Home

TM_Clean premises and equipment_280115

1. Safety guidelines When cleaning the following must be observed Never put hands inside rubbish containers there is always the possibility of broken glass syringes and other objects which can cause cuts pricks and other injury e Always empty the container by holding it upside down into a waste garbage bag do not scoop out the rubbish and move it by hand into the waste garbage bag Never put hands down the back of chairs or sofas once again there is the potential for cuts and needle stick injuries Always use wear the designated personal protective clothing and or equipment for the job when undertaking certain jobs and the use of these is not optional where these have been identified as being necessary they are mandatory Use only designated devices steps ladders scissor lifts for reaching high locations it is never acceptable to use tables or chairs to stand on to reach these places Push the cart trolley from area to area to see possible risks obstructions Never over load the trolley go back to the storeroom for re supply as necessary rather than weigh it down and or load it to the extent it is too heavy and or unstable Never over load the cleaning caddy when carrying it as this can cause musculo skeletal damage injury Never use linen items or uniforms for cleaning and or drying fixtures and fittings only use designated cloths for each individual purpose as identified by the business
2. ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Element 4 Apply pressure washing techniques 4 1 Assess area to be pressure washed Introduction Before pressure washing any area it is standard procedure to first assess the job This section describes considerations in this regard Assessing the area to be cleaned Activities involved in assessing areas to be pressure washed are similar but slightly different to those required when assessing areas to be wet or dry cleaned Most locations where pressure washing is suitable for use will be external locations but some internal areas such as kitchens toilets are also pressure cleaned by some operators There may be a need to e Identify areas to be pressure washed through Written printed work order work allocation or scheduled cleaning list Talking to supervisor and being directed by them Being contacted by personnel responsible for or working in the area and being notified of a cleaning need e Confirming suitability for cleaning the area using pressure washing techniques other people who do not have experience competency with pressure washing can believe pressure washing is needed when it is a totally inappropriate ineffective dangerous and or potentially damaging technique e Rely on personal expertise to determine if an area job is genuinely a pressure washing job e Identify soil type
3. Please tick the appropriate box Agree Don t Do Not Does Not Know Agree Apply There was too much in this competency to cover without rushing Most of the competency seemed relevant to me The competency was at the right level for me got enough help from my trainer The amount of activities was sufficient The competency allowed me to use my own initiative My training was well organised My trainer had time to answer my questions understood how was going to be assessed My trainer feedback was useful Enough equipment was available and it worked well The activities were too hard for me was given enough time to practice ASEAN 2015 Trainee Manual Clean premises and equipment Trainee evaluation sheet evaluation sheet The best things about this unit were The worst things about this unit were The things you should change in this unit are ASEAN 2015 Trainee Manual Clean premises and equipment Trainee self assessment checklist Trainee self assessment checklist As an indicator to your Trainer Assessor of your readiness for assessment in this unit please complete the following and hand to your Trainer Assessor Clean premises and equipment Element 1 Prepare to clean 1 siettesmimenimenininent 2 soanen 4 sameo 4 econ sity oeaupren pat asteen eit D Element 2 Apply wet area cleaning techniques aaan E A e a A E D E A faa mn S a 25 ean smaras s
4. This section discusses general pre requisites for operating a pressure washer presents practical pressure washing operational advice and identifies ancillary work commonly required as part of an overall pressure washing task especially when cleaning vehicles Important requirements prior to operating a pressure washer Using pressure washers effectively and efficiently is a skill demanding three key pre requisites e Initial training including Theory which should cover How the unit works Names of parts Details of what it can be used on and what it must not be used on Attachments and their use especially nozzles Safety which must emphasise never pointing the gun at anyone or animals and never using any machine with broken defective parts Practical aspects which must cover demonstrations of Moving the unit never use the hose to pull the machine only move the equipment using the handle Connecting up the unit to water and chemicals for example detergents and disinfectant Connecting attachments always double check to ensure connections are properly made Activating the unit turning it on and off Cleaning using the unit to clean a variety of surfaces e Practice supervised overseen by an experienced operator when first operating using the unit in order to Prevent injury Prevent damage Confirm operational techni
5. Cleaning involves e Tipping out the dirty water into the sink gully trap identified for this purpose buckets should not be emptied in public areas e Removing or rinsing out any dirt material e Washing with designated detergent some businesses will also require sanitising e Checking wringers and rollers of mop buckets and removing debris as required clean rollers with cloth e Turning upside down and leaving to air dry Wet vacuum cleaners All vacuum cleaners must be cleaned in accordance with manufacturer s instructions generic requirements include e Clean out at the end of each shift e Drain and dry e Dry filters and baskets e Wipe clean attachments e Wrap stow power cord and hose correctly and safely ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques Carpet shampoo machines Requirements include e Clean after each use e Wipe clean e Empty drain and flush unit and hose e Clean head e Dry e Stow cord and hose All cleaning of carpet shampoo machines must be done in accordance with manufacturer s instructions Cleaning PPE Cleaning personal protective equipment and clothing should entail e Following manufacturer s instructions for each item in every instance e Discarding items no longer suitable for use e Reporting and or replacing worn or damaged items or articles e Wiping down with detergent and sanitiser as appropriat
6. Never use bathroom washroom items bath towels face towels face washers bath mats for cleaning washing or drying floors walls fixtures and fittings Keep dirty soiled or used items separate from clean unused items it is never acceptable to mix the two together and it is never acceptable to stack clean items on top of dirty ones or stow store them together Ensure clean hands when handling clean linen it is important to make sure clean items from the laundry are not made to look dirty as a result of being handled by unclean hands to avoid this problem use disposable gloves and wash hands regularly Use colour coded cloths in accordance with house rules to assist in preventing the spread of germs bacteria when undertaking nominated cleaning tasks e For example only red cloths can be used for the toilet and or bidet or toilet closet area only green cloths can be used in the kitchenette food area yellow cloths for other public areas Follow proper procedures for disposing of hazardous items these will be guidelines checklists for dealing with for example needles blood stained items and other specified items Possible action can include Placing all items contaminated with body waste fluids into a red coloured bio hazard bag as opposed to placing these items into the normal garbage bag ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning
7. there is a need to determine where if possible the type of dirt needing to be cleaned removed e This is important because it may influence the chemicals used to complete the work e Soil type may be identified by Use of the senses looking at it smelling it and or feeling it rubbing it between the fingers Talking to anyone who may have caused the problem to ask what happened and what the soil is ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques Identify vehicle s to be pressure washed where the task requires vehicle cleaning it is necessary to determine Type of vehicle bus coach four wheel drive sedan this affects time required and may impact degree and type of dirt Specific identifier for the vehicle such as registration number or organisational numbering code to ensure the correct vehicle is cleaned Identify surface type to be cleaned common surfaces suitable for pressure washer cleaning are Brick structures and brick finished walls and floor surfaces Car parks made from asphalt or concrete Concrete floors such as those in storage areas Entertainment seating in outdoor arenas areas External walls and roofs made from hard materials Gutters and fascia boards Awnings and facades Painted surfaces Steps and stairwells Confirming condition of equipment in
8. Be alert to unusual noises vibrations and smells that can indicate an operational problem with the machine e If there is a fault with the machine Stop work immediately Return the machine to the store or Maintenance area make sure it is tagged as Unsafe Do not use Obtain a safe fully operational machine and resume work ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques e ake time to do the job properly this can mean Making sure all areas are vacuumed not just the areas that look dirty Cleaning into the corners of rooms e Cleaning behind doors this often means opening closing the door and vacuuming the floor carpet when the door is both open and closed e Moving small pieces of equipment furniture and vacuuming under them as opposed to just vacuuming around them e Only use machines classified as wet vacuum cleaners for cleaning wet floors Stains When vacuuming e Pay attention to the need to identify stains e Remove stains as soon as possible using appropriate stain removal method s relating specifically to the type of carpet active ingredients of the chemical and the type of stain e Report stains which cannot be removed due to difficulty or time factors Areas to use the vacuum cleaner on not just floors The vacuum cleaner can be used to e Clean upholstered furniture e Remove cobwebs e Clean the ceiling and ceiling
9. Depending on what is in each room there may be a requirement to have Polishes such as furniture polish Detergents a wide range is available such as Glass cleaner for use with glass surfaces windows and mirrors Multi purpose all purpose general purpose cleaners suitable for use on a wide range of surfaces including plastics glass walls and floors Metal cleaners for cleaning metals such as stainless steel brass and aluminium Metal specific polishes cleaners may be required for hand rails fixtures and fittings Leather cleaners many manufacturer s of leather items will insist only nominated leather cleaning chemicals or systems they provide are used for cleaning their products Failure to use their items may jeopardise warranties for lounge suites chairs and similar ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Shampoos and purpose built cleaners for certain fabrics Porcelain and ceramic cleaners for cleaning tiles Toilet and urinal cleaners Sanitisers Disinfectants Deodorisers and air sprays Pest control sprays and similar Usage Charts Suppliers of cleaning products chemicals and agents will provide advice and information about how to use their products Commonly suppliers provide Usage Charts for their chemicals which will identify the chemicals they provide and descr
10. which were done and may require e idying the area Removing drop sheets and protective cloths materials Arranging re arranging the furniture Placing items in designated assigned areas Returning excess items to other storage areas or to their correct location Removing warning signs cones and other barriers or tapes Removing cleaning equipment carts materials and cleaning chemicals Performing final touch ups e Finalising the job such as placement of products re stocking of essential requisites spraying room freshener deodorant e Inspecting the area e Returning the area to operational status e Disposing of soil and waste e Returning vehicles to designated locations e Recording completion of cleaning e Dealing with lost and found items ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques 3 5 Clean check and store equipment and chemicals Introduction Following completion of cleaning tasks the standard need to clean check and store equipment and chemicals remains Generally speaking less cleaning of equipment and fewer checks are required following dry cleaning This section highlights previously presented information in this regard Cleaning the equipment used Cleaning locations Cleaning of items may be undertaken e Inthe cleaning store room e In a designated cleaning room e n nominated outside locations Need
11. Clean check and store equipment and 4 1 20 chemicals Element 5 Apply ceilings surfaces and fittings cleaning techniques 5 1 Assess ceilings surfaces and fittings to be 5 z 2 10 11 20 cleaned Select appropriate equipment and chemicals 5 1 5 2 5 3 Clean ceilings surfaces and fittings 5 T 7 2 5 5 Tidy worksite 5 1 5 2 14 24 5 3 5 6 Clean check and store equipment and Di lsc One 20 25 chemicals 5 3 ASEAN 2015 Trainee Manual Clean premises and equipment a Glossary Term Explanation Bio waste Human waste Low speed multi purpose machine which can be used for stripping scrubbing and low speed buffing High speed floor polisher for providing high gloss finishes to vinyl floors Cleanina schedule List identifying when nominated items areas must be g cleaned Consumables Items which are consumed used as part of a process and will need to be replenished Elbow grease Effort hard work Material Safety Data Sheet Personal Protective Equipment and Clothing Level of acidity or alkalinity 7 is neutral 7 14 is alkaline below 7 is acidic Residual Current Device Standard Operating Procedure Work Instruction E Removing wax and dirt from floor in preparation to re Stripping a floor sealing it ASEAN 2015 Trainee Manual Clean premises and equipment ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean Element 1 Prepare to
12. a ia iaa aaa adia aia a iaaa diaii paati 5 AOSS TY e E E E ee E E E E E 7 Element 1 Prepare to ClOANN ccccccecccscccecccecccscccecccucecacecaeecaeecaeecsuecaescuescaeeceeseaseneeseasenass 9 Element 2 Apply wet area cleaning techniques cccccecsecssssesseseeseeseuseseeeeseeseusensensees 27 Element 3 Apply dry area cleaning teChniques cccccccceceeeeeeeeeeeseeeseeeeseeeeeeeeseeeeseeeeaes 51 Element 4 Apply pressure washing techniques cccccccceeeceeceeeeeeeeeeseeeeseeeeseeeseeeeseeeeaes 67 Element 5 Apply ceilings surfaces and fittings cleaning techniques cccccseeeeeeeeees 83 Presentation of written WOM vecvicoe sce tecnrecvicetsnaetucmndvdeetancetesumad instance a a aaa aa a aia Eaa 103 Recommended Lai cc0cccceeeccececececeecceueeceeeccueeceucessueceueecueesueessueeseeessueesseesseeeseneens 105 Trainee evaluation SNC CU vise cine csatviandiandiannsatviandiandionnaiviantiaadionmaiviartiandionattiartiandionantianns 107 Trainee self assessment CNCCKIIS i tininintnaensancianrantoaennancianranoaensantianantoansantianmantodnsantons 109 ASEAN 2015 Trainee Manual Clean premises and equipment ASEAN 2015 Trainee Manual Clean premises and equipment Introduction to trainee manual introduction to trainee manual To the Trainee Congratulations on joining this course This Trainee Manual is one part of a toolbox which is a resource provided to trainees trainers
13. all the necessary equipment facilities and drainage Removal of all dirt and mud from the underneath of vehicles ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Online videos See the following for extra information http www youtube com watch v kRQ3QilQtJA Pressure Washing Basics 2 mins 38 secs http www youtube com watch v LIlk078BqdUM How to use a pressure washer 6 mins 21 secs http www youtube com watch v wNsR8KWL_08 Power washing a drive way 2 mins 41 secs http www youtube com watch v zV5mHIhZdYw Pressure cleaning by King of Pressure 1 min 13 secs http Awww youtube com watch v Fz297b Tb RRM How to use and maintain a pressure washer 3 mins 6 secs ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques 4 4 Tidy worksite Introduction In the same way the worksite needs to be returned to service after performing wet and dry cleaning so too is there a need to do so after pressure washing This section identifies the requirements for this Finishing activities The exact nature of finishing activities required will depend on the preparation activities which were done An important difference in returning a worksite back to service that has been pressure washed is the common need for the area to be dry Specific actions may include
14. and assessors to help you become competent in various areas of your work The toolbox consists of three elements e A Trainee Manual for you to read and study at home or in class e A Trainer Guide with Power Point slides to help your Trainer explain the content of the training material and provide class activities to help with practice e An Assessment Manual which provides your Assessor with oral and written questions and other assessment tasks to establish whether or not you have achieved competency The first thing you may notice is that this training program and the information you find in the Trainee Manual seems different to the textbooks you have used previously This is because the method of instruction and examination is different The method used is called Competency based training CBT and Competency based assessment CBA CBT and CBA is the training and assessment system chosen by ASEAN Association of South East Asian Nations to train people to work in the tourism and hospitality industry throughout all the ASEAN member states What is the CBT and CBA system and why has it been adopted by ASEAN CBT is a way of training that concentrates on what a worker can do or is required to do at work The aim is of the training is to enable trainees to perform tasks and duties at a standard expected by employers CBT seeks to develop the skills knowledge and attitudes or recognise the ones the trainee already possesses to achiev
15. clean 1 1 Select the cleaning equipment to be used Introduction All cleaning tasks require the selection of the right equipment to complete the job This section identifies a range of cleaning equipment and provides an indication of use and some relevant detail Overview The type of cleaning equipment found in businesses will vary Some have just the basics many will have only domestic cleaning equipment that is suitable designed for homes rather than commercial or industrial cleaning equipment Generally commercial or industrial equipment is better because it is e Sturdier e Larger capacity e Fitted with larger electric motors where applicable Other places boast an extensive range of the latest cleaning equipment with the correct item for every cleaning job that needs doing The cleaning storeroom Cleaning equipment is usually kept in a dedicated storage area this may be a purpose built cleaning storeroom where equipment utensils cleaning chemicals and protective clothing is kept Alternatively equipment may be kept in an assortment of cupboards or other locations around the premises as space allows There are often legislated requirements applying to the storage of cleaning chemicals ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean Large equipment Vacuum cleaners Whatever the shape size or style of vacuum cleaners their job is to
