"user manual"
Contents
1. DTC location and fixing height 7 3 Installation Procedure Installation of solar heating systems can be carried out under all conditions normal to roofing work and within the building under all conditions normal to plumbing work and must be carried out in accordance with the manufacturer s instructions The following points must also be considered in addition to those raised during the site survey collectors must be installed by persons qualified to carry out such work with suitable training and practical experience of solar collectors the collector must be fixed directly to the roof structure or structural substrate as referred to in Section 4 2 _ particular attention must be paid to correct fitting of all components and to the detailing and positioning of gaskets and areas where pipe work enters the building the system controller and associated pipe work should be installed by a person qualified to do this work collectors should remain covered until commissioning has been completed prior to handover to prevent formation of unwanted oxides on internal collector surfaces during prolonged periods with no heat extraction 25 pr SR 50 2 2010 E 26 solar pump or other similar solar primary item should be connected via heat resisting flex cord not fixed cable marked to tolerate at least 85 C and be fitted on the cooler return run to the solar collector fixed wiring should be clipped cor2. the seals must be in good condition the roof fixings must be tight and secure the roof covering must be satisfactory flashings and roof covering underlay penetration points must be in good condition fluid levels in the cistern vessel or pressure gauge must be checked against the levels specified at commissioning 27 pr SR 50 2 2010 E the pressure relief valves should be checked to ensure it is not stuck open or closed the pressure in the system should be checked to ensure it has not dropped below the level set when commissioned flow indicator gauge should still display circulation rate set by solar system designer electrical controls and temperature sensors must be operating correctly the circulating pump must be operating without undue noise pipe work insulation must be firmly in place there must be no condensation or damp spots particularly around the pipe work and fixings in the roof space all safety and information labels must be in place if antifreeze is used with the system it should be tested at least every 3 years or at greater frequency if advised by the manufacturer some antifreeze products require regular replacement the solar cylinder should be checked to ensure the temperature settings are correct the ph of the primary liquid should be checked a low level indicates high acidity which will reduce life expectancy of compon
3. NSAI Standards Draft for Public Comment Number SR 50 2 2010 Title Code of practice for building services Part 2 Solar panels This document gives general guidelines for design installation and commissioning of solar heating systems in single dwellings Enquiry period 28 May 2010 to 27 August 2010 Readers are warned that this draft is subject to ongoing development and change Please send your comments on the comments sheet available on www NSAL ie to gay moran nsai ie or NSAI 1 Swift Square Northwood Santry Dublin 9 Date 2010 05 pr SR 50 2 2010 pr SR 50 2 2010 E pr SR 50 2 2010 E Contents Page Taicere 8 e C0 PA Speciale net ee EE 4 1 SCONE ee EE Eeer A 2 Klsidu EICH TEEN 7 3 Solar heating systems General requirement ccsecceeseeeesseeenseeeeeeeeeseaeseseeeenseeeeesaeseneaeenseeeeeees 10 3 1 GME E 10 3 2 Minimum SPeCifiCAtIONS cceceeeceeeeeee cece eeee eee enneee seen neeeee ea neeeee ea geeeee ea seeeeeenseeeeeeenseeeeeeaseeeeesseeeenenseeenes 10 3 2 1 Technical specifications ccceeecccseeeeeeeeeeeeee een eeeeeeenseeeeenseeeeeenseeeeenseeeeenseneeeeeeseneeeedseeeeeaseeeenenseeenes 10 3 2 2 Minimum provisions for labelling commissioning and documentation eccseseerseeeeneees 10 3 3 Safety Considerations i mi ieee iesene eao iinan eaae aaien aoas eaat oaaao aia aa anaa eaa aea de aa aat kaain 10 E NR E BE 10 3 3 2 LO CATION ACCESS E
4. 3 3 2 Location Access The solar heating system shall be installed so as to provide reasonable and safe access for maintenance cleaning repair or replacement Consideration should be given to building height site exposure including impact relative location of conservatories power phone lines porches skylights dormers etc provision of a roof ladder or a safety harness anchorage point for use during inspection maintenance may need to be considered avoid compromising access to any existing equipment e g mechanical or electrical avoid compromising the operation of existing doors windows etc limit risk of components becoming detached or falling off avoid compromising the fire safety of the building itself or adjoining buildings see Appendix C minimise and withstand the pressures due to wind loading suction include provision for access within the roof spaces for maintenance of the system Where necessary walkways may need to be constructed to offer safety and protection for integrated in roof collectors a loft space should be provided behind the collectors for accessing the pipe connections and or replacing temperature sensors 11 pr SR 50 2 2010 E 3 3 3 Layout of pump station and cylinder consideration should be given to space requirements of hot water storage systems at the design stage all safety features of the system should have sufficient clear space for in
5. Annual solar radiation in kWh m Tilt of Orientation of collector Note Data taken from SEAI DEAP Manual 4 2 Behaviour in Relation to Fire Collectors should be classified in accordance with Appendix A of Building Regulations TGD B Fire Safety when assessed in accordance with BS 476 3 or equivalent Collector panels which are integrated with the slates or tiles should have A or AA rating The provisions of 3 2 5 11 of Building Regulations TGD B must be met for locations near compartment walls i e a zone of the roof at 1 5 m wide on both sides of the wall should have a covering of class AA AB or AC or European Class Broor t4 For locations near boundary walls the roof covering should be class AA AB or AC or European Class Broor t4 as stated in Table 4 4 of Building Regulations TGD B Where pipes pass through fire rated walls or cavity barriers they should be adequately fire stopped without compromising provision for thermal expansion Combustible materials should not be exposed to solar heating equipment having operating temperatures which can cause ignition Proper clearances shall be specified and maintained 16 pr SR 50 2 2010 E 4 3 Structural Performance The collector fixings and the roof structure or any modifications to it must be designed and constructed by persons suitably qualified to carry out such work to support for the required design life To dead loads of all components including liqu
6. Pumps and controls should be in the normally heated area of a house Advanced DTCs use temperature linked speed control of the circulating pump to maintain higher efficiency heat transfer It is recommended that the controller should count the number of operating pump hours for maintenance purposes A solar primary system should include a manual override to engage circulation for commissioning in all weather conditions with a means of accurately indicating primary circulation rate Signage fixed in a prominent location close within the pre heat store is recommended Signage should contain details of installers plumber electrician etc person that commissioned the system their contact details key maintenance requirements next service warning of high temperatures to solar components advice on control of access to the store etc 3 3 9 Lightning protection The risk of property damage or loss of life due to lightning is relatively low in Ireland for domestic properties Installation of solar heating systems in domestic properties does not generally increase the level of risk particularly as collectors tend to be located below ridge level and are not higher than the chimney However the risk of lightning should be assessed for individual buildings in accordance with I S EN 62305 In general where a building requires specific lightning protection the solar collector should be connected to the lightning protection system As a minimum all p
7. 11 3 3 3 Layout of pump Station and cylinder ccceseeeeeeeseeeee een seeeeeenseeeeeenseeeeeenseeeeeenseneeeenseeeeeeenseeeneneeenes 12 3 3 4 Risk of bacterial growth legione ha seccceseeeeeeeseeeeeenseeeeeensneeeeeenseeeeeenseeeeeenseeneeeasneeeeeenseeeeeeseenenes 12 3 3 5 Unvented hot water storage SYStOMS ccccssseeeeeseeeeeenseeeeeenseeeeeeenseeeeeenseeeeeenseneeeeaseeeeeseseeeeneeseenenes 12 3 3 6 Existing UU Te E 13 3 3 7 Pressure relief VAlVOS cccccceseseeeeecee ee ee ee eeneeeeeee sense ea neeeeeeeseeeeensaneaeaeeeseeeeaaaneaeeaeeseeeeeesnaeaeseeeeaseneseanen 13 3 3 8 Differential thermostatic control 2 2 2 2 cceeeeeee cece cece eee ee ee eee e eens nnn eeee eee e ea sana neaeee sessed enna ENEE nnmnnn nnmnnn 13 3 3 9 Lightning e E 14 3 4 Materials EE 14 4 Solar collectors Requirements ccccceeeceeeeseeeeeeeeeeeeeeesneeseensnaeseeeeeaeseensnaaeseensnaeseensnaeseeneeseenenes 16 4 1 Positioning of collectors for maximum Solar efficiency ccceseeeeeseeeeeeeeeeeeeeseseeneeseseeeneeeeeenenens 16 4 2 Behaviour in Relation to fe LCE 16 4 3 Structural Performan Ce s vecc sceiicseesteccessceeiceadwccvessnwciveadseeesessnwerveasswervevssueieatssnersestavecveassivesevanuurvandsece 17 5 Solar collectors Design details and workmanship csssccsseeeeeseeseeeseseeeeeeeeeeseeeseseaeeneeeeeeees 21 5 1 Genera eege 21 5 2 Weathering and Drainage Requirement s sccccce
