Portable Hand Wash Unit
Contents
1. URCO Portable Hand Wash Unit Please read and keep these instructions These instructions cover the Burco portable hand wash unit model HW01 SKU 444448591 HWO01 76100 SKU 444448591 Glen Dimplex Professional Appliances Stoney Lane Prescot Merseyside L35 2XW Tel 0844 815 3755 www burco co uk INTRODUCTION To ensure you obtain full benefits from your new hand wash unit e Please read this instruction booklet carefully and follow all instructions e Ifyou are unsure of any aspect of the installation use or performance of your appliance please contact the after sales number shown on the back page SPECIFICATIONS HW01 0 litre 1 50 80 4 X4 INSTALLATION Installation Requirements It is essential that this appliance is installed correctly Installation should comply with all local electrical and health and safety requirements WEEE directive registration no WEE DKOO59TT At end of unit life dispose of appliance and any replacement parts in a safe manner via a licenced waste handler Units are designed to be dismantled easily and recycling of all material is encouraged whenever practicable Before Connection to Power Supply Remove all packaging Check the appliance for damage Report any damage immediately to the carrier or supplier Remove any protective plastic coating Any water in the unit is due to testing and is normal Check the available power supply corresponds to that shown2. Descaling In hard water areas scale will form on the element and interior This will adversely affect the operation of the hand wash if allowed to accumulate Descale on a regular basis using a proprietary descaler recommended for stainless steel kettles Follow the instructions provided with the descaling product and then refill with fresh water heat and discard the water before general use Trouble shooting No power to the Check supply socket is switched on appliance Check fuse and circuit breaker Check green power indicator is The appliance does illuminated not operate Empty Refill Thermostat or element Replace thermostat or element faulty WIRING DIAGRAM PORTABLE HAND WASH UNIT PCB PUMP INFRA RED R Breu lt gt BniBu i Bn ELEMENT THERMOSTAT qp Bu POWER INDICATOR GREEN OVERHEAT THERMOSTAT 50C a Bu Bk Wiring colour code Bk Black Bn Bu Gn Y Bn Brown Bu Blue Gn Y Green Yellow G Green R Red L N W White INLET SUPPLY CABLE This diagram is the property of Glen Dimplex Home Appliances Not to be reproduced or transmitted in any shape or form without the permission of Glen Dimplex Home Appliances 08 08 2011 SPARES LIST ALWAYS TURN OFF THE POWER SUPPLY AND REMOVE THE PLUG BEFORE REPLACING ANY PARTS 082610802 Elementkitinc sea i O 082626774 Neongreen _ _ V O 082626780 Wheelassembly _ _ O M Z GUARANTEE This hand wash un
3. 083188500 08 2011
4. which protects the unit from damage if allowed to boil dry or switched on without water If the cut out operates allow the unit to cool down carefully tilt the unit as there may be water in either the top or bottom sections then press the red reset button situated underneath the base Cleaning ALWAYS TURN OFF THE POWER SUPPLY AND REMOVE THE PLUG BEFORE CLEANING ALLOW THE HAND WASH TO COOL THIS HAND WASH IS NOT WATERPROOF DO NOT USE A WATER JET SPRAY TO CLEAN THE INTERIOR OR EXTERIOR OF THE APPLIANCE OR USE A WATER JET IN THE VICINITY OF THE APPLIANCE Lift out the bowl by the edges raising it the upper section and sliding it up the water spout When it is high enough rotate the bowl and spout until clear of the opening of the upper section Locate the quick release fitting this is the large white plastic fitting joining two pipes Ensure that the bezel is unscrewed to its fullest extent Grip the white fitting and firmly push the plastic ring at the top of the fitting into the body of the fitting This will release the lock and allow the upper pipe to be removed Then push the lower ring into the body of the fitting and remove the fitting from the lower pipe Release the catches and separate upper and lower sections Exterior Clean with water and detergent Do not use harsh abrasive cleaners as this could damage the surface finish Interior Brush any scale or sediment from the element and rinse thoroughly with clean water
5. bowl by the edges raising it off the upper section and sliding it up the water spout When it is high enough rotate the bowl and spout until clear of the opening of the upper section 2 Lift out the waste container remove the lid and check that it is empty IMPORTANT This container must be empty before use otherwise there is a chance of over filling 3 Replace the waste container in the top section and replace the bowl ensure that it is fitted snugly back in place 4 To fill release the catches situated either side of the handwash that secure the upper section to the lower 5 Lift the upper section until it is clear of the lower section noting two cutouts in the bottom edge These are to be positioned on the left hand side of the rolled edge of the lower container giving a resting position and allowing hands free access for filling 6 Pour clean water into the lower tank Never fill beyond the MAX fill mark 10 litre otherwise water will flow out of the overflow 7 Lift the upper section and replace it on the lower section aligning the two container seams Failure to correctly align these sections will result in difficulty in latching the two parts together and may damage the latches themselves 8 Relatch the catches ensuring the wire retainers are situated above the cleat on the upper section Be careful to avoid catching any part of yourself when the catches snap into place 9 Plug into the supply The indicator light will
