll for time updates Interval Specifies the interval to poll for time updates Time Zone Allows you to select your current location or nearest city All time zones are given in Greenwich Mean Time GMT Local Time Displays the current date and time and allows you to manually configure time settings NTP Start Initiates a time update from an NTP server 122 CHAPTER 9 Advanced Other Advanced Configuration OTHER ADVANCED CONFIGURATION Enables the Half Bridge feature for PPPoE PPPoA connections When the router is set to Half Bridge it establishes the PPPoE PPPoA connection with the ISP then forwards all other traffic to DHCP clients connected to the router Figure 72 Other Advanced Configuration Other Advance
117. ribes the WEP key setup Figure 25 Wireless Security Setup WEP Key Setup Wireless WEP Key Setup This page is used to configure the WEP key value You can select 64 bit or 125 bit as the encryption key and ASCII or Hex as the format of input value SSID Type Rot OVAPD OVAPI OVAP2 OVAP3 Key Length b4 hit w Key Format ASCI 5 characters Default Tx Key Key 1 w Encryption Key 1 ee Encryption Key 2 pee Encryption Key 3 T Encryption Key 4 ua The following items are displayed on this page SSID Type Selects the VAP to configure the WEP security settings to 61 CHAPTER 5 WLAN Configuration Wireless Security Setup Authentication Type Selects the authentication type to use Options are Open System If you don t set up any other security mechanism on the access point the network has no protection and is open to all users This is the default setting Shared Key Sets the access point to use WEP shared keys If this option is selected you must configure at least one key on the access point and all clients Auto Automatically selects the best authentication type to use Key Length Selects between 64 bit and 128 bit keys Key Format Selects the preferred method of entering WEP encryption keys on the unit m Alphanumeric Enter keys as 5 alphanumeric characters for 64 bit keys 13 alphanumeric characters for 128 bit keys This is the
118. roup Management Protocol IGMP multicast filtering 73 CHAPTER 6 LAN Settings IPv6 LAN Configuration LAN Port Selects the LAN port Link Speed Duplex Mode Selects the port speed and duplex mode or sets the port for auto negotiation MAC Address Control Filters out traffic with source MAC addresses not configured in the table For devices that need Internet access through the LAN port enter the MAC address and click Add IPv6 LAN CONFIGURATION This section describes how to configure an initial IPv6 interface for management access over the network or for creating an interface to multiple subnets This router supports both IPv4 and IPv6 and can be managed through either of these address types IPv6 includes two distinct address types link local unicast and global unicast A link local address makes the router accessible over IPv6 for all devices attached to the same local subnet However to connect to a larger network with multiple segments the router must be configured with a global unicast address Figure 35 IPv6 LAN Configuration LAN IPv6 Setting This page is used to configurate IPv6 LAN setting User can set LAN RA Router Advertisement server work mode and lan DHCPv6 server work mode RA Setting Enable M Flag O Flag Max Interval 60 Min Interval 20 Prefix Mode Manual Prefix Address Prefix Length 64 15 64 Preferred Time 4294967295 600 4294967295 S Vali
119. rvices Access Control Lists CURRENT ACL TABLE Lists the configured ACLs on the LAN ports Select The number of the entry in the table Direction Displays if the ACL is applied to a LAN or WAN interface IP Address Interface Displays the allowed IP address or range Service Dispays the allowed service Port Displays the TCP UDP port of the allowed service 9 6M Action Click the button to remove the entry from the table WAN ACLS When you select WAN for the ACL direction you can configure ACLs that apply to WAN interfaces Figure 48 WAN ACL Configuration ACL Configuration You can specify which services are accessable form LAN or VVAN side Entries in this ACL table are used to permit certain types of data packets from your local network or Internet network to the Gateway Using of such access control can be helpful in securing or restricting the Gateway managment Direction Select LAN WAN WAN Setting Interface WAN Interface any Services Allowed Web v Telnet Port 23 CIFTP CITFTP SNMP Port 151 PING Current ACL Table _ Select Direction _IPAddressfnterface_ Service Port Action The following items are displayed on this page WAN Setting Selects a WAN interface or IP address WAN Interface Specifies a configured WAN interface for the ACL IP Address Specify a LAN IP address or range of addresses that are allowed acc
