OKIMAT 6
Contents
1. Q Never clean the drive in an automated washing system or with a high pressure cleaner Do not allow fluids to penetrate the drive Damage to the system could result 1 Always disconnect the mains power plug before you start to clean the drive Disconnect the batteries if you are using the battery operated reset function 2 Clean the OKIMAT 6 drive using a dry cloth 3 Be sure that you do not damage the drive s connecting cable amp Do not use a cleanser that contains benzene alcohol or similar solvents 35 Disposal 10 36 OKIMAT 6 Disposal The OKIMAT 6 drive consists of electronic components cables and metal and plastic parts You should observe all corresponding national and regional environmental regulations when disposing of the OKIMAT 6 drive The disposal of the end product is regulated in Germany by Elektro G internationally by the EU Directive 2002 95 EC RoHS from 1 Jul 2006 and Directive 201 1 65 EU RoHS from 3 Jan 2013 or by any applicable national laws and regulations The end product is not regulated by the EU Directive 2002 96 EC WEEE and its amendment EU Directive 2003 108 EC The OKIMAT 6 drive should not be disposed of with normal household waste er The disposal of the 9 V batteries is regulated in the EU by Battery Directive 2006 66 EC in Ger many by the BattG battery law of 25 6 2009 and internationally by any applicable national laws and regulations2. The 9 V batteries should not be disposed of with normal household waste pui 68018 b Declaration of incorporation According to Appendix II of the EU Machinery Directive 2006 42 EC The manufacturer DewertOkin GmbH WeststraBe 1 32278 Kirchlengern Germany declares that the incomplete machine described below OKIMAT 6 complies with the following basic requirements of the Machinery Directive 2006 42 EC Sections 1 1 3 1 3 3 1 3 4 1 3 7 1 5 1 1 5 2 1 5 5 1 5 6 1 5 7 1 5 8 1 5 9 1 5 10 1 5 13 1 6 3 You may only operate this machine after you have confirmed that the end product into which this drive will be installed complies with the Machinery Directive 2006 42 EC On request the manufacturer is obliged to send the special documentation accompanying the par tially completed machinery electronically to the appropriate national institution The special technical documents corresponding to the machine have been created according to Appendix VII part B The following person is responsible for the technical documentation Hartmut Klimm Address cited above Tel 05223 979150 ee Kirchlengern Germany on 15 December 2012 Sascha Koltzenburg Head of R amp D EU Declaration of Conformity In compliance with Appendix IV of the EU EMC Directive 2004 108 EC In compliance with Appendix III of the EU Low Voltage Directive 2006 95 EC In compliance with Appendix VI of the EU RoHS Directive 2011 65 EU The manufactu
3. Serial No A t IP20 Stroke b Intermittent operations 2 minutes 18 minutes Push force Calendar week year Serial number for your drive Use in dry rooms only Protection class II Protection category Stroke head foot Follow all special disposal instructions 68018 b OKIMAT 6 Possible combinations 3 68018 b Possible combinations The OKIMAT 6 double drive can be combined for use with other single or double drives The fol lowing basic combinations are possible e an OKIMAT 6 with a handset e an OKIMAT 6 as the main drive and a single drive used as a slave drive with a handset e an OKIMAT 6 as the main drive and two single drives used as slave drives with a handset Systems can be customized by combining drives with the handset and control units as needed The system components must be connected in a specific order DewertOkin has separate system instruction manuals containing all information and instructions needed for these systems gt Only a DewertOkin device should be used to control the drive since they have already been verified to work together 13 Description OKIMAT 6 4 4 1 14 Description The OKIMAT 6 drive is an electrically driven motor that is responsible for moving the end product in a linear direction The head and foot sections of a bed can be adjusted depending on the drive op tions The drive is controlled by means of a handset The different drive m