16. e Cleaning drainage holes grates to remove debris dirt which has accumulated there as part of the cleaning process there may be a requirement to add deodorant e Conducting a final visual inspection of the job and undertaking any follow up cleaning as required e Drying the area with mops or clothes or allowing it to air dry e Removing any protective cloths or similar which were installed to keep areas products dry during the pressure washing process e Returning any items which were removed back to their original position e Turning on any items which were turned off as if required e Advising staff and supervisors as required the cleaning job is complete e Opening the area up unlocking opening doors and gates taking down chains and removing barricades e Taking away safety signage which was put in place e Returning vehicles to designated locations e Recording completion of cleaning e Dealing with lost and found items ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques 4 5 Clean check and store equipment and chemicals Introduction Cleaning and checking and storing activities need to be undertaken after pressure washing have been completed This section addresses the usual requirements in this regard Cleaning locations Cleaning of pressure washers may be undertaken e Inthe cleaning store room e In a designated cleaning room e n nominated
17. e Wall cleaning full wall cleaning top to bottom as opposed to spot cleaning e Stain removal from Carpets Furniture Drapes e Cleaning of chandeliers and light fittings and fixtures e Hard floor maintenance which can require Stripping Re sealing e Cleaning ceiling fans and air conditioning outlets vents e Vacuuming inside furniture e Deep cleaning that is a much more detailed cleaning covering every aspect of the item of nominated appliances and furniture ASEAN 2015 88 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Preparation activities prior to moving to the work area Before arriving at the worksite there may will be a need to Obtain work order from supervisor Load cleaning cart trolley On arrival at work area The following activities are standard before cleaning begins Notifying required persons cleaning is about to start Emptying ashtrays Cleaning wiping and polishing ashtrays as required to optimise appearance Picking up loose litter Picking up lost and found items Emptying rubbish containers Erecting appropriate warning signs in the location being cleaned Moving and removing furniture and fittings as required Moving a vehicle which has to be cleaned to a safe location or designated cleaning washing bay Understanding organisation specific directions instructions applicable t
18. from the following Hold the tip of the lance the nozzle approximately 60cms to one metre from the surface to begin with the standard technique is start further away and move closer as required to remove soil Spray at about a 45 angle this will helo move the water and debris away and avoid damage through direct vertical contact between the jet of water and the surface Move the spray in a gentle and rhythmical sideways motion moving the spray from side to side Vary pressure water flow detergent angle distance duration and nozzle setting as required to achieve optimum results high level results are not always the result of set and forget Not all pressure washing requires use of maximum settings Work from top to bottom on vertical surfaces Spray wooden surfaces in a downward arc as opposed to spraying directly into onto the surface of the wood Avoid spraying cracked damaged surfaces as pressure may cause further damage e Supplement pressure washing with other techniques as required to achieve the required level of cleaning this can require Detailing Hand washing Scraping e Rinse after cleaning with detergent has occurred this May require rinsing of the surface which has been cleaned Will require rinsing flushing of the unit e When cleaning vehicles ensure Designated cleaning washing bays are used as they will usually have
19. is a need to use and or wear personal protective equipment and clothing This section identifies the items available in this regard and presents basic requirements in relation to their provision and use Protective items PPE may include e Overalls and jackets which may be the standard cleaning uniform or provided specially for use at designated times for nominated cleaning tasks e Aprons which may include material aprons leather aprons and PVC aprons e Gloves either thick rubber gloves PVC gloves or longer and stronger gauntlets e Cotton glove inserts e Breathing apparatus e Waterproof clothing and footwear rubber boots e Eye protection goggles safety glasses and face masks e Ear hearing protection e Enclosed shoes and steel capped boots e Safety hats hard hats headwear and helmets food handlers also use hairnets and beard nets e High visibility vests e Uniform to be worn which can include long trousers and long sleeved shirts Where staff are required to work outside in the elements PPE can include sun hats broad brimmed hats sun glasses and sun protection as well as rain coats warm clothing Useful websites Take a look at the following to get an idea of what is available by visiting http www safetyequipment net au http www2 protectoralsafe com au http www seton net au ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean Safe
20. items e Changing filters and bags e Changing pads e Changing belts e Recharging batteries for battery powered units Maintenance requests Where further work needs to be done to equipment these situations must be reported Reports may need to be made verbally or in writing ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Storing equipment Requirements include Storing stowing in accordance with enterprise requirements Locating all items in their designated places Ensuring items are easy for the next person to access use Making sure all attachments are stowed with the equipment Completing any internal logs registers required Storing chemicals All chemicals must be stored after use Never disposing of left over chemicals in undiluted form down a sink or gully trap Wearing appropriate PPE when storing chemicals Returning chemicals to designated locations Storing chemicals with labels facing to the front Checking each bottle container to ensure no leaks damage and lids seals are tight Visually checking other chemicals and containers in the store at the same time When spilt chemicals should be initially soaked up with sand earth or some kind of designated absorbent material Leaving already de canted chemicals in spray bottles Securing the chemical store to prevent unauthorised use of the chemicals Disposing of any chemicals which have been diluted N
21. mounted items e Remove dust and flies insects from window sills Sweeping Sweeping is done to remove dust and other debris In some cases sweeping may be the entire cleaning job needing to be done but in many cases sweeping is a preparatory task for wet mopping or stripping a floor for re sealing When sweeping e Pick up loose litter and debris by hand first e Choose the right broom for the job softer brooms for internal work and brooms with stiffer bristles for outside work e Consider dust mopping as an alternative e Be mindful of the potential for raised dust and work to minimise it slower strokes results in less dust e Sweep in a structured planned manner Push or pull the broom as most appropriate Work systematically through the area to be cleaned Overlap strokes of the broom to obtain proper coverage Clean behind doors e Avoid damage to walls skirting boards furniture and other items ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques dry area cleaning techniques e Clean under items as required be prepared to move small items e Sweep up the collected dust debris using a dustpan and brush Sweeping driveways and parking lots A standard outdoor servicing requirement is to sweep driveways and parking lots The cleaning of driveways and car parks should also embrace the cleaning of footpaths as well as servicing external walkways within the b
22. not dominate or over power Urinal blocks are also used to mask smells in gents toilets when using them follow the recommended dosage rate do not simply throw handfuls of them into the trough urinal They are expensive and on their own they do not provide any cleaning function e There is still a need to clean the urinal even where these blocks are used ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean Pesticides These are used to e Kill flies and insects e Deter flies and insects Sanitisers Sanitisers are used to kill bacteria micro organisms and or reduce their numbers to a safe level Surfaces should be cleaned with a detergent before a sanitiser is applied There may be a need for the sanitiser to remain in contact with the surface for a nominated period X seconds before it is removed rinsed off Chemical company websites Visit the following to see the products available www agar com au www cleaningshop com au Material Safety Data Sheets Material Safety Data Sheets must be available for every cleaning chemical or agent used Learn where these sheets are kept and read and understood them for all the products used Employers are also required to ensure all chemicals used in the workplace are accompanied by a Material Safety Data Sheet They must be kept near the chemicals and they cover issues such as Product classification Storage requirements Tran
23. outlets fitted with Residual Current Devices General instructions When operating a pressure washer Follow manufacturer s instructions and organisational training Never be afraid to ask for advice or help if faced with a difficult or unique situation Make sure items not being pressure washed are protected covered to Protect them from getting wet or becoming damaged Gi Si a a x CS f See Ss E g SW e Stop them moving toppling when struck by the water stream Move items which cannot be covered to protect them from damage this may include living plants small ttems equipment furniture and or stock Pick up all loose large items of litter rubbish ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques e Connect to water e Flush the system prior to using it e Ensure most appropriate correct nozzle is fitted according to requirements of the job e Pre spray areas to be cleaned to pre wet soak them as part of the cleaning process If using detergents or chemicals there may be a need to allow contact time five to ten minutes before doing further cleaning wok or rinsing e Follow manufacturer s instructions regarding all chemical use e Pressure wash the area to be cleaned using the following as general advice and ensuring enterprise procedures and manufacturer s instructions are followed where they differ
24. outside locations Need to clean items Equipment needs to be cleaned after use so as to e Prevent odour problems e Maintain a high level of appearance e Maximise operational effectiveness e Leave the items ready for use next time they are needed Cleaning the pressure washer Always make sure there is compliance with the specific cleaning instructions for the unit as prescribed in the User Operator Instructions contained in the Manual for the machine Indicative actions include e Turn machine off e Turn water supply off e Release pressure and residual water from machine by activating trigger gun e Disconnect from power and water e Disconnect wand trigger gun spray e Drain flush and rinse water feed hose e Drain flush and rinse detergent chemical feed hose e Drain the tank e Flush the nozzle with clean water Never stow store the machine without flushing it Use a nozzle cleaner to dislodge material which clogs the hole ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques Flush again after cleaning nozzle Ensuring nozzles are clear and clean is an important aspect of maintaining a pressure washer in peak operating condition e Remove and clean the inlet filter a small brush should be used to gently scrub this rinse afterwards and re fit or replace if necessary e Clean the tank of dirt paying special attentio
25. room work in one direction either clockwise or counter clockwise direction to Avoid re tracing steps Work in a structured way which helps eliminate the possibility of tasks being overlooked Work from top to bottom this allows dust debris to fall to floor or lower levels or flat surfaces which will subsequently be cleaned after higher items Do two things at once such as checking the condition of items lights lamps switches TVs and other items in the room area space at the same time as cleaning them tidying them Pre soak items which need washing before attempting to clean them e Only apply cleaning solutions direct to surfaces only in accordance with manufacturer s instructions in advance of actual cleaning to assist with final cleaning Use the head to save the feet this means thinking to save effort trips to the cart trolley e For example any trip to the trolley can nearly always serve two purposes if something is taken to the trolley used cleaning materials dirty linen rubbish Purpose 1 thought should be paid to what can be taken back fresh linen chemicals cleaning tools replacement items Purpose 2 to save time and effort Put items in the same place every time whether on the cart trolley or in a space area this saves time searching for those items ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques
26. sills and picture frames these are the places where cobwebs and dust traditional gather e Cleaning from dirtiest to cleanest e Using adamp cloth or duster when dusting e Using a cobweb broom to remove cobwebs e Using equipment extensions ladders or scissor lift to reach high places e Cleaning inside door frames using a damp cloth or duster Cleaning walls Walls may be spot cleaned daily a full cleaning of the walls is part of periodic scheduled cleaning Walls are not cleaned unless there are marks on them or unless it is time for a periodic full clean of the walls Points to note include e Doors should be regarded as walls always ensure the area behind the door is cleaned e Clean from top to bottom where large areas entire walls need to be cleaned e Wipe clean tiles walls adjacent to sinks basins to remove water marks and spots e Use designated general purpose cleaner sprayed either onto a cloth sponge or sprayed directly onto wall according to instructions for individual products cleaning agents adhere to requirements for contact time if applicable e Rinse and dry using sponge or paper towel not loose running water e Wipe clean the light switches and controls for fans and other items ensure hands are dry e Wipe power points turn switches to the off position ensure hands are dry Online videos Watch the following for more advice http www youtube com wat
27. suck up dust and dirt off floor surfaces and drapes Most vacuum cleaners have a variety of attachments designed for specific purposes Such as crevice nozzles extensions brushes Dry vacuum cleaners can only be used on dry surfaces and to suck up dry material and not liquids water Wet vacuum cleaners are designed to suck up liquid spills and can be used for wet cleaning of carpets Double check the vacuum cleaner to verify it is designated as a wet vacuum cleaner before using it on liquids some vacuum cleaners are dual purpose and can be used on wet or dry surfaces Back pack vacuum cleaners are used in many situations where it would be difficult or time consuming to use a machine that is pulled along the floor such as when vacuuming between tables and chairs A backpack style cleaner also reduces tripping hazards although the cord still presents a hazard unless a battery powered unit is being used Some companies refer to vacuum cleaners as extractors Have a look at different vacuum cleaner options at http www powervac biz http www powersweep com au http www gepro com au ics profile asp http www nilfisk advance com au Carpet shampoo machines Carpet shampoo machines can also come in a variety of shapes sizes and styles As their name suggests they are used to shampoo dry clean and or steam clean carpeted surfaces They may also be referred to as extractors Remember carpet
28. the area to be cleaned and the condition of the surfaces to be cleaned which may require Visual checking to ensure no danger or damage will result from the process Following guidance provided in a site area or equipment specific inspection checklist which will need to be completed tick boxes checked signed and dated issues noted as part of the process Avoiding damaged surfaces Equipment surfaces which are damaged may need to be cleaned using another technique as pressure washing will readily cause more damage to already damaged surfaces Already damaged surfaces which may need to be avoided can include Any surface of any construction which is chipped cracked or split Coatings paint which is lifting or peeling ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques 4 2 Prepare worksite Introduction Worksites needing to be pressure washed will need to be prepared This section explains pressure washing discusses timing of pressure cleaning and identifies the preparation required What is pressure washing Pressure washing is a process where water is sprayed at high pressure against a surface to clean it some refer to this as water blasting Features of the process are e The water may have detergent fed into it by an injector system incorporated into the washer e The water may be hot or cold depending on the surface being cl
29. the supplies tools equipment and chemicals cleaning agents to be used and how to use them ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques The following is an example of what may be available Wet mopping Wet mopping is also referred to as damp mopping The following represents instructions a business may provide and are presented only as being indicative of what may apply in a workplace Where the employer has different directions their specifications must be adhered to ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques Wet Mopping SOP Prepared by Date Step Hazard Type and Rating Prepare the area Physical slips and trips Low Prepare equipment and Chemical materials Low Mop the floor Chemical and Physical Medium Clean up Chemical and Physical Low ASEAN 2015 Trainee Manual Clean premises and equipment Actions precautions required Set up Cleaning in progress signs Pick up loose rubbish Move items that present obstacles Sweep the floor Put on safety gloves and glasses Fill mop bucket with warm water Add 250 mis XYZ detergent use red measuring jug Move mop and bucket to area to be mopped Put mop in bucket to wet it thoroughly Use rollers to wring mop until damp Apply mop to floor use 8 patter
