5125 UM B5-18-05
Contents
1. S PDIF RCA Coaxial Output 3 RCA Audio L R Video Data Interface Serial Port RS 232 9 pin D sub type Power input jack for 12 24 V DC System and Memory Flash Memory 2 Mbytes SDRAM 8 Mbytes EEPROM 64 kBytes Main processor STi 5518 General Data External power adaptor from 90 240 V AC 50 60 Hz to 12 V DC Power consumption max 25 W Stand by mode 13 W Operating Temperature 5 C 45 C Storage Temperature 0 C 50 C Humidity 25 70 Size WxHxD in mm 280 x 40 x 200 Weight 2 kg www strongsat com2. manual it is recommended to consult your dealer 1 4 Storage Your receiver and its accessories are stored and delivered in a well protective packaging against electric shocks and moisture When unpacking it make sure that all the parts are included and keep packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to store the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 1 5 Equipment Set up We recommend you to consult a professional installer to set up your equipment Otherwise please follow the following instructions m Refer to the user manual of your TV and or your antenna m Make sure that the SCART cable is in a good condition m Make sure that the SCART cable connections are well shielded m Make sure that the outdoor components of the antenna are in good condition www strongsat com 5 STRONG w DIGITAL TV 2 0 Your DVB T Receiver 2 1 Front Panel Please see inside cover Figure 1 1 Power Button Turns the receiver ON OFF 2 Stand BY ON SIGNAL 3 LEDs The red LED is the stand by indicator The green LED is the Power On indicator The orange LED lights up once you correctly receive a terrestrial signal 3 UP DOWN Buttons Move the cursor UP DOWN in Menu state Changes the channels UP DOWN in no menu state 2 2 Rear Panel Please see
3. OK or the Right button and set the date the way you have set the time 2 Press the BACK button until you go back to the Main Menu www strongsat com 13 STRONG w DIGITAL TV m Power on Channel This function allows you to set the channel you want when the receiver turns on To set the power on channel apply the following steps lt Please see inside cover Screen 16 gt 1 Select Power on Channel and press OK or the Right button m Last Viewed The receiver will start up with the channel that you viewed before turning the receiver off m Define channel This function allows you to set the channel you want when the receiver turns on To define the channel apply the following steps 1 Press OK or the Right button and select in the TV or radio list of channels the channel you want to have your receiver start up with m System Information The system information displays information about your receiver such as model number software and boot version To check system information apply the following steps 1 Select System information and press OK or the Right button lt Please see inside cover Screen 18 gt m Factory Reset Be careful when using this function because it will erase all the data and parameters you may have set earlier to your receiver Once you have made a Factory Reset you will have to re install your preferences and re scan your channels To reset your receiv er to factory default apply the following steps
4. To unlock the channel repeat the procedure Change Video Package Identifier V PID Audio A PID Program P PID Values 1 Apply the first four steps detailed in Change name of channel described previously 2 Using UP DOWN or P P keys select PID field lt Please see inside cover Screen 8 gt 3 Using the numeric keypad 0 9 enter the new value 4 Move your cursor to the OK field and press the OK button Deleting Channels from channel list You can delete channels from the channel list by applying the following steps Press the Menu button Using UP DOWN keys select Service Organizer and press OK Press the Blue Delete button lt Please see inside cover Screen 2 gt Using UP DOWN or P P keys on your remote select the channel Press the Red button to delete the selected channel Press the Green button to delete all channels from the list Press the Yellow Button to exit the delete menu NOU gt Q N mer STRONG DIGITAL TV 5 1 2 Favourite Organizer Menu This menu enables you to organize your Favourite channels list All the channels that you have marked as your Favourite in the Service organizer menu can be sorted by applying the following steps 1 Press the Menu button lt Please see inside cover Screen 1 gt 2 Using UP DOWN keys select Favourite Organizer and press OK lt Please see inside cover Screen 9 gt m Sort Red button Same as the Sort function of Service Organ
5. Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select Channel Set up and press OK 4 Using UP DOWN keys select Manual Scan and press OK 5 Using LEFT RIGHT keys enter wanted Channel No Frequency and Bandwidth and press OK With the menu Channel Management Please see inside cover Screen 24 you can manually delete single and or all channels and rescan new ones Press OK to confirm Note Automatic scanning process can only be successful when having selected the correct country inside the menu 5 1 4 2 5 1 4 4 Parental Lock Changing PIN Code Please see inside cover Screen 25 This function changes the Personal Identification Number PIN that is used to control access to the menu and individual channels In this function you can lock unlock channels and you can change your PIN code by applying the following steps m To lock unlock the menu please apply the following steps 1 Press the Menu button on your remote Using UP DOWN keys on your remote select Installation and press OK The receiver will ask you to put your PIN code This PIN code is currently set to 0000 Using UP DOWN keys select Parental lock and press OK Using RIGHT LEFT keys you can select either lock or unlock and press OK By selecting lock the receiver asks you to enter your PIN every time you want to access the menu By selecting unlock it gives you the possibility to acc
6. amplifier using a coaxial cable m Do not forget to turn the S PDIF function on Main menu gt Installation gt PIN code 0000 gt TV VCR Settings gt SPDIF Output gt On 3 1 4 Connecting a serial cable for downloading software Please see inside cover Figure 7 m Connect the RS 232 connector on the back of your receiver to the Serial port of your computer using a serial cable m Instructions on how to download software can be found on our website www strongsat com support gt downloads www strongsat com 7 STRONG _ _ ans DIGITAL TV 4 0 Starting up Ensure that your terrestrial receiver is correctly connected to your television and DVB T antenna and that your terrestrial signal is of good quality If you are not sure about this then ask your local Strong dealer to check your installation or terrestrial signal 4 1 Starting up for the First Time m Connect your DVB T receiver as under point 3 described m Enter the lt System Setup Language setting Menu language gt Press OK button to confirm your selection Press the Back button until you go back to installation menu m Follow the path lt Installation PIN 0000 Country Selection gt Select country and press OK button Once selection is confirm Country Selected Sucessfully appears m Follow the path lt Installation PIN 0000 Channel Set Up Auto Scan gt to select the automatic scan search option for all available TV and Radio progra
7. for navigating within the OSD Menus Left Right In channel list used to scroll list prev next 10 items duplicate Page Page buttons 10 OK To confirm actions in the menu systems In view mode displays the current channel list For example TV Radio or Favourite 11 MENU The main menu for setting up the receiver 12 BACK Exits the current OSD page In TV mode switches back to previous channels 13 AV Selects TV or Digital TV 14 Information lt Please see inside cover Screen 26 gt Shows program information PART 1 e English 15 EPG 16 PAUSE 17 AUDIO 18 PAGE Plus Minus 19 Color Buttons 20 0 9 www strongsat com lt gt 7RONG DIGITAL TV Display the EPG Electronic Program Guide EPG shows the event informa tion on the current channel by time zone EPG is divided into Weekly mode Daily mode and Extend mode It provides timer based recording and automatic power ON Off The event is displayed only if the channel supports EPG If you press EPG the Weekly mode is displayed as default m Weekly Red Button The current TP channel list is displayed on the left and the event information is displayed on the right by time zone lt Please see inside cover Screen 27 gt m Daily Green Button If you want to display the Daily mode of the current channel press Green Daily In the daily mode the receiver shows the designated channel in PIG and displays the channel event in detail lt Please see in
8. lt gt 7RONG DIGITAL TV AAA Digital Terrestrial Receiver SRT 5125 User Manual www strongsat com STRONG O 1 2 5 Digital Terrestrial Receiver C JJ 3 1 Figure 1 2 1 O aro 7 8 6 5 3 9 Figure 2 Figure 4 Figure 5 Figure 6 q esa man Gmm DIGITAL AUDIO VS SPDIF RY V O e O FJ lt gt 7RONG DIGITAL TV Table of Contents 1 0 11 1 2 13 14 1 5 2 0 2 1 2 2 3 0 3 1 3 1 1 3 12 3 1 3 3 1 4 4 0 4 1 5 0 51 Salil Del 32 5 13 5 1 4 5 1 4 1 5 1 4 2 5 1 4 3 5 1 4 4 5 15 6 0 A 1 A 2 Usage Safety Instructions Features amp Accessories Safety Precautions Storage Equipment Set up Your DVB T Receiver Front Panel Rear Panel Connections Connecting to your TV amp VCR Basic connection with a Scart cable Connection with Audio Cable RCA Connectors Connection to a digital audio
