M21A-1111 User Guide
Contents
1. 3 Adjust the value of the adjustment items by pressing the Up or Down button 4 With the OSD menu on screen press Menu button to return main menu or exit OSD 5 The OSD menu will automatically close if you have left it idle for a pre set time 6 To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu will pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP or Down button c When the UP or Down button is released the previous setting will be saved and exit the Lock Un2. 800X600 800X600 832X624 1024X768 1024X768 1024X768 1280X1024 1280X1024 1152X864 1280X960 1440X900 1440X900 1680X1050 1680X1050 VGA only 1280X768 1920X1080 H Frequency khz 31 47 31 47 35 00 37 86 37 50 35 16 37 88 48 08 46 88 49 72 48 36 06 48 60 02 64 00 80 00 67 50 60 00 56 00 70 60 65 20 82 30 47 176 67 50 V Frequency hz 70 60 66 12 19 96 60 12 19 19 60 70 19 60 19 19 60 60 19 60 19 60 60 Touch Screen Driver Installation The M21A 0101 is available with USB connection The Linux kernel 2 6 x 32 bit amp 64 bit touch driver can be downloaded at www touchrev com HID for Windows 7 VISTA XP 2000 ME 98 Please Note 1 The M21A 0101 is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen 2 For M21A 0101 the system requires 15 seconds for Windows to install uninstall the touch drivers while turning power on off or plugging unplugging USB cable M21A 0101 Install Instructions If you are using a PC running driver Linux kernel 2 6 x 32 bit amp 64 bit follow the instructions below 1 The driver can be downloaded at www touchrev com 2 Poweron the PC 3 Be sure the USB cable is connected from the PC to the LCD display 4 Follow the step by st
3. the Audio In cable from the audio input port of your display to the Audio out port of your computer 10 1 5 Connect the USB cable from the USB port of your display to the USB port 10 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 20 7 Once the touch screen is configured the monitor is ready for use N Notice To ensure the LCD display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1920 x 1080 resolution and make sure the timing of the display mode is compatible with the LCD display We have listed the compatible Video Modes of your LCD display in the appendix on page 19 for your reference Figure 10 1 User Controls Side Panel Controls key Name E Menu A Up Down el Enter rr ELM Zac Bul Power Menu appear appear Menu Menu disappear return to main item return to main item ERN Brightness Main item select up Adjust up NE we Main item select down Adjust down Enter Select sub item function Power On Off How to Use the OSD Menus key Name E Menu A U v Down 4 Enter b Power HU 1 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the six functions in the main menu 2 Choose the adjustment items by pressing the Enter button
4. the screw hole is 8 mm A Warning Please select the proper screws Please use four M4 screws of adequate length for mounting your monitor Please note the mounting stand must be able to support at least 17 6 Ibs 8Kg Start Your Installation 1 Lay the LCD flat on an even surface 2 Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram 3 Move the stand into position as seen in step 3 diagram 4 Connect the cables to the appropriate connectors as seen in Step 4 diagram 5 Take the optional cable cover and screw from the accessory box Position all cables under the cover lip as seen in the step 5 diagram 6 Using a Philips Head screwdriver insert the screw CBM M3 into the cable cover and monitor as seen in the step 6 diagram 7 Re attach the stand back cover to the LCD stand by pressing firmly until the tabs snap into place as seen in the step 7 diagram You may also keep the cables in order by using the cable organizer Connecting the Display Figure 10 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 10 1 3 Connect the D SUB or DVI cable from the display s VGA input connector to the D SUB or DVI connector of your host computer and tighten the screws 10 1 4 Connect
5. USER s GUIDE Touch Revolution The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other electronic waste that can be hazardous if not disp
6. e electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do e Turn off the product before cleaning Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol Use a soft cloth moistened with mild detergent to clean the display housing Don t Do not touch the LCD Display screen surface with sharp or hard objects Do not use abrasive cleaners Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About M21A Series The M21A Series is a 22 flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD Features include Direct Analog signal input Direct Digital signal input Active matrix TFT LCD technology 1920 x 1080 resolution 22 viewable display area 16 9 aspect ratio 31 47 82 3 KHz horizontal scan 56 75 Hz high refresh rate 0 24825mm x 0 24825mm pixel pitch Auto adjustment function Multilingual OSD user control Kensington security slot 100 mm VESA mount Removable base for flexible mounting solutions M21A 0101 Projected Capactive touch screen with USB controller Aud
