FCC Certifications This Equipment has been tested and found
Contents
1. 1 4 The Rear Panel The rear panel of the switch is shown as below 2 Installing 24 Fast Ethernet Web Smart Switch This switch can be placed directly on your desktop or mounted in a rack Users can immediately use most of the features simply by attaching the cables and turning the power on 2 1 Desktop Installation For desktop installation the switch needs to put on a clean flat desk or table close to a power outlet Plug in all network cables and the power cord then the system is ready Before installing the switch you must ensure 1 Itis accessible and cables can be connected easily 2 Cabling is away from Sources of electrical noise such as radios transmitters and broadband amplifiers x Power lines and fluorescent lighting fixtures 3 Keep water or moisture off 4 Airflow around the unit and through the vents in the side of the case Is great for heat radiation company recommend that you provide a minimum of 25 mm clearance To prolong the operational life of your units 1 Never stack unit more than eight sets high if freestanding 2 Do notplace objects on top of any unit or stack 3 Do notobstruct any vents at the sides of the case 2 2Rack mountInstallation The switch may standalone or may be mounted in a standard 19 inch equipment rack Rack mounting produces an orderly installation when you have a number of related network devices The switch is supplied with rack mounting brackets2. FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning C This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest informati
3. Deskied SRL x t Enable C Enable 2 Ci Dinbi 1O H w Lahti i Disable Enable or i D Enable 1 eine OF ow BON w ET O Disable Y Disable i Enable WORN 5L2Kbpo se Enable 2 Disable 12 Dabla 5 Enable Feil a IMi we A Enabte C Drabble E Disable Enable i C3 Enable mosperel we IME w F Disable pitti par t Dapable g Enable Ait apeerd w dhii w 0 Enable Disable to Digable Items Functions Admin Enable or Disable the Admin function Bandwidth To control the bandwidth you can select the speed limitation you need in the drop list ee Disable 128K 256K 512K 1M 2M 4M 8Mbps _ Operate mode Choose the Speed mode of port 10 100 Half Full If you set to auto speed it will be auto negotiation Auto Speed 10M half 10M full 100M half 100M full Flow Control Enable or Disable the Flow control Link Status To show the status of each port When it s green it means the connection is down Otherwise it s red To save the configuration of the system click apply to save To see the latest Status of port click refresh button 12 3 2 3 VLANS VLANS Configuration is for dividing the LAN into subnet groups for better network management 24 VLAN groups total Mode 1 Disable Turn off the VLAN function by selecting the mode 2 Port BASE Group the port you select by entering the group number Ex 1 in VLAN textbox and selecting the port numbers Ex 1 2 3 4 you want But
4. the device can be managed through console port or web based UI This is much useful for system manager to monitor and control the system efficiently Store and forward switching mode promises the low latency plus eliminates all the network errors including runt and CRC error packets To work under full duplex mode transmission and reception of the frames can occur Simultaneously without causing collisions as well as double the network bandwidth The switch is plug n play without any software to configure and also fully compliant with all Kinds of network protocols Moreover the rich diagnostic LEDs on the front panel provide the operating status of individual port and whole system 1 2 Key Features 24 fixed 10 100Mbps Fast Ethernet ports for easy network connecting application Provide Auto discovery Function for easy Network management Provide 8K MAC address entries and 24 groups VLAN table Support up to 4 ports and 6 groups port aggregation Supports 3 types of QoS priority for port base 802 1p amp TCP IP TOS DiftServ DS priority field Support full duplex flow control and half duplex back pressure Store and forward forwarding scheme Error packet filtering Supports 320K bytes buffer Memory Support local Console port or Web based UI for configuration Internal switching power supply 100 240Vac 50 60Hz 1 3 The Front Panel The front panel of the switch is shown as below hohoho dadhi OOO SVS See Ver