8. absorber is connected internally to small fluid carrying pipes through which the heat transfer fluid passes The collector usually has a transparent cover which allows solar energy to enter and helps reduce heat losses by convection An insulated enclosure provides structural integrity and reduces losses from conduction The solar collectors are connected to the domestic hot water DHW system and or the heating system in the dwelling by means of suitable pipe work which contains the heat transfer fluid Most commonly the heat transfer fluid used is a mixture of water and glycol anti freeze 3 2 Minimum specifications 3 2 1 Technical specifications Solar heating collectors should be fully tested and independently certified to l S EN 12975 1 and LS EN 12975 2 which specify requirements and test methods for solar collectors Solar heating systems should be fully tested and independently certified to comply with l S EN 12976 1 l S EN 12976 2 l S ENV 12977 1 ILS ENV 12977 2 and LS ENV 12977 3 as appropriate DoEHLG SEAI publication Heating and domestic hot water systems for dwellings Achieving compliance with Part L Building Regulations The solar collectors listed on the SEAI registered product lists have been tested in accordance with EN 12975 1 and EN 12975 2 and are assumed to be proper materials for the purpose of Part L of the Building Regulations see Section 1 2 6 of Building Regulations TGD L 2007 Th
9. correct operation of these systems during normal operation and after periods of non use For further guidance refer to National Guidelines for the Control of Legionellosis in Ireland HPSC 2009 and The Management of Legionnaires Disease in Ireland NDSC 2002 Cold and hot water pipe work should be as short as practicable especially where it only serves infrequently used taps and fittings In all cases minimum hot and maximum cold water temperatures should be reached at all draw off points after a maximum period of one minute running at full flow Due consideration should be given to the selection of braided or flexible hoses and the suitability of materials in contact with water Measures shall be taken in the design and installation of cold and hot water systems to prevent the colonization of the system with legionella These shall include the avoidance of stagnation of water in pipes cisterns and other storage vessels water temperatures in the range of 20 C to 45 C use of materials that can harbour or provide nutrient for bacteria and other organisms inside cisterns 3 3 5 Unvented hot water storage systems Where the solar heating system incorporates unvented hot water storage not exceeding 500 litres and 45kW power input additional safety requirements will apply As a minimum the unvented hot water storage system should be designed and installed by a person qualified to carry out such work be an appro
10. have a visible and In addition to the minimum collectors and hot durable label displaying all information required provision for labelling of hot water stores according to I S EN 12975 and including at least water storage vessels the following labelling with the following 1 name of manufacturer information 1 also recommended collector type Total net fluid content of secondary volume normally year of production heated by each heat ross area of collector exchanger where present g 1 0 litre serial number aperture area of collector The type fluid content maximum pressure and maximum operation pressure surface area of all heat exchangers net absorber area of collector 9 stagnation temperature at 1000 W m and 30 10 volume of heat transfer fluid 11 weight of empty solar collector 12 labelling of solar heated water storage vessels within solar domestic hot water systems b All hot water storage vessels should carry a label with the following information 1 2 manufacturer s name nominal overall capacity in litres standing heat loss in KWhi day type of vessel 5 auxiliary heating heat exchanger performance in kW where present C 30 pr SR 50 2 2010 E Table A 1 cont d Table 32 Minimum provisions for labelling commissioning and documentation for solar water heating systems 2 Commissioning A signed and dated commissioning
11. ie en TGD or purchased from Government Publications Sales Office Heating and Domestic Hot Water Systems for Dwellings Achieving compliance with Part L can be downloaded for free from DEHLG website www environ ie en TGD EST document CE 131 Solar water heating systems Guidance for professionals conventional indirect models can be downloaded for free from UK Energy Saving Trust website www energysavingtrust org uk business Business Resources Publications and Case Studies CIBSE document Solar heating Design and installation guide can be purchased online from CIBSE bookshop www cibse org index cfm go publications view amp item 376 BRE Digest 489 and 495 can be purchased online from BRE bookshop at www brebookshop com All I S standards can be purchased online at www standards ie All BS standards can be purchased online at http www bsi global com upload Standards 20 amp 20Publications shop html DEAP manual can be downloaded for free from www seai ie Your Building BER BER_Assessors Technical DEAP 29 pr SR 50 2 2010 E Annex A informative Extract of Table 32 DOEHLG SEAI publication Heating and domestic hot water systems for dwellings Achieving compliance with Part L 2008 Table A 1 Table 32 Minimum provisions for labelling commissioning and documentation for solar water heating systems Kaes Minimum provision Supplementary information 1 Labelling of solar a All solar collectors should
12. installations should be installed in or on roof constructions which have been designed in accordance with I S ICP 2 The solar collector installation should meet the requirements of clause 6 1 4 of S ICP 2 which states that solar collectors be designed as an abutment for top edges side and back gutter detail and the integrity of the underlay as a barrier to wind and water ingress should be maintained The principles used for the design of top edges side and back gutter details for abutments also apply to in roof collectors LS ICP 2 also gives the minimum head laps and fixing details for different types of slate and tile and includes maps for wind driven rain and wind speed 5 2 Weathering and Drainage Requirements The installation of a solar water heating system should not adversely affect the weather tightness or resistance to moisture penetration of the roof structure The integrity and durability of the roof envelope should be maintained Where solar collectors are installed integrated with the roof they should be tested assessed to determine resistance to wind driven rain Relevant test methods include BS 6375 Where proprietary flashings are used with the solar collector they both need to be weather tested to BS 6375 and prEN 15601 Adequate provision should be made for drainage of the collector and the diversion of drainage from the affected roof surface without compromising the integrity of the roof envelope Flashings sh
13. of the technology areas they wish to work in SEAI in conjunction with the Renewable Energy Installer Academy REIA has developed training courses for each technology and these courses are FETAC accredited A risk assessment should be prepared before work starts to identify and show how the risks identified will be controlled Section 7 2 gives details on the potential risks that must be covered by a risk assessment Safety requirements particular to elements of the system are given in product specific standards e g EN 12976 1 EN 12976 2 EN 12977 1 EN 12977 2 and EN 12977 3 All construction work related to the installation of solar collectors into or onto the building fabric should be performed to Safety Health and Welfare Construction at Work Regulations Specialised access equipment including eaves level platforms steel scaffold or towers cranes or hoists may be required during installation Recommendations for a pre installation risk analysis are provided in Section 7 2 which can be expanded upon relevant to the specific site installation All electrical work must be in accordance with ETCI regulations and carried out by persons suitably qualified to carry out such work A non switchable fused spur with LED should be used for the system Operation and safety of auxiliary heating systems should not be compromised and should be in accordance with relevant standards All pipework should be clearly marked in accordance with BS 1710
14. times the volume of the remainder of the cylinder Vp Further guidance is available in Appendix H of the DEAP manual The dedicated solar pre heat storage volume should be at least the greater of The anticipated average daily DHW demand or 35 litres m of absorber area Where the dedicated pre heat solar storage is combined into a DHW store combined store the volume shall be measured below the bottom of the lowest back up element electric immersion or heat exchanger coil down to the lowest element of the solar primary The heat loss in high performance cylinders should be less than 1 28 x 0 2 0 051 V2 3 kWh day where V is volume in litres which equates to a loss of 3 18 kWh day for 300 litre storage For a solar tank of 200 250 litres good practice for standing loss is 0 5 W per litre The total number of kWh required per year for hot water is now known from Point 1 above The collector area required to meet the chosen solar fraction Point 2 can then be calculated using the kWh m a yield obtained in Point 3 above 39
