Home

USER MANUAL - Pager2.net

1. 4 Press UP or DN scroll button to set on off time and press Read Select to move through the segments Set Key Tone On Off 1 Using the UP or DN scroll button scroll until display shows Set Key Tone 2 Press Read Select to set key tone on off 3 Use the UP or DN scroll button to select On or Off 4 Press Read Select to set Select Alert Mode 1 Using the UP or DN scroll button scroll until display shows Set Alert Mode 2 Use the UP or DN scroll button to select Beep Vibe or Both 3 Press Read Select to set Beep Use the Up or DN scroll button to select Select Beep Type Loud or Soft and press Read Select to set Set Alert Time seconds and press Read Select to set Vibe Use the Up or DN scroll button to select Set Vibe strength Strong or Weak and press Read Select to set Set Vibe Pulse Cnst P1 P2 or P3 and press Read Select to set Set Alert Time seconds and press Read Select to set Both Use the Up or DN scroll button to select Set Vibe strength Strong or Weak and press Read Select to set Set Alert Time seconds and press Read Select to set Battery The RX E 4 Line Alphanumeric pager uses 1 AAA Battery Programming To program the pager see pg 29 Long Range Systems 36 Freedom User Manual Using the Star Pager ida 1 Jy 8004974996 Charging Any rechargeable pager will require use of an LRS charger
2. Follow instructions on display Turn the pager off then on _ When it stops vibrating press ENTER Note more than 1 pager can be encrypted at once Long Range Systems 30 Freedom User Manual The unit will wait 5 seconds and send out the signal The screen will display prg encryption none or 128 bit key then Transmitting Key Continue this procedure with the remaining pagers Program Pager Vibration The Program Vibration feature can program a set of Guest or Staff Pagers all at once to Vibrate or not Vibrate when paged 1 Press Setup and enter Password Press F2 DN Press 1 to select 1 Program f j A OO OMONOOOE WH Be sure All Pagers are on the Charger Press 2 to select 2 Prg Vibe Press 1 to select Guest Pagers or 2 to select Staff Pagers If selected Guest select 1 for Coaster Pagers or 2 for Paddle Pagers Press F1 YES to enable Pager to Vibrate or F4 NO to prevent the Pager from Vibrating Unplug the charger power supply When Pagers finish flashing press ENTER Pagers will slowly brighten and dim to off to indicate they are being Programmed Note Pagers will vibrate during glowing if vibration is enabled and will not vibrate if vibration 12 was disabled When finished plug the charger power supply back in Program Welcome Message The Welcome Message on a Staff 4 Line Alpha pager can be customized to show something new when the
3. Nursery Teller Officer Buffet Diaper change Child crying To nursery Freedom User Manual Special Functions User Password All of the functions that adjust paging preferences are protected by a Password To reduce tampering with critical settings the keypad is password protected The Password 56789 allows you to enter most restricted programming screens Press F4 at any menu to return to the Guest menu Theft Deterrent Function Theft deterrent is used to alert staff and guests that they are leaving the premises while still carrying the coaster pager When Activated The transmitter sends a signal to the coaster pager and if the signal is not received the coaster pager will emit a continuous beep sound until it is returned to the charging unit or back in range The LED screen on the alphanumeric pagers will display OUT OF RANGE When theft deterrent mode is active a T will display on the upper left corner of the transmit ter display OUT OF RANGE AREA PAGERS ALARM IN RANGE AREA PAGERS OPERATE NORMALLY To Activate 1 Press SETUP and enter Password 2 Press 1 SYSTEM 3 Press 1 Anti Theft 4 Press F1 YES to turn theft mode on Press F2 NO to turn off 5 Main screen display will show T on upper left corner when turned on Long Range Systems 9 Freedom User Manual Tracking This function allows the host to monitor which Guest or Staff pager has been paged and continues
4. Press SETUP and enter Password Press 3 Other Press F2 Down Press 3 Network Press 1 Enabled Press F1 Yes to enable or press F4 No to disable Network OOo PR 0nN o N q go 10 0 P OQ NM For Users on DHCP Network From Network Menu 1 Press 2 DHCP 2 At prompt Use DHCP press F1 Yes For Users on Static Network For users on a Static Network the user will need a valid IP Address available on their internal network Contact your local Network Administrator for an available IP address Note f an P Address has one or two digits the address must be written out fully example 192 168 7 17 must be entered 192 168 007 017 From Network Menu 1 Press 2 DHCP 2 At prompt USE DHCP press F4 No 3 Press 3 IP Long Range Systems 25 Freedom User Manual Enter IP Address to assign for the Freedom Transmitter on Network and press ENTER Press F2 Down Press 1 Netmask Enter Netmask address for the Freedom TransmitterT7460 on Network and press ENTER Press 2 DNS Enter DNS address for the Freedom Transmitter on Network and press ENTER Press 3 Gateway O O ON OO 2 Enter Gateway address for the Freedom Transmitter on Network and press ENTER To select if a Guest receives an SMS text message or a Voice recording 1 Press SETUP and enter Password 2 Press 1 System 3 Press 2 Cell Phone Paging 4 Press 2 Type 5 Press 1 for SMS Text or 2 for Voice Messa
5. Pager is powered on 1 2 3 4 Press SETUP and enter Password Press F2 DN Press 1 to select 1 Program Press 3 to select 3 Prg Welcome 5 Type in New Welcome Message and press ENTER Note 7he welcome message has a 32 character limit 6 Turn off and then turn on Alpha Pager 7 8 Press ENTER Pager should Beep Once to indicate programming 9 Cycle power on Pager to view New Message Long Range Systems 31 Freedom User Manual System Specifications Notice Operation is subject to the following This device may cause interference This device will accept any interference including interference that may cause undesired oper ation of the unit Notice To reduce potential radio interference to other users the antenna type and gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than required for successful communication Transmitter Required voltage One 110 220V outlet for the pager keypad Operating Frequency 420 470MHz Radiated Power lt 4900 micro volts meter Operating Range Dependent upon pagers used topography and environment Battery Powered Pagers Required voltage One AAA Alkaline battery for the pager Rechargeable Pagers Required Voltage 1 110 220V outlets for pager charging base Battery Type Nickel Metal Hydride NiMH Rechargeable Lifetime of Batteries Approximately 3 5 years depending on usage Battery Charge Life App
6. Transmitter T7460 Set Date 1 Press SETUP and enter Password 2 Press 3 Date Time 3 Press 3 Set Date 4 Enter Date MM DD YY e g March 11 2010 03 11 10 and press ENTER Set Time Press SETUP and enter Password Press 3 Date Time Press F2 DN Press 1 Set Time Enter Time e g 08 30 and select F1 AM or F2 PM a FF WN gt Time Format 1 Press SETUP and enter Password 2 Press 3 Date Time 3 Press 2 Time Format 4 Select 1 12 hour or 2 24 hour Note Asterisk next to an option indicates the current operation mode Date Format 1 Press SETUP and enter Password 2 Press 3 Date Time 3 Select 1 Date Format 4 4 Select 1 MM DD YY or 2 DD MM YY Note Asterisk next to an option indicates the current operation mode 24 HOUR TIME 12 HOUR TIME ON DISPLAY ON DISPLAY 13 34 56 1 34 56 PM GUEST T7460 Transmitter Screen Long Range Systems 17 Freedom User Manual Repeat Delay When using a repeater it may be necessary to add a delay between pages when paging multiple pagers to allow the repeater time to repeat the signal and detect the next one To add repeat delay 1 Press SETUP 2 Enter Password 3 Press 1 System 4 Press F2 DN until the display shows 2 Repeat Delay 5 Press 2 2 Repeat Delay 6 Select F1 Yes to enable or F4 No to disable ID Span In very large systems up to 9999 Guest pagers can be paged To do
