Wzzard Sensor Node User Manual - Industrial Networking Solutions
Contents
1. o PP 3 3V 3 3V power input 3 3REF 3 3V output reference AIN1 Analog Input 1 AIN2 Analog Input 2 AIN3 Analog Input 3 DO Digital Output DIN1 Digital Input H1 DIN2 Digital Input 42 DO1 Digital Output 1 DO2 Digital Output 2 GND Ground Input 12 CONNECTING YOUR SENSOR WITH M12 MODELS ANALOG AND DIGITAL While installing your batteries confirm that the wire harness from the M12 port is connected to the circuit board inside in Wzzard Edge Node Wire your M12 cable according to the charts below Wzzard M12 Pinout 13 TERMINAL BLOCK CONNECTIONS THERMOCOUPLE Remove the 4 screws that hold the top of the Wzzard node in place Thread the thermocouple wires through the conduit and attach them to the terminal block 1 Thermocouple input 1 positive 2 Thermocouple input 1 negative 3 Thermocouple input 2 negative 4 Thermocouple input 2 positive Close the Wzzard node and replace the 4 screws 14 POWERING YOUR WZZARD EDGE NODE INSTALLING BATTERIES Remove the 4 black screws that hold the top of the node in place Install 2 3 6 V AA Thionyl Chloride lithium batteries As with all batteries these are a fire explosion and severe burn hazard Do not burn or expose them to high temperatures Do not recharge crush disassemble or expose the contents to water Properly dispose of used batteries according to local regulations by taking it to a hazardou2. CSA Class 1 Div 2 Groups A B C D ANSI UL equivalent Regulatory Approvals ROHS and WEEE Compliant Digital Inputs Voltage range 0 48 VDC Vi 0 97V Maximum Vin 1 8V Minimum Pull up current 32uA Type Sourcing PNP Sinking NPN Software selectable input Isolation None Rate Frequency Inputs TENES Can handle frequencies between 1 Hz 1000 Hz Uses the falling edge or rising edge based on the Invert Enabled setting Counter Input Channels Actively counts either the falling edge Invert enabled or rising edge Invert disabled Can use a multiplier to convert to a unit type or count 2 selectable shared with Digital inputs Rolls over at 999999 9 Analog Inputs Input ranges 0 5 VDC 0 20 mA Accuracy 259C Voltage 0 1096 full scale reading 0 2096 max Current 0 1196 full scale reading 0 2496 max Resolution 12 bit Input load 100 Mega ohm 0 5VDC 2500hm 0 20ma resistance Thermocouple Input Types Supported JandK Ranges Supported Type J 210 to 41 200 C Type K 270 to 41 372 C Resolution 0 25 C Accuracy Typical 2 C 6 C over the temperature range of 40 to 80 C boltion None 26 RADIO SPECIFICATIONS SmartMesh IP 802 15 4e RADIO SPECIFICATIONS Parameter Conditions Min Typ Max Units Frequency Band 2 400 2 4835 GHz Number of 15 Channels Channel 5 MHz Separation Channel Clear 2405 5 k 11 MHz Frequency Modulation IEEE 802 15 4 Direct Se
3. nennen teen nnne nnne en testen intent nnne en nent tnt to tnnt nnne nns 15 installing a IRR 15 HI EE 15 Mount Your Wzzard Edge Node NA NA INA GAN aer enar tia Par ELENA 16 Connecting to Your Intelligent Edge Nodes via Bluetooth LE eene nennen 17 Install the Wzzard App on Your Handheld Device rrrrarrnrvnrennrrvneennrnnnrenvensensrreneennnnessernnnsennrreneennrssssennnnssnsrsensennnnr 17 CONFIGURING YOUR Wzzard Intelligent Edge Nodes seen enter enn enne 18 KE lo er 18 Device ConfigulatiOn io i etico P e e ed b hat An Qux ene e ai ever bes duc EHE 18 GOO LOCAUOM AA AA AA PAA AA AA 19 Analog INput maa ANNA ATAT NG DADAAN ADA ET 19 Internal Tempera tire sgreing an i a Gan TA 20 Battery Voltage eee 20 DS ial MA PUES eme H Una DAN 21 Digital OUTPUTS 1 ANAN 22 AccelSr omite saa 22 Configuration Button aa E 24 Specifications Intelligent Edge Node Sase eet a aaea i aa aai a ae ane a ae Ee eE a EE A s ETES 25 Radio Specifications e herr Ree KALAN ee Evan EEEE ae eee aea ve Pee ave oe vea da eene rea re iaaa TEA EOE 27 Mechanical Drawing 1o orte MGA MR badekaret ret HER Pet ba Fe ehe a go eerta 29 Model N rmibets reor een ere tede cote even etuer eri va Ven eed de phe vede VF tend ve aed bn dae sues Cose ree veu epa rgo 30 Model Numbers for Wzzar