120. ry 3 or better UTP cable IEEE 802 3 2005 specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable IEEE 802 3ab specification for 1000 Mbps Gigabit Ethernet over four pairs of Category 5 or better UTP cable The core infrastructure of a network The portion of the network that transports information from one central location to another central location where it is unloaded onto a local system Dynamic Host Configuration Protocol Provides a framework for passing configuration information to hosts on a TCP IP network DHCP is based on the Bootstrap Protocol BOOTP adding the capability of automatic allocation of reusable network addresses and additional configuration options A popular local area data communications network which accepts transmission from computers and terminals A firewall is designed to prevent unauthorized access to or from a private network File Transfer Protocol A TCP IP protocol used for file transfer Hypertext Transfer Protocol HTTP is a standard used to transmit and receive all data over the World Wide Web Internet Service Provider A company that provides access to the Internet This may be your local telephone company or a dedicated Internet service company i151 ITU ITU T LAN MAC ADDRESS MTU NTP PING POTS PPP PPPoE PSTN Qos RATE ADAPTIVE GLOSSARY International Telecommunication Union Telecommunication Standardi
121. ryption e Click Next to continue WLAN Interface Enable Disable Band 24 GHz B G N v SSID SMC Encryption None v The following items are displayed on the first page of the Wizard WLAN Interface Enables disables the wireless 802 11b g n interface Band Selects the operating band and mode The router supports the 2 4 GHz band and can operate in any combination of 802 11b g or n modes SSID Specifies an SSID service set identifier which must be the same as that on all wireless clients that wish to associate with the unit Encryption Specifies the security used to protect your wireless network Default None None Allows any wireless client within range to associate with the ADSL Router WEP Provides a basic level of security using static shared keys that are distributed to all clients Be sure to configure at least one static key Alternatively enable 802 1X authentication to dynamically create and distribute keys from a RADIUS server WPA TKIP AES Wi Fi Protected Access WPA using either a static pre shared key or 802 1X authentication through a RADIUS server The encryption used is either TKIP or AES 43 CHAPTER 3 System Configuration Setup Wizard WPA2 TKIP AES WPA2 using either a static pre shared key or 802 1X authentication through a RADIUS server The encryption used is either TKIP or AES WPA2 Mixed WPA and WPA2 using eith
122. s Indicates if the group mapping is enabled d0 CHAPTER 4 Device Information Traffic Statistics TRAFFIC STATISTICS The ADSL Router Traffic Statistics Interfaces window displays received and transmitted packet statistics for all interfaces on the ADSL Router Figure 17 Status Traffic Statistics Traffic Statistics This page shows the packet statistics for transmission and reception regarding to network interface Interface Ru Packet Ru Error Rx Drop Tx Packet Tx Error TX Drop et 600 0 o j m 0 0 The following items are displayed on this page Interface Displays the interface on which traffic is being monitored Rx Packet Displays the total number of packets received by the specified interface RxError Displays the total number of packet errors received by the specified interface if any Rx Drop Displays the total number of received packets dropped by the specified interface Tx Packet Displays the total number of packets transmitted by the specifed interface Tx Error Displays the total number of packet errors occured during transmission by the specified interface Tx Drop Displays the total number of packets transmitted but dropped by the specified interface Refresh Updates the statistical table for all interfaces 50 CHAPTER 4 Device Information DSL Statistics DSL STATISTICS The ADSL Router DSL Statistics window displays re
123. s Output Power dBm Tone Number _H Real__ Himage SNR QLN RENI 0 The following items are displayed on this page Start Starts the diagnostics test Downstream Upstream Displays downstream and upstream traffic Hlin Scale Displays the scaling factor for H Real and H Image represented in fixed point format Loop Attenuation dB Displays the attentuation of the link to the ADSL Router and the service provider in decibels Signal Attenuation dB Displays the signal attentuation of the link which determines the frequency in decibels SNR Margin dB Displays the signal to noise ratio of the link in dedibels Attainable Rate Kbps Displays the attainable rate of the link to the service provider in kilobits per second Lav CHAPTER 10 Diagnostics ADSL Tone Diagnostics Output Power dBm Displays the output power of the unit in decibels per milliwatt Tone Number Displays the tone number of the ADSL signal Range 0 255 H Real Displays the real part of channel transfer function of each subcarrier H Image Displays the imaginary part of channel transfer function of each subcarrier SNR Displays the SNR Singal to Noise Ratio of each subcarrier expressed in decibels QLN Displays the Quite Line Noise of each subcarrier expressed in dBm HZ Hlog Displays the amplitude response of channel transfer function of each subcarrier e