7. its officers employees sub sidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unau thorized use even if such claim alleges that LRS Inc was negligent regarding the design or manufacture of the part de vice or system EU DECLARATION OF CONFORMITY We Long Range Systems hereby declare under our sole responsibility that the Freedom paging transmitters and on site pagers comply with the essential requirements in the European RE amp TTE Directive 1999 5 EC of the European Parliament of the Council of 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recog nition of their conformity The following standards were utilized ETS 300 224 1998 EN 301 489 2 2002 EN61000 3 2 1998 EN 61000 3 3 1995 EN 60950 1992 with 41 42 amp A3 XU 0063 030811 Long Range Systems 42 Freedom User Manual
8. use Rechargeable pagers that are left off of charge for longer than 30 days will have a negative impact on the life of the batteries requiring them to be replaced thus voiding the warranty If this product should become defective within the warranty period we will repair or replace it with an equivalent product free of charge LRS will return your product via UPS ground shipping All warranty claims must be initiated through our customer service department Customer Service 800 437 4996 4550 Excel Parkway Suite 200 Addison TX 75001 This warranty gives you specific legal rights and you may also have rights that vary from state to state Copyright June 2010 Long Range Systems Inc All Rights Reserved This manual contains proprietary information of Long Range Systems Inc LRS and is intended for use only by its em ployees or customers None of the material contained herein may be copied reproduced republished downloaded dis played posted or transmitted in any form or by any means including but not limited to electronic mechanical photocopying recording or otherwise without the prior written permission of LRS Additional copies of this manual may be obtained by contacting LRS Screen displays keyboard layouts hardware descriptions or software are proprietary to LRS and are subject to copy right and other intellectual property rights of LRS and shall be treated in accordance with the previous paragraph All attempts have
9. 1 Place the pager in the charger 2 Allow unit to fully charge overnight 3 Remove from charger and pager will vibrate and light all lights as a verification that it is working 4 Replace the pager in the charger at the end of each day Star Pagers uses the charger 9 CH R9 Programming To program the pager see pg 28 Using the SP5 1 Line Rechargeable Alphanumeric Pager www pager net Gis Charging The SP5 uses the Charger 5 CH R5 1 Place the pager in the charger 2 Allow unit to fully charge overnight 3 Remove from charger pager will vibrate or beep to show it is working 4 LCD will show the pager s ID 5 Replace the pager in the charger at the end of each day Menus To access the vibe contrast menu remove the pager from the charger While vibrating or beeping press and hold the Select button for 8 seconds This top level menu will display Long Range Systems 37 Freedom User Manual SP5 Pager Screen UIBE CONTRAST If you PRESS and RELEASE the SP5 pager button the menu will change to SP5 Pager Screen UIBE COHTRAST To exit this menu wait 8 seconds To re enter the vibe contrast menu at any time reset the pager and then hold the SP5 pager button Vibe To set the Vibration Level 1 Enter the vibe contrast menu as described above 2 Highlight the Vibe selection then PRESS and HOLD the SP5 pager Button until the screen shows 3 Press or hold the Select Button to the
10. 6 am Guest zt Cell Phone Button This key is used to enter the patron s mobile phone number into the T7460 s memory Number Keys Keys 1 through 0 enter numeric data such as the pager number In some modes they will also Promo Ke y enter alphanumeric data Allows entering email addresses for future pro motions Enter Key The Enter key is used to start the paging function and to complete pro gramming where re quired Staff Key Used to temporarily change the paging func tion to page Staff pagers Clear Key Clears the input when paging a pager and re turns to the Guest paging display or to restart an input when programming Initial Power Up and Time Set 1 After the transmitter initializes the set date menu is shown type in the current date Using MM DD YY and press ENTER 2 When the display asks to enter time type in the current time and select F1 AM or F2 PM Long Range Systems 5 Freedom User Manual Basic Paging Operation Guide The following are the most commonly used procedures for paging Make sure that all rechargeable guest or staff pagers are not on the charging unit and all battery operated pagers are turned on Page Guest Pagers Non Alphanumeric AdverTeaser Pizza Lobster Coaster Call pagers 1 Main screen displays Guest 2 Enter number assigned to guest at handout 3 Press ENTER to send page 4 Return guest pagers to charging unit after
11. ABLED Access the Network Menu and verify that the Network is ENABLED If using a DHCP Network verify DHCP is selected as YES If using a Static Network verify DHCP is selected NO then verify the transmitter s IP Netmask DNS and Gateway addresses are entered correctly o 012 C Long Range Systems 33 Freedom User Manual Service Questions and Answers Should your paging system ever fail or should you need additional paging equipment call Long Range Systems at 800 437 4996 or 214 553 5308 24 7 days a week For weekend or night emergencies Long Range Systems has 24 7 live technical support available Please keep in mind that options are limited over the weekend LAS Pagers Available for the Freedom Transmitter 17400 Using the 4 Line Alphanumeric Pager an Gis DOWN SELECT READ BUTTON UP SCROLL DOWN Menus Alphanumeric Pager Screen im 1 UP READ ALL SCROLL 18 25 12 38AM y DN 1 From Read All screen press UP or DN Scroll button until desired selection displays 2 Press Read Select button to select item 3 Press UP or DN Scroll button to choose adjust 4 Press Read Select to confirm set Power On Off Set ON if unit is off 1 Press and hold Scroll Up until YES NO shows 2 At Power ON use UP or DN Scroll button to select YES 3 Press Read Select button to set Long Range Systems 34 Freedom User Manual Set OFF 1 Using the UP or
12. Below 50 is for Star Pagers The default crossover point for Guest Pagers is 1000 1000 and above for Alphanumeric Coasters Below 1000 for Coaster Call and Paddle pagers AdverTeaser To Change the Crossover Points 1 Press SETUP and enter Password 2 Press 1 System 3 Press F2 DN until display shows 1 POCSAG Long Range Systems 22 Freedom User Manual 4 Press 1 1 POCSAG 5 Press F2 DN until 22POCSAG Start is displayed 6 Press 2 POCSAG Start 7 For Guest Alphanumeric Pagers press 1 Guest and type in the new POCSAG start number from 1 9999 8 For Staff Alphanumeric Pagers press 2 Staff and type in the new POCSAG start number 1 9999 Choose number from 1 9999 Press ENTER to keep a default value 50 Station ID Station ID is often confused with System ID This function is used where more than one station of the same establishment may be paging staff pagers The indicators on the pager will show this code To set a different station number 1 Press SETUP and enter Password 2 Press 1 System 3 Press F2 DN until the display shows 3 Station ID 5 Press 3 3 Station ID 6 The display shows the current station ID number default is 1 7 Press a number to use 0 9 to change the default Station ID number and press ENTER Adjust Transmit Power The range may be increased or decreased from the transmitter by adjusting the transmit power level The power levels are 1 through 5 Defaul