30. the workplace cleaning store and use them where appropriate These specialty products have been developed for e A range of floor and carpet cleaning needs specific for different surface types tile linoleum vinyl carpet wood and specific stains dirt of types of damage e These include stripping and re sealing products for hard floor surfaces Windows and glass Stainless steel Leather Aluminium Toilets Various laundry uses for washing clothes and linen e Cleaning specific equipment and areas such as rubbish bins smokehouses vehicles furniture polishes Solvents Solvent based detergents will dissolve heavy grease and oil It is most important to realise not all surfaces can be cleaned with solvent detergents For example it would not be appropriate to remove oil spilt onto a lounge suite with a solvent detergent however a metal surface could remain unharmed if cleaned with a solvent detergent Again refer to the manufacturer s instructions when using such a cleaning product Remember solvent based detergents may be harmful to the skin They should be treated with care and spillage should be avoided at all times Surfaces cleaned with solvents must be rinsed thoroughly to remove any harmful residue ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean Polishes Polish protects surfaces and forms a barrier against liquids which may har
31. with labels facing the front for ease of identification reading the label ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques Checking each bottle container stored to ensure No leaks or damage Lids seals are tight Visually checking other chemicals and containers in the store at the same time to identify leaks spills or dangers issues When spilt chemicals should be initially soaked up with sand earth or some kind of designated absorbent material see follow relevant MSDS Leaving already de canted chemicals in spray bottles rather than returning them to larger drums containers securing the chemical store to prevent unauthorised use of the chemicals Disposing of any chemicals which have been diluted as they will have lost the cleaning power of their active ingredients by the next time they are used Never storing chemicals with foodstuffs beverages or containers which will be used to serve hold food or drinks Never storing chemicals in food containers Never eating drinking or smoking when handing storing chemicals Always washing hands after storing chemicals at the completion of cleaning Replenishing consumables One of the last tasks required at the end of a shift is to check supplies in the cleaning or chemical store so supplies can be ordered or replenished Experience coupled with management guidelines relating to the levels of stock wil
32. Clean premises and equipment D2 TTO CL4 03 Trainee Manual Clean premises and equipment D2 TTO CL4 03 Trainee Manual i William g o Australian A liss Zes Aid ad Institute amp hospitality Australian William p Aa GD Aiidliss Project Base William Angliss Institute of TAFE 555 La Trobe Street Melbourne 3000 Victoria Telephone 03 9606 2111 Facsimile 03 9670 1330 Acknowledgements Project Director Wayne Crosbie Project Manager Jim Irwin Chief Writer Alan Hickman Subject Writer Alan Hickman Editor Jim Irwin DTP Production Daniel Chee Mai Vu Cindy Curran The Association of Southeast Asian Nations ASEAN was established on 8 August 1967 The Member States of the Association are Brunei Darussalam Cambodia Indonesia Lao PDR Malaysia Myanmar Philippines Singapore Thailand and Viet Nam The ASEAN Secretariat is based in Jakarta Indonesia General Information on ASEAN appears online at the ASEAN Website www asean org All text is produced by William Angliss Institute of TAFE for the ASEAN Project on Toolbox Development for Front Office Food and Beverage Services and Food Production Divisions This publication is supported by the Australian Government s aid program through the ASEAN Australia Development Cooperation Program Phase II AADCP II Copyright Association of Southeast Asian Nations ASEAN 2015 All rights reserved Disclaimer Every effort has been made to en
33. It is a requirement of this Unit you complete Work Projects as advised by your Trainer You must submit documentation suitable evidence or other relevant proof of completion of the project to your Trainer by the agreed date 1 1 Prepare a comprehensive list of small and large cleaning equipment which may be found in an industry business and identify what each item may be used for 1 2 Identify the chemicals you would use to Clean service counters Polish wooden furniture Deodorise the air in a room Clean windows Kill flies and insects Kill bacteria 1 3 List the PPE and clothing which may be needed by staff undertaking a wide range of wet dry and pressure washing cleaning duties in a business 1 4 Identify one item of electrically powered cleaning equipment and prepare a set of sample directions instructions or guidelines which could be used by staff to check its operation and safety ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean Summary Prepare to clean When preparing to clean Select the required small and large equipment Use industrial commercial items where possible Attach the right pad to a polisher for the work to be done Consider loading a cleaning cart trolley to carry the equipment items Make sure there are rubbish containers for disposal of collected dirt garbage Obtain necessary warning signs ancillary equipment and PPE Select the required chemicals and
34. The unit descriptor describes the content of the unit you will be studying in the Trainee Manual and provides a table of contents which are divided up into Elements and Performance Criteria An element is a description of one aspect of what has to be achieved in the workplace The Performance Criteria below each element details the level of performance that needs to be demonstrated to be declared competent There are other components of the competency standard e Unit Title statement about what is to be done in the workplace e Unit Number unique number identifying the particular competency e Nominal hours number of classroom or practical hours usually needed to complete the competency We call them nominal hours because they can vary e g sometimes it will take an individual less time to complete a unit of competency because he she has prior Knowledge or work experience in that area The final heading you will see before you start reading the Trainee Manual is the Assessment Matrix Competency based assessment requires trainees to be assessed in at least 2 3 different ways one of which must be practical This section outlines three ways assessment can be carried out and includes work projects written questions and oral questions The matrix is designed to show you which performance criteria will be assessed and how they will be assessed Your trainer and or assessor may also use other assessment methods includin
35. a dry cloth to remove any wetness remove smears and buff the surface Re position items on tables to create an attractive presentation books magazines promotional materials flower arrangements ash trays Check under cushions for lost property be alert to the possible presence of sharp objects needles Move small items of furniture so they can be vacuumed underneath Re position items of furniture which may have been moved re located by staff to their normal designated location ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Polishing metal Polishing metal is a standard practice remaining essentially the same regardless of the metal to be polished The two things which change between different metals are e The polish used by type and brand name e he cloths used to apply and remove the polish these need to be non abrasive Polishing will involve e Wearing protective gloves e Selecting the correct polish for the metal to be polished and the job to be done e Reading knowing the manufacturer s instructions for each polish used e Spreading the polish for example brass or silver over the entire surface to be clean with the appropriate cloth this can be one used to apply the same polish type to a previous surface there is no need for a clean application cloth for each new item surface e Rubbing the surface with
36. a fresh cloth one that has not been used on anything else or for anything else while the polish is still moist unless manufacturer s instructions specify otherwise Attention must be paid to Removing polish from nooks and crannies so the polish does not accumulate dry and look unattractive Removing all the polish Using a circular motion as opposed to an up and down or side to side action Achieving the required level of shine and gloss Visit http Awww englishcustompolishing com index html for several interesting hints and facts Dusting and tidying Dusting must be done before vacuuming A damp cloth wetted with water and or general purpose detergent cleaner may be used for dusting Generic processes are e Wipe tops flat surfaces polish as required e Wipe table desk and chair legs polish as required e Position chairs at tables e Position room furniture as required by floor plan use of the space room e Dust clean outside of all sideboards cupboards and cabinets spot clean as required clean inside of drawers ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques e Check under all cushions in the room take care be alert to the possible presence of sharp objects needles e Tidy arrange brochures advertising materials and magazines on tables desks and service counters e Supply necessary r
37. activities The exact nature of finishing activities required will depend on e The preparation activities which were done there is a general need to undo what has been done in terms of preparation work e Whether the business is open or closed which influences for example items needing to be turned on or off and whether or not doors are opened closed locked or unlocked Each cleaning task is potentially unique so the following is indicative of what may be needed rather than prescriptive e Tidying the area which may involve Removing drop sheets and protective cloths materials placed over items as part of the preparation process Arranging re arranging the furniture this may require taking a photo of things before work starts perhaps on a cell phone Placing items in designated assigned areas as described in a floor plan layout for the room space or area Returning excess items items which are in the wrong place to other storage areas or to their correct location Removing warning signs cones and other barriers or tapes which were put in place Removing cleaning equipment carts materials and chemicals and other requisites Performing touch ups which may involve Spot cleaning of areas not fully clean Drying of wet spots e Finalising the work such as if and as appropriate to the area Placement of products books magazines promot
38. ainted surfaces e Wood surfaces e Brick surfaces e Metal surfaces e Upholstery or material in vehicles Examples of fittings There is a very wide range of items fittings which may need to be cleaned such as but not limited to e Security cameras e Ceiling fans e Lights e Smoke detectors e Speakers e Sprinkling systems e Televisions e Vents and grilles e Interiors of vehicles Soil types Common soil types which may need to be cleaned can cover e Dirt and dust e Smoke e Water e Food e Blood e Oil and grease ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques 5 2 Select appropriate equipment and chemicals Introduction For each job to be completed the correct equipment and chemicals must be selected This section presents criteria for choosing what is needed and gives an overview of equipment and chemicals which may need to be used Criteria for determining what is needed Determining equipment and chemicals required for cleaning ceilings surfaces and fittings is achieved through a combination of e Undertaking activities involved in assessing identifying the work to be done see previous section e Reading and applying the specifications as described in the SOPs Wls for the business Equipment which may be required Having a well equipped cart trolley is vital to efficiently and effectively cleaning c
39. and stored the equipment which was used 3 2 Provide video photographic real time or other acceptable evidence you have dry vacuumed an area providing evidence you have e Assessed the area to be cleaned e Prepared the worksite job e Applied appropriate techniques e Tidied and returned the area to service e Cleaned checked and stored the equipment which was used 3 3 Provide video photographic real time or other acceptable evidence you have dusted an area providing evidence you have e Assessed the area to be cleaned e Prepared the worksite job e Applied appropriate techniques e Tidied and returned the area to service e Cleaned checked and stored the equipment which was used ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Summary Apply dry area cleaning techniques When applying dry area cleaning techniques Assess the job and work to be done Plan the work Prepare the job worksite Apply appropriate techniques depending on the job to be done Adhere to internal SOPs WIs Wear use designated PPE Undertake clearing and pick up of loose items and litter as a basic first step Tidy worksite before returning it to service Clean check and store cleaning equipment and PPE after completion of task s Take action to replace replenish used items ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques dry area cleaning techniques
40. ch v aEjJ6LDC_y7A Housekeeping Training Video for Professional Cleaners 5 mins 3 secs http www youtube com watch v f CWhrgGis8 Washroom cleaning training video 8 mins 2 Secs http Awww youtube com watch v f3VVFUJmmWs Fairfield Inn and Suites by Marriott Housekeeping Training 10 mins 29 secs http video about com housekeeping How to Clean a Ceiling Fan htm How clean a ceiling fan 2 mins 49 secs http video about com housekeeping How to Clean Ceiling Vents htm How to clean ceiling vents 1 min 27 secs ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques 5 5 Tidy worksite Introduction Areas need to be returned to service when they have had their ceilings surfaces and fittings cleaned This section repeats the information provided in section 3 4 Tidy workstation after dry cleaning techniques have been applied Finishing activities The exact nature of finishing activities required will depend on the preparation activities which were done and may require e Tidying the area Removing drop sheets and protective cloths materials Arranging re arranging the furniture Placing items in designated assigned areas Returning excess items to other storage areas or to their correct location Removing warning signs cones and other barriers or tapes Removing cleaning equipment carts materials and cleaning chemicals Perfor
41. chniques e Hosing which can involve Use of a standard water hose with nozzle to Pre spray pre wet an area prior to application of chemicals or cleaning activity Remove dirt and debris Rinse e Scrubbing which can involve the use of Scrubbing brushes water and detergent Abrasive pads e Wet wiping which is the use of damp cloths wetted with water or detergent cleaning agent to clean a surface Organisational directions requirements Many enterprises have protocols to follow when undertaking certain cleaning tasks These may be referred to as e Standard Operating Procedures SOPs e Work Instructions Ws Where these are in place e Appropriate training will be provided as part of the on the job training e They will have been developed for use with equipment and chemicals used by the business e They must be followed SOPs WIs are provided to guide the action of staff when cleaning public areas rooms or individual items areas They are provided to ensure e Work is completed to a set standard level of quality e Work is completed safely e Work is completed in the most efficient manner in terms of cost and time Where they are provided they must be adhered to there is no choice in this they must be followed They e Are very prescriptive e ldentify hazards associated with the task and prescribe action to minimise danger to workers and customers e Specify
42. cleaned A standard item is a dust pan and brush set for cleaning up small spills some will use a small portable re chargeable vacuum cleaner for this Have a look at http www cleancare com au dusters brushes brooms handles w1 i1002536 http www unoclean com Commercial Janitorial Brooms Brushes Accessories aspx Cloths and sponges Cloths and sponges are used to clean a variety of surfaces Sponges are used for damp cleaning needs and cloths are used for cleaning polishing and dusting They can be made from a variety of materials but are generally lint free They are used with a cleaning agent Some cloths are made from material and some are disposable paper based Buckets Buckets are available in a variety of shapes sizes and styles and are generally made from either galvanised steel or plastic some buckets have wheels castors for ease of mobility others only have a handle Buckets are used to hold water and cleaning agents Mop buckets feature rollers to remove excess water from the mop head prior to use Visit ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean http www masteraustralia com au and click on Buckets in the left hand side Browse Catalogue this site can be used to look at many other items of cleaning equipment mentioned in these notes It is worth bookmarking for future reference Garbage receptacles Nearly all cleaning tasks will r
43. cleaning agents Refer to Product Usage Charts SOPs or Wis to identify chemicals required Know where the MSDS are located and what they contain Handle chemicals safely and with care Check all equipment is safe to use operate Never use unsafe equipment items ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to lean to clean ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques Element 2 Apply wet area cleaning techniques 2 1 Assess areas to be cleaned Introduction All areas to be cleaned must be assessed before cleaning activities begin This section discusses the assessment stage of a cleaning job Assessing the job Overview of the process Assessment of the task is part of planning and preparation for the job Assessment is undertaken through a combination of the following three activities e Looking at the area job visually inspecting the area e Talking to people who have input to make about the area items to be cleaned or who have responsibility for the area e Using personal knowledge and experience as key reference points for determining and evaluating what needs to be done Specifics of each job When assessing the task area considerations are e Determine the extent of the work to be done for example Isa full clean required or just spot cleaning Is the area very dirty Is there graffiti damage What sort of di
44. d appropriate techniques Tidied and returned the area to service Cleaned checked and stored the equipment which was used 5 3 Provide video photographic real time or other acceptable evidence you have cleaned nominated fittings providing evidence you have Assessed the area to be cleaned Selected appropriate equipment and chemicals Prepared the worksite job Applied appropriate techniques Tidied and returned the area to service Cleaned checked and stored the equipment which was used ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Summary Apply ceilings surfaces and fittings cleaning techniques When applying ceilings surfaces and fittings cleaning techniques Assess the areas and work to be done Plan the work Prepare the job worksite Select appropriate equipment and cleaning chemicals Apply appropriate techniques depending on the job to be done Adhere to internal SOPs WIs Clean to internal standards criteria using appropriate techniques Work efficiently but avoid rushing Wear use designated PPE Be alert to the dangers posed by cleaning furniture hidden places Maintain positive customer relations Undertake clearing and pick up of loose items and litter as a basic first step Tidy worksite before returning it to service Clean check and store cleaning equipment and PPE after completion of task s Take action to replace replenish used i