7. ep instructions as shown on the pop up windows
8. io 2W x 2 Touch Screen for M21A 0101 e Project Capacitive touch screen for finger input only e Surface Clear glass e Interface USB controller HID Windows 7 VISTA 2000 ME 98 Driver Linux kernel 2 6 x 32 bit amp 64 bit Package Overview Power Cord USB Cable Ato B Audio in Cable DVI D Cable Quick Start Guide Cable Cover Screw Installation Product Overview e Front View Bottom View Without Stand Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included J o0 0 0 0 0 0 O 0 0 0 0 O0 O o 0 6 0 0 o o o o o o o Bo B o VESA Mount for your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on a UL certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 100mm Slots x 4 o o o o A The distance between the shielding surface and the bottom of
9. ive or our service center Problem No image appears on screen Check that all the I O and power connectors are correctly and well connected as described in the Installation section Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image Check to see if the resolution of your computer is higher than that of the LCD display Reconfigure the resolution of your computer to make it less than or equal to 1920 x 1080 Problem Image has vertical flickering line bars Use Fine to make an adjustment Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display Problem Image is unstable and flickering Use Horizontal size to make an adjustment Problem Image is scrolling Check and make sure the VGA signal cable or adapter is securely connected Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Vague image characters and graphics Use Fine to make an adjustment If this problem still exists use Horizontal size to make an adjustment Warning Signal If you see warning messages on your LCD screen this means that the LCD display cannot receive a clean signal from the computer graphics card There may be three sources for this problem Please check the cable connecti
10. lock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key On Screen Display Menus Main OSD Menu ITEM Contrast Brightness Auto Adjust Left Right Up Down Horizontal size Fine OSD Left Right OSD Up Down OSD Time out OSD Language Factory Reset RGB Volume Mute CONTENT The monitor luminance level control The monitor backlight level control Fine tune the image to full screen automatically Moving screen image horizontal position to left or right Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment The screen image pixel phase adjustment Moving OSD menu horizontal position to left or right Moving OSD menu vertical position to up or down OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch opanish Italian Traditional Chinese and Simplified Chinese Factory default value restored Color temperature selection 9300K 6500K 5500K 7500K User Audio volume adjustment Audio On Off control Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following If the problem persists please contact your sales representat
11. ons or contact your sales representative or our service center for more information No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA DVI signal cable Going to Sleep The LCD display is under the power saving mode In addition the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the LCD display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the LCD monitor will display this message Product Dimensions 539 19mm 330 65mm 384 13mm Front View Side View 327 4mm E E N 00 N Top View Rotate 71 90mm 330 65mm 573 40mm 539 19mm Front View Side View 327 74mm Top View Mode IBM VGA IBM VGA Apple Macll VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA Apple Mac VESA XGA VESA XGA VESA XGA VESA SXGA VESA SXGA VESA SXGA VESA SXGA WXGA WXGA WSXGA WSXGA VESA WXGA WSXGA Compatibility Modes Resolution 720X400 640X480 640X480 640X480 640X480 800X600 800X600
12. osed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG Table of Contents Usage Notice SS eesti 1 Introduction ABOU RETA A E A oa aaa en 2 Touch Screen for M21A 0101 rr 3 Package Overview aaa aaa 4 Installation A A 5 mieu s NRI B Bottom View Without Stand E REC 5 Kensington Security nana 6 VESA Mount for your o T eh TOE EE iaa TETTE 8 Connecting the Display Figure TO T used 10 CRIAS E 11 User Controls es Ac pedro 12 How 10 Lise NE OSD MEDUS sumarse oi 13 On Screen Display MENUS TTL 14 Appendix TI MOS UN nico pili 19 Wa mmm 16 plea EN ne ee ere 16 ci 16 E E E E 16 Product Dimensions sara di a Hug Rd vu Re ea Kd nda 17 Fe yg s ee eee T EP 19 Touch Screen Driver Installation sosa repre 20 M21A 0101 Install InstructionS sierra rica sat 20 Usage Notice Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture Warning Please do not open or disassemble the product as this may caus
Download Pdf Manuals
Related Search