User manual
Contents
1. SANTEC HD CVI PTZ Speed Dome Model SCC 242KZNA Version 1 0sfi 0715 engl A5 Dear customer Thank you for purchasing a high quality SANTEC device We recommend that you read this manual thoroughly before operating your new system for the first time Please follow all instructions and observe the warnings contained in this manual Please contact your local dealer or SANTEC directly if you have any questions or if you wish to claim for a service or warranty You will find further information on our website www santec video com Imprint All rights reserved This publication may not be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the written prior permission of SANTEC BW AG No reproduction of any part or excerpts thereof are permitted Errors excepted Specifications are subject to change without notice for quality improvement SANTEC is a registered trademark of SANTEC BW AG All other companies or products mentioned in this publication are trademarks registered trademarks or brands of the respective company Copyright SANTEC BW AG An der Strusbek 31 22926 Ahrensburg Germany www santec video com User Manual SCC 242KZNA em Table of contents oafety precautions oafety instructions About this user manual PART I CAMERA DESCRIPTION TECHNICAL SPECIFICATIONS INSTALLATION 1 I2. ee available if WB Mode is set to Manual B Exit Exposure AE Mode AG SSS SS exposure settings Setting Auto Manual Iris Prio Shutter Prio Gain Setting Shutter SUE 1 3 1 6 1 12 1 25 1 50 1 75 1 100 1 120 1 150 1 215 1 300 1 425 1 600 1 1000 1 1250 1 1750 1 2500 1 3500 1 6000 1 10000 1 30000 1 18 Compensation Backlight compensation on off Slow Shutter Lower the camera auto exposure time Especially mm for lower illumination environment 1 1 1 2 1 3 1 6 1 12 1 25 Noise reduction Off 1 16 CKamera 3D noise reduction Off 1 16 High light reduction Off 1 4 Off 1 hour 2 hours 5 min 15 min 30 min WDR Mode Wide Dynamic Range On Off Back Exit O continue on next page 20 User Manual SCC 242KZNA SANTEC Menu item Sub menu item Additional items Remarks Day Night Day Night Day night switching Setting Auto Night Day De Mechanism Electron Threshold owitching the day night mode according to the here defined threshold 1 8 Back Setting Auto Semiauto Manual Auto 10cm 1m 2m 3m 5m Low Mid High Off On Auto EEE Image Adjust Back Exit Zoom Speed 1 8 Zoom speed can also be set in PTZ control menu see chapter 2 Next Page L0 1 16 0 0 Restrain low illumination environment Digital Zoom Off Ew Initialisation Picture Mode 1080P 25 1080P 30 Resolutio
3. Define whether the menu is to be protected by a password On Off Set the password for accessing the OSD menu and then Save it Password protection is then active see above Note If an invalid password is entered three times the system shows an 8 digit internal code Please contact the technical engineer for help If you set a time here the OSD menu will disappear once this time has elapsed If you select Off the OSD menu will be displayed at all times If you wish to close hide theOSD menu click on Enter or Exit see below PTZ Auto 5 10 15 20 25 30 sec The dome will stop all PTZ operations when there Stop Off is no command for the specified time TS 95 User Manual SCC 242KZNA em SANTEC 3 2 5 Alarm Setting Use the up down arrows in the Menu Operation window to select the menu item Alarm Setting It is now marked with a diamond Confirm your selection by clicking on Enter Use the up down arrows to select a sub menu item Use Enter to confirm your selection Use the left right arrows to changes the values if available Sub menu item Additional EE items Remarks Alarm No 1 2 Alarm numbertor2 number1 or 2 Preset Tour Action the dome has to perform if an alarm ocan occurs Parameter Select the number of preset tour scan aus N O N C Normal Open Normal Close Relay Out Off 1 5 sec Relay 1 w
4. object area which you would like to mask should be positioned in the center of the video image because the privacy zone will be positioned in the center of the image too The position of the privacy zone cannot be changed later but only its size e Go to the Privacy Masking menu and then on Setting and Resize e Resize Adjust the size of the privacy zone Reduce the width of the privacy zone Enlarge the width of the privacy zone T Enlarge the height of the privacy zone 1 Reduce the height of the privacy zone After you have selected one of the adjustment arrows click on the Enter button several times until the zone has reached the desired size e Goto Save e For Activate please select The privacy zone is now displayed in the video image Privacy zones cannot be deleted but only be enabled shown or disabled hidden and they can be resized see above Back Exit continue on next page 94 User Manual SCC 242KZNA Le MEE PTZ Speed Menu Password Menu Idle PTZ Correction Back Exit mE IL RN Back Exit Password Setting Back Exit Off 1 min 2 min 3 min 4 min 5 min On Off Additional items Remarks Move the dome to the horizontal coordinates Define the PTZ action the dome has to assume it is booted None auto preset pattern tour scan ne the number for prreset pattern tour scan
