FX3UC-4AD INSTALLATION MANUAL
Contents
1. 2 Ground the twisted shield cable at one point on the PLC However do not use common grounding with heavy electrical systems e Make sure to properly wire to the European terminal board in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed 5 1 Wire and Terminal Tightening Torque 5 1 1 Cable 1 Applicable cable Type Wire size Single wire 0 3mm to 0 5mm 2 AWG22 to 20 Double wire 0 3mm AWG22 2 2 Termination Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Al 0 5 8WH e Bar terminal with insulating sleeve Pressure bonding tool CRIMPFOX ZA 3 or CRIMPFOX UD 6 Manufacturer Phoenix Contact e Stranded wire solid wire Insulating sleeve Contact area IN2. Power connector FX2NC 10BPCB1 Power crossover cable FX2NC 100BPCB Power cable FX3UC Series PLC Main unit Terminal block FX2NC 100BPCB Power cable DC h Class D grounding e Ground the ea terminal to the Class D grounding line 100 or less together with the ground terminal of the main unit e Remove the resin cover from the power crossover connector and perform crossover wiring to connect the power line from 4AD to a succeeding extension block 5 4 Wiring of Analog Input For the terminal layout refer to Chapter 3 If current input is selected 1 shield Terminal FXSUC AAD VO IO cho the channel number represents Use the 2 core shielded twisted pair cable for the analog input lines and separate the analog input lines from the other motive power lines or inductive lines 2 To use the current input be sure to short circuit the line between the VO terminal and the IL terminal L channel number 3 The SLD and a terminals are connected to each other inside 4 Do not connect any lines to the e terminal 6 Specifications STARTUP AND MAINTE NANCE PRECAUTIONS CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair
3. contact your local Mitsubishi Electric distributor e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a certified electronic waste disposal company for the environmentally safe recycling and disposal of your device TRANSPORT AND STOR AGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product 6 1 Applicable PLC FX3uUC Series PLC Ver 1 30 or later From the production manufactured in August 2004 with SER No 48 Applicable PLC 6 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the manual of the PLC main unit 6 3 Power Supply Specifications Item Specifications A D conversion circuit driving power 24V DC 10 80mA 24V DC power is supplied from the power connector 5V DC 100mA 5V DC power is supplied from the internal power supply of main unit it is not necessary to prepare power supply Interface driving power 6 4 Performance Specifications Specifications Item z Voltage input Current input Analog input 10 to 10V DC 20 to 20mA 4 to 20mA DC range Input resistance 200 kQ Input resistance 250 Q Offset 10 to 9V 20 to 17mA BE 10V or
4. less 30mA or less Gain Gain Offset gt 1V Gain Offset gt 3mA Maximum absolute input 30mA Effective numeric value 15bits Sign 1bit 0 32mV 20Vx1 64000 2 50mV 20Vx1 8000 Effective numeric value 14bits Sign 1bit 1 25mA 40mAx1 32000 5 00uA 40mAx1 8000 e 0 5 200nA for full scale of 40mA when ambient temperature is 25 C 5 C and a current of 20 mA to 20 mA is input Digital output Resolution 2 e 0 3 60mV for full scale of 20V when ambient Same when input is 4mA to temperature is 25 C 5 C 20mA 100mV for full e 1 0 400uA for full scale of 40mA when ambient temperature is 25 C 5 C and a current of 20 mA to 20 mA is input Same when input is 4mA to 20mA 500us x number of selected channels If channels use the digital filter s Sms x number of selected Total accuracy 0 5 scale of 20V when ambient temperature is 0 C to 55 C A D conversion ue channels e The photo coupler insulates the analog input area from the Insulati PLC rare e The DC DC converter insulates the analog input area from the power supply unit e Channels are not insulated from each other Occupied points 8 point Count either the input or output points of the PLC 1 Change the offset and gain values to change the input characteristics However the resolution doesn t change even when the offset and gain values change In the direct indication mode however the offset g
