Solar charge controller User manual
Contents
1. Solar charge controller User manual EPOW Ksxx Series V1 9 Brand MOBOLO Product model EPOW KS10 EPOW KS20 EPOW KS10H EPOW KS20H Product Description EPOW KSxx This series of controllers for solar street lights solar photovoltaic system design the use of a dedicated MCU chip intelligent controller the user interface is simple Has a series of protective measures such as overcharge over discharge short circuit overload to prevent the opposite direction to connect the wires can automatically restore to a working state Intuitive charge and discharge status battery status load working status and fault indication Sampled by the smart chip on the battery voltage discharge current and ambient temperature related to the parameters of the battery capacity battery characteristics through a dedicated control of the model algorithm discharge rate temperature compensation correction efficient high accuracy control High efficiency PWM charge mode effectively reducing the battery plate curing greatly extending battery life Variety of light control switch delay half power output mode in two time periods control automatic identification of operating voltage and satisfy customer a wide variety of application needs Solar cells E Output Protection Tvs Power Drive Power Drive Output 2 P eooo a 2 li I Functional characteristics Use of smart chips and proprietary control so2. e 9 24V Over discharge voltage 11 8 V x2 24V Control mode PWM pulse width modulation Note the company reserves the right to change without prior notice
3. the battery voltage up to resuming voltage will automatically output status indicator light 2 into orange on Note in optical delay mode a discharge and cut off because of the protection of load in the evening is not restart load avoid load appear flashing phenomenon Load instructions when load startup the load indicator light 3 on If the indicator light 3 for slow flicker said output overload load current more than 1 25 times of rated current controller or 1 5 times overload protection start time were 10 seconds or 1 second controller will be forced to shut down output When load appear when the fault controller will cut off output in the us in 8us indicator light 3 rapid flicker Protection is started the controller delay after 30s will try to reconnect the load if short circuit or overload troubleshooting later start load output V Work mode Settings Mode setting method press light touch buttons for 3 seconds mode display window after flicker loosen the button each as a convert a code until the selected code that stop button stop flicker in 5 seconds later set to be automatically save LED in 3 seconds out after save electric energy Light control mode the night comes light below the substrate start signal controller in delay confirmation after 10 seconds start load Light control mode the night comes light below the substrate start signal controller in delay confirmation after 10 seconds start load Ligh
4. ftware based expert systems intelligent optimization of SOC control A variety of light control light control time delay the half power and two time periods separately control mode and automatic voltage recognition feature the maximum to meet the complex and changeable by the user application requirements Three level overload protection short circuit protection Have the charging discharge reverse connect protection function repair the system in fault will be back to the work of the state not causing damage to any component will not burned the fuse Sampling the battery voltage discharge current temperature etc related to the parameters of the battery capacity combined with a dedicated control algorithm to achieve the rate of discharge of the battery characteristics high efficiency and high accuracy control of temperature compensation correction Adopted PWM tandem charge control the charging efficiency of 3 6 increase in generating capacity reduce heat and greatly improve system reliability extend battery life Storage battery temperature compensation function Characteristics of the battery discharge rate correction Detailed report of the module damage warning charging quantity instructions shows the battery storage state and load all function by pressing a button easy to use the function is Strong Using industrial grade chips normal operation in the cold hot humid environment With large diameter interval
5. greater connection pillars can install 6 mm square wire enhance the conductive insulating performance and reliability SMT production process gold plated PCB industrial grade chips advanced technology quality assurance II Operation interface Solar cells charging indicator _Working mode display Towches switch Battery status Settings indicator Load status indicator Solar cells Battery Load III Installation and use IV Wire ready suggest using more shares TongXin insulation wire wire length decrease as far as possible especially the connection between the battery and controller reduce electric loss Choose less than 4 A square millimeter of current density of the cross sectional area of the TongXin wires To connect the controller battery terminals then will the other end even to the battery pay attention to the positive and negative If the connection is correct indicator light 2 light Otherwise need to check the connection If there is a reverse connect will not burned fuse and damage the controller to any component Connect the leads of the solar cells first connect the controller of solar panels on the interface again will also connects to the solar battery please pay attention to the anode and cathode the light is enough charging indicator light is on Otherwise need to check it right connection Load connection will be connected to the controller of the l
6. hours 3 hour at full power 5 Delay off after 7 hours 3 5 hour at full power Delay off after 8hours 4 hour at full power Delay off after 9 hours 4 5 hour at full power Delay off after 10 hours 5 hour at full power a ea Delay off after 11 hours 5 hour at full power pg Delay off after 12 hours 5 hour at full power gg Delay off after 13 hours 5 hour at full power pg Light control switch 5 hours at full power VII Technology index MODEL EPOW KS10H EPOW KS20H OA The system voltage 24V 12V AUTO 1 25 times the rated current the overload protection is 10 seconds Overload short circuit 1 5 times the rated current the overload is 1 second protection greater than three times the rated current Sus short circuit protection a a Industrial level 35 C 55 C working Temperature Enhance the charging 14 5V x2 24V Maintenance time 30min voltage Only when seen called when the discharge Straight ChongChongDian 14 2V x2 24V Maintenance time 30min Float charging voltage Charging to return to voltage 13 2v x2 24V Temperature 5mv C 2V Promotion direct charge float charge to return the voltage compensation compensation Undervoltage voltage 11 2V x2 24V Over discharge voltage 13 7V x2 24V Maintenance time To return to action until charging voltage 10 5V Discharge rate of initial discharge compensation fixed voltage no load voltage x2
7. oad output port pay attention to the anode and cathode some load is no reverse connect to answer the protection function Use instructions Charging and overpressure instructions when the system connection was correct and sufficient sunlight charge start charging indicator light 1 for the green LED on Battery batteries will be shut down after charging and charging flicker Charging process is using PWM charging mode if happened discharge first you have to charge voltage ascension and keep 10 minutes and then down to fill continuously voltage keep 10 minutes activate the battery avoid vulcanization crystallization finally to float charging pressure and keep the float charging pressure If not happened discharge won t appear ascension way of charging prevent battery water loss The automatic control process will make the battery charge efficiency and to ensure the best and to extend the service life of it Battery state directions the battery voltage in the normal range the state indicator 2 as the green LED on Battery full for green LED flicker When the battery power to half of the time indicator for orange LEd on When the battery voltage continue to reduce to owe pressure for red LED on At this time the system banned start load but has begun will maintain load output if the voltage further reduce to put voltage red flicker in order to protect the battery controller will be forced to shut down output When
8. t than high substrate the output signal controller in close after 1 minute delay confirmation close the output load stop working Light control delay mode Start the process with reference to the light control mode load startup shut down automatically in work after period of time save the energy consumption reference model table set delay time Light control mode delay half power 21 34 mode starting up process and a same load startup it started the whole power output and the work after a period of time is half the output power to save electric energy To delay time after the end shut off the output Manual control mode this mode of the load by the user manual control but still got the overload and discharge control logic of the restrictions start up and shut down the load method is mode LED to stop flicker quick touch Settings button open the control load switch Debug mode used for debugging systems use canceled day or night intelligent identification of light and other control mode is the same Light is bright closed at output load No light start load at output installation debugging checked more convenient VI Work mode setting chart Delay off after 1 hour 0 5 hours at full power Delay off after 2 hours 1 hour at full power Delay off after 3 hours 1 5 hour at full power Delay off after 4 hours 2 hour at full power Delay off after 5 hours 2 5 hour at full power 5 14 Delay off after 6
Download Pdf Manuals
Related Search