FA422 Installation Instructions
Contents
1. FA100 FA422 Installation Manual Page 7 of 11 02793 FM Programming ALTARMING Transmitter 1 Plug the free end of the programming cable into the programming header on a Security transmitters Refer to the trans mitter s user manual to access its programming header When programming is completed this transmitter will arm the system when its alarm signal is transmitted and disarm the system when its restoral signal is transmitted 2 Follow the Adding RF Points instructions in the D2000 Series Keypad Diagnostics manual to program an identification code ID into the transmitter and to program the transmitter with any desired custom options Stop when the keypad dis play shows the following ACTIVATE POINT nn where nn is the transmitter point number to be programmed 3 Press the TRANSMITTER TYPE pushbutton two times The flashing LED above this pushbutton should move from SECURITY to COMMAND and then to ALT ARMING 4 If custom programming options are desired set the DIP switches located above the CUSTOM OPTIONS pushbutton switch to the desired transmitter options See Figur e5 on page 4 The meaning of the switch settings is as follows Table 4 Custom Option DIP switch settings Switch 1 Switch 2 Switch 3 N C N O STD W STD EOL Normally Closed Normally Open No Internal Contacts Internal No EOL EOL Contacts Resistor Resistor 5 If custom programming options are desired indicate this desire to the Expander b2. and put the Expander s cover back on FIGURE 5 Expander Programming Detail Omg ALT ARMING N C flog N0 0m command sTDR SELECTED so Wo 0 Security LED Qm security id SELECTED F TRANSMITTER CUSTOM EXT D SPVN TAMPER TYPE OPTIONS WINDOW Programming header FA422 Installation Manual Page 4 of 11 02793 FM Programming SECURITY Transmitters Using Factory Defaults In most cases Security transmitters should be programmed without changing the factory default settings like Normally Open contacts An exception to the rule might be the programming of universal door window transmitters To see if factory default settings for these devices match the application requirements referto Table 2 Table 2 Factory Default Settings for Selected Security Transmitters Transmitter Model Transmitter External Contacts Internal Contacts Expects Number Description Condition Activated EOL Resistor FA200 Universal Door Window Normally Closed No No FA200W Universal Wide Gap Normally Open Yes No FA210 Reduced Size Normally Closed No No Universal FA210W Reduced Size Normally Open Yes No Universal Wide Gap FA210M Reduced Size Universal Normally Open No No for Momentary Switch FA210DBN Reduced Size Universal Normally Closed No No with Switch De Bounce FA250 High Power Universal Normally Open No No To program a Security transmitter without changing its factory default sett
3. signal from an Inovonics transmit ter that was programmed into the system When a transmitter sends an alarm or check in signal VALID should start flashing VALID Status Always Off Flashing Always On Probable Causes No power to Expande Normal Transmitter programming problem of Problem Broken or unprogrammed transmit when a transmitter is activated Broken Expander ter s or checkin gin Broken Expander Troubleshooting with the Cover Off All three diagnostic LEDs visible with the cover on are also visible with the cover off Therefore all troubleshooting tech niques discussed in the previous section also apply to this section Additional diagnostic LEDs are visible with the Expander cover off These are the LEDs used for transmitter programming They can be used to troubleshoot problems with individual transmitters by allowing the installer to check how it was pro grammed To check how a transmitter was programmed do the following 1 Locate the transmitter s reset pushbutton Refer to the transmitter s user manual 2 Press the transmitter s reset pushbutton one time and note which programming LEDs light The lighted LEDs will stay on for a few seconds If the wrong LEDs light up the transmitter had been misprogrammed Note that if the SELECTED LED located beneath the DIP switches is on this only indicates that the transmitter was pro grammed with one or more custom options The current positions of