9. 1 Select Factory Reset and press OK 2 Enter your PIN Code The receiver will reset itself to the original factory settings 3 Before using the function Automatic Scan search see 5 1 4 3 select Country selection 5 1 4 2 first Note Your PIN code will change back to the factory setting 0000 5 1 4 2 Cou ntry selection Please see inside cover Screen 19 To install your receiver with all terrestrial TV and Radio programmes available in your country go to Country selection 1 Press the Menu button 2 Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select Country Selection and press OK 4 Using UP DOWN keys select your country and press OK to confirm 5 1 4 3 Channel Set Up Please see inside cover Screen 20 The channel set up is for downloading all DVB T available TV and Radio channels There are two possibili ties for downloading the programmes m Automatic Scan search Please see inside cover 21 22 1 Press the Menu button 2 Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select Channel Set up and press OK 14 www strongsat com sn a STRONG DIGITAL TV 4 Using UP DOWN keys select Auto Scan and press OK 5 The screen Auto Detection appears first Thereafter the screen Auto Scan follows Wait until the automatic scan has finished m Manual Scan search Please see inside cover Screen 23 1 Press the Menu button 2
10. al functions of the receiver to prevent unauthorized users such as children to view channels that are not suit able for them A PIN code is required to use of the parental lock PID The transmitted packages have identifiers PID that tells the receiver what to do with the received information Receivers normally use four types of PID these are V PID video PID A PID audio PID P PID Program PID and data PID EPG information PIN CODE Personal Identification Number A four digit code that is used for locking unlocking e g with the parental control feature RS 232 Serial data port www strongsat com 19 STRONG e casa DIGITAL TV Technical Specifications Demodulator Demodulation COFDM 16QAM 64QAM OFDM Spectrum 2K 8K Video Decoder Profile level MPEG 2 Main Profile Main Level Input Rate MPEG2 Video decoding ISO EC 13818 2 up to 15 Mbits s Video Resolution 720 x 576 pixels for PAL Aspect Ratio 4 3 16 9 Pan amp Scan Letterbox Audio Decoder MPEG MusiCam layer amp II Sampling rate 32 44 1 48 kHz Audio mode Stereo Joint Stereo Dual Channel Mono AC 3 Tuner Front End DVB T Input Frequency Range VHF 47 230 MHz and UHF 417 862 MHz RF input Signal Level 87 20 dBm Loop through frequency range 47 862 MHz Remote Control With colour buttons and short cuts Batteries 2 Size AAA Connectors Antenna input IEC 60169 2 Female RF Loop output IEC 60169 2 Male 2 SCART TV and VCR
11. amplifier using the S PDIF output Connecting a serial cable for downloading software Starting up Starting up for the First Time Basic settings Main Menu Service Organizer Menu Favourite Organizer Menu The Timer Menu The Installation Menu System Set up Menu Country Selection Channel Set Up Parental Lock Changing PIN Code Games Basic functions of Remote Control Trouble Shooting Glossary of terms www strongsat com PART 1 e English COCO OO O9 O O O O O M ON O HW Ww wna STRONG DIGITAL TV Thank you for choosing this Strong terrestrial receiver This receiver is of our latest development and it is designed to be capable of upgrading its software through the PC It is highly recommended that you read this manual carefully to safely install your receiver and to achieve its optimum performance 1 0 Usage This user manual is applicable for Strong SRT 5125 Digital Terrestrial Receiver and its related accessories It is advised that first time and experienced users read this manual in order to safely install the receiver Strong has supplied this product with the most recent innovations of software and hardware Strong reserves the right to make changes in production to the software used by your terrestrial receiver without prior notification In order to maintain and ensure that your receiver is compatible and updated with the most recent software technology we recommend that you visit our website to che
12. ck the latest software 1 1 Safety Instructions Warning DO NOT INSTALL YOUR RECEIVER m In a closed or poorly ventilated cabinet m Directly on top of or under any another equipment m On a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or near any other equipment that generates heat m To rain or intense moisture m To any shock which may cause permanent damage to your receiver m To any magnetic objects such as loudspeakers transformers etc m To intense vibration m Never open the cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards Your warranty will be void if the receiver has been opened When the receiver is not used for a long period of time you should unplug the power cord from the wall socket m Do not use a damaged power cord It may cause a fire or an electrical shock m Do not touch a power cord with wet hands It may cause an electric shock m Place the receiver in a well ventilated environment When you are connecting the cables be sure that the receiver is disconnected from the mains supply voltage m Do not use your receiver in humid environment Make sure you read this user manual before installing your receiver This manual provides complete instructions for installing and using this receiver The following symbols will be used as follows Bold Characters Re