124. s A predefined list of countries amp Internet Service Providers ISP is available for easy configuration a Select Country b Select ISP Note If Country or ISP is not listed select Other You will be required to manually select the Protocol amp fill in blank fields For correct values contact your ISP c Enter required values d Click Next to continue Click to Select v Click to Select v Country Internet Service Provider Protocol Connection Type YPI VCI The following items are displayed on the first page of the Wizard Country Choose your country of operation from the drop down menu If your country is not listed contact your service provider for detailed settings Internet Service Provider The chosen country will determine the list of available Internet Service Providers Choose the service provider with which you have a contract Protocol The protocol used will be specified by your service provider Choose from the following options PPPoE Point to Point Protocol over Ethernet PPPoE PPPoA Point to Point Protocol over Asynchronous Transfer Mode PPPOA 41 9 CHAPTER 3 System Configuration Setup Wizard 2 1483 MER DHCP 1483 MER is an RFC standard MAC Encapsulated Routing protocol 1483 MER Static IP 1483 MER is an RFC standard MAC Encapsulated Routing protocol 1483 Bridged The Bridged RFC 1483 Enca
125. se of such filters can be helpful in securing or restricting your local network Outgoing Default Policy Deny Allow Incoming Default Policy Deny Allow Direction Outgoing Action Deny O Allow Source MAC Address ex 00E086710502 Destination MAC Address ex OOE086710502 Add Current MAC Filter Table Select Direction Source MAC Address Destination MAC Address Action Delete All The following items are displayed on this page Outgoing Default Policy A default action for MAC addresses not configured in the filter table Default Allow maximum 32 entries are allowed Incoming Default Policy A default action for MAC addresses not configured in the filter table Default Allow maximum 32 entries NorE The default outgoing and incoming defaults allow traffic from all MAC addresses Direction Specifies the packet destination Default Outgoing Action Specifies if traffic should be permitted or denied Options Deny Allow Default Deny Source MAC Address Specifies a source MAC address Destination MAC Address Specifies a destination MAC address 105 DMZ CHAPTER 8 Services DMZ DMZ enables a specified host PC on the local network to access the Internet without any firewall protection Some Internet applications such as interactive games or videoconferencing may not function properly behind the router s firewall By specifying
126. server IPv6 addresses Attain DNS Automatically C Set DNS Manually DNS 1 Interface DNS 2 Interface DNS 3 Interface 89 CHAPTER 8 Services DNS Settings The following items are displayed on this page Obtain DNS Automatically The DNS server IPv6 address is automatically configured during dynamic IP assignment Set DNS Manually Allows the user to set up to three DNS server IPv6 addresses DDNS Dynamic DNS DDNS provides users on the Internet with a method to tie a specific domain name to the unit s dynamically assigned IP address DDNS allows your domain name to follow your IP address automatically by changing your DNS records when your IP address changes The ADSL Router provides access to two DDNS service providers DynDns org and TZO To set up an DDNS account visit the websites of these service providers at www dyndns org or www tzo com Figure 46 DDNS DynDns Dynamic DNS Configuration This page is used to configure the Dynamic DNS address from DynDNS org or TZO Here you can Add Remove to configure Dynamic DNS DDNS provider DynDNS org v Host Name Interface Enable DynDns Settings User Name Password TZO Settings Email Key Dynamic DDNS Table Select State Service HostName UserName NN The following items are displayed on these pages DDNS provider Specify the DDNS provider from th