15. 1 x 2 16 x 4 7 x 1 0 1037 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1037 N 480 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 961 Pa would meet these loading requirements NOTE A solar collector installed on a site in Zone Il located within 0 1 km of the coastline and with a height above sea level of 200 m should be designed to withstand an uplift force of 770 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 1541 Pa Zone Ill Example The site is in Millstreet Co Cork Zone III in Figure B1 42 km from coastline 36 pr SR 50 2 2010 E The solar collector location array size and building ridge height and roof pitch are as Example 1 Site altitude is 123 m above mean sea level F Cp Qp Ze Arer D S Qp Ze 1172 Pa calculated per I S EN 1991 1 4 Cpt 0 11 from BS 5534 Table 6 Ae 18m x 1 2 m 2 16 m D 4 7 default value in BS 5534 Table 7 where no test data available S 1 0 value in BS 5534 Table 8 for no counter battens F 1172 x 0 11 x 2 16 x 4 7 x 1 0 1309 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1309 N 606 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 1212 Pa would meet these loading requirements NOTE A solar collector installed on a sit
16. 4 x 929 x 2 38 884 N downwards acting Fside rear 1 0 x 0 5 x 929 x 2 38 1106 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1106 N 465 Pa and a downwards acting force of 884 N 372 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 929 Pa and a positive pressure of 557 Pa would meet these loading requirements NOTE A solar collector installed on a site in Zone Il located within 0 1 km of the coastline and with a height above sea level of 200 m should be designed to withstand an uplift force of 745 Pa and a downwards acting force of 596 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 1490 Pa and a positive pressure of 894 Pa Zone Ill Example 34 pr SR 50 2 2010 E The site is in Millstreet Co Cork Zone III in Figure B1 42 km from coastline The solar collector mounting height array size and building ridge height and roof pitch are as Example 1 Site altitude is 123 m above mean sea level F CcCq Cf Qp Ze Aref Qp Ze 1172 Pa calculated per I S EN 1991 1 4 c 0 2 and 0 4 for wind blowing to front of collector from Table 7 4a I S EN 1991 1 4 0 5 for wind blowing from either side or the rear of collector from Table 7 4b I S EN 1991 1 4 CsCa 1 0 Aref 1 4m x 1 7 m 2 38 m Frront 1 0 x 0 2 x 1172 x 2 38 558 N upwards acting Ffro
17. CTOR CONNECTION TO EXPANSION VESSEL NOTE Fitting the expansion vessel in the orientation above is considered best practice for solar heating systems Figure 1 Example of a solar heating system schematic Flat plate collector pr SR 50 2 2010 E 2 Normative references The documents listed below contain provisions which through reference in this text constitute provisions of this document For undated references the latest edition of the cited publication applies together with any amendments Irish Building Regulations and Technical Guidance Documents Parts A to M Heating and Domestic Hot Water Systems for Dwellings Achieving compliance with Part L 2008 Section 9 Solar Water Heating Safety Health and Welfare at Work Construction Regulations Electro Technical Council of Ireland ETCI publication ET 207 Guide to the National Rules for Electrical Installations as Applicable to Domestic Installations SEAI Dwelling Energy Assessment Procedure DEAP Manual EST document CE131 Solar water heating systems Guidance for professionals conventional indirect models CIBSE document Solar heating Design and installation guide National Guidelines for the Control of Legionellosis in Ireland HPSC 2009 The Management of Legionnaire s Disease in Ireland NDSC 2002 BRE Digest 489 Windloads on roof based photovoltaic systems BRE Digest 495 Mechanical installation of roof mounted photovoltaic syste
18. NDERNEATH THE COLLECTOR Nic e RAFTERS K d w UV pe N Lt IN LINE BOTTOM FIXING DETAIL N Z N IN LINE SIDE FIXING DETAIL Ag Figure 2 Vertical and horizontal cross section of a solar collector installed in an inclined roof 19 pr SR 50 2 2010 E PENETRATION THROUGH ROOF COVERING i e BY PIPE lt WORK SHOULD BE WEATHER TIGHT USING A PROVEN lt AND DURABLE METHOD EXAMPLE SHOWN HAS d x 3 INSULATED SOLAR PIPE WORK PASSING THROUGH A PROPRIETARY SLATE TILE AND A TOP HAT TYPE SEAL WHERE PENETRATING ROOF UNDERLAY PROPRIETARY SLATE TILE VENT MAY PROVIDE AN ACCESS POINT FOR SOLAR PIPEWORK g Yj gt WHERE PROVENT TO MAINTAIN WEATHER RESISTANCE AT PENETRATION Uy SE e AN SG RE Q SB Vom SH AUXILIARY RAFTERS SPREADER BOARD AND SIDE SS BRACKETS TO RAFTERS SHOULD BE DESIGNED gt AND SPECIFIED BY AN ENGINEER PENETRATIONS THROUGH ROOF Ny Gs STAINLESS STEEL STRAPS BRACKETS AND FIXINGS UNDERLAY Le BY PIPE WORK lt lt INCLUDING ISOLATING GASKETS SHOULD BE SHOULD BE SEALED BY PROVEN AND SPECIFIED AND FIXED DIRECTLY TO THE ROOF DURABLE METHODS SUCH AS A TOP D STRUCTURE RAFTERS TRUSSES DESIGNED TO e mo eee lt gt ACCOMMODATE THE SOLAR COLLECTOR berate gt SB INSTALLATION SURFACE MOUNTED FIXING DETAIL Figure 3 Solar collector mounted in an inclined roof on top of the roof tiles 20 pr SR 50 2 2010 E 5 Solar collectors Design details and workmanship 5 1 General Solar collector
19. area is less than 20m and the solar heated water storage is less than or equal to 1000 litres This document gives guidance on Design installation commissioning and workmanship requirements for solar collectors and their associated fittings and accessories Structural constructional and weathertightness aspects of the solar collector installation including resistance to rain wind frost fire resistance and durability Use of solar water heating systems incorporating vented and unvented water storage Environmental and health and safety issues Solar collectors covered by this document include flat plate collectors and evacuated tube collectors either integrated into the roof structure or fitted on the roof pr SR 50 2 2010 E The solar collectors listed on the SEAI registered product lists have been tested in accordance with EN 12975 1 and EN 12975 2 and are assumed to be proper materials for the purposes of Part L of the Building Regulations see Section 1 2 6 of Building Regulations Technical Guidance Document TGD L Guidance on the assessment of solar heating systems against the requirements of Part L of the Building Regulations is given in DoEHLG SEAI publication Heating and domestic hot water systems for dwellings Achieving compliance with Part L 2008 and Appendix H of the DEAP manual Guidance on the mechanical and plumbing design and installation of solar heating systems is given in EST document CE131 Solar water hea
20. ature sensors one at the collector one at the top of the cylinder and one at the bottom of the cylinder It is important that key system functions can be monitored to determine potential performance losses or problems The DTC for the solar hot water system should be located in a prominent location that is readily accessible and frequently occupied Recommended location for the DTC is on the landing outside the solar store generally fixed not less than 1 5 m above floor level The DTC and function display should be readily visible at all times with clear access and not concealed or obstructed Where the DTC is located inside the solar store it must be fitted with an audible alarm Where the auxiliary heat controls allow particularly for electric immersions an immersion timer with LED switch should be sited beside the DTC Their location as described above will encourage monitoring of the solar system temperatures and enable prompt control of the auxiliary heating by manual or timed cycle s This should contribute to the efficient and safe use of the system Using a DTC it is possible to modulate pump speed in relation to temperature and minimise parasitic losses The DTC interlock should allow precise adjustments of pump switching on off points providing a readout to aid commissioning and fault detection A temperature interlock should ensure that the solar system cannot normally transfer useful heat outside the insulated building envelope
21. blockage due to debris and allow any moisture to freely discharge at eaves In the case of multiple collectors design should include for the increased volume of water to prevent backing up of water over the head of the flashing or over the sides 21 pr SR 50 2 2010 E 5 3 High Temperature Conditions Modern solar heating systems should be designed and installed to automatically and safely resume normal operation after an excess temperature event as specified in clause 4 1 1 of I S EN 12976 as follows no release of any high temperature fluid vapour or liquid under any operating conditions auto resumption of normal operation after stagnation without end user intervention As stagnation temperatures can be in excess of 150 C all materials in contact with or adjacent to pipe work must be protected or be able to resist such high temperatures The installer should accommodate methods of controlling stagnation in properties that do not have a frequent hot water load i e holiday homes etc Solar energy can quickly generate enough heat in a high performance collector to convert the circulating liquid to steam under significant pressure Since the worst case scenarios inevitably generate steam primary solar heating systems should be designed for steam handling from the outset Adequate provision should be made where necessary to protect the roof underlay from high temperatures by insulation or separation Lagging of pipework shoul
22. certificate should be completed to confirm the equipment has been correctly installed and to record key safety and operational features b As a minimum the commissioning certificate shall record the following details of a solar system 1 net aperture of solar collector minimum ambient temperature without freeze damage to components location and method of controlling overpressure location of electrical isolating switch type of circulation fluid circulation rate of collector unit location of device for protection of overheating solar heated water 3 Documentation No minimum requirement Information concerning the solar domestic hot water system should be provided to the dwelling owner and or end user as applicable The documentation should include user s manual warranty information a recommended maintenance schedule commissioning certificate full contact details of installer guidance re control of bacterial growth legionella 31 pr SR 50 2 2010 E Annex B informative Sample wind load calculation for solar collectors The sample calculations in this Appendix are based on LG EN 1991 1 4 and BRE Digest 489 and are for illustrative purposes only Architects and specifiers should satisfy themselves that a particular solar collector is suitable for the proposed installation location B 1 Determining the Design Wind Load BRE Digest 489 gives the following general equations for win
