Home

TAE 40A-80A ESC

image

Contents

1. 1 B Brake 1short tone 2 BB Battery Type 2short tone 3 BBB Cutoff Mode 3short tone 4 BBBB Cutoff Threshold 4short tone 5 Beep Start mode 1 long tone 6 Beep B Timing 1 long 1 short 7 Beep BB Governor Mode 1 long 2 short 8 Beep BBB Motor Type 1 long 3 short 9 Beep BBBB PWM Frequency 1 long 4 short 10 Beep Beep Built in BEC Output 2 long tones 11 Beep Beep B Motor Load 2 long 1 short 12 Beep Beep BB Lipo Cells 2 long 2short 13 Beep Beep Beep B Reset All To Default 3 long 1 short 14 Beep Beep Beep BB Exit 3 long 2 short Note Beep means a long Beep tone B mans a short Beep tone Usually 1 long Beep 5 short B Enter program mode RWNF Exit program mode Select programmable items Set item s value Programmable value 1 Enter program mode a Switch on transmitter move the throttle stick to the top position b Connect the battery pack to the ESC a special tone 123 emits that means the battery supply is ok c Wait for 2 seconds the motor will emit Beep Beep tone d Wait for another 5 seconds special tone means the like 56712 emits that program mode is entered 3 Set item value Programmable value You will hear several Beep tones in loop Set the value matching to a tone by moveing the throttle stick to top position when you hear the tone then a special tone 1515 emits that means the value is set and saved Keep t
2. Beep Beep Beep Beep 1 long 3 short 10S Beep Beep 2 long 12S Beep Beep Beep Beep 2 long 2 short While for normal voltage ESC supports 2 to 6 cells Lipo we still use 5 short Beep tones to represent 5S lipo and 6 short Beep tones to represent 6S lipo Begin To Use The New ESC Please check the wiring and connections carefully an1 Move the throttle stick to the bottom and then start the ESC in the following sequences 1 Move the throttle stick to the bottom position and then switch on the transmitter 2 Connect the battery pack to the ESC the ESC begins the self test process a special tone 123 is emitted which means the voltage of the battery pack is in normal range and then N Beep tones will be emitted mean the number of lipo battery cells Finally a long Beep tone will be emitted which means the self test is OK the aircraft or helicopter is ready to go flying e If nothing is happened please check the battery pack and all the connections e Ifa special tone 556712 is emitted after 2 Beep tones Beep Beep means the ESC has entered the program mode it is because the throttle channel of your transmitter is reversed please set it correctly e If the red LED flashes very quickly 2 times per second means the input voltage is too low or too high please check your battery s voltage 3 VERY IMPORTANT Because different transmitter has different throttle range you need to calibrate the throttle range and let the
3. ESC remember it Please read the instruction on the left bottom of this page Throttle Range Setting After correctly setting the throttle range the red LED lights when the throttle stick is moved to the top position Maximum throttle Alert Tone Input voltage is abnormal The ESC begins to check the voltage when the battery pack is connected if the voltage is not in acceptable range such an alert tone will be emitted Beep Beep Beep Beep Every Beep has a time interval of about 1seconds and at the same time the red LED also flashes 2 Throttle signal is lost When the ESC can t detect the normal throttle signal such an alert tone will be emitted Beep BeepBeep Every Beep has a time interval of about 2 seconds 3 Throttle stick is not in the bottom position When the throttle stick is not in the bottom lowest position a very rapid alert tone will be emitted Beep Beep Beep Every Beep Beep has a time interval of about 0 25 second The output power will be resumed as soon as the throttle signal is normal again Trouble Shooting Trouble Possible Reason After power on motor does not work no The connection between battery sound is emitted pack and ESC is not correct one Check the power connection Replace the connector with new After power on motor does not work such an alert tone is emitted and the red LED flashes at the same Input voltage is abnormal to
4. will make the ESC to be hotter 10 Built In BEC Output 5 25V 6V default is 5 25V 11 Motor Load Normal Heavy Very Heavy Auto For normal voltage ESC supports 2 6 cells Lipo the default value is Normal For high voltage ESC supports 5 12 cells Lipo the default value is Auto F3A Please note that Auto F3A option is only suitable for big motors of large scale airplanes such as F3A please don t use this option for big motors of helicopters When you accelerate the motor immediately if the motor suddenly stop running and emit scream sound please try to set this item to other value 12 Lipo Cells For normal voltage ESC supports 2 6 cells Lipo Auto 2S 3S 4S 5S 6S the default is Auto Note4 For high voltage ESC supports 5 to 12 cells Lipo Auto 5S 6S 8S 10S 12S the default isAuto Note5 2 This programmable item is available for lithium battery In the startup process the motor will emits several Beep tones to represent the lipo cells number it is helpful for you to check whether it is coincident with the actual battery pack or not Note5 Not4 If you choose Auto the ESC may mistakenly judge the battery cells when the voltage is less than 3 7V Cell so we strongly suggest setting the Lipo Cells manually Note5 For high voltage ESC supports 5to 12 cells lipo when the motor emits the Beep tone to represents the cells number a long Beep tone So 5S Beep 6S Beep Beep 1 long 1 short 8S
5. Check all the connections batte pack connection throttle signal cable motor connections etc Normal Startup Procedure Move the throttle stick to bottom position and then switch on your transmitter Connect the battery pack to the ESC a special tone 123 emits that means the battery supply is OK ISeveral Beep ton es emits to represent the number of lip battery cells As soon as the self test process is finished Beep tone will be emitted Move the throttle sti upwards to go flying now Throttle Range Setting Switch on the transmitter and then move the throttle stick to top postion Connect battery pack to the ESC a special tone 123 emits that means the battery supply is ok then wait for 2 seconds Beep Beep tone emits that means the highest point of throttle range has been correctly confimed the bottom battery cells Move throttle stick to position several Beep tones emits to representithrottle range the number of lipo Along Beep emits means lowest positic been confirm Program the ESC with the transmitter will be selected 2 Select programmable items After entering program mode you will hear 14 groups of Beep tones in a loop with the following sequence If you move the throttle stick to bottom position within3seconds after one kind of tones the corresponding item
6. Governor Mode Off Governor Low Governor High default is Off If the governor mode is activated the ESC will try its