127. server of ADSL Router Empty user name or password is not allowed User Name Privilege User vw Old Password New Password Confirm Password User Account Table Select UserName Privilege admin root user user The following items are displayed on this page User Name Specifies the user name to configure Privilege Configures the access privileges that the user has Select between Admin Grants administrator level access no restrictions User Grants user level access some configuration restrictions Old Password The password for management access The default passwords preset for access to the unit is smcadmin for admin and user level Length 3 16 characters case sensitive New Password Enter a new password Confirmed Password Enter the new password again for verification io UPGRADE FIRMWARE CHAPTER 11 Administration Settings Upgrade Firmware You can update the ADSL Router s firmware by using the Upgrade Firmware facility which allows you to upload new firmware manually by specifying a file path Make sure the firmware file you want to use is on the local computer by clicking Browse to search for the file to be used for the update Figure 85 Upgrade Firmware Upgrade Firmware This page is used to upgrade the firmware to a new version system will reboot after the file is uploaded Caution
128. t customers try to avoid using multiple circuits because it adds unnecessary cost Channel Mode The protocol used on the channel as specified by the service provider Choose from the following options 1483 Bridged The Bridged RFC 1483 Encapsulated Traffic over ATM feature allows you to send bridged RFC 1483 encapsulated packets over ATM switched virtual circuits SVCs 1483 MER 1483 MER is an RFC standard MAC Encapsulated Routing protocol PPPoE Point to Point Protocol over Ethernet PPPoE PPPoA Point to Point Protocol over Asynchronous Transfer Mode PPPOA 1483 Routed Allows you to send routed RFC 1483 encapsulated packets over ATM switched virtual circuits SVCs IPoA Dynamic IP over ATM IPoA Enabled NAPT Enables Network Address Port Translation for the channel Enable IGMP Enables IGMP for the channel PPP Settings Configures settings for PPPoE and PPPoA modes User Name The PPP access user name provided by the ISP Password The PPP access password provided by the ISP Type Selects the connection type Continuous Connect on Demand or Manual Idle Time The number of minutes you want to have elapsed before your Internet access disconnects in Connect on Demand mode WAN IP Settings Configures settings for 1483 MER 1483 Routed and IPoA modes Type Selects fixed IP or DHCP When fixed IP is selected enter the local IP address gat
129. t primordial de laisser suffisamment d espace autour de l appareil pour permettre la dissipation de la chaleur et viter les d g ts provoqu s par une surchauffe de l appareil Les orifices de ventilation de l appareil sont concus pour permettre la dissipation thermique et garantir le bon fonctionnement de l appareil Ne couvrez jamais ces orifices Ne placez pas cet appareil proximit d une source de chaleur ou dans un endroit expos des temp ratures lev es Evitez galement de l exposer la lumi re directe du soleil Ne placez pas cet appareil proximit d un lieu humide ou mouill Prenez garde ne renverser aucun liquide sur cet appareil Merci de suivre les instructions du manuel d utilisateur guide d installation rapide attentivement pour connecter l appareil votre PC ou tout autre produit lectronique Toute connexion non valide peut provoquer un probl me lectrique ou un risque d incendie Ne placez pas cet appareil sur une surface ou un support instable SICHERHEITSMABNAHMEN Lesen Sie vor der Inbetriebnahme des Ger tes aufmerksam die nachstehenden Informationen Bitte befolgen Sie die nachstehenden SicherheitsmaBnahmen damit das Gerat nicht beschadigt wird oder Gefahren durch Brand oder elektrische Energie entstehen Verwenden Sie nur das beim Gerat mitgelieferte Netzteil Achten Sie auf die Last der Steckdose oder des Verlangerungskabels Eine berlastete Steckdose oder besc
130. tem log table Old New Displays the previous or next page of log entries dq CHAPTER 9 Advanced Routing Configuration EVENT LOG TABLE Displays the current entries in the System Log table Time Displays the date and time the log entry was created Index The number of the log entry Type Displays the source of the log message Log Information Information that identifies the cause of the event that prompted the system log message ROUTING CONFIGURATION This page displays the information necessary to forward a packet along the best path toward its destination Each packet contains information about its origin and destination When a packet is received a network device examines the packet and matches it to the routing table entry providing the best match for its destination The table then provides the device with instructions for sending the packet to the next hop on its route across the network Figure 68 Routing Configuration Routing Configuration This page is used to configure the routing information Here you can add delete IP routes Enable Destination Subnet Mask Next Hop Metric 1 Interface v Add Route Delete Selected Static Route Table Select State Destination Subnet Mask NextHop Metric Interface NE The following items are displayed on this page Enable Enables static routing on the ADSL Router Default Enabled