5. E E E 15 3L DISCOV IY ean EAE 16 SE Cla E E A E E ES 17 JOR DOO ee E 17 4 Product SPECINCAUONS isisisisiianissananininnainna 18 Unpacking Information Thank you for purchasing the 24 port Fast Ethernet Web Smart Switch Before you start please check all the contents of this package The product package should include the following Fa Re b h Ghee daii S666 400 dade l F959 vues PPPE e 1 One 24 port Fast Ethernet Web Smart Switch 2 One power cord 3 Rubber foot and screws 4 Rack mount brackets 5 One RS 232 Cable Optional 6 One CD ROM for user s manual 7 One Quick Installation Guide 1 Introduction to 24 port Fast Ethernet Web Smart Switch 1 1 General Description The device is a 24 port 10 100Mbps Ethernet Web Smart Switch Compare to the traditional 10 100Mbps Ethernet the switch delivers a dedicated Fast Ethernet connection to every attached client with no congestion issue The NWay auto negotiation operation automatically negotiates with the connected partners on the network speed and duplex mode that provides an easy way to integrate 10 100Mbps networks with no pain It Is ideal for micro segmenting large networks into smaller connected subnets for improved performance enabling the bandwidth demanding multimedia and imaging applications Out of the ordinary dumb switches the 24 port Fast Ethernet Web Smart Switch embedded advanced management capability that
6. and screws These are used for rack mounting the unit R ack Mounting the Switch in the 19 inch rack 1 Disconnect all cables from the switch before continuing 2 Place the unit the right way up on a hard flat surface with the front facing toward you 3 Locate a mounting bracket over the mounting holes on one side of the unit 4 Insert the screws and fully tighten with a suitable screwdriver 6 5 Repeat the two previous steps for the other side of the unit 6 Insert the unit into the 19 rack and secure with suitable screws not provided 7 Reconnect all cables 2 3 Installing Network Cables Station Connections Reference to the wiring statement of the previous section connect each Station to the switch with correct type of cables Switch to Switch Connections In making a switch to switch connection use every ports to connect another switch or backbone Is strongly recommended The Fast Ethernet ports provide the fat pipe to the server or backbone connectivity for boosting the total system performance Reference to the wiring statement of the previous section connect each station to the switch with correct type of cables 2 4 Network Application LELEL 100Mbps File Server 200Mbps Web Server 3 Management guide This section instructs you how to enter and set up the configurations which can be accessed by RS 232 serial port out of band on the rear panel or by Telne
7. e Port Operation There are 24 100Mbps RJ 45 copper ports on the front panel The auto negotiation feature of the switch allows each port of the device running at one of the following operation modes Half Duplex r r ee me eur All ports supports MDI MDI X auto crossover capability that is the port can connect either the PC or hub without crossover cable adjustment Wiring for 10 100Mbps Copper Following are the summaries of cabling required Media Speed Wiring 10Mbps iCategory 3 4 5 UTP STP 10 100Mbps copper 100Mbps Catego rySUTP STP LEDs Definition The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system Power LED This indicator lights green when the switch is receiving power otherwise it is off Port LEDs Every RJ 45 port on the front panel relevant one LED 10 100Mps for indicating the connection speed and activity status Port LED summary table 10 100M Steady green Connected as 10 100Mbps Blinking green The portis transmitting receiving data If the port is connected but the Port LED is dark check the following items The switch and the connected device s power are on or not The connecting cable is good and with correct type The cable is firmly seated in its connectors in the switch and in the associated device The connecting device including any network adapter is well installed and functioning