4. on the device for at least 1 second to wake up Bluetooth radio the LED will come on to signify this 3 Press the device you would like to view This screen lets the user view Bluetooth advertisements from the Nodes 4 Press the Configure Device button 5 Pair with the device Defaults are admin admin 6 Press the Radio Setup button to set the Network ID and Network Join Key These must be the same values that you enter in the corresponding network gateway Press the Save button to save the new settings 7 Refer to the Wzzard Platform App User manual for further node programming instructions Documents can be found at http www bb smartsensing com PH No Fi 14 4 B B amp B ELECTRONICS Device WSD2MA2 Radio Setup Basic See Advanced Settings Network ID 1981 Network Join Key Bluetooth LE Setup Advertise During Sleep m Advertise Rate 0 00 10 Username admin Password 17 CONFIGURING YOUR WZZARD INTELLIGENT EDGE NODES RADIO Configuration Parameter Parameter Default Description Screen Range Value Radio Network ID 1 65534 1981 Unique identifier for the sensor network This ID must match the gateway Join Duty 0 2 99 8 2596 The percent of time that the node will Cycle be awake A higher value allows the node to connect to the gateway faster but uses more battery current Network Join 32 hexa Wzzard 1
5. 1 100 Jep cm wspiCIK 33V J 100 Jep eno fwspaxvo 33v o 4 S f wsoxvo 33v J ol Gn GND GND DO 33REF GND GND GND DO 3 3REF GND Do2 GND GND enD Do2 GND GND GND GND GND GND GND GND GND wsBacri 33v 100 Jep emo WsBiCIK 33V 1 100 Jep Gn enD AIN2 GND DO 33REF GND pot poz eno GND GND 3 3V 3 3V power input 3 3REF 3 3V output reference AIN1 Analog Input H1 AIN2 Analog Input 2 AIN3 Analog Input 3 DO Digital Output DIN1 Digital Input 1 DIN2 Digital Input 42 D01 Digital Output 1 DO2 Digital Output 2 GND Ground Input 10 1 2 3 4 5 6 7 8 White Brown Green Yellow Gray Pink Blue Red enD AIN2 GND DO 33REF GND GND GND DO 33REF GND Do2 GND GND GND p02 GND GND GND GND GND GND GND GND GND GND enD an2 Gno DO 33REF GND DO1 DO2 GND GND GND 3 3V 3 3V power input 3 3REF 3 3V output reference AIN1 Analog Input 1 AIN2 Analog Input 2 AIN3 Analog Input 3 DO Digital Output DIN1 Digital Input 1 DIN2 Digital Input 42 DO1 Digital Output 1 DO2 Digital Output 2 GND Ground Input 11 WIRE COLORS FOR WZZARD INTELLIGENT EDGE NODES WITH BLUETOOTH LE 4 0 eend es om veion ome e me an wseimn J mm tt YY we pp JP p wsi pp PP ws am JP PJ wspicaz pp JPP jwseimoz JP
6. 28 bit encryption key for the network Key decimal Smartworx characters Advertise On Off Enabled Enables sensor broadcast messages over During Sleep the Bluetooth LE interface while the node is asleep Advertise 10 86400 10 Interval between broadcast messages Rate seconds Username 16 admin Login name for configuring the node characters Password 16 admin Password for configuring the node characters DEVICE CONFIGURATION Configuration Parameter Parameter Default Description Screen Range Value Device Configuration Description 0 40 User defined text field characters Exception 0 10 86400 O Determines how frequently the node will based seconds wake up to check for an exception Measurement Interval Publish 10 seconds 60 Determines the interval between publishes Interval to 23 59 59 to the broker hours 18 GEO LOCATION Configuration Parameter Parameter Default Description Screen Range Value Geo Location Latitude 90 to 90 0 0 Geographical location of the sensor degrees Longitude 180 to 180 0 0 Geographical location of the sensor degrees Elevation 999999 9 0 0 Elevation of the sensor to 999999 9 Sensor Label 32 geoloc User defined text field to describe the characters sensor ANALOG INPUTS Configuration Parameter Parameter Default Description Screen Range Value Analog Inputs Sensor Enable On Off On Enables publishing of
7. 8 2 27 2009 Mechanical Shock 50G 11ms FCC Class B Notice this device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation I hereby declare that the products named above meet the essential requirements of and are in conformity with the Standards listed Z Mike Fahrion Date November 20 2014 Director of Product Management Place Ottawa Illinois USA B amp B Electronics 32 DECLARATION OF COMPLIANCE CE B BEB ELECTRONICS Make The Right Corrections Declaration of Conformity The undersigned representing the following supplier B amp B Electronics Manufacturing Company 707 Dayton Road Ottawa Illinois 61350 USA Herewith declare under our sole responsibility Model Numbers WSDxxxx WSBxxxx where xxxx are alphanumeric characters Description Wzzard Intelligent Edge Node Wzzard Basic Edge Node These products are in conformity with the provisions of the following directives when used in accordance with the instructions contained in the product documentation 1999 5 EC Radio and Telecommunications Terminal Equipment R amp TTE Directive 2011 65 EU Reduction of Hazardous Substances Directive The standards referenced below have
