IRDW-9021456-01D-13 User Manual INTRODUCTION
Contents
1. 0 12 not strobe 13 255 Strobe 255 is the fastest CH9 0 128 White balance close White balance open while in 129 255 5 CH1 200 255 Audio control open CH2 CH8 Not available CH9 is in 0 128 White balance closed White balance open while in 129 255 JII Multi Fixtures Connection DMX controller output Lamp 1 The input output connector s instruction PIN1 GND Earthed connector PIN2 COLD Data Negative S PINS HOT Data Positive S Technical Specification Input voltage AC96V 250 50Hz Power Consumption 240W LED 21pcs 10W 4 in 1 RGBW Weight 7 5Kg Size 391X312X426MM Maintenance 1 Trouble Shooting Lamp 2 Lamp N Problem Probable cause s Suggested remedy Fixtures do not work No power source Check if power source is on or cord works well False or incomplete data connection Check repair or change the data line Ensure connection is well and the first lamp s single input is connected with the controller output False address setting Check DMX address Reset normally but console Abnormally or no response Problem of signal connector of some fixtures Pull out the signal output and input of one fixture Then connect both directly If it works well this fixture is proved to be the failed one Handle the rest fixtures alike to check which fixture has problems If any problem please connect the technician 2 Cleaning and Maintai2. TEST Mode wenu H rest Hirr Hrs Hrs Hew Enter into TEST menu Select T R menu press ENTER to confirm then select red to test all red right and break off slowly Select T G menu press ENTER to confirm then select Green to test all Green bright and single color fade Select T B menu press ENTER to confirm then select Blue to test all the Blue right Page 6 of 9 and single color fade Select T W menu press ENTER to confirm then select White to test all the Blue right and single color fade 6 White balance setting Enter into BLNC menu set R G B W separately to make then mixing to be White color then press ENTER to save the setting If you want the White balance under the Auto and Sound mode the B EN must set in ON if the setting is OFF it means White Balance closed Under DMX mode the data of No 9 channel is 128Y or above it means BLNC open otherwise it means closed The original status is OFF 7 Temperature checking mode Enter into MODE menu select TEMP menu press SET to enter into Temperature checking mode then press EXIT to go out 4 Channel Function Introduction channel Data Description Name 1 Red LED 0 255 Red dim 2 Green LED 0 255 Green dim 3 Blue LED 0 255 Blue dim 4 White LED 0 255 White dim OBY 4 controller and DMX512 controller is acceptable 4 Channel Function Introduction 1 CH1 0 10 DMX internal program data fixture break off 2 CH1 11 10
3. 0 if CH2 is in 0 128 CH3 is the general dim for RGBW CH4 is the max Red fade CH5 is the max Green fade CH6 is the max blue fade CH7 is the Page 7 of 9 max White fade CH8 is single color fade 255 is the fastest speed fade If CH2 is in 129 255 CH3 is the general dim for RGBW CH4 is Red dim CH5 is Green dim CH6 is Blue dim CH7 is White dim CH8 is Strobe control 13 is a step in 0 12 is Strobe 255 is the fastest speed of strobe CH9 is in 0 128 white balance closed 129 255 means open white balance 3 CH1 101 105 White balance parameter save First set CH1 in 0 10 reset DMX parameter then set CH1 to 11 100 CH2 to 129 255 CH3 to 255 CH8 to 0 CH9 to 0 CH4 is red dim CH5 is Green dim CH6 is Blue dim CH7 is White dim adjust CH4 CH5 CH6 and CH7 to mix color to White Then push CH2 to 101 105 RGBW 4 color LED break off wait about 5 seconds Green LED bright the push CH1 to 0 the save the data of CH4 CH5 CH6 CH7 as RGBW 4 colors White Balance 4 CH1 106 200 Open 4 internal program If CH2 is in 51 100 4 colors uncross fade in program 1 If CH2 is in 51 100 15 colors uncross fade in program 2 If CH2 is in 101 150 4 colors cross fade in program 3 If CH2 is in 151 255 15 colors cross fade in program 4 CH3 adjust the keeping time for each scene 255 is the fastest CH4adjust the fading time for each scene 0 is not fade 1 255 is fade and 255 is the fastest CH5 CH6 CH7 not available CH8 adjust for Strobe
4. IRDW 9021456 01D 13 User Manual INTRODUCTION 1 INTRODUCTION WARMING INSTALLATION AND SETTING OPERATIONAL INSTRUCTION FUNCTIONS AND CHANNELS DISTRIBUTION Page 1 of 9 6 DAILY MAINTENANCE 7 TECHNOLOGY SPECIFICATION Thank you for your choosing Neo Neon LED PAR Light Product Series IRDW 9021456 01D 13 it can works under 4 kinds of working mode they are DMX Auto Audio and Stand Alone mode Also with Grade 225 mix color Fade and Strobe functions Main Points x DMX 512 controller with two modes 9 DMX Channels and 4 DMX Channels R G B With Standard color Strobe and Dimmer DMX Auto Audio Stand Alone functions RGBW mix color is grade 255 Provided dimmer fully 21pcs 4 in 1 RGBW 10W LED Please read this user manual fully before attempting to use the fixture Warming Please read this user manual before using and obey the operational instruction For indoor use the fixture must store at the dry and airiness place to avoid the short circuit by the humidity and rain Do not install it nearby hot place in case rising temperature of lamp damage itself Do not barrier vent in order to ventilation well and dissipation in time Connect the fixture with power source which has ground line and voltage of power source is in accordance with rating voltage lf fuse was damaged change the same type of fuse Not ready for any accessory you can only choose accessories the manufacturer prov