4. 1 Security Transmitters Compatible with the FA422 Transmitter Transmitter Transmitter Description Model Number Description FA200 Universal Door Window FA206I S Inovonics and Sentrol PIRs FA200W Universal Wide Gap FA206DS Detection Systems PIR FA210 Reduced size Universal FA207 Glassbreak Detector FA210W Reduced size Universal Wide Gap FA209 Billtrap FA210M Reduced size Universal for Momentary Switch FA216L H Low and High Temperature Detectors FA210DBN Reduced size Universal with Switch De bounce FAS25 Repeater FA250 High Power Universal FA536 Locator FA201 Smoke detectors FA202 FA570 High Power Indoor Repeater FA203S D Pendants FA205S D FA204 FA223S Security Repeaters Command Transmitters system arming disarming and special functions FAS75 High Power Outdoor Repeater Security transmitters can also be made to arm and disarm a system See Alt Arming information page8 All FA Series Security repeaters FA113 Three function Command transmitter FA100 Four function Command transmitter Note The FA130 Wireless Keypad is NOT compatible with Radionics 2000 Series Control Panels A CAUTION If an FA100 is used with the Expander the C key on the Radionics keypad s must not be programmed for an emergency function Pressing the key on the FA100 one time has the same effect on a 2000 series panel system as pressing the C key ona Radionics keypad two times If the C
5. D Arming Transmitters Plug the free end of the programming cable into the programming header on one of the Command transmitters Refer to the transmitter s user manual to access its programming header The two compatible transmitters are shown in Fig u re6 Follow the Adding RF Points instructions in the D2000 Series Keypad Diagnostics manual to program an identification code ID into the transmitter while leaving the transmitter s factory default options unchanged Stop when the keypad ACTIVATE POINT nn where nn is the transmitter point number to be programmed display shows the following Press the TRANSMITTER TYPE pushbutton one time The flashing LED above this pushbutton should move from SECU RITY to COMMAND Continue to follow the Keypad Diagnostics manual s instructions except that instead of pressing the transmitter tamper switch press the transmitter s reset pushbutton switch to activate the programming Be sure the programming cable is still connected Note that the COMMAND LED changes from flashing to solid See Figu re5 This shows that the pro gramming was completed Note that Command transmitters are unsupervised and therefore no extended supervision window changes are permitted Remove the programming cable from the transmitter and put the transmitter s cover back on Follow the above procedure to program all other Command transmitters FIGURE 6 FA100and FA113 Command Transmitter FAII3
6. FA422 INOVONICS Frequency Agile 900MHz 16 Point Receiver Expander for Radionics 2000 Series Control Panels Installation Instructions 02793 Product Description The FA422 is a 900MHz receiver that functions as a wireless point expander This Expander can process information from as many as 16 Inovonics transmitters and communicate their individual point status to a specific class of Radionics control panels The FA422 can interface to all 2000 Series Control Panels that have wireless point expansion capability by way of Radionics proprietary MonoBus All Inovonics FA Series Security Transmitters and Repeaters are compatible with the FA422 This product has been designed for quick and easy indoor installation FIGURE 1 FA422 Housing Housing dly LED DECODE 900MHz 16 POINT EXPANDER van For Radionics 2000 SERIES CONTROL PANELS REPLY Q By INOVONICS Frequency Agile FA422 RECEIVE Housing Pry Slots FIGURE 2 FA422 Programming and Diagnostic Components Mono Bus Address Jumper Reply LED eF TeS Security LED Iso 9 00 L T s MADE CERTIFIED 4 COMPANY IN USA 02793 FM LIT FA422 Install 1999 InovonicsWireless Corporation Control Panels Security Transmitters Transmitter Model Number Compatibility All Radionics 2000 Series Control Panels with wireless point expansion capability includes D2212 D2212B and D2412U Most FA Series Security transmitters Table
7. SPVN WINDOW pushbutton one more time The SELECTED LED above this pushbutton should continue to flash but at a much slower rate than the SECURITY LED 5 Continue to follow the Keypad Diagnostics manual s instructions except that instead of pressing the transmitter s tamper switch press the transmitter s reset pushbutton switch to activate the programming Be sure the programming cable i still connected Note that the SECURITY LED and possibly the SELECTED LED above the EXT D SPVN WINDOW pushbutton changes from flashing to always on or solid See Fig ure5 This shows that the programming was com pleted If the LEDs do not change to solid the transmitter may not be compatible with this type of programming The transmitter version must be 1 80 or higher See label on box or label on transmitter printed circuit board If the transmitter version is lower than 1 80 the transmitter is compatible in every other way except that it must be programmed using Custom Options 6 Remove the programming cable from the transmitter and put the transmitter s cover back on 7 Follow the above procedure to program all other Security transmitters that can use factory default programming FA422 Installation Manual Page 5 of 11 02793 FM Programming SECURITY Transmitters Using Custom Options 1 Plug the free end of the programming cable into the programming header on one of the Security transmitters Refer to the transmitter s user manual to