8. On When enabled the node will broadcast Advertisemen the sensor value over the Bluetooth t Enable interface Acceleromete 2G 4G 8G 4G Measurement range of the 22 r Granularity accelerometer A lower value will increase the sensitivity of the accelerometer Acceleromete 12 5 25 100Hz Frequency Response of the r Interval 50 100 accelerometer A higher value will allow 200 400Hz the accelerometer to capture faster events Output increases with acceleration in the direction of the arrows X Left Right gt B Wzzarcl Y hd Forward Back Configuration Status Z Up Down 23 CONFIGURATION BUTTON When you press and hold the Configuration button on the Node for more than 5 seconds it will LED will flash quickly a couple times Restore the BLE login and password encryption key encryption enable Restartthe device This action will not reset the device back to factory settings When you press and hold the Configuration button on the node for at least 1 second but less than 5 seconds it will LED will turn on hold button until LED is seen will Wake up the device and turn on the BLE radio This will enable the Wzzard APP to communicate to the node onfiguration Status 24 SPECIFICATIONS INTELLIGENT EDGE NODES Power Supply Sources External Input 3 3 VDC 596 Voltage Connectors M12 1 2 Condui
9. Wzzard Sensing Platform Intelligent Edge Nodes Operation Manual EB SMARTWSRX B B SMARTWISRX International Headquarters B amp B Electronics Mfg Co Inc 707 Dayton Road Ottawa IL 61350 USA Phone 815 433 5100 General Fax 815 433 5105 Website www bb elec com support bb elec com European Headquarters B amp B Electronics Westlink Commercial Park Oranmore Co Galway Ireland Phone 4353 91 792444 Fax 353 91 792445 Website www bb europe com techsupport bb elec com Document Wizard User Manual RO 5014m MUI IRE E 5 ABout the Wzzard Sensing PlatfOlkm iius oreet te KANA sos san ING sedexsabusdevebusesvasexdedaneoneesassviesbensts eetcassadebard 6 Wireless Connectivity Where You Need It rusnnnnnnrnnnnvnnenvnnnnrnnenvnnsnrnnenvnnsnrnnenvnnsnrnsenvnnsnrnnenvnnsnrnsenvnnenvnsenennsnrnssneene 6 Contents of Pakabos 8 Hardware Dose E ton PL RID AA NAAN ARALAN ANAN a M 9 Connecting Your SENSO ask E 9 Connecting Your Sensor with Conduit models Analog and Digital areranvvnrrrrnonnnnvrrrnannnnerrrnennnnerrrnennnnerrrnenvnnenr 9 Connecting Your Sensor with M12 Models Analog and Digital 13 Terminal Block Connections Thermocouple eese nennen GANANG ener nennen nest nente nente nente nennen 14 Powering Your Wzzard Edge Node sesssessseesesesee eene KG enne AN
10. als to the broker Alert Low 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker BLE On Off On When enabled the node will broadcast the Advertisement sensor value over the Bluetooth interface Enable DIGITAL INPUTS Configuration Parameter Parameter Default Description Screen Range Value Digital Inputs Sensor Enable On Off On Enables publishing of the sensor data to the broker Sensor Label 32 din1 User defined text field to describe the characters sensor Measurement 8 characters Engineering unit of measure Unit Digital Input Boolean Boolean The type of sensor connected to the input Type Count Rate either a boolean input a counter totalizer or a rate meter Enable On Off On Enables publishing of the sensor data to Exception the broker when an alert level is reached Alert High 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker Alert Low 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker Invert Input On Off Off Changes the input from an active high input to an active low input BLE On Off On When enabled t
11. anty or the remainder of the initial warranty period whichever is longer To receive in warranty service the defective product must be received at B amp B Electronics no later than the end of the warranty period The product must be accompanied by proof of purchase satisfactory to B amp B Electronics denoting product serial number and purchase date a written description of the defect and a Return Merchandise Authorization RMA number issued by B amp B Electronics No products will be accepted by B amp B Electronics which do not have an RMA number For an RMA number contact B amp B Electronics at PHONE 800 624 1070 in the U S and Canada or 949 465 3000 or FAX 949 465 3020 The end user shall return the defective product to B amp B Electronics freight customs