5. 485 connection the Dip switches have no function Once you removed the housing cover as described in chapter 3 you will have access to the the Dip switches Adress setting Adress setting N ON N ON ON User Manual SCC 242KZNA eum SANTEC Baudrate and parity Setting the Baudrate switches 1 and 2 ENERR TN o OFF 9600bps Einstellung der Paritat Schalter 3 und 4 The following default settings apply factory default Address 1 Baudrate 9600 Parity None If you change the Dip switch settings you need to reboot the camera Please ensure that the settings address Baudrate parity of the device connected via RS 485 align with the camera SCC 242KZNA SANTEC 6 Installation The dome camera can be ceiling or wall mounted Please ensure that the surface is solid enough to carry the weight of the dome camera For safety reasons it is recommended to ensure that the surface can carry 8x the camera weight If you need to set the Dip switches please do so before the installation see chapter 4 e Remove the housing cover see chapter 4 e Use the supplied mounting drawing paper to position the drilling holes Use the anchors sleeves and screws to mount the housing bottom on the ceiling wall e The cable containing the various connections can either be led through the housing s side or its bottom additional drilling hole required e Put the housi
6. Openings in the appliance if any are provided for ventilation to ensure reliable operation of the appliance and to protect if from overheating These openings must not be covered or blocked Please make sure that the appliance does not overheat e he appliance should only be operated from the type of power source indicated on the marking label If you are not sure of the type of power supplied at the installation location please contact your local dealer e An appliance which is powered through a polarized plug a plug with one blade wider than the other will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug into the outlet try reversing the plug Do not defeat the safety purpose of the polarized plug e f the appliance is powered through a grounding type plug the plug will only fit into a grounding type power outlet This is a safety feature If your outlet does not have the grounding plug receptacle contact your local electrician e Route power cords and cables in a manner to protect them from damage by being walked on or pinched by items places upon or against them e For protection of the appliance during a lightning storm or when it is left unattended and unused for a longer period unplug the appliance from the wall outlet Disconnect any antennas or cable systems that may be connected to the appliance This will prevent damage to the appliance due to lightning or power line surges
7. and if an external RS 485 devices is connected because otherwise you will neither have access to the dome nor access to the OSD menu and no way of resetting to the dome to HD 3 2 2 Display Setting Use the up down arrows in the Menu Operation window to select the menu item Display Setting It is now marked with a diamond Confirm your selection by clicking on Enter Use the up down arrows to select a sub menu item Use Enter to confirm your selection Use the left right arrows to changes the values if available Menuitem Sub menuitem Additional items Remarks Preset Title On Off Display the preset title preset settings see chapter 3 2 4 Display the coordinates x y axis into the video Display image current location sg Display tempore on Temperature Domy E Display Display SS _ Back Ext fo num User Manual Eee SCC 242KZNA SANTEC 3 2 3 Camera Setting Use the up down arrows in the Menu Operation window to select the menu item Camera Setting It is now marked with a diamond Confirm your selection by clicking on Enter Use the up down arrows to select a sub menu item Use Enter to confirm your selection Use the left right arrows to changes the values if available Additional items Remarks WB Menu em WB Mode White balance settings Auto Manual ATW Outdoor Indoor Outdoor Auto NA Lamp NA Lamp Auto only for externally added illuminators RGan