4. Sockets for the electrical connection gt The case variations of the motor s rear side depicted are only to be taken as examples Other case options for the rear of the motor are possible 68018 b 15 Description OKIMAT 6 16 Power supply connection to mains A Please follow these operating instructions carefully You could be injured by fire or electrical shock if you do not follow these assembly instructions Variant with attached power cord The appropriate power cable is included depending on the regional version USA continental Europe the UK or Australia A Only use the proper power cable that is permitted in your country Be sure to use the correct plug adapter as described in Figure 6 D Figure 6 Power plug adapter regional variants A Double drive OKIMAT 6 B Power plug German version C Power plug USA version D Power plug Australian version E Power plug United Kingdom version 68018 b OKIMAT 6 Description Variant with detachable power cord The appropriate pluggable power cord is included depending on the regional version USA conti nental Europe the UK or Australia A Only use the proper power cable that is permitted in your country Be sure to use the correct plug adapter as described in Figure 7 Ad Figure 7 Power plug adapter regional variants A Double drive OKIMAT 6 B Shield cover C Power plug German version D Power plu
5. the contacts if re quired Check the batteries and replace if necessary Connect the batteries 33 Maintenance 9 9 1 34 Maintenance OKIMAT 6 gt You should only use spare parts which have been manufactured or approved by DewertOkin Only these parts will guarantee a sufficient level of safety Maintenance Type of check Check the function and safety of the electrical sys tem Look over the plug in con nections and electrical ac cess points for signs of dam age Look over the cables for any signs of damage Periodic functional test of the end switches Explanation A qualified electrician should carry out this inspection Refer to the Electrical connection section in the Installation chapter Check that all electrical cables and connections are firmly seated and correctly positioned Check the connecting cables for pinching or shearing Also check the strain relief and kink protections mechanisms in particular after any mechanical load Move the drive to the end positions in order to test the end switches Time interval Periodic inspections can be carried out at intervals based on the risk as sessment which you conduct for your end product At least every six months At least every six months At least every six months 68018 b OKIMAT 6 Maintenance 9 2 68018 b Cleaning and care The OKIMAT 6 drive was designed so that it would be easy to clean
6. treni asina diea pieicoeibiviieei der ATA SEET AEAEE A AEEA AEE EA R88 20 6 1 Safety notices to observe during installation esee eeeeenne ener 20 6 2 Installation procedure 5 usa 21 T Notices for OperallOnh uuceisuie ici ca aan ARAM E Ga hun Auen 29 7 1 Genefal notlCes 5 u nn cede AE N a E EEA E A N EEE 29 7 2 Notice for operating with optional configuration uneesnannnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn anne 32 8 Troubleshooting iso ae 33 68018 b 5 Table of Contents OKIMAT 6 9 MAINT EM ANIGO SPeRARNIIRIERTENERRRERERERERERERERRRERERERERERERFREFEREHERRERREREREFERERERERERERERERERERERERERERERE 34 9 1 Maintenance Coase scenario SET EEA AA A satecssescuedteestnueresscuentees 34 9 2 Cleaning AN Care E 35 10 jr an em 36 Declaration of incorporation ueeeeseeeeeee eene inanan enne nn nnne nnnm neniu notani snnm nisse nnns asse nnn inse nnns 37 EU Declaration of Conformity 22uu442044000nnn0nnnnnannnnnnnnnannnnnannnnnannnnnnnnnannnnnannnnnnnnnnnnnnnannnnnnnnnnnnnnnannnnn nenn 38 6 68018 b OKIMAT 6 General 1 1 1 1 2 1 3 68018 b General Configurations The OKIMAT 6 double drive is run in several different configurations The Possible combinations Chapter includes information about the different device combinations available About these installation ins
7. DEWE M A Phoenix Mecano Company OKIMAT 6 Installation Instructions Translation of the original installation instructions OKIMAT 6 Foreword Foreword Revisions Version Date Changes 11 10 First edition a 07 12 Second edition b 12 12 RoHS Safety Instructions Toggle Disclaimer and exclusion of liability DewertOkin is not responsible for damage resulting from e failure to observe these instructions e changes made to this product which have not been approved by DewertOkin or e the use of replacement parts which have not been approved or manufactured by DewertOkin Address of manufacturer DewertOkin GmbH Weststra e 1 32278 Kirchlengern Germany Tel 49 0 5223 979 0 Fax 49 0 5223 75182 http www dewertokin de Info dewertokin de Creation of a complete operating instruction manual for the entire end product 68018 b These instructions are only intended to be used by the end product manufacturer They should not be given to the operator of the end product The factual information contained within may be used as a basis when creating the end product manual The warning and danger notices are best suited for use in the end product s manual However it is not sufficient to simply follow these notices You should also carry out an internal risk assessment for your end product This can then be used as the basis for the safety notices in your manual These installation instructions do not c