13. DN scroll button scroll until display shows Power OFF 2 Press Read Select button to set power on off 3 At Power OFF screen use UP or DN Scroll button to select YES 4 Press Read Select button to set Read Message Alphanumeric Pager Screen l 1 UP READ ALL SCROLL 10725 DN Messages are displayed upon receipt Press Read Select to display To Review Stored Messages 1 Select Read AII 2 Press Read Select to display messages and time stamps 3 Use the UP or DN Scroll button to scroll through messages Delete Messages 1 Using the UP or DN scroll button scroll until display shows Delete AII 2 Press Read Select 3 Use the UP or DN scroll button to select Yes or No 4 Press Read Select button to confirm Time Date Set 1 Using the UP or DN scroll button scroll until display shows Set Time Date 2 Press Read Select to set time date 3 Press UP or DN scroll button to set each time or date segment and press Read Select to move through the segments Set Contrast 1 Using the UP or DN scroll button scroll until display shows Set Contrast 2 Press Read Select 3 Use the UP or DN scroll button to adjust 4 Press Read Select to confirm Auto ON OFF 1 Using the UP or DN scroll button scroll until display shows Auto ON OFF 2 Press Read Select to set auto on off 3 Use the UP or DN scroll button to select On or Off Long Range Systems 35 Freedom User Manual
14. ENTER OR Press F1 KEEP to use the existing number Note Entering pager number 911 will page all Alpha pagers Long Range Systems 14 Freedom User Manual Feature Setup Procedures User Password All of the functions that adjust paging preferences are protected by a Password To reduce tampering with critical settings the keypad is password protected The Password 56789 allows you to enter most restricted programming screens Press F4 at any menu to return to the Guest menu Set Manager Password To change the Manager Password 1 Press SETUP and enter Password 2 Press F2 DN 3 Select 3 Manager Password 4 Type in new 5 digit Manager Password and press Enter Set Page Mode This programs how guest and staff pagers will respond when paged Guest pagers can flash beep glow flash and beep etc To set the modes 1 Press SETUP and enter Password 2 Press F2 DN 3 Select 1 Page Mode 4 Select 1 1 Guest or 2 2 Staff Guest Pager Select A Note An asterisk next to a mode indicates that is the current Paging Mode Press 1 Flash Beep Glow Select a page Mode 1 Flash 30 sec 2 Flash 5 mins 3 Beep Flash Press F2 DN 1 Flash 1 sec 2 Glow 15 times 3 Glow 5 mins Press F2 DN 1 Beep 3 times 2 Beep continuously Long Range Systems 15 Freedom User Manual To turn Alphanumeric Guest Paging Vibration On or Off Select 2 Alphanumeric Vibe Press F1 yes to turn Alphan
15. FREEZDOM T7460 Paging System Transmitter USER MANUAL Long Range Systems Inc 4550 Excel Parkway Suite 200 Addison TX 75001 800 437 4996 214 553 5308 WWN pager net Table Of Contents Compatible Pagers Installation and Se VU Di eea ak wa end ox ox dae Gate eo oe RG e ede eG PUR ATI Reo a Hardware Provided seeeeeeeee rns Installation Procedure ius cdo vid oe eee cede mg we de ERE wor iiaea er Rss d Connections Keypad Description xinoizvceme vase beatae ce deed tad ce bad egedeeesoss Initial Power Up and Time Set 0 0 cece eee eee eee eee eens Basic Paging Operation Guide ase esama ee eeu ba et eehGSdheny PEMA EEO Page Guest P AGI OLS ote csraz stot pavo guten HAGA evatean set aures rr oU Rura eee alae AER Page Individual Staff Pagers 0 c cece teen eens Page a Cell Phone lees Canned or Special Alphanumeric Messages eee Canned Message seller hs USB Keyboard Operation 0 eects Special Functions Theft Deterre Tracking MEI UMCTON pecas ta cde secte repere teuer cBICeME Sede tS CUSTOM TRACKING xe ure estet re ee eds Rane ot e eR eee Na BE Sand Rd Group PAGING iad x aues Rak Vt een Ripe ec ect Red TR EC e Du Reine whe ned RR Ad iw Wee E Dry Contact Set Alarms Feature SECU PPO Od UNOS cae dein wee ned E RR ded ane ee wed BRL ar Dod A e he RR User Password deiu eese utu
16. Message 6 Type a number 00 99 for selected canned message and press ENTER Note See pg 16 for Creating Alphanumeric Messages Freeform Guest Message When the Freedom Transmitter pages Guest Alpha pagers the user is given a default message and the abil ity to add an extension example 035125 Table Ready 125 The user can select to have a Freeform message when they control what is entered and if the message can be edited Features for editing guest messages can be accessed by 1 Press SETUP and enter Password 2 Press 1 System 3 Press F2 DN until screen shows 1 POCSAG 4 Press 1 POCSAG Display the Guest and Staff Prompt When paging Guest or Staff Alpha Pagers the user is shown a prompt Freedom Transmitter screen Display SELECT PAGE MODE MSG 835 OUT TABLE READY EXIT To Enable or Disable Seeing This Prompt While Paging 1 Press SETUP and enter Password 2 Press 1 System Press F2 DN until screen shows 1 POCSAG Press 1 POCSAG Press F2 DN until screen show 1 Disp Prompt o 0 P W Press 1 Disp Prompt 7 Press F1 YES to display or F4 NO to not display If Display Prompt is disabled the message sent will default to the Guest Message Long Range Systems 19 Freedom User Manual Turning ON OFF Canned Messages in Guest Display Prompt Note For this feature to be used with Guest Paging Display Prompt must be enabled See pg 18 To write Freeform messa
17. NT UE EUS TEE Pd we EEEE Rupee Rees E Set Manager PassWwOEFd s ouckedzesLnretxEeeuwesceiemdicgLtren ssiahcepcvezuu Set Page Mode llle ehh Set to Page Staff or Guest Pagers 0c ccc eens Create Alphanumeric Messages 0 0c cee cece eee ene ene eens Setting Syste m Time Date for Freedom Transmitter T7460 Alphanumeric Pager Button Enable Disable lees Guest Message nlrdse eccledielere bdedateteldbad eigens bead oe mes Freeform Messages 000 e cece eee ehh hr Alpha Vibration Level 5222 ur edet Fae tt awe ae eee eas RE Ga eels Display the Prompt 0 2 cece eee Turning ON OFF Canned Messages in Display Prompt sss Long Range Systems Freedom User Manual Editing Canned Messages in Display Prompt leere 20 Freeform Staff Message lese hrs 20 Display the Staff Prompt 0 cece eee KE ea Kia Ea nes 21 Staff Message 0 ccc ee eee hrs 21 Turning ON OFF Canned Messages in Staff Display Prompt 21 Editing Canned Messages in Staff Display Prompt 000 eee eee ene 22 Maintenance FUTGEIQTS aca eevee eee hy eee READ Gh OTe Rae ees 22 Paging Types in Mixed Systems 000 cece eee eee eee eens 22 cupnibE MELDE 23 Adjust Transmit Power secca sented niaaa eaa aaa hn 23 Locating Misplaced Pagers csse 23 Cell
18. ON enter a starting Time of Day for Auto Location HH MM Press F1 AM or F2 PM MH Oo 0i P O0 NM If turning function ON 8 Enter Start Time for Auto Location and press ENTER to continue 9 Press F1 AM or F4 PM Run Locate Mode Run locate is used to immediately locate any misplaced coasters around the restaurants ideal during clos ing hours When activated Asignal is sent out to ALL guest pagers Pagers will Beep or Flash until returned to charging unit or batteries removed To activate 1 Press SETUP and enter Password 2 Press 3 OTHER 3 Choose 3 Locate Pagers 4 Press ENTER to begin locating pagers Long Range Systems 24 Freedom User Manual Cell Phone Paging Overview The Cell Phone interface is used to extend the capability of the on premise paging system When a Guest s Cell Phone number is entered the transmitter will store the number as a Pager Number be tween 500 and 599 System Requirements Cell Phone Paging requires broadband internet service a CAT 5 Ethernet cable and an activated account with Long Range Systems Two Steps to enable the Cell Phone Paging Step 1 1 Disconnect power to the T7460 Connect the CAT 5 cable to the Ethernet port Re connect power to the T7460 Press SETUP and enter Password Press 1 System Press 2 Cell Phone Paging Press 1 Enabled When asked to Enable voice SMS paging press F1 Yes or F4 No Exit Step