8. if you use the PELCO protocol the following special preset commands apply e Call preset e Preset 28 or 95 Preset 29 or 99 Preset 24 or 81 Preset 25 or 82 Preset 30 or 96 Preset 31 or 83 Preset 33 e Preset 34 e Set preset e Preset 26 or 92 e Preset 27 or 93 e Preset 22 or 79 e Preset 23 or 80 Call up the OSD menu Call up the scan function Call up the pattern function Call up the tour function Stop scan or pattern otart dome rotation otart 180 dome rotation oet dome position as zero Set left scan limit oet right scan limit Start record Stop record 99 SCC 242KZNA User Manual SANTEC Menu item Sub menu item Additional items Remarks Auto Pan Pan speed 1 8 Alternatively set the speed using the PTZ contorl menu see chapter 2 __ Manual start The dome begins 360 continuous EE eS Back Ext ss Auto Scan Set Left Limit Limit the left scan area range e Go to the PTZ control menu and move the dome to the position of the left limit e Go to the auto scan menu Define a scan number see above e Goto Set Left Limit and confirm with Enter OK pops up briefly The left limit is now set Set Right Limit Limit the righ scan area range e Goto the PTZ control menu and move the dome to the position of the righ limit e Goto the auto scan menu e Goto Set Right Limit and confirm with Enter OK pops up br
9. C Declaration of Conformity for this device please send a request to CE santec video com Attention Any changes or modifications to this appliance which have not been explicitly approved of by the respective regulatory authority may lead to a prohibition of usage of this appliance Important Legal note Monitoring recording and storage of video surveillance data images sound is subject to strict legal regulations Please respect the Data Privacy Act which applies to your country User Manual SCC 242KZNA em SANTEC Safety instructions e Before operating the appliance please read this manual carefully and retain it for further reference e Before cleaning the appliance it has to be switched off and unplugged from the power outlet Wipe the appliance with a soft damp cloth Do not use harsh cleansers or aerosols for cleaning The type label may not be replaced e Do not use attachments unless recommended by the manufacturer as they may affect the functionality of the appliance and result in the risk of fire electric shock or injury e Never install the appliance in areas exposed to water or other liquids e The appliance has to be installed in a safe and stable location according to the instructions of the manufacturer Care should be used when moving heavy equipment Quick stops excessive force and uneven surfaces may cause the appliance to fall Causing serious injury to persons and damage to objects e
10. NTEC HD CVI recorder model SCVR 2411K It is exemplary for the other SANTEC recorders models 2 Calling up the PTZ control menu Login to the recorder using your user name and password If you are in live view mode either in multi split mode or in full screen mode right click to call up the quick menu ree Use the menu item Pan Tilt Zoom to call up the PTZ control menu of Color Setting the dome camera Search Left click into the live view to close the quick menu again Manual Menu If you click on Pan Tilt Zoom the following PTZ control menu d 2 pee _ Zoom Focus ES Iis WE X Fr Le it Speed Define the speed for the PTZ movements 1 8 Click on the speed number to bring up the virtual keyboard Enter the desired speed Alternatively you can set the speed using the OSD menu see chapter 4 4 Function Setting gt Auto Pan Pan Speed User Manual ms SCC 242KZNA SANTEC Zoom Focus Iris Use the plus minus buttons to adjust the zoom focus and iris PTZ direction Use the 8 direction arrows to move the dome into the desired direction Select zoom area Q In the center of the direction arrows you will find a button to select a zoom area Click on this center button Then use the mouse to draw an area into the image which you would like to zoom in Release the mouse button and the selected area will be z
11. e Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock e Never insert items into the openings of the appliance They may touch parts under electric current which may cause an electric shock e Never pour any liquids over the appliance e Incase of any operating interruption or a complete operating failure please switch off the appliance and disconnect it from the wall outlet Never attempt to service or repair the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel e When replacement parts are required be sure that the service technician uses replacements parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards User Manual SCC 242KZNA e Upon completion of any service or repairs to the appliance ask the service technician to perform safety checks to verify that the appliance is in proper operating condition e appliance should only be installed by qualified service personnel and has to comply with local specifications and regulations e Never point the camera at an object with a high degree of luminance Bright vertical or horizontal lines can result in a distortion outshine of the entire image on the monitor This artifact is not an error but a particularity
