AB-716-QH OIPM-2011.qxd_Page 1
Contents
1. Do not unplug the heater The fan will continue to operate even after the power switch is turned off The heater is in cool down mode Once the fan has stopped it is safe to disconnect the power cord Check your electrostatic filter to make sure it is free from dust and dirt and clean if necessary Be sure the front grille and rear vent intake are not being blocked Infrared Quartz Room Furnace NEVER LEAVE HEATER UNATTENDED WHILE OPERATING Infrared Quartz Room Furnace 1 YEAR LIMITED WARRANTY Pinnacle Products International Inc warrants this product to the original retail purchaser only to be free from defects in material and workmanship for a period of one 1 year from the date of initial purchase This product must be properly installed maintained and operated in accordance with the instructions provided Pinnacle Products International Inc requires reasonable proof of your date of purchase from an authorized retailer or distributor Therefore you should keep your sales slip invoice or cancelled check from the original purchase This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service within the warranty eriod and which Pinnacle Products International Inc shall determine at its reasonable discretion This warranty does not apply to products purchased for rental use This Limited Warranty does not cover any failures or operati2. Inspect heater closely for any damage that may have occurred during shipping If there is any damage return the heater to the place of purchase Remove heater from carton by sliding it out of the box and inspect for damages Save carton and packing materials for later off season storage Remove all protective packaging protecting heater during shipping Infrared Quartz Room Furnace NEVER LEAVE HEATER UNATTENDED WHILE Infrared Quartz OPERATING Room Furnace Operating Instructions 3 Holding down each button for 2 seconds while setting the time will change the time quicker If no button is pressed within 5 seconds the time status will switch NOTE UP and DOWN arrow buttons on the control back to the temperature status panel and remote control have dual function capabilities Use the UP arrow to adjust TIME TEMP or HI LOW settings To set Temperature Use the DOWN arrow to adjust TIME TEMP or C F 1 Pressing the TEMP button the LED display will switch settings to the TEMP status and begin to flash You must press the HI LOW UP button or the C F DOWN within 5 1 Plug the power cord directly into a conventional 120V 15 seconds to set the temperature amp grounded outlet and press the MASTER POWER 2 Pressing the the HI LOW UP button will increase the switch on the back of the heater temperature setting by 1 Pressing the C F DOWN 2 Press the POWER button on the fron
3. cool down mode before unplugging heater Do not operate this heater near any water Keep heater area free from combustible materials such as gasoline paint thinners and other flammable vapors and liquids Dust is combustible Do not use heater in areas of high dust concentration NEVER leave heater unattended ALWAYS maintain proper distance from combustibles Page 2 Aero Bella Do not open this heater unless instructed by an author ized representative of the manufacturer There are lim ited user serviceable parts inside Minimum clearance from Combustibles TOP SIDES FRONT BACK 24 12 12 36 Product Features 4 Infrared quartz bulbs Each infrared quartz bulb is rated at 375W and warms the air as is passes through the inner chamber Cross flow fan The cross flow fan creates a wide flow of air using a cylindrical shaped impeller Delay start function This function controls the cross flow fan and allows the infrared quartz bulbs to heat up before the fan begins to circulate the air flow The cross flow fan will also continue to operate after the heater is turned off to circulate the warm air out of the heater cooling the unit down Copper Plate The Diathermanous copper plate is constructed from red copper to enhance and improve efficiency LED Display This displays the temperature and time Operating the heater can be done on the unit s control panel or by remote Unpacking and Assembl
4. ER CHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION FURTHER Pinnacle Products International Inc SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL OR CONSEQUENTIAL DAMAGES Pinnacle Products International Inc assumes no responsibility for any defects caused by third parties This Limited Warranty gives the purchaser specific legal rights a purchaser may have other rights depending upon where he or she lives Some states do not allow the exclusion or limitation of special incidental or consequential damages or limitations on how long a warranty lasts so the above exclusion and limitations may not apply to you Pinnacle Products International Inc does not authorize any person or company to assume for it any other obligation or liability in connection with the sale installation use removal return or replacement of its equipment and no such representations are binding on Pinnacle Products International Inc Always be sure to specify model number and serial number when making any claim with Pinnacle Products International Inc For your convenience use the space provided below to list this information Model AB 716 QH Serial Date of Purchase Page 5 Infrared Quartz Room Furnace
5. and through filter to remove dirt and dust If desired you can use a mild soap to help remove dirt and dust Shake water from filter and replace in heater a damp filter can be replaced into the heater NOTE Repair of this heater should be done by a quali fied service person It is recommended that you save all of the packaging materials that came with your heater and re package the heater using these materials for safe storage Debris dust and dirt inside of the heater body can affect the performance of your heater This debris can impair the heaters ability to draw air for ventilation a pireee Parts List umber Part Description Part Number e I Bpea0o The Manufacturer reserves the right to make any changes in materials specifications prices or design without notice The Manufacturer may also discontinue items at any time Troubleshooting Guide Possible Cause Solution SSS Heater does not turn on No power from outlet Not pluged in MASTER POWER switch is off TIME is flashing on LED Heater continues to operate 1 after power switch is turned off The amount of heated air leaving the front of the heater is reduced Filter is dirty Vents are blocked Page 4 Aero Bella Heater is in cool down mode Be sure outlet is in working order Be sure heater is plugged in Press MASTER POWER switch Press POWER button to turn off TIME and resume normal operation of the heater