8. ER indicates a hazardous situation which if not avoided will result in serious injury or death WARNING indicates a hazardous situation which if not avoided could result in serious injury or death moderate injury NOTICE is used to address practices which are not related to personal injury but may A CAUTION indicates a hazardous situation which if not avoided could result in minor or result in damage to the product or surroundings 68018 b OKIMAT 6 Safety Notices 2 2 1 68018 b Safety Notices Proper and intended usage The OKIMAT 6 drive is meant to be installed in beds e It provides motor adjustment capabilities for movable reclining bed parts It should be used in conjunction with suitable fittings and mechanics e tcan be used in the household HOME A This drive should only be used for the applications described above Any other applica tion is not permitted and can lead to accidents or damage to the unit Such non approved applications will lead immediately to the expiration of all guarantee and war ranty claims on the part of the end product manufacturer against the manufacturer Improper usage Be sure to follow the notices below concerning improper usage You should include them in your product manual in order to inform the users of your end product The OKIMAT 6 drive should not be used e with a medical product or installed in a medical product e in a
9. N HUERV T GREEN DE 5 1 eTa Al Sm 7 1 1 Configurations 23 ER El 7 1 2 About these installation instructions 11ceseeeceeeee eene nnn nnam nara mn anna nu aa na maa uana naa 7 1 3 Availability of this document eese esses esee eene entnehmen nennt r anne nnn nnmnnn eran nennen nnn 7 1 4 Gonventions Used e en ee nn ee aaa nen ann oma Dis PER den un ates dass cnr nn aas NT E P CRUCES 8 2 Salely NOLICES ausa carni anna Aa IB En tans Rene envied 9 2 1 Proper and intended usage uusssasssnannnnnnnnnnnnnanannnnnnnnnnnnnanannnnnnnnnnnnnannnnnnnnnnnnnnannnnnnnnnnnnnnnannnnnnen 9 2 2 Safety notices within the installation instruction and the operating instructions for the entire UE Ce LL DARREN I EI 10 2 3 Selection and qualification of personnel ununnusssnnnnnansnnnnnnnannnnnannnnnnnnnnnnnnnannnnnannnnnnnnnnnnnnnannnnnann 10 2 4 Notice on safety during operations eese nennen nennen nennen nennt nannten nns 11 2 5 Product identification enr ccca cc censa eu cca at coeadgu a irelluune 12 3 Possible combinations cesses eene enn nan nun nun nun nun nnnn nun nnn En 13 Description si ticcanceacecancuacecandvacaad dudnacendvanadai dudnadendvanedaidvdacdendvdaadai Grdaadei vanadiadvantdens 14 4 1 COMPONENIS 4 20 00 P 14 B Technical Specifications na aaa 18 6 InstallatiO I n eric roi
10. The mains cut off is not a central command device in the sense used by the DIN VDE 68018 b OKIMAT 6 8 Troubleshooting Troubleshooting This chapter describes troubleshooting methods for fixing problems If you experience an error that is not listed in this table please contact your supplier Only qualified specialists who have received electrician training should carry out trou bleshooting and repairs Problem The handset or drive system is not function ing The drive is suddenly not capable of move ment The battery operated reset is not functioning 68018 b Possible cause There is no mains supply voltage The hand switch or drive system is defective Possibly the thermal circuit breaker on the transformer has been triggered or is defective The thermal fuse on the trans former may have been triggered or may be defective The unit s fuse may have been triggered or may be broken There is no mains supply voltage A lead in connection has been interrupted mains power hand switch or auxiliary drive The batteries are empty Battery is not connected Remedy Connect the mains power Please contact your supplier or sales agent The drive system should be al lowed to pause for 20 to 30 min utes Please contact your supplier or sales agent Please contact your supplier or sales agent Connect the mains power Check the lead in connections and re seat