6. d with the letter N or coloured black or blue The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red or brown Make sure that the connections are tight and that there are no loose strands of wire and no insulation trapped under the terminals Tighten the clamp in the plug making sure that it grips the outer covering of the cord If fitting a BS 1363 13A fused plug then fit a 13A fuse Tighten the plug cover securely If you are in any doubt consult a qualified electrician IMPORTANT if the supply cord is damaged it must be replaced by the manufacturer service agent or similar qualified person in order to avoid a hazard The supply cord may become warm when the appliance is in use WARNING THIS APPLIANCE MUST BE EARTHED A RESIDUAL CURRENT DEVICE RCD MUST BE USED WITH THIS UNIT Electrical connection 220 240V 50 60Hz 7 6 8 3A 1680 2000W Features Waste bucket and lid inside Water spout Sink bowl Latches holding top and bottom sections together Handles Water feed tube inside Wheels Overflow Infra red sensor housing Upper section Lower section Power indicator Reset button underneath USER GUIDE TURN OFF THE POWER SUPPLY AND REMOVE THE PLUG WHEN NOT IN USE BEFORE CLEANING AND BEFORE REPLACING ANY PARTS Filling IMPORTANT always put water in the unit before switching on 1 Lift out the
7. illuminate to indicate power to the unit and the water will start to heat up 10 Put your foot momentarily into the black plastic moulding at the bottom of the unit This interrupts an infra red beam which in turn operates the water pump Do this twice to prime the pump No water will be dispensed until this is done 11 The unit takes approximately 15 mins to reach full temperature 12 The unit is now ready to use Hand washing 1 To operate place your foot momentarily into the black plastic moulding at the bottom of the unit This interrupts an infra red beam which in turn pumps water out of the water spout for approximately 7 seconds Repeat by momentarily putting your foot back into the plastic moulding once the previous dispense has finished 2 When water is no longer dispensed from the nozzle when activated the lower tank may be empty IMPORTANT Turn off the power and remove the plug when empty 3 Empty the waste container and refill the lower tank as described above 4 If there is water remaining in the lower tank check that the quick release fitting is securely attached to both pipes see cleaning and descaling After use Disconnect from the mains supply and empty the waste container Water may be left in the lower tank when not in use for short periods but to maintain a supply of fresh water it should be emptied periodically and cleaned out Protective cut out The hand wash is fitted with a thermal cut out
8. it is guaranteed against defective materials or faulty workmanship for a period of 12 months on labour and 36 months on parts This guarantee is given subject to the appliance being used in accordance with the instructions supplied and on the supply voltage marked on the rating label The guarantee is subject to fair wear and tear conditions The guarantee does not cover consequential damage arising out of any failure acceptable under guarantee nor does it cover damage resulting from misuse accident or unauthorised alterations to the appliance Proof of purchase will be required In any communication with the supplier or manufacturer quote the model and serial number marked on the appliance rating label This guarantee does not affect your statutory rights The products are intended for commercial use as detailed in these instructions The Company has a policy of continuous improvement in product quality and design The Company therefore reserves the right to change the specification at any time IMPORTANT any service call resulting from a lack of regular descaling is not covered by this guarantee and will be chargeable Customer helpline For spares and after sales service please contact Burco on T 0844 815 3755 F 0844 815 3748 E info gdha com Glen Dimplex Professional Appliances A Division of Glen Dimplex Home Appliances Stoney Lane Prescot Merseyside L35 2XW www burco co uk GLEN DIMPLEX PROFESSIONAL APPLIANCES
9. on the appliance rating label Location This hand wash unit is for indoor use only Only use on a flat level surface that is adequate to support the weight when full of water Only use on a dry surface avoiding any possibility of water ingress into the lower electrical compartment Do not move the unit when the mains lead is plugged in Move using the side handles The appliance is only to be installed in locations where its use and maintenance is restricted to trained personnel The mains lead should reach from the mains socket without straining the connections or creating a trip hazard Keep the mains lead away from any hot surfaces Do not place the appliance near a hot gas or electric burner Electrical Connection Fitting a plug The mains lead of this appliance will already be fitted with a BS1363 13A plug If the fuse has to be replaced use a 13 amp fuse complying with BS 1362 If the plug is not suitable for your socket then the plug must be cut off and disposed of safely An appropriate plug should be fitted as follows IMPORTANT The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marke
Download Pdf Manuals
Related Search