131. teway WAN IPV6 Configuration Interface VPINCI Encap Protocol IPv6 Address Gateway Droute IPv6 DNS Servers The following items are displayed on this page 9 Interface Displays the interface identifier VPI VCI Displays the ATM channel identifiers Encapsulation Displays the encapsulation type chosen either LLC to VX Mux Default Route Dipslays if a default route has been enabled Protocol Displays the protocol used for transmission of data packets IP Address Displays the local IP address of the WAN port Default Gateway Displays the network route or gateway used by the unit when no other known route exists for a given IP packet s destination address Status Specifies the status of the interface DNS Servers Specifies the IP addresses of DNS servers Ei PORT MAPPING CHAPTER 4 Device Information Port Mapping The Port Mapping status shows the mapping of WAN and LAN interfaces to specific groups Figure 16 Status Port Mapping Port Mapping This page shows the mapping relation and the status of port mapping Status Disabled Mapping Relation Select Interfaces Status Gmupl 000 0 0 doo The following items are displayed on this page Status Indicates if port mapping is enabled or disabled Select Indicates the group identification Interfaces Specifies the WAN and LAN interfaces in the group Statu
132. th an information flood that renders it Slow or effectively inoperable for genuine users to access it DoS attacks are also referred to as non intrusion attacks the goal of which is to cripple your system but not steal data The DoS Settings on the router enable the user to block many of the common DoS attacks a network might suffer Figure 62 DoS Settings Anti DoS Setting A denial of service DoS attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service Enable DoS Prevention Whole System Flood SYN 100 Packets Second Whole System Flood FIN 100 Packets Second Whole System Flood UDP 100 Packets Second Whole System Flood ICMP 100 Packets Second Per Source IP Flood SYN 100 Packets Second Per Source IP Flood FIN 400 Packets Second C Per Source IP Flood UDP 100 Packets Second C Per Source IP Flood ICMP 400 Packets Second TCP UDP PortScan Low Sensitivity ICMP Smurf IP Land IP Spoof IP TearDrop PingOfDeath TCP Scan TCP SynWithData UDP Bomb UDP EchoChargen C Enable Source IP Blocking 300 Block time sec Apply Changes The following items are displayed on this page Enable DoS Blocking Activates the DoS check boxes and configurable parameters associated with them Default Disabled Whole System Flood SYN Prevents a SYN synchronise attack in which the process of the common three way TCP handshake is interupted a
133. the party responsible for compliance could void the user s authority to operate this equipment FCC RADIATION EXPOSURE STATEMENT This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body FCC PART 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the bottom of this equipment is a label that contains among other information a product identifier in the COMPLIANCES format US 1KRDLO9BSMC7800A If requested this number must be provided to the telephone company This equipment uses the following USOC jacks RJ 11 The REN is useful to determine the quantity of devices you may connect to your telephone line and still have those entire devices ring when your telephone number is called In most but not all areas the sum of the REN of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to you line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If your equipment causes harm to the telephone network the telephone company may discontinue your service temporarily If
134. then an address must be manually configured using the fields described below Prefix Address The IPv6 address prefix sent in router advertisements Prefix Length The length of the IPv6 address prefix sent in router advertisements For IPv6 unicast addresses this is set to 64 Preferred Time The time over which the configured address is preferred Valid Time The time over which the configured address is valid DHCPv6 SETTING DHCPv6 Mode The DHCPv6 mode setting None DHCPvo is disabled Manual If auto configuration is not selected then an IPv6 address pool must be manually configured Auto Enables automatic assignment of IPv6 addresses on the router The network portion of the address is based on prefixes received in IPv6 router advertisement messages and the host 75 CHAPTER 6 LAN Settings DHCP Settings portion is automatically generated using the modified EUI 64 form of the client identifier that is the client MAC address IPv6 Address Pool The address range available for DHCPv6 assignment Prefix Length The length of the IPv6 address prefix sent in DHCPv6 assignments For IPv6 unicast addresses this is set to 64 Preferred Time The time over which assigned addresses are preferred Valid Time The time over which the assigned addresses are valid DNS Servers Specifies up to three IPv6 Domain Name servers for IPv6 addresses DH
