Roboto Manual - Starlight Entertainment
Contents
1. without any change after 8 seconds To go back to the functions without any change press the MENU button again Show 1 mode Fixture is placed on the floor Tilt movement angle 210 wy wm Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 wn an Lio im Show 3 mode Fixture is placed on the speaker The spot is always projecting to the audience s direction i e in front of the stage Pan movement angel left to right to left 160 90 horizon Tilt movement angel 60 above horizon 30 below y j 35 H Show 4 mode Fixture is fixed under ceiling The spot is mainly projecting in front of the stage Pan movement angel left to right to left 160 Tilt movement angel 90 vertically front 75 back 15 j 1 _ L tlt slave Mode Press the MENU button up to when the Sitid is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP bution to select the normal or 2L E 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again O a D L a Press the MENU button up to when the bLiid is showing on the display Pressing ENTER button and the display will blink2. thr is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Reset Press the MENU button up to when the is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again Q 4 2 Main Function To select any of the pre set functions press the MENU button up to when the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are shown below Addr i Sig Gh i Ghlid Gh g Gh d Gh H oi fd SL i SLI ic bLiid 4 bo n bo Lifid No SL I PAn MENU noa i i tLt noa i idii noa i
3. LEd dor Qn UFF FAdd tet FhrS rSePt Press the MENU button up to when the I d9F dSF DMX512 Address Setting Show mode 1 Show mode 2 Show mode 3 Show mode 4 Slave Mode Normal Slave mode 2 Light Show Blackout Mode Yes Blackout Blackout Mode No Blackout Normal Color Split Color Pan Normal Pan Inversion Tilt Normal Tilt Inversion Dimmer Normal Dimmer Inversion LED on LED off Display Normal Display Inversion Focus Adjust Self Test Fixture Hours Reset DMX512 Address Setting Addr is showing on the display Pressing ENTER bution and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again Lm Perey Show Mode Press the MENU button up to when the ghno is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the Sh i show 1 or Sh e show 2 or Shi 3 show 3 or 5h H show 4 mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions
4. Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit The unit is designed for use with the HTI 150W Do not use any other type of lamp It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized
5. EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN 60598 1 2004 IEC 60598 1 2003 corrigendum 2004 Part 1 General requirements and test Following the provisions of the low voltage directive 73 23 EEC and 93 68 EEC H If The pan belt is broken Turn off the main power Unscrew all the screws A and open the base housing cover B Unplug all the connect wires C that from the arm to PC board and igniter Unscrew the screws D that fix the bridge E Unscrew the screws F that fix the axis gear G Ooo A Ww N Change a new belt H by going through all connecting wires that from the arm to base and through the bridge for correct position 7 Set up the gear axis to the bridge and screwed it Note do not press the belt 8 Put the belt around the axis gear and motor gear 9 Plug all the connect wires C that form the arm to PC board and igniter 10 Adjust the pan home position 11 Screw the base housing cover B 1 Safety Instruction Please read carefully the instruction which includes important A N information about the installation usage and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet
6. Pressing ENTER button and the display will blink Use DOWN and UP button to select the O0 tilt inversion mode Once the mode has been selected press the ENTER buiton to setup or automatically return to the main functions without any change after 8 seconds To go mT normal or back to the functions without any change press the MENU button again olin Dimmer Inversion Press the MENU button up to when the idi button and the display will blink Use DOWN and UP button to select the O0 i dimmer inversion mode Once the mode has been selected press the ENTER is shown on the display Pressing ENTER normal or button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again I LEO Press the MENU button up to when the LEd is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the TE UFF Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go Led Display Led on or back to the functions without any change press the MENU button again
7. 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function You can select blackout mode BL lid in 4 od yes blackout or A bo no blackout mode while the unit is turned on By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to select an show 1 or Sh c show 2 or SH 3 show 3 or SA H show 4 mode by easy controller Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and DiI r sound LED will flash to the music The other units will have to set in slave mode ILUG and select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will constantly on 2 light show z i l In Quid slave mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 5 2 Easy Controller The easy remote controller is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote cont
8. Use DOWN and UP button to select the yes blackout or N bo no blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after Blackout Mode 8 seconds To go back to the functions without any change press the MENU button again 10 Color Mode Press the MENU button up to when the LENO is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the O0 o 2L split color mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go normal or back to the functions without any change press the MENU button again i PAn Press the MENU button up to when the I PAn is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the OG pan inversion mode Once the mode has been selected press the ENTER button Pan Inversion normal or to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again a LL Tilt Inversion Press the MENU button up to when the i CLC js showing on the display
9. Technical Specifications AC 120V 60Hz or AC 230 240 250V 50 60Hz 20mm Glass T6 3A Fast Blow 373mm x 295mm x 451 mm Weight 13 kg Innovation Quality Performance Z Solution Your integrated Solution LINKABLE IH9000 1 User Guide Professional Entertainment Technology TABLE OF CONTENTS Safety Instruction Technical Specification 2 1 Inserting Exchanging rotating gobos 2 2 Beam angel Lamp How To Set The Unit 4 1 Control Panel 4 2 Main Function How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 iSolution Operation Universal DMX Controller 5 4 DMX512 Configuration 5 5 DMX512 Connection Troubleshooting Fixture Cleaning 7 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility
10. ctions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units DMX address can be setting remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain tL EE eS 4 How To Set The Unit 4 1 Control Panel Display To show the various menus and the selected functions On MENU To select the programming functions DOWN To go backward in the selected functions LED Button By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode Sensitivity To adjust the sound sensitivity Microphone To receive audio signal for sound activation DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together DMX input present UP To go forward in the selected functions ENTER To confirm the selected functions Remote controller input 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By iLead controller please refer to the user guide of iLead or by universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show IM8S IM7S on the display and move all the motors to their home position and you may hear some noises for about
11. ds If this happens clean the lamp with denatured Consistent DMX configuration enable iMove to be linked together with iRock and iShow and controlled at the same time e DMX address can be set remotely by iLead controller please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain alcohol and wipe it with a lint free cloth before installation AORA SHAT ming DEWEEN DINA NONNA MALEN SIANA AONE programs 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube 5 3 2 DMX Controller 7 rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life An universal DMX controller to control the units you have to set DMX address from 1 to 512 5 Make sure the lamp is located in the center of the reflector for the best spot Adiusi channel so that the units can receive DMX signal l amp position by screws A B and C ao Press the MENU button up to when the Gor is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP bution to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the fun
12. heck the connection of power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Make sure the unit does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head 5 5 DMX512 Connection The DMX512 is widely used
13. in intelligent lighting control with a maximum of 512 channels 1 2 0 N N N 7 PO ON CO GA Re ON ay 4 Of S E Ow S a LJ LI LW a LJ LI WL DMX512 INPUT 120 ohm 1 4W DMX OUTPUT Q 1 If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin adapter 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMxX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the DMX INPUT Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture input of the next unit The cable can not branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circ
14. pped OT 5 082 Orange Blue 120 Slowest speed O65 07S Orange ocumiercloakwisa OS 7 DT ied oe Or ieee 03 060 Yalow 044 057 Light Bluse yellow G35 045 Light Blue 031 037 Magana Lah Alive Dta020 Magenta D15 U22 areenaa C080 15 Sree CHU U Wens 010 Fasles ipaed tanieri kete OO0 005 Si ppi O00 raU Stand by Blackout the unit 3 Lamp Strobe X Y moving show Color Gobo selection X Y moving setting 1 Gobo Color sync mode selection 1 Hold on for gobo 1 Pan position strobe Show 1 Show 4 change 2 Tilt position Function 2 Sync strobe Please refer to Show 2 Press shortly for 3 Dimmer In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off 3 Two light strobe mode in 4 2 Main color change First set Master unit Function then set Slave units position Because of its high internal pressure there might be a risk that the Discharge lamp Sound 1 Sound 2 Slow Sound 3 Position Latch would explode during operation The lamp emits intense UV radiation which is harmful to LED off LED blinki LED LED fast blinki l a l eee on l ae the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp 5 3 1 iSolution Operation Discharge lamp HTI 150W 1 Always switch off the main supply and never handle the lamp or luminaries when is hot 2 Do not touch the bulb with bare han
15. rol on the first unit will control all the other units for Stand by Function and Mode Ii I 1 I Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to 1 ICO when the _Oor JSP i ICO button again return to the mode O37 the MENU button 1 doP lt 1 Wg wv g Focus Adjust Press the MENU button up to when the is blinking on the display Use the ENTER button to change to the mode display inversion It will automatically store after 8 seconds Or press the ENTER display normal To go back to the functions press Coos CTOOu Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling is blinking on the display Pressing ENTER button the unit will focus on tilt 90 and then the unit will focus on pan 0 pan 90 pan 180 pan 270 in every pressing ENTER button Use DOWN and UP button to adjust focus To go back to the functions press the MENU button again Self Test Press the MENU button up to when the LO L C Ln er is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Fixture Hours Press the MENU button up to when the
16. technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack or power pack Do not touch any wire during operation as high voltage might be causing electric shock Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or housing are damaged 6 The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 30 kgs for each unit 4 6 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 C
17. ug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened 2 2 Beam angel Lamp STE Maam angle fo dagrae ITTU TJA E E 197 iiiki oO 2 5 5 75 10 Distance m 5 4 DMX512 Configuration Chi L ch Oca o o I o O O Shutter Shaking n 248 244 Gpen 255 Pastest speed Gobo change 347 Fashest speed Shaking 1I Slowest apeed shaking AO 095 4 4 IE Speal epeed shila aa O84 016 031 00 015 Open 000 007 Blackout GODT 8 ad Gobo Rotation Di Split 288 255 Stopped 285 Fabeal opened Faine ge alec 128 Slowest pee Fain baw ate 1H127 Fink TE 112 Lightsreen O 102 Ui Pep le OTrT 08S Blus ON4 O078 Grange 63 063 Yalow 0S Light Blue Oe O Hageman 2 075 Green G00 32 Wihibe 735 Fasivel apaid Aombow afect 345 fastest speed Cochwise C o 128 Howes speed Rigenbicnma etfact 121 127 Penk 1129420 Lohit Green 1068 1172 Ul Purples light seen 228 105 LS Purje DS1 08Y BoueeUy Purple 155 Skypa piid Ghee keel ee 033 000 Bus 21 144 Sto
18. uit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 2 Technical Specification Power supply AC 120V 60Hz Lamp Discharge HTI 150W GY 9 5 Optical system Standard 13 focused beam angle Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 10 flashes per second Gobo wheel Independent gobo wheel with 7 gobos plus open gobos are interchangeable 4 metal gobos 2 glass gobos and 1 effect gobo Gobo wheel rotates with variable speed giving shaking effect Color wheel Independent color wheel with 9 dichroic mirrors plus white Color wheel rotates with variable speed giving rainbow effect Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX controller Color Chanmel8s oo Dimension 373mm x 295mm x 451mm Weight 13 kg 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unpl
Download Pdf Manuals
Related Search