6. eS aes a i ty orai User s Manual and Infrared Quartz P I N N A CLE Operating Instructions Room Furnace S N Qero bea Model AB 716 QH Table of Contents Intertek Safety MPORMAMU ON isso ddecicdnc heads cvessationebdeccoemmnesncinemunedeneccsanrs 2 nterte Product Te MS cence ss sae eaeetggatestateics eee ieee 2 Unpacking and ASSEMDI cccccccseeeeseeeeeeeeeeeeeeaeeeesaees 2 Operating Instructions jets E A E T A a 3 IMPORTANT Read and understand all of the Storage Maintenance ccccccccceeceeceseeseeceeeeeeeeeeeaeeneees 4 directions in this manual before starting the heater Troubleshooting nesnenin i 4 lmproper use of this heater can cause serious injury AERE S AAEE E E E EE EAN sade E E 5 Keep this manual for future reference Heater is intended for residential use Do not use outdoors CONSUMER Retain this manual for future reference Pinnacle Products International Inc 668 Stony Hill Road 302 Yardley PA 19067 USA Phone 215 891 8460 Fax 215 891 8461 Web www pinnacleint com Email info pinnacleint com 841000100 11 NEVER LEAVE HEATER UNATTENDED WHILE OPERATING Infrared Quartz Room Furnace Safety Information If the information in this manual is AWARNING Not followed exactly a fire electric shock or explosion may result causing property dam age personal injury or loss of life he not operate this heater until you AWARNING have read and thoroughly under sta
7. eter within 4 degrees C F DOWN within 5 seconds to set the time Each 3 Once the desired temperature is set press TEMP button time you press the HI LOW UP button the time will to save your settings increase by 0 5 hours Pressing C F DOWN will decrease by 0 5 hours The maximum amount of time is NOTE To reset back to factory settings press and hold the 8 hours once you reach 8 0 the time will return to TIME button for 5 seconds and start at 0 5 again To turn heater off 1 Press POWER button on control panel or remote control Fan will continue to run in cool down mode 2 When fan has shut down you can unplug heater Do NOT turn off MASTER POWER A CAUTION switch or unplug heater until the fan has shut down If prematurely turned off the heater H ec Le e F can overheat which may damage your heater and void your warranty OOSORODES POWER TIME TEMP HI LOW CF Figure 1 LED Display Aero Bella Infrared Quartz Room Furnace Page 3 i NEVER LEAVE HEATER UNATTENDED WHILE OPERATING a Infrared Quartz Room Furnace Maintenance Storage NOTE Before care or maintenance is applied be sure heater is not plugged in The cabinet housing can be wiped down with a damp cloth or with furniture polish Your heater comes with a washable filter The filter should be cleaned regularly for maximum performance Remove the filter from the heater and run warm water over
8. nd these safety and operating instructions Only persons who can read and understand these instructions should use or service this heater Do not block the intake openings or heated air flow in any manner Check the heater thoroughly for damage before each use DO NOT operate a damaged heater Do not operate heater if the cord or plug is damaged DO NOT modify this heater or operate a heater that has been modified from it s original state Modifying this heater will void your warranty and could result in injury and or death Do not run heater cord below carpeting throw rugs run ners or similar coverings Do not run heater cord below furniture or any appliance Be sure heater cord is out of traffic areas Do not use this heater in bathrooms laundry rooms or similar indoor locations where humidity is high Never operate heater in or near a bathtub shower or swimming pool Keep children and animals away from heater Always set heater on a stable level surface Do not plug this heater into any other cord connect ed device such as a power strip surge protector multiple outlet adapter grounding adpater outlet type air fresheners or extension cords Plug the heater cord directly into a 3 prong 120V 15 amp grounded circuit receptacle Never plug heater cord into a loose fitting or broken receptacle Never use this heater below a receptacle Be sure heater is turned off and fan has completed its
9. ng difficulties due to normal wear and tear accident abuse misuse alteration misapplication improper installation or improper maintenance and service by you or any third party Failure to perform normal and routine maintenance on the heater shipping damage damage related to insects birds or animals of any kind and damage due to weather conditions are also not covered In addition the Limited Warranty does not cover damage to the finish such as scratches dents discoloration rust or other weather damage after purchase All transportation costs for the return of the damaged product or parts will be the responsibility of the purchaser Upon receipt of damaged item Pinnacle Products International Inc will examine the item and determine if defective Pinnacle Products International Inc will repair or replace and return the item freight pre paid If Pinnacle Products International Inc finds the item to be in normal operating condition or not defective the item will be returned freight collect Aero Bella This Limited Warranty is in lieu of all other express warranties Pinnacle Products International Inc disclaims all warranties for products that are purchased from sellers other than author ized retailers or distributors AFTER THE PERIOD OF THE ONE 1 YEAR LIMITED WAR RANTY EXPIRES Pinnacle Products International Inc DIS CLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF M
10. t control panel or ened WU Geigase We pear pete i ine on the remote control to start the heater The LED will maximum temperatuse setting is 86 F display the default setting 72 F 22 C 3 Holding down either button while setting the temperature will increase or decrease the temperature NOTE If the current ambient temperature is greater than the l ike z quicker If no button is pressed within 5 seconds the set temperature the HI LOW display fan and Quartz bulbs will not operate time status will switch back to the temperature status To set Heat Output To altern ween F and C Jee Se ee eee you can switch the 1 The default setting is HI Press the HI LOW UP button temperature format from Fahrenheit to Celsius and vice to switch from HI 1500W to LOW 750W versa To calibrate Temperature setting To set Timer 1 Hold down the TEMP button for 5 seconds to switch to 1 Pressing the TIME button the LED display will switch thermostat calibration status The LED display will from the temperature status to the TIME status and begin to flash The default setting on the display is 00 begin to flash The default time will display which 2 Press the the HI LOW UP or C F DOWN buttons to means the TIME is not activated and the heater will scroll up or down for the correct calibration The remain on displayed temperature should match your wall or 2 You must press the HI LOW UP button or the free standing thermom
Download Pdf Manuals
Related Search