and handling charges prepaid End user agrees to accept all liability for loss of or damages to the returned product during shipment B amp B Electronics shall repair or replace the returned product at its option and return the repaired or new product to the end user freight prepaid via method to be determined by B amp B Electronics B amp B Electronics shall not be liable for any costs of procurement of substitute goods loss of profits or any incidental consequential and or special damages of any kind resulting from a breach of any applicable express or implied warranty breach of any obligation arising from breach of warranty or otherwise with respect to the manufacture and sal
12. been applied EMC EN55022 2010 AC 2011 Information technology equipment Radio disturbance characteristics Limits and methods of measurement EN55024 2010 Information Technology Equipment Immunity Characteristics Limits and methods of measurement EN61000 4 2 2009 ESD Immunity EN61000 4 3 2006 A2 2010 4 Radiated Immunity EN61000 4 4 2012 EFT Burst Immunity EN61000 4 5 2006 Surge Immunity EN61000 4 6 2009 RF Conducted Immunity The authorized representative located within the community maintains a copy of the technical documentation required by the directives B amp B Electronics Westlink Commercial Park Oranmore Co Galway Ireland Phone 353 91 792444 Email eSales bb elec com I hereby declare that the product named above meets the essential requirements of is in conformity with and the CE mark has been applied according to the relevant European directives listed above using the relevant sections of the European Standards and other normative documents listed above 7 a Pan Mike Fahrio Date November 20 2014 Director of Product Management Place Ottawa lllinois USA B amp B Electronics B amp B ELECTRONICS TECHNICAL SUPPORT Phone 1 800 346 3119 Monday Friday 7 a m to 7 p m CST Fax 815 433 5109E Mail Email support bb elec com Web www bb elec com 34
13. d Intelligent Edge Nodes with SmartMesh IP and Bluetooth LE 30 Model Numbers for Wzzard Intelligent Edge Nodes with Bluetooth LE rarorrrnrrrnnonnnnrvrnrnnsnonnnnrrnnrnnsnnnsnnrsnnsnn 31 Model Numbers for Spectre Network GatewayS ccccccccccsssssssecececeesessseesecececseeeaeseescesseseeaeseescesseseaaeseeeessseseaaees 31 Declaration of Compliance uns enn reote Ex Reb NAUNA nang knr NIN IKINADENA 32 Declaration ot CompliarniCe GE eee oer are AG Er 33 B amp B Electronics Technical Support aaa aa 34 WARRANTY B amp B Electronics warrants to the original end user purchaser that this product EXCLUSIVE OF SOFTWARE shall be free from defects in materials and workmanship under normal and proper use in accordance with B amp B Electronics instructions and directions for a period of six 6 years after the original date of purchase This warranty is subject to the limitations set forth below At its option B amp B Electronics will repair or replace at no charge the product which proves to be defective within such warranty period This limited warranty shall not apply if the B amp B Electronics product has been damaged by unreasonable use accident negligence service or modification by anyone other than an authorized B amp B Electronics Service Technician or by any other causes unrelated to defective materials or workmanship Any replaced or repaired products or parts carry a ninety 90 day warr
14. e of any B amp B Electronics product whether or not B amp B Electronics has been advised of the possibility of such loss or damage EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE B amp B ELECTRONICS MAKES NO OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED WITH RESPECT TO THIS B amp B ELECTRONICS PRODUCT INCLUDING WITHOUT LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED B amp B ELECTRONICS SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON INCLUDING EMPLOYEES DISTRIBUTORS RESELLERS OR DEALERS OF B amp B ELECTRONICS WHICH ARE INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE EXPRESS WARRANTY STATED ABOVE Every reasonable effort has been made to ensure that B amp B Electronics product manuals and promotional materials accurately describe B amp B Electronics product specifications and capabilities at the time of publication However because of ongoing improvements and updating of B amp B Electronics products B amp B Electronics cannot guarantee the accuracy of printed materials after the date of publication and disclaims liability for changes errors or omissions ABOUT THE WZZARD SENSING PLATFORM WIRELESS CONNECTIVITY WHERE YOU NEED IT The Wzzard intelligent wireless sensor platform makes it quick and easy to connect sensors and communicate their data to your appl