19. PF WN Place pagers in charger Complete the Steps for Programming Individual Pagers At the Select Type menu press 2 2 Staff At Enter ID enter the number you wish to assign to the Pager Remove the Pager from the charger At the screen display Reset Pager When Pager Stop press ENTER The pager will Vibrate and or Beep When the Vibration Beeping Stops press ENTER again The Pager will beep three times to indicate it is being programmed and the screen will display Example System ID 0 Pager ID Number 99 All Page 911 Prg C1 0 99 Prg C2 0 911 Long Range Systems 28 Freedom User Manual 10 11 12 13 Prg C3 0 0 Return the Pager to the Charger when Programming is complete Repeat Steps 2 through 10 for the remaining Pagers When finished remove Pagers from the Charger and Page each one Reprogram any Pagers that do not page Staff Pagers Battery Operated Alpha Pagers This procedure i is repeated for each pager being programmed Note Staff Alpha Pagers numbers must be above POCSAG start oO ON OOO B CN 10 11 Repeat the programming procedure for any pagers that do not page Turn all of the Pagers Off or remove batteries Complete the steps for Programming individual Pagers At the Select Type menu press 2 2 Staff At Enter ID enter the number you wish to assign to the Pager Turn the Pager Off and then On or reins
20. Prone TUM 25 OVEIVIEW x zusenden Sle M Dare Rea x bed Gad Ae bed Ga tee ee ede 25 System Requirements 0 ccc eee eee ern 25 Cell Phone Status soe tineri Ta mi ninia ai ai iiia k panii Ag iik o iai Eee D 26 Program ming Paene viaiacarvidavs VR xm diuk x RS dE e RR d 21 Individual Pagers se nesini da secet rends uisus ated a ir a dud ee RE ee UR s 27 Program Pager Groups 00 c cece eee ehh 29 Alpha Encry pum 22m 60 yd cian geome eee a mus deo eee Rhee ae ee d 30 Program Pager Vibration 0 0 0c rn 31 Program Welcome Message 0c cece ete eee lee 31 System Specifications sis aw aw das bale wae Bony eos ane hea wa Wd a Mae a 32 TRANSMIMGN 208 rr 32 Battery Powered Pagers 000 c cece eee eee ete eee 32 Rechargeable Pagers oett eeu t Kae eae ee ead Baad Sa Sees 32 TOUTES HOO RING soli inia s aeq ue ed ee ee oe e eR aa ea RU ERROR a d 33 Display Shows Nothing cece cece e eee eee hn 33 Pagers Do Not Receive Pages 0s cece eee tenes 33 My Cell Phone Paging Is Not Working 0 cece eee eee eee etnies 33 Service QUeStiOnS dnd ANS Ors ranci adats uk a bbe eee ea 4 AER RR RR RT Rad 34 LRS Pagers Available for the Freedom Transmitter T7460 005 34 Using the 4 Line Alphanumeric Pager 0 e eee eee eee 34 Using the Star Pager xus tree t cede heal ews wee eed ha Re Ga ea 37 Using the SP5 1 Line Rechargeable Alphanumeric Pagers 37 Usi
21. R 3 Press F1 YES to send all page or F4 NO to cancel 4 Enter a message of 1 9 5 Press ENTER to send the page OR 6 Choose F1 V1 F2 V2 F3 V3 or F4 Exit to send 1 2 or 3 vibrations Page a Cell Phone 1 Press Cell Phone and type in guest s cell phone number then press ENTER aa Record the Pager number that appears on the screen V Note Pager number 500 599 are reserved for Cell Phone Paging 3 When the customer s table is ready at the Guest Screen enter the pager number assigned to the customer Canned or Special Alphanumeric Messages Using Message Codes When prompted for a message on the Freedom Transmitter T7460 1 Enter message number code and an extension number optional 2 Press ENTER Example Send a message to call extension 123 From Canned Message Table choose 006 Call Ext Enter code 0 0 6 1 2 3 Displays CALL EXT 123 v EXTENSION A ____ 006 MESSAGE Note These non editable messages are built into the transmitter If using Alphanumeric pagers ad ditional messages can be created see Create Additional Alphanumeric Messages on pg 16 See next page for table of canned messages Long Range Systems 7 Freedom User Manual Canned Message Code 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 Message Phone Call Sales Call Manager Customer Room Visitor Call Ext MTG Room Lane Aisle
22. Void Stamps Change Station Machine Operator Emergency XX Minutes Tee Pro Shop USB Keyboard Operation A USB Keyboard can be plugged into the Freedom Transmitter to allow data entry F1 F4 keys function as F1 F4 keys on Freedom Transmitter Keypad selecting menu options F8 toggles between Staff and Guest Paging A Z 1 10 and characters operate as normal Shift Key works to change character F5 will enter Cell Paging Menu cell phone paging must be turned on Ctrl S the Setup Menu 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 Starter Service drive Showroom Parked Call Voice Mail Dressing room Price check Department Cashier Office Table Winner Pickup Dock You have mail Table ready No special Hole Kitchen Bar Arrow Keys can be used to move the cursor Escape ESC will exit the current view Enter ENT will accept the current entry F12 will enter Promo Email Entry Menu Cell Phone Paging must be turned on Long Range Systems 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 Door Survey T nnn O mm Break Fire Unit Window Nurse Register Owner Check Drink Food Service Seat Booth Lobby Help Restroom Valet 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 Car Bus Bay Low battery Error Exit Fax host Space Location
23. been made to make the information in this document complete and accurate LRS is not responsible for any direct or indirect damages or loss of business resulting from inaccuracies or omissions Specifications and other information contained within this document are subject to change without notice Long Range Systems Inc reserves the right to make changes without further notice to any products herein LRS Inc makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does LRS Inc assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters that may be provided in LRS Inc data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts LRS Inc products are not designed intended or authorized for use as components in sys tems intended to support or sustain life or for any other application in which the failure of the LRS Inc product could create a situation where personal injury or death may occur Should Buyer purchase or use LRS Inc products for any such unintended or unauthorized application Buyer shall indemnify and hold LRS Inc and
24. default duration is 90 seconds The duration can be set for 0 3600 seconds To Set the Duration 1 Press SETUP and enter Password 2 Press 1 system 3 Press F2 DN until display shows 2 Tracking 4 Press 2 5 Select 2 Duration 6 Type in a new time in seconds and press ENTER A Note Entering 0 will make the Duration run Forever Long Range Systems 10 Freedom User Manual Interval The Interval defines how many seconds of time passes between pages The default Interval is 10 seconds The Interval can be set from 10 255 seconds To set the Interval 1 Press SETUP and enter Password 2 Press 1 system 3 Press F2 DN until display shows 2 Tracking 4 Press 2 5 Select 3 Interval 6 Type in a new time in seconds and press ENTER DURATION 0 3600 Seconds INTERVAL 10 255 Seconds ZO oFFTME NN coe CREE OFF TIME e Group Paging General Purpose This function is used with Alpha pagers These pagers can be programmed to respond to group calls Ten groups are available and each pager can be a member of 5 groups Each pager will respond to its individ ual number and to any groups it belongs to See example below Group Paging Rules General rules for paging groups are Pagers must be programmed in the group mode Staff pagers must be numbered above 100 1 99 are reserved for groups Any alphanumeric pager can be a member of up to 5 groups Long Range Systems 11 Freedom User Manua