135. tic IP Table Delete Selected Once you select and entry in the table by clicking its corresponding radio button this option deletes the entry Reset Clears the IP and MAC address fields 80 WAN SETTINGS This chapter describes WAN configuration on the ADSL Router The WAN pages are used to configure standard WAN services including VPI VCI encapsulation service type PPPoE IPoE bridging ATM settings and ADSL settings It includes the following sections Channel Configuration on page 82 ATM Settings on page 84 ADSL Settings on page 86 Ot CHAPTER 7 WAN Settings Channel Configuration CHANNEL CONFIGURATION The Channel Configuration page configures channel operation modes of the ADSL Router Figure 41 WAN Configuration Channel Configuration The DSL WAN connection can be separated virtually into multiple channels by assigning different VPIAYCI in each Permanent Virtual Circuit PVC In each PVC you can also set the connection protocol to be PPP Dynamic IP Static IP or Bridge mode Default Route Selection Auto Specified VPI VCI Encapsulation 9 LLC CO vVC Mux Channel Mode 1483 Bridged v Enable NAPT Enable IGMP PPP Settings User Name Password Type Idle Time min WAN IP Settings Type Fixed IP DHCP Local IP Address Gateway Netmask Default Route Disable Enable Unnumbered
136. ting ADSL Router and network problems The Log Setting page displays the latest messages logged in chronological order Log messages saved in the ADSL Router s memory are erased when the device is rebooted Figure 67 Log Setting Log Setting This page is used to show the system event log You can set the log flag to Error or Notice or both Click gt gt and the table shows the latest log information Error Notice Event Log Table otd i gt gt I New Index Thu Jan 1 0 0 0 1970 0 system Generic driver is up and running Thu Jan 1 0 0 0 1970 1 system DNS task is UP Thu Jan 10 0 2 1970 2 system Port 1 link up Thu Jan 1 0 1 43 1970 3 other admin web login successfully Thu Jan 1 0 18 59 1970 4 other admin web login successfully Thu Jan 1 1 53 4 1970 5 other admin web login successfully Thu Jan 1 2 1 11 1970 6 other admin web login successfully Thu Jan 1 3 40 38 1970 7 other admin web login successfully Thu Jan 1 4 4 23 1970 8 other admin web login successfully Thu Jan 1 4 53 50 1970 9 other admin web login successfully Thu Jan 15 33 41 1970 10 other admin web login successfully Page 1 1 The following items are displayed on this page Error Selects the Error level of messages to be displayed by the ADSL Router Notice Selects the Notice level of messages to be displayed by the ADSL Router Save Log to File Saves the currently recorded system logs to file Clear Log Table Clears the sys
137. tion List Select interface _ Receive Version Send Version LJ bro RIP 1 RIP 1 The following items are displayed on this pages RIP Enables or disables RIP on the unit Default Disabled Interface The name of the interface on which you want to enable RIP Default brO Receive Version Indicate the RIP version in which information must be passed to the DSL device in order for it to be accepted into its routing table Send Version Indicate the RIP version this interface will use when it sends its route information to other devices 115 CHAPTER 8 Services ARP Binding Configuration ARP BINDING CONFIGURATION The router uses its tables to make routing decisions and uses Address Resolution Protocol ARP to forward traffic from one hop to the next ARP is used to map an IP address to a physical layer MAC address When an IP frame is received by the router it first looks up the MAC address corresponding to the destination IP address in the ARP cache If the address is found the router writes the MAC address into the appropriate field in the frame header and forwards the frame on to the next hop IP traffic passes along the path to its final destination in this way with each routing device mapping the destination IP address to the MAC address of the next hop toward the recipient until the packet is delivered to its final destination For devices that do not respond to ARP requests or do n
