BDA-M400 Funk -EN- (Rev-02) 01-10-2009
Contents
1. You can use the intelligent M400 electronic locking system for opening and engaging your furniture s locking mechanism with electronic convenience The M400 system allows you to issue selective access authorisations so that only authorised personnel are given access to specific items of furniture Entire locking systems with different access levels can be configured without a problem Wireless signals are not restricted to the confines of a room and do not require any direct line of vision Each electronic control unit in the M400 system works autonomously without being connected by cable to other control electronics or the power supply system You can program different transmitters with ease in each electronic control unit In normal operation the control electronics only respond to the transmitters programmed Each transmitter is unique and carries an unmistakable code As such it is sufficient to clear a transmitter s code from your control electronics to render the transmitter unusable for accessing your furniture To operate the system you will also need a LEHMANN wireless transmitter that is already in your possession or which you may purchase from your supplier or retailer NOTICE This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions this device may not cause harmful interference and this device must accept any interference received including interferen2. y 1 Press and hold down both buttons on the hand held transmitter 2 The indicator begins to flash for a while 3 When the indicator switches back to steady light programming has been completed 4 Now let both buttons go again 5 Observe the sight signals on the furniture If the signal flashes red green you have successfully switched over Indication at furniture optical system Switch on automatic locking Green LED permanently lit red LED flashes S Switch off automatic locking Green LED flashes red LED permanently lit N_A Important note All electronic units to which the hand held transmitter is programmed will be switched to the same state Do not place your hand held transmitter in the furniture when automatic locking is set If you wish to return to standard mode again repeat steps 1 5 The M400 locks automatically after approx 1 5 minutes BDA M400 Funk EN Rev 02 01 10 2009 Page 5 Monitoring of bolt position The M400 is equipped with a sensor for the bolt position in the extended state If the bolt after a closing command does not arrive at the final position it is an optical Warning output red LED display flickers If the bolt when receiving a Closing command is already in the end position so there is no additional closing Due to the suspension of the execution of a closing piece of furniture even after the locking when the open door possible Test function 3 Warning light
3. variety of function units doors roller shutters pull outs etc If you have any questions concerning system installation contact a firm of cabinetmakers or your supplier before commencing installation BDA M400 Funk EN Rev 02 01 10 2009 Page 3 e Getting started Before operating the system for the first time insert the batteries into the electronic control unit and RESET the system e Changing the batteries Undo screw J Open battery compartment lid Change batteries Make sure they are fitted the right way round Battery type LR6 AA alkaline 4 ATTENTION NiCad NiMH zinc carbon lithium batteries or other rechargeable batteries must not be used e Perform system RESET Once the system has been correctly installed and the batteries inserted the access codes can be programmed into the control electronics For safety reasons however RESET the system before putting it into operation so as to clear any codes programmed during the quality assurance process It is not possible to clear individual hand held transmitters System reset Insert T stick in Signals has been T Stick LEARN socket l l successfully press in and keep GREEN signals light up completed pressed then flicker GREEN The indicator then goes out Remove T Stick e Teaching your hand held transmitter T Stick Button 1 Button 2 Engage lock Open lock y Insert T stick into teach socket and press in for a mom
4. 1 Block the bolt Cr Closing command from the Handheld Transmitter e Technical specifications The system is not restricted to the confines of a room Frequency Wireless 2424 5 MHz Modulation GFSK Be sure to observe national legislation on permissible wireless frequencies Range Transmission reception range may be restricted by the building s structure 20 standard access codes 20 hand held transmitters can be programmed per electronic control unit Programming a 21st hand held transmitter will overwrite the 1st hand held transmitter and so forth Energy supply for electronic control unit Battery type 2x AA mignon cells alkaline 1 5V NiCad NiMH zinc carbon lithium batteries or other rechargeable batteries must not be used Temperature range Operation 5 C to 40 C at 30 to 80 relative air humidity non condensing Storage 25 C to 70 C at 30 to 80 relative air humidity non condensing LEHMANN Vertriebsgesellschaft mbH amp Co KG Postfach 2620 D 32429 Minden BDA M400 Funk EN Rev 02 01 10 2009 Page 6