25. desired vibration level The level will rise to max Release the Select Button and press or hold again until the level goes to minimum or desired level 4 To exit wait 8 seconds And the pager will go back to the vibe contrast menu SP5 Pager Screen UIBE SP5 Pager Screen WIBE CONTRAST Contrast To set the Contrast Level 1 Enter the vibe contrast menu as described above 2 Highlight the Contrast selection then PRESS and HOLD the SP5 pager Button until the screen shows Hl 3 Press or hold the Select Button to the desired Contrast The level will increase to max NOTE screen could be dark and hard to read Release the Select Button and press or hold again to change the level back towards the minimum or to desired contrast 4 To exit wait 8 seconds And the pager will go back to the vibe contrast menu SP5 Pager Screen WIBE SP5 Pager Screen UIBE CONTRAST 5 To exit this menu wait 8 additional seconds Long Range Systems 38 Freedom User Manual Settings To view the current pager settings 1 Remove pager from the charger or reset on the T9601 T9100 or T9101 reset terminals 2 Press the Select Button repeatedly to scroll through the settings C1 System ID number and Pager ID number C2 System ID number and All Page number C3 System ID number and System ID number G Group number Enc Encryption enabled 128 or none Ver Current Firmware Version 3 To exi
26. e empty Pad dle pagers may be replaced into the same slot in the charger 2 Complete the steps for programming individual Pagers 3 At the Select Type menu press 1 1 Guest Pagers 4 Enter Pager Number and press Enter 5 Select Pager type 1 Coaster Page or 2 Paddle Pager 6 Select if Pager should Vibrate F1 Yes or F4 No 7 Remove the guest pagers from the charger 8 When flashing stops press ENTER 9 The coaster pager will slowly vibrate and light up then dim to off to indicate it is being pro grammed 10 When programming is finished put the coaster on the second charging base or the Paddle pager back into its slot 11 Repeat steps 2 through 10 for the remaining coasters pagers 12 When finished remove all of the coasters pagers from the charging base and page each one 13 Reprogram any that do not page Guest Alpha Coasters This procedure is repeated for each pager being programmed Two charging bases are suggested for pro gramming Alpha Coasters Note Guest Alpha Pagers numbers must be above POCSAG start 1 Put all coasters to be programmed on one charger base leave the second base empty 2 Complete the steps for programming individual Pagers Long Range Systems 27 Freedom User Manual NO 0 P CO At the Select Type menu press 1 1 Guest Pagers Enter Pager Number and press ENTER Remove the coaster from the charger When flashing stops press ENTER The pager wi
27. elect to have a Freeform message when they control what is entered and if the message can be edited Features for editing Staff Message can be accessed by 1 Press Setup and enter Password 2 Press 1 System 3 Press F2 DN until screen shows 1 Manager Msg 4 Press 1 Manager Msg Long Range Systems 20 Freedom User Manual Display the Staff Prompt When paging Staff Alpha Pagers the user is shown the prompt Freedom Transmitter screen Display SELECT PAGE MODE MSG 835 OUT TABLE READY EXIT To enable or disable seeing this prompt while paging refer to pg 20 Staff Message The Staff Message is the default canned message sent to Staff Alpha pagers To change the message 1 Press Setup and enter Password 2 Press 1 System 3 Press F2 DN until screen shows 1 Manager Msg 4 Press 1 Manager Msg 5 Type number 00 99 for selected canned message and press ENTER Note See pg 16 for creating Alpha Messages Turning ON OFF Canned Messages in Staff Display Prompt Note For this feature to be used with Staff Paging Display Prompt must be enable See pg 20 To write Freeform messages using 0 9 keys or USB Keyboard into the Display Prompt Canned Messages will need to be disabled To Enable or Disable Editing 1 Press Setup and enter Password Press 1 System Press F2 DN until screen shows 1 Manager Msg Press 1 Manager Msg Press 2 Use Canned Msg oOo 01 A UN A
28. ents 2 Twist the 3 antenna onto the silver connector located on the rear of the transmitter 3 Plug the power adapter into a standard 110 220V outlet and insert the barrel connector end into the port located on the rear of the antenna 4 Upon completion of setup make sure pagers are fully charged and or have good batteries and are powered on 5 The systems are shipped ready for the most general use If you need to modify settings refer to the table of contents to locate a specific function guideline Connections The following diagram shows the system connections NETWORK ETHERNET CABLE 10 VAC ELECTRICAL SUPPLY 10 VAC POWER ADAPTER ANTENNA KEYPAD TRANSMITTER ll FREEDOM C OCOCOCOCOCOCOCOCOCOCOCOCOCO DLgs ee JEJE JE JEJE JE JL ee eee Cc C JODODUODOGCCDCDCOLI T li s Bd or SEE eee ae L us Keyboard Optional Long Range Systems 4 Freedom User Manual Keypad Description Before using the keypad read the following keypad descriptions Note As the display changes the keys may perform different functions Setup Key F Keys The Setup key enables menus when checking or changing the transmitter s programmed settings The F function keys are the first row of keys under the display The F1 F4 keys correspond to the bottom row of text in the keypad display window 12 00 3
29. f the selected alarm Select Change F1 to en able disable or modify the alarm A Note f the alarm is already enabled as an interval alarm Press F1 YES to reset the timer and return to the paging menu Press F4 NO to continue to the ON OFF menu 7 At Enable menu select F1 YES to enable the alarm or F4 NO to disable the alarm 8 Select the type of alarm 1 Interval 2 Daily or 3 Weekly Interval Alarms are alarms that re page a staff pager at regular intervals 1 Enter the desired time interval in hours and minutes HH MM and Press ENTER Long Range Systems 13 Freedom User Manual 2 Enter pager number to be alerted 3 Type in canned message See Table on pg 8 and press ENTER Daily Alarms are alarms that re page a staff pager at a particular time every day 1 At the Time of Day menu enter the time for alarm 2 Select F1 AM or F2 PM 3 Type in pager number to be alerted and press ENTER 4 Type in canned message See Table on pg 8 and press ENTER Weekly Alarms are alarms that will page a staff page on a certain day of the week 1 Select the Day of Week to page Use F2 DN to scroll through Wednesday through Saturday 2 Enter the Time of Day HH MM for the alarm 3 Press F1 AM and F2 PM 4 Type pager number to page and press ENTER 5 Type in canned message See Table on pg 8 and press ENTER 6 At Set pager Number menu either Enter the number of the pager to be alarmed followed by
30. ge Note Long Range Systems must setup the SMS Text or Voice Message before this feature can be used Ifthe user wishes to change the Message or type of message contact Long Range Systems Cell Phone Status To view the current link status of the Freedom Transmitter 1 Press SETUP and enter Password 2 Press 1 System 3 Press 2 Cell Phone Paging 4 Press 3 Status 5 The screen will now show the current Cell Status If the Status is OK then the link is successful Long Range Systems 26 Freedom User Manual Programming Pagers Pager numbering and mode setup is used to renumber or set up individual pagers Note Be sure to refer back to Paging Types in Mixed Systems section to ensure that pagers are programmed using appropriate crossover points Individual Pagers Note Rechargeable pagers can have their System ID s changed or their vibration turned on or off as a group 1 Press SETUP and enter Password 2 Press F2 DN 3 Press 1 1 Program 5 Press 1 1 Prg Pager 7 At the Select Type menu select the basic type of pager you are re programming Guest pagers or Staff pagers Non Alpha Guest Pagers AdverTeaser Paddle Pager Coaster Pager Pizza Pager Lobster Call This procedure is repeated for each pager being programmed Two charging bases are suggested for pro gramming Coasters Pizza pager Lobster Call 1 Place all guest pagers to be programmed on one charger base leave the second bas