13. ct how you want the OSD to be m OSD Timeout Press OK or the Right button and select how long you want the information banner to be on the screen when starting up your receiver or when changing channels LCN Mode Logical Channel Numbering Automatic numbering of channels through antenna signal Only usable when broadcaster supports LCN function In this case switch LCN Mode ON Note When LCN Mode is switched ON it disables function described under 5 1 1 Sorting channels 2 Press BACK until you go back to main menu m Time setting The system uses GMT Greenwich Mean Time as a default To set the time apply the following steps lt Please see inside cover Screen 15 gt 1 Select Time Settings and press OK or the Right button m Select GMT usage Press OK or the Right button and use the UP DOWN buttons to select the GMT usage ON or OFF ON activates the selection Time Zone OFF activates Set Local Time Date Press OK to save your setting m Select Time Zone Press OK or the Right button and a list of the GMT plus or minus the hours you need for your country is displayed Using UP DOWN keys select the correct one and the receiver will automatically show the current time in your country To set the time manually m Select Set Local Time Press OK or the Right button Use your UP DOWN buttons or Numeric buttons 0 9 to set the local time When set press OK to save the local time m Select Set Date Press
14. ess the menu all the time without the receiver asking you for a PIN code m To change your PIN code apply the following steps 1 Press the Menu button on your remote Using UP DOWN keys select Installation and press OK Using UP DOWN keys select Parental lock and press OK Using UP DOWN keys select Old PIN and enter 0000 Using UP DOWN keys select New PIN and enter a new PIN Using UP DOWN keys select Verify PIN and enter the same new PIN Press the Green button on your remote to save amp Exit DU Q N Press the Back button until you go back to main menu You are recommended to write down your new PIN code In case you forget it you can reset your receiver to factory default settings but you will lose all information you saved Your Personal PIN Code www strongsat com 15 STRONG vieu DIGITAL TV 5 1 5 Games If you want to play a game apply the following steps 1 Press the Menu button on your remote 2 Using UP DOWN keys on your remote select Games and press OK 3 Using UP DOWN keys on your remote select the game you want to play and press OK 6 0 Basic functions of Remote Control Please see inside cover Figure 3 All features of the set top box can be controlled with the remote control Inserting batteries to the Remote Control Unit 1 Open the battery cover on the rear of the remote control Unit 2 Insert the two supplied batteries 1 5V observing the polarit
15. in voltage of 90 240V AC Auto selectable 50 60Hz 5 The receiver operates with a voltage between 12 24 Volts DC You may use the standard supplied Cigarette Lighter Power cord for use of your receiver in mobile solutions i e camping boat Note Please make sure that only the original supplied power adaptor Is used in combination with your receiver 6 www strongsat com marries STRONG DIGITAL TV 3 0 Connections 3 1 Connecting to your TV amp VCR Note The SRT 5125 does not have a UHF modulator so you only can connect it to TV over scart or RCA connector 3 1 1 Basic connection with a Scart cable Please see inside cover Figure 4 m Connect the antenna cable to the ANT IN connector m Connect the TV scart connector at the back of the receiver to the scart in connector on your TV set Note If you have a digital audio amplifier with a digital audio input use the S PDIF output 3 1 2 Connection with Audio Video Cable RCA Connectors Please see inside cover Figure 5 m On the back of your receiver you will find the RCA connectors Audio Left amp Right Red amp white Video Yellow Install an audio video cable between the RCA connectors of the receiver and those of your TV set or amplifier 3 1 3 Connection to a digital audio amplifier using the S PDIF output Please see inside cover Figure 6 m Connect the S PDIF out connector on the back of your receiver to the S PDIF input connector of your digital