45. d from Trove National Library of Australia at http trove nla gov au Andrews S 2006 3 reprint Hotel Housekeeping Training Manual Tata McGraw Hill New Delhi Dukes R 2005 7 ed n Pool surfaces problems and solutions Techlines Indian Rocks Beach Florida Findley M amp Formichelli L 2005 The complete idiot s guide to cleaning Alpha Books Indianapolis In Jones T J A 2007 5 ed n Professional management of Housekeeping Operations John Wiley and Sons Hoboken New Jersey McKenzie D 2007 Housekeeping student learning guide Certificate IV in Hospitality supervision Regency Publishing Regency Park South Australia McKenzie D 2007 Housekeeping assessment guide Certificate IV in Hospitality supervision Regency Publishing Regency Park South Australia Talwar P ed 2006 Hotel and Hospitality Management Housekeeping sha Books Delhi Tamminen T 2005 The ultimate guide to spas and hot tubs McGraw Hill New York Maidenhead Wiggins Jane M 2014 Facilities managers desk reference Second edition Chichester West Sussex John Wiley amp Sons ASEAN 2015 Trainee Manual Clean premises and equipment Recommended reading ASEAN 2015 Trainee Manual Clean premises and equipment Trainee evaluation sheet I A Trainee evaluation sheet Clean premises and equipment The following statements are about the competency you have just completed
46. d may infer a lack of cleanliness in other parts of the establishment Buckets should be free of leaks not smelly and have secure handles Check and clear around the rollers on mop buckets to avoid the build up of debris and fibres from the mop ltems to be used need to sufficient in number there needs to be enough cleaning cloths disposable gloves or other resources to get the job done Items must be appropriate for task many instances of damage or injury have resulted from trying to complete a cleaning job without the right tools Make sure all necessary attachments for vacuum cleaners polishers washers are taken before leaving the cleaning store to enable all planned task to be completed this saves time and effort All electrically powered and battery powered items must be used strictly in accordance with manufacturer s instructions if this is unknown read the instructions or ask an experienced staff member to explain demonstrate what to do A standard check with any piece of electrical equipment is to ensure the electrical cord is safe to use not frayed or broken and with no wires exposed Make sure battery operated equipment is adequately charged before using it low battery power can adversely affect cleaning performance and causes time loss when the job has to be interrupted to remedy the situation ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to lean to clean Work Projects
47. dicative and may be used where no alternative exists Check what applies in the workplace and where these differ to what is provided adhere to house requirements If in doubt ask the supervisor Cleaning locations Cleaning of cleaning items equipment may be undertaken e Inthe cleaning store room e In a designated cleaning room e n nominated outside locations Need to clean items Equipment needs to be cleaned after use so as to e Prevent odour problems e Maintain a high level of appearance e Maximise operational effectiveness e Leave the items ready for use next time they are needed Mops Dusting mops After use e Shake thoroughly in appropriate location outside e Wash in hot soapy water e Hang out to air dry Washing mops On a regular basis mops should be e Washed in hot soapy water and rinsed thoroughly e Squeeze dried ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques e Hung up to air dry e Sanitising may be required Dusters Cleaning of dusters involves e Shake clean regularly in an appropriate outside area e Wash in accordance with the manufacturer s instructions Brooms and brushes Cleaning of brooms and brushes involves e Shake clean e Wash in hot soapy water e Rinse e Air dry Cloths and sponges These should be e Cleaned on a regular basis using hot soapy water e Left to air dry Buckets
48. e for individual items e Maintaining as required such as replacing filters on masks respirators e Checking for rips and tears to gloves and aprons e Checking for holes leaks in safety shoes boots e Verifying the integrity of safety glasses Conducting safety checks Safety checks must be undertaken on all equipment as part of their cleaning and storing Activities include e Reporting problems issues identified during cleaning processes e Removing unsafe items from use e Following manufacturer s instructions regarding regular inspections and checks e Checking all attachments and cords Undertaking preventative maintenance and repairs Only basic maintenance and repairs will be required Other maintenance and service must be performed by suitable qualified technicians What is classified as basic maintenance and repairs can vary between businesses and vary with the equipment being used but may include e Adding fuel to petrol and diesel driven units ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques e Greasing and oiling parts e Emptying items basic maintenance for items such as vacuum cleaners and other items that incorporate a vacuuming function must be emptied as a routine maintenance activity e Changing filters and bags in vacuum cleaners e Changing pads on polishers e Changing belts on belt driven items e Rechar
49. e the required competency standard ASEAN has adopted the CBT CBA training system as it is able to produce the type of worker that industry is looking for and this therefore increases trainee chances of obtaining employment CBA involves collecting evidence and making a judgement of the extent to which a worker can perform his her duties at the required competency standard Where a trainee can already demonstrate a degree of competency either due to prior training or work experience a process of Recognition of Prior Learning RPL is available to trainees to recognise this Please speak to your trainer about RPL if you think this applies to you What is a competency standard Competency standards are descriptions of the skills and knowledge required to perform a task or activity at the level of a required standard 242 competency standards for the tourism and hospitality industries throughout the ASEAN region have been developed to cover all the knowledge skills and attitudes required to work in the following occupational areas e Housekeeping e Food Production e Food and Beverage Service ASEAN 2015 Trainee Manual Clean premises and equipment Introduction to trainee manual e Front Office e Travel Agencies e Tour Operations All of these competency standards are available for you to look at In fact you will find a summary of each one at the beginning of each Trainee Manual under the heading Unit Descriptor
50. e used Handwritten work must be legible and should also be well spaced to allow for ease of reading New paragraphs should not be indented but should be separated by a space Pages must be numbered If headings are also to be numbered students should use a logical and sequential system of numbering ASEAN 2015 Trainee Manual Clean premises and equipment Presentation of witen work of written work Cover Sheet All written work should be submitted with a cover sheet stapled to the front that contains e The student s name and student number e The name of the class unit e The due date of the work e The title of the work e The teacher s name e A signed declaration that the work does not involve plagiarism Keeping a Copy Students must keep a copy of the written work in case it is lost This rarely happens but it can be disastrous if a copy has not been kept Inclusive language This means language that includes every section of the population For instance if a student were to write A nurse is responsible for the patients in her care at all times it would be implying that all nurses are female and would be excluding male nurses Examples of appropriate language are shown on the right Barman maid Bar attendant Waiter waitress Waiter or waiting staff ASEAN 2015 Trainee Manual Clean premises and equipment Recommended reading reading Recommended reading Note all Recommended Reading is source
51. eaned the chemical being used and the soil being removed e A trigger spray gun wand controls the spray applying it in a pattern concentration depending on the nozzle selected for the job to be done e Different nozzles direct the water in different degrees of spray 0 being the most concentrated spray for heavy cleaning through 15 25 suitable for general purpose cleaning nozzles 40 and the widest 60 65 e Nozzles may be colour coded for ease of identification to indicate their use type e A pump within the machine generates the pressure which forces the water out at high pressure Types of machines Pressure washers may be e Electrically powered operating from a power point e Gas petrol or diesel powered which normally produce a higher pressure spray and hence increased risk of danger and are most commonly used for outside areas Danger It is vital those who are required to use pressure washers receive proper training before they use the equipment and also receive suitable supervision when initially operating them Pressure washers have the potential to be very dangerous and can cause severe injury removing flesh if operated incorrectly ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques Preparing to pressure wash Timing of pressure washing Preparation for pressure washing is different to preparatio
52. eas such as driveways car parks and building exteriors e To clean exteriors of vehicles Visit the following to see examples of types and models available http www auswaterblasters com au www aatachservice com Small equipment Mops Mops are generally made from cotton or cotton polyester blends The three main types of mops are e Dusting mops to clean skirting boards and polished surfaces e Polishing mops for buffing and polishing e Washing mops to wash floor surfaces or apply sealant to floors that have been stripped and need to be re sealed Brooms and brushes Brooms and brushes can be made from a variety of materials ranging from straw to a synthetic coarse bristle like material Their purpose is to remove dust dirt and grime from surfaces They can come in all sizes and shapes They should be sufficient in number and variety as required for the cleaning task or as dictated by the establishment they must be clean and sufficiently bristled ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean The most common types of brooms and brushes are e Scrubbing brush e Sink brush e Wall brush e Soft broom e Speciality brushes e Cobweb brush e Vehicle wash brooms e Gong brush e Floor brooms e Yard broom stiff bristles for exterior use Not all businesses will require all types of brooms it will depend on the facilities and areas to be
53. eas will need either dusting or polishing Some will need cleaning on a daily basis while others may only need to be cleaned weekly Air conditioning vents Af y Doors including top ledge and handles B i Picture frames facing glass as well as frame Mirrors frame and mirror Skirting boards Furniture including Seat furniture remove cushions and check sides legs back and underneath Lamps clean bases shades and cords General items including built in and free standing items with attention required to top sides legs and underneath each item do not forget to clean inside the drawers Vehicles interiors only exteriors will require wet cleaning and perhaps polishing Windows glass and frames and window sills Walls check for cobwebs and marks Telephone main unit and hand receiver Outside balcony areas furniture ash trays ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Dry mopping Dry mopping is also known as dust mopping The following represents instructions an organisation may provide for staff in relation to Dry Dust Mopping Work Instruction Number 21 Dust Mopping Prior to Work e Remove loose rubbish and debris o Dust pan and brush o Protected hand gauntlets e Take correct size clean dust mop to area to be mopped e Wear dust mask and protective gauntlets Activity Dust moppi
54. eave exit doors open e Put on safety gloves and glasses e Pick up loose rubbish beware of potential for syringes e Empty bins fit new bin liners beware of potential for syringes e Replace toilet paper and soap e Sweep the floor e Fill trigger spray bottle ABC Brand disinfectant e Obtain 1 litre ABC Brand disinfectant e Obtain 1 litre XYZ Brand toilet bowl cleaner e Obtain pest aerosol spray e Obtain toilet blocks e Flush toilets and urinals e Apply undiluted XYZ Brand toilet bowl cleaner directly into toilet bowl and urinal leave to soak e Use spray bottle of XYZ Brand toilet bowl cleaner to spray seat hinges and hardware of toilet fittings and urinal fittings e Use designated toilet brush and bowl mop to clean urinal and toilet bowl clean splashback return areas under flushing rim e Clean exterior of bowls and top and bottom of seat rinse e Flush e Apply disinfectant to bowls and urinals and allow to stand add blocks to urinal 1 block per unit 1 block per metre Apply wet area cleaning techniques Check for damage Spot clean walls Mop floors Flush toilets and urinals Dry mop allow to air dry Clean up Chemical and Turn off exhaust fans Physical Remove safety warning signs Low Remove and dispose of rubbish picked up during preparation external dumper Clean toilet brush and bowl mop Dispose of protective gloves Return equipment and chemicals to storage Wa
55. ections instructions applicable to the job these may be SOPs Work Instructions Relevant internal standards and criteria e Putting on and or using necessary PPE and clothing for the job which is about to be done ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques How to interact with customers guests When servicing cleaning an area there is always the potential for customers guests to be present It is important to interact appropriately with them which may include e Greeting them when meeting them with an appropriate verbal greeting and smile e Informing of the service cleaning about to be undertaken e Asking for permission to clean the area items as necessary if appropriate e Cleaning another area if customers guests are present and returning at a later time e Providing responses to requests and queries e Referring customers to management if they make a request which falls outside personal scope of authority to deal with e Moving aside to allow customers guests to pass giving them right of way e Keeping noise and inconvenience to a minimum ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques 2 3 Clean wet areas Introduction The need to clean wet areas is a common requirement in all businesses This section defines wet areas and presents advice i
56. ed Element 2 Apply wet area cleaning techniques Performance Criteria 2 1 Assess areas to be cleaned 2 2 Prepare worksite 2 3 Clean wet areas 2 4 Tidy worksite 2 5 Clean check and store equipment and chemicals Element 3 Apply dry area cleaning techniques Performance Criteria 3 1 Assess areas to be cleaned 3 2 Prepare worksite 3 3 Clean dry areas 3 4 Tidy worksite 3 5 Clean check and store equipment and chemicals ASEAN 2015 Trainee Manual Clean premises and equipment Unit descriptor Element 4 Apply pressure washing techniques Performance Criteria 4 1 Assess area to be pressure washed 4 2 Prepare worksite 4 3 Clean areas using pressure washer 4 4 Tidy worksite 4 5 Clean check and store equipment and chemicals Element 5 Apply ceilings surfaces and fittings cleaning techniques Performance Criteria 5 1 Assess ceilings surfaces and fittings to be cleaned 5 2 Select appropriate equipment and chemicals 5 3 Prepare worksite 5 4 Clean ceilings surfaces and fittings 5 5 Tidy worksite 5 6 Clean check and store equipment and chemicals ASEAN 2015 Trainee Manual Clean premises and equipment Assessment mati matrix Assessment matrix Showing mapping of Performance Criteria against Work Projects Written Questions and Oral Questions The Assessment Matrix indicates three of the most common assessment activities your Assessor may use to assess your understanding of the conten
57. eilings surfaces and fittings ltems to be prepared and or loaded onto carts trolleys will include cleaning supplies and tools as well as required supplies amenities These can include e Vacuum cleaner this must be checked to see it is empty at the start of the shift soare bags are available where appropriate the machine is fully functional and there are no frayed cords or other safety problems a check should also be made to ensure all the vacuum machine tools accessories to be used are available e The vacuum cleaner is often not loaded on to the trolley but taken alongside the trolley some trolley designs allow a vacuum cleaner to be included to the cart e Mops ensure the mop head looks presentable and has been sanitised to kill bacteria and stop them being transferred from place to place e Mops may include wet mops for washing floors and or dry mops for polishing and dust mops for dusting skirting boards and hard floors e Brooms and brushes common types of brooms and brushes are Carpet brush Scrubbing brush Sink brush Silk brush Toilet brush Wall brush Cobweb broom ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Soft broom Tooth brush e Not al types will be required it will depend on the facilities to be cleaned e All carts trolleys should have a dust pan and brush set Buckets the
58. equipment Requirements include e Storing stowing in accordance with enterprise requirements e Locating all items in their designated places e Ensuring items are easy for the next person to access use e Making sure all attachments are stowed with the equipment e Completing any internal logs registers required Storing chemicals All chemicals must be stored after use e Never disposing of left over chemicals in undiluted form down a sink or gully trap e Wearing appropriate PPE when storing chemicals e Returning chemicals to designated locations e Storing chemicals with labels facing to the front e Checking each bottle container to ensure no leaks damage and lids seals are tight e Visually checking other chemicals and containers in the store at the same time e When spilt chemicals should be initially soaked up with sand earth or some kind of designated absorbent material e Leaving already de canted chemicals in spray bottles e Securing the chemical store to prevent unauthorised use of the chemicals e Disposing of any chemicals which have been diluted e Never storing chemicals with foodstuffs beverages or containers which will be used to serve hold food or drinks e Never storing chemicals in food containers e Never eating drinking or smoking when handing storing chemicals e Always washing hands after storing chemicals at the completion of cleaning Replenishing consumables Experience coupled with managemen