8. access its programming header 2 Follow the Adding RF Points instructions in the D2000 Series Keypad Diagnostics manual to program an identification code ID into the transmitter and to program the transmitter with the desired custom options Stop when the keypad dis ACTIVATE POINT nn where nn is the transmitter point number to be programmed play shows the following 3 Note that the SECURITY LED is flashing to show that a Security device is about to be programmed 4 Setthe DIP switches located above the CUSTOM OPTIONS pushbutton switch to the desired transmitter options See Figur e5 on page4 The meaning of the switch settings is as follows Table 3 Custom Option Dip switch settings Switch 1 Switch 2 Switch 3 N C N O STD W STD EOL Normally Closed Normally Open No Internal Contacts Internal No EOL EOL Contacts Resistor Resistor 5 Indicate to the Expander that these options are desired by pressing theCUSTOM OPTIONS pushbutton switch one time The SELECTED LED beneath the DIP switches should start flashing Note that whenever CUSTOM OPTIONS is selected for a transmitter its check in time will be set to 60 seconds 6 Decide if the supervision window or supervision interval for the transmitter should be extended from the setting chosen when programming the control panel either 4 or 12 hours The options are to extend to 96 hours or to infinite hours Extending to infinite hours simply means that the r
9. ak performance avoid mounting the Expander on a metal surface or near large metal objects 4 Run the cable wiring from the panel to the Expander Avoid running the wiring next to electrical telephone or other data wiring Refer to the panel installation instructions to determine maximum cable length and other wiring details 5 Route the cable wiring into either the side or back of the Expander If the wiring is routed through the back of the Expander use a small side cutter or utility knife to remove the wiring knockout If the wiring is routed through the side lift out the wiring shutter See Figure7 6 IfDC power is supplied by the panel connect the cable wires from the panel to the Expander as follows Radionics Panel FA422 Expander Data O DATA Aux AUX Aux O AUX 7 There may be some installations where DC power to the Expander must be supplied by an external DC power supply Refer to the panel installation instructions for further details If DC power is supplied from an external DC power supply connect the cable wires from the panel to the Expander as follows Radionics Panel Data O A Aux OM FA422 Expander CAUTION Make sure power supply Power Supply O DATA negative terminal is isolated O AUX from earth ground gt _o14 O AUX 8 Mount the expander to a wall or surface using the supplied hardware See F igure7 FIGURE 7 FA422 Hous
10. control panel installation instructions 3 Remove the Expander s cover Use a small flat bladed screwdriver to gently pry housing cover open at pry point slots indicated See Figu rel 4 Using another short piece of multi conductor cable temporarily connect the Expander to the control panel by connecting DATA AUX and AUX terminals See Figu re3 FIGURE 3 Expander Control Panel and Keypad Connections FA422 Expander 5 Set up the Expander to respond to MonoBus address See Figure 4 or 8 by moving its address jumper FIGURE 4 Address Selection Header ADDRESS ADDRESS 7 8 7 8 DAAN Address 7 Address 8 6 Apply power to the control panel 7 Follow the Radionics control panel operating instructions and installation instructions to set up communication between the keypad control panel and Expander Note that when setting the Supervision Interval in the RF Parameters Group of the panel s program entry guide a 1 indicates a 4 hour interval not a 24 hour interval A 0 selection however still means a 12 hour interval Make sure the Expander address set up at the control panel matches the Expander address jumper selection If everything is working properly the REPLY LED on the Expander should be flashing See Fi gure2 8 Follow the control panel operating instructions to assign point codes to each transmitter Assign point codes to Command transmitters using the same proce