11. ation Chapter e Basic safety rules during operation refer to the Notices for Operation Chapter e The creation of a manual for the end product which contains these and other safety rules Creating a user s manual The manufacturer of the end product must create a manual for the users of that product The safety notices in the end product manual must be written based on the end product s risk assessment 68018 b 11 Safety Notices 2 5 2 5 1 12 Product identification Ratings plate type label OKIMAT 6 A ratings plate on each drive specifies the exact name and serial number of the drive It also states the technical specifications valid for that particular drive In particular you will find the maximum pull force and the maximum push force here The following illustration shows where the specifica tions are located on the drive s ratings plate gt The ratings plate shown is an example the specifications for your drive may differ from this illus tration OKIMAT 6 XXXXX A 230V 50 60Hz 50W o Intermittent Operation 2min 18min max Force 2x4000N Prod Date 40 10 X Serial No D123456 0001 DANAI Head 87 IP20 stroke p o OKIN Indoor use only A Phoenix Mecano Company Figure 2 Ratings plate example OKIMAT 6 Model name XXXXX Article number 230V 50 60Hz Input voltage and frequency 50W Power level Intermittent Operation 2min 18min max force Prod Date
12. fied in the Machinery Directive 2006 42 EG and e when the manufacturer expressly declares the compliance of the end product The manufacturer of the end product must create a manual for the users of that product The safety notices in the end product manual must be written based on the end product s risk assessment Selection and qualification of personnel This drive should only be installed into the end product by someone who has completed training in electronic motor assembly or has equivalent qualifications You should only install this drive when you are qualified to do so Otherwise a properly qualified person should be found for this task 68018 b OKIMAT 6 Safety Notices 2 4 Notice on safety during operations Basic safety rules must be followed in order to ensure that the end product can be continually op erated in a safe manner These rules must be observed while using the end product and while in stalling the drive These rules and safety measures can be categorized as follows e Construction measures before the installation refer to the Ensuring operational reliability dur ing installation section in chapter Installation e Safety fundamentals during the drive installation and during cable and wire routing refer to the Safety notices to observe during installation section in the Installation Chapter e Using the drive in intermittent duty refer to the General notices section in the Notices for Op er
13. g USA version E Power plug Australian version F Power plug United Kingdom version 68018 b 17 Technical Specifications 5 18 OKIMAT 6 Technical Specifications Connection to mains power AC or Input voltage DC Current consumption under rated load Power output Fuse Permitted push force Mode of operation under max rated load Protection classification Noise level Drive type Protection category Stroke Colours Length x width x height Axle gap distance Weight 100 V 240 V AC 50 60 Hz refer to the ratings plate on the drive 24 V DC refer to the ratings plate on the drive Max 8 0 ADC 50 W T 0 63 T 3 15 A depending on mains power connec tion refer to the drive s ratings plate Max 8000 N total on both sides Intermittent duty 2 min 18 min II lt 65 dB A Double drive IP20 87 69 standard 53 74 Refer to sales brochure 715 mm x 177 mm x 130 mm 581 mm Approx 5 kg Option battery operated reset function Voltage Ambient conditions for operation storage and transport Transport storage temperature Operating temperature Relative humidity Air pressure Altitude One or two 9 V batteries type 6LR61 depending on version From 20 C to 50 C From 4 F to 122 F From 10 C to 40 C From 50 F to 104 F From 30 to 75 From 800 hPa to 1060 hPa lt 2000 m Mode of operation intermittent duty 2 min 18 min Thi