15. eless Mesh 802 15 4e 2 Thermocouple J type inputs 1 Digital Output External Antenna WSD2CT PEDER s P Conduit Connector Wireless Mesh 802 15 4e 2 Thermocouple J type inputs 1 Digital Output Internal Antenna WSDA1CTJ PEE E Conduit Connector Wireless Mesh 802 15 4e 2 Thermocouple K type inputs 1 Digital Output External Antenna WSD2CTK i BE RRR Conduit Connector Wireless Mesh 802 15 4e 2 Thermocouple K type inputs 1 Digital Output Internal Antenna WSD1CTK aui i Conduit Connector Model Number WSD2XVO WSD1XVO Model Number Wireless Mesh 802 15 4e 2 Analog Inputs 1 Digital Output External Antenna M12 WSD2MA2 Connector di WSD1MA2 Wireless Mesh 802 15 4e 2 Analog Inputs 1 Digital Output Internal Antenna M12 Connector Wireless Mesh 802 15 4e 2 Analog Inputs 1 Digital Output External Antenna Conduit WSD2CA2 Enp Ni Connector Wireless Mesh 802 15 4e 2 Analog Inputs 1 Digital Output Internal Antenna Conduit WSD1CA2 Connector aid i WSD2MA3 WSD1MA3 WSD2CA3 WSD1CA3 Model Number Wireless Mesh 802 15 4e 2 Digital Inputs 2 Digital Outputs External Antenna M12 WSD2MD2 BEP 5 n Connector Wireless Mesh 802 15 4e 2 Digital Inputs 2 Digital Outputs Internal Antenna M12 WSD1MD2 pr g 2 Connector Wireless Mesh 802 15 4e 2 Digital Inputs 2 Digital Outputs External Antenna Conduit WSD2CD2 Connector i i i WSD1CD2 Wireless Mesh 802 15 4e 3 Analog Inputs Internal Antenna Condu
16. he node will broadcast the Advertisement sensor value over the Bluetooth interface 21 Enable True Message 8 characters Message that is displayed when the boolean input is true False Message 8 characters Message that is displayed when the boolean input is false Minimum On seconds The minimum amount of time that the Time input signal must be low or high before it is registered as a valid pulse Period seconds 1 Update frequency for the rate meter Multiplier 999999 9 1 The scale factor for the counter and rate to 999999 9 meter DIGITAL OUTPUTS Configuration Parameter Parameter Default Description Screen Range Value Digital Outputs Sensor Enable On Off On Enables publishing of the sensor data to the broker Sensor Label 32 do1 User defined text field to describe the characters sensor Invert Output On Off Off Inverts the level of the output BLE On Off On When enabled the node will broadcast the Advertisement sensor value over the Bluetooth interface Enable ACCELEROMETER Configuration Parameter Parameter Default Description Screen Range Value Accelerometer Sensor Enable On Off On Enables publishing of the sensor data to the broker Sensor Label 32 accel1 User defined text field to describe the characters sensor Measurement 8 G Engineering unit of measure Unit characters BLE On Off
17. ication on your network or on the Internet for visualization analytics or integration into business applications The Wzzard platform connects to a vast range of industry standard sensors It uses Intelligent Edge Nodes and a wireless SmartMesh IP network to transmit sensor data to the Spectre Network Gateway The Spectre Network Gateway can connect to the Internet via wired connections or the cellular data network Wzzard Intelligent Edge Nodes accommodate external sensors with a wide variety of sensor interface options including general purpose analog inputs digital input output and thermocouple They can also contain internal sensors like an accelerometer depending upon the model number Secure Reliable and Highly Scalable Wireless Networking The Wzzard platform uses 802 15 4e wireless SmartMesh IP networking technology to deliver reliable resilient and scalable communication with advanced network management and comprehensive security features The platform uses full SmartMesh IP networking and time synchronized channel hopping to provide up to 99 999 connectivity even in the most demanding RF environments The Wzzard wireless sensor platform enables rapid network deployment and expansion New nodes may be added at any time and the SmartMesh network dynamically self configures as new nodes are added or removed This process is a function of the mesh network itself and does not need to be controlled by the network gateway Easy Config