11. cs does not authorize any person to act on its behalf to modify vary or extend this warranty This warranty will apply to Inovonics Products only All other products accessories or attachments used in conjunction with Inovonics equipment including batteries will be covered solely by their own warranty if any Inovonics will not be liable for any direct incidental or consequential damage or loss whatsoever caused by the malfunction of Product due to products accessories or attachments of other manufacturers including batteries used in conjunction with Inovonics Products This warranty does not warrant the replacement of batteries that are used to power Inovonics Prod ucts The User recognizes that a properly installed and maintained security system may only reduce the risk of events such as burglary robbery personal injury and fire It does not insure or guarantee that there will be no death personal damage and or damage to property as a result Inovonics does not claim that the Product may not be compromised and or circumvented or that the Product will prevent any death personal and or bodily injury and or damage to property resulting from burglary robbery fire or otherwise or that the Product will in all cases provide adequate warn ing or protection Inovonics 3shall have no liability for any death injury or damage however incurred based ona claim that Inovonics Products failed to function However if Inovonics is held liable dir
12. dure described for RF keypads FA422 Installation Manual Page 3 of 11 02793 FM Transmitter Programming The Expander can program three different types of Inovonics transmitters e SECURITY transmitters are devices like universal transmitters door window sensors pendants wireless smoke detectors and wireless PIRs that send alarm restoral and check in signals e COMMAND transmitters are devices that arm and disarm a system and send programmable command signals such as Call the police or Open the garage door to the control panel e ALT ARMING Alternative Arming transmitters are Security transmitters that are given the capability to arm and disarm a system like a Command transmitter When a Security transmitter is programmed as ALT ARMING its alarm signal is interpreted by the Expander and sent to the panel as a system arming signal and its restoral signal is interpreted and sent as a system disarming signal Unlike Command transmitters Alt Arming transmitters can be assigned point codes that monitor their check in signals tamper condition and battery condition To set up the Expander for programming transmitters locate the programming cable supplied with the Expander and plug one end into the Expander s programming header See F igure5 When all transmitters have been programmed remove the cable from the Expander programming header store the cable in the open area to the left of the Expander s printed circuit board
13. eceiver is programmed not to ever look for check ins from that trans mitter Extended time options might be useful when supervising pendant transmitters that are out of the Expander s receiving range for days or weeks at a time To extend the supervision window to 96 hours press the EXT D SPVN WINDOW pushbutton one time The SELECTED LED above this pushbutton should begin to flash at the same rapid rate as theSECURITY and CUSTOM OPTIONS LEDs To extend the supervision window to infinite hours press the EXT D SPVN WINDOW pushbutton one more time The SELECTED LED above this pushbutton should continue to flash but at a much slower rate than the SECURITY and CUSTOM OPTIONS LEDs 7 Continue to follow the Keypad Diagnostics manual s instructions except that instead of pressing the transmitter tamper switch press the transmitter s reset pushbutton switch to activate the programming Be sure the programming cable i still connected Note that all of the flashing LEDs that have to do with supervision time or programming options change from flashing to solid See Figure 5 This shows that the programming was completed and the changes have been accepted by the Expander 8 Remove the programming cable from the transmitter and put the transmitter s cover back on 9 Follow the above procedure to program all other Security transmitters that need custom programming options FA422 Installation Manual Page 6 of 11 02793 FM Programming COMMAN