14. ld be found for this task 23 Installation OKIMAT 6 24 Variant with detachable power cord The appropriate pluggable power cord is included depending on the regional version USA conti nental Europe the UK or Australia The power socket is located behind the shield cover on the OKIMAT 6 drive Be sure to use the correct pluggable power adapter as described in Figure 10 A Please follow these operating instructions carefully You could be injured by fire or electrical shock if you do not follow these assembly instructions Figure 10 Power plug adapters regional variants A Power socket B Power plug C Shield cover 68018 b OKIMAT 6 Installation 68018 b The pluggable power cord should be attached to the power socket A located on the front of the OKIMAT 6 drive A Only use the proper power cable that is permitted in your country Be sure to use the correct plug adapter as described in Figure 7 A You should only connect and disconnect the cables when they are completely discon nected from any live current Unscrew the screws on the shield cover C Pull the shield cover C away from the socket Plug the power plug from the power cord B into the socket A Put the shield cover C back on Tighten the screws back on the cover Follow the notice below when plugging the power plug into the power outlet kr O N Q There is a delay after the supply voltage is app
15. lied before the device actually turns on Wait at least 15 seconds before commissioning 25 Installation OKIMAT 6 26 Option battery operated reset function Connecting the 9 V batteries Figure11 Connecting the 9 V batteries A Battery compartment B Battery clip attached C 9 V battery type 6LR61 D Battery clip unattached Connect the nine volt batteries first when you would like to perform a battery operated reset The batteries may only be used to power the reset function one time Take out the batteries and dispose of them properly after the reset function has been carried out 68018 b OKIMAT 6 68018 b Installation Routing the electrical cables When routing the cables be sure that e the cables cannot get jammed e no mechanical load such as pulling pushing or bending will be put on the cables and e the cables cannot be damaged in any way Fasten all cables especially the mains cable to the end product using sufficient strain relief and kink prevention methods Be sure that the design of the end product prevents the mains cable from coming into contact with the floor during transport 27 Installation OKIMAT 6 6 2 3 28 Dismantling A Work on electrical components should be conducted only when the mains power con nection is unplugged gt Certain details may change as a result of technical changes 1 Move your product into a position where it is sup
16. n your product refer to the symbols on the OKIMAT 6 as de scribed in Figure 3 Push the drive in so that the brackets D fit into the slots B 5 Close the shutters A on the drive by snapping them back in The OKIMAT 6 is now securely attached to the end product 6 Disconnect all additional components such as slave drives or handset from their sockets 7 Connect the mains power plug Follow the notice below when plugging the power plug into the power outlet Q There is a delay after the supply voltage is applied before the device actually turns on Wait at least 15 seconds before commissioning 68018 b OKIMAT 6 Installation 6 2 2 68018 b Electrical connection A Electrical components should be connected or disconnected only when the power sup ply cord is unplugged Q There is a delay after the supply voltage is applied before the device actually turns on Wait at least 15 seconds before commissioning Variant with attached power cord Only personnel with the following training are qualified to work on the attached power cord or to replace the power cord e someone who has completed training in electronic motor assembly or e someone with equivalent qualifications or e someone who has successfully completed the appropriate DewertOkin training pro gram You should only work on the attached power cord when you are qualified to do so Otherwise a properly qualified person shou
17. ng your end product you should take the drive adjustment movement into account with passive safety mechanisms and with the appropriate safety notices in your operating instructions e Installation methods for ensuring passive safety Install the OKIMAT 6 drive so that none of the positions where shear and pinch hazards exist are accessible exter nally When preparing safety notices for the operator be sure that your operating instructions inform the user of these points 68018 b OKIMAT 6 Installation 6 2 Installation procedure 6 2 1 An example installation Before installing the drive make sure that you are observing all of the safety notices found in the Safety notices to observe during installation section C Figure 9 Installing the double drive A Shutters B Fitting mounts C End product bed D Brackets 68018 b 21 Installation OKIMAT 6 22 1 Move your product into a position where it is supporting no load A Be sure to carry out work on the drive in a position so that no loads are bearing on it Only in this way can you be sure to avoid any risks of crushing or injury Disconnect the batteries if you are using the battery operated reset function Pull strongly on the shutters to the side A The slots B for the brackets D are uncovered Align the OKIMAT 6 next to your product The slots for the head and foot sides must be properly aligned with the correct brackets o