5. 6 1 Applicable PLC FX3uUC Series PLC Ver 1 30 or later From the production manufactured in August 2004 with SER No 48 Applicable PLC 6 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the manual of the PLC main unit 6 3 Power Supply Specifications Item Specifications A D conversion circuit driving power 24V DC 10 80mA 24V DC power is supplied from the power connector 5V DC 100mA 5V DC power is supplied from the internal power supply of main unit it is not necessary to prepare power supply Interface driving power 6 4 Performance Specifications Specifications Item z Voltage input Current input Analog input 10 to 10V DC 20 to 20mA 4 to 20mA DC range Input resistance 200 kQ Input resistance 250 Q Offset 10 to 9V 20 to 17mA 4 10V or less 30mA or less Gain Gain Offset gt 1V Gain Offset gt 3mA Maximum absolute input 30mA Effective numeric value 15bits Sign bit 0 32mV 20Vx1 64000 2 50mV 20Vx1 8000 Effective numeric value 14bits Sign 1bit 1 25mA 40mAx1 32000 5 00uA 40mAx1 8000 e 0 5 200nA for full scale of 40mA when ambient temperature is 25 C 5 C and a current of 20 mA to 20 mA is input Same when input is 4mA to 20mA 1 0 400pA for full scale of 40mA when ambient temperature is 25 C 5 C and a current of 20 mA to 20 mA is
6. 89989SSSSSS F LO For installation uninstallation Refer to the FX3UC Series User s Manual Hardware Edition 5 Wiring Power supply and analog input WIRING PRECAUTIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product WIRING PRECAUTIONS CAUTION e Make sure to observe the following precautions in order to prevent malfunctions under the influence of noise 1 Do not bundle the power line or twisted shielded cable together with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit high voltage lines or load line 2 Ground the twisted shield cable at one point on the PLC However do not use common grounding with heavy electrical systems e Make sure to properly wire to the European terminal board in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that
7. Crimp area When using a stick terminal with an insulating sleeve choose a wire with proper cable sheath referring to the above outside dimensions otherwise the wire cannot be inserted easily 5 1 2 Tightening Torque Tightening torque should be between 0 22 and 0 25 Nem Do not tighten terminal screws with a torque exceeding the regulation torque Failure to do so may cause equipment failures or malfunctions Termination of cable end 5 2 Tool To tighten terminals use a purchased With small sized screwdriver whose head is straight tip straight and is not widened as shown in the right figure 0 4mm 2 5mm Note If the diameter of screwdriver grip is too 0 02 T 0 1 small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25mm Manufacturer Phoenix Contact SZS 0 4X2 5 5 3 Power supply wiring Supply the 24V DC power to 4AD via the power supply connector Model Application Power crossover cable offered as an accessory for the FX2NC 10BPCB1 FX3UC 4AD Power cable offered as an accessory for the FX3UC FX2NC 100BPCB Series main unit 1 Connection example with the power supply through crossover wiring to the FX2NC input extension block FX3UC Series PLC Main unit FX3Uuc 4AD FX2NC Series PLC Terminal block Power crossover connector connector
8. For the purpose of this manual the FX3UC 4AD will from here be referred to as the 4AD 2 Incorporated Items Verify that the following product and items are included in the package Product FX2NC 10BPCB1 Power crossover cable Manual Special unit block No label l 1 HUET Y aL lite 0666608000 sii A 3 External Dimensions Part Names and Terminal Layout 15 0 6 74 2 92 15 gt S ooooo0oo0oonooo ojjpenonn0no0o0 00000 4 Mass Weight Approx 130g 0 29lbs 1 Status indicator LED PW Green Lit while 5 V power is normally supplied from PLC 24V Red Lit while 24V power is normally supplied from power supply A D Red Flashes during A D conversion 2 Terminal block European type Wiring of the voltage and current input 3 Connector PLC side Used to fix extension block on right side 4 DIN rail mounting hook 5 Slide lock Used to connect the FX3UC main unit extension block 6 Connector Extension side Used to connect extension block on right side of this special block Remove this cover for connecting 7 Power connector 24V DC The connector for supplying 24V power supply to 4AD 8 Power crossover connector Used to supply power supply to the extension block 4 Installation The 4AD can be installed on a DIN46277 rail 35 mm 1 38 wide INSTALLATION PRECAU TIONS WARNING e Make su
9. JY997D14901E MITSUBISHI ELECTRIC PROGRAMMABLE CONTROLLERS MELSEGIP JAPANESE ENGLISH FX3uc 4AD INSTALLATION MANUAL Manual Number JY997D14901 This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective April 2015 Specifications are subject to change without notice 2004 Mitsubishi Electric Corporation Reon E Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by CAUTION may also cause severe injury It is important to follow all precautions for personal safety As
10. Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN
11. ain cannot be adjusted 2 The resolution depend on the input mode 6 5 Input characteristics For the 4AD the nine kinds of input characteristics are provided for each input mode For the details of the input character refer to the following Input aad mode Inputmode nol istial output Reso Set value P g g 0 Voltage input mode 10 to 10V Boe 0 32mV 1 Voltage input mode 10 to 10V 4000 to 4000 2 50mV Voltage input mode 2 Analog value direct 10 to 10V tt 1 00mV indication 3 Current input mode 4 to 20mA 0 to 16000 1 25nA A Current input mode 4 to 20mA 0 to 4000 5 00nA Current input mode 5 Analog value direct 4to20mA 4000 to 20000 1 25nA indication 20 to 16000 to 20 to 4000 to 4000 5 00nA 6 Current input mode Current input mode N Current input mode 20 to 20000 to 8 Analog value direct 20mMA 20000 1 25nA indication 9toE Not used F No channels used This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary dama
12. cessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective April 2015 Specifications are subject to change without notice 2004 Mitsubishi Electric Corporation Reon E Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by CAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals Manual name FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition FX3S FX3G FX3GC FX3U FX3UC Series Programming Manual Basic amp Applied Instruction Edition Description Describes specifications for analog control and programming method for FX3S FX3G FX3GC FX3uU FX3UC Series PLC JY997D16701 MODEL CODE 09R619 JY997D16601 MODEL CODE 09R517 Describes PLC programming for basic applied instructions and devices Explains the FX3UC Series PLC specifications for I O wiring installation and ma
13. from October 1st 2007 FX3UC 4AD Standard EN61131 2 2007 Programmable controllers Equipment requirements and tests Remark Compliance with all relevant aspects of the standard EMI e Radiated Emissions e Mains Terminal Voltage Emissions EMS RF immunity e Fast Transients e ESD e Surge e Conducted e Power magnetic fields Caution for EC Directive The FX3UC 4AD have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered care fully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requirements Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are fol lowed for the users complete control system users should expect accuracy as specified in this manual e Sensitive analog cable should not be laid in the same trunking or cable conduit as high voltage cabling Where possible users should run analog cables separately e Good cable s
14. ge accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN JY997D14901E MITSUBISHI ELECTRIC PROGRAMMABLE CONTROLLERS MELSEGIP JAPANESE ENGLISH FX3uc 4AD INSTALLATION MANUAL Manual Number JY997D14901 This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever ne
15. hielding should be used Ground the shield of the twisted shielded cable at one point on the PLC side e When reading analog values EMC accuracy can be improved out by averaging the readings This can be achieved either through functions on the special function block for analog input or through a users program in the FX3UC Series PLC main unit e Please use FX3UC 4AD while installed in a shielded enclosure For the details refer to the following manual Refer to the FX3UC Series User s Manual Hardware Edition Note for compliance with EN61131 2 2007 General note on the use of the power supply cable The FX3uc 4AD unit requires that the cable used for power supply is 30m or less 1 Outline The FX3UC 4AD special function block for analog input converts four analog input values voltage current to digital values and transfers those digital values to the PLC main unit For the purpose of this manual the FX3UC 4AD will from here be referred to as the 4AD 2 Incorporated Items Verify that the following product and items are included in the package Product Manual Special unit block FX2NC 10BPCB1 No label Power crossover cable s RE mar l HY This A manual wel A 3 External Dimensions Part Names and Terminal Layout 15 0 6 74 2 92 15 gt S ooooo0oo0oonooo ojjpenonn0no0o0 00000 4 Mass Weight Approx 130g 0 29lbs 1 Sta