23. ctions insulation roofing felt etc have been designed or selected to function for the expected temperature range over the design life Any exposed insulation should be resistant to high temperatures UV degradation and be non water absorbent closed cell Verification of satisfactory performance of the above criteria can be achieved by NSAI Agr ment certification or equivalent as defined in Part D of the Building Regulations Guidance for materials used in hot water systems is given in I S SR 50 Approved fluids specified by the manufacturer should contain anti corrosion inhibitors and anti freeze Motor vehicle anti freeze should not be used All waste antifreeze and corrosion inhibitors should be collected and disposed of in accordance with national and local regulations and material safety data sheets 15 pr SR 50 2 2010 E 4 Solar collectors Requirements 4 1 Positioning of collectors for maximum solar efficiency The angle and orientation of the solar collectors will determine their efficiency This combined with anticipated household occupancy use will determine the number of panels or evacuated tubes required Table 1 shows the annual solar radiation obtained at various orientations and angles to the horizontal For optimum efficiency the collector should be sited on a pitched roof of between 30 to 45 with a south or SE SW orientation The solar collector should be located so as to minimise shading Table 1
24. d be continuous to the solar collector especially through roof and underlay penetrations Typically rated motor valves and fittings should be located on the cooler return line with one way check valves to prevent reverse flow It is very important to match pump power to the minimum required for circulation using variable speed inverter driven pumps Because of the risk of scalding or over pressure the system must be capable of hydraulic and electrical isolation from any pump and pre heat storage to allow for periodic maintenance Ball or gate valves for isolation must not be able to accidentally isolate the collector from a route to a safety device especially to isolate a safety pressure release valve or expansion drainback vessel The thermal hot water store should be approved by the solar manufacturer for use with the solar collector and approval should cover safety durability and reliability when solar pre heated The solar primary system should include an indicator of primary circuit transmission levels flow limiter gauge is shown in Figure 1 Correct system function indicators are essential to determine pre empt reductions in efficiency and potential safety issues as faults in systems can go unnoticed auxiliary heat source could compensate for a solar system fault Flow rate set at commissioning should be recorded on the commissioning maintenance log 22 pr SR 50 2 2010 E 6 Solar collectors Design life The installat
25. d load used in the design of roof mounted and in roof solar heating systems NOTE Roof Mounted where CsCa Cf Oe Ze Aref Symbols from BRE Digest 489 have been amended to match those in S EN 1991 1 4 F CsCa Cf Qp Ze Aref is the structural factor from LG EN 1991 1 4 CsC may be taken as 1 0 for building height less than 15 m is the force coefficient for the structure is the peak velocity pressure at reference height Ze Unless otherwise defined can normally be safely taken as the maxium height of the roof the height to the ridge on which the collector is attached is the reference area of the structure or structural element For overall loads on individual collectors Aref will be the area of the collector exposed to the wind If the roof mounted collector is supported by for example four hooks each hook its fixings and the supporting roof structure should be designed to resist a quarter of the wind force In Roof 32 F Cpt qp Ze Arer D S where R Oe Ze Aref is the appropriate pressure difference coefficient for the system under consideration is the peak velocity pressure at reference height Ze Unless otherwise defined can normally be safely taken as the maxium height of the roof the height to the ridge on which the collector is attached is the reference area of the structure or structural element For overall loads on individual collectors Aref
26. dered within the store reflecting the potential risks Solar heating system pipe work and components may reach temperatures in excess of 150 C under full stagnation conditions Consideration should be given to the routes taken by the primary solar pipe work to restricting occupant contact identification markings and associated risks to adjacent materials or those in direct contact 3 3 8 Differential thermostatic control Solar heating systems should have a Differential Thermostatic Control DTC or similar device that can automatically check for errors incorrect value readings and give a clear warning of malfunction Simple counters of time volume power or energy alone are not sufficient for warning of malfunction 13 pr SR 50 2 2010 E An automatic audible or flashing light warning device to indicate critical malfunction is recommended that should also allow rapid diagnosis of error Predetermined system checks selected by a commissioning person qualified to carry out such work are programmed into the differential pump controller or similar device These checks are typically based on temperature but pressure and or circulation rates could also be used to trigger an error indicator The solar heating system controls should have the capability to provide an accurate readout of the temperatures of the absorber solar pre heat store and auxiliary domestic hot water DHW store This will typically require the provision of 3 no temper
27. e in Zone III located within 0 1 km of the coastline and with a height above sea level of 250 m should be designed to withstand an uplift force of 905 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 1810 Pa Zone IV Example The site is in Ballintra Aran Island Zone IV in Figure B1 2 km from coastline The solar collector mounting height array size and building ridge height and roof pitch are as Example 1 Site altitude is 209 m above mean sea level F Cf Qp Ze Aret D S Qp Ze 1640 Pa calculated per I S EN 1991 1 4 Cpt 0 11 from BS 5534 Table 6 Aref 1 8 mx 1 2 m 2 16 m D 4 7 default value in BS 5534 Table 7 where no test data available S 1 0 value in BS 5534 Table 8 for no counter battens F 1640 x 0 11 x 2 16 x 4 7 x 1 0 1831 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1831 N 848 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 1696 Pa would meet these loading requirements NOTE A solar collector installed on a site in Zone IV located within 0 1 km of the coastline and with a height above sea level of 250 m should be designed to withstand an uplift force of 1048 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 2097 Pa 37 pr SR 50 2 2010 E Annex C informative Sizing of solar co
28. e must also be completed before work commences The following points should be considered shading Where shading exists its effects should be brought to the attention of the homeowner and options for alternative collector positions or shading object removal should be discussed collector fixing surface The collector must be fixed to a pitched roof that has roof underlay and battens in place in accordance with I S ICP 2 roof orientation For optimum performance the collector should be fitted on a south facing roof see Table 1 The impact which collector positioning has on solar collector performance should be explained to the homeowner access to collector location pre heat storage location The solar pre heat store must be located where it can readily connect with the solar connector via insulated primary pipes and sensor cables secondary water pressures water quality Water quality hardness acidity bacteria levels must be assessed for each site before selecting secondary heating equipment Where water temperatures are above 60 C scale formation tends to accelerate rapidly configuration of occupants DHW system and anticipated usage patterns solar collectors sized for dwelling based on irradiation levels relative to roof pitch orientation contained in Table 1 and household size location of pump station assembly including access and clearance from cylinders shelving and similar
29. eccsseeeeeeeeeeeeeeseeeseseeeenseeeeeeeeeseeseneeneneees 36 Annex C informative Sizing of solar collector and StOraQe ccseeccsseceseeeeeseeeeeeeeeseeeeeseeeeneeeeseeesensaneeeseees 38 pr SR 50 2 2010 E Introduction These guidelines have been established to elaborate on the requirements for solar water heating systems not directly addressed by Part L of the Building Regulations The guidelines are intended to assist providers and specifiers of solar water heating systems in the interpretation of the requirements and to provide guidance as to how the requirements should be addressed This document has been developed by a working group of representatives from NSAI Agr ment Department of Environment Heritage and Local Government DOEHLG Sustainable Energy Authority of Ireland SEAI Emphasis is on general principles and not on detailed aspects of particular systems As the construction industry becomes more familiar with all aspects of solar heating systems technical issues may arise requiring the document to be reviewed 1 Scope This document gives general guidelines for design installation and commissioning of solar heating systems in single dwellings where The solar heating system is incorporated into and the solar collector is an integrated or stand alone element of the external building envelope The solar heating system is designed as the primary or auxiliary water heating system The solar collector
