Quick-Start Guide - Emerson Network Power
Contents
1. EMERSON LIEBERT RDU S RACK MANAGEMENT DEVICE Quick Start Guide The Liebert RDU S is a compact rack processing unit designed to monitor the environment in electronic equipment racks and rooms through various types of sensors and cameras The unit can accommodate multiple sensors such as temperature humidity water smoke motion and door sensors It can also be used for remote notification such as activating a beacon light to report problems The compact design makes it suitable for installation in a rack where it takes up little space or it may be mounted on a wall for access without opening the equipment rack 1 0 PORTS AND INDICATORS Figure 1 shows the front panel of the Liebert RDU S The ports and their functions are listed in Table 1 Figure 1 Ports and indicators on front of unit STATUS INDICATORS Ground Micro SD RJ45 sensor connector ports DO1 DO2 card slot outputs Power Alarm FRONT OF UNIT L Ethernet Relay i output ort Power ports 42VDC USB ports input output Status eS indicators Table 1 Port descriptions RMB sensorpons OOo RJ45 sensor ports ees Connect digital sensors one sensor per port on off dry contact sensors PARUE DONS pee such as smoke detectors and motion detectors Liebert SN ports Connect Liebert SN sensors for temperature humidity and other conditions See Section 3 0 for details on connecting sensors to RJ45 sensor ports excluding Ethernet2. into the Ethernet port on the front panel of the Liebert RDU S shown at right Insert the other end of the cable into a laptop s Ethernet port Ethernet port 3 Liebert RDU S If needed configure the laptop s IP settings to communicate on a 192 168 0 X network for example IP address 192 168 0 9 Subnet mask 255 255 255 0 Default gateway 192 168 0 1 2 Open a browser and go to the login page Open a Web browser such as Microsoft Windows Internet Explorer Liebert rpu s Performance Monitoring 3 Login to the Web interface e Enter the IP address of the Liebert RDU S in the address bar the default is http 192 168 0 10 The login window appears shown at right at Liebert RDU S Language English lvl User Name admin e Select a user name from the drop down list and enter a password both case sensitive then click the Login but ton e User Name default is admin e Password default is Liebert R 4 Click the Configure tab then click Network at left Password eeeeee NOTE For security change the default password see the user manual SL 31310 A N EMERSON Network Powe RDU S Network User admin logout User level Administrator RDU S System Time 2010 06 20 17 46 09 RDU S IP Address 126 4 203 229 Obtain IP address automatically Use the following IP address IP Address 126 4 203 229 Subnet Mask 255 255 255 0 Default Gateway 126 4
3. 203 5 Configure Determine which method to use for IP address assignment DHCP automatic or Static fixed address e For DHCP click the Obtain IP address automatically button To assign a Static IP address click Use the following IP address then enter the appropriate IP address subnet x mask and gateway address for example You must reboot ROU 5S to effect the change Click Apply to save any changes sr A confirmation window indicates the unit must be rebooted for the change to take effect Click OK and the unit will reboot If needed reset the laptop s IP settings as before Step 1 re you sure you want bo submit the changes Cancel Liebert Corporation 1050 Dearborn Drive Telephone 1 800 877 9222 P O Box 29186 Facsimile 1 614 841 6022 Columbus OH 43229 www liebert com 2010 Liebert Corporation All rights reserved throughout the world Specifications subject to change without notice S EMERSON Network Power Liebert is a registered trademark of Liebert Corporation All names referred to are trademarks or registered trademarks of their respective owners SL 31305_REV4_06 13
4. e to connect to one of the Liebert SN ports on the Liebert RDU S You may use this cable or another standard straight through cable Liebert SN ports To connect the sensor Connect i Insert either end of an RJ45 connector on the factory supplied RJ45 ah ue RJ45 cable or user supplied cable into the Liebert SN port on the cable toa Liebert RDU S identified by the icon shown below ca SN er Connect eon Description Purpose oon Liebert SN Use these ports ONLY to sensor ports for Liebert SN sensors e Connect the other end of the cable to the sensor Liebert RDU S 2 4 0 JAVA CONFIGURATION SETTINGS FOR LIEBERT RDU S Before logging into the Liebert RDU S Web pages verify that Java Version 1 7 Update 21 is installed on your computer 1 Open the Java Control Panel from the Control Panel 2 On the Start Menu enter Java in the search option This will display the Java Control Panel 3 Launch the Java 82 bit application 4 Select the About button This will display the version information Verify that Version 7 Update 21 or greater is installed If the Java version on the computer is older than Version 7 Java must be updated before continuing L Java Control Panel About About View version information about Java Control Panel Button Network settings are used when making Internet connections By default Java wall use the network settings in your web browser Only advanced users should modif