59. equire gathering and disposing of debris rubbish and waste so most cleaning tasks will necessitate the use of some form of waste receptacle A receptacle maybe e A solid item such as a bin e A disposable plastic bag e Abin liner placed inside a garbage receptacle that is built into a cleaning trolley cart Warning signs These are safety signs used when a public area is being cleaned to warn customers of the danger or when nominated back of house areas are being cleaned to warn staff delivery drivers repair people who are on the premises It may be standard procedures that they are displayed whenever cleaning duties are being undertaken regardless of location and regardless of the type of cleaning Examples of these can be seen at www hosidirect com au listProduct Cleaning Floor Signs Ancillary items There may also be a need to use some or all of the following e Electrical extension cords e Keys or cards for accessing areas e Communication devices so others can advise of relevant information or new jobs e Trolleys caddies carry alls and baskets for holding and transporting cleaning requisites to and from jobs e Door stops to keep doors open e Scouring pads and scrapers e Spray bottles for dispensing cleaning chemicals and agents e Step ladders for high level cleaning e Towels and rags ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to c
60. equired organisational advertising and promotional material as required e Spray clean and sanitise telephone s e Check and adjust clock s in the area to the correct time e Clean dust television screen clean television unit polish as required Set TV to nominated channel and volume setting Check batteries in and operation of remote control locate in nominated position replace batteries as required e Wipe clean light switches check operation of lights air conditioning fans Clean fixtures and fittings Fixtures and fittings may include e Picture frames around pictures in public spaces e Luggage carts used to transport customer guest luggage e Vases used for floral decorations and displays e Telephones e Stands on which items are positioned displayed e Trash receptacles the surrounds around the actual trash rubbish container the outer portion which makes the rubbish receptacle more visually appealing e Bollards e Vending machines What is required The aim of wiping and polishing fixtures fittings and accessories is to make sure they are free from dust stains and marks and to have them shine Regular day to day cleaning of accessories may include e Dusting always dust before vacuuming e Wiping with a damp cloth wetted with designated cleaning agent chemical or water e Working from top to bottom e Cleaning as required as opposed to cleaning everything ev
61. ers involves e Shake clean regularly in the appropriate location outside e Wash in accordance with the manufacturer s instructions ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Brooms and brushes Cleaning of brooms and brushes involves e Shake clean e Wash in hot soapy water e Air dry Cloths and sponges These should be e Cleaned on a regular basis using hot soapy water e Left to air dry Conducting safety checks Safety checks must be undertaken as part of cleaning items and storing them Activities include e Reporting problems issues identified during cleaning processes e Removing unsafe items from use e Following manufacturer s instructions regarding regular inspections and checks e Checking all attachments and cords Undertaking preventative maintenance and repairs Only basic maintenance and repairs will be required e Adding fuel to petrol and diesel driven units e Greasing and oiling parts e Emptying items e Changing filters and bags e Changing pads e Changing belts e Recharging batteries for battery powered units Maintenance requests Where further work needs to be done to equipment these situations must be reported Reports may need to be made verbally or in writing ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Storing
62. ery time use common sense to determine whether items needs to be wiped or polished e Spraying the item with designated cleaner from a spray bottle atomiser and wiping clean and dry with a cleaning cloth ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Only cleaning electrical appliances when they have been turned off and disconnected where possible ensure hands are dry before turning item off and disconnecting it only clean external surfaces Wiping and polishing items before the floor is cleaned washed Turning lights off before cleaning them never clean hot lights globes Replace blown globes at the same time if house policy Only stand on steps ladders not a chair from the lounge public area Re aligning pictures so they hang correctly Never spray directly on to pictures picture glass or picture frames as the chemical may drift on to the wall and over time discolour the wall surface Spray on to the cloth and then wipe the picture Using a sanitiser when wiping cleaning the handset of public telephones and internal in house phones paying special attention to the mouthpieces and allowing sufficient contact time according to manufacturer s instructions before removing the product e Also tidy the area around the telephone this may involve Straightening telephone books and note pads Replacing pens where pr
63. ever storing chemicals with foodstuffs beverages or containers which will be used to serve hold food or drinks Never storing chemicals in food containers Never eating drinking or smoking when handing storing chemicals Always washing hands after storing chemicals at the completion of cleaning Replenishing consumables Experience coupled with management guidelines relating to the levels of stock will assist in determining whether consumables need to be ordered An internal requisition is commonly used to order replacement materials from a central store Requisition forms completed and forwarded to the appropriate person at the end of shift today should result in the supplies ordered or requisitioned being supplied to the cleaning store later in the day or early the next day before the next shift starts work ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Work Projects It is a requirement of this Unit you complete Work Projects as advised by your Trainer You must submit documentation suitable evidence or other relevant proof of completion of the project to your Trainer by the agreed date 3 1 Provide video photographic real time or other acceptable evidence you have swept an area providing evidence you have e Assessed the area to be cleaned e Prepared the worksite job e Applied appropriate techniques e idied and returned the area to service e Cleaned checked
64. fferences and links between wet and dry cleaning and describes a range of techniques commonly applied Differences and links between dry and wet cleaning It is important to understand e Many dry cleaning techniques are pre requisites for wet cleaning techniques for example sweeping and dry mopping will often precede wet mopping e Dry cleaning involves techniques where there is little or no use application of water or liquids as part of the cleaning process it does not mean the approach is necessarily completely dry it means the liquid water used is not used to such as extent it is allowed to penetrate fabrics or surfaces it is used on e Dry cleaning techniques are basic and straight forward requiring fewer no chemicals and a simpler range of equipment e Dry cleaning techniques are often used more frequently than wet cleaning techniques e Dry cleaning can often be undertaken even where there are customers guests present because it is generally less intrusive requires less equipment and of shorter duration e Dry cleaning commonly requires less PPE often there is no need for any PPE e The same staff will be required to undertake both forms of cleaning e Customer guest safety and comfort must remain a priority when performing any cleaning General dry area procedures It is always necessary to treat every cleaning job on its merits the app
65. g Observation Checklist and Third Party Statement An observation checklist is a way of recording how you perform at work and a third party statement is a statement by a supervisor or employer about the degree of competence they believe you have achieved This can be based on observing your workplace performance inspecting your work or gaining feedback from fellow workers Your trainer and or assessor may use other methods to assess you such as e Journals e Oral presentations e Role plays e Log books e Group projects e Practical demonstrations Remember your trainer is there to help you succeed and become competent Please feel free to ask him or her for more explanation of what you have just read and of what is expected from you and best wishes for your future studies and future career in tourism and hospitality ASEAN 2015 Trainee Manual Clean premises and equipment Unit desoriptor descriptor Unit descriptor Clean premises and equipment This unit deals with the skills and knowledge required to Clean premises and equipment ina range of settings within the hotel and travel industries workplace context Unit Code D2 TTO CL4 03 Nominal Hours 25 hours Element 1 Prepare to clean Performance Criteria 1 1 Select the cleaning equipment to be used 1 2 Select the cleaning agents to be used 1 3 Select the protective clothing to be used 1 4 Check operation and safety of equipment that has been select
66. g maintenance by room or store name e Urgency associated with the request need for attention e Personal name and contact details e Date and time ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Storing equipment All equipment must be stored after cleaning and inspecting it Requirements include e Storing stowing in accordance with enterprise requirements e Locating all items in their designated places e Ensuring items are easy for the next person to access use e Making sure all attachments are stowed with the equipment e Completing any internal logs registers required Storing chemicals All chemicals must be stored after use in accordance with legislated requirements and enterprise requirements these may include e Left over chemicals in undiluted form must never be disposed of down a sink or a gully trap e Wearing appropriate PPE when storing chemicals e Returning chemicals to designated locations in the store e Storing chemicals with labels facing to the front e Checking each bottle container stored to ensure no leaks damage and lids seals are tight e Visually checking other chemicals and containers in the store at the same time e When spilt chemicals should be initially soaked up with sand earth or some kind of designated absorbent material e Leaving already de canted chemicals in spray bottles e Securing the chemical store to prevent u
67. ging batteries for battery powered units Maintenance requests Where further work needs to be done to equipment these situations must be reported Reports may need to be made verbally or in writing Most businesses will use a Maintenance Request Form which contains space to record e Type of maintenance issue such as pump not working filter requires replacement or plug needs re wiring e Location of item area requiring maintenance by room number office or other location e Urgency associated with the request need for attention e Personal name and contact details e Date and time Storing equipment e All equipment must be stored after cleaning Requirements include Storing chemicals All chemicals must be stored after use in accordance with legislated requirements and enterprise requirements these may include e Never disposing of left over chemicals in undiluted form down a sink or gully trap Chemicals should only be poured down drains fitted to chemical traps never assume a drain leads to a chemical trap e Local laws address may address environmental concerns requiring safe disposal of chemicals by requiring them to be Taken to designated collection sites Collected by specially licensed collection businesses e Wearing appropriate PPE when storing chemicals e Returning chemicals to designated locations as opposed to storing in random locations e Storing chemicals
68. hin the allocated time and or by a given time Cooperating with other employees to minimise interruption to their work Avoiding limiting annoyance to customers guests e Emptying ashtrays into designated containers e Be alert to smouldering butts which can cause a fire e Cleaning wiping and polishing ashtrays as required to optimise appearance this applies to free standing ash trays table based ashtrays and in vehicle ash trays e Remove and or replace table based ashtrays which are damaged e Picking up loose litter this means walking the area with a rubbish bag and physically picking up items which are lying on the floor or other surfaces in the area e Loose litter items may include Discarded items which have been used by a customer Newspapers Wrapping materials and food packaging Cigarette butts Soft drink containers e Picking up lost and found items the nature of what is determined to be lost and found items will vary between businesses but the following is indicative Personal clothing Personal items such as bags and wallets Personal papers and documents s All lost and found items must be processed according to house rules policies e Emptying rubbish containers important aspects are Do not overload rubbish bins or bags Be careful be alert to the potential for injury from broken glass and syringes ASEAN 2015 Trainee Manual Clean premise
69. ibe how they must be used The following two examples are taken from a Johnson Diversey Usage Chart Sparkle JFLEX Glass cleaner Taski R1 Plus Concentrated toilet cleaner Fill applicator bottle with Sparkle from the dispenser Apply Sparkle to clean cloth or directly onto mirror windows and any glass or chrome surface Polish off with lint free cloth Two doses in water filled bottle Flush toilet bowl or urinal Gently squeeze bottle directing jet under rim and around bowl Allow 10 minutes contact time Flush to rinse ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques 5 3 Prepare worksite Introduction Before cleaning ceilings surfaces and fittings commences the worksite must be suitably prepared This section introduces the concept of periodic cleaning and reinforces information from section 3 2 Periodic cleaning Not all aspects of every room area will need to be cleaned every day Some aspects are only cleaned on a periodic bases in addition to being undertaken when needed These cleaning tasks are often scheduled on a rotational basis and listed on an internal cleaning schedule Examples of periodic cleaning include e High level dusting such as Ceilings Tops of doors Fire sensors detectors Architraves Picture frames e Carpet cleaning as opposed to vacuum cleaning of carpets
70. ional materials give aways Re stocking of essential requisites soap toilet paper tissues towels Spraying room freshener deodorant e Inspecting the area this should be a visual inspection which may use a checklist to guide and record actions The inspection should Cover the entire area which has been cleaned ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques Note other issues which require attention this may be additional different cleaning as well as repairs maintenance Be undertaken in a structured manner such as inspecting from left to right or in a clockwise direction e Returning the area to operational status which may involve Unlocking doors which were locked during the preparation stage Locking doors which were unlocked as part of the cleaning process Turning equipment on or off as required lights heaters or coolers vending machines music systems Notifying supervisor cleaning has been completed and area is ready for service e Disposing of soil and waste this may require Collection of soil and waste Disposal into a bag or container bin Removal to an external bin container All disposal must comply with local environmental requirements which may necessitate Not disposing of soil waste into storm water drains Separation of nominated waste
71. is section addresses considerations in this respect Need for the checks Checking is important for a number of reasons e To avoid mixing chemicals from one item of equipment to another which may damage not only equipment but the surfaces the chemicals are being applied to e To avoid transferring dirt or grime from one surface to another it is a standard requirement all cleaning items must themselves be cleaned e To stop transportation of bacteria from one surface to another the cleaning items such as mops used in food areas will not only need to be washed but will also need to be sanitised as well e To avoid accident and injury arising from the use of unsafe equipment Conducting checks Overview The checks will depend on the item being checked Manufacturer s instructions and User Manuals Operator Books for equipment will provide the basis for the checks which need to be made of individual items The checks outlined below must be done every time an item of equipment is selected for use without exception The checking process The checking process must focus on e Communicating with other staff to learn about problems with items and to identify equipment which is Out Of Service e Being alert to tags on machines which have been attached because the item has been assessed as dangerous and has been taken Out Of Service e Reading internal Communication Books which advise of machine equipment problem
72. l assist in determining whether consumables need to be ordered When requesting supplies a requisition form may have to be completed The requisition form is an internal stock ordering form and will identify Person requesting the items ltems needed by type and brand name Quantity of units required Size of each unit container Date Requisition forms completed and forwarded to the appropriate person at the end of shift today should result in the supplies ordered or requisitioned being supplied to the cleaning store later in the day or early the next day before the next shift starts work ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques Work Projects It is a requirement of this Unit you complete Work Projects as advised by your Trainer You must submit documentation suitable evidence or other relevant proof of completion of the project to your Trainer by the agreed date 2 1 Provide video photographic real time or other acceptable evidence you have wet mopped an area providing evidence you have e Assessed the area to be cleaned e Prepared the worksite job e Applied appropriate techniques e Tidied and returned the area to service e Cleaned checked and stored the equipment which was used 2 2 Provide video photographic real time or other acceptable evidence you have used a wet vacuum cleaner addressing all the following poin
73. large S shaped strokes Do not stand in mopped area Rinse the mop head frequently and re load as described above Change water and detergent regularly use common sense and visual appraisal to determine when this is necessary adhere to all safety precautions Complete job After activity During shift e Return dust mop to trolley After activity End of shift Clean dust mop in store room dust mask must be worn Wash and sanitise wet mop in sink outside store room Brush out and shake mop head use bristle brush Inspect and replace heads where necessary Return mops to cleaning store hang on hook with head away from wall Wash hands when finished ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques Richtee Cleaning toilets and urinals The cleaning of toilets and urinals is a common wet area cleaning task The following gives direction as to how it may be undertaken Prepared by Date Step Prepare the area Prepare equipment and materials Clean the toilet and urinal ASEAN 2015 Trainee Manual SOP Cleaning Toilets and Urinals Hazard Type and Rating Physical slips and trips Low Chemical Low Chemical and Physical Medium Clean premises and equipment Actions precautions required e Set up Cleaning in progress Do Not Use signs place tape across main entry door e Turn exhaust fans on and l
74. lean to clean 1 2 Select the cleaning agents to be used Introduction As well as selecting the correct cleaning items equipment for the job there is also a need to select the appropriate cleaning agents This section identifies the range of cleaning agents available and gives an overview of their use General information Chemicals may be provided in e Liquid form used for most detergents cleaners sanitisers and disinfectants e Powder form some detergents come in this dry form e Aerosol form many pesticides and deodorisers are supplied in this way e Paste form commonly used for polishes Liquid chemicals may be e Provided in small plastic bottles containers say 500mlis e Supplied in bulk say 20 25 litres and hooked up to a sealed system where product is de canted into smaller containers such as spray bottles Business may elect to use e Products bought commonly at the supermarket and intended for domestic use e Commercial or industrial chemicals which are usually stronger they have more and or different active ingredients and are far cheaper Where a full clean of an area carpet fabric wall upholstery is not required spot cleaning may be applied using a spotter spot cleaning agent or simply wiping the affected area Cleaning chemicals Cleaning agents may include Detergents Detergents are chemical based and can vary in strength so it is impo
75. lowed or makes contact with eyes or skin Work in ventilated conditions when using chemicals Avoid contact between food items and chemicals Always wear use the personal protective clothing or equipment provided by the employer when dealing with chemicals see Section 1 3 Do not handle chemicals until appropriate training has been provided either from a supervisor an experienced staff member or a representative from the company that supplies the chemicals Only use the designated items to measure weigh chemicals to be used never use jugs or containers that could then be inadvertently used elsewhere in the property for food preparation service purposes Treat the handling of chemicals with the seriousness it deserves focus on the chemical handling task at hand do not become distracted no skylarking Some chemicals are flammable so keep all chemicals away from heat or a naked flame Wash hands after using chemicals and after all cleaning duties to remove chemicals residue this applies even when wearing protective gloves See also A step by step guide for managing chemicals in the workplace at https www worksafe vic gov au _data assets pdf_file 0018 60075 Managing chemicals in Workplace pdf ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean 1 3 Select the protective clothing to be used Introduction Use of cleaning chemicals and or cleaning equipment often means there
76. m the surface Spirit based polishes are generally used for metal surfaces as well as windows and mirrors Oil based polishes are generally used for leather wood synthetic flooring linoleum and tiles Surfaces can be slippery after they have been polished so polish should be used with this in mind Abrasives Abrasive cleaning agents are available in powder cream or paste forms They are used for scouring and cleaning ceramic or enamel surfaces An example of such a surface is the toilet bowl or the shower basin abrasive cleaners must not be used on surfaces that scratch easily Abrasives can be hard to rinse away so it is important to wipe and rinse as soon as possible after application if they are left to dry abrasives can be much harder to rinse and clean away and may leave behind a harmful residue Other chemicals Depending on the job to be done the following may be required Disinfectants These Are cleaning agents which destroy disease carrying micro organisms Should be diluted according to manufacturer s instructions if it is diluted too much the disinfectant will become ineffective Have a strong scent and so are not suitable for use in a kitchen or any food area Should be used only in the toilet bathroom and change areas Deodorisers Deodorisers are used to mask or eliminate unpleasant smells They are commonly in aerosol form and should sprayed sparingly to achieve their aim but
77. ment Apply dry area cleaning techniques dry area cleaning techniques 3 2 Prepare worksite Introduction Before dry cleaning commences the worksite must be suitably prepared This section reproduces information contained in Prepare worksite from section 2 2 Preparation activities prior to moving to the work area Before arriving at the worksite there may will be a need to e Obtain work order from supervisor e Load cleaning trolley On arrival at work area The following activities are standard before cleaning begins e Notifying required persons cleaning is about to start e Emptying ashtrays e Cleaning wiping and polishing ashtrays as required to optimise appearance e Picking up loose litter e Picking up lost and found items e Emptying rubbish containers e Erecting appropriate warning signs in the location being cleaned e Moving and removing furniture and fittings as required e Moving a vehicle which has to be cleaned to a safe location or designated cleaning washing bay e Understanding organisation specific directions instructions applicable to the job e Putting on and or using necessary PPE and clothing for the job to be done ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques 3 3 Clean dry areas Introduction The use of dry cleaning is the most widespread type of cleaning used in businesses This section discusses di
78. ming final touch ups e Finalising the job such as placement of products re stocking of essential requisites soraying room freshener deodorant e Inspecting the area e Returning the area to operational status e Disposing of soil and waste e Returning vehicles to designated locations e Recording completion of cleaning e Dealing with lost and found items ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques 5 6 Clean check and store equipment and chemicals Introduction Following completion of cleaning tasks the standard need to clean check and store equipment and chemicals remains Generally speaking less cleaning of equipment and fewer checks are required following dry cleaning This section highlights previously presented information in this regard Cleaning the equipment used Cleaning locations Cleaning of items may be undertaken e Inthe cleaning store room e In a designated cleaning room e n nominated outside locations Need to clean items Equipment needs to be cleaned after use so as to e Prevent odour problems e Maintain a high level of appearance e Maximise operational effectiveness e Leave the items ready for use next time they are needed Mops Dusting mops After use e Shake thoroughly in appropriate location outside e Wash in hot soapy water e Hang out to air dry Dusters Cleaning of dust
79. n performing wet area cleaning Wet areas defined Wet areas are e Areas where there is normally liquid or water present toilets bathrooms shower areas pool sides e Most outside areas which are open to the weather e Areas which can be cleaned using wet cleaning techniques especially wet mopping General wet area procedures It is always necessary to treat every cleaning job on its merits that is the approach to cleaning and the techniques equipment and chemicals used must always reflect the circumstances and individual nature of the job This said cleaning wet areas may include e Removing loose dust this is a basic first step Picking up loose rubbish litter and debris Sweeping the area Dry dust mopping the area e Treating heavy soil which may mean Using spot cleaning chemicals and techniques Scraping away built up material e Treating graffiti this may require Use of nominated graffiti wipes paint removers gels or solvents Surface restoration such as painting Pressure washing see Element 4 Application of anti graffiti coatings Engagement of professional cleaning company specialising in graffiti removal e Mopping in terms of Dry mopping to remove loose dust and debris Wet mopping see below to clean the area ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning te
80. n smooth but firm strokes on open surfaces and straight stokes against walls Rinse mop and repeat until finished Empty bucket into gully trap and rinse mop and bucket Fill mop bucket with warm water Add 250 mls XYZ disinfectant use yellow measuring jug Apply as above Allow to dry set up Wet floors signs where appropriate Return moved items Remove and dispose of rubbish picked up during preparation external dumper Wash mop and bucket Dispose of protective gloves Return equipment and chemicals to storage Wash hands Apply wet area cleaning techniques wet area cleaning techniques Work Instruction Number 22 Wet Mopping Prior to Work Erect wet floor cones in area to be mopped Remove loose rubbish and debris use dust pan and brush and wear protective gaunitlets and dust mask Use scraper to remove gum and other material where necessary Remove furniture and obstacles from area to be mopped Take correct size clean dust mop and wet mop to area to be mopped Fill mop bucket with water at temperature of 20 and add ABC mils of XYZ detergent to water wear safety goggles when handling detergent Activity Wet mopping Dust mop the area before starting to wet mop see Work Instruction 21 see section 3 3 Commence wet mopping Immerse mop in mop bucket Wring out until mop is damp not wet dripping Mop area against skirting boards first Next mop surface area using
81. n for other cleaning because of the presence of water under pressure which will be part of cleaning process Certain wet or dry cleaning may be able to be undertaken when customers are present in the area but this is generally not the case when pressure washing This usually means pressure washing is undertaken e When the business is closed e When areas requiring cleaning are closed to the public Other preparations Before starting pressure washing the following may be required e Secure the area so members of the public cannot gain access Close and lock doors and gates Erect safety chains and barricades e Put necessary signage in place such as Wet surfaces Cleaning in Progress Do Not Enter e Pre clean the area to be washed by Picking up loose litter Spot cleaning obvious problem areas e Physically check the area to ensure No members of the public are present Any items requiring attention are suitably addressed which may necessitate Covering protecting items Putting items away or re locating them for the duration of the cleaning process so they do not get wet damaged Turning certain electrical items off e Talking to statt supervisors in the area to be cleaned to Obtain approval to proceed Determine special cleaning requirements Identify necessary cleaning parameters when area needs to be returned to service e Dete
82. n to keeping the outlet free of debris e Dry the tank e Remove debris from air cooling vents e Clean exterior of machine including operator controls Conducting safety checks Safety checks must be undertaken on all equipment as part of cleaning items and storing them Activities include e Reporting problems issues identified during cleaning processes e Removing unsafe items from use e Following manufacturer s instructions regarding regular inspections and checks e Checking all attachments and cords Undertaking preventative maintenance and repairs Only basic maintenance and repairs will be needed as other maintenance and service must be performed by suitable qualified technicians What is classified as basic maintenance and repairs can vary between businesses and vary with the make model and type of pressure washer e Adding fuel to petrol and diesel driven units e Adding oil e Greasing and oiling parts e Replacing user serviceable parts as where appropriate depending on make model and type for example spark plugs air filter Maintenance requests Maintenance reports requests may need to be made verbally or in writing Most businesses will use a standard Maintenance Request Form to record e Type of maintenance issue such as pump not working filter requires replacement plug needs re wiring leak from crankcase insufficient pressure e Location of the unit requirin
83. nauthorised use of the chemicals e Disposing of any chemicals which have been diluted e Never storing chemicals with foodstuffs beverages or containers which will be used to serve hold food or drinks e Never storing chemicals in food containers e Never eat drink or smoke when handing storing chemicals e Always wash hands after storing chemicals at the completion of cleaning Replenishing consumables Experience coupled with management guidelines relating to the levels of stock will assist in determining whether consumables need to be ordered An internal requisition is commonly used to order replacement materials from a central store Requisition forms completed and forwarded to the appropriate person at the end of shift today should result in the supplies ordered or requisitioned being supplied to the cleaning store later in the day or early the next day before the next shift starts work ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Work Projects It is a requirement of this Unit you complete Work Projects as advised by your Trainer You must submit documentation suitable evidence or other relevant proof of completion of the project to your Trainer by the agreed date 4 1 Provide video photographic real time or other acceptable evidence you have used a pressure washer to clean an area providing evidence you have e Assessed the area to be cleaned e Prepared the w
84. ng Ensure mop is appropriate size for area to be mopped Start at one end far end of area to be mopped amp work towards door exit Hold mop at angle of approx 45 while mopping for ergonomics and efficiency Mop the hard surface Frequently shake the mop to remove unload dust over un mopped area or outside Walk with mop in front for one complete pass section of floor Turn at the end of a pass and mop in the opposite direction for another pass section of the floor ensuring each pass overlaps approx 4 5cms After activity During shift e Return dust mop to trolley After activity End of shift Clean dust mop in store room dust mask must be worn Brush out and shake mop head use bristle brush Inspect and replace head where necessary Return dust mop to cleaning store hang on hook with head away from wall Wash hands when finished ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Vacuuming Dry vacuum cleaning is generally not undertaken in exterior outside areas General vacuuming protocols When vacuuming carpets and floors Vacuuming should occur after dusting and other cleaning has been finished vacuuming is one of the last jobs to do Before starting to vacuum a floor carpet walk over it and pick up any items likely to cause damage to the machine or block the vacuum hose these items may be relatively large pieces of paper pins b
85. ny damage can be noted reported before starting e Inspect vehicles to be cleaned to check them for pre existing damage level of interior and exterior dirt and any service related issues which may need to be reported so appropriate maintenance can be provided e Factor in weather conditions should Planned cleaning be delayed until the weather changes improves Special requirements apply because of the weather at the time e Determine Start and finish points for the job Location of cleaning equipment and resources during the job ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques 2 2 Prepare worksite Introduction It is important to prepare worksites for cleaning before commencing actual cleaning duties This section identifies activities in preparing worksites for cleaning and presents considerations for interacting with customers guests as part of cleaning activities Preparation activities prior to moving to the work area Before arriving at the worksite there may will need to e Obtain work order from supervisor not all cleaning jobs will require a work order but some businesses use them to organise and allocate work to statf Work orders will indicate The areas locations to be cleaned serviced Sequence of work to ensure work is completed in priority order and finished when required Special jobs such as indication where fo
86. o the job Putting on and or using necessary PPE and clothing for the job to be done ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques 5 4 Clean ceilings surfaces and fittings Introduction When the work to be done has been assessed and the required equipment and chemicals have been selected cleaning can begin This section talks about efficient work highlights several important safety aspects and presents cleaning directions for a range of ceilings surfaces and fittings Working efficiently Efficient work demands Proper training this is key to ensuring work can be performed in the way required by the organisation and produce an end product meeting required standards Use of the correct items and chemicals for each job as identified by the training Adherence to a nominated sequence for completing each job every job can be most efficiently completed by following an established order of work which has emerged at each business over time based on the individual layout of areas spaces standards required and equipment available used Focus on the job to be done cleaners need to move quickly and not dawdle there is an ongoing need to concentrate on the work which has to be completed Techniques to assist with efficient work The following strategies have emerged to assist cleaners work most efficiently Move through a
87. orksite job e Applied appropriate techniques e idied and returned the area to service e Cleaned checked and stored the equipment which was used ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Summary Apply pressure washing techniques When applying pressure washing techniques Assess the job and work to be done Plan the work Prepare the job worksite and ensure no members of the public are present Wear use designated PPE Be aware of the dangers inherent in using pressure washers Never point the spray jet at anyone no skylarking Obtain training and supervised practice Follow SOPs WIls and manufacturer s instructions Fit the correct nozzle for the work to be done Check connections before using the machine Take care not to damage surfaces onto which the spray jet is applied Avoid pressure washing already damaged surfaces Tidy worksite before returning it to service Clean check and store cleaning equipment and PPE after completion of task s Take action to replace replenish used items ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Element 5 Apply ceilings surfaces and fittings cleaning techniques 5 1 Assess ceilings surfaces and fittings to be cleaned Int
88. ospens olo Element 3 Apply dry area cleaning techniques as aa a mj FO lemme o oo joa teywonste s ofo s oran oresana sors savmono o o ASEAN 2015 Trainee Manual Clean premises and equipment Traine sel assssment checkit self assessment checklist Element 4 Apply pressure washing techniques Assess area to be pressure washed Prepare worksite Clean areas using pressure washer Tidy worksite 4 5 Clean check and store equipment and chemicals e Element 5 Apply ceilings surfaces and fittings cleaning techniques Assess ceilings surfaces and fittings to be cleaned Select appropriate equipment and chemicals Prepare worksite Clean ceilings surfaces and fittings Tidy worksite 5 6 Clean check and store equipment and chemicals Statement by Trainee believe am ready to be assessed on the following as indicated above Signed Date Note For all boxes where a No is ticked please provide details of the extra steps or work you need to do to become ready for assessment ASEAN 2015 Trainee Manual Clean premises and equipment Australian Aid P Wiliamg Specialist centre Angliss for foods tourism amp hospitality Institute