14. ectly or indirectly for any loss or damage arising under this limited warranty or otherwise regardless of cause or origin Inovonics maximum liability will not in any case exceed the purchase price of the Product which will be fixed as liquidated damages and not as a penalty and will be the complete and exclusive remedy against Inovonics Warning The User should follow all installation operation and maintenance instructions The User is strongly advised to conduct Product and systems tests at least once each week Changes in environmental conditions electric or electronic disruptions and tampering may cause the Product to not perform as expected Warning Inovonics warrants its Product to the User The User is responsible for exercising all due prudence and taking necessary precautions for the safety and protection of lives and property wher ever Inovonics Products are installed Inovonics strongly advises the User to program Products to be supervised whenever used in applications affecting life safety Users are warned that unsupervised devices are subject to undetected failure due to malfunction battery failure tampering or changes in environment FA422 Installation Manual Page 11 of 11 02793 FM
15. ing Base Wiring knockout a i Mounting holes 4 places Wiring shutter FA422 Installation Manual Page 9 of 11 02793 FM Troubleshooting The Expander contains a number of diagnostic LEDs that will aid in troubleshooting system problems Since some of these LEDs only are visible with the cover off this section will be divided into troubleshooting with cover on and troubleshooting with cover off Troubleshooting with the Cover On Three diagnostic LEDs are visible when the Expander cover is on DECODE VALID and REPLY The way they help to trou bleshoot a problem is as follows The REPLY LED shows the status of the communication between the Expander and the control panel This LED should flash once each time it responds to a data request from the panel During normal operation REPLY should be continually flashing REPLY Status Always Off Flashing Always On Probable Causes Broken cable connection Normal Broken Expander of Problem No power to Expander Panel communication problem Expander address not programmed at panel Broken Expander The DECODE LED flashes to show that the Expander is active and listening If it is not flashing check to make sure that power is supplied to the Expander The VALID LED shows the status of the successful number of signal decoding attempts of the 900 MHz radio receiver on the Expander This LED should flash each time the receiver successfully decodes an incoming
16. ings do the following 1 Plug the free end of the programming cable into the programming header on one of the Security transmitters Refer to the transmitter s user manual to access its programming header 2 Follow the Adding RF Points instructions in the D2000 Series Keypad Diagnostics manual to program an identification code ID into the transmitter while leaving the transmitter s factory default options unchanged Stop when the keypad display shows the following ACTIVATE POINT nn where nn is the transmitter point number to be programmed 3 Note that the SECURITY LED is flashing to show that a Security device is about to be programmed 4 Decide if the supervision window or supervision interval for the transmitter should be extended from the setting chosen when programming the control panel either 4 or 12 hours The options are to extend to 96 hours or to infinite hours Extending to infinite hours simply means that the receiver is programmed not to ever look for check ins from that trans mitter Extended time options might be useful when supervising pendant transmitters that are out of the Expander s receiving range for days or weeks at a time To extend the supervision window to 96 hours press the EXT D SPVN WINDOW pushbutton one time The SELECTED LED above this pushbutton should begin to flash at the same rapid rate as the SECURITY LED To extend the supervision window to infinite hours press the EXT D
17. key is programmed to perform an emergency function like calling the police accidentally pressing the key on theFA100 one time could activate the emergency function If it is desired to program the C key for an emergency function and have a Command transmitter activate this function use the FAI13 The two keys onthe FA113 must be pressed simultaneously to have the same effect as pressing the C key two times Housing dimensions Weight Power requirement Current draw Receiver type Operating Environment FA422 Installation Manual Specifications 6 38 x 3 60 x 1 10 5 3 02 10 2VDC 13 9VDC provided by external power supply or by panel via MonoBus 45mA typical 60 mA maximum frequency hopping spread spectru 32 122 F 0 50 C up to 95 relative humidity non condensing Page 2 of 11 02793 FM Expander Control Panel and Keypad Setup Before installing the Expander and wireless point transmitters it is recommended that the Expander control panel and a hard wired keypad be temporarily wired together Panel programming should then be performed and each transmitter assigned a point code It is easier to complete the necessary programming if all the equipment is in the same location The procedure is as follows 1 Make sure power has been removed from the control panel 2 Using a short piece of multi conductor cable temporarily connect a hard wired keypad to the control panel Refer to Radionics keypad and