5. ny equipment For horizontal mounting in a rack use the factory supplied brackets and screws M3 and M6 1 Place the shorter side of a bracket flush with the front panel and the longer side against one side of the unit shown below left 2 Align the rear bracket hole with a mounting hole on the unit shown below left and use an M3 screw to fasten the bracket to the side of the unit Mounting hole for rack mounting Unit with both side brackets attached Bracket flush with front of unit 3 Repeat Steps 1 and 2 for the bracket on the other side The Liebert RDU S with both brackets attached is shown above right 4 Use M6 screws to fasten both brackets of the Liebert RDU S onto the rack s front or rear rails Refer to the user manual for other mounting options e Wall mounting with factory supplied brackets and screws e Vertical mounting in a rack with an optional round hanger available separately 3 0 CONNECTING TO SENSOR PORTS For sensor ports follow these guidelines and see the Liebert RDU S user manual SL 31310 3 1 Digital Input Ports DI1 DI2 DI3 The three digital input ports DI1 DI2 and DI3 shown at right may be used to connect digital sensors such as smoke detectors and motion detectors Digital input f 3 2 Liebert SN Sensor Ports ports lt The two ports labeled with a Liebert SN icon 8 shown at right are Dia E designed for use with Liebert SN sensors Each sensor is shipped with a cabl
6. port Status Indicators Refer to Table 2 for details on the unit s status indicators relay outputs power alarm and run Table 2 Indicator descriptions Indicator Status of Color Status Indicator On Flashing Status Indicator Off DO1 DO2 Relay outputs Relay DO1 or DO2 is closed Relay DO1 or DO2 is open POWER Input power Input power is present Input power is not present On Solid Unit has a critical alarm ALARM Alarms So Off No alarms detected Flashing Flashing Unit has a warning alarm Unit operation Flashing Unit is operating normally Off Unit is not running 1 Liebert RDU S 2 0 MOUNTING THE UNIT WARNING Ensure that the Liebert RDU S is Off and that all local and remote input power sources have been disconnected before beginning to install the unit Never open alter or move the unit while input power is present NOTE All external circuits must be safety extra low voltage SELV circuits The insulation and isolation must be enhanced between the SELV circuits and the power grid Mount the Liebert RDU S securely before connecting equipment typically in a 19 rack or mounted on a wall The Liebert RDU S must be installed near a power outlet or socket within easy reach using the supplied power cord e The unit must be connected to the power outlet or socket with protective earthing terminal e The unit must be securely installed in a rack or on a wall BEFORE using or connecting a
7. y these se tings Standard Edition Temporary Internet Files Java Version Fies you use in Java applications are stoned in a speda folder for quick execution later Only advanced users should delete files or modify these settings sete tee Javan the browser iz enabled See the Security tab 5 Under the Security tab of the Java Control Panel set the Security Level to Medium General Update Jafa Security advpnced Security l Ee Tava content n te Browser Level Security Security Level Slider Tab 3 Do not start console Default Jawa for browsers Disable the Java eae Devterret Ex e Plug in option by removi ng the Enable the next generation Java Plugin requires browser restart check mark from aa iae as the box Always allow if hinted Prompt user Promot user if hinted HLF File MIME Association a 6 Click the Apply button to accept the changes 7 Under the Advanced tab disable uncheck the Java Plug in option 8 Click the Apply button to accept the changes and close the Java Control Panel Follow the subsequent instructions for logging into the Liebert RDU S 5 0 SETTING THE IP ADDRESS Follow these instructions to set the IP address of the Liebert RDU S This step is required for communication with the Liebert RDU S using the Web interface 1 Connect a laptop and set its IP address Insert a standard Ethernet cable not included
Download Pdf Manuals
Related Search