18. ny environment where combustible or explosive gases or vapours e g anaes A thesiology may be present e ina moist environment e Outdoors e in any application that will be cleaned with an automated washing system e for raising and lowering loads in industrial applications The OKIMAT 6 drive may not be operated A e by small children e by frail or infirmed persons without supervision or e inthe proximity of small children A You should only use spare parts which have been manufactured or approved by DewertOkin Only these parts will guarantee a sufficient level of safety Safety Notices OKIMAT 6 2 2 2 3 10 Option battery operated reset function The battery operated reset function is not a safety system and does not avert danger DewertOkin does not guarantee that the drive will function in the event of a power outage If the end product manufacturer chooses to guarantee the functionality of the end product during a power outage then the end product manufacturer is responsible for arranging a mechanism to en sure this functionality Safety notices within the installation instruction and the operating instruc tions for the entire machine The manufacturer of the end product is only permitted to operate the OKIMAT 6 drive by itself an incomplete machine e when the end product for which the OKIMAT 6 drive is intended is in compliance with all pro tective measures speci
19. odels vary according to the e motor power e number of motors e also in the variations attached power cord and detachable power cord e model with optional reset function gt We reserve the right to make unannounced technical changes in the course of our continual product improvement process gt The Possible combinations Chapter describes the different possible combinations of drives and handsets hand held remote controls You can also ask your supplier or dealer for additional information Components The main components of the OKIMAT 6 drive are the motor and the adjustment motion mecha nism This mechanism is housed under the shutters The shutters must be opened in order to mount the drive to the end product The brackets fastened to the end product are then inserted into these openings Figure 3 Main components of the OKIMAT 6 double drive variant with attached power cord A Shutters B Strain relief C Battery compartment with 9 V batteries D Symbol for head end of bed E with attached power cord F Symbol for foot end of bed 68018 b OKIMAT 6 Description Figure 4 Main components of the OKIMAT 6 double drive variant with detachable power cord A Shutters B Strain relief C Shield cover for detachable power cord D Symbol for head end of bed E Batteries in battery compartment F Symbol for foot end of bed A A Figure 5 Case options for the OKIMAT 6 double drive Examples A
20. ontain all information required to safely operate the end product They only describe the installation and operation of the drive as partially completed ma chinery The instructions are intended for the technicians responsible for manufacturing an end product and not for the operators of the end product Foreword OKIMAT 6 Notice for customers in EU nations German Inspection Authority T V testing label The construction of the OKIMAT 6 has been inspected by the German Inspection Authority TUV The TUV also monitors the production of the OKIMAT 6 The official German TUV label certifies this construction inspection and production monitoring Production monitored Type Tested Figure 1 The TUV label 4 68018 b OKIMAT 6 Table of Contents Table of Contents FO FEW ONG SES HA NER C CR EK KT CREE 3 REVISIONS soi sched cies deed os 00 foe seceded 3 Disclaimer and exclusion of liability uneeensennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannenn namen nn anne 3 Address of manufactfer 5 eei nen Denen n a Do aa an ca anna a Fa Dann CER MR UE EUN nn en ee oaa IESE EUSE gen 3 Creation of a complete operating instruction manual for the entire end product 3 Notice for customers in EU nations aiii ee an nn nnna nanna 4 Table Of CODIGDIES iu cn ccv A anna UNS FM ER UM EVER Ku FERME a EN EE RNC FE