16. inside cover Figure 2 1 ANTENNA INPUT Connect the antenna cable to this connector 2 RF OUTPUT Gives you the possibility to bypass anologue signals from your antenna to your TV VCR or another equipment 3 AUDIO Right Red RCA and Left White RCA These connectors give you the possibility to connect the audio signal to an external amplifier or to the audio input of your TV 4 VIDEO Yellow RCA This connector has a constant video signal for additional VCR connections 5 TV Scart Connector Use this connector to connect your receiver to your TV using a scart cable 6 VIDEO Scart Connector Use this connector to connect your receiver to your video recorder using a scart cable Your video signal will now be looped through to your TV 7 RS 232 Serial Port This serial port can be used to connect your PC to your receiver and enables you to download new versions of software into your receiver Detailed infor mation about downloading software into your receiver can be found on our website www strongsat com Note It is recommended to ONLY use the original software provided via our website Loading other versions of software not adapted to your model number can cause severe damage to your receiver and will not be covered by the warranty 8 S PDIF Use this coaxial output to connect your receiver to the input of your digital audio amplifier 9 Power Supply Connection for external power supply in the package Your adaptor needs a ma
17. izer menu lt Please see inside cover Screen 3 gt m NxtFav Next Favourite Group Green button Shows the next Favourite group list m Edit Yellow button You can edit the name of the Favourite group in the same way as you change a channel name in the Service Organizer Menu lt Please see inside cover Screen 6 gt m Remove Blue button Removes the selected channel directly from the Favourite list that was selected 5 1 3 The Timer Menu The timer can automatically switch on or off your receiver at any time This enables you for example to record programs with your VCR while you are not at home It also can be used to wake you up at the time you set it Please apply the following steps 1 Press the Menu button lt Please see inside cover Screen 1 gt 2 Using UP DOWN keys on your remote select Timer Menu and press OK lt Please see inside cover Screen 10 gt m Timer number You can select up to 8 different events m Timer State Set to Enabled to use the timer function or Disable to stop the timer functions of the timer number you selected Timer mode You can select the following functions in the timer mode 1 Power On The receiver powers on at the designated date and time 2 Time interval The receiver switches on at the designated date and time displays the channel and then switches off at the designated date and time The value set at the ending time 3 Power Off The receiver power
18. m the list Sorting Channels from the channels list To sort your channels please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Service Organizer and press OK 3 Enter PIN CODE 0000 default code and press OK 4 Press the Red Sort button to sort your channels lt Please see inside cover Screen 2 gt m f you press the Red Name button you can sort the list of channels alphabetically lt Please see inside cover Screen 3 gt m If you press the Green Type button you can sort the channels by the type of the channel organize the Favourite list m If you press the Yellow MUX button you can edit the channels per broadcasted frequency m f you press the Blue Manual button you sort the channels manually A check mark will be shown on the selected channel Use the UP DOWN buttons to move to the position that you want the channel to be at and press the Blue manual button once again The channel will then be moved to the position you selected Once you have finished sorting the channels press the Back button until you are back in the Normal TV mode A message that the receiver is saving the changes you made will be displayed Setting Favourite channels from the channel list You can set a list of Favourite channels from the current TV Radio channels list To set your Favourite channels please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Service Organi
19. mmes Press OK button to confirm your selection and wait Press the Back button until you go back to main menu Note It is important to select the correct country inside the menu before the scanning process starts to avoid scanning problems 5 0 Basic settings Note Every time the receiver asks you to put your PIN code enter 0000 on your remote control using 0 9 numeric keypads Remember To switch between the TV Radio channels list you will have to press the TV RAD buttons on your remote accordingly 5 1 Main Menu Please see inside cover Screen 1 All the important settings and features of your receiver can be operated from the Main Menu The Main Menu consists of several sub menus such as Service Organizer Favourite Organizer Timer Installation and Games To display and navigate through the main menu of the receiver please apply the following steps 1 Press the Menu button 2 Use UP DOWN keys to navigate through the menu 3 Press OK button every time you select an item from the menu 4 Press the Back button to terminate an operation 5 Press the Back button until you go back to main menu Tip Always read the Help bar displayed at the bottom of your screen 8 www strongsat com wna a STRONG DIGITAL TV 5 1 1 Service Organizer Menu The Service Organizer menu enables you to sort channels make your own Favourite channels list edit channel names and delete channels fro