31. ges using the 0 9 keys or USB Keyboard into the Display Prompt Canned Messages will need to be disabled To Enable or Disable 1 Press SETUP and enter Password Press 1 System Press F2 DN until screen shows 1 POCSAG Press 1 POCSAG press F2 DN until screen shows 2 Canned Msg Press 2 Canned Msg MH Oo oh FP CQ M At prompt to Use Canned Msg press F1 YES to keep Canned Messages or press F4 NO to allow Freeform Messages Editing Canned Messages in Guest Display Prompt The user has the option of locking the Canned Message part of the Guest Display Prompt Note 7o change the Canned Messages see Guest Messages on pg 19 Example If the user has Canned Messages Enabled and Edit Message Enabled in the Display Prompt of 035 123 Table Ready 123 ONLY the 123 portion of the message can be changed e g to 035 456 or another number to display Table Ready 456 To Enable or Disable Editing 1 Press SETUP and enter Password Press 1 System Press F2 DN until screen shows 1 POCSAG Press 1 POCSAG Press F2 DN until screen shows 3 Edit Msg Press 3 Edit Msg At prompt to Edit Canned Message press F1 YES for editing or F4 NO to disable editing N Oo Oh PR CO M Freeform Staff Message When the Freedom Transmitter pages Staff Alpha pagers the user is given a default message and the abil ity to add an extension example 035125 Table Ready 125 The user can s
32. is will also damage the equipment and is not covered under the standard warranty Charging Place rechargeable pagers on the charger and let them charge for 8 hours prior to first use Rechargeable pagers should be kept on charge even during extremely long periods of inactivity Only 10 VAC power supplies should be used with LRS chargers and transmitters DC power supplies will cause damage to equipment that is not covered under the standard warranty Should you have any questions please contact the LRS Customer Service Department at 800 437 4996 214 553 5308 or your local LRS dealer LRS Australia LRS Brazil LRS Canada LRS Colombia 61 02 995 5700 5511 41528416 877 607 7243 57 1 7592452 www Irsaustralia com au www Irspager com br www Irscanada ca www Irscolombia com LRS Europe GmbH LRS Middle East Ltd LRS South Africa LRS United Kingdom 49 531 310542 0 9613 81 82 84 27 21 422 4975 44 0 1782 537000 www lrs eu com www lrs Ib com www lIrssa com www Irspagers co uk Long Range Systems 41 Freedom User Manual Warranty Long Range Systems Inc warrants this product against any defects that are due to faulty material or workmanship for a two year period after the original date of consumer purchase The warranty does not include damage to the product re sulting from accident misuse improper electrical connection or failure to charge the product within 30 days of receipt Rechargeable pagers are required to stay on charge while not in
33. l Paging Groups 1 Enter the number for the pager or the group If only paging staff pagers and have the transmitter default set to Pager enter the pager or group number directly If paging default is set to Guest press Staff before entering the pager or group number 2 Enter the message to send 3 Press ENTER To Turn Group Paging On Off 1 Press SETUP and enter the Password 2 Press 1 System 3 Press F2 DN until display shows 2 POCSAG 4 Press 1 Groups Enabled 5 Select 2 Group Paging 6 Press F1 Yes or F4 No Dry Contacts The Dry Contact are contacts or switches that are connected through a wire to the T7460 for example Door bell This sensor can send a message to the pager when an event occurs e g alarms if a door is opened Default setting for the Contact Sensor is OFF To program the Contact Sensor Dry Contact 1 Press SETUP and enter the Password 2 Press F2 DN until the display shows 1 Dry Contact 3 Select 1 1 Dry Contact 4 At the Contact Menu screen select 1 1 Prog Contacts 5 Select contact to program press 1 1 Contact 1 or 2 2 Contact 2 6 The Screen will show if Contact Sensor is currently on or off Press F1 to turn the function ON Press F2 to turn the function OFF 7 If select ON select for the sensor to set as Press F4 for Normally Closed this is the default setting Press F1 for Normally Open 8 Enter the pager number that will be pager whe
34. ll beep four times to indicate it is being programmed and the screen will display Example System ID 0 Pager ID Number 99 All Page 911 01123 prg Single 0 911 prg All Page 0 O prg System Repeat steps 2 through 7 for the remaining coasters 9 When finished remove all of the coasters from the charging base and page each one 10 Reprogram any that do not page Staff Pagers Star Type This procedure is repeated for each pager being programmed Pagers may be replaced into the same slot in the charger 1 Complete the steps for programming individual Pagers 12 Place all Pagers to be programmed in the charger 2 3 At the Select Type menu press 2 2 Staff 4 At Enter ID enter the number you wish to assign to the Pager and press ENTER 5 6 7 8 Select if Pager should Vibrate F1 Yes or F4 No Remove the Pager from the Charger When the Flashing Stops press ENTER The Pager will slowly Brighten and Dim to Off to indicate it is being Programmed 9 10 11 Reprogram any that do not page When Programming is finished return the Pager to its Charging Base Repeat Steps 1 through 9 for the remaining Pagers When finished remove all of the Pagers from the Charging Base and Page each one Staff Pagers Rechargeable Alpha Pagers This procedure is repeated for each pager being programmed Note Staff Alpha Pagers numbers must be above POCSAG start oO AON Oa F
35. n this event occurs Pager Num and press ENTER 9 Enter a User Message Press F2 to create a new message use the 1 9 keys to enter the text and then press ENTER to Save Press F1 to edit the current message 10 Select paging type mode F1 STAFF F4 GUEST 11 Press F4 to EXIT een T7460 Back View leecocceo y USB Power Antenna Ethernet Dry Contacts Long Range Systems 12 Freedom User Manual T7460 Dry Contact Specifications Input Voltage 0 5 Volts DC Contact Diameter 2 5mm Contact Type Mono Plug T7460 Dry Contact Cable Specifications Contact Diameter 2 5mm Contact Type Mono Plug Number of Conductors 2 Ring Connection Positive Tip Connection Ground ami x aL ae I SINGLE STRIPE OF MONO PLUG CONNECTION 2 5 MONO PLUG WIRE r SHIELD e i WHITE WIRE Set Alarms This function is used to set the transmitter to page an individual or all STAFF pagers at a specific time or on a timed interval The transmitter can send 10 different time alarms or periodic alarms Alarms may be set to page a specific pager or all pagers at a specific time every day 1 Press SETUP and enter Password Press 1 System Press F2 DN until display shows 3 ALARMS Select 3 3 ALARMS From the Alarm menu select the number of the alarm to set 0 through 9 and press ENTER o 01 A O hM The Alarm Display screen shows the status o
36. ng the Non Alphanumeric Guest Pagers llle 39 Using the Alphanumeric Coaster Guest Pagers llle 40 Cleaning amp Charging Instructions for LRS Paging Equipment 41 eH Rs I amp we at ote eee Geena PITT 42 Long Range Systems 2 Freedom User Manual Compatible Pagers Customer Pagers Coaster Call Alphanumeric Coaster AdverTeaser Paddle Pager Lobster Pager Long Range Systems Staff Pagers www pager net SP5 1 Line Rechargeable Alphanumeric Pager Star Pager RX E 4 Line Alphanumeric Pager Battery Operated Freedom User Manual Installation and Setup Hardware Provided The system contains the transmitter keypad an instruction booklet an antenna a strip of Velcro rubber feet and a 10 VAC power adapter Notice Operation is subject to the following This device may or may not cause interference This device will accept any interference including interference that may cause undesired oper ation of the unit Notice To reduce potential radio interference to other users the antenna type and gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than required for successful communication Installation Procedure The following is the basic installation procedure Ny CAUTION Do not mount the transmitter antenna near any large metal objects 1 Un wrap all system compon