21. porting no load A Be sure to carry out work on the drive in a position so that no loads are bearing on it Only in this way can you be sure to avoid any risks of crushing or injury 2 Pull out the mains power plug Disconnect the batteries if you are using the battery operated reset function 3 Disconnect all additional components such as slave drives or handset from their sockets Q Be sure to support the drive s weight to prevent it falling 4 Pull strongly on the shutters to the side A 5 Pull out the OKIMAT 6 far enough so that the brackets D are out of the slots B The OKIMAT 6 is now unattached and can be removed 6 Push the shutters A back onto the OKIMAT 6 so that they are not lost during transportation 68018 b OKIMAT 6 Notices for Operation 7 Notices for Operation The factual information contained within may be used when you are creating the end product man ual The installation instructions do not contain all information required for the safe operation of the end product They only describe the installation and operation of the drive as a partially assembled piece of machinery A When creating the operating instructions remember that the installation instructions are intended for qualified specialists and are not for typical users of the end product 7 1 General notices gt Only a DewertOkin device should be used to control the drive since they have already been ve
22. rer DewertOkin Antriebs und Systemtechnik GmbH Weststra e 1 32278 Kirchlengern Germany declares that the following product OKIMAT 6 meets the requirements of the following EU directives Electromagnetic Compatibility Directive 2004 108 EC Low Voltage Directive 2006 95 EC RoHS Directive 2011 65 EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment Applied standards EN 60335 1 2012 EN 55014 1 A1 2009 EN 55014 2 A2 2008 EN 61000 3 2 A2 2009 EN 61000 3 3 2008 This declaration of conformity is no longer valid if constructional changes are made which signifi cantly change the control unit i e which influence the technical specifications found in the instruc tions or the intended use Kirchlengern Germany on 15 December 2012 Sascha Koltzenburg Head of R amp D DewertOkin GmbH Weststra e 1 32278 Kirchlengern Germany Tel 49 0 5223 979 0 Fax 49 0 5223 75182 http www dewertokin de Info dewertokin de 44 DEWERT OKIN A Phoenix Mecano Company ID No 68018
23. reset function is not a safety system and does not avert danger A Connect the nine volt batteries first when you would like to perform a battery operated reset The batteries may only be used to power the reset function one time Take out the batteries and dispose of them properly after the reset function has been carried out gt If the end product is under a heavy load which prevents the reset function from operating the strain or load on the end product must first be removed before a reset can be carried out Option The mains cut off mechanism The mains cut off feature is only available with the attached power cord variants The mains cut off mechanism is responsible for isolating the drive automatically from the mains power supply when the drive is not moving A switching component is used to isolate both poles of the power trans former from the mains power supply The mains cut off mechanism allows power to the drive only after a button has been pressed on the handset to trigger drive motion gt Do not use the integrated mains cut off if you already use an in house mains cut off system regulations You should first completely disconnect the voltage supply from the drive system before conducting any type of work on a DewertOkin product which features a mains cut off First pull out the power plug This guarantees that the system is safely shut off in compliance with the German DIN VDE 0105 and BGV A3 regulations
24. rified to work together Delayed start up Follow the notice below when plugging the power plug into the power outlet Q There is a delay after the supply voltage is applied before the device actually turns on Wait at least 15 seconds before commissioning Power on time intermittent operations The OKIMAT 6 drive has been designed for intermittent operations Intermittent operation is an op erational mode where the drive must pause after a specified maximum period of operation power on time This protects the drive from overheating In an extreme case overheating can lead to a malfunction gt The ratings plate on the drive specifies the maximum power on time and the required pause in tervals Avoiding toggle operations You should avoid switching from one direction of travel to the opposite direction without first stop ping the motor Make sure that you pause between motions A pause motor stop time can be activated using the operating element or handset D You should always avoid a quick change toggle of directions 68018 b 29 Notices for Operation OKIMAT 6 Avoiding electrical risks A Be sure that all live current carrying parts of the drive system and power supply can not be touched In particular be sure that unused power and controller connections are covered adequately Shutting off the drive A Pull out the power plug in order to shut off the drive The power plug mu