30. ems General requirements LS EN 12976 2 Thermal solar systems and components Factory made systems Test methods LS ENV 12977 1 Thermal solar systems and components Custom Built systems Part 1 General requirements LS ENV 12977 2 Thermal solar systems and components Custom built systems Part 2 Test methods LS ENV 12977 3 Thermal solar systems and components Custom built systems Part 3 Performance characterization of stores for solar heating systems LS EN 12897 Water supply Specification for indirectly heated unvented closed storage water heaters LS EN 14336 Heating systems in buildings Installation and commissioning of water based heating systems LS EN 14437 Determination of the uplift resistance of installed clay or concrete tiles for roofing Roof system test method LS EN 60730 2 11 Automatic electrical controls for household and similar use Particular requirements for energy regulators LS EN 62305 Protection against lightning LS EN ISO 9488 Solar energy Vocabulary prEN 15601 Hygrothermal performance of buildings Resistance to wind driven rain of roof coverings with discontinuously laid small elements Test method ISO 9553 Solar energy Methods of testing preformed rubber seals and sealing compounds used in collectors ISO TR 10217 Solar energy water heating systems guide BS 476 3 Fire tests on building materials and structures Classification and method of te
31. ents a refractor test should be undertaken which will indicate the level of frost protection to the primary circuit fluid the solar controller should be checked to ensure it has the same operating parameters as on the commissioning date Maintenance details should be recorded onto the maintenance log which can be fixed to the pump station or solar cylinder The date for next maintenance should also be recorded 8 3 User Manual After commissioning a user manual should be given to the homeowner as described in Section 9 Table 32 of DoEHLG SEAI document Heating and domestic hot water systems for dwellings Achieving compliance with Part L Information that should also be included in the user manual is described in Section 5 of EST document CE131 The user manual shall contain sufficient information about the system all component parts and their maintenance requirements so that the building can be operated safely in such a manner as to use no more fuel and energy than is reasonable under the circumstances As a minimum it should include a recommended maintenance schedule commissioning certificate full contact details of installer and guidance on use in clear and easy to understand language and format 28 pr SR 50 2 2010 E 9 Locating Reference Material Building Regulations and Technical Guidance Documents can be downloaded for free from Department of Environment Heritage and Local Government DEHLG website www environ
32. ids live loads wind loads thermal stresses due to expansion contraction combinations of the above minimise wind loads on the collector a minimum distance of 0 5 m should be kept between the collector and the ridge and eaves The following specific criteria must be met a The roof structure and any modifications necessary to accommodate the collector and system components should be designed checked by a suitably qualified engineer against the requirements of the Building Regulations taking into account the direction magnitudes and lines of actions of forces applied to the collector the height the collector projects above the roof level and its plan location on the roof The design should address the structural adequacy and durability of the roof structure the fixing substrate including its fixings metal brackets rails or similar and their associate fixings both to the collector and structural substrate The design should address the structural adequacy and durability of the roof structure the fixing substrate including its fixings metal brackets rails or similar and their associated fixings both to the collector and structural substrate Any holes or notches in structural members should not compromise structural integrity Design loads should be established in accordance with Building Regulations TGD A 1 dead loads should be calculated in accordance with I S EN 1991 1 1 2 minimum imposed roof loads should be calcu
33. ion of a solar heating system should not compromise the design life of the building and in particular the design life of the roof envelope Solar heating systems should be assessed for durability in accordance with LG EN 12975 1 I S EN 12976 and l S ENV 12977 as appropriate In addition it is recommended that the durability of the solar collector be assessed as a building element Durability of the collector should be stated by the manufacturer It is recommended that a collector which can easily be replaced e g offset above the roof should have a design life comparable with that of other building services and require a minimum of maintenance The roof covering beneath the collector maintains the integrity and durability of the roof in this case Otherwise the design life should be equivalent to that of the building envelope as specified in clause 5 11 1 of I S ICP 2 assuming normal maintenance i e a design life in the order of 60 years BS 7543 can be referred to for durability This would typically relate to roof integrated solar collectors not easily replaced without significant works All permanent structural fixings brackets and flashings should have a design life equivalent to that of the building envelope and should require no maintenance over that period 23 pr SR 50 2 2010 E 7 Installation 7 1 General The design installation and commissioning of solar thermal installations and peripheral components should be car
34. ion risks This can be achieved by briefly heating the store beyond 60 C pipes should only be insulated after final pressure testing except for pre tested and continuous unbroken pipe work runs used without joints or fittings hot water cylinder heat exchangers and expansion vessel taking into account its suitability for high temperature should be sized and approved for use with the solar hot water system See Appendix C pr SR 50 2 2010 E 8 Commissioning and Maintenance 8 1 Commissioning Once installation has been completed the installed system must be commissioned Commissioning must be carried out by a person qualified to carry out such work The solar installation should be commissioned so that at completion the system and associated controls are left in the intended working order and can operate efficiently for the purposes of the conservation of fuel and power The procedure for commissioning of these systems is set out in DoEHLG SEAI document Heating and domestic hot water systems for dwellings Achieving compliance with Part L They should as a minimum cover the following confirmation that the system is properly commissioned and tested for correct operation commissioning certificates signed and dated confirm equipment is correctly installed commissioning checklist Record key safety and operational features such as location and method of controlling over pressure location of electrical isola
35. ipework should be bonded in order to avoid electrical potential differences The flow and return pipes to the solar collector should be fitted with earth clamps connected to the earthing system of the house using an earth bonding cable of minimum 10 mm A diode for over voltage protection should also be provided to the control panel to limit potential damage from lightning 3 4 Materials Materials should comply with Building Regulations TGD D 14 pr SR 50 2 2010 E The temperatures and pressures experienced by some components may be significantly in excess of normal domestic operating temperatures 150 C and greater In addition consideration should be given to roofing materials in contact with such components All materials and components should be durable for the required design life be capable of withstanding the thermally induced structural impact and environmental stresses imposed during the design life have adequate resistance to wind rain impact heat aging air pollutants high humidity steam UV exposure and corrosion including internal ozone salt spray rodent attack heat transfer fluid especially when in contact with dissimilar metals have adequate resistance to fire Guidance for specification of roofing materials is given in I S ICP 2 Particular care should be taken to ensure that solar collector components or roofing materials subject to extreme temperatures pipe work welded conne
36. ird party certification bodies e g NSAI Agr ment are available to assess compliance with all parts of the Building Regulations It is recommended that solar collectors should carry the Solar Key Mark 3 2 2 Minimum provisions for labelling commissioning and documentation Provisions for the solar collector and hot water store should be in accordance with Section 9 Table 32 of DoEHLG SEAI publication Heating and domestic hot water systems for dwellings Achieving compliance with Part L see Appendix A 3 3 Safety Considerations 3 3 1 General The solar heating system should be designed installed and commissioned to ensure the levels of risk associated with all aspects of the solar collector installation and operation are acceptable Guidance on addressing the safety requirements associated with mechanical installation operation and maintenance of the system is given in EST document CE131 and CIBSE document Solar heating Design and installation guide 10 pr SR 50 2 2010 E All aspects of the work should be carried out by persons qualified to carry out such work to ensure the appropriate levels of safety are achieved The design installation and commissioning of solar thermal installations should be carried out by a person qualified to carry out such work in accordance with clause 1 2 7 of the Building Regulations TGD L A suitably qualified installer must have achieved certification from an accredited training course in each