18. the DIP switches will not necessarily indicate which options were selected FA422 Installation Manual Page 10 of 11 02793 FM gt P Warranty amp Disclaimer Inovonics Wireless Corporation Inovonics warrants its products Product or Products to con form to its own specifications and to be free of defects in materials and workmanship under normal use for a period of twenty four 24 months from the date of manufacture Within the warranty period Inovonics will repair or replace at its option all or any part of the warrantied product Inovonics will not be responsible for dismantling and or reinstallation charges To exercise the warranty the User User Installer or Consumer must be given a Return Material Authorization RMA Number by Inovonics Details of shipment will be arranged at that time This warranty does not apply in cases of improper installation misuse failure to follow installation and operating instructions alteration abuse accident or tampering and repair by anyone other than Inovonics This warranty is exclusive and expressly in lieu of all other warranties obligations or liabilities whether written oral express or implied including any warranty of merchantability or fitness for a particular purpose Inovonics will not be liable to anyone for any consequential or incidental damages for breach of this warranty or any other warranties This warranty will not be modified varied or extended Inovoni
19. the flashing LEDs that have to do with supervision time or programming options change from flashing to solid See Figure 5 This shows that the programming was completed and thechanges have been accepted by the Expander 8 Remove the programming cable from the transmitter and put the transmitter s cover back on 9 Follow the above procedure to program all other Alt Arming transmitters Testing After at least one transmitter is programmed the operation of the Expander can be tested as follows 1 Check to see that the REPLY LED is still flashing This shows that the Expander is communicating with the panel 2 Put one of the transmitters into its alarm or command condition This should cause the panel and keypad to give the cor rect alarm or command response It is recommended that all transmitters be tested before installation If a particular transmitter does not give the correct response troubleshoot the problem by following the Point Status instructions in the D2000 Series Keypad Diagnostic man ual and the Troubleshooting with the Cover Off instructions in this manual FA422 Installation Manual Page 8 of 11 02793 FM Installation 1 Remove power from the control panel Remove the temporary cables between the panel and the keypad and panel and the Expander 3 Determine an appropriate indoor location to mount the Expander The housing is designed for indoor use only Do not enclose the Expander in a metal box To assure pe
20. y pressing the CUSTOM OPTIONS pushbutton switch one time The SELECTED LED beneath the DIP switches should start flashing Note that whenever CUSTOM OPTIONS is selected for a transmitter its check in time will be set to 60 seconds 6 Decide if the supervision window or supervision interval for the transmitter should be extended from the setting chosen when programming the control panel either 4 or 12 hours The options are to extend to 96 hours or to infinite hours Extending to infinite hours simply means that the receiver is programmed not to ever look for check ins from that trans mitter Extended time options might be useful when supervising pendant transmitters that are out of the Expander s receiving range for days or weeks at a time To extend the supervision window to 96 hours press the EXT D SPVN WINDOW pushbutton one time The SELECTED LED above this pushbutton should begin to flash at the same rapid rate as the ALT ARMING LED To extend the supervi sion window to infinite hours press the EXT D SPVN WINDOW pushbutton one more time The SELECTED LED above this pushbutton should continue to flash but at a much slower rate than the ALT ARMING LED 7 Continue to follow the Keypad Diagnostics manual s instructions except that instead of pressing the transmitter tamper switch press the transmitter s reset pushbutton switch to activate the programming Be sure the programming cable is still connected Note that all of
Download Pdf Manuals
Related Search