16. ide lock of the main unit extension block 4 The 4AD connector PLC side is connected to the main unit extension block connector whose cover was previously removed see the following figure 5 Slide back the slide lock of the main unit extension block to attach the 4AD Main unit 4 2 Installation In Enclosure 1 Push out all DIN rail mounting hooks 2 Fit the upper edge of the DIN rail mounting groove onto the DIN rail DIN46277 rail 35 mm 1 38 wide 3 Lock the DIN rail mounting hooks while pressing the PLC against the DIN rail 89898SSSSSS F For installation uninstallation Refer to the FX3UC Series User s Manual Hardware Edition 5 Wiring Power supply and analog input WIRING PRECAUTIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product WIRING PRECAUTIONS CAUTION e Make sure to observe the following precautions in order to prevent malfunctions under the influence of noise 1 Do not bundle the power line or twisted shielded cable together with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit high voltage lines or load line
17. input Same when input is 4mA to 20mA Digital output Resolution 2 e 0 3 60mV for full scale of 20V when ambient temperature is 25 C 5 C Total accuracy 100mV for full e 0 5 scale of 20V when ambient temperature is 0 C to 55 C 500us x number of selected channels A CONVErSION If channels use the digital filter s 5ms x number of selected time channels e The photo coupler insulates the analog input area from the redial PLC aria e The DC DC converter insulates the analog input area from the power supply unit e Channels are not insulated from each other Occupied points 8 point Count either the input or output points of the PLC Change the offset and gain values to change the input characteristics However the resolution doesn t change even when the offset and gain values change In the direct indication mode however the offset gain cannot be adjusted 2 The resolution depend on the input mode 6 5 Input characteristics For the 4AD the nine kinds of input characteristics are provided for each input mode For the details of the input character refer to the following Input es ae Input mode Analog Digital output Resolu input range range tion Set value 0 Voltage input mode 10 to 10V are 0 32mV 1 Voltage input mode 10 to 10V 4000 to 4000 2 50mV Voltage input mode 2 Analog value direct 10 to 10V e 1 00mV aes 10000 indication 3 Current inp
18. input is selected gt Terminal EXSUCAAD block 1 shield VOl I ch the channel number represents Use the 2 core shielded twisted pair cable for the analog input lines and separate the analog input lines from the other motive power lines or inductive lines 2 To use the current input be sure to short circuit the line between the VOI terminal and the IL terminal L channel number 3 The SLD and terminals are connected to each other inside 4 Do not connect any lines to the e terminal 6 Specifications STARTUP AND MAINTE NANCE PRECAUTIONS CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair contact your local Mitsubishi Electric distributor e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a certified electronic waste disposal environmentally safe recycling and disposal of your device company for the TRANSPORT AND STOR AGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product
19. intenance JY997D28701 MODEL CODE 09R519 FX3UC Series User s Manual Hardware Edition How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Certification of UL cUL standards The following product has UL and cUL certification UL cUL File Number E95239 Models MELSEC FX3UC series manufactured FX3UC 4AD Compliance with EC directive CE Marking This note does not guarantee that an entire mechanical module produced in accordance with the contents of this note will comply with the following standards Compliance to EMC directive and LVD directive for the entire mechanical module should be checked by the user manufacturer For more details please contact the local Mitsubishi Electric sales site Requirement for Compliance with EMC directive The following products have shown compliance through direct testing of the identified standards below and design analysis through the creation of a technical construction file to the European Directive for Electromagnetic Compatibility 2004 108 EC when used as directed by the appropriate documentation Attention e This product is designed for use in industrial applications Note e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Type Programmable Controller Open Type Equipment Models MELSEC FX3UC series manufactured