8. ip system natrie delete l 10 1 1 1 24FE Start sw 5 ea eala 24FE Smart SW P 5 10 1 1 4 24FE Smart SW 16 3 2 7 Default To restore to default values 1 Click the default button on the Home page 2 Click Apply to activate Don t power off the switch while it s working Default Reboot System Ports VLANS fe Qos Aggregation Discovery Factory Default Are you sure you want to perform a FACTORY DEFAULT This wil only restore the factory defaults No Warm Aestart will be performed Perform manually if desired 328Reboot 2 To reboot the switch 1 Click the Reboot button on the Home page 2 Click Apply to activate Don t power off the switch while it s working Default Reboot System Ports VLANS QOS Aggregation Discovery Warm Restart PLEASE LOGIN AGAIN AFTER YOU CLICK THE APPLY BUTTON Are you sure you want to perform a Warm Restart Apply 17 4 Product Specifications Standard IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE 802 3x full duplex operation and flow control IEEE802 1p Traffic prioritization Interface 24 10 100Mbps auto MDI MDI X RJ 45 Switching ports 1 RS 232 Console port R 45 1OBASE T Category 3 4 5 UTP STP R 45 LOOBASE TX Category 5 UTP STP LED indications System Power RJ 45 Port 10 100M Link Act 320K bytes Buffer Memory FCC Class A VCCI A Temperature Operating Humidi 10 90 Power Sup
9. on No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2004 All Rights Reserved Table of Content UNPACKING NOMANI annn 1 1 Introduction to 24 port Fast Ethernet Web Smart Switch ssis 2 1 1 General Description sccccssidsdnnvmendadentcedasemihassaidsdusuaehiavaaieduauaddonsasiauns 2 LAr ole CN e E E E E S 3 13 EF OME FGI el siigusiterinacteiien tiie ciateiion nics anai 3 LA The Red PANE annonce menansiananteindaastueaincinne 5 2 Installing 24 Fast Ethernet Web Smart Switch 6 2 1 Desktop Installation srcsosnesatuseins sssnnnsecetiineaareyeeapasadenatsesenpesdemmnenmnaren 6 2 2 Rack mount Installation sscnnetincmiviartiecinndenestiecniemaaniud nas 6 2 3 Installing Network CableS cscscsssssssesssssssrsesrssrsrssserstssterseess 1 2 4 Network Application sisssaczanniasdatesntannunthiaussanatosnenses Ganwoncenineiaasinameteanmets 3 Mo agement GUINE sasersarccsusarensducscenssessavatsassnersescnsuadsavansaccsttrendsanparsinssanstiens 8 LACCO TIE S WIC Miccaniptaucnasasieintesenevasutatustie sphitunmtaneinaecanetantseaustlense mas 8 SALHON PAO nea eeesenasiae 10 3 2 1 SYStEM uncenssieaunimsestunsrcaunanadeninnnaeanrcindsaartavsmipinsessetinamintan 11 Le FON E A A E A E 12 PLEAN aer E E 13 3 2 4 Aggregation Trunking Configuration esseere 14 PASAO 0 EE EOE E
10. ply Internal power 100 240V 50 60Hz
11. t base To Disable the QOS click Disable and Click apply to save To use the TOS select TOS and click Apply to save To enable the Tag Base select Tag base and click Apply to save When you enable Port Base packets from the port you select will have higher priority To enable the Port base 1 Select the port base 2 Select the port base ratio 1 4 1 8 1 16 Always High The higher a ratio is the higher priority the port will get 3 Select the ports in the table High means high Priority and Low means Low priority The priority depends on the Port Base rate 4 Click apply to save Baba F p te a ort priorty 4 4 Q Nn 3 2 6 Discovery When you install several 24port Fast Ethernet web smart switches the discovery management tool helps you to search and access those switches on the LAN easily Therefore you can access any switch on your LAN without memorizing those IP addresses You can only find switches with the IP Address compatible with the one you access Note The Maximum number of Address listis 16 Auto Search 1 Click the Auto search button to find the switches 2 The IP address amp name of Switch list will appear 3 Click the one you want to access Default Reboot System Ports VLANS QOS Aggregation Discovery Discovery Auto Search Manual Add IP Address Name show search ip No search ip system name show the manual add result NO marmal