18. ined text field to describe the characters sensor Measurement Cel degF C Engineering unit of measure Unit Enable On Off On Enables publishing of the sensor data to Exception the broker when an alert level is reached Alert High 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker Alert Low 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker BLE On Off On When enabled the node will broadcast the Advertisement sensor value over the Bluetooth interface Enable BATTERY VOLTAGE Configuration Parameter Parameter Default Description Screen Range Value Battery Voltage Sensor Enable On Off On Enables publishing of the sensor data to the broker Sensor Label 32 vbatt User defined text field to describe the characters sensor Measurement Volts V Engineering unit of measure Unit 20 Enable On Off On Enables publishing of the sensor data to Exception the broker when an alert level is reached Alert High 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute interv
19. it Connector 30 MODEL NUMBERS FOR WZZARD INTELLIGENT EDGE NODES WITH BLUETOOTH LE Wzzard Intelligent Edge Nodes with Bluetooth LE Model Number Temperature WSBA1CTJ Bluetooth 2 Thermocouple J type inputs 1 Digital Output Conduit Connector WSB1CTK Bluetooth 2 Thermocouple K type inputs 1 Digital Output Conduit Connector Model Number Analog WSB1MA2 Bluetooth 2 Analog Inputs 1 Digital Output M12 Connector WSB1CA2 Bluetooth 2 Analog Inputs 1 Digital Output Conduit Connector Model Number Digital WSB1MD2 Bluetooth 2 Digital Inputs 2 Digital Outputs M12 Connector WSB1CD2 Bluetooth 2 Digital Inputs 2 Digital Outputs Conduit Connector MODEL NUMBERS FOR SPECTRE NETWORK GATEWAYS Spectre Network Gateway Models ERT351 Ethernet Network Gateway with 2 Ethernet ports wireless mesh 802 15 4e RT3G 350 Cellular Ethernet Network Gateway with 1 Ethernet port wireless mesh 802 15 4e RT3G 351 Cellular Ethernet Network Gateway with 2 Ethernet ports wireless mesh 802 15 4e RT3G 352 Cellular Ethernet Network Gateway with 1 Ethernet port 1 RS 232 port wireless mesh 802 15 4e RT3G 354 Cellular Ethernet Network Gateway with 1 Ethernet port 1 RS 485 port wireless mesh 802 15 4e 31 DECLARATION OF COMPLIANCE B BsB ELECTRONICS Make The Right Connections Declaration of Compliance The undersigned representing the following supplier B am
20. p B Electronics Manufacturing Company 707 Dayton Road Ottawa Illinois 61350 USA Herewith declare under our sole responsibility Mode Numbers WSDxxxx WSBxxxx where xxxx are alphanumeric characters Description Wzzard Intelligent Edge Node Wzzard Basic Edge Node The standards referenced below have been applied EMC EN 61000 6 2 2005 Immunity standard for industrial environments EN 61000 6 4 2007 Emission standard for industrial environments FCC Part 15 CFR Title 47 2014 ICES 003 2012 Digital Apparatus Industry Canada EN 61326 1 2012 Electrical equipment for measurement control and laboratory use EMC requirements EN 55022 2010 AC 2011 Information technology equipment Radio disturbance characteristics Limits and methods of measurement CISPR 22 Ed 6 0b 2008 Information technology equipment Radio disturbance characteristics Limits and methods of measurement EN 55024 2010 Information Technology Equipment Immunity Characteristics Limits and methods of measurement CISPR 24 2013 Information Technology Equipment Immunity Characteristics Limits and methods of measurement IEC EN 61000 4 2 2009 ESD Immunity IEC EN 61000 4 3 2006 A2 2010 Radiated Immunity IEC EN 61000 4 4 2012 EFT Burst Immunity IEC 61000 4 5 2005 Surge Immunity EN 61000 4 5 2006 Surge Immunity IEC EN 61000 4 6 2009 RF Conducted Immunity Environmental EN60068 2 6 2008 Mechanical Vibration 2G 0 012in displacement 10 500 Hz EN6006
21. quence Spread Spectrum DSSS Raw Data Rate 250 kbps Range 25 C 50 RH 2dBi Omni m Directional Antenna Antenna 2 m Indoor 100 Outdoor 300 Free Space 1200 Receiver Packet Data Error Rate PER 196 93 dBm Sensitivity Receiver PER 50 95 dBm Sensitivity Output Power Delivered to a 50 O load High Calibration 8 dBm Setting Low Calibration 0 dBm Setting 27 BLUETOOTH LE RADIO SPECIFICATIONS No Characteristics Conditions Min Typ Max Units 1 Operation Frequency 2402 2480 MHz Range 2 Channel Spacing 2 MHz 3 Output Power Maximum setting measured 4 dBm at single ended 500hm Minimum setting measured 24 dBm at single ended 500hm 4 Sensitivity High Gain High Gain Mode 93 0 70 dBm Mode Standard Mode 92 5 70 dBm THIONYL CHLORIDE LITHIUM BATTERIES 2 SUPPLIED WITH PRODUCT Characteristics Conditions Temperature Range 40 to 85 C Nominal Capacity 2 4 Ah Nominal Voltage 3 6V Diameter 14 5 mm Height 50 5 mm Potential hazard Do not recharge crush disassemble or heat above 212 F 100 C 28 MECHANICAL DRAWING 95 25 53 75 5 59 4X 5 22 65 15 2 57 Figure 1 Mechanical drawing MODEL NUMBERS MODEL NUMBERS FOR WZZARD INTELLIGENT EDGE NODES WITH SMARTMESH IP AND BLUETOOTH LE Wzzard Intelligent Edge Nodes with SmartMesh IP and Bluetooth LE Model Number Wir