12. enchmark direction to that you can know the angle between the benchmark and the current location Click Enter to see OK Now you have set the north direction Englisch No other language available at the moment Video Output HD SD See next page Importante note Factory Restore to factory default settings Default Restat Restart Reboot the camera Back User Manual SCC 242KZNA SANTEC Important note on menu item Video Output HD SD It is possible to change the video output from HD CVI item HD in the OSD menu to 960H CVBS analogue item SD in the OSD menu If you do so please note the following When changing the video output of this HD CVI dome from HD to SD the dome will behave like a SD dome thus an analogue dome In general analogue domes can neither be controlled via a coax link nor by a connected recorder instead they can only be controlled via the RS 485 connection This means that you have to connect an external RS 485 device to the RS 485 port of the dome e g a control keyboard in order to change the dome s parameters Access to the OSD menu is only possible via the external RS 485 device If there is no external RS 485 device connected to the dome you cannot reset the video output from SD to because this would require access to the OSD menu For this reason the video output should only be changed to SD and thus to analogue if absolutely required
13. enu The Menu Operation window is still displayed To close the Menu Operation window as well right click into the video image User Manual SCC 242KZNA SRNTEC 3 2 PTZ functions using the OSD menu Navigate through the OSD menu by using the Menu Operation window see chapter 2 You can define how long the OSD menu is to be displayed on the screen See chapter 4 4 Function Setting Next Page Menu Idle The OSD menu is currently only available in English It is structured as follows Main menu 1 System Setting Display Setting Camera Setting Function Setting Alarm Setting Exit 3 2 1 System Setting Use the up down arrows in the Menu Operation window to select the menu item System Setting It is now marked with a diamond Confirm your selection by clicking on Enter Use the up down arrows to select a sub menu item Use Enter to confirm your selection Use the left right arrows to changes the values if available Menuitem Sub menu item Additional items Remarks System Address Information Baudrate Parity 000 o O Version o O Camera Version O Back Address Select between Hard and Soft Information Address Hard Address for Dip switches cannot be edited by the software OSD menu Address Soft Address can be edited by the software OSD menu Back Exit Set North OK Set a dome b
14. er a preset number for this tour e Save the settings by clicking on Add preset e Use Del preset or Del tour to delete a preset or tour 28 SCC 242KZNA SANTEC Pattern e For pattern settings use the direction arrows to move the dome camera into the desired position Enter a pattern number Click on Begin or End Border n l Preset Use the direction arrows to position the camera within its left and right borders 29 SCC 242KZNA SANTEC 3 3 2 Aux on off Click on the aux symbol The follow window is displayed The settings defined here depend on the selected protocol Direct aux represent the aux on off button of a decoder 30 User Manual SCC 242KZNA SANTEC Notes 31 Your local distributor SANTEC www santec video com
15. iefly The right limit is now set Scan speed 1 5 Manual start The dome rotates in the defined limits otop Manual stop The dome stops rotating in the S9 limits Back Ext Tour 5 number 1 8 Setting For each tour presets dwell time and speed can be defined NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 013 32 000 005 013 BACK EXIT Delete the selected tour pops up briefly Start the selected tour manually Stop the selected tour manually Back continue on next page 992 M85 SCC 242KZNA SANTEC item Sub menu item Additional items Remarks si Pattern Stop the selected pattern manually _ the selected pattern manually Back Ext Exit Idle Motion ihe dome is We fora defined period of wae aU the dome is idle for a defined period of time you can define the action type it is to perform on off Type of action the dome is to perform after the defined time has elapsed None preset pattern tour scan Select the number for preselipattern tour scan _ the number for preset pattern tour scan Back Ext Exit Next Page Privacy ERES NS NO Privacy masking zones 1 24 These areas are covered hidden in the video image When the Masking dome moves the masked areas objects continue to be masked Enable disable the privacy zone On Off Setting Move the dome to the desired position The