20. ode Press OK or the Right button and set your screen mode to 4 3 Full Screen 4 3 Letter or 16 9 m Audio Output Press OK or the Right button and set your audio output to Stereo Left only or Right only Left or Right is for mono TV sets m SPDIF Output Press OK or the Right button and activate your S PDIF out put on the back of your receiver so you can connect it to a digital Audio amplifier using a coaxial cable D wuwstrongsat com wn STRONG DIGITAL TV m VCR Scart Press OK or the Right button and set the scart output to Auto or STB Set Top Box If set to STB the VCR scart signal is not auto matically looped through m Antenna power ON OFF Antenna Power is preset in OFF Mode Only when using an active antenna this function must be switched ON Press OK or the Right button to select ON 2 Press BACK until you go back to main menu m OSD Settings You can set the OSD On Screen Display on your TV to your personal preferences You can change the OSD settings by applying the following steps 1 Select OSD Settings and press OK or the Right button lt Please see inside cover Screen 14 gt Colour Scheme Press OK or the Right button and set the colours of the OSD menu to Basic Colour 1 or Colour 2 m Transparency Press OK or the Right button and select how transparent you want your OSD Brightness Press OK or the Right button and sele
21. power Wait 30 seconds and connect to mains power again and now check if the unit is working as expected If the receiver does not work properly after checking the trouble shooting section please contact the dealer Don t open the receiver cover it may cause an electrical shock due to high current voltage and the warranty of your receiver will be void if the receiver has been opened Symptoms Cause The green red lights on front panel do not light up The power cord is not plugged in No picture and sound TV is set to wrong channel No picture and sound Problem in cable connections between receiver and TV No picture and sound Receiver hang up The receiver or TV is in MUTE mode No sound No sound or picture Problem in scart cable connections between receiver and TV No picture Antenna not Strong enough The receiver displays the This is normal the bad message No or bad signal during bad weather conditions weather is interfering the signal of the antenna The receiver displays the Wrong parameters set in message the menu No or bad signal The batteries of the remote control are not The remote control is not working inserted or exhausted 18 Solution Check that the power cord is plugged into the wall outlet Check if the TV is switched on and set your TV to the correct EXT AV channel Check if the scart and cable is connected correctly to the TV and to the back of the recei
22. presents a button on the remote control or the receiver Italic Characters Represents a menu item within the On Screen Display OSD Menu www strongsat com 3 STRONG mieu DIGITAL TV 1 2 Features amp Accessories SRT 5125 Digital Terrestrial Receiver m Easy to use Graphic MENU Interface m Multi lingual support on screen Menu English Spanish Italian French German Swedish Danish Hungurian Czech m RS 232 port for updating control software and additional services m Automatic channel scan options m 2 SCART Connectors TV VCR m 3RCA Connectors CVBS Audio Left Right m Multi Language function Menu Audio m Front Panel Buttons m Editing Functions TV or Radio Channel Channel Name m EPG Electronic Program Guide for on screen channel information m Over 1000 channels memory capacity m Four Favourite lists for both TV and Radio m 3 Operation Modes Digital TV Digital Radio Favourite m Digital Tuner with Loop through output m MPEG 2 Main Profile at Main Level m Teletext VBI m Support of active antenna by 5V output m Supports software downloading via PC m S PDIF output for connection with a digital audio amplifier Accessories m User s Manual m Remote control unit m 2x Batteries AAA type m External power supply m 12 24 V DC Cigarette Lighter Power cord Note The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries 1 3 Safety Preca
23. s go to System Set up menu Then please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select System Set up and press OK m Language Settings You can change the language of the menu audio and subtitles by applying the following steps lt Please see inside cover Screen 12 gt 1 Select Language Settings and Press OK or the Right button 2 Select Menu Language and Press OK or the Right button 3 Using UP DOWN keys select the language in which you want your menu to be displayed and press OK The screen of the menu will change to the language of your choice 4 You can also choose your preferred first audio language second audio language and the subtitle language by applying the same steps 5 Press BACK until you return to the main menu m TV VCR Settings lt Please see inside cover Screen13 gt You can set the TV VCR settings to your personal preferences Check your TV and VCR user manuals for the correct settings You can change your TV VCR settings by applying the following steps 1 Select TV VCR Settings and press OK or the Right button m TV Mode Press OK or the Right button and set your TV mode to Multi PAL or NTSC m Video Mode Press OK or the Right button and set your VCR mode to CVBS Composite video or RGB preferred option if your TV set is compatible with it m Screen M