138. to be uniquely identified on the network Uptime The length of time in minutes that the unit has been powered on Software Version The current version of firmware running on the unit DSP Version The current hardware version of the digital signal processor DSP DSL Operational Status Displays the status of the DSL connection mo E ux LAN STATUS CHAPTER 4 Device Information LAN Status Upstream Speed The current upload speed of the DSL connection Downstream Speed The current download speed of the DSL connection The ADSL Router LAN window displays basic LAN port settings including DHCP information Figure 13 Status LAN LAN Status This page shows basic LAN settings of the device LAN Configuration IP Address 192 158 2 1 Subnet Mask 255 255 255 0 DHCP Server MAC Address 00 1F 44 90 7 F 3E DHCP Client Table Name IP Address MAC Address The following items are displayed on this page LAN STATUS Displays the basic information of the LAN port IP Address Displays an IP address for local area connection to the ADSL Router Subnet Mask Displays the local subnet mask DHCP Server Displays whether the DHCP server has been enabled or not MAC Address Displays the physical layer address of the LAN port DHCP CLiENT TABLE Displays information on the DHCP configuration and lease time Name Displays the name of the client device IP Address
139. ts on page 92 IP Port Filtering on page 95 NAT NAPT Settings on page 97 Quality of Service on page 103 MAC Filtering on page 105 DMZ on page 106 URL Blocking on page 107 Software Forbidden on page 108 DoS on page 109 IGMP Proxy Configuration on page 111 RIP Configuration on page 113 ARP Binding Configuration on page 114 88 DNS SETTINGS DNS SERVER IPv6 DNS CHAPTER 8 Services DNS Settings Sets Domain Name Server DNS and Dynamic DNS settings The Domain Name Server DNS implements a human recognizable web address to a numerical IP address DNS can be set automatically or manually Figure 44 DNS Server Configuration DNS Configuration This page is used to configure the IP addresses of the DNS server in the DNS relay mode Obtain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 The following items are displayed on this page Obtain DNS Automatically The DNS server IP address is automatically configured during dynamic IP assignment Set DNS Manually Allows the user to set up to three DNS server IP addresses The IPv6 Domain Name Server DNS implements a human recognizable web address to a numerical IPv6 address DNS can be set automatically or manually Figure 45 IPv6 DNS Server Configuration IPv6 DNS Configuration This page is used to configure the DNS
140. uthenticate with the ACS server Click the Browse button to locate the file on your local PC and upload it to the unit using the Upload button CA Certificate The digital security certificate issued by a Certified Authority to be used by the unit when authenticating the ACS server Click the Browse button to locate the file on your local PC and upload it to the unit using the Upload button 139 SECTION Bil APPENDICES This section provides additional information and includes these items Troubleshooting on page 141 Hardware Specifications on page 143 Cables and Pinouts on page 147 140 DIAGNOSING GATEWAY INDICATORS Gateway operation is easily monitored via the LED indicators to identify problems The table below describes common problems you may encounter and possible solutions If the solutions in the table fail to resolve the problem contact technical support for advice Table 3 LED Troubleshooting Chart Symptom Power indicator does not light up after power on Ethernet link indicator does not light up after making a connection Link indicator is off or does not stop blinking i e synchronizing after making a connection Cause Power outlet power cord or external power adapter may be defective Network interface e g a network adapter card in the attached computer network cable or router LAN port may be defective Cabling or router
141. v Mode AP WDS SSID SMC Channel Width Control Sideband Channel Number Radio Power Percent Associated Clients A0MHZ vw Current Channel 11 Show Active Clients Apply Changes The following items are displayed on this page Disable Wireless LAN Interface Disables the Wireless LAN interface Default Enabled Band Defines the radio mode Default 2 4Ghz B G Mode The unit can function as an access point alone allowing connection to wireless clients or both access point and WDS wireless distribution system allowing WDS transparent bridging between APs Default AP WDS SSID The service set identifyer for the access point Default SMC Channel Width The router provides a channel bandwidth of 40 MHz by default giving an 802 11g connection speed of 108 Mbps sometimes referred to as Turbo Mode and a 802 11n connection speed of up to 150 Mbps Setting the HT Channel Bandwidth to 20 MHz slows connection speed for 802 11g and 802 11n to 54 Mbps and 74 55 CHAPTER 5 WLAN Configuration WLAN Basic Settings Mbps respectively and ensures backward compliance for slower 802 11b devices Default 40MHz Control Sideband Specifies if the extension channel should be in the Upper or Lower sideband When a 40MHz channel bandwidth has been set the extension channel option will be enabled in the upper or lower