89. ottle toos Use common sense about what the vacuum cleaner can effectively pick up and what it cannot Use the appropriate cleaning tool for the surface to be cleaned vacuumed see the User Operator manual for more detail different machines have different tools for different carpet types and different surface types so a machine may feature A single head a variable head which can be adjusted for different surfaces bristles down for hard surfaces bristles retracted for carpets rugs One head which may be suitable for all surfaces Crevice tools nozzles for reaching hard to reach clean areas corners of rooms and furniture Extensions to the handle to give the machine extra length reach for cleaning high areas Start vacuuming from the farthest point from the door and work backwards towards the door Use smooth movements overlap each stroke work backwards and forwards moving towards the door of the room lf required to clean vacuum a set of stairs start at the top and work towards the bottom If the vacuum cleaner has a long electrical cord hold the cord or place it over the shoulder to help avoid running over it Use the vacuum cleaner with care this means making a conscious effort to make sure the head or the machine itself does not hit walls furniture fixtures and fittings Empty the vacuum cleaner or bag on a regular basis the fuller the bag cleaner the less effectively it works
90. ovided necessary Removing litter Emptying rubbish bins paying special attention to those which may contain cigarette butts to prevent ignition of other materials all bins where there is the potential for cigarette butts including ashtrays must be emptied into a metal container not a plastic one and not into a plastic garbage bag This process may also require Replacing bin bags Cleaning wiping and or polishing external surfaces Replacing bins to their designated locations Cleaning bollards these are often used in public areas to fence off an area or direct foot traffic Bollards are often made from metal and cleaning them on a day to day basis may involve Polishing cleaning individual bollards Adjusting the ropes chains between the bollards to present a standard appearance between bollards Moving bollards as instructed by management to meet identified or emerging need Removing bollards and ropes to the storage area where they are no longer needed Re locating the bollards and rope to an area where they are needed Making sure all fixtures and accessories look clean do a final visual check and clean re clean as or if needed ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques High dusting High dusting involves e Concentrating on architraves air conditioning vents corners window frames window
91. ques Impart expertise based on their knowledge and experience e Provision of safe equipment which is regularly serviced and maintained and certified safe to operate ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Practical operational advice Important points When pressure washing Always follow internal protocols which include Wls and SOPs Techniques shown in training Normal ways of doing things Manufacturer instructions and warnings Always use common sense be alert to unique situations which make it necessary to vary normal standard approaches to accommodate a different set of factors Do not play with the equipment pressure washers are not toys Never point the jet at anyone Do not direct strong streams towards glass doors or windows Be careful of directing a concentrated stream in the one place for too long as the jet can cause damage Stay focused concentrate on the work to be done Maintain situational awareness pay attention to surroundings Never use a pressure washer when standing on a ladder seek an alternative cleaning solution When using an electrically operated machine pay special attention to ensuring the power cord is controlled so it is kept out of standing water to reduce the potential for electric shock electrocution e Standard practice is to ensure these machines are connected only to power
92. quired but there are differences between models and makes e Remove bag if unit is a wet dry machine e Connect required attachments as appropriate for the job e Select appropriate wet function e Commence soaking sucking up the liquid e Move unit using the handle and not by pulling on the vacuum hose e Keep the electrical cord out of water e Monitor capacity of vacuum tank to ensure it does not over fill unit to drainage area when tank is full and or when job is finished to drain the tank Online videos The following provide demonstrations on wet cleaning techniques http Awww youtube com watch v MgN_ rsWOtCl Floor Tech Wet Mopping 4 mins 34 secs http Awww youtube com watch v 3eFOwWhKP6EY How to damp mop floors 3 mins 54 secs http www youtube com watch v KI9X07UGyu0 How to mop 3 mins 9 secs http www youtube com watch v RJo8HZhHNCY How to clean a commercial restroom 21 mins 4 secs http Awww youtube com watch v r3vGCUaimsw Restroom cleaning simple techniques 10 mins 50 secs http www youtube com watch v f CWhrgGis8 Washroom cleaning training video 8 mins 3 secs ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques 2 4 Tidy worksite Introduction After cleaning has been completed there is a need to return the area or vehicle to service This section lists the basic activities in this phase of the job Finishing
93. r example special cleaning or action is required e Load cleaning cart trolley not all businesses will use a cleaning trolley but they are a useful way of moving cleaning requisites and keeping them handy e Where they are used they may need to be loaded stocked with Tools and equipment to undertake the allocated job Caddies and baskets to hold items which need to be carried into an area the cleaning trolley will not be able to be taken into all areas where cleaning has to be performed because it may be too large or it may create an unacceptable obstacle Cleaning chemicals and agents Personal protective equipment and clothing Replacement items needed to re stock re supply the area being serviced or cleaned Items may include Soap and towels Ashtrays Toilet paper Light globes Promotional materials ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques On arrival at work area When arriving at a location to be cleaned the following activities are standard before cleaning begins e Notifying required persons in the area cleaning is about to start e These persons may include Area supervisor Staff in the area Customers guests Many cleaning tasks which have to be completed are often a balancing act needing to balance Getting the job done as Completing the task wit
94. re clean the floor first pick up loose litter and sweep e Fit correct polishing pad e Adjust handle of machine to correct height for individual operator this is a comfortable position which gives control over the unit waist thigh height is recommended e Place electric cord over the shoulder to keep it out of the way danger e Control the direction of the machine using raising and lowering techniques this means using the rotation of the pad to direct the way the machine moves Gently raising the handle to send the machine to the right Gently lowering the handle to send the machine to the left The only way to gain competence in operating these machines is experience practice expect loss of control to begin with so practice in areas free from objects which may be damaged by accidental contact impact Check the following video for further information http www youtube com watch v 6pNSaWtR9fs Floor Buffer Demonstration 3 minutes ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques dry area cleaning techniques 3 4 Tidy worksite Introduction When dry cleaning has been completed the work area will need to be tidied and returned to service This section reinforces information contained in section 2 4 Finishing activities The exact nature of finishing activities required will depend on the preparation activities
95. rmine work flow in terms of Start point Progress through job Finishing point Water flow to waste ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques Obtain pressure washing machine and other requisites depending on the job area to be cleaned there may be a need to obtain Broom Wet mop Squeegee Nozzles Wands spray guns lances Hose and reels Rotary floor surface cleaners Cleaning of vehicles may also require obtaining Polish Rags cloths Detailing kits gear Obtain chemicals taking into account Type of dirt to be cleaned refer Chemical Usage Chart as provided by chemical supplier Sufficient quantity based on estimation of requirements for the job Organisational Work Instructions or directions SOPs Obtain necessary PPE which must include water proof garments and boots as well as safety goggles protective eye wear set the machine up connect as required Water Chemicals Hose Gun and nozzle Position the unit and allow for free travel movement of machine to the best extent possible to enable the required cleaning to be completed ASEAN 2015 Trainee Manual Clean premises and equipment Apply pressure washing techniques pressure washing techniques 4 3 Clean areas using pressure washer Introduction The operation of a pressure washer requires concentration and competency
96. roach to cleaning and the techniques equipment and chemicals used must always reflect the circumstances and nature of the job This said dry cleaning includes e Dusting and polishing e Dry mopping e Vacuum cleaning e Sweeping e Floor polishing ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques dry area cleaning techniques Dusting and polishing The main purpose of dusting is to collect small particles of dust The main purpose of polishing is to clean the item and leave a shiny reflecting finish Dusting may be done with a duster or a damp lint free cloth It is important to use common sense when choosing which cloth article to dust with do not use a damp cloth if the moisture could ruin the object being cleaned and remember to change the cloth when soiled On the job training which will probably include being teamed up with an experienced room attendant for a couple of days will provide guidance in this regard When polishing an item make sure to Spray the cleaning agent onto the cloth not onto the surface to be cleaned Buff the surface after cleaning to remove any streaks When dusting and polishing a room it is best to start in one spot and work around the room say in a clockwise direction this routine should be followed in every room Some small items may need to be picked up in order to dust or polish underneath The following ar
97. roduction The need to assess the work to be done extends to the cleaning of ceilings surfaces and fittings This section provides detail of the generic activities required Assessing the work to be done The keys to identifying work to be done include e Visiting and inspecting the areas to identify work needing to be done on the basis of personal experience and enterprise knowledge regarding standards of cleanliness and presentation e Following programmed cleaning schedules which dictate the frequency with which items areas must be cleaned e Talking to other people who may include customers staff and supervisors Types of ceilings Ceiling types which may require cleaning can include e Flat ceilings the standard level horizontal ceiling common to the majority of rooms e Suspended ceilings common in many locations where a space is created between the ceiling and the floor above it from which it is suspended hung e The space may allow a lower ceiling to give ambience or provide a space for cabling wiring and similar e Raked ceilings an interior ceiling which angled usually reflecting the angle of the exterior roof e Vehicles such as the inside of a bus coach four wheel drive or sedan ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Types of surfaces e Surface types to be cleaned may be e P
98. rt soil needs to be removed Is ita big area or a small space Are there any obvious problems difficulties with the job e Work out how long the job will take in order to Plan other work Integrate this job with other work to be done Arrange for other staff to assist if necessary e Allow discussion with relevant others in relation to the job this can mean speaking with area supervisors to ascertain their particular requirements Are there are things they want concentrated on Are there areas which need to done first or finished by a certain time ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques Are there problems dangers they need to communicate e Gauge level of customer traffic usage to determine Should cleaning be delayed until a quieter later time Barriers and warning signs which need to be put in place e Determine complexity of the job to work out If help with the work is required f specialist equipment or techniques are required e Identify most appropriate and effective cleaning techniques to apply to clean the area as required which will be a prime determinant of the resources required e Work out the resources required in terms of Cleaning equipment and ancillary items Cleaning chemicals and agents e Check condition of equipment in and condition of area to be cleaned so a
99. rtant to follow the correct dilution instructions when using this type of cleaning agent Detergents have different pH scales and it is the pH level of the detergent that informs the user of the type of surface it is best used on General purpose detergents General purpose detergents are used in every business and as their name indicates can be used on a wide variety of surfaces and for a range of cleaning tasks A pH of 7 is a neutral pH level and these types of detergents are useful for general cleaning ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to lean to clean Acidic detergents Acidic detergents graded as having a pH of 1 to 6 should be used for cleaning ceramic surfaces Alkaline detergents Alkaline detergents graded as having a pH of 8 to 14 should be used only for specialist tasks as they can be corrosive and have the ability to damage a surface High alkaline detergents should be used only as directed and only on surfaces they were designed to clean The surface they are used to clean should also be rinsed thoroughly to remove any harmful residue Remember high alkaline detergents can be harmful to the skin they should be treated with care Spillage should be avoided at all times protective clothing should be worn when using high alkaline detergents Specialist detergents Cleaning chemicals have been developed to address specific cleaning tasks check what is available in
100. rubbish Recycling of items Control of odours and vermin Regular cleaning of waste bins containers e Returning vehicles to designated locations which may require Completion of vehicle log Locking doors of vehicle Hand over of keys to designated person supervisor Parking in a specific manner such as reverse park or nose in e Recording completion of cleaning this may require Filling in a work schedule to record work completed at the end of the shift Compete an area specific time sheet indicating When the area was cleaned serviced Who did the cleaning servicing e Dealing with lost and found items this may require Handing found items in to the designated lost and found area facility Completing a lost and found entry in the Lost and Found Register or providing relevant details so such an entry can be made addressing Description of the item Where it was found When it was found ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques 2 5 Clean check and store equipment and chemicals Introduction The final tasks when finishing a cleaning job are the cleaning checking and storing of equipment and chemicals which were used This section identifies activities and issues involved Cleaning the equipment used Individual businesses may have SOPs to guide the cleaning of equipment which has been used The following is in
101. s ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Element 3 Apply dry area cleaning techniques 3 1 Assess areas to be cleaned Introduction In the same way areas to be wet cleaned need to be assessed prior to cleaning so too do areas which will be cleaned using dry cleaning techniques This section discusses the assessment stage of a cleaning job and reproduces much of the information presented in section2 1 Assessing the job Overview of the process Assessment of the task is part of planning and preparation for the job and involves e Looking at the area job visually inspecting the area e Talking to people who have input to make or responsibility for the area e Using knowledge and experience as key reference points Specifics of each job When assessing the task area e Determine the extent of the work to be done e Work out how long the job will take e Allow discussion with relevant others in relation to the job e Gauge level of customer traffic usage e Determine complexity of the job e Identify most appropriate and effective cleaning techniques to apply to clean the area as required e Work out the resources required e Check condition of equipment in and condition of area to be cleaned e Inspect vehicles to be cleaned e Factor in weather conditions e Plan the job ASEAN 2015 Trainee Manual Clean premises and equip
102. s and equipment Apply wet area cleaning techniques Clean polish bins after they have been emptied as appropriate Re fit bins with bin liners according to standard house practices e Erecting appropriate warning signs in the location being cleaned these may include Wet floor signs cones Cleaning in progress signs cones These signs should be placed in plain view of customers guests which may mean they are positioned Near entrances doors Near lifts elevators In some cases there may be a requirement to close the area so no one can enter while working this may mean closing and locking doors or erecting physical barricades tape e Moving and removing furniture and fittings as required so Easier access to other areas items is obtained Damage to them as a result of cleaning is avoided Sometimes there will be a need to cover equipment stock facilities and items with protective material and or drop cloths to avoid contact from water and or cleaning agents dust or other contamination Liza Ji e Moving a vehicle which has to be cleaned to a safe location or designated cleaning washing bay This may be needed to Enable easier access to specialist vehicle cleaning tools and materials Avoid obstruction to other vehicles and customers guests Prevent drift to others when washing the exterior of the vehicle e Understanding organisation specific dir
103. s and or unavailability e Being advised by supervisors at staff briefings e Visually inspecting items and Looking for problems and worn parts Checking all parts components are in place and looking normal ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean Turning equipment on where appropriate to conduct test runs Listening to mechanical and electrical equipment to determine lf there any unusual noises indicating a problem such as grinding noises sparking loose components Whether equipment is working as expected anticipated Looking to detect problems Smoke or sparks Vacuum bags which may not inflate Using sense of touch to determine lf there are unusual or unacceptable vibrations f unusual or unacceptable heat is being generated Using sense of smell to determine Smoke Burning electrical or rubber odour Examples of basic checks The following is indicative of checks to be made Equipment does not have any jagged parts or sharp edges which can cause injury Damage normal wear and tear to equipment has not affected its operational safety Check and clean the exterior of cleaning equipment to enhance presentation and project a positive image for the company when seen by patrons cleaning equipment must be clean Ensure mop head looks presentable customers will be able to see these when working in public areas an