22. s waste collection site an e waste disposal center or other facility qualified to accept lithium batteries LEDS After you have installed the batteries the LED will begin to blink This indicates that the Node is attempting to establish a network connection The LED will cease blinking when a connection is made Status LED Data Solid On Module startup initialization approx 10 sec Slow Blink Attempting to establish connection with SmartMesh IP network 1 sec on 1 sec off Fast Blink Firmware Update in progress 10 blinks per sec OFF Unit is connected to wireless network 15 MOUNT YOUR WZZARD EDGE NODE Wzzard nodes may be mounted either with screws or with their internal magnets Flange Mounting Magnetic Mounting Wzzard nodes may be mounted via their Wzzard nodes contain a powerful internal mounting ears M5 10 mounting magnet Pull force 4 7 lbs 2 13 kg The magnet is in the base of the Wzzard node 16 CONNECTING TO YOUR INTELLIGENT EDGE NODES VIA BLUETOOTH LE INSTALL THE WZZARD APP ON YOUR HANDHELD DEVICE You may Install the Wzzard app on your Android or IOS handheld device Your handheld device must be compatible with Bluetooth LE 4 0 The Android APP version is available on Playstore The los APP version is here on Apple App Store iTunes The APP can also be downloaded from http www bb smartsensing com xxxxxxxx 1 Open the Wzzard App 2 Press the Configuration button
23. so has an auxiliary port that can be configured for other purposes like Ethernet or RS 232 485 422 Secure Connections To ensure secure communications the Spectre Network Gateway supports the creation of VPN tunnels using IPsec OpenVPN and L2TP The web interface provides detailed statistics about gateway activities signal strength etc The gateway supports DHCP NAT NAT T DynDNS NTP VRRP control by SMS and many other routing functions The Spectre Network Gateway also provides diagnostic functions which include automatically monitoring the PPP connection automatic restart in case of connection losses and a hardware watchdog that monitors the Spectre Network Gateway status CONTENTS OF PACKAGE The package includes Wzzard Intelligent Edge Node Sensor wire harness cable conduit connection models only 2 3 6V AA Thionyl Chloride Lithium Batteries External Antenna some models Quick Start Guide HARDWARE INSTALLATION CONNECTING YOUR SENSOR CONNECTING YOUR SENSOR WITH CONDUIT MODELS ANALOG AND DIGITAL Thread the wire harness through the conduit Plug the included wire harness into the receptacle on the circuit board inside the node Connect your sensor to the wires running from the node s conduit Consult the charts below for wire colors and connections 1 2 3 4 5 6 7 8 Brown Red Pink Yellow Green Blue White Gray wspcu 33v J 100 Jep eno wspicn 33v 1 Jo Jep Gn wspactk 33V
24. t sensor interface cable included 8 wire 26 gage 6 ft Battery Life Multiple years based on 1 min sensor sampling and reporting Environmental Intended for indoor and outdoor use Operating 40 to 80 9C Temperature Storage Temperature 40 to 859C Operating Humidity 0 to 95 non condensing LED indicators One Green LED Data Color Green Blink Attempting to establish network connection Off Device connected to network Enclosure Rating Rating IP66 rated fiber reinforced polyester PBT Mounting Mountable by use of magnets or mounting ears Certifications FC FCC Part 15 Class A FCC Part 15 247 Industry Canada RSS210 CSA Class 1 Div 2 Groups A B C D ANSI UL equivalent CE EN55022 CISPR EN55022 Class A EN61000 6 1 Generic Standards for Residential Commercial amp Light Industrial EN61000 6 2 Radiated immunity 10 V m 80 2700 MHz EN61000 6 2 or Equivalent EN61000 4 2 ESD 15kV contact AkV air EN61000 4 3 RFI EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CI EN61000 4 6 Power Frequency Magnetic EN61000 4 11 Voltage Dips amp Interruptions EN60255 21 1 Vibration EN60255 21 2 Shock IEC Shock and IEC 60068 2 27 2008 shock 50g 11ms half sine wave 18 shocks Vibration IEC 60068 2 6 2007 vibration 2g 10 500 Hz 1 5mm displacement Radiated immunity 10 V m 80 2700 MHz EN61000 6 2 or Equivalent FCC FCC Part 15 Class A FCC Part 15 247 25 Industry Canada RSS210
