Qubino Flush dimmer - smart
Contents
1. 0 Reporting Disabled 1 65535 1 second 65535 seconds Reporting enabled Power report is send with time interval set by entered value Parameter no 60 Minimum dimming value Available configuration parameters data type is 1 Byte DEC Default value 1 Minimum dimming value is 1 1 98 1 98 step is 1 Minimum dimming values is set by entered value NOTE The maximum level may not be lower than the minimum level 1 min dimming value is defined by Z Wave multilevel device class Parameter no 61 Maximum dimming value Light types which support dimming function Available configuration parameters data type is 1 Byte DEC Default value 99 Maximum dimming value is 99 The classical incandescent light 2 99 2 99 step is 1 Maximum dimming values is set by Halogen lamps operated by 230 V AC High Voltage Halogen entered value Low voltage halogen lamps with electronic or conventional NOTE The maximum level may not be lower than the minimum level transformer 99 max dimming value is defined by Z Wave multilevel device class r Dimmable fluorescent Light e Dimmable compact fluorescent light CFL Parameter no 65 Dimming time soft on off Dimmable LED lights Set value means time of moving the Dimmer between min and max dimming values by short press of push button 11 or controlled through Ul Important disclaimer Available configuration parameters da2. LLON is not active ALL OFF is not active e 1 ALLON is not active ALL OFF active e 2 ALLON active ALL OFF is not active Dimmer module responds to commands ALL ON ALL OFF that may be sent by the main controller or by other controller belonging to the system Parameter no 30 Saving the state of the device after a power failure Available configuration parameters data type is 1 Byte DEC default value 0 0 Dimmer module saves its state before power failure it returns to the last position saved before a power failure 1 Dimmer module does not save the state after a power failure it returns to off position Parameter no 40 Power reporting in Watts on power change Set value means percentage set value from 0 100 0 100 Available configuration parameters data type is 1 Byte DEC default value 5 0 Reporting Disabled 1 100 1 100 Reporting enabled Power report is send push only when actual power in Watts in real time change for more than set percentage comparing to previous actual power in Watts step is 1 NOTE if power changed is less than 1W the report is not send pushed independent of percentage set Parameter no 42 Power reporting in Watts by time interval Set value means time interval 0 65535 in seconds when power report is send Available configuration parameters data type is 2 Byte DEC default value 300 power report in Watts is send each 300s
3. Qubino The INNOVATIVE and SMALLEST Flush dimmer Ordering code ZMNHDA2 Type Flush dimmer This Z Wave module is used for dimming the light or to manage the speed of a fan The module can be controlled either through a Z Wave network or through the wall switch The module is designed to be mounted inside a flush mounting box and is hidden behind a traditional wall switch Module measures power consumption of light or fan and supports connection of digital temperature sensor Supported switches Module supports mono stable switches push button 11 Installation Before the installation disconnect power supply Connect the module according to electrical diagram o Locate the antenna far from metal elements as far as possible Do not shorten the antenna Danger of electrocution e Module installation requires a great degree of skill and may be performed only by a qualified and licensed electrician 2 Even when the module is turned off voltage may be present on its terminals Any works on configuration changes related to connection mode or load must be always performed by disconnected power supply disable the fuse Note Do not connect the module to loads exceeding recommended values Connect the module only in accordance to the below diagrams Improper connections may be dangerous Package contains Flush dimmer Electrical diagram 230VAC L N 11 12 13 Q L N 5 Notes for t