25. s means that after the unit is operated with its rated load for up to two minutes it must then be paused for 18 minutes The unit can malfunction if this pause is not observed Other stroke distances are available on request 68018 b OKIMAT 6 Technical Specifications 130 715 Figure 8 Dimensions of OKIMAT 6 drive in mm 68018 b 19 Installation OKIMAT 6 6 6 1 6 1 1 20 Installation Safety notices to observe during installation Basic safety rules must be followed in order to ensure that the end product can be continually op erated in a safe manner These rules must be observed while using the end product and while in stalling the drive Ensuring operational reliability during installation The safety and reliability of the end product containing the DewertOkin drive can be ensured by us ing the proper construction methods described below Avoiding fatigue fractures Drives that are incorrectly installed can undergo fatigue fractures which then create a risk of injury A e Install the drive in the end product so that it is properly aligned This will help pre vent shear stress e Do not position the drive at a slanted angle when installing it in the end product A slanted angle between the intended direction of movement of the end product and the drive s direction will create shear stress and could lead to a fatigue fracture Avoiding a pinching hazard When designi
26. st always be accessible during operations so that emergency shut off is possible Avoiding cable damage Be sure that your operating instructions inform the user about the possible cable risks A The cables particularly the mains cable should not be run over In order to prevent injuries or drive damage no mechanical strain should be placed on the cables 30 68018 b OKIMAT 6 Notices for Operation Looping the handset cable through the strain relief mechanism Figure 12 Looping the cable through the strain relief mechanism A Handset cable loop B Looped in cable C Secured cable 1 Connect the plug from the handset to the handset socket on the OKIMAT 6 2 Loop the handset cable through the strain relief catch and pull back gently on the loop as illus trated in Figure 12 68018 b 31 Notices for Operation OKIMAT 6 7 2 7 2 1 7 2 2 32 Notice for operating with optional configuration Option battery operated reset function The battery operated reset function allows the drive system to be operated during a power outage One or two 9 V batteries can be used to power the OKIMAT 8 in the event of a power outage The batteries should only be connected when a power cut occurs The batteries are not connected by default since they have limited capacity They can only be used to power the reset function once The used batteries should then be replaced and properly disposed of The battery operated
27. tructions These installation instructions must be followed closely in order to install this drive successfully and safely in the end product These instructions are not an operating manual for the end product These instructions will help you to minimize danger repair costs and down times They will also help you to maximize the reliability and lifespan of the end product The notices in these instructions must be followed Following the guidelines during A installation and connection procedures will help to minimize e the risk of accident and injury and e damage to the drive system or the end product These installation instructions have been written with due care and attention However unless oth erwise required by law we do not guarantee that the data images and drawings are accurate or complete nor do we accept liability for their contents gt We reserve the right to make unannounced technical changes in the course of our continual product improvement process Availability of this document As manufacturer of the end product you are obligated to comply with Machinery Directive 2006 42 EC This directive stipulates that the installation instructions must be kept on file for gov ernmental inspection purposes General 1 4 OKIMAT 6 Conventions used Notices which do not relate to safety are indicated in these instructions with a triangle gt Triangular notice symbol Safety notice explanations DANG
Download Pdf Manuals
Related Search