20. nts Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are fol lowed for the users complete control system users should expect accuracy as specified in this manual e Sensitive analog cable should not be laid in the same trunking or cable conduit as high voltage cabling Where possible users should run analog cables separately e Good cable shielding should be used Ground the shield of the twisted shielded cable at one point on the PLC side e When reading analog values EMC accuracy can be improved out by averaging the readings This can be achieved either through functions on the special function block for analog input or through a users program in the FX3UC Series PLC main unit e Please use FX3UC 4AD while installed in a shielded enclosure For the details refer to the following manual Refer to the FX3UC Series User s Manual Hardware Edition Note for compliance with EN61131 2 2007 General note on the use of the power supply cable The FX3Uc 4AD unit requires that the cable used for power supply is 30m or less 1 Outline The FX3UC 4AD special function block for analog input converts four analog input values voltage current to digital values and transfers those digital values to the PLC main unit
21. r impacts or expose it to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions Connect FX3UC 4AD securely to their designated connectors Loose connections may cause malfunctions Up to 8 units can be connected to the FX3uc Series PLC 1 Up to 7 units can be connected to the FX3UC 32MT LT 2 PLC 4 1 Connection to the PLC 1 Turn off the power Disconnect all the cables connected to the PLC and demount the PLC from the DIN rail 2 Remove the extension block connector cover on the main unit extension block 3 Slide the special block slide lock of the main unit extension block 4 The 4AD connector PLC side is connected to the main unit extension block connector whose cover was previously removed see the following figure 5 Slide back the slide lock of the main unit extension block to attach the 4AD Main unit 4 2 Installation In Enclosure 1 Push out all DIN rail mounting hooks 89999SSSSH9 9SHSSSHSSSD i 2 Fit the upper edge of the DIN rail mounting groove onto the DIN rail DIN46277 rail 35 mm 1 38 wide 3 Lock the DIN rail mounting hooks while pressing the PLC against the DIN rail
22. re to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAU TIONS CAUTION e Use screwdrivers carefully when performing installation work thus avoiding accident or product damage e Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or expose it to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions Connect FX3UC 4AD securely to their designated connectors Loose connections may cause malfunctions Up to 8 units can be connected to the FX3uc Series PLC 1 Up to 7 units can be connected to the FX3UC 32MT LT 2 PLC 4 1 Connection to the PLC 1 Turn off the power Disconnect all the cables connected to the PLC and demount the PLC from the DIN rail 2 Remove the extension block connector cover on the main unit extension block 3 Slide the special block sl
23. sociated Manuals Manual name FX3S FX3G F X3GC FX3U FX3UC Series User s Manual Analog Control Edition FX3S FX3G FX3GC FX3U FX3UC Series Programming Manual Basic amp Applied Instruction Edition Description Describes specifications for analog control and programming method for FX3S F X3G FX3GC FX3uU FX3UC Series PLC JY997D16701 MODEL CODE 09R619 JY997D16601 MODEL CODE 09R517 Describes PLC programming for basic applied instructions and devices Explains the FX3UC Series PLC specifications for I O wiring installation and maintenance FX3UC Series User s Manual Hardware Edition JY997D28701 MODEL CODE 09R519 How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Certification of UL cUL standards The following product has UL and cUL certification UL cUL File Number E95239 Models MELSEC FX3UC series manufactured FX3UC 4AD Compliance with EC directive CE Marking This note does not guarantee that an entire mechanical module produced in accordance with the contents of this note will comply with the following standards Compliance to EMC directive and LVD directive for the entire mechanical module should be checked by the user manufacturer For more details please contact the local Mitsubishi Electric sales site Requirement for Compliance with EMC directive The following products have sho
