Mobile Digital Video Recorder User Manual
Contents
1. HIKVISION Mobile Digital Video Recorder User Manual UD 6L0204D1015A01 User Manual of DS 8100HMI STM Series Mobile DVR Hikvision Network Digital Video Recorder User Manual This manual as well as the software described in it 1s furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Hikvision Digital Technology Co Ltd Hikvision Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical recording or otherwise without the prior written permission of Hikvision HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE REGARDING THE HIKVISION SOFTWARE HIKVISION DOES NOT WARRANT GUARANTEE OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS ACCURACY RELIABILITY CURRENTNESS OR OTHERWISE THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PER2. Figure 7 9 Tamper proof Handle Interface 4 Click the Apply and OK button to save the settings and exit 7 2 4 Detecting Video Loss Purpose Detect video loss of a channel and take alarm response action s Steps 1 Enter the Camera Settings interface and click the Set button for More Setting as shown in Figure 7 10 Menu gt Other Settings gt Camera gt Set Advanced Camera Analog 1 Image Settings M Mask M Tamper proof E Motion Detection i Video Loss Detection Handle Figure 7 10 Video Loss Settings Interface 2 Check the Video Loss Detection checkbox and click the Handle button for Video Loss Detection Refer to the step 3 of Chapter 7 2 3 for setting the arming schedule and alarm response action s 51 User Manual of DS 8100HMI STM Series Mobile DVR Exception Handle Arming Schedule Mon 10 ZA 50 20 0 6 0 3 0 E 7 OS O 4 0 0 8 Ome O Copy To All Week 4 4 gt gt 44 gt 4 44 gt 4 gt gt 4 4 gt 4 gt 4 gt 4 gt i gt th 4P 4 E Bice G gt d gt dh 459 Q o Ke lt E Pop up Image on Monitor Y Audio Warning All1 2 E Trigger Alarm Output OK Cancel Figure 7 11 Video Loss Handle Interface 7 2 5 Handling Exceptions Purpose Exception Settings refer to the handling methods of various exceptions e g e SD Card Full The SD card is full e SD Card Error Writing SD card error unformatted SD card etc e Network Disconnected Network cable is disconnect
3. Configuration Config 1 SSID 12345 Connect Mode MELER Security Type WPA PSK Encryption Type AES Key 1234567890 More Settings Set Cancel Figure 4 3 WiFi Settings Interface 2 Check the checkbox for Enable WiFi Configure the configuration file SSID security type encryption type and key Note Five configuration files are available and one SSID can be inputted for each file 3 Click the Set button for More Settings to set the IP address and DNS server for WiFi as shown in Figure 4 4 WiFi Settings DHCP IP Address Subnet Mask Default Gateway Auto obtain DNS Preferred DNS Server Alternate DNS Server OK Cancel Figure 4 4 IP amp DNS Settings for WiFi Note Check the checkbox for DHCP and Auto obtain DNS to automatically obtain IP address and DNS server for WiFi 4 After setting you can check the status of WiFi in the WiFi Status interface Menu gt Status gt WiF1 as shown in 35 User Manual of DS 8100HMI STM Series Mobile DVR Figure 4 5 WiFi Status Enable ia Status Unknown SSID Unknown Signal Strength Unknown IP Address Unknown AP List Figure 4 5 WiFi Status Interface 5 Click the Query button to search the available access point information of WiFi including SSID Security Type and Signal Strength as shown in Figure 4 6 AP List Security Type Signal Strength Figure 4 6 AP List 36 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 5 Platform
4. Figure 6 5 Sensor In Settings Interface 2 Sensor In is triggered by high or low level and you can set the parameters according to the vehicle 44 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 7 Other Functions 45 User Manual of DS 8100HMI STM Series Mobile DVR 7 1 Configuring Network Settings Purpose Network settings must be properly configured before you operate the Mobile DVR over network Steps 1 Enter the Network Settings interface as shown in Figure 7 1 Menu gt Basic Settings gt Network Network Settings IP Address 192 168 1 64 Subnet Mask NS ERER Default Gateway SACA EGO SCT Preferred DNS Server Alternate DNS Server Download Server IP MAC Address 00 40 30 11 11 61 Static IP Address 192 0 0 65 NTP Sel Apply OK Cancel Figure 7 1 Network Settings Interface 2 Configure the following settings including IP Address Subnet Mask Default Gateway DNS Server and Download Server IP Download Server IP should be set when uploading record files to the designate server 3 Click the Set button for NTP to configure the NTP server as shown in Figure 7 2 NTP a Synchronization Interval 60 NTP Server Figure 7 2 NTP Settings Interface 4 Check the NTP checkbox to enable the function Set the time interval between the two synchronizing actions with NTP server in Synchronization Interval and set the IP address of NTP Server Click OK button to save and exit 5 Click the OK
5. Enter the User Management interface Menu gt Other Settings gt User 2 Click the Add button to enter the Add user interface User Name Password Confirm Level Permission preview playback backup log query OK Cancel Figure 2 2 Add User Interface 3 Enter the information for new user including User Name Password and Level 20 User Manual of DS 8100HMI STM Series Mobile DVR Level Set the user level to Operator or Guest Different user levels have different operating permissions e Operator The Operator user has permission of Preview Playback Backup Log Search and Parameters Settings e Guest The Guest user has permission of Preview Playback Backup and Log Search 4 Click the OK button to save the settings and go back to the User Management interface 5 You can click the Delete button to delete the selected user and click the Modify button to modify the user information 2 3 Configuring Display Settings Purpose You can configure the language CVBS output standard system time etc Steps 1 Enter the Display Settings interface Menu gt Other Settings gt Display Display Settings Language English CVBS Output Standard NTSC System Time 2011 14 Enable Password a DST Settings Advance Setting DOWN IF OK Cancel Figure 2 3 General Settings Interface 2 Configure the following settings e Language The default language used is English CVBS Output Standard Select
6. Select Platform Platform VMS Server IP O ey A gor Port No 7660 Device Register ID OK Cancel Figure 5 2 iVMS Platform Settings 3 Configure the following settings Server IP Input the static WAN IP of 1VMS center server Server Port Connecting port between DVR and center server the default value is 7660 Device Register ID The ID registered in the 1VMS You need to register an ID for the device in the 1VMS platform before using 4 After setting you can check the status of 1VMS platform in the Platform Status interface Menu gt Status gt Plat 5 3 Accessing by the Push Mode Platform If you want to integrate the push mode platform and the Mobile DVR SDK and development support are provided Enter the Platform Settings interface Menu gt Basic Settings gt Platform select 3IG_SDK in Select Platform as shown in Figure 5 3 Platform Settings Select Platform 3G_SDK Server IP O Port No 10001 Device Register ID Register Password OK Figure 5 3 Push Mode Platform 39 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 6 Special Functions 40 User Manual of DS 8100HMI STM Series Mobile DVR 6 1 Configuring Startup and Shutdown Purpose There are two ways to start up and shut down the Mobile DVR You can set the delay time to shut down the DVR or set the time to automatically start up and shut down the DVR e Time delay shutdown Steps 1 Enter the Start Control interface as show
7. 3 Connect the KEY of DVR to the vehicle ignition switch 4 When switching on the vehicle the DVR starts up with the vehicle Negative pole ignition switch Mobile DVR F F gt ra re Cory oe Ede Lone sysie n P r my annection of Mobile DIR CAHMIECUCH O Votre ee e m ry ee rY A FOIE O TL FELOL Key of vehicle power a gt m O Nedan ic osifive Pole i Pole I ee ee o mo e e mm j Vehicle iginition switch negad ve pale gnu GIO Veh i C e batter ies Figure 1 9 Negative Pole Ignition Switch Ignition switch is connected to the negative pole of DC 12 24V of vehicle batteries Please make sure that the connection is correct and then follow the procedure below Steps 1 Connect the DC IN and KEY of DVR to the positive pole of vehicle batteries 2 Connect the DC IN to the negative pole of vehicle batteries 3 Connect the KEY of DVR to the vehicle ignition switch 4 When switching on the vehicle the DVR starts up with the vehicle 16 User Manual of DS 8100HMI STM Series Mobile DVR 1 3 2 Timing On Off Mobile DVR A r mi y ma me Vehicle Ower Sys tem NN gt z A m pm fy y Haf oe OT SPECT ON Ol Mobile VA A Damin EnF mr Om E j p ofconnecton Vehicle batteries Figure 1 10 Timing On Off Please follow the procedure below Steps L Connect the D
8. 3 In Playback mode it can be used to play or pause the video 4 In Auto switch mode it can be used to stop start auto switch a ee SSC Back to the previous menu O ee In video search interface it can be used to select all record files pom fe 13 PTZ 14 ESC 15 16 F1 17 8 F2 1 Troubleshooting Remote Control Note Make sure you have installed batteries properly in the remote control And you have to aim the remote control at the IR receiver in the front panel If there is no response after you press any button on the remote follow the procedure below to troubleshoot Steps User Manual of DS 8100HMI STM Series Mobile DVR Run the Client Management System to check and remember device ID The default ID is 255 This ID is valid for all the IR remote controls Press the DEV button on the remote control Enter the device ID from step 2 NR A Ww N e Press the ENTER button on the remote If the Status indicator on the front panel turns blue the remote control is operating properly If the Status indicator does not turn blue and there is still no response from the remote please check the following 1 Batteries are installed correctly and the polarities of the batteries are not reversed 2 Batteries are fresh and not out of charge 3 IR receiver is not obstructed If the remote still can t function properly please change a remote and try again or contact the device provider 1 3
9. Contigurine Preview Setting Sii 24 Chapt r 3 orori ONOONO OOOO ONCOR 26 Record SOUS niii iii A AA AAA AAA AA AAA AAA AA AAA AA NAAA AAA e 26 3 1 Configuring Encoding Parameters nad 27 Ded IMItIAILZINS SD Cards a aa 27 3 1 2 Configuring Record Settings cccssccccccsssscccceeessecccsseesseccesaueseceeeeueseeceeeeeaseceessuuaeeeessueasecessagees 27 3 2 Contigurine Motion Detection Record iii 29 3 3 CONMEUTING Alarm THeeered Recon 31 3 A SCALES Recoleta 31 Chapters aaa 33 Wireless Network Settings xvii AAA AAA AAA AAA ARANA 33 AE CONNUE Sais 34 A 2 COMMUMMAS WIFE AA 35 Chapt r Divinidad AAA AAA AA AAA 37 Platform SOULE rai oia AAA AA SEA AAA AAA A SAA AAA A AAA 37 5 L ACCESSIAS DY the WVS PAM asa 38 User Manual of DS 8100HMI STM Series Mobile DVR 5 2 ACCESSING DY CHE IVIVISH PIO Maa 38 5 3 Accessing by the Push Mode Plat Minis A AA 39 Chapter Di AAA AAA AAA AAA ARA AAA AAA AAA AAA AAA 40 E A 40 6 1 Configuring Startup and SHUTHOWN eii 41 6 2 Configuring Satellite POSITIONING oooonccnnccnoncnnnnnnnnnnnnnnonnonnnnononnnnnnnnnnnnnnnnononrnnnnnnnnnnnnnnonnnrnnnnnnanoss 42 6 3 COMMS UNMIS G SENSOR ads 43 BA CONMSUMINS Sensor wea E 43 Chapter TADA AAA AS 45 Other FUNCTIONS id daa 45 7 1 Configuring Network Setting S msi tunel A nae 46 L2 COMMUTES A O E E a E A 47 7 2 CONMBUFING Alarm IAD Utain a E O O sdaatatadeeanmeceduabameasees 47 72 2 COnNe ne Alar mn OUt erea aa N 48 7 2 3 Detecting Video TAMPeLing c
10. Starting Up and Shutting Down the DVR There are two ways to start up the DVR startup with vehicle ignition and time delay shutdown and timing on off Note You can also use the power switch on the front panel to turn on or off the device If you want to use the following two ways to start up the device please turn on the power switch first 1 3 1 Vehicle Ignition Startup There are two kinds of vehicle ignition switch positive pole ignition switch and negative pole ignition switch For detailed time delay shutdown please refer to Chapter 6 1 Notes 1 Please contact the vehicle manufacturer for the information about the connecting mode of starting switch 2 Positive pole ignition switch is used by most cars Positive pole ignition switch Mobile DVR Ss a ess aaa VENCIO power system TT Connection of Mobile DVR A Point of connection Key of vehicle power e e e oe om oo 3 Positive Negative pole pole ES Vehicle iginition switch positive pole ignitigh Figure 1 8 Positive Pole Ignition Switch 15 User Manual of DS 8100HMI STM Series Mobile DVR Ignition switch is connected to the positive pole of DC 12 24V of vehicle batteries Please make sure that the connection is correct and then follow the procedure below Steps 1 Connect the DC IN of DVR to the positive pole of vehicle batteries 2 Connect the DC IN and KEY to the negative pole of vehicle batteries
11. example when an alarm triggered the recording at 10 00 if you set the pre record time as 5 seconds the camera records it at 9 59 55 Post record The time you set to record after the event or the scheduled time For example when an alarm triggered the recording ends at 11 00 if you set the post record time as 5 seconds it records till 11 00 05 6 If the settings can also be set to other channels click Copy 7 Click the Apply button to save the settings 3 2 Configuring Motion Detection Record Purpose In the live view mode once a motion detection event takes place the device can analyze it and do many actions to handle it In this chapter you can follow the steps to schedule a record which triggered by the detected motion Steps 1 Enter the Advanced Camera Settings interface Menu gt Other Settings gt Camera gt Set for More Setting 2 Check the checkbox before Motion Detection and click the Area Settings button for Motion Detection to set the areas for motion detection Note By default the whole area is armed for motion detection You can perform the following steps to disarm some areas or press the A button on the remote control to clear all the mask areas and then perform the following steps to arm some specific areas as desired 29 User Manual of DS 8100HMI STM Series Mobile DVR Steps 1 Press the Edit key on the remote control and a red block appears on the screen 2 Press the Direction key on the re
12. for each channel e Tamper proof Detection Trigger alarm when the lens is covered and take alarm response action s For detailed information please see Chapter 7 2 3 e Motion Detection Once a motion detection event takes place the device can analyze it and do many actions to handle it For detailed information please refer to Chapter 3 2 e Video Loss Detection Detect video loss of a channel and take alarm response action s Please see Chapter 7 2 4 for detailed information 2 5 Configuring Preview Settings Purpose Preview settings can be customized according to different needs You can configure the preview mode mute or turning on the audio etc Steps 24 User Manual of DS 8100HMI STM Series Mobile DVR 1 Enter the Preview Settings interface as shown in Figure 2 9 Menu gt Other Settings gt Preview Preview Settings Preview Mode 252 Dwell Time No Switch Camera Order Set Enable Audio Output Mi OK Cancel Figure 2 9 Preview Settings Interface 2 The settings available in this menu include e Preview Mode Designates the display mode to be used for preview e Dwell Time The time in seconds to dwell between switching of channels when enabling auto switch in preview e Enable Audio Output Enables disables audio output for the selected video output 3 Click the Set button to set the camera order as shown in Figure 2 10 Camera Order OK Cancel Figure 2 10 Camera Orde
13. un a gt a gt T E T8 Tg DA e O IO Es NS E 4 i gt ibh d gt ib 4 db 49 che Po a a aa aa he gt 4 gt 4 gt 4 gt 8 4 Fd onan art WN Figure 7 4 Arming Schedule Interface 5 Check the checkbox for Handle Type and click the Set button for Handle Type to configure alarm response actions including Pop up Image on Monitor Audio Warning and Trigger Alarm Output as shown in Figure 7 5 Handle Type E Pop up Image on Monitor E Audio Warning All1 2 E Trigger Alarm Output OK Cancel Figure 7 5 Handle Type Interface 6 Click the Apply and OK button to save the settings and exit 7 Click the Apply button on the Alarm Input Settings interface to confirm the settings 7 2 2 Configuring Alarm Output Purpose Arming schedule duration alarm name can be configured for alarm output Steps 1 Enter the Alarm Output Settings Interface as shown in Figure 7 6 Menu gt Other Settings gt AlarmOut 48 User Manual of DS 8100HMI STM Series Mobile DVR Alarm Output Alarm Output No Alarm Name Duration Arming Schedule Copy To Figure 7 6 Alarm Output Settings Interface 2 Select an alarm output and set alarm name and duration Note Two relay alarm output are available which are Al amp B1 A2 amp B2 If Manually Stop is selected in the dropdown list of Duration you can clear it only through Client Software System 3 Click the Set button to configure the arming schedule for alarm out
14. C IN and KEY of DVR to the positive pole of vehicle batteries Ze Connect the DC IN and KEY of DVR to the negative pole of vehicle batteries Note For detailed information about automatically starting up and shutting down the DVR please see Chapter 6 1 1 4 Connecting to Alarm Input Output Device Connecting to Alarm Input DS 8100HMI STM series Mobile DVR adopts the high low level electrical signals triggering high level 6 36 VDC low level 0 5 VDC to realize alarm input And in order to avoid error report caused by voltage fluctuation no alarm will be triggered by voltage ranging of 5 6VDC Alarm input and Mobile DVR must be with common grounding Mobile DVR Figure 1 11 Alarm Input Connection Connecting to Alarm Output The contact closure signal is used for the alarm output triggering When there is an alarm output triggered the contact A and B of the Alarm Output will be closed Therefore the active alarm device must be connected 17 User Manual of DS 8100HMI STM Series Mobile DVR Mobile DVR Figure 1 12 Alarm Output Connection 1 5 SD Card Installation Notes L Ze gt Please disconnect the power before and during the SD card installation A factory recommended SD card should be used for this installation After installation please initialize the SD card before recording Please refer to Chapter 3 1 1 for detailed information Steps 1 Ze Insert t
15. MITTED BY SOME STATES THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU User Manual of DS 8100HMI STM Series Mobile DVR Thank you for purchasing our product This manual applies to DS 8100HMI STM series Mobile DVR please read it carefully for the better use of the device This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual User Manual of DS 8100HMI STM Series Mobile DVR Regulatory information FCC information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a comm
16. OSD Position button and use the F2 key and direction keys on remote control to adjust the OSD position 7 Click the Set button for More Setting to configure the video parameters mask area motion detection etc Advanced Camera Analog 1 Image Settings Set M Mask Area Settings M Tamper proof E Motion Detection E Video Loss Detection OK Cancel Figure 2 7 More Setting Interface 23 User Manual of DS 8100HMI STM Series Mobile DVR e Image Settings Click Set button for Image Settings to adjust the video parameters including Brightness Contrast Saturation and Hue Brightness seur Contrast OK Saturation Cancel Hue Figure 2 8 Image Settings Interface e Mask You are allowed to configure the privacy mask zones that cannot be viewed and recorded by the operator Check the checkbox before Mask and click the Area Settings button for Mask to set the mask areas Please follow the procedure below to set the areas Steps 1 Press the Edit key on the remote control and a red block appears on the screen 2 Press the Direction key on the remote control to adjust the position of the red block 3 Press the Enter key on the remote control to save the position of the red block 4 Press the Direction key on the remote control to adjust the size of the block and press Enter key to save the setting Note Press the A button on the remote control to clear all the mask areas and up to 4 areas can be configured
17. P and SADP are supported Remote search playback download of record files Remote parameters setup remote import export of device parameters Remote viewing of the device status system logs and alarm status RS 232 RS 485 parameters configuration and transparent channel transmission Development Scalability SDK for Windows and Linux system O Development support and training for application system User Manual of DS 8100HMI STM Series Mobile DVR TABLE OF CONTENTS Hikvision Network Digital Video Recorder User Manual csccscssceccsccccsccccsccsceccsccccscsscsccsceccsceecncs 1 Chapter di AAA AAA 9 o osecciio ci cecs cers cuib ace sect tess iie cece ce less aceasta eds Sere care Sheds Sosa alicectatoctnos cualcacustctneatneabeasumneidects 9 ad Front Pane liana Rear PM e e e eae da ed 10 aL A POU eal OCA E nO 10 TL2 Rear OO 11 LLS Pin Derinition OF Interfaces ii A A A 11 1 2 R Remote Control Opera Sieen a E E A eaeadieonedaueeset 13 1 3 Starting Up and Shutting Down the DV Rionansa ii 15 t3 T Vehicle lenition SAUS 15 L 2 MMM OMO oeiee A T c aii 17 14 Connectins to Alarm Input OUTPUT DEV CE e ias 17 5D Cand instala al 18 ES SIM AUIM Card still A A a 18 Chapter Zaira io 19 BaSiC OD ClatiON Suri AEE OOO 19 ABMA AME NO se ecias cesta doen deanenioadiceunets asansasnechagacsaacsneseaahoosetanseeac3sabesesecmat N 20 2 2 Managing User ACUM os 20 2 3 Contisgurine Display Setting Sai 21 ZA Contsurine Camera 23 2 5
18. Settings User Manual of DS 8100HMI STM Series Mobile DVR The Mobile DVR can be remotely accessed via 3 platforms WVS platform 1VMS platform and Push Mode platform Make sure the parameters configured are valid for the platform you select for login 5 1 Accessing by the WVS Platform Steps 1 Enter the Platform Settings interface Menu gt Basic Settings gt Platform 2 Select Platform WVS in Select Platform as shown in Figure 5 1 Platform Settings Select Platform Platform WVS Server IP NN ALL NO 5660 Device Register ID 123123123 Register Password 2222A Figure 5 1 WVS Platform Settings 3 Configure the following parameters Server IP Input the static WAN IP of WVS server Port No The same as the client port of server the default value is 5660 Device Register ID and Register Password The ID and password of the Mobile DVR registered in the manage system of WVS The ID should start with 1 and with length of 9 numbers You need to register the ID and password for the device in the WVS platform before using 4 After configuration you can enter the Platform Status interface Menu gt Status gt Plat to check the status of WVS platform 5 2 Accessing by the 1VMS Platform Steps 1 Enter the Platform Settings interface Menu gt Basic Settings gt Platform 2 Select Platform iVMS in Select Platform as shown in Figure 5 2 38 User Manual of DS 8100HMI STM Series Mobile DVR Platform Settings
19. Steps 1 Enter the G Sensor Settings interface as shown in Figure 6 4 Menu gt Basic Settings gt G Sensor G Sensor Settings Module RS 232 X Alarm T 0 Y Alarm lt O Z Alarm n 1 1 Alarm Handle Audio Alarm E All1 2 Trigger Alarm Output E E E OK Cancel Figure 6 4 G Sensor Settings Interface 2 Select the Module and set the alarm value for X Alarm Y Alarm and Z Alarm Note X Y and Z represent the direction of acceleration and G G 9 8 m s is the unit of alarm value 3 Configure the actions to handle the exception Audio Alarm and Trigger Alarm Output are available Please see Chapter 7 2 2 for alarm output configuration 4 Click the OK button to save the settings and exit Note The status of G Sensor can be checked in G Sensor Status interface Menu gt Status gt G Sensor 6 4 Configuring Sensor In Purpose Sensor In can be used for collecting driving information of the vehicle including pedal braking turning left right reversing etc Before you start 43 User Manual of DS 8100HMI STM Series Mobile DVR You need to connect an external traveled recorder to the device for obtaining and providing the driving information of the vehicle Steps 1 Enter the Sensor In Settings interface as shown in Figure 6 5 Menu gt Basic Settings gt Sensor In Sensor In Settings Interface Behavior Trigger Level 1 Brake High y 2 Turn Left High y 3 Turn Right High 4 Roll Back High y
20. aa S Figure 1 1 Front Panel Note After opening the front panel lock you can see the interfaces shown above Table 1 1 Description of Front Panel Receiver for IR remote control Please make sure the receiver is unblocked by any object USB USB port SIM UIM SIM UIM card slot 10 User Manual of DS 8100HMI STM Series Mobile DVR su 1 1 2 Rear Panel GPS ANIS WIFI ANT4 ALARM amp SENSOR IN Figure 1 2 Rear Panel Note The descriptions are subject to the physical product Table 1 2 Description of Rear Panel 10 pin aviation plug for RS 422 interface 3 alarm inputs 2 alarm outputs and 4 Sensor In interfaces for collecting driving information Master slave 3G antenna WIFI antenna reserved 1 1 3 Pin Definition of Interfaces e Pin Definition of Alarm amp Sensor In Interface 11 User Manual of DS 8100HMI STM Series Mobile DVR Sensor in 3 sensor in 2 Sensor in 4 412 gt Ma Alarm Input 1 Alarm Input 3 GND VW C Reserved Alarm Input 2 Sensor in 1 Alarm Output 1 Figure 1 3 Pin Definition of Alarm amp Sensor In Interface e Pin Definition of RS422 Interface Ep way Audio Ep RS485 T Vout Figure 1 4 Pin Definition of RS422 Interface e Pin Definition of CH1 2 3 4 Interface 1 Video Input 2 Audio Input 3 12 VDC Voltage Output 4 GND Figure 1 5 Pin Definition of CH1 2 3 4 Interface e Pin Def
21. art Ensure the network connection of the PC running FTP server and the DVR is valid and correct Run the FTP server on the PC and copy the firmware into the corresponding directory of your PC Note Refer to the user manual of the FTP server to set the FTP server on your PC and put the firmware file into the directory as required 1 Enter the Upgrade interface and set upgrade type to FTP Upgrade as shown in Figure 8 3 Menu gt Maintenance gt Upgrade Firmware Upgrade Upgrade Type FTP Upgrade FTP Server Address Upgrade Cancel Figure 8 3 Upgrade Interface 2 Input the FTP Server Address in the text field 3 Click the Upgrade button to start upgrading 56 User Manual of DS 8100HMI STM Series Mobile DVR 8 2 2 Searching amp Exporting Log files Purpose The operation alarm exception and information of the device can be stored in log files which can be viewed and exported at any time Steps 1 Enter the Log Search interface Menu gt Maintenance gt Log Search Log Search Major Type All Minor Type All Start Time 2012 0 End Time 2012 4 4 4 4 4 4 aa a g A vr _ w oP oP Search Cancel Figure 8 4 Log Search Interface 2 Set the log search conditions including Major Type Minor Type Start Time and End Time 3 Click the Search button to search log files Log Search Major Type Record Time Minor Type Parameter 8 Informati 10 24 2012 08 35 1 Start Record N A T Ope
22. audrate 115200 Data Bit 8 Stop Bit 1 Parity None Flow Control None Used As Console Figure 7 13 Serial Port Settings Interface 2 Select serial port type and configure the parameters including baud rate parity and usage 3 Click the OK button to save the settings and exit 53 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 8 Device Management and Maintenance User Manual of DS 8100HMI STM Series Mobile DVR 8 1 Checking Status The status of recording 3G platform satellite positioning G Sensor alarm and WiFi can be checked in the Status interface Menu gt Status Status aT BR B Record Dial Plat Position D E G Sensor Alarm Record Status Figure 8 1 Status Interface 8 2 Management and Maintenance 8 2 1 Upgrading the System Purpose The Mobile DVR can be upgraded by local USB flash disk or remote FTP server Steps e Upgrading by local USB flash disk Before you start Connect your DVR with a local UBS flash disk where the update firmware file is located in the root directory 1 Enter the Upgrade interface and select upgrade type as USB Upgrade as shown in Figure 8 2 Menu gt Maintenance gt Upgrade 55 User Manual of DS 8100HMI STM Series Mobile DVR Firmware Upgrade Upgrade Type USB Upgrade v Refresh USB1 1 y Upgrade Cancel Figure 8 2 Upgrade Interface 2 Click the Upgrade button to start upgrading e Upgrading by remote FTP server Before you st
23. button in the Network Settings interface to confirm the settings and exit 46 User Manual of DS 810O0HMI STM Series Mobile DVR 7 2 Configuring Alarm 7 2 1 Configuring Alarm Input Purpose Configure the settings for alarm input including trigger level arming time alarm response actions etc Steps 1 Enter the Alarm Input Settings interface as shown in Figure 7 3 Menu gt Other Settings gt AlarmIn Alarm Input Alarm Input No A lt 1 Alarm Name Trigger Level High Level Trig Record Channel Set Schedule Set Handle Type Copy To OK Cancel Figure 7 3 Alarm Input Settings Interface 2 Configure the Alarm Name and Trigger Level of the selected alarm input Note 3 high low level triggered high level 6 36 VDC low level 0 5 VDC alarm input interfaces are provided In order to avoid error report caused by voltage fluctuation no alarm will be triggered by voltage ranging of 5 6VDC 3 external alarm is input Click the Set button for Trig Record Channel and select one or more channels which will start to record when an Click the Set button for Schedule to set the arming schedule as shown in Figure 7 4 Up to 8 time periods can be set within each day You can click Copy to copy the settings to other days 47 User Manual of DS 8100HMI STM Series Mobile DVR Schedule Arming Schedule Mon OS 24 i i B 1 i o a Y A 0 a wT a gt ai i F S
24. cccccsssseccecsssscccccsessecccseeueeccessaeseceeesseneeeeesseaseceesseauseeesseaaeceesaaees 49 7ed Detecine Video LOSS aa ae E E IN 51 TAS HANGING Except aaa 52 7 3 CONMEUTINE senal PO anni dianas 53 E TE SLE E dada 54 Device Management and Maintenance sesssseseseseececeseececescececesescecesescecessececeseececeseececeseececesesceceseecee 54 Ole dle SUA AA a a A A A E 55 8 2 Management and Malnten antic tiesto eatautaesedesaedeeiuaaseraseadedeeiaeaateaaers 55 8 2 Uperading ne Syste Minnene en a enesctansan aos aReiyecnneusnaReN 55 8 2 2 Searching Exporting Log files cocccoooncccnnccnoncnnnnncnnconnnnonancnnonononnnnnnnnnanrnnnnnnnnnnnnnnonannononnnos 57 8 2 Restoring Default Settings dias 58 8 2 4 Importing Exporting Configuration Files occcccccnnncnnnnnnnnnnnnnnnonnnononononnnononononononononononinnninanonos 58 8 2 5 Viewing System Information cccsseeccccccssssccccceessecccccaueeceeseuaseceessueseeeeeeeeaseeeessuaaseeessaageseesagees 59 8210 BACKUP DEVIN N 59 6237 REDOOtINE DVRs 60 a O 61 OSS Vina cotos oNiciaans 61 OS 62 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 1 Introduction User Manual of DS 8100HMI STM Series Mobile DVR 1 1 Front Panel and Rear Panel 1 1 1 Front Panel The front panel of DS 8100HMI STM is shown in figure below OFF O 02 Please shut down the device before plugging in or removing POWER e SD card or SIM card SIM UIM RECORD IR n
25. cord file by pressing the Enter key on the remote control 3 Click the Play button to play back the checked record file 4 Click the Export button to export the checked record file Before exporting please connect a USB device with the DVR 32 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 4 Wireless Network Settings User Manual of DS 8100HMI STM Series Mobile DVR 4 1 Configuring 3G Purpose Set the parameters for 3G before using it Steps 1 Enter the Dial Settings interface as shown in Figure 4 1 Menu gt Basic Settings gt Dial Dial Settings Enable Dialing Y More Settings PIN Management OK Cancel Figure 4 1 Dial Settings Interface 2 Check the checkbox for Enable Dialing 3 Click the Set for More Settings to configure private network parameters as shown in Figure 4 2 Note Please contact the network operator for private network parameters PIN management is reserved Dial Settings APN Dial Number User Name Password Verification Protocal OK Cancel Figure 4 2 Private Network Settings Interface 4 After configuration you can check the dial status in the Dial Status interface Menu gt Status gt Dial 34 User Manual of DS 8100HMI STM Series Mobile DVR 4 2 Configuring WiFi Purpose Set the parameters for WiFi before using it Steps 1 Enter the WiFi Settings interface as shown in Figure 4 3 Menu gt Basic Settings gt WiFi WiFi Settings Enable WiFi
26. e DVR Product Key Features Main Features Newly featured GUI with easy and flexible operation The first channel supports up to 4CIF real time encoding and other channels support CIF real time encoding H 264 standard video compression with high reliability and superior definition Two pluggable SD cards are connectable each card with a maximum of 32GB storage capacity Power off protection of data with the built in redundant power supply Built in 3G WCDMA CDMA2000 module Built in high sensitivity satellite positioning module Interfaces are provided for recording driving information of the vehicle s turning left right braking reversing etc Aviation connectors adopted for all video input output audio input output and power supply ensuring high stability of signal connection O Delay Omin 6h shutdown and 24 hour scheduled startup shutdown configurable O Wide range power input 6 VDC 36 VDC Aluminum chassis Local Monitoring O 1 4 division live view is supported and the display sequence of screens is adjustable The selected live view channel can be shielded O Motion detection tamper proof video exception alarm and video loss alarm functions O Privacy mask Record and Playback O Fach camera can be configured with normal and event compression parameters Sub stream can be configured locally O Multiple recording types normal alarm motion motion alarm motion amp alarm O 8 recording tim
27. e periods with separate recording types configurable O Pre record and post record for alarm and motion detection for recording O Search and play back record files by channel number recording type start time end time etc O Support pause fast forward slow forward skip forward and skip backward when playback Backup O Export video data by USB device O Management and maintenance of backup devices Alarm and Exception Management of alarm input output Management of alarm for video loss motion detection video tampering Configurable arming time of alarm input output User Manual of DS 8100HMI STM Series Mobile DVR Alarm for video loss motion detection tampering video input output standard mismatch illegal login network disconnected IP confliction SD card error and SD card full Alarm triggers full screen monitoring audio alarm and alarm output Motion detection and alarm can trigger recording Exception can trigger audio alarm and alarm output Automatic restore when system 1s abnormal Other Local Functions Two level user management admin user 1s allowed to create many operator accounts Operation alarm exceptions and log recording and searching Import and export of device configuration file Network Functions 1 self adaptive 10M 100M network interface WCDMA and CDMA2000 supported WiFi supported Remote configuration and operation by iVMS platform and WVS platform TCP IP protocol DHCP DNS NT
28. ed e IP Conflicted Duplicated IP address e Illegal Login Incorrect user id or password e Video Output Standard Mismatch I O video standards do not match e Abnormal Recording No space for saving recorded files Steps 1 Enter the Exception interface as shown in Figure 7 12 Menu gt Other Settings gt Exception Exception Exception Type SD Card Full E Audio Warning All1 2 Trigger Alarm Output MM E OK Cancel Figure 7 12 Exception Interface 52 User Manual of DS 8100HMI STM Series Mobile DVR 2 Select the Exception Type and set the alarm response action s 3 Click the Apply button to confirm the settings 7 3 Configuring Serial Port Purpose RS 232 and RS 485 are provided to be configured The RS 232 port can be used in two ways e Parameters Configuration Connect a PC to the DVR through the PC serial port DVR parameters can be configured by using software such as HyperTerminal The serial port parameters must be the same as of the device when connecting with the PC serial port e Transparent Channel Connect a serial device directly to the device The serial device will be controlled remotely by the PC through the network and the protocol of the serial device The RS 485 port can be used for transparent channel only Steps 1 Enter the Serial Port Settings interface to configure the parameters as shown in Figure 7 13 Menu gt Basic Settings gt SerialPort Serial Settings Serial Port Type RS 232 B
29. ercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement CE This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Un
30. erial devices and for the user only the point to point transmission is seen and the actual transmission is ignored e VPDN Virtual Private Dial up Network is a network that uses primarily public telecommunication infrastructure such as the internet to provide remote office or travelling users access to a central organization network such as the ISP private network financial network and so on e WiFi WiFi is a mechanism of the wireless connecting electronic devices A device enabled with WI FI such as PC video game console can connect to the internet via a wireless network access point 61 User Manual of DS 8100HMI STM Series Mobile DVR FAQ e Why does my DVR make a beeping sound after booting The possible reasons for the warning beep on the device are as follows a There is no SD card installed in the device b The SD card is not initialized c SD card error To cancel the beeping sound and use the device without SD card enter the Exception Settings interface For detailed information see Chapter 7 2 5 Handling Exceptions e DVR fails to start up after connecting the power Possible reasons a Incorrect voltage input 6 36 VDC and power consumption gt 50W b The power switch is not turned on c The power connections are incorrect and please refer to Chapter 1 3 d The motherboard or power functions abnormally In case of hardware failure please contact the supplier of the product e Fail to co
31. g default settings 8 2 4 Importing Exporting Configuration Files Purpose The configuration files of the DVR can be exported to local device for backup and the configuration files of one device can be imported to multiple device devices if they are to be configured with the same parameters Before you start Connect your DVR with a local UBS device Steps 1 Enter the Import Export Configuration Files interface as shown in Figure 8 7 Menu gt Maintenance gt Configuration 58 User Manual of DS 8100HMI STM Series Mobile DVR Import Export Configuration Refresh USB1 1 Y FreeSpace 173MB Import Export Cancel Figure 8 7 Import Export Configuration Files 2 Click the Export button to export configuration files to the USB device 3 Before importing a configuration file you need to connect a USB device with the DVR and the configuration file should be placed in the root directory of the USB device Click the Import button After the import process is completed you must reboot the device to activate the new configuration 8 2 5 Viewing System Information Steps 1 Enter the System Information interface Menu gt Maintenance gt Information System Information Device Name mobileDVR Model DS 8104HMI STM Serial No 0820121022CCCHO000000 TIWCVLU Firmware Version V0 0 0 Build 00000 Encode Version V0 0 Build 00000 Panel Version V0 0 Figure 8 8 System Information 2 You can view the device name m
32. he key and turn in counterclockwise direction to open the front panel lock Insert the SD card horizontally to the corresponding slot according to the cut position shown on the front panel Note You can push the SD card to check whether the card is installed properly If the card can pop up automatically it means it is well installed Figure 1 13 SD Card Installation 1 6 SIM UIM Card Installation Please insert a SIM UIM card to access to the 3G network Note Please disconnect the power before and during the SIM UIM card installation Steps 1 Insert the key and turn in counterclockwise direction to open the front panel lock 2 Press the yellow release button on the left side to get access to the SIM UIM card holder 3 Pull out the card holder and insert the SIM UIM card 4 Push the SIM UIM card holder back into the slot 18 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 2 Basic Operations User Manual of DS 8100HMI STM Series Mobile DVR 2 1 Main Menu The main menu is shown in Figure 2 1 Menu E Video Search Basic Settings Other Settings X SD Card Status MEIEN Video Search Event Search and Playback Figure 2 1 Main Menu 2 2 Managing User Accounts There is a default account in the device Administrator The Administrator user name is admin and the password is 12345 The Administrator has the permission to add and delete user and configure user parameters Steps 1
33. hown in Figure 3 6 Menu gt Video Search 31 User Manual of DS 8100HMI STM Series Mobile DVR Video Search Camera Analog 1 Video Type All Start Time 7 0 End Time ZUTE rape 77 oP oP i dh dh dh 4b SU oP oP ioe search Cancel Figure 3 6 Video Search Interface 2 Set search conditions and click the Play button to enter the Playback interface Note When more than 4000 recorded files are found the top 4000 items have the priority to be played back The playback speed can be adjusted by pressing the Up and Down keys on the remote control 3 Set search condition and click Search button to enter the Search Results interface as shown in Figure 3 7 Choose a record file you want to play back Search Results CH Start Time End Time Size MA 10 17 2012 08 47 13 09 14 52 30 059 KB MA 10 17 2012 09 19 47 09 27 52 9 102 KB MA 10 17 2012 09 37 48 09 42 56 5 573 KB MA 10 17 2012 09 44 22 09 53 46 10 204 KB E A1 10 17 2012 09 55 14 10 03 18 9 053 KB MA1 10 17 2012 10 06 59 10 13 03 7 123 KB MA 10 17 2012 10 31 40 10 35 46 6 560 KB MA1 10 17 2012 11 49 20 11 50 05 817 KB MA1 10 17 2012 11 51 35 12 37 39 51 272 KB E A1 10 17 2012 15 01 46 16 52 58 120 496 KB mm AA LEa m iraa T a N Ea ee m e AA CTZ AAN y ie dar der dl aA Total Size OKB Play Export Cancel Figure 3 7 Search Result Interface Notes 1 Select the record file by pressing the Up and Down keys on the remote control 2 Check the re
34. inition of A V OUT Interface 1 Video Output 2 Audio Output 3 12 VDC Voltage Output 4 GND Figure 1 6 Pin Definition of A V OUT Interface 12 User Manual of DS 8100HMI STM Series Mobile DVR 1 2 IR Remote Control Operations The device may also be controlled with the included IR remote control shown in Figure 1 7 Figure 1 7 Remote Control The description of buttons on the remote control is shown in Table 1 3 Table 1 3 Description of the IR Remote Control Buttons DEV Input device number 1 Input number symbol and character 3 Number keys 2 Switch to the corresponding channel in Live View mode 13 User Manual of DS 8100HMI STM Series Mobile DVR 1 Enter the edit status and then delete the character in the front of the cursor Edit 2 It can also be used to tick checkbox 3 In Playback mode it can be used to generate video clips for backup Switch between input methods Number English symbol when in the edit 2 A status E 11 Switch between single screen and multi screen mode Up Down Left Right 1 The DIRECTION buttons are used to navigate between different fields and items in menus Direction keys 2 In the playback interface they are used for fast forward slow forward rewind 3 In Live View mode these buttons can be used to switch channel s 1 The ENTER button is used to confirm selection in any of the menu modes ENTER 2 It can also be used to tick checkbox
35. ion See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info User Manual of DS 8100HMI STM Series Mobile DVR Preventive and Cautionary Tips Before connecting and operating your device please be advised of the following tips The installation of mobile DVR must be done by qualified automobile assembly manufacturers or dealers And the device should be installed at well ventilated location inside the automobile Please make yourself be familiar with the power connection before installation A factory recommended SD card should be used for this device The wireless and satellite positioning antennas should be installed on the location with high signal strength and lightning protection measures And make sure the antennas are not covered or blocked by any other object When both the master and slave antennas are connected locate them vertically with above 20cm distance from each other The device contains no user serviceable parts Do not disassemble the device for repair or maintenance by yourself If you encounter any questions about this device please contact the technicians from HIKVISION or its authorized suppliers User Manual of DS 8100HMI STM Series Mobil
36. mic IP address to the host on the network Dual Stream Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network e GPS GPS Global Positioning System is a space based global navigation satellite system that provides location and time information in all weather and anywhere on or near the earth where there is an unobstructed line of sight to 4 or more GPS satellite e G Sensor G sensor Gravity sensor can sense the change of the accelerated force such as the shaking free falling and lifting And those changes of the accelerated force can be sensed by the G sensor in a means of electrical signals and then link certain action according to the changes of the electrical signals When applied in the hard disk protection G Sensor can check the current status of the hard disk in case of the affection of the R W function by the sudden change of the accelerated force e NTP NTP is Network Time Protocol and it is a protocol used to synchronize the computer time e Sensor In Sensor In is a built in module on the mobile DVR used to record the movement information of the vehicle such as the braking left turning and rightOturning and so on The information can be used for analysis of an accident e Transparent Channel Transparent channel is a mechanism which analyzes the IP datagram and sends it by the serial interface It extends the control distance of the s
37. mote control to adjust the position of the red block 3 Press the Enter key on the remote control to save the position of the red block 4 Press the Direction key on the remote control to adjust the size of the block and press Enter key to save the setting Note You can press the A button on the remote control to clear all the mask areas 5 Press the Menu key on the remote control to set sensitivity You can set the level from 1 to 6 and off is also selectable Click the OK button to save and exit 6 Press the Enter key on the remote control to save the settings and then press ESC key to exit 3 Click the Handle button for Motion Detection to set arming schedule and alarm response actions as shown in Figure 3 4 Alarm response actions e Pop up Image on Monitor When an alarm is triggered the local monitor displays full screen video image from the alarming channel configured for full screen monitoring e Audio Warning Trigger an audible beep when an alarm is detected e Trigger Alarm Output Trigger an alarm output when an alarm is triggered Please refer to Chapter 7 2 2 for alarm output settings Exception Handle Arming Schedule Mon 10535 0 24 50 2 OS 0 0 6 0 3 Oe O 70 4 05350 8 0 Copy To All Week 1 dh dh 4 i gt 4b 4 4 gt Smee See i gt 4 ee Bic Pleo Bie 4 dh dh 4b fe ie a a gt 45 4 gt 4 E Pop up Image on Monitor E Audio Warning Ant 2 E Trigger Alarm Ou
38. n in Figure 6 1 Menu gt Basic Settings gt Start Start Control Auto Work Type Halt Delay Delay Time 0 minute Figure 6 1 Start Control Interface Halt Delay 2 Select Halt Delay in Auto Work Type and set the delay time from 0 min to 6 hours e Timing on off Steps 1 Enter the Start Control interface as shown in Figure 6 2 Menu gt Basic Settings gt Start Start Control Auto Work Type Auto Working Date Monday Time Segment 1 O s O S to 0 Time Segment 2 O S50 Sto0 Date Copy All OK Cancel Figure 6 2 Start Control Interface Auto Working 41 User Manual of DS 8100HMI STM Series Mobile DVR 2 Select Auto Working in Auto Work Type 3 Choose the day you want to set schedule for automatically starting up and shutting down the DVR Note Two periods can be configured for each day And the time periods can t be overlapped each other If the schedule can also be set to other days click Copy 6 2 Configuring Satellite Positioning Purpose Satellite positioning is mainly used for positioning and speed limit alarm Steps 1 Enter the Satellite Positioning Settings interface as shown in Figure 6 3 Menu gt Basic Settings gt Position Position Settings Position Module Built in Satellite Time Adjusting Time Zone GMT 08 00 Beijing Urw Speed Unit km h v Speed Limit 100 Audio Alarm All1 2 Trigger Alarm Output a All1 2 3 4 Display Channel m ENE Figure 6 3 Satellite Positioning Se
39. nnect 3G Possible reasons for 3G connection failure are as follows a Dialing is not enabled b APN dial number user name and password should be set for 3G VPDN private network c No 3G antenna connected When both the master slave antennas are connected locate them vertically with above 20cm distance from each other d SIM card is out of service or 3G service is not opened e Fail to connect to WiFi Please check the following settings a The SSID encryption type or password are entered incorrectly b AP access point or router works abnormally c No WiFi antenna connected or the antenna is not vertically located e The DVR cannot be accessed via platform iVMS WVS after successful connection to 3G or WiFi Possible reasons a The parameters e g server IP device registered ID etc of the platform are configured incorrectly b The platform works abnormally e Fail to obtain satellite positioning information Possible reasons 62 User Manual of DS 8100HMI STM Series Mobile DVR a The satellite positioning antenna is not placed outdoor b There is no satellite positioning module built in or external available for the DVR c The Position Module are configured incorrectly please see Chapter 6 2 e Why does the device seem unresponsive when operating with the IR remote control Please read Chapter 1 2 and check a The batteries are installed correctly making sure that the polarities of the batteries are no
40. odel serial No firmware version encoding version and panel version 8 2 6 Backup Device Purpose 59 User Manual of DS 8100HMI STM Series Mobile DVR You can view the status and the free space capacity of the USB backup device connected And you can also format the backup device Steps 1 Enter the Backup Device interface as shown in Figure 8 9 Menu gt Maintenance gt Storage Backup Medium Backup Device USB Backup Status Normal Free Space Capacity 1 02GB 1 96GB OK Figure 8 9 Backup Device Interface 2 You can view the status and the free space capacity of the backup device 3 Formatting the backup device 1s also available 8 2 7 Rebooting DVR You can go to the Reboot interface Menu gt Maintenance gt Reboot to reboot the DVR Maintenance E FF FP Upgrade ac Search Default Configuration Attention f Are you sure to reboot now Information Yes NO Figure 8 10 Reboot Interface 60 User Manual of DS 8100HMI STM Series Mobile DVR Appendix Glossary e 3G 3G refers to the 3rd generation telecommunication technology which is the high speed transmission of the cell data The 3G service can transmit sound and other data simultaneously and the bitrate is up to hundreds kbps There are 3 standards for the 3G the CDMA2000 WCDMA and WiMAX e DHCP DHCP is the acronym of Dynamic Host Configuration Protocol and it is one of the TCP IP protocol stacks it is used to assign the dyna
41. put as shown in Figure 7 7 Max 8 time periods can be set within each day You can click Copy to copy the settings to other days Handle Type Arming Schedule Mon 0 24 0 E 0 Y 0 0 0 oot B o y D ee Oe A 4 4 gt di gt db 4 4h ib 4 gt 4 4 gt 4 db 49 4 ib 45 a gt d gt ib dib ib 4 4 459 oboe Rie Fo MO O ES 4 dh ib db db dib 4 459 oD Figure 7 7 Arming Schedule Settings Interface 4 Click Apply and OK button to save and exit 5 Click Apply button in the Alarm Output Settings interface to confirm the settings 7 2 3 Detecting Video Tampering Purpose Trigger alarm when the lens is covered and take alarm response action s Steps 1 Enter the Camera Settings interface and click the Set button for More Setting as shown in Figure 7 8 49 User Manual of DS 8100HMI STM Series Mobile DVR Menu gt Other Settings gt Camera gt Set Advanced Camera Analog 1 Image Settings Set ES 2 Tamper proof Area Settings Handle E Motion Detection E Video Loss Detection Apply OK Cancel Figure 7 8 Tamper Proof Settings Interface 2 Check the Tamper proof checkbox and click the Area Settings button for Tamper proof to set the areas for detecting video tampering Note The alarm can be triggered only when the view of camera is fully blocked Steps 1 Press the Edit key on the remote control and a red block appears on the screen 2 Press the Direction ke
42. r 4 Select the screen you want to set Press Enter key and Direction keys on the remote control to select the channel you want to display Setting an X means the channel will not be displayed Press Enter key to confirm the settings for the current channel Click OK button to save the settings and exit 5 Click the Apply button in the Preview Settings interface to confirm the settings 25 User Manual of DS 8100HMI STM Series Mobile DVR Chapter 3 Record Settings 26 User Manual of DS 8100HMI STM Series Mobile DVR 3 1 Configuring Encoding Parameters 3 1 1 Initializing SD Cards Before recording make sure that the SD card has already been installed If not please install a SD card and initialize it Steps 1 Enter the SD Card Management interface as shown in Figure 3 1 Menu gt SD Card SD Card Management Overwrite Yes SD Card ren OF ET L BL Card 1 Status Normal Free Space Capacity 1 5GB 29 09GB Format OK Cancel Figure 3 1 SD Card Management Interface 2 Select SD card to be initialized If the SD card is installed correctly and formatted the status is normal or sleeping 3 Set the Overwrite to Yes or No Note By default the overwriting function is enabled If you set the Overwrite to No the recording stops when the SD card is full 4 Click the OK button to confirm the settings 3 1 2 Configuring Record Settings Purpose You can configure the transmission stream type the
43. r the record schedule interface as shown in Figure 3 3 1 Select the check box for the Enable Schedule item 2 You can choose the day to which you want to set schedule 3 To schedule an all day recording check the checkbox for the All Day item 4 To arrange other schedule leave the All Day checkbox blank and set the time period 5 The Type can be set as Normal Motion Detection Alarm Motion Alarm Motion amp Alarm Please refer 28 User Manual of DS 8100HMI STM Series Mobile DVR to Chapter 3 2 amp 3 3 for motion and alarm recording 6 Click the OK button to save the settings and exit Note Up to 8 periods can be configured for each day And the time periods can t be overlapped each other You can enter the Record Status interface Menu gt Status gt Record to check the recording status Record Settings E Enable Schedule DET All Week All Day Type Normal Type Normal 10 20 30 40 0 60 70 8 0 0 Type Normal Type Normal Type Normal Type Normal Type Normal Type Normal w ite iam ae iam a ap gt dh dh dh 4 4h 4 4h E i E i E ili F P UP gr II O O Te O E BH EITI EI M gt gP gp gr 4 4h 4 GP Type Normal OK Cancel Figure 3 3 Record Schedule Interface 5 Click the Set button for More Settings to configure the pre record and post record Click the OK button to save the settings and exit Pre record The time you set to record before the scheduled time or event For
44. ratio 10 24 2012 08 35 18 Power On N A Informati 10 24 2012 08 35 18Local SD Card Inf N A e Informati 10 24 2012 08 35 24 Start Record N A 8 Informati 10 24 2012 08 35 24 Start Record N A e Informati 10 24 2012 08 35 24 Start Record N A 8 Informati 10 24 2012 08 35 24 Start Record N A e Informati 10 24 2012 08 35 25 Start Record N A 8 Informati 10 24 2012 08 35 255tart Record N A e Informati 10 24 2012 08 35 25 Start Record N A ts lafa rnant AN OA IMA MA MO AC Fn t Nannreal KIA Details Play Export Cancel Figure 8 5 Log Search Results 4 Click the Details button to view its detailed information Notes 1 Select the log file by pressing the Up and Down keys on the remote control 57 User Manual of DS 8100HMI STM Series Mobile DVR 2 Check the log file by pressing the Enter key on the remote control 5 You can also click the Play button to view the related video files if available 6 If you want to export the log file click the Export button to export the selected one Note Please connect the USB device to DVR before operating log export 8 2 3 Restoring Default Settings Steps 1 Enter the Default interface Menu gt Maintenance gt Default Maintenance w S E Default Settings Upgrade anfiguration System will reboot after restoring factory configuration Continue Information OK Cancel Figure 8 6 Restore Default Settings 2 Click the OK button to start restorin