24. s off at the designated date and time Press OK now you will see the channel list select a channel and Press OK m Timer Cycle You can set the cycle of the action designated in the timer mode one time Every Day or Every Week m Date You can set the starting date of the timer action m Time You can set the starting time of the timer action m Ending Time You can set the ending time of the channel view when the Timer mode is on Time Interval m Channel You can select the channel to be shown when the receiver timer mode Powers ON 3 Press the Red button to save and proceed with another timer event www strongsat com 11 STRONG e ens DIGITAL TV 4 Press the Green button to save and exit the timer menu 5 Press the Yellow button to exit the timer menu WITHOUT saving the settings Tip You have to select the channel starting time and ending time settings if the Timer mode is Time interval An error message will appear if any of the settings are incorrect 5 1 4 The Installation Menu Please see inside cover Screen 1 All settings that are related to TV and channel scan search are within this menu The installation menu contains several sub menus such as System Set up Country selection Channel Set up and Parental Lock To access the different sub menus apply the following 5 1 4 1 System Set up Menu Please see inside cover Screen 11 To install your receiver to your personal preference
25. side cover Screen 28 gt m Extended Yellow Button If you press the Yellow button the receiver shows the detailed information of the current event lt Please see inside cover Screen 29 gt Timer Blue Button Move the cursor to an event in the required time zone and press Blue Timer The timer is then set to the designated time See Timer Menu Described in section 5 1 3 for details of the timer m Press BACK to close the EPG menu Freezes the picture Shows the list of available audio languages for the channel you are watching You can change the audio language you want to hear by using the Up Down keys and pressing the OK button In addition it sets the current channel audio to stereo left mono or right mono Pressing the sound button changes the sound icon on the top banner The selected sound information is saved by channel and is set to the sound mode when you watch the channel Scrolling page by page Page for the next 10 items Page for the previous 10 items Within the Videotext mode the color buttons follow the color codes of the broadcaster In the menu follow the color codes for various functions Numeric Direct entry of numerical functions in the menus or in channels selection 17 PART 1 e English lt gt 7RONG DIGITAL TV A 1 Trouble Shooting Occasionally receivers can hang up just like with a PC so you are recommended to reset the receiver by disconnecting it from mains
26. t Press OK on the channel name and the keyboard will appear on screen lt Please see inside cover Screen 6 gt 6 Use UP DOWN or P P keys to select a letter and the OK button to overwrite the current chan nel name letter by another letter Go up with the cursor into the line of the new name and press OK to confirm the changed name Press BACK to go back to the menu Change lock function If you lock a channel you can only watch it from the TV list after entering your PIN Code To change lock function apply the following steps 1 Apply the first four steps detailed in Change name of channel Described in section 5 1 1 2 Using UP DOWN or P P keys select Lock field lt Please see inside cover Screen 7 gt 3 Press OK and enter your PIN Code 4 The lock function will be marked 5 Move your cursor to the OK field and press the OK button 6 To unlock the channel repeat the same procedure WN Change the Skip function If Skip function is activated the channel will be skipped when you are scrolling through the TV list in nor mal watching mode Please apply the following steps 1 Apply the first four steps detailed in Change name of channel Described in section 5 1 1 2 Using UP DOWN or P P keys select Skip field lt Please see inside cover Screen 8 gt 3 Press OK and enter your PIN Code 4 The skip function will be marked 5 Move your cursor to the OK field and press the OK button 6
27. utions To maintain your receiver s optimum performance you are advised to apply the following safety precautions m Read this manual carefully and make sure you fully understand the instructions given m Refer all maintenance or servicing to suitably qualified personnel m f you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply m Do not use alcohol or ammonia based liquids to clean the receiver m Do not open the receiver cover as you will be exposed to a shock hazard 4 www strongsat com marte STRONG DIGITAL TV m Do not open the receiver cover this will void your warranty m Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside m Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock m Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment m Please ensure that that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver m It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment m f the receiver does not operate normally even after strictly following the instructions in this user
28. ver Switch off receiver disconnect the main power cord of the receiver from the 220 V main power After 30 seconds reconnect to the main power and check if it is working properly Press the MUTE button on the remote control unit of your receiver and TV Firmly press the scart connectors on the backside of the TV and receiver Replace the scart cable Check the signal strength with a spectrum analyzer and adjust your antenna correctly Once the weather is better the picture will appear If not check if there is no snow on your antenna Check settings of antenna and Channel set up menu Check whether the batteries are inserted correctly in your remote control Check the batteries and if they are exhausted replace them www strongsat com STRONG DIGITAL TV A 2 Glossary of terms DVB T Digital Video Broadcasting Terrestrial Digital TV via antenna same as DTT Digital Terrestrial Television EPG Electronic program guides that are transmitted by some broadcaster to display information guide about a program content MPEG The Moving Picture Experts Group is founded by the ISO MPEG is a standard method for digital transmission of video and audio Network A network which is also known as a bouquet is a set of channels that is offered by a single broadcaster PAL Referring to the Phase Alternate Line colour system adopted by European broadcasters Parental lock This function gives you the possibility to lock other sever
29. y and the AAA specification 3 Firmly replace the battery cover While viewing TV or Radio channels various functions can be applied using your remote control Outlined is an explanation of the buttons on your Remote and their corresponding functions that can be performed while watching TV or listening to the Radio See inside cover for the illustration of the remote control 1 STANDBY ON OFF Switches the Receiver ON or OFF 2 SUB Shows the list of subtitle languages the current channel supports You can change the subtitle language you want by using the Up Down keys and pressing OK on your remote 3 TEXT Enables Teletext 4 LIST Displays the list of channels you have scanned with your receiver You can change the channel you want to watch by using the Up Down keys and pressing the OK button The LIST button is disabled in the favourite channel mode because there can be a number of different channels on which you have different favourite channels 5 Mute Enables or disables the sound Mutes 6 TV RAD Switches between TV or Radio mode 7 FAV Displays the list of favourite channels If you press FAV on the remote control in No menu state You can preview the channel via PIG Picture in Graphic and move through the list of channels quickly with the CHANNEL UP CHANNEL DOWN buttons 8 CHANNEL Up Down Used for stepping through the channels or navigating within the OSD Menus 9 VOL Left Right Used for adjusting the volume or
30. zer and press OK 3 Press the Green Fav button to switch into Favourite organizer mode lt Please see inside cover Screen 2 gt 4 The default Favourite list names are Movie News Sports and Music 5 Using UP DOWN or P P keys select the channel and press the coloured button on your remote corresponding to the classification of the channel For example if you press the Red movie button the channel is designated as Movie Favourite channels A red heart will appear behind the channels name If the Red button is pressed again the selected channel is un select ed from Movie Favourite list lt Please see inside cover Screen 4 gt 6 One channel can be saved into more than one Favourite list You can change selected Favourite channels in Favourite Organizer menu 7 Press the Back button until you go back to main menu You can view the Favourite list you set by pressing the FAV button while you are watching TV or listening to a Radio channel www strongsat com 9 STRONG tart ein DIGITAL TV Editing Channels from the channel list You can change the channel name lock a channel and change the skipping functions Change name of channel To change the name of the channel please apply the following steps Press the Menu button Using UP DOWN keys select Service Organizer and press OK Using UP DOWN or P P keys select the channel Press the Yellow Edit button lt Please see inside cover Screen 2 and 5 g
Download Pdf Manuals
Related Search