24. there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed 5 1 Wire and Terminal Tightening Torque 5 1 1 Cable 1 Applicable cable Type Wire size Single wire 0 3mm to 0 5mm 2 AWG22 to 20 Double wire 0 3mm AWG22 2 2 Termination Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Al 0 5 8WH e Bar terminal with insulating sleeve Manufacturer Pressure bonding tool CRIMPFOX ZA 3 Phoenix Contact or CRIMPFOX UD 6 e Stranded wire solid wire Termination of cable end Insulating sleeve Contact area IN Crimp area When using a stick terminal with an insulating sleeve choose a wire with proper cable sheath referring to the above outside dimensions otherwise the wire cannot be inserted easily 5 1 2 Tightening Torque Tightening torque should be between 0 22 and 0 25 Nem Do not tighten terminal screws with a torque exceeding the regulation torque Failure to do so may cause equipment failures or malfunctions 5 2 Tool To tighten terminals use a purchased With small sized screwdriver whose head is straight tip straight and is not
25. tus indicator LED PW Green Lit while 5 V power is normally supplied from PLC 24V Red Lit while 24V power is normally supplied from power supply A D Red Flashes during A D conversion 2 Terminal block European type Wiring of the voltage and current input 3 Connector PLC side Used to fix extension block on right side 4 DIN rail mounting hook 5 Slide lock Used to connect the FX3UC main unit extension block 6 Connector Extension side Used to connect extension block on right side of this special block Remove this cover for connecting 7 Power connector 24V DC The connector for supplying 24V power supply to 4AD 8 Power crossover connector Used to supply power supply to the extension block 4 Installation The 4AD can be installed on a DIN46277 rail 35 mm 1 38 wide INSTALLATION PRECAU TIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAU TIONS CAUTION e Use screwdrivers carefully when performing installation work thus avoiding accident or product damage e Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration o
26. ut mode 4 to 20mA 0 to 16000 1 25nA T Current input mode 4 to 20mA 0 to 4000 5 004 A Current input mode 5 Analog value direct 4to20mA 4000 to 20000 1 25nA indication 20 to 16000 to 6 Current input mode N 20 to Current input mode 20MA 4000 to 4000 5 00nA Current input mode 20 to 20000 to 8 Analog value direct 20MA 20000 1 25nA indication 9 to E Not used F No channels used This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with
27. widened as shown in the right figure 0 4mm 2 5mm Note If the diameter of screwdriver grip is too Kee kL small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25mm Manufacturer Phoenix Contact SZS 0 4X2 5 5 3 Power supply wiring Supply the 24V DC power to 4AD via the power supply connector Model Application Power crossover cable offered as an accessory for the FX2NC 10BPCB1 FX3UC 4AD Power cable offered as an accessory for the FX3UC FX2NcC 100BPCB f i Series main unit 1 Connection example with the power supply through crossover wiring to the FX2NC input extension block FX3UC Series PLC Main unit FX3UC 4AD FX2NC Series PLC Terminal block Power crossover connector connector Power connector FX2Nc 10BPCB1 Power crossover cable FX2NcC 100BPCB Power cable FX3UC Series PLC Main unit Terminal block FX2NC 100BPCB Power cable De h Class D grounding e Ground the re terminal to the Class D grounding line 100 Q or less together with the ground terminal of the main unit e Remove the resin cover from the power crossover connector and perform crossover wiring to connect the power line from 4AD to a succeeding extension block 5 4 Wiring of Analog Input For the terminal layout refer to Chapter 3 If current
28. wn compliance through direct testing of the identified standards below and design analysis through the creation of a technical construction file to the European Directive for Electromagnetic Compatibility 2004 108 EC when used as directed by the appropriate documentation Attention e This product is designed for use in industrial applications Note e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Type Programmable Controller Open Type Equipment Models MELSEC FX3UC series manufactured from October 1st 2007 FX3UC 4AD Standard EN61131 2 2007 Programmable controllers Equipment requirements and tests Remark Compliance with all relevant aspects of the standard EMI e Radiated Emissions e Mains Terminal Voltage Emissions EMS RF immunity e Fast Transients e ESD e Surge e Conducted e Power magnetic fields Caution for EC Directive The FX3UC 4AD have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered care fully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requireme
Download Pdf Manuals
Related Search