5. annels UP channel into then press setting Then UP DOWN to revise press the needed auto ENTER running program press ENTER to confirmed press MENU to exit 7 Auto AUPG Press 1 4 Press ENTER to enter program UP into then press setting Then UP DOWN to revise press the needed auto ENTER running program press ENTER to confirmed press MENU to exit 8 Speed of AUSP Press 1 4 Press ENTER to enter 1 4 color Auto UP into then press uncross program Then UP DOWN to revise fade setting press the needed auto 2 15 color ENTER running program uncross press ENTER to fade confirmed press 3 4 color MENU to exit cross fade 4 15 color cross fade 9 Auto AUSB Press 0 20 Press ENTER to enter O not program UP into then press strobe strobe Then UP DOWN to revise 1 20 setting press the needed auto strobe ENTER running program 20 fastest press ENTER tof strobe confirmed press MENU to exit 10 Auto AUFT Press 0 8 Press ENTER to enter 0 not fade program UP into then press 1 8 fade fake Then UP DOWN to revise 8 is the speed press the needed auto fastest setting ENTER running program fade Page 4 of 9 press ENTER to confirmed press MENU to exit 11 TIREE TEMP Press When the temperature UP of the fixture is over 90 Then degree the fixture will press turn off automatically ENTER the protect will not to ch
6. eck burn out the temperat ure of the fixture Il Function Introduction 1 Auto running mode A Press MODE setting to AUTO then press ENTER to confirm Then the fixture enter into the Auto mode B Set the AUPG into each No from 1 4 then press ENTER to confirm now you can select the program as below a 4 color uncross fade b 15 color uncross fade c 4 color cross fade d 15 color cross fade C Set the AUSP into each No from 1 8 press ENTER to confirm now you can select the speed of the program 1 is the slowest and 8 is the fastest The slowest is 4 seconds the fastest is10 mulliseconds D Set the AUSP to each No from 0 20 press ENTER to confirm now you can set Page 5 of 9 the speed of the Strobe 0 is not strobe 1 20 is Strobe 20 is the fastest Strobe E Set the AUFT to each No from 0 8 press ENTER to confirm setting the speed of the fade program 0 is not fade 1 to 8 is Fade 8 is the fastest fade mode 2 Audio running mode Enter into MODE menu select SOUND mode then press ENTER to confirm now you have enter into Audio Mode 15 color running 3 DMX running program Enter into MODE menu select D512 to DMX mode then go into SET menu to set DMX address ADDR 1 512 DMX channel number setting CH is 4 channel or 9 channel 4 DMX Stand alone Mode Enter into MODE menu select D512 menu press ENTER to confirm now you have enter into Stand Alone working mode 5
7. ides when need repairing Surrounding temperature of the lamp should not exceed 40 Page 2 of 9 If any problem send out professional technician to solve Menu Introduction MENU BE SUBMENU HOW TO ENTER No ITEM DISPLAY MODI N FUNCTION DISPLAY a j CHOOSE SUBMENU 1 MENU MENU Display once turned on 2 Working MODE Press Press UP or DOWN to Setting mode UP y AUTO select Press working Then SOUND ENTER to confirm mode of press press MENU to exit the fixture ENTER D512 3 Test TEST Press T R Press ENTER to enter Select the different UP TG into press tested color LED Then UP DOWNto select color press T B color Press ENTER ENTER for confirming press T W MENU to exit 4 Balance BLNC Press B R Press ENTER to enter The parameter UP then B G into then press balance setting press B B UP DOWN to parame of ENTER B W revise the needed R G B B EN auto running W program press B EN is ENTER to toswitch confirmed press on or off MENU to exit the balance 5 DMX AXXX Press 1 512 Press ENTER to enter address UP into then press setting Then UP DOWN to revise press the needed auto ENTER running program press ENTER to confirmed press Page 3 of 9 MENU to exit 6 DMX CH Press 4 9 Press ENTER to enter ch
8. ning Though increasing reliability by designing well and we never stop to improve quality to lengthen lamp s lifespan It is still indispensable to maintain it well by certain time in order to ensure best performance Check connecting line wiring and ground line to ensure safety of using lamp during a certain time Page 9 of 9
Download Pdf Manuals
Related Search