37. lated in accordance with I S EN 1991 1 3 using the snow load map given in Building Regulations TGD A Table 14 3 wind loads should be calculated in accordance with I S EN 1991 1 4 LS EN 12975 1 requires that the solar collector withstand minimum positive and negative pressures of 1000 Pa The standard states a safety factor of 2 should be applied for negative pressure which means that a pass at 1000 Pa equates to a permissible negative pressure uplift of 500 Pa The standard also states a safety factor of 1 5 should be applied for positive pressure which means that a pass at 1000 Pa equates to a permissible positive pressure of 667 Pa Designers and installers of solar collectors should satisfy themselves that the installed product and fixings at the installed location are capable of resisting the positive and negative wind pressures for their design life based on wind load calculations to LS EN 1991 1 4 as stated in b above Alternative design approaches may be achieved by referring to BRE Digest 489 Wind loads on roof based photovoltaic systems for further guidance Appendix B shows sample wind load calculations The collector support system must be designed and constructed to comply with the relevant technical specifications for structural use of timber e g l S EN 1995 1 1 Solar collector loading may cause roof truss members designed for tension to go into compression and vice versa this should be addressed by design 17 p
38. llector and storage Calculate the water heating requirement for a dwelling Typical domestic hot water DHW consumption can be from 30 to 50 litres per day per person System losses should be included in the total DHW demand DEAP provides for DHW consumption based on number of occupants and floor area The Total Hot Water Demand can be taken from the Water Heating tab in DEAP The proportion of energy to be provided from the solar heating system should be provided This is the energy from the solar system used to heat the water in the thermal store divided by the total system load Typical solar fractions vary between 35 and 60 at 60 C Solar Fraction Annual solar energy x 100 Total heat required for DHW Total heat required for DHW Annual solar energy delivered to DHW storage Back up DHW energy delivered to DHW storage A solar fraction can be specified for an individual month e g in July the designer could select 90 solar fraction at 60 C Therefore the rest of the year would have less solar fraction in each month The average solar fraction for the rest of the year would equate to approximately 55 where 90 is selected for the summer Attempting to increase the solar fraction beyond 60 or for the summer months up to 100 can result in excess heat being generated during peak sunny days requiring consideration of the system layout to withstand stagnation temperatures and potential overheating in the store The solar o
39. ms LS S R 50 Code of practice for plumbing and heating currently being drafted l S ICP 2 Code of practice for slating and tiling LS 193 Timber trusses for roofs LS 444 The use of structural timber in buildings LS EN 485 1 Aluminium and aluminium alloys Sheet strip and plate Technical conditions for inspection and delivery l S EN 516 Prefabricated accessories for roofing Installations of roof access Walkways treads and steps l S EN 517 Prefabricated accessories for roofing Roof safety hooks LS EN 795 Protection against falls from a height Anchorage devices Requirements and testing LS EN 837 1 Pressure gauges Bourdon tube pressure gauges Dimensions metrology requirements and testing LS EN 1490 Building valves Combined temperature and pressure relief valves Tests and requirements LS EN 1991 1 1 Eurocode 1 Actions on structures General actions Densities self weight imposed loads for buildings LG EN 1991 1 4 Eurocode 1 Actions on structures General actions Wind actions pr SR 50 2 2010 E LS EN 1995 1 1 Eurocode 5 Design of timber structures General Common rules and rules for buildings LS EN 12975 1 Thermal solar systems and components Solar collectors General requirements LS EN 12975 2 Thermal solar systems and components Solar collectors Test methods LS EN 12976 1 Thermal solar systems and components Factory made syst
40. nt 1 0 x 0 4 x 1172 x 2 38 1116 N downwards acting Fside ear 1 0 x 0 5 x 1172 x 2 38 1395 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1395 N 586 Pa and a downwards acting force of 1116 N 469 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 1172 Pa and a positive pressure of 703 Pa would meet these loading requirements NOTE A solar collector installed on a site in Zone III located within 0 1 km of the coastline and with a height above sea level of 250 m should be designed to withstand an uplift force of 875 Pa and a downwards acting force of 700 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 1750 Pa and a positive pressure of 1050 Pa Zone IV Example The site is in Ballintra Aran Island Zone IV in Figure B1 2 km from coastline The solar collector mounting height array size and building ridge height and roof pitch are as Example 1 Site altitude is 209 m above mean sea level F C Ca Cf Qp Ze Aref Qp Ze 1640 Pa calculated per LS EN 1991 1 4 Cf 0 2 and 0 4 for wind blowing to front of collector from Table 7 4a I S EN 1991 1 4 0 5 for wind blowing from either side or the rear of collector from Table 7 4b I S EN 1991 1 4 CsCqg 1 0 Ae 1 4 mx 1 7 m 2 38 m Ffront 1 0 x 0 2 x 1640 x 2 38 781 N upwards acting 35 pr SR 50 2 2010 E F
41. or using fixing brackets that are all checked by a suitably qualified engineer Further guidance on designing for wind load can be found in BRE Digest 489 Wind loads on roof based photovoltaic systems and CIBSE document Solar heating Design and installation guide In the case of solar collectors installed above the roof tiles slates brackets and rails must be used The fixing system must be strong and stiff enough to resist wind loads and uplift forces The fixing of each bracket to the rafter should have a minimum of two screws or coach bolts to ensure rigidity If fixing is to the top of the rafter where infill roof trusses are present care must be taken to ensure that the minimum width is not less than 35 mm Where this occurs one of the following methods should be used 1 fix an auxiliary rafter of 38 mm width to the side of the roof truss with length and fixings specified or 2 use a bracket that is fixed and can be structurally supported by the side of the roof truss Check truss design for point loads and suitability for such an application Any such modifications work should be part of the structural design check The fixings for the offset system should not allow the roof covering to be lifted where rainwater penetration could occur Some fixings may raise laps in the roof covering by more than 5mm depending on thickness and profile Where this is pronounced the fixing method should be independently weather tested and certified to
42. ould take surface water from slates tiles or any discharge above the solar collector the sides of the collector and between collectors discharging onto the roof covering below Drainage channels provided typically to the proprietary flashing should have adequate hydraulic capacity It is recommended that this is best achieved by a double drainage channel system to the sides with flashing designed to prevent overflow into roof space be vermin and UV resistant and incorporate foam strip in the inner channel The profile should be designed to suit the roof type i e slate or tile Flashings should have rigidity in profile dressed tight to the roof covering without the risk of uplift or water ingress Where possible solar pipe work should run beneath the proprietary flashing and be taken into the roof space underneath the head flashing avoiding the need for additional works or weathering of the roof covering Care must be taken to protect materials and underlay from the high temperatures associated with the solar components Where the underlay is penetrated e g due to fitting of support brackets for the solar heating system or pipe penetrations the penetration must be sealed using appropriate proven and durable methods resistant to high temperatures Typical methods include grommets or top hat seals The void between the roof covering including solar collector flashings etc and the roof underlay should be designed so as to minimise risk of
43. priate package which satisfies the requirements of the Building Regulations Part D and has third party certification to EN 12897 12 pr SR 50 2 2010 E be provided with a minimum of two temperature activated safety devices capable of preventing the temperature of stored water reaching 100 C at any time on direct and indirect systems Le anon self resetting thermal cut out to EN 1490 one or more temperature relief valves to BS 6283 2 NOTE Other safety devices should provide an equivalent degree of safety in preventing temperature of stored water exceeding 100 C have temperature relief valves located directly on the storage vessel sized to give a discharge rating measured in accordance with BS 6283 2 Appendix F or BS 6283 3 Appendix G at least equal to the power input to the water Each valve should discharge via a short length of metal pipe not less than the outlet size of the relief valve to a manifold sized to accept total discharge via a vertical metal tun dish to provide an air break sited as close as possible to the relief valve maximum 500 mm for indirect heating systems a non self resetting thermal cut out should be fitted This should be wired up to a motorised valve or other suitable device to shut off the flow to the primary heater and be approved as referenced above ensure hot water is discharged from safety devices and conveyed in pipe work to where it is visible but causes no dange