142. way Router and describes how to install and mount the unit This section includes these chapters Introduction on page 26 Installing the Router on page 30 5 INTRODUCTION The Barricade ADSL Gateway Router SMC7904WBRAS N2 v2 is an ADSL2 2 modem contained in a compact unit The router enables multiple wired and wireless users to securely access the Internet through a single user account with the ADSL service provider The router provides four 10 100 Mbps Ethernet ports for connection to end users an IEEE 802 11b g n wireless interface and one ADSL line for connection to the Internet service provider FEATURES AND BENEFITS The features of the ADSL Gateway Router include e Full rate ADSL router support for Router and Bridge modes ITU G 992 3 ADSL2 and ITU G 992 5 ADSL2 ITU G 992 1 G dmt Annex A and ITU G 992 2 G lite ANSI T1 413 Issue 2 Provides 24 Mbps downstream and 1 Mbps upstream Maximum transmission range 5 4 Kilometers Four Ethernet ports 10 100 Mbps Auto MDI MDIX 802 11n 2 4 GHz radio supporting four SSID interfaces Friendly web based user interface for configuration Configurable as a DHCP server on your network Compatible with all standard Internet applications Industry standard and interoperable DSL interface Simple web based status page displays a snapshot of your configuration and links to the configuration pages Downloadable flash softwar
143. xpressed in decibels 131 ADMINISTRATION SETTINGS The Admin pages are used to manage configuration files system logs TR 069 ACS passwords and also to update software and reboot the system This chapter contains the following sections 9 9 Commit Reboot on page 133 Backup Restore Settings on page 134 Password Setup on page 135 Upgrade Firmware on page 136 TR 069 Configuration on page 137 Loe CHAPTER 11 Administration Settings Commit Reboot CoMMIT REBOOT Use this page to save the current configuration and reboot the system Figure 81 Commit Reboot Commit Reboot This page is used to save the current configuration or restore to the factory default configuration Reboot from save the current configuration The following items are displayed on this page Reboot from Select the option for router s configuration Save the current configuration Select this option if you want to save your changes for the next reboot Restore to the factory default configuration Select this option if you want to return all changes to default values Commit Changes Sets the selected configuration option Reset Resets the selected option on the page Reboot Restarts the router When rebooting the system the following page displays and a countdown from 64 seconds begins Figure 82 Rebooting Reboot System You click Reboot button the system
144. zation Section of ITU Local Area Network A group of interconnected computers and support devices The physical layer address used to uniquely identify network nodes Maximum Transfer Unit The maximum transfer unit for traffic crossing this device MTU should be set to a value that minimizes unnecessary fragmentation and maximizes the transfer of large sequential data streams Network Time Protocol NTP provides the mechanisms to synchronize time across the network The time servers operate in a hierarchical master Slave configuration in order to synchronize local clocks within the subnet and to national time standards via wire or radio A utility used to determine whether a specific IP address is accessible It works by sending a packet to the specified address and waiting for a reply Plain Old Telephone Service One of the services using voice band Sometimes used as a descriptor for all voice band services Point to Point Protocol A protocol for connecting remote hosts to the Internet using TCP IP PPP over Ethernet A protocol for connecting remote hosts to the Internet over an always on connection by simulating a dial up connection Public Switched Telephone Network Quality of Service A network protocol used to specify a guaranteed throughput level This protocol is often used by Internet service providers to guarantee their customers a minimum end to end latency A DSL service that automatically adjusts the transmissio

4-Port ADSL/ADSL2+ Wireless Router User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents