ceriatone ots 20w mini manual
Contents
1. e e ef o e e e MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT On the front panel of the Overtone Special you can see fourteen items of interest From left to right 1 POWER two way toggle switch 2 STANDBY two way toggle switch 3 INDICATOR LED 4 PRESENCE control 9 MASTER control 6 RATIO control 7 LEVEL control 8 BASS control 9 MIDDLE control 10 TREBLE control 11 ROCK JAZZ two way toggle switch 12 MID BOOST two way toggle switch 13 VOLUME PULL BRIGHT control 14 INPUT 4 instrument jack POWER two way toggle switch powers the OTS on and off With the toggle switch in the UP position the OTS is ON In the DOWN position the OTS is OFF STANDBY applies high voltage to the vacuum tube anodes and screen grids during use of the OTS To ensure long tube life first power the unit on with the toggle switch in STANDBY position for approximately 30 seconds Then place switch upward to ON position to use the OTS With the toggle switch in the UP position the OTS is in operate mode In the DOWN position the OTS is in standby mode INDICATOR will illuminate when the OTS is powered by turning the rear panel MAINS toggle switch to the ON position If INDICATOR does not turn on check your power cable connections and then the 2A slow blow fuse on the rear of the unit PRESENCE adjusts the high frequency response of the power2. 0 35A 38 58 SELECTOR MAGE IN EELAMNTAN From left to right V1 12AXTIECC83 clean and overdrive stages 1 and 2 V2 12AX7 ECC83 overdrive stages and 4 V3 12AX7 ECC83 phase inverter for power amplifier V4 6V6 V5 6V6 d 1 J In these pictures we have color coded the important features for simplicity 1 Blue arrow bias adjustment potentiometer shaft 2 Yellow arrow power tube pin connected to 1 Ohm bias measurement resistor 3 Red arrow ground pin connected to 1 Ohm bias measurement resistor NOTE each power tube socket has a 1 Ohm bias measurement resistor connected to a ground pin near the rear of the chassis To measure your power tube bias carefully follow these steps with the amplifier in OPERATE MASTER at minimum and connected to a speaker load not doing so may damage your amplifier 1 Turn on a digital multimeter DMM and set it to read millivolts mV in the 100mV range this will vary from DMM to DMM 2 Plug a black probe into the color coded jack on your DMM and do the same for a red probe 3 Touch the black probe tip to the ground pin connected to the 1 Ohm bias measurement resistor red arrow This is GROUND in the OTS amplifier u J 4 Touch the red probe tip to the power tube pin connected to the 1 Ohm bias measurement resistor yellow arrow on the far left This measures bias for the 6V6 in that socket position Right down the valu
3. 20W Mini Lunchbox Amplifier User s Manual Thank you for the purchase of your Ceriatone Overtone Special 20W Mini guitar amplifier Here we hope to explain how best to use your new amp Table of Contents TD FROOUL TIS OVERS sspe dd MC P seasons eut aves att debt Pb tata ta E page 2 By ONG eS T page 3 SM roues EI 4 a ear Tr AIMCO page 9 Tube compliment and bias 5 page 10 6 Frequently Asked 5 page 14 de ad US 17 1 About the Overtone Special 20W Mini Lunchbox The release of our Overtone series of amplifiers has been overwhelmingly popular and the support of customers such as you has instigated the release of over a dozen different versions within the series We have been pleased to provide many players access to our unique take on these legendary amplifiers Most recently we offered our first foray into the lunchbox format the OTS Mini 20W Not only is this amplifier a completely different format for us it is also a unique design that capitalizes on the expressive sweet power section centered on classic American style 6V6 tubes Many fantastic sounds are possible with this unassuming but completely serious amplifier While our work could
4. Klein ulator into this jack using 74 instrument cable The effects loop in the OTS amplifiers are all passive like the originals IMPEDANCE three way rotary selector Set this selector to the position that matches the impedance of your speaker cabinet NOTE if you are using two speaker cabinets in parallel ex two 16 Ohm cabinets set the impedance selector to half that of a single cabinet in this case 8 Ohms SPEAKERS EXTENSION AND MAIN 74 speaker cable jacks Use a 1 4 speaker cable to connect your speaker cabinet to the amplifier using these jacks If you use one speaker cabinet use the jack labeled MAIN If you want to run two cabinets in parallel connect the second cabinet to the amplifier using the jack labeled EXTENSION NOTE never turn your amplifier to OPERATE mode without connecting the amplifier to a speaker cabinet or suitable dummy load Failing to do so may damage your amplifier HT FUSE 0 5A slow blow fuse used to protect your amplifier particularly during the event of tube failure Replace only when necessary MAINS FUSE 2A slow blow fuse used to protect your amplifier from voltage spikes or excessive current draw Replace only when necessary A C MAINS IEC cable inlet plug a suitable IEC power cable into this inlet to power your amplifier 9 TUBE COMPLIMENT AND BIAS ADJUSTMENT fuse MAING FUSE POOT PIDAL OD TRIM WFFECTS LOOP IMPLOANCE e OG A MAG
5. Stage 2 ROCK JAZZ BRIGHT MID BOOST PAB OD TRIM OD Stage 3 OD Stage 4 16 7 Settings templates Ceriatone OTS MINI 20 ROCK JAZZ ON _ INPUT e e P iin rs n T s Z6 9 Gs Pr oS E 58 3 1 6 C e Coe Ce Oe Oe Oe Ce Cove 2 Ce f a mecs See MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT Ceri Q tuaGtene OTS MINI 20 ROCK JAZZ ON p INPUT e e zm y s dh CC dm T i 7 us N J X MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT Ceri Q tuaGteng OTS MINI 20 ROCK JAZZ ON p INPUT e e o g 5 Pin ER a ON yo N Fe diia K 07 C C OC eC 6 8 6 CeCe Coe CeCe 9 Ce MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT f 17 J e Ceriatone OTS MINI 20 ROCK IAZZ ON S C C ee e e e eo e o e_ 2 Ce MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT Ceri Q tuatene OTS MINI 20 ROCK JAZZ ON _ INPUT e e e fea fs P ines fi ss ETT Pm 24 77398 ATTS yo C C C eC e Cpe o
6. amplifier using negative feedback Use this control to add sparkle and clarity to your tone MASTER sets the overall volume of your amplifier RATIO serves a sort of volume control for the overdrive channel However just like this version of the original amplifier there are not individual master volume controls for the clean and overdrive channels Instead the RATIO control serves to balance out the volume of the overdrive channel with the clean channel LEVEL adjusts the amount of gain and in turn distortion in the overdrive mode BASS adjusts low frequencies in your amplifier for both clean and overdrive modes MIDRANGE adjusts the mid frequency response for both clean and overdrive modes TREBLE adjusts the high frequency response for both clean and overdrive modes At near maximum settings you may also notice an increase in gain ROCK JAZZ adjusts the overall frequency response and voicing of the amplifier ROCK has a fatter midrange and a deeper spongier bottom end You might find ROCK more familiar territory JAZZ tightens up the bottom end and adjusts the contour of the midrange giving the amplifier more of a hi fi response Experiment with both as great sounds rest in each With the toggle switch in the UP position ROCK is on In the DOWN position JAZZ is on MID BOOST is a midrange frequency boost You can use this to add fatness to your clean or overdrive tones or even make single coil guitars sound thicker and less scoope
7. eoe o o o _ e Jj MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT Ceri ezlatone OTS MINI 20 HOCK JAZZ ON 9 e C Lu e gt 7 Se a E E d E 2 MID BOOST POWER STANDBY PRESENCE MASTER RATIO LEVEL BASS MIDDLE TREBLE VOLUME pull BRIGHT i 18 J
8. AIN 1 4 speaker jack HT FUSE 0 5A slow blow fuse MAINS FUSE 2A slow blow fuse 0 1 2 3 4 5 6 T 8 9 10 A C MAINS IEC cable inlet FOOT PEDAL 5 pin DIN female jack is used to connect the foot pedal to the amplifier Use the foot pedal to control the OVERDRIVE and PREAMP BOOST modes Red LED indicates OVERDRIVE and Green LED indicates PREAMP BOOST OD TRIM control This control adjusts the signal strength sent to the first tube stable in the OVERDRIVE channel Lower settings yield more touch sensitive lower gain sounds Higher settings are more compressed higher gain and more harmonically complex Start with the control between 10 00 and 12 00 clock face but experiment for your own ideal tone EFFECTS LOOP SEND 7 instrument jack can be used to directly interface the preamp of the OTS thereby bypassing the power amplifier and using the OTS as a preamp Conversely this is usually used as the SEND of the effects loop Plug the input of your effects unit or interface device ex C lator Klein ulator into this jack using 74 instrument cable The effects loop in the OTS amplifiers are all passive like the originals EFFECTS LOOP RETURN 7 instrument jack can be used to directly interface the power amp of the OTS thereby bypassing the preamp and using the amplifier as a power amplifier Conversely this is usually used as the RETURN of the effects loop Plug the output of your effects unit or interface device ex C lator
9. an overloading of the effect unit itself Most rack mount units have different input impedance than pedals and thus can sometimes function fine without a buffer before them In addition some of these rack mounted effects can pad the volume they receive preventing it from overloading Pedals do not have proper input impedance or padding ability and therefore do not play nicely For best results an effects loop interface like the C lator or Klein ulator should be used with the OTS amplifiers These units prevent impedance mismatching as well as provide the ability to pad down the volume sent to the effects units hence preventing any overloading Can substitute different tube types for the 12AX ECC83s 6V6s Although you can try 12AT7s 12 075 57515 without any harm the design is optimized for 12AX s and are therefore the only recommended tube in the preamp positions Usage of other power tubes is not recommended for the OTS 20W Mini What settings do you recommend Try setting all controls at 12 00 and adjust MASTER to a suitable volume 14 read about something called a PI trimmer inside of the amp Does the OTS Mini have it No we omitted it from this design for simplicity Do need to use matched power tubes Although not necessary matched power tube sets are recommended for best results Do need to use a matched and balanced phase inverter tis not necessary Feel free to experiment with different tube
10. d We particularly like MID BOOST with the overdrive mode With the toggle switch in the UP position MID BOOST is on In the DOWN position MID BOOST is off VOLUME adjusts the signal strength coming out of the tonestack and going into the second tube stage Think of this as a gain control primarily for your clean channel but note it will impact the overdrive mode as well BRIGHT is a high frequency boost that can be used to add sparkle to your tone in both clean and overdrive modes This high frequency boost is more prominent as VOLUME is turned down To engage this feature pull out the VOLUME control To turn BRIGHT off push the VOLUME control inward INPUT jack provides a typical 1megaohm input impedance as seen on most guitar amplifiers The FET input has been removed from the 20W Mini as in most circumstances the regular input provides the best results in clean and overdrive modes 4 REAR PANEL CONTROLS FOOT PEDAL OD TRIM EFFECTS LOOP IMPEDANCE SPEAKERS 8 SEND RETURN EXTENSI ON MAIN PREAMP POWER AMP OUTPUT 3 INPUT SELECTOR HT FUSE MAINS FUSE 0 5A SB 2A SB A C MAINS MADE IN KELANTAN On the rear panel of the Overtone Special you can see ten items of interest FOOT PEDAL 5 pin DIN female jack OD TRIM control EFFECTS LOOP SEND 7 instrument jack EFFECTS LOOP RETURN instrument jack IMPEDANCE three way rotary selector SPEAKERS EXTENTION 7 speaker jack SPEAKERS M
11. e your DMM reads You might expect a value between 23mV and 25mV 9 Repeat for the other power tube position Okay now I ve measured my bias Now what To calculate bias there are two pieces of information you need to know your amplifier s power tube plate voltage and the published value for maximum plate dissipation for the power tubes used in your amplifier To save you some time and energy here are those two values 380 390VDC 14W Approximate plate voltage for OTS Mini amplifiers Maximum plate dissipation for 6V6s and now some math The formula for calculating bias is as follows maximum plate dissipation VM x percent of maximum dissipation x 1000 bias current mA amplifier plate voltage In most cases amplifiers are biased between 50 and 75 dissipation We bias the OTS to approximately 23mV 25mV reading on a DMM An example is as follows 14W X 06 x1 24mA 380V DC 65 000 about 24m 12 You might wonder why your DMM is set to millivolts and not milliamps simply we have a 1 Ohm resistor placed between your probe jacks and ground to convert a current reading to a voltage reading That way a bias current of 24mA measures as 24mV on your DMM NOTE Only set your DMM to mV for measuring bias on the OTS amplifiers Not doing so may damage your DMM Now that you know how to calculate bias all you need to do is 1 Follow steps 1 5 on page 11 2 Calcula
12. not have been possible without the gracious information shared over the last decade in the public domain we hope you appreciate our modifications component selection and construction techniques Most of all we hope the OTS becomes an integral part of your tone equation to exhilarate your playing and music Rock on Azam 2 QUICK SETUP for instant gratification 1 Plug your guitar using a 1 4 instrument cable into the INPUT on the far right of the front panel 2 Plug a suitable power cable from the OTS s rear panel MAINS cable inlet to your wall power receptacle 3 Plug the OTS into your speaker cabinet using 1 4 speaker cable 4 Setthe IMPEDENCE selector to the match the impedance of your speaker cabinet 9 Plug the footswitch cable into the FOOT PEDAL jack on the rear panel of the amplifier 6 Set the OD TRIM control on the rear panel to 12 00 clock face 7 Setall rotary controls on the front panel to 12 00 clock face 8 Turn MASTER control to about 9 00 clock face 9 Set front panel MID BOOST switch in the down position OFF 10 Set front panel ROCK JAZZ switch in the up position ROCK 11 Set front panel POWER switch in the upward ON position with adjacent switch to STANDBY for 30 seconds to allow tube filaments to warm up 12 Set front panel STANDBY switch upward to the ON position 13 ROCK f 3 J 3 FRONT PANEL CONTROLS e Ceriatone OTS MINI 20 hocK IAZ ON _ INPUT
13. s of the same type in your OTS though read that the components used in this type of amplifier are really important What is inside my OTS Mini We use a combination of parts custom made for us to our specifications power transformer output transformer choke high temperature low ESR electrolytic capacitors and those used in the original amplifiers Vishay Dale RN65 precision metal film resistors 1W carbon film resistors SBE 6PS polyester film capacitors high quality ceramic disc capacitors Belton tube sockets and Alpha potentiometers We prefer high quality enclosed Cliff built in the UK jacks to the open style Switchcraft jacks used in the originals and many clones Finally we occasionally use NOS components from our vast surplus parts collection in locations they work well and complement the voicing or enhance the performance of the amplifier like to use rack mounted multieffects units What is the output level straight from the EFFECTS LOOP SEND jack 10dB or 408 While not exact 10dB is a better approximation than 4dB The actual output level will depend on your settings particularly the volume controls 4dB is usually reserved for recording P A equipment with balanced connections 15 This all seems kind of complicated can you tell me where all of these controls are in the preamp so have a better idea how to set up my amplifier Clean and OD Stage 1 Tonestack Input Vol Clean and FX Loop OD
14. te what bias voltage reading you will set your tubes to in this case we will use 24mV 3 Place your red probe on the previously mentioned power tube pin connected to the 1 Ohm resistor and the black probe on the other end of the 1 Ohm resistor 4 Turn the bias potentiometer shaft SLOWLY until your DMM reads 24mV 9 Wait 1 minute 6 Recheck all power tube bias measurements 7 Readjust bias potentiometer shaft if necessary A FEW COMMENTS ON BIASING Due to the nature of vacuum tube amplification there are inherent risks when biasing your amplifier Extremely high voltages are present and vacuum tubes reach high temperatures during use The risk of electrical shock and or skin burns should ALWAYS be kept in mind Therefore bias at your own risk and only while paying attention and taking all precautionary measures Biasing should only be done on a clean workbench with no distractions Do not wear loose clothing or any jewelry Take your time and think carefully before each step Again bias at your own risk Ceriatone Amplification is not responsible for any damages or injuries resulting from user biasing 13 6 FREQUENTLY ASKED QUESTIONS How do I hook up this thing Section 2 beginning on page 3 When plug effects into the effects loop my tone noticeably changes Sometimes the effects don t sound quite right What s the deal Generally what you re hearing is a significant mismatching of impedances and or
Download Pdf Manuals
Related Search