45. resolution frame rate etc Steps 1 Enter the Record Settings interface as shown in Figure 3 2 Menu gt Basic Settings gt Record 27 User Manual of DS 8100HMI STM Series Mobile DVR Record Settings Camera Analog 1 Encoding Parameters Main Stream Normal Stream Type Video amp Audio Resolution 4CIF BitRate Type Variable Video Quality Medium Frame Rate 25 PAL 30 NTSC Max BitRate Kbps 1792 Schedule Set More Settings Set Copy To w Copy OK Cancel Figure 3 2 Record Settings Interface 2 Select the channel to set the parameters 3 Configure the following settings Encoding Parameters Main Stream Normal Main Stream Event and Sub Stream options are available Main Stream Normal is used for schedule recording Main Stream Event is used for event recording Sub Stream is used for network transmission Stream Type Video and Video Audio options are available Resolution You can choose the resolution for the selected channel Note The resolution of main stream cannot be lower than that of sub stream Bitrate Type Variable and Constant options are available Video Quality If you set the Bitrate Type to Variable you can select the video quality including Highest Higher Medium Low Lower and Lowest Frame Rate You can set the FPS frames per second 1 2 4 6 8 10 12 15 16 18 20 22 and 25 PAL 30 NTSC options are available 4 Click the Set button for Schedule to ente
46. t reversed b The batteries are fresh and are not out of power c The remote sensor is not covered or blocked by other object d There are no fluorescent lamps in use nearby e No backup device is detected when exporting recorded files Possible reasons a There is no backup device connected with the DVR b The DVR and your backup device are not compatible c Initialize the backup device before using d The backup device is damaged 63 0203001030802 First Choice for Security Professionals HANGZHOU HIKVISION DIGITAL TECHNOLOGY CO LTD www hikvision com
47. the CVBS output standard to NTSC or PAL which must be the same with the video input standard e System Time Select the system time e Enable Password Enable disable the requirement of the login password 3 Click the Set button for DST Settings to enter the DST settings interface as shown in Figure 2 4 You can check the Enable DST checkbox and then you choose the date of the DST period After configuration click Apply button to save the settings and click OK button to return to the Display Settings interface 21 User Manual of DS 8100HMI STM Series Mobile DVR Display Settings E Enable DST From Apr To Oct ist Sun v last Sun DST Bias 60 Minutes Y OK TF Cancel Figure 2 4 DST Settings Interface 4 Click the Set button for Advance Setting to enter the advanced display settings interface as shown in Figure 2 5 Display Settings Device Name Device No Brightness of CVBS Menu Transparency Operation Timeout mobileDVR 205 B Non transparent Never OK Cancel Figure 2 5 Advanced Display Settings Interface 5 Configure the following settings e Device Name Edit the name of device e Device No Edit the serial number of device The Device No can be set in the range of 1 255 and the default No is 255 e Brightness of CVBS Adjust the video output brightness e Menu Transparency Adjust the transparency of the menu e Operation Timeout Set timeout time for menu inactivit
48. tput Triggered Camera Set OK Cancel Figure 3 4 Motion Detection 4 Click the Set button for Triggered Camera to select the channel to be triggered 5 After configuration of motion detection enter the Record Settings interface to set motion detection record Please see Chapter 3 1 2 for record settings set the Type to motion detection 30 User Manual of DS 8100HMI STM Series Mobile DVR 3 3 Configuring Alarm Triggered Record Purpose Follow the procedure to configure alarm triggered recording Steps 1 Enter the Alarm Input settings interface as shown in Figure 3 5 Menu gt Other Settings gt AlarmIn Alarm Input Alarm Input No A lt 1 Alarm Name Trigger Level High Level v Trig Record Channel Sef Schedule Handle Type Copy To OK Cancel Figure 3 5 Alarm Input Settings 2 Click the Set button for Trig Record Channel to select the alarm triggered recording channel s Click the Apply button to save the settings and click OK to exit For other alarm input configuration please see Chapter 7 2 1 3 After configuring alarm input enter the Record Settings interface to set alarm triggered record Please see Chapter 3 1 2 for record settings set the Type to alarm motion alarm or motion amp alarm 3 4 Searching Record Files Purpose Search and play back record files by setting the searching restriction of recording type and recording time Steps 1 Enter the Video Search interface as s
49. ttings Interface 2 You can select Position Module check Satellite Time Adjusting and choose Time Zone and Speed Unit There are four options in Position Module including RS232 RS485 Built in and Display Terminal e RS232 Obtain data from the satellite positioning module connected through RS232 interface e RS485 Obtain data from the satellite positioning module connected through RS485 interface e Built in Obtain data from the satellite positioning module built in the Mobile DVR e Display Terminal Obtain data from the intelligent display terminal 3 Input the Speed Limit and set actions to handle speeding Audio Alarm and Trigger Alarm Output are available Please see Chapter 7 2 2 for alarm output configuration 4 You can check the checkbox for Display Channel to display the satellite positioning information on the corresponding channel s Note The channel number varies according to the different devices 5 Click the OK button to save the settings and exit Note You can check the status of satellite positioning in Satellite Positioning Status interface 42 User Manual of DS 8100HMI STM Series Mobile DVR Menu gt Status gt Position 6 3 Configuring G Sensor Purpose G Sensor is used for storing the acceleration information of triaxial directions during driving Before you start You need to connect an external sensor to the device for obtaining and providing the acceleration information of triaxial directions
50. y E g when the timeout time is set to 5 Minutes then the system will exit from the current operation menu to live view screen after 5 minutes of menu inactivity Note It is not recommended to modify the Device No You need to enter the Device No on the remote control every time you use it if you modify the Device No 6 Click the Apply button to save the settings 7 Click the OK button to confirm and return to the Display Settings interface 8 Click the OK button in the Display Settings interface to save the settings 22 User Manual of DS 8100HMI STM Series Mobile DVR 2 4 Configuring Cameras Purpose You can configure the OSD On screen Display settings for the camera including camera name date time etc Steps 1 Enter the Camera Settings interface as shown in Figure 2 6 Menu gt Other Settings gt Camera Camera Settings Camera Analog 1 Camera Name Camera 01 Display Camera Name Wi Display Date a Display Week a Date Format MM DD YYYY v Time Format 24 hour v OSD Property Non transparent amp Not y OSD Position OSD Position More Setting o Set Copy To All w Copy FAP LOK JL Cancel Figure 2 6 Camera Settings Interface Select the camera to configure the OSD settings Edit the Camera Name in the text field Configure the Display Camera Name Display Date and Display Week by clicking the checkbox Select the Date Format Time Format and OSD Property Nn nr BE W N Click the
51. y on the remote control to adjust the position of the red block 3 Press the Enter key on the remote control to save the position of the red block 4 Press the Direction key on the remote control to adjust the size of the block and press Enter key to save the setting Note You can press the A button on the remote control to clear the area 5 Press the Menu key on the remote control to set sensitivity including Low Medium and High Click the OK button to save and exit 6 Press the ESC key on the remote control to exit 3 Click the Handle button for Tamper proof to set arming schedule and alarm response action s as shown in Figure 7 9 Alarm response actions e Pop up Image on Monitor When an alarm is triggered the local monitor displays full screen video image from the alarming channel configured for full screen monitoring e Audio Warning Trigger an audible beep when an alarm is detected e Trigger Alarm Output Trigger an alarm output when an alarm is triggered Please refer to Chapter 7 2 2 for alarm output settings 50 User Manual of DS 8100HMI STM Series Mobile DVR Exception Handle Arming Schedule Mon 1 0S 0s 24 5 00 207m 0 0 6 Om 0 3 Ome O E 7 OS 0 4 USO Y 8 Om 0 Copy To All Week E Pop up Image on Monitor E Audio Warning gt 4 4 gt co ME ce ice a gt O oP oP gt 4 4 4 gt 4 SF cS GS S w ae ae g e TO lt All1 2 E Trigger Alarm Output OK Cancel
Download Pdf Manuals
Related Search