12. t session Internet Browser over the network in band Factory Default value IP 192 16811 Subnet M k 255 255 250 DefaultGateway 192168124 3 1 Access the Switch Console Port Out of band connection The operating mode of the console port is DCE 9600 Fix baud rate n No parity checking 8 8 Data bits 1 1 stop bit None No flow control After attaching a RS 232 cable Straight through to the serial port of a PC running a terminal emulation program press Enter key then login screen appears Enter your username and password to login the management console Note The management functions of console program are exactly the same with web based management interface but in text mode Attention 1 The factory default value of UserName and Password is admin 2 System configurations via the Console Port only will be allowed by the way of master device In Band Connections Web Browser Telnet To manage the switch through in band access you should configure the management station with an IP address and subnet mask compatible with your Switch 1 Running your Web Browser and enter the IP address 192 168 1 1 as the URL in the address field 2 Key in the User name and password to pass the authentication The factory default value of User Name and Password Is admin Please type your user name and password 24FE Smart SW Site 192 165 1 1 MENE 3 After au
13. thentication procedure the home page shows up 3 2 Home Page On the Home page you can select the configuration by clicking the menu tabs located on the upside of the UI It includes System P orts VLANS Qos Aggregation Discovery To restore the default Values of switch Click the Default Button If you want to reboot the switch click the Reboot Button 10 32 1 System To set up the system configurations such as login value system name and IP address E Defauli at Reboot P Address Subre Mack Caleway Nanie Password Functions Lee LL Aa e ee e R e A LLIA LA TuT The Mac Address of the switch The Hardware version Name of the Switch Setup the IP of Switch System Configuration MAC Aafia es Pda Of ak SAW Viman Ti HAY version 10 Sysiem management Web Console Foyt Mrami MFE Sman SW Aay Items Mac Address S W Version H W Version _ System name IP Address Subnet Maski Gateway Name Password Setup the Subnetmask of Switch lt Setup the Gateway of Switch The Login name defaultadmin The Login password default admin To save the configuration of the system click apply to save 11 3 2 2 Ports On the page you can view the Port status set up the Speed mode and enable the FDX flow control Port Configuration Far Fibl Operni mode Pambo idih Flow cantonal Like State 5 sant Aip
14. tons Add Add the entry into the VLAN Table Remove Remove the Entry you select Modify Modify the Entry you select Apply Apply the Mode you select Provides web manage security function click enable VLAN group web manage to support web manage function for VLAN group Default Reboot VIAN 1 1 43 4 5 6 7 0 9 10 11 1413 14 15 16 1718 19 20 21 22 23 24 Enable management VLAN 2 12 3 45 678 9 1014 15161718 192001 oo VLAN MODE ODISABLE PORT BASE Select member 0l laze Moa 104 105 106 MOF Moe Moo KILO v1 M12 13 W114 115 M 16 M17 118 M19 M20 M21 M22 W123 M24 M Note 1 The VLAN value can t exceed 24 2 Port 13 will take over management once you enable VLAN 13 3 2 4 Aggregation Trunking Configuration _ To set up the Port trunk groups select Enable of the group you need Don t forget to click the Apply to save the setting Supports 6 trunk groups for network application Agaregation Trunking Configuration TRUNK GROUP 1 Portt2 Portl4 Enable Disable TRUNK GROUP 2 Port03 Pornt04 Porti6 Potis C Enable Disable TRUNK GROUP 3 Porn06 Pornt0s Poti Potls Enable Disable TRUNK GROUP 4 Porn0 T Fornt0s Portl Port20 2 Enable O Diable TRUNK GROUP 6 Port06 Portl0 Porte1 Port22 C Enable Disable TRUNK GROUP 6 Portl1 Portl2 Port23 Port24 Enable O Disable Apply 14 3 2 5 Qos There are three modes of Quality of Service to choose TOS Tag Base and Por
Download Pdf Manuals
Related Search