16. ill be active for 5 seconds after an alarm occurs Reset Delay 3 10 30 60 120 sec The other alarm contacts will be active for the specified time Save Speichem O 3 2 6 Exit Use the up down arrows in the Menu Operation window to select the menu item Exit It is now marked with a diamond Confirm your selection by clicking on Enter The OSD menu is now closed 26 SCC 242KZNA mum User Manual SANTEC 3 3 Additional PTZ functions using the PTZ control menu Q O O JS 3 B Click on the symbols e g autoscan to execute this command it has to be defined accordingly Please read the inei d sections in chapter 3 i 4 Further explanations on Aux config and Aux on off are available in the following chapters S07 SCC 242KZNA SANTEC 3 3 1 Aux configuration Note The following settings can also be made by using the OSD menu see chapter 3 2 4 Click on the Aux config symbol E The following window is displayed Ma Preset Border Del Preset e For preset settings use the direction arrows to move the dome camera into the desired position e Enter a preset number e Save the settings by clicking on Set e Use Del preset to delete a preset Pattern reset 0 Acid Preset Del Preset Del Tour e For tour settings use the direction arrows to move the dome camera into the desired position e Ent
17. ing 2170mm 76mm 155mm j All dimensions in mm Drawing not true to scale oubject to technical changes Errors excepted SCC 242KZNA SANTEC 3 Connections The dome camera comes with the following connection options open cable ends Connection 24 Power Audio CA Yellow Y RS 485 A Yellow B Orange Aam INT Red Alarm with heat shrink tube Heat shrink tube The video connector is covered by a heat shrink tube Once you have connected the dome camera you may use a heating device e g a hot air gun to heat the tube to shrink fit it to the cable 4 How to open and close the housing To open the housing please loosen the screws and pull off the housing cover of the housing bottom To close the housing please ensure that the marks on the housing bottom and the one on the housing cover are aligned Then screw the housing tight Loosen 3x screws Align marks Notes e Transport securing ring Prior to the installation please open the dome housing and remove the white foamed ring which served as transport security e Do not remove the little sachet with dry granulate SCC 242KZNA SANTEC 5 Dip switch settings only for RS 485 connection Note Dip switch settings are only relevant if you connect an external device via RS 485 to the camera e g a control keyboard If you dont use the RS
18. n frae rate 720P 50 720P 60 Next Page 4 J Camera Reset the camera to factory default settings Factory Default Camera Restart reboot the camera Hestart Back Exit 0 91 User Manual SCC 242KZNA em SANTEC 3 2 4 Function Setting Use the up down arrows in the Menu Operation window to select the menu item Function Setting It is now marked with a diamond Confirm your selection by clicking on Enter Use the up down arrows to select a sub menu item Use Enter to confirm your selection Use the left right arrows to changes the values if available Menu tem ME S Additional items Remarks Preset 1 300 um Setting Preset title name is automatically assigned and is identical with the preset number e g cannot be edited Setting a preset e Go to the PTZ control menus and move the camera in the desired direction for the preset Go to the preset menu Define a preset number The preset title will be assigned automatically see above Go to Setting and confirm with Enter pops up briefly The preset is now set Go to and confirm with Enter to call up the preset Alternatively Open the PTZ control menu to call Back Exit continue on next page opecial presets for using PELCO protocol If you control the dome camera via an external control device e g KSC 3505 using the RS 485 connection and
