Home

Electra LED DMX Manual

1. the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Male Socket XLR Female Socket 1 e Figure 3 XLR Pin Configuration I I 2 Cold 1 Ground i Pin 1 Ground Pin 2 Data Compliment negative i l I l Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 0 and interference It is always advisable G X to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 American DJ Supply www americandj com Electra LED DMX User Manual Page 6 Electra LED DMX Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cabl
2. ELECTHA LED OMX 3 08 User Instructions American DJ 6122 S Eastern Ave Los Angeles CA 90040 www americandj com Electra LED DMX Introduction Introduction Congratulations and thank you for purchasing the Elec tra LED DMX by American DJe one of the finest pieces of its kind on the market today The Electra LED DMX is a great inexpensive light weight intelligent fixture Due to its physical specifications its a great piece for mobile DJ s roller rinks small clubs bars and bowling centers When used in multiples of two or more these units create an effect that rivals that of units that can cost up to three times the price The Electra LED DMX was designed to run in a Master Slave mode but can be used with any universal DMX 512 controller Customer Support American DJe provides a toll free customer sup port line to provide set up and installation help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www americandj com for any comments or suggestions Toll free customer service hours are Monday through Friday 9 00 a m to 5 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are n
3. LED DMX Fuse Replacement First unplug the power The fuse holder is located above the power cord Using a flat head screw driver unscrew the fuse holder Remove the bad fuse and replace with a new one American DJ Supply www americandj com Electra LED DMX User Manual Page 9 Electra LED DMX DMX Values and Traits Ch1 Value Pattern Chase Strobe Speed 255 Fast 250 255 Chase10 240 249 ChaseO9 D 230 239 Chase08 220 229 Chase07 210 219 Chase06 200 209 Chase05 P 190 199 Chase04 180 189 Chase03 500 SI 170 179 Chase02 AANA wai 160 169 Chase01 199 Fast 150 159 Pattern15 ah 140 149 Pattern14 eri 130 139 Pattern13 AAA 120 129 Pattern12 110 019 Pattern11 100 109 Pattern10 090 099 PatternO9 080 089 PatternO8 AA 070 079 Pattern07 060 069 PatternO6 050 059 PatternO5 040 049 Pattern04 A 030 039 PatternO3 020 029 PatternO2 010 019 PatternO1 000 009 Blackout 000 009 No Strobe 255 Fast MMMM 170 Slow 169 Fast 140 Slow 139 136 010 Slow Electra LED DMX a Blackout the unit 1 Sync Strobe 1 Sync Strobe Function 2 Asynchronism Strobe 2 Asynchronism Strobe 4 Move 3 Sound Strobe 3 Sound Strobe chase UC3 Control Auto LEDSlow Strobe Sound pan fast LED OFF Sound pan slow Mode LED ON American DJ Supply www americandj com Electra LED DMX User Manual Page 10 Electra LED DMX This chart list the DMX dip switch setting for DMX address 1 th
4. White None Any Safe Position Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice American DJ Supply www americandj com Electra LED DMX User Manual Page 15 American DJ Supply American DJ World Headquarters 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 582 2610 Web www americandj com E mail info americandj com American DJ Europe Junostraat 2 6468 EW Kerkrade Netherlands service americandjeurope com www americandjeurope com Tel 31 45 546 85 00 Fax 31 45 546 85 99
5. able for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e All American Audio Products 1 year 865 day Limited Warranty except V Plus Series Ampli fiers e All American Audio V Plus Series Amplifiers 3 year 1095 day Limited Warranty e American DJ Lighting and American DJ Branded Products 1 year 365 day Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding Laser Products and lamps e American DJ Laser Products 90 Day Limited Warranty e American DJ L E D Products 3 year 1095 day Limited Warranty excluding motors which have a 1 year 365 day Limited Warranty American DJ Supply www americandj com Electra LED DMX User Manual Page 13 Electra LED DMX Notes American DJ Supply www americandj com Electra LED DMX User Manual Page 14 Electra LED DMX Specifications Electra LED DMX 120v 60 Hz 230v 50Hz 52 LEDS 16 Red 12 Green 12 Blue amp 12 White 14W 15 Degrees 1 Amp 250mAmp 5 Lbs 2 6 Kgs 17 L x 8 W x 9 H RGB
6. blackout DMX Mode Operating through a DMX controller give the user the freedom to cre ate their own programs tailored to their own individual needs Follow the the set up directions that come with your DMX controller 1 This function will allow you to control each individual fixture s traits with a standard Elatione DMX 512 controller 2 The Electra LED DMX uses three DMX channels to operate Channel 1 is Pan channel 2 is Pattterns amp Chases and channel 3 is Strobe 3 Torun your fixture in DMX mode plug in the fixture via the XLR connections to any standard DMX controller Set your desired DMX address using the dipswitches on the bottom of the fixture To set your address you can use the address chart on page 11 4 Plug in the fixture via the XLR connections to any standard DMX controller Master Slave Operation This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the con American DJ Supply www americandj com Electra LED DMX User Manual Page 8 Electra LED DMX Operating Instructions trolling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Daisy chain your units via the XLR connector on the rear of the unit Use approved DMX 512 data cables to link your units to gether Remember that the Male XLR connector is the input and the Female XLR connector is the out
7. ch fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is as signed a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The X Move LED can be controlled via DMX 512 pro tocol The Electra LED DMX is be a three chan nel DMX unit The DMX address is set using the dipswitches on the bottolm of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure Si to use standard 110 120 Ohm shielded cable This Figure 1 cable may be purchased at almost all professional sound and lighting American DJ Supply www americandj com Electra LED DMX User Manual Page 5 Electra LED DMX Set Up stores Your cables should be made with a male and female XLR con nector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use
8. d or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 12 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed
9. es for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 American DJ Supply www americandj com Electra LED DMX User Manual Page 7 Electra LED DMX Operating Modes The Electra LED DMX can run as a stand alone fixture or in a master Slave configuration It has two operating modes e Sound Active mode The unit will react to sound chasing through the several built in programs You can also use the optional UC3 Remote Control to blackout the fixture or control different functions e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the American DJ Show Designer Operating Instructions For best results use fog or special effects smoke to enhance the beams projections Sound Active Mode 1 To operate the fixture in sound active mode put dipswitch 1 in the On position 2 The Electra LED DMX will now react to the bass sound of music via the internal microphone 4 The optional UC3 Controller not included may be used to con trol different functions including