44. r SR 50 2 2010 E 18 For above roof installations the roof covering beneath should be mechanically fixed In general collectors should not be placed within 0 5m of the edge of the roof or projections such as parapets chimneys or dormer windows Roofs with valleys will also require particular attention for the safe installation of collectors and roof covering Fixings must comply with the requirements of Section 3 4 of this document and clauses 4 11 and 5 9 of LS ICP 2 Specific advice on design life of fixings should be sought from the fixing manufacturer with relevant support documentation Where stainless steel fixings are used to secure the collector isolating gaskets should be provided where necessary to ensure that bi metallic corrosion does not occur Flashings must comply with the requirements of Section 3 4 of this document and Clause 4 12 of LS ICP 2 To minimise offset forces the fixing clips must fit tightly into and against the sides of the collector All tiles adjacent to solar collectors should be mechanically fixed in place in accordance with current practice for roof lights see l S ICP 2 Fixing methods for solar collectors vary but can typically require at least 4 mounting points with loading taken through and not onto the roof covering This should either be directly onto the rafters recommended approach or to additional structurally designed and adequately supported timber bearers not standard roof battens
45. r to persons in or around the building 3 3 6 Existing buildings A site visit is required in order to inspect roof voids the roof condition and clearances for equipment Externally the terrain should be checked for stability as well as above for loose roof tiles and overhead cables etc Heights over two storeys should be approached with particular caution Consideration should be given to the load bearing capacity of the cylinder and to the space required to house the solar cylinder pump station etc 3 3 7 Pressure relief valves Solar hot water system pressure relief valves should be routed to a vessel made of suitable material capable of withstanding the high temperature of the fluid so as to cause minimum damage and to prevent any safety risks Local authority approval should be sought if considering direct discharge to drainage system All safety control valves should be readily accessible and verifiable in operation particularly during commissioning and maintenance The requirement to store primary circulation fluid temporarily typically in hot water cylinder cupboard may occur for top up purposes or to facilitate a pressure discharge from the solar primary circuit Where this occurs the fluid should be safely stored e g at high level in a secure transparent locked container properly labelled resistant to high temperature discharge and access controlled to prevent unauthorised removal or use Safety signage should be consi
46. rature flow return be located so as to prevent or restrict occupant contact and not cause risk to materials adjacent to or in contact with pipe work The solar heating system may require the provision of an additional water storage tank in the attic In this case the roof should be designed to take the additional loading EQUALIZING SLAT INCLINED HEAD FLASHING DETAIL be BOARD PROTECTING PIPEWORK AND e raa PENETRATION THROUGH N E By Zeen d UNDERLAY QF tha GC EXISTING SZ iS Se ROOF Ss d Se RAFTERS f y Py am Ka NN Y PENETRATIONS THROUGH ROOF Se UNDERLAY Le BY PIPE WORK De SHOULD BE SEALED BY PROVEN ANO bw DURABLE METHOD SUCH AS A TOP HAT TYPE SEAL RESISTANT TO HIGH amp TEMPERATURES AND MOISTURE INGRESS TREATED TIMBER BEARERS Ze SR lt t DESIGNED AND SPECIFIED FOR Sy a JN ROOF INSTALLATION TO S PROVIDE SUPPORT A SY UNDERNEATH THE COLLECTOR We 4 IN LINE TOP FIXING DETAIL Ss MS Ng my ROOF TILES ON TIMBER BATTENS ON PROFILE SIDE FLASHINGS TO Ss SARKING FELT ON RAFTERS WITH EXTEND DOWN OVER BOTTOM DOUBLE CHANNEL FLASHING FLASHING FLASHING SHOULD BE TIGHT AND BOTTOM FLASHING MUST EXTENO UP hs UNDER SIDE FLASHINGS f HH y HH oe NS ONG _ LEAD APRON J COLLECTOR e ae H E E EE x u Se DESTING Na mn ng al TREATED TIMBER BEARERS i DESIGNED AND SPECIFIED FOR SA Deeg k OIT ROOF INSTALLATION TO KS Ka EXISTING PROVIDE SUPPORT oe FINN ROOF SARKING FELT U
47. rectly with mechanical protection trunking etc if at risk of physical impact Minimum clip spacing is 250 mm horizontal and 400 mm vertical all pipework should be adequately supported insulated high temperature resistant labelled for identification flow and return highlighted especially at cylinder and take shortest route possible from collector with continous slope back to pump station no PVC cable should be in contact with copper pipes External cables greater than 300 mm are to be supported All cables must be protected from sharp edges etc by purpose guides or grommets all cable conductors external of joint enclosures must be insulated and sheathed External cables must be UV stable before filling consideration of flushing to clean the system should be given according to BS 7593 and LS SR 50 The primary system should be flushed cold then hot until clear as unwanted particles and chemicals will get into components during pipe installation Care should be taken where there is a risk of freezing once the system has been shown to be leak free a prolonged pressure test should be carried out In systems where antifreeze is used it should be added prior to the initial pressure test as it reduces surface tension properties of the water and therefore searches out leaks that would otherwise not be detected during the test solar pre heat stores made from copper need to form an oxide layer on the interior surface to reduce corros
48. ried out by a person s qualified to carry out such work in accordance with clause 1 2 7 of the Building Regulations TGD L A suitably qualified installer must have achieved certification from an accredited training course in each of the technology areas they wish to work in SEAI in conjunction with the Renewable Energy Installer Academy REIA has developed training courses for each technology and these courses are FETAC accredited 7 2 Risk Assessment Before work commences on installation of a solar heating system a risk assessment must be completed to cover as a minimum the following risks 24 access to roof ability of roof structure to accommodate all applied loadings working at height lifting the weight and size of collectors to roof obstruction of wires cables and other services risk of bacterial growth in cold water stores old long or under heated pipe runs limescale formation wiring of different voltage classes effects of wind snow and fragility of glass on collectors and roof structures lead pipe dust and toxic materials steam production during initial filling and fault finding confined and conductive locations high temperature pipework and liquids glycol antifreeze storage or discharge release primary pipework routing water quality excessive pressures fire safety installation of high temperature components lightning earthing maintenance of the system pr SR 50 2 2010 E A survey of the sit
49. rront 1 0 x 0 4 x 1640 x 2 38 1561 N downwards acting Fside rear 1 0 x 0 5 x 1640 x 2 38 1953 N upwards acting The solar collector and its fixings should be designed to withstand an uplift force of 1952 N 820 Pa and a downwards acting force of 1561 N 656 Pa Any collector that has been tested under EN 12975 2 to a negative pressure of 1640 Pa and a positive pressure of 984 Pa would meet these loading requirements NOTE A solar collector installed on a site in Zone IV located within 0 1 km of the coastline and with a height above sea level of 250 m should be designed to withstand an uplift force of 1014 Pa and a downwards acting force of 811 Pa In this case a collector tested under EN 12975 2 would have to be tested to a negative pressure of 2028 Pa and a positive pressure of 1217 Pa B 3 Sample wind load calculations for in roof collector Zone II Example The site is in Navan Co Meath Zone II in Figure B1 30 km from coastline The solar collector is integrated into the roof in the central roof area The array size is 1 8 m x 1 2 m The building ridge height is 8 m Site altitude is 35 m above mean sea level Roof pitch is 30 F Ct Qp Ze Aret D S Qp Ze 929 Pa calculated per LS EN 1991 1 4 Cpt 0 11 from BS 5534 Table 6 Aref 1 8 mx 1 2 m 216 m D 4 7 default value in BS 5534 Table 7 where no test data available S 1 0 value in BS 5534 Table 8 for no counter battens F 929 x 0 1
50. seeeeeeeeeeneeeeeeeseeeeneeseeeesneesesesneeseeeseeseseseanseeeenes 21 5 3 High Temperature Conditions ccccccsseeeseceeeeeeeseeeseseeeeeeeeeescaeseneeeeeeeeeseaesesaeeseseeeseaesaseaeeneeseeseaeneas 22 6 Solar collectors Design life ees cles ee waste ce ceed eka cde Edge NEES See 23 7 MPVS TANNA ONT crs acai ce tate act Ma ese A EE e 24 7 1 Ge Mel EE 24 7 2 RSK ASSESS A eisereen Eege ege eeneg 24 7 3 Installation Ftrocedute eege aa cate Seu ege Seege Seeerei 25 8 Commissioning and Maintenance ccccseenceceeseeeeeeeseceeeeeseeeseseseeeeesescensesesceeseseecensesescenenseesenes 27 8 1 Eommlesioningd eege Ee Ee 27 8 2 Eu ET 27 8 3 User Ma u a E 28 9 Locating Reference Material cccccsceseeeeeeeeeeeeeeeeeeneeeeeee seen ease neeeeeee sees nnnnnnnn mnene nunnana nnmnnn nennen 29 Annex A informative Extract of Table 32 DoOEHLG SEAI publication Heating and domestic hot water systems for dwellings Achieving compliance with Part L 2008 eccsssseeneseeeerees 30 Annex B informative Sample wind load calculation for Solar COMeCCtOIS csseceseeeeeseeeseeeenseeeeeeees 32 B 1 Determining the Design Wind LOad csseceseceeeeeseeeeeeeeeeeeseaeeeseeeeneeeeseaeseseaeeeeseeeseaeseseaesaseeeeeeeeneas 32 B 2 Sample wind load calculations for roof mounted COMOCtON cssecceseceeeseesseeeenseeeeeeeeeeseeseneeneneees 33 B 3 Sample wind load calculations for in roOf COMCCTON cces