37. paging Alphanumeric Alphanumeric Coaster pager 1 Main screen displays Guest 2 Enter number assigned to guest at handout then press ENTER 3 Enter message code 000 099 see Canned Messages Table pg 8 4 Press ENTER to send page 5 Return guest pagers to charging unit after paging Page Individual Staff Pagers Non Alphanumeric Star Pager 1 On keypad press STAFF Display will show Pager 2 Enter staff pager number to be paged then press ENTER 3 Press ENTER to send page OR 4 Press F1 V1 F2 V2 or F3 V3 for 1 2 or 3 vibrations Alphanumeric Alphanumeric Rechargeable alphanumeric pagers 1 On keypad press STAFF Display will show Pager 2 Enter staff pager number to be paged then press ENTER 3 Enter message code 000 099 see Canned Messages Table pg 8 4 Press ENTER to send page OR 5 Press F1 V1 F2 V2 or F3 V3 for 1 2 or 3 vibrations All Call Page Page all guest pagers simultaneously At Guest Screen Display 1 Enter 000 then press ENTER Long Range Systems 6 Freedom User Manual All Staff Alpha Page Page all staff pagers simultaneously 1 Press STAFF 2 Press 9 1 1 then ENTER 3 Enter message number code 000 099 see Canned Messages Table pg 8 4 Press ENTER to send page OR 5 Choose F1 V1 F2 V2 F3 V3 or F4 Exit for 1 2 or 3 vibrations All Staff SP4 Page 1 Press STAFF 2 Type 0 0 0 then ENTE
38. paging based on a user defined interval and run time setting The pager number is cleared on the keypad unit when run time is complete or when user clears the number by press the Function Key F1 F4 under the number To turn Tracking on or off 1 Press SETUP and enter Password 2 Press F2 DN until screen displays 3 Tracking 3 Select 2 Tracking 4 Select 1 Enable PAGERS IN 5 Press F1 YES or F2 NO THE QUEUE Transmitter Tracking Screen 18 34 56 PM GUEST 2 To Use Tracking CANCELS CANCELS CANCELS SCROLLS STAFF 99 GUEST 82 STAFF 92 THROUGH PAGER LIST 1 Page the guest or staff pager using the basic paging procedure 2 The pager number will appear at the bottom of the screen signifying that the pager is being paged 3 When the page has been received and acknowledged clear the page by pressing the F1 F2 or F3 key under the pager number shown on the keypad display If more than 3 pagers are in the queue gt will be shown at the right of the display Press F4 to see the rest of the list Custom Tracking Tracking Intervals The tracking feature can be set to a user defined duration and paging intervals Duration The Duration is the total amount of time the repeated pages will continue for in seconds For example if you choose 120 seconds the Freedom Transmitter T7460 will continue to page at the pre defined interval until the overall 2 minutes 120 seconds is timed out The
39. roximately 12 48 hours depending on usage Recharge Time Typically 8 hours depending on usage 24 hours minimum from completely dead Long Range Systems 32 Freedom User Manual Troubleshooting Display Shows Nothing Be sure power supply is plugged in f yes Be sure power supply is good Substitute the transmitter power supply with the charger supply Be sure the outlet circuit is on Unplug and re plug a few times to be sure the unit doesn t need a reset If no plug it in Remedy If power supply is good call LRS to troubleshoot further If power supply is bad call LRS to order a power supply Pagers Do Not Receive Pages Be sure pagers are ON Awake Charged or have Good Batteries Try paging more than one pager to be sure it s not a faulty pager Battery Powered Pagers Don t Receive Pages 1 Be sure the pager is turned on and that the battery is good 2 If pagers do not turn on replace battery and retry 3 If pagers do turn on and still do not receive a page check transmitter If pagers continue to not receive pages contact LRS My Cell Phone Paging Is Not Working 1 Do you have an account setup with Long Range Systems for a voice SMS messaging service If Yes proceed to Step 2 2 Check Network cable and make sure both ends are plugged in Green Light will be lit and the Or ange Light should blink to indicate connectivity Access the Cell Paging Menu and make sure Cell Paging is EN
40. t wait 8 seconds Messages The pager stores the last 5 received messages To view the messages 1 Press the Select Button once 2 Messages 2 lines in length will show a gt symbol on the end of the first line and a lt on the second line Messages over 2 lines in length the middle lines willshow lt the next line of the message gt 3 Press the Select Button to continue scrolling forward through the message or messages Time Pager will display the current time The Freedom Transmitter T7460 automatically updates this feature If the time does not appear a flashing star will appear on the right side of LCD to show pager is operational Programming To program the pager see pg 28 Using Non Alphanumeric Guest Pagers Charging Any rechargeable guest pager will require use of an LRS charger 1 Place the guest pager in the charger For 15 Coasters 10 Pizza pager and 10 Lobster call pagers Do not stack more than 10 pagers at a time on a Charger 2 Allow unit to charge fully overnight 3 Remove from charger and pager will vibrate beep and light all lights as a verification that it is working 4 Replace the pager in the charger at the end of each day Long Range Systems 39 Freedom User Manual The pagers all use different chargers Coasters use the Charger 8 CH R8 AdverTeasers and Star Pagers use the Charger 9 CH R9 Lobster Pagers use the Lobster Charger CH LP Pizza Pagers use the Piz
41. t from the factory is power level 3 Reset only by direction from LRS To set the power level 1 Press SETUP and enter Password 2 Press 1 System press F2 DN until the display shows 2 Transmit Power 5 Press 2 2 Transmit Power 6 Set the required power level from 1 through 5 7 Press ENTER Locating Misplaced Pagers Two location modes are available for finding lost or misplaced pagers coasters Auto Locate Mode auto matically searches at a preset time Run Locate Mode searches on demand W caution Do not set auto locate to run or use Run Locate feature while pagers are handed out All pagers will be paged Auto Locate Mode Auto Locate sends a signal to ALL coasters pagers at a preset time The coasters pagers will beep so that staff can locate them Example If closing at 11 30PM the transmitter can be set to auto locate at 12 30AM causing all miss ing coasters pagers to beep at that time Long Range Systems 23 Freedom User Manual When activated A signal is sent out to ALL coaster pagers Pagers will Beep or Flash until the pagers are placed on the charging unit or the batteries go dead In the case of battery operated pagers the battery must be removed to stop the beeping To activate 1 Press SETUP and enter Password Press 3 OTHER Press F2 DN Choose 1 1 Auto Locate to program auto locate Press F1 YES to turn Auto Locate mode on or press F2 NO to turn off If turning function