4. conds or press push button l1 five times within 3s 5 times change switch state within 3 seconds By this function all parameters of the module are set to default values and own ID is deleted If service button S is pressed more than 2 and less than 6 second module is excluded but configuration parameters are not set to default values Association Association enables Flush dimmer module to transfer commands inside Z Wave network directly without main controller to other Z Wave modules Associated Groups Group 1 multilevel triggered at changes of state value of the Flush dimmer Group 2 basic on off triggered at change of the input 12 state and reflecting its state Group 3 basic on off triggered at change of the input I3 state and reflecting its state Group 4 default reporting group reserved for the main controller Configuration parameters Parameter no 2 Input 2 contact type Available configuration parameters data type is 1 Byte DEC e default value 0 e ONO normaly open input type e 1 NC normaly close input type Parameter no 3 Input 3 contact type Available configuration parameters data type is 1 Byte DEC e default value 0 e ONO normaly open input type e 1 NC normaly close input type Parameter no 10 Activate deactivate functions ALL ON ALL OFF Available configuration parameters data type is 1 Byte DEC e default value 255 e 255 ALL ON active ALL OFF active e 0 A
5. d load current of AC output 0 85A 230VAC Rated load current of DC output 0 85A 30VDC Output circuit power of AC output resistive load resistive load K CE Ss Frequency Range 868 42MHz Z Wave Qubino Digital temperature sensor range 50 125 C Goap d o 0 Nova Gorica sensor must be ordered Ulica Klementa Juga 007 separately 5250 Solkan Operation temperature Slovenia Distance up to 30 m indoors depending on building materials E mail info qubino com Dimensions W x H x D 41 8 x 36 8 x 15 4mm Tel 386 5 335 95 00 Weight Web www qubino com Electricity consumption For installation in boxes gt 60mm or 2M itchi MOSFET Date 24 04 2014 max 100W mono phase asynchronous fan motor can be Document Qubino_Flush dimmer user connected to dimmer output manual_V3 0_eng
6. he diagram Neutral lead Live lead Output for electrical device Input for switch push button or sensor Input for switch push button or sensor Input for push button Terminal for digital temperature sensor only for Flush dimmer module compatible digital temperature sensor which must be ordered separately Electrical diagram 24VDC w 11 12 13 Q L N Notes for the diagram 24VDC 24VDC Output for electrical device Input for switch push button or sensor Input for switch push button or sensor Input for push button Terminal for digital temperature sensor only for Flush dimmer module compatible digital temperature sensor which must be ordered separately S Service button used to add or remove module from the Z Wave network Module Inclusion Adding to Z Wave network Connect module to power supply bring module within maximum 1 meter 3 feet of the main controller enable add remove mode on main controller auto inclusion 30 minutes after connected to power supply or e press service button S for more than 2 seconds or press push button I1 three times within 3s 3 times change switch state within 3 seconds Module Exclusion Reset Removing from Z Wave network Connect module to power supply o bring module within maximum 1 meter 3 feet of the main controller enable add remove mode on main controller press service button S for more than 6 se
7. ta type is 1 Byte DEC Default value 1 Dimming ti in dimmi etal vale LOO Dimming ims betwasn min and max gimiming Z Wave wireless communication is inherently not always 100 reliable VORAS and as such this product should not be used in situations in which life 1 255 10mseconds 2550mseconds 2 55s step is and or valuables are solely dependent on its function 10mseconds Warning Parameter no 66 Dimming time when key pressed Time of moving the Dimmer n min and m immin neo nO ie DUNE s Dele mination N E ase Do not dispose of electrical appliances as unsorted municipal waste continues hold of push button 11 Hauk use separate collection facilities Available coniguralion parameters data ype eh Byte DEG Contact your local government for information regarding the collection Default val Dimmi i in dimmi i Pranit valle S AMIM Mime ENNS M Ane mer Clmmning systems available If electrical appliances are disposed of in landfills or values is 3s dumps hazardous substances can leak into the groundwater and get 1 255 1 second 255 seconds into the food chain damaging your health and well being When replacing old appliances with new once the retailer is legally obligated Technical Specifications to take back your old appliance for disposal at least for free of charge 0 Powersupply TO RUVAR AO OO This user manual is subject to change and improvement without notice 24 30VDC Rate
Download Pdf Manuals
Related Search