19. ng cover back on see chapter 4 Mounting drawing paper Anchors Housing bottom Sleeves Screws 4 SCC 242KZNA SANTEC 7 Self diagnosis If you run the dome camera for the first time of if you have reset it to factory default settings the camera will perform a self diagnosis test The following information will be displayed for approx 4 minutes ADDR 001 H BR 9600 PARITY None VERSION V1 00 0 R The self diagnosis information will disappear if the dome receives the first command 192 User Manual SCC 242KZNA SRNTEC 8 Technical specifications Model SCC 242KZNA S HD CVI PTZ dome camera 1 2 8 2 Megapixel Exmor CMOS 1944 H x 1092 V 1080p 720p Pan 1 Tit 0 1 s 120 s Preset 300 s Pan a 0 05 Lux F1 6 Colour a ALON 0 005 Lux F1 ner NI CE VCA 12V 1 5ASA oubject to technical changes Errors excepted wires SCC 242KZNA SANTEC Part 11 Camera configurations via the connected recorder 1 General You cannot make any settings or configurations at the camera directly except for the Dip switches see part chapter 4 All camera configurations are made using the connected HD CVI recorder Recommended SANTEC HD CVI recorder models e SCVR 2411K e SCVR 2411TK e SCVR 2812TK Connect the dome camera a mouse and a monitor to the recorder Note The settings described in this manual are based on using a SA
20. of semiconductor CCDs when they are directly exposed to a powerful light source e f the camera is operated in locations with extremely differing light conditions the aperture has to be adapted e Please respect the local legal regulations on waste if you need to dispose of discarded appliances This symbol means that electrical appliances need to be disposed of properly and not simply with unsorted household refuse Please respect local regulations on waste disposal About this user manual This manual aims at assisting the user on how to operate the described cameras This manual is subject to rigid quality control However no guarantee can be given that mistakes are not present We reserve the right to make changes to the manual without prior notice Before operating the appliance please read this manual carefully and retain it for further reference Verify that all appliance items are included in the delivery Should items be missing do not operate the appliance and contact your local dealer Never attempt to repair the appliance yourself This should only be done by qualified service personnel Improper handling of the appliance will invalidate the warranty Subject to technical changes without prior notice Errors excepted SCC 242KZNA SANTEC 1 Items included in the delivery 1x Camera SCC 242KZNA 1x Allen wrench 1x Mounting drawing paper 1x Quick installation guide and security notes 2 Technical draw
21. oomed in at max 16x speed The smaller the selected area the higher the zoom speed To return to the normal view there are 2 options 1 In the PTZ control menu click on the minus zoom button 2 Use the mouse wheel 15 SCC 242KZNA SANTEC 3 PTZ functions using the PTZ control menu 3 1 Calling up the OSD menu of the PTZ dome camera 1 Call up the PTZ control menu as described in chapter 2 2 Inthe PTZ control menu click on the arrow on the right hand side to extend the menu Speed 2 Speed 2 Zoom Zoom ES L Orjo 2 VIRE d 5 ris 7 AOR is Speed 2 E Zoom p Focus M amp 4 A window called Menu Operation as well as the OSD menu are displayed in the video image OSD menu Menu Operation 16 SCC 242KZNA User Manual SANTEC OSD menu settings using the Menu Operation window Use the displayed Menu Operation to navigate through the OSD menu by clicking on the arrows Note You cannot mouse click directly on a OSD menu item but you have to use the arrows in the Operation window Arrows up down Scroll up down the OSD menu to select a menu item The selected item is marked with a diamond icon Enter Click Enter to confirm the selection of an item A sub menu is opened if available Arrows right left Use these arrows to adjust values ESC Click ESC to close hide the OSD m
22. tems included in the delivery 2 Technical drawing 3 Connections 4 How to open and close the housing 5 Dip switch settings only for RS 485 connection 6 Installation 7 Self diagnosis 8 Technical specifications PART Il CAMERA CONFIGURATION VIA A CONNECTED RECORDER 1 General 2 Calling up the PTZ control menu 3 PTZ functions using the PTZ control menu 3 1 Calling up the OSD menu 3 2 PTZ functions using the OSD menu 3 2 1 System setting 3 2 2 Display setting 3 2 3 Camera setting 3 2 4 Function setting 3 2 5 Alarm setting 3 2 6 Exit 3 3 Additional PTZ functions using the PTZ control menu 3 3 1 Aux configuration 3 3 2 Aux on off SANTEC O1 SCC 242KZNA SANTEC Safety precautions Caution CAUTION DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Description of symbols Danger This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person operating and maintenance servicing instructions in the literature accompanying the appliance 1 Warning This symbol is intended to alert the user to the presence of important CE compliance This appliance complies with the CE guidelines If you require an E
Download Pdf Manuals
Related Search