User Manual User Manual
Contents
1. is plugged in it will begin to fill It will automatically stop when the water has reached the proper level 3 Turn Off On toggle switch on the rear to the On up position 4 Allow the dispenser to reach the proper temperature This will occur in approximately 20 minutes The green pilot light will come on when the unit is ready 5 Place an empty cup or container directly under the faucet and pull faucet handle towards you When finished release the handle Note Due to water expansion during initial heat up on installation excess water may flow from the drain spout Plumber s instructions Water inlet j gm Filing iP i Shut Off InDooming Valve Water Supply Plumbing Connection Diagram Fig 1 www AvantcoEquipment com 3 EQUIPMENT User Manual VANTCO Cleaning Regular cleaning ensures long life For dirt or smudges on the dispenser s exterior a damp cloth will suffice If necessary a non corrosive non abrasive detergent or cleaner may be used Be sure to unplug the appliance before cleaning 1 Turn the off on toggle switch off unplug and allow to cool before cleaning 2 Do not use abrasive or harsh cleaners as they may damage the finish of this dispenser 3 Only those persons trained and qualified in equipment repair should attempt to open and clean the inside of this dispenser Resetting the Hi Limit Thermostat 1 Turn off on toggle switch off unplug and allow the dispenser to cool befor2. missing parts 1 Place hot water dispenser on sturdy level heat resistant non flammable surface near power supply and water supply Do not connect water line or power cord at this time 2 Form three coils of 1 4 O D copper tubing or high pressure flexible hose not supplied and connect to the cold water line The coils allow the dispenser to be moved easily for cleaning and servicing Flush incoming water in the line See diagram Fig 1 Note Itis recommended that an optional shut off valve and water filter be installed on the water line at this time 3 Attach the water line to the water inlet fitting located on the rear of the dispenser Hold the dispenser water inlet fitting with a wrench when tightening the water line 4 Turn on water supply 5 Check for water leaks at water inlet Tighten fittings if necessary 6 Connect power supply cord into proper power supply as indicated on electrical nameplate Note This dispenser is designed to operate with a water pressure between 30 to 80PSI When water pressure exceeds 80PSI it is recommended that an optional water pressure regulator be installed to reduce water pressure to 50 PSI For installation of less than 25 feet use 1 4 O D copper tubing For installation of more than 25 feet use 3 8 O D copper tubing and use and adapter for connection as necessary Operation 1 Ensure the Off On toggle switch on back of unit is in the off down position 2 As soon as the unit
3. AVANTCO User Manual 3 T O ar O lt lt e e a OO Hot Water Dispenser User Manual Model HWD 15 Please read and keep these instructions Indoor use only www AvantcoEquipment com EQUIPMENT User Manual VANTCO Specifications Model HWD 15 Electrical 1450W 12 0A Water Capacity 5 6 liters Parts Diagram 1 Power Lamp 2 Indicator Hot Water Ready 3 Faucet C J 4 Outlet Overflow Steam 5 Drain Plate _ ee 4 2 E e AN Read and understand all instructions before using the appliance CAUTION HOT SURFACE Warnings e This appliance is designed for commercial use only e This appliance must be placed on a level surface able to adequately support its weight e Never immerse the appliance in water e Do not unplug the appliance if your hands are wet e Do not unplug the appliance by pulling the cord e Do not attempt to repair or replace the power cord if itbecomes damaged Contact a qualified service agent e While the appliance is in use some parts will become very hot Ensure that the cord does not come in contact with any hot parts e Be careful not to touch any hot surfaces e Make sure the Tank Heater Switch is off located at bottom rear side before connecting to the power supply 2 www AvantcoEquipment com EQUIPMENT VANTCO User Manual Installation Carefully unpack the hot water dispenser and inspect for damage and
4. e servicing 2 Remove the rear cover and push the red reset button 3 Replace Snap Plug connect the power supply cord and turn ON the Off On toggle switch Allow the Dispenser to reach proper temperature AN Under no circumstance should the hi limit thermostat be bypassed In the event of failure the hi limit thermostat should be replaced Adjusting The Thermostat 1 Turn the off on toggle switch off unplug and allow the dispenser to cool before servicing 2 Remove the rear cover 3 Locate the thermostat turn the thermostat adjustment screw Do not adjust more than 1 8 of a turn at a time fig 2 4 Turn screw clockwise to increase the temperature and counter clockwise to reduce the temperature Fig 3 5 Replace the rear cover connect the power supplycord and turn the off on toggle switch on 6 Allow the dispenser to reach full temperature before checking the water temperature To assure the ideal temperature of 190 F 88 C to 205 F 96 C measure the temperature directly under the faucet 7 If the water temperature is still not within the proper range repeat adjustment steps again until the proper temperature is reached These adjustments should be performed during installation only Operators should refer to the operating instructions only THERMOSTAT 4 www AvantcoEquipment com EQUIPMENT User Manual VANTCO Limited 6 Month Warranty All equipment which is sold under the AVANTCO trade
5. mark and used for commercial purposes is warranted against defects in materials and workmanship The warranty runs for 6 months from the date of purchase and is for the benefit of the original purchaser only All other Warranties Expressed or Implied Statutory or Otherwise including Without Limitation any implied Warranty of Merchantability or Fitness for Purposes are excluded The Seller shall in no event be liable for direct indirect or consequential damages in connection with AVANTCO commercial products This warranty is not effective if damage occurs because of accident carelessness improper installation lack of proper set up supervision when required of if the equipment is installed or operated in any manner contrary to the installation and operating instructions www AvantcoEquipment com 5
Download Pdf Manuals
Related Search