51. show compliance with the Building Regulations The collector must have the ability to absorb effects of building movement thermal stresses without damage to the integrity of the roof underlay fixings flashings etc On roof collectors should be stiff enough to resist wind loads which could cause slate or tile uplift The uplift resistance of the collector and fixings needs to be established to I S EN 14437 or equivalent The distance between the underside of the collectors installed above the slates or tiles and the roof surface should be designed and specified by the solar manufacturer for the particular roof type to minimise uplift forces prevent trapped debris or blockages to permit air circulation and adequate drainage and comply with the Building Regulations The system must have adequate resistance to frost in accordance with I S EN 12976 2 The risk of bi metallic corrosion should be avoided in accordance with clause 5 11 3 of I S ICP 2 pr SR 50 2 2010 E Where the collector is installed as part of the roof the provision for thermal insulation should if possible be the same standard as the surrounding construction In addition the roof construction and materials should be protected from exposure to excessive temperatures through contact with the collector components All pipe work should be insulated to protect from temperature extremes and to prevent condensation Also they should have identification markings high tempe
52. spection maintenance and or replacement the pump station assembly which houses the mechanical safety controls components and fittings should be clearly visible in the store be readily accessible and not concealed or obstructed by cylinders vessels shelving or similar a good practice layout should be made available with each solar hot water system showing position of components pump station cylinder expansion vessel etc and minimum clear space recommended on plan for all access requirements it may be necessary to provide a dedicated service room for the solar hot water system including pump station cylinder and related components consideration should be given to the load bearing capacity of the solar cylinder 3 3 4 Risk of bacterial growth legionella The solar heating system should be designed so as to prevent the risks associated with bacterial growth low water flow rates and scale formation whilst preventing risk of scalding due to high water temperatures In order to reduce the risk of colonization of a water system the temperature of cold water in pipes and cisterns should not exceed 20 C and hot water should be stored and distributed at a temperature of not less than 60 C with a temperature at the discharge point of 50 C after one minute Systems should be designed and operated to provide appropriate temperature control of water storage Information and guidance should be provided to the homeowner on the
53. st for external fire exposure to roofs BS 1494 1 Specification for fixing accessories for building purposes Fixings for sheet roof and wall coverings BS 1710 Identification of pipelines and services BS 5250 Code of practice for control of condensation in buildings BS 5534 Code of practice for slating and tiling including shingles BS 5918 Code of practice for solar heating systems for domestic hot water BS 6283 2 Safety and control devices for use in hot water systems Specifications for temperature relief valves for pressures from 1 bar to 10 bar pr SR 50 2 2010 E BS 6375 Performance of windows and doors Classification for weathertightness and guidance on selection and specification BS 7206 Specification for unvented hot water storage units and packages BS 7543 Guide to durability of buildings and building elements products and components pr SR 50 2 2010 E 3 Solar heating systems General requirements 3 1 General A solar heating system generates heat by means of solar collectors either flat plate or evacuated tubes which absorb solar radiation energy and converts it to thermal energy The part of a solar collector which converts the solar energy into thermal energy is called the absorber The absorber is usually in the form of a plate with a special layer coating where a high level of solar energy can be captured with low heat losses due to emission of the resulting heat energy from the absorber The
54. ting switch type of circulation fluid and location of device for protection of overheating solar heated water An example of a commissioning sheet can be found in EST document CE131 During the commissioning process a number of variable settings have to be adjusted and set that are critical to the reliability and performance of the system These settings must be recorded on a commissioning certificate which is signed and handed over to the homeowner to certify that the equipment is safe legal and fit for use for its intended purpose The values and tolerances of any variable or adjustable parameters should be stated on this certificate to enable future service personnel or the homeowner to verify performance and safety 8 2 Maintenance Solar heating systems should be reviewed and inspected routinely e g system pressure fluid levels DTC panel flow rate lagging etc A planned maintenance inspection by the suitably qualified installer should be undertaken as a minimum every 3 years or at frequencies recommended by the solar manufacturer This maintenance inspection should include the following as a minimum visual check for shading of the collector growth of trees over time or alterations to the house or neighbouring houses may produce shading that wasn t there when collectors were installed the collector glazing must be undamaged and reasonably clean where visible paintwork or coating on the absorber must be sound
55. ting systems Guidance for professionals conventional indirect models and CIBSE document Solar heating Design and installation guide It should be noted that the dwelling as a whole incorporating these products must comply with all parts of the Building Regulations Issues of particular relevance where for example roof mounted solar collectors are fitted may include weathertightness fire safety structural safety etc Third party certification bodies e g NSAI Agr ment are available to assess compliance with all parts of the Building Regulations Applications for space heating heating of swimming pools and installations onto facades of buildings are outside the scope of this document pr SR 50 2 2010 E BOOQDOO E Q QOOONO COLLECTOR AUTOMATIC AIR VENT SHUT OFF VALVE COLLECTOR TEMPERATURE SENSOR FLOW TEMPERATURE GAUGE NON RETURN VALVE AIR COLLECTOR WITH MANUAL AIR VENT CYLINDER TWIN COIL SHOWN SYSTEM DRAIN LOWEST POINT FLOW LIMITER AND FLOW GAUGE SYSTEM FLUSHING POINT CIRCULATING PUMP PUMP STATION ASSEMBLY RETURN TEMPERATURE GAUGE EE SYSTEM PRESSURE GAUGE PRESSURE RELIEF VALVE SYSTEM FILLING POINT EXPANSION VESSEL PRESSURE RELIEF DISCHARGE VESSEL DIFFERENTIAL THERMOSTATIC CONTROLER DTC UPPER CYLINDER TEMPERATURE SENSOR LOWER CYLINDER TEMPERATURE SENSOR AUXILIARY HEAT SOURCE BOILER AUXILARY HEAT SOURCE IMMERSION IMMERSION AUXILIARY HEAT SOURCE TIMER FLOW FROM COLLECTOR RETURN TO COLLE
56. utput from the solar panels can be calculated using DEAP Appendix Q spreadsheet Procedure for Active Solar Thermal Systems contributing to both Domestic Hot Water and Space Heating Requirements Individual Heating Systems The output of the proposed collectors will be Solar DHW input Qs kWh y in Cell J55 on this spreadsheet This is based on the formula for Solar Energy available in Appendix H of DEAP i e Qs S X Zpanei X Aap X No X UF x f a no X F Ver Va H1 Where Qs Solar input kWh year S Total solar radiation on collector kWh m year Zpanel Overshading factor for the solar panel Aap Aperture area of collector m No Zero loss collector efficiency UF Utilisation factor a Linear heat loss coefficient of collector Wim K f a ho Collector performance factor 0 87 0 034 a1 no 0 0006 a1 no 38 pr SR 50 2 2010 E Var Effective solar volume litres Va Daily hot water demand litres TU Mart Va Solar storage volume factor 1 0 0 2In Ver Va subject to f Ver Va lt 1 0 The design of solar storage affects the performance of the whole solar system Dedicated solar storage Vs implies that no other source can normally heat the solar pre heat volume In the case of a combined store the effective solar volume Ver is equal to the dedicated solar storage Vs plus a factor times the volume of the remainder of the system Vp In the case of a combined cylinder this factor is 0 3
57. will be the area of the collector exposed to the wind is the permeability factor obtained from BS 5534 pr SR 50 2 2010 E S is the substrate shielding factor obtained from BS 5534 Key to zones RES 2lmie aa 21m s to 23m s xv 23m s to 25m s gt 25m s Figure B 1 Estimated maximum 60 minute wind speeds B 2 Sample wind load calculations for roof mounted collector Zone Il Example The site is in Navan Co Meath 30 km from coastline The solar collector is mounted 80 mm above the roof surface in the central roof area The array size is 1 4 mx 1 7 m 33 pr SR 50 2 2010 E The building ridge height is 8 m Site altitude is 35 m above mean sea level Roof pitch is 30 F CCa Cf Qp Ze Arer qplZe Ce Z Ap Ce Z exposure factor 2 26 from Figure NA 7 I S EN 1991 1 4 qb 0 613v Vb basic wind velocity Cait Vbmap Cart altitude factor 1 0 0014 As site altitude metres above mean sea level 35 m Vbmap basic wind speed from Figure NA 1 I S EN 1991 1 4 25 m s Vb 1 035 x 25 25 88 m s qb 0 613 x 25 88 411 Pa Qp Ze 2 26 x 411 929 Pa Ct 0 2 and 0 4 for wind blowing to front of collector from Table 7 4a 1 S EN 1991 1 4 0 5 for wind blowing from either side or the rear of collector from Table 7 4b I S EN 1991 1 4 CsCa 1 0 Aref 1 4 m x 1 7 m 2 38 m From 1 0 x 0 2 x 929 x 2 38 442 N upwards acting From 1 0 x 0
Download Pdf Manuals
Related Search