10. ity to establish the date and place of purchase by ac ceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product Contact American Du Inc Service Department at 800 322 6337 Send the product only to the American Du Inc factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty American DJ Inc will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product American Du Inc shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which American DJ Inc concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the American Du Inc factory unless prior written authorization was issued to purchaser by American Du Inc if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or peri
11. o user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact American DJe customer support Please recycle the shipping carton when ever possible Improvements and changes in specifications and design to this manual and unit may be made at any time without prior notice American DJ Supply www americandj com Electra LED DMX User Manual Page 2 Electra LED DMX General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Electra LED DMX Includes Built In Hanging Yoke Sound Active Light Weight LED Output Similar to 250W Lamp Voltage is User Selectable UC3 Controller Not Included 2 Operating Modes Sound Active and DMX 512 Control Electra LED DMX Warranty Registration The Electra LED DMX carries a three year 1095 days limited war ranty Please fill out the enclosed warranty card to validate your pur chase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A num ber The R A number must be clearly written on the
12. odic check up During the period specified above American Du Inc will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Ameri can DJ Inc under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of American DJ All products covered by this warranty were manufactured after January 1 1990 and bear identifying marks to that effect E American DJ Inc reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore man ufactured No warranty whether expressed or implied is given or made with respect to any acces sory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by American Du Inc in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall American Du Inc be li
13. outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must pro vide a copy of your proof of purchase invoice You may obtain a R A number by contacting customer support at 800 322 6337 Electra LED DMX Features Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact American DJe During operation the housing may become extremely hot Avoid touch ing the unit with bare hands while in use American DJe will not accept any liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to this unit American DJ Supply www americandj com Electra LED DMX User Manual Page 3 Electra LED DMX For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit e To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been fraye
14. put The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 The first unit in the chain master will use the female XLR connec tor only The last unit in the chain will use the male XLR connec tor only 3 Turn dipswitch 1 to the On position on the master unit 4 For the slave units any dipswitch can be set to the On position except dipswitch 1 5 When running fixtures in Master Slave configuration you can make the mirror pan of the 1st and 2nd fixtures contrast the mirror pan of the 3rd and 4th fixtures Example Four fixtures are linked together On fixtures 1 and 3 set the fixture 1 as a master and set fixture 3 as a slave For fixtures 2 amp 4 set them as slaves as well but also put dipswitch 10 in the On position The mirror pan of fixtures 1 amp 2 will run the same and the mirror pan of fixtures 2 amp 4 will run in contrast to fixtures 1 amp 2 This makes a great light show 6 You can also use the optional UC3 Remote Control If you want to use the optional remote control connect the UC3 controller to the first fixture in the line master Note The remote control only operates in Stand Alone and Master Slave modes If the remote is connected in DMX mode it will not func tion If the units do not receive an active DMX signal the units will automatically react to sound in the Master Slave mode Electra
15. rough 511 Follow the instructions below to configure fixture dip switches with your desired DMX address DMX Address Quick Reference Chart DMX Dipswitch Chart DIP a Dip Switch Position Ef Ea EE D x on O x on x on Ea O O xe Polo fol xe DAOA po x o oo of xO 19 51 838 115 147 179 211 243 275 307 339 371 403 435 467 499 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511 DMX Address oO O Dip Switch Position DMX Address The center numbers of this chart 1 511 represent a DMX address The X s and O s along the top and side of the chart represent dip switch poistion X for off and O for on Find your desired DMX address from the center chart Identify the position for dip switches 1 5 from the chart on the left and dip switches 6 9 from the chart on the top Adjust the dip switches on your fixture to match the position settings of the chart For fixtures with 10 dip switches dip switch 10 is reserved for special functions American DJ Supply www americandj com Electra LED DMX User Manual Page 11 Electra LED DMX Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20 days Sit
16. to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance Safety Precautions American DJ Supply www americandj com Electra LED DMX User Manual Page 4 Electra LED DMX Set Up Power Supply Before plugging your unit in be sure the source voltage in your area matches the required voltage for your American DJe X Move LED The American DJe Electra LED DMX has a user selectable voltage switch Because line voltage may vary from venue to venue you should be sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant Jo ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in whi
17. uation may very If used heavily in clubs with lots of fog cleaning may be required more often 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Trouble Shooting Electra LED Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure the voltage of your fixture matches the voltage of the wall outlet 2 Be sure the fuse has not blown The fuse is located on the rear panel Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit American DJ Supply www americandj com Electra LED DMX User Manual Page 12 Electra LED DMX Warranty MANUFACTURER S LIMITED WARRANTY A American Du Inc hereby warrants to the original purchaser American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibil

Electra LED DMX Manual

Contents

Download Pdf Manuals

Related Search

Related Contents