104. s may be damp or wet after being shampooed or steamed so this needs to be taken into consideration before cleaning high traffic areas both in terms of how the area will look and smell and from a safety viewpoint All carpet shampoo machines must be used in accordance with the manufacturer s instructions Companies selling vacuum cleaners usually also supply carpet shampooers so check out the sites for vacuum cleaners listed above as well as http www cleantreak com www machines4u com au www cleancare com au ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean Polishers Polishing a floor helps resist scratching and enhances appearance Polishers may be e Buffers these are low speed machines the pads revolve at relatively low speeds suitable for multiple purposes such as stripping a floor scrubbing and low speed polishing e Burnishers these are high speed machines pads revolve at relatively high speeds and they are used to provide the high gloss finishes to vinyl floors See examples at www totalsupplysolutions com au cleaning www pacvac com commercial floor polisher Pads Polishers will use different pads depending on the type of job being done and the weight and speed of the machine Each manufacturer can have their own colour coding system for pads so check with the manufacturer to see what applies As an indicator e Black pads and green pads ma
105. se should be fully operational not leaking easy to operate and not smelly Buckets may be required for wet mopping Protective gloves a good supply of disposable gloves should be on each cart trolley specific house requirements in relation to workplace health safety and welfare issues may require other more substantial protective clothing including gloves be worn Cloths used for cleaning polishing and dusting every cart trolley will need to have lots of these Some are made from material and some are disposable paper based Ancillary items such as door stops extension cords scouring pads sponges and step ladders Warning signs these are safety signs used when a public area lobby public toilets is being cleaned as part of the overall preparation process Rubbish bag for stowing rubbish collected this may be built into one end of the cart trolley Linen bag a cloth or calico bag for placing dirty used linen into this too may be built into the other end of the cart trolley Clean linen and towels as if required for the area s to be cleaned serviced Replacement replenishment items such as toilet amenities stationery advertising materials give away items light globes ash trays rubbish bags bin liners Chemicals which may be required Chemicals which may be needed may include Cleaning agents and other chemicals to perform various tasks and clean various surfaces
106. sh hands Cleaning mirrors and glass surfaces Steps may include e Wetting mirror or glass surface with damp sponge dipped in hot water to remove any obvious marks e Spraying with mirror glass cleaner cleaning with clean damp sponge this step may need to be repeated depending on condition dirt e Using razor with safety handle to remove hard spots e Using squeegee to remove excess water use overlapping strokes and wipe rubber blade clean dry at end of each stroke e Drying off with cloth or paper towel e Inspecting checking work and remedy problems smudges and watermarks as identified e Noting damage to mirrors and glass cracks need for re silvering rust stains and reporting to supervisor area manager or duty manager ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning techniques Using wet vacuum cleaner Wet vacuum cleaners are used to clean up liquid water spills or flooded areas on hard or soft floor surfaces Only vacuum cleaners designated as wet machines can be used for this work there may be a requirement to use a dedicated wet only machine or a wet dry unit which can be switched between dry and wet vacuuming When using these machines follow the directions contained in the User Manual Operating Instructions for the individual device being used the following is indicative of what may be re
107. sportation regulations Safe handling procedures e First aid Suppliers of chemicals are obliged to provide MSDS for all chemicals purchased from them See the following for more information http Awww msds com au httos www worksafe vic gov au safety and prevention health and safety topics material safety data sheets ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean to clean General rules for dealing with chemicals It is important to adhere to the following when handling using chemicals Always follow the manufacturer s instructions this the Golden Rule when handling using or otherwise dealing with chemicals or cleaning agents Never mix chemicals together doing this can cause them to be ineffective can cause them to give off toxic fumes and can cause them to explode Read the labels for all products Never apply chemicals directly to the surface unless the directions specifically recommend advise this Dilute chemicals according to manufacturer s instructions most chemicals will require some degree of dilution Contact the supplier or supervisor if unsure about any aspect of using or dealing with any chemical Never store chemicals with food it is illegal to do so Avoid contact between bare skin eyes mouth and any chemical this applies to direct contact as well as indirect contact Follow the specific advice on the relevant MSDS if chemical is swal
108. sure that this publication is free from errors or omissions However you should conduct your own enquiries and seek professional advice before relying on any fact statement or matter contained in this book The ASEAN Secretariat and William Angliss Institute of TAFE are not responsible for any injury loss or damage as a result of material included or omitted from this course Information in this module is current at the time of publication Time of publication is indicated in the date stamp at the bottom of each page Some images appearing in this resource have been purchased from stock photography suppliers Shutterstock and iStockphoto and other third party copyright owners and as such are non transferable and non exclusive Clip arts font images and illustrations used are from the Microsoft Office Clip Art and Media Library Some images have been provided by and are the property of William Angliss Institute Additional images have been sourced from Flickr and SXC and are used under Creative Commons licence http creativecommons org licenses by 2 0 deed en File name TM_Clean premises and equipment_280115 Australian nal is Specialist centre Aid gt Ang gliss amp NO spitalty Table of contents Introduction to trainee MANU AN ssccisht cncuseesncvuebszcecadrarancabe lt nonscesscusbecadusaerilanebsszdueciustcnabeascncees 1 JA dE CIPO gener eee nnne tae aoe erent nee ae ee arene eee en eee ee een eee 3 PSS Cs SIMON Malk siirad sia aaae
109. t guidelines relating to the levels of stock will assist in determining whether consumables need to be ordered An internal requisition is commonly used to order replacement materials from a central store Requisition forms completed and forwarded to the appropriate person at the end of shift today should result in the supplies ordered or requisitioned being supplied to the cleaning store later in the day or early the next day before the next shift starts work ASEAN 2015 Trainee Manual Clean premises and equipment Apply ceilings surfaces and fittings cleaning techniques Work Projects It is a requirement of this Unit you complete Work Projects as advised by your Trainer You must submit documentation suitable evidence or other relevant proof of completion of the project to your Trainer by the agreed date 5 1 Provide video photographic real time or other acceptable evidence you have cleaned a ceiling providing evidence you have Assessed the area to be cleaned Selected appropriate equipment and chemicals Prepared the worksite job Applied appropriate techniques Tidied and returned the area to service Cleaned checked and stored the equipment which was used 5 2 Provide video photographic real time or other acceptable evidence you have cleaned nominated surfaces providing evidence you have Assessed the area to be cleaned Selected appropriate equipment and chemicals Prepared the worksite job Applie
110. t of this manual and your performance Work Projects Written Questions and Oral Questions It also indicates where you can find the subject content related to these assessment activities in the Trainee Manual i e under which element or performance criteria As explained in the Introduction however the assessors are free to choose which assessment activities are most suitable to best capture evidence of competency as they deem appropriate for individual students Work Written Oral Projects Questions Questions Element 1 Prepare to clean 1 1 Select the cleaning equipment to be used 1 2 3 1 2 Select the cleaning agents to be used 2 1 3 Select the protective clothing to be used 1 4 Check operation and safety of equipment that has been selected Element 2 Apply wet area cleaning techniques Assess areas to be cleaned 2 1 2 2 10 11 2 2 Prepare worksite 2 1 2 2 oa e 2 5 Clean check and store equipment and 21 22 15 chemicals ASEAN 2015 Trainee Manual Clean premises and equipment Assessment matrix Work Written Oral Projects Questions Questions Element 3 Apply dry area cleaning techniques Assess areas to be cleaned 3 1 3 2 10 11 3 3 3 3 Tidy worksite 3 gt 2 3 5 Clean check and store equipment and 3 1 3 2 17 14 chemicals 3 3 Element 4 Apply pressure washing techniques Assess area to be pressure washed 10 11 Clean areas using pressure washer o 18 19 E 4 5
111. techniques Putting all needles into a hard container purpose built for the containment of needles to guard against needle stick injuries Using designated chemicals and cleaning practices to clean and sanitise areas affected by body fluids and or faeces All body fluids must be treated as hazardous material never get complacent about dealing with body fluids they are dangerous and can kill Dry hands before touching power switches and or using electrical appliances water and electricity do not mix one mistake can kill Avoid rushing work hard without wasting time but rushing is a sure way of having an accident Never run in the workplace Follow manufacturer s instructions when using chemicals and when operating appliances Do not over stretch or over reach when handling items or undertaking cleaning tasks re position to a safer base starting point Be prepared to make two trips to the trolley cart to obtain items materials rather than trying to carry too much at the one time and risking strains trips or other injury Cleaning furniture Activities in cleaning furniture Pick up loose litter from chairs and tables and dispose of appropriately Wipe polished wooden surfaces with a damp cloth or a cloth moistened with a designated cleaning agent Wipe nominated upholstered surfaces with a damp cloth or a cloth moistened with a designated cleaning agent Polish designated areas with
112. tems ASEAN 2015 Trainee Manual Clean premises and equipment Presentation of written work Presentation of written work 1 Introduction It is important for students to present carefully prepared written work Written presentation in industry must be professional in appearance and accurate in content If students develop good writing skills whilst studying they are able to easily transfer those skills to the workplace 2 Style Students should write in a style that is simple and concise Short sentences and paragraphs are easier to read and understand It helps to write a plan and at least one draft of the written work so that the final product will be well organised The points presented will then follow a logical sequence and be relevant Students should frequently refer to the question asked to keep on track Teachers recognise and are critical of work that does not answer the question or is padded with irrelevant material In summary remember to e Plan ahead e Beclear and concise e Answer the question e Proofread the final draft 3 Presenting Written Work Types of written work Students may be asked to write e Short and long reports e Essays e Records of interviews e Questionnaires e Business letters e Resumes Format All written work should be presented on A4 paper single sided with a left hand margin If work is word processed one and a half or double spacing should b
113. to clean items Equipment needs to be cleaned after use so as to e Prevent odour problems e Maintain a high level of appearance e Maximise operational effectiveness e Leave the items ready for use next time they are needed Mops Dusting mops After use e Shake thoroughly in appropriate location outside e Wash in hot soapy water e Hang out to air dry Dusters Cleaning of dusters involves e Shake clean regularly in the appropriate location outside NS e Wash in accordance with the manufacturer s instructions ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques dry area cleaning techniques Brooms and brushes Cleaning of brooms and brushes involves e Shake clean e Wash in hot soapy water e Air dry ps Cloths and sponges These should be e Cleaned on a regular basis using hot soapy water e Left to air dry Conducting safety checks Safety checks must be undertaken as part of cleaning items and storing them Activities include e Reporting problems issues identified during cleaning processes e Removing unsafe items from use e Following manufacturer s instructions regarding regular inspections and checks e Checking all attachments and cords Undertaking preventative maintenance and repairs Only basic maintenance and repairs will be required e Adding fuel to petrol and diesel driven units e Greasing and oiling parts e Emptying
114. ts e Assessed the area to be cleaned e Prepared the worksite job e Applied appropriate techniques e Tidied and returned the area to service e Cleaned checked and stored the equipment which was used ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques Summary Apply wet area cleaning techniques When applying wet area cleaning techniques Talk to relevant people about the work Use personal knowledge and experience as key reference points for determining and evaluating what needs to be done Assess the work and determine what needs to be done and what resources will be required Identify the time required and the techniques to be used Cover items and use drop cloths as necessary Maintain positive customer relations Use appropriate techniques for the work to be done Ensure vacuum cleaners used for wet work are designated wet vacuum cleaners Balance need to clean with customer satisfaction and comfort Implement safety signage and or barriers Follow internal SOPs and Wis Wear use designated PPE Undertake clearing and pick up of loose items and litter as a basic first step Tidy worksite before returning it to service Clean check and store cleaning equipment and PPE after completion of task s Take action to replace replenish used items ASEAN 2015 Trainee Manual Clean premises and equipment Apply wet area cleaning techniques wet area cleaning technique
115. ty documents It is possible to obtain information direction to assist with identifying the PPE to be used and how it is to be used in cleaning processes Options include Checking to see if chemical supplier has a PPE Matrix this is a list or poster identifying all their chemicals and cross referencing them to all the necessary PPE which should be used Referring to internal Work Instructions or SOPs which set out not only the procedure to be followed and the equipment and supplies to be used when undertaking cleaning tasks but also list the PPE for each job Provision and use of PPE The following requirements apply to personal protective equipment Ne and clothing Ya Employers are required to provide necessary items and maintain them in safe working condition ltems must fit the person using wearing them properly ltems must be fit for purpose Employers must provide training in how to use the items Must wear use items exactly the way shown trained Must always wear use items when directed to do without exception the use of PPE is not optional it is mandatory ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean 1 4 Check operation and safety of equipment that has been selected Introduction Before using any item of cleaning equipment it must be standard practice to check to make sure the item is safe to use and is in a clean and fully operational condition Th
116. usiness The cleaning of driveways and parking lots is often a continuous job combined with the cleaning of other outdoor areas That is the one person crew may do nothing else for an entire shift but clean service these areas Cleaning options The cleaning of driveways parking lots and walkways paths will depend to a great extent on the size of the areas to be cleaned In practice e The smaller the area the greater the use of hand equipment tools e The bigger the area the greater the reliance on power equipment and or motorised equipment Cleaning these areas may require e Picking up and removal of loose litter and large items by hand e Using pushing a yard broom to sweep the area for smaller areas e Using a manual push sweeper or walk behind vacuum sweeper see http www sweepex com au industrial sweepers htm for larger surfaces e Spot cleaning removal of Chewing gum Qil spots marks Spills e Using high pressure hose to pressure wash surfaces and remove dirt see next section e Applying degreasers to assist in the cleaning process e Using mechanical scrubbers on problem areas e Using ride on motorised sweepers especially on very large area sites ASEAN 2015 Trainee Manual Clean premises and equipment Apply dry area cleaning techniques Floor polishing A floor polishing machine burnisher may be used to polish floors Keys in using a floor polisher are e P
117. y be used for stripping e Red pads brown pads and blue pads may be used for scrubbing e White pads and grey pads may be used for buffing Floor machines Many machines are available that combine the functions of different machines These can be referred to as floor machines The one machine may then have the capacity to e Scrub e Polish e Strip e Shampoo See http www floormachinesaustralia com do t floor 20scrubber These combination machines tend to be used in smaller businesses where there is no justification in buying a separate machine for each separate job Sweepers Sweepers are mechanical items used for sweeping removing litter and loose debris from large areas They are available in a variety of shapes sizes and styles Walk behind or pedestrian machines may be electrically powered while ride on and drive models may be battery gas or petrol driven ASEAN 2015 Trainee Manual Clean premises and equipment Prepare to clean See http www australiansweeper com au www sweeper com au Sweepers Scrubbers These are motorised ride on or walk behind pieces of equipment used to scrub hard surfaces to remove marks dirt some machines combine scrubbing and sweeping Pressure washers Pressure washers are used for high pressure water cleaning of surfaces They are commonly used e In kitchens to clean floors and help clean various items of equipment e Outside to clean public ar

TM_Clean premises and equipment_280115

Contents

Download Pdf Manuals

Related Search

Related Contents