42. t prompt to Use Canned Msg press F1 YES to keep canned Messages or F4 NO to allow Freeform messages Long Range Systems 21 Freedom User Manual Editing Canned Messages in Staff Display Prompt The user has the option of locking the canned message part of the Staff Display Prompt Note 7o change the Canned Messages see Guest Messages on pg 19 Example If the user has Canned Messages Enabled and Edit Message Enabled in the Display Prompt of 035 123 Table Ready 123 ONLY the 123 portion of the message can be changed e g to 035 456 or another number to display Table Ready 456 To Enable or Disable Editing 1 Press Setup and enter Password 2 Press 1 System 3 Press F2 DN until screen shows 1 Manager Msg 4 Press 1 Manager Msg 5 Press 3 Edit Msg 6 At prompt to Edit Canned Msg press F1 YES for editing or F4 NO to disable editing Maintenance Functions W caution The following features are not normally adjusted unless directed by LRS Paging Types in Mixed Systems When using different types of pagers be sure that alphanumeric pagers are numbered higher than the non alphanumeric pagers Setting Crossover Points This function is used to set the crossover points where non alphanumeric end and alphanumeric pagers begin Crossover points must be set using the following rules The default crossover point for Staff Pagers is 50 50 and above are Alphanumeric Pagers
43. tall the battery At screen display Reset Pagers When Pagers Stop press ENTER It will Vibrate and or Beep When the Vibration Beeping Stops press ENTER again The Pager will beep three times to indicate it is being Programmed and the screen will display Example System ID 0 Pager ID Number 99 All Page 911 Prg Single 0 99 Prg All Page 0 911 Prg System 0 0 Repeat Steps 2 through 9 for the remaining Pagers When you re finished programming send a test page to each pager Program Pager Groups Group Paging must be enabled Note Only LRS pagers can be assigned groups and be programmed from the transmitter 1 Turn all Pagers Off or remove batteries or Place unit in Charger 2 Complete the steps for individual Pagers 3 At select type menu press 2 Staff 4 At enter ID enter the number you wish to assign to the Pager 5 6 7 8 At enter Groups enter the Group Numbers you which to assign the Pager to and press ENTER Turn Pager or Remove pager from charger At screen displays Reset Pagers When Pagers Stop press ENTER The Pager will beep three times and additional beeps for each Group Number and Group Name assigned Example System ID 0 Pager ID Number 99 All Page 911 Group 1 2 Group numbers will display across the screen as you enter them Prg Single 0 99 Prg All Page 0 911 Long Range Systems 29 Freedom User Manual Prg System 0 0 Gro
44. this ID Span is required This function disables normal System ID functions except for Staff Paging and allows the programming of Guest Pagers from 1000 to 9999 To use ID Span 1 Press SETUP 2 Enter Password 3 Press 3 Other 4 Press 2 ID Span 5 Select F1 YES to enable or F4 NO to disable Alphanumeric Pager Button Enable Disable The buttons on an Alpha Pager can be enabled or disabled 1 Press SETUP and enter Password Press 1 for 1 System Press F2 DN until 1 POCSAG gt is displayed Press 1 for 1 POCSAG Press 2 for 2 Btns Enabled Press F1 Yes to enable Alpha Pager buttons or press F4 No to disable Alpha Pager buttons oa fF W M Alpha Pager Vibration Level The strength of vibration when an Alpha Pager receives a Vibration Alert can be varied 1 Press SETUP and enter Password Press 1 System Press F2 DN until screen show 1 POCSAG Press 1 POCSAG Press F2 DN until screen displays 1 Vibe Strength Press 1 Vibe Strength Press F1 UP to increase the level or F2 DN to lower the level Press F4 Done when finished oN OO P C NM Long Range Systems 18 Freedom User Manual Guest Message The Guest Message is the default canned message sent to Guest Alpha Pagers To change the message 1 Press SETUP and enter Password 2 Press 1 for 1 System 3 Press F2 DN until 1 POCSAG gt is displayed 4 Press 1 for 1 POCSAG gt 5 Press 3 for 3 Guest
45. umeric Vibration On of F2 No for Off Manager Pager Select 1 Vibe 1 time 2 Vibe 2 times 3 Vibe 3 times F2 ON 1 Vibe continuously 2 Vibe Beep 1 time 3 Vibe Beep 2 times F2 ON 1 Vibe Beep 3 times 2 Beep 3 times 3 Beep continuously Set to Page Staff or Guest Pagers In cases where the unit will always be paging staff pagers the transmitter default can be set to page either Guest or Staff pagers Factory default is Guest 1 Press SETUP and enter Password 2 Select 1 1 Default Mode 3 Select 1 Guest Paging for guest pager or 2 Staff Paging for staff pager Create Alphanumeric Messages If your staff pagers are alphanumeric they can display 77 different pre set messages numbered 000 through 076 and 22 additional user defined messages of up to 32 characters per message 077 through 099 1 Press SETUP and enter Password 2 Press 3 Other 3 Press 1 Canned Message 4 At the Canned Msg screen select F3 EDIT to edit message use F1 up or F2 DN to scroll through messages to edit 5 If no message exists at the Edit Message screen type a new message If a message exists press F3 EDIT to change it Enter the desired message using the number keys waiting until the cursor moves between letters i e for letter E press 2 twice Similar to a Cell Phone 6 Press the ENTER key to save your message Long Range Systems 16 Freedom User Manual Setting Time and Date for Freedom
46. up 1 1 Group 2 2 9 Return the Pager to the Charger when done If rechargeable 10 Repeat steps 2 through 8 for the remaining Pagers 11 When finished remove Pagers from the Charger and Page each one 12 Reprogram any Pagers that Do Not Page Alpha Encryption Only LRS Alpha pagers can be encrypted and be programmed from the transmitter Encryption does not change the pager numbering 1 Press Setup 2 Enter Access Code 3 Press the F2 DN until the display shows 2 Encryption 4 Press 2 2 Encryption 5 Select 1 ON SET 2 OFF 3 TRANSMIT KEY 1 1 On Set to enable encryption and set new encryption key Enter 16 double digits Note all ff will disable the key Example 11 12 13 44 11 11 11 11 11 11 11 11 11 11 11 11 Press ENTER when finished with each line Follow instructions on display Turn the pager off then on When it stops vibrating press ENTER note more than 1 pager can be encrypted at once Screen will display Transmitting Key Pager will beep once and display Pgr Encryption 128 bit 2 2 Off to disable encryption The display shows Transmit Key Now press the F1 YES key to send or F4 NO Follow instructions on display Turn the pager off then on When it stops vibrating press ENTER Screen will display Transmitting Key Pager will beep once and display Pgr Encryption None 3 3 Transmit Key to send the current encryption key to pagers
47. za Charger CH PZ Programming To program the pager see pg 27 Using Alphanumeric Coaster Guest Pagers aro Y aces PP a TT utes Charging Any Alphanumeric Coaster pager will require use of an LRS coaster charger 1 Place the pager in the charger 15 pagers at a time on a Charger 2 Allow unit to charge fully overnight 3 Remove from charger and pager will vibrate beep and light all lights as a verification that it is working 4 Replace the pager in the charger at the end of each day The Alphanumeric Coasters use the Charger 8 CH R8 Programming To program the pager see pg 27 Long Range Systems 40 Freedom User Manual Cleaning amp Charging Instructions For LAS Paging Equipment Cleaning LRS pagers are made from industrial strength polycarbonate material However this material is sus ceptible to hairline cracking if non approved cleaners are used When cleaning LRS pagers we recom mend only using ISOPROPYL ALCOHOL BASED CLEANERS To clean the equipment 1 Take a clean rag and an isopropyl alcohol based cleaner 2 Soak the clean rag with the isopropyl alcohol cleaner 3 Wipe down the pagers or equipment Cleaning equipment with any other non approved cleaners can weaken plastic and cause hairline cracks Pagers and equipment that are cleaned with unapproved cleaners and suffer cracking will not be covered under warranty Do not submerge any LRS paging equipment in any type of liquid as th

USER MANUAL - Pager2.net

Contents

Download Pdf Manuals

Related Search

Related Contents