25. the Gateway is using the cellular data network Thanks to low power wireless technology and programmable time synchronization the Intelligent Edge Nodes can operate for up to five years on just two AA lithium batteries The Spectre Network Gateway The Spectre Network Gateway connects to the SmartMesh IP wireless mesh network and the Wzzard Intelligent End nodes through an integrated 802 15 4e radio The Spectre Network Gateway receives the incoming data stream from edge nodes in MQTT SN format and converts the information into MQTT protocol for transport to an MQTT broker on your network or on the Internet Uniquely designed with open source LINUX architecture the Spectre Network Gateway is customizable through installation of software plug in modules Users can create their own plug in modules with common LINUX commands and scripts or add them from B amp B s existing library Plug in modules are available for establishing communications with the MQTT broker within a number of loT application platform providers including Axeda Xivley ILS and SeeControl The Spectre Network Gateway is built for plug and play simplicity with extensive remote management deployment and customization options It connects Ethernet equipment and other devices to the Internet or intranet via either cellular 3G or 10 100 wired Ethernet The standard configuration includes a 10 100 Ethernet port USB host port binary input output I O port and an 802 15 4e radio It al
26. the sensor data to the broker Analog Input 0 20mA 4 0 5V The type of sensor connected to the input Type 20mA 0 5V 1 5V Sensor Label 32 ain1 User defined text field to describe the characters sensor Measurement 8 characters Engineering unit of measure Unit Sensor Span 999999 9 5 0 The value that is reported when the input Point to 999999 9 is at the maximum value Sensor Zero 999999 9 0 0 The value that is reported when the input Point to 999999 9 is at the minimum value Enable On Off On Enables publishing of the sensor data to Exception the broker when an alert level is reached Alert High 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker Alert Low 999999 9 The node will initially send an update to to 999999 9 the broker when the input exceeds this value The node will subsequently send 5 more updates at 1 minute intervals to the broker 19 BLE On Off On When enabled the node will broadcast the Advertisement sensor value over the Bluetooth interface Enable INTERNAL TEMPERATURE Configuration Parameter Parameter Default Description Screen Range Value Internal Temperature Sensor Enable On Off On Enables publishing of the sensor data to the broker Sensor Label 32 temp1 User def
27. uration and Installation Configuration of the Wzzard sensor platform is easy via iOS or Android smart phones or tablets Using the Wzzard app your handheld devices can configure the Wzzard Intelligent Edge Nodes over their Bluetooth LE connections The intelligent edge nodes can be configured with calibration and scaling information eng units friendly names geolocation and other descriptive information The MQTT SN protocol is used to transport sensor data to the network gateway MQTT SN is a highly efficient publish subscribe protocol optimized for sending sensor data over wireless networks The platform simplifies physical installation as well The Wzzard Intelligent Edge Nodes can be attached to any surface using screws or their embedded magnetic bases The IP67 rated fiber reinforced polyester PBT housing and the ability to connect to external sensors via conduit fitting cable gland or M12 connector make the units deployable in virtually any industrial or commercial environment Intelligence at the Network Edge The Wzzard wireless platform places intelligence at the network edge The Wzzard Intelligent Edge Nodes can be configured to communicate data only when specified threshold or alert levels are exceeded When reporting they can associate useful information like geo location device name and uptime This eliminates unnecessary network traffic eases the processing burden on upstream resources and cuts the cost of cellular data plans when
Download Pdf Manuals
Related Search