5. Operating Instructions Basic Module E Globe Il M400 Wireless 2 4 GHz Contents General description and mode of operation maintenance and care Page 2 Installation and enclosure dimensions asana aaa eee eee Page 3 Getting started Changing batteries System reset Teaching transmitters Page 4 Function Battery warning Technical specifications Special function Page 5 Special function and Technical appendix a oa aaa a eee eee ee Page 6 e Safety precautions On changing the batteries ensure correct battery polarity and position Dispose of spent batteries in the proper manner Do not heat the batteries take them apart or short circuit them Never throw batteries into naked flames The batteries must not be recharged Keep the batteries out of children s reach Any person swallowing batteries must seek immediate medical advice Damaged and or leaking batteries may lead to acid burns and or poisoning e Advice on operation and care Do not pour any liquids into or over any of the system s components and never immerse the components in liquids The electronic units may be affected in relation to transmission and reception range if operated in the immediate vicinity of interference sources such as transformers ballasts lamps or similar devices Restrictions resulting from the structure of the building cannot be ruled out either The receiver should not be
6. ce that may cause undesired operation NOTICE Changes or modifications made to this equipment not expressly approved by Martin LEHMANN GmbH amp Co KG may void the FCC authorization to operate this equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help NOTICE This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Radiofrequency radiation exposure Info
7. ent or two Now remove T stick again Green LED lights up Briefly press button 1 or 2 LEDs light up on held held transmitter Signal goes out Hand held transmitter is programmed Important Notice After the first programming can be further hand transmitters are programmed on if the electronic in a sealed condition The same is true for a system reset and erasing channels manually BDA M400 Funk EN Rev 02 01 10 2009 Page 4 e Check for correct working order Button 1 Button 2 Engage lock Open lock E Briefly press button 2 Briefly press button 1 LED lights up green while LED lights up red while the motor is opening the lock the motor is engaging the lock Electronics battery warning The M400 has several battery warning levels See table below Indication on furniture level opticalsystem Meaning Effect Normaloperation is still LED indicator flashes at given regular intervals Red tw ice Low batteries Batteries Levelt briefly in succession should be changed soon Each time the button is pressed in the hand LED indicator flashes at held transmitter the lock regular intervals Red three Batteries are flat Batteries now only carries out Level 2 time briefly in succession mustbe changed the OPEN command e Special function Switching over to automatic locking Pressing a combination of buttons on the hand held transmitter you can switch the furniture lock over to automatic locking
8. exposed to direct sunlight Clean the system with a clean soft damp cloth only Do not use any cleaning products containing abrasives or solvents such as glass thinner alcohol benzene or ammonia as they may react adversely with the enclosure Treating any of the electronic and mechanical components improperly or in a way other than described in this user manual may lead to malfunctions BDA M400 Funk EN Rev 02 01 10 2009 Page 1 e General description The M400 electronic locking system is an accessory It is intended for home and office use inside buildings This user manual tells you how to operate the M400 system in the proper manner Very easy to handle the M400 system can be tailored to your specific needs It can be upgraded from a stand alone system to a complex and convenient locking system Wording and graphics have been prepared for you with care However no liability will be assumed for any mistakes that may have occurred Copyright 2009 by LEHMANN Vertriebsgesellschaft mbH D 32429 Minden All rights reserved These instructions must not be reproduced in any way print photocopy microfilm or other process or processed duplicated or distributed using electronic systems either in whole or in part without written consent from LEHMANN Vertriebsgesellschaft mbH The scope of items included by the manufacturer in the system as well as technical specifications are subject to change without notice e Mode of operation
9. rmation The radiated output power of the device is far below the FCC radio frequency exposure limits Nevertheless the device shall be used in such a manner that the potential for human contact during normal operation is minimized BDA M400 Funk EN Rev 02 01 10 2009 Page 2 e Application Installation Assembly The M400 electronic furniture locking system must only be used for locking homes home and office furniture Using the system in applications for which it is not intended may result in irreparable damage to it and render any claims null and void The points below explain the principal steps of the installation procedure and must be followed when fitting the M400 system to furniture Before installing the system insert the batteries into the control electronics and program your transmitter s access code Connect the components and satisfy yourself that the system works correctly Only install the system within an unlocked state The indicator module should be installed in such a way that you are provided with a good line of vision If you install the optoelectronics so that they are physically separated from the control electronics the connecting cable between these system components must not exceed a length of 1 m Please refer to the fitting instructions from the manufacturer of your furniture for the correct way to attach the M400 system to your furniture LEHMANN supplies a wide range of accessories with which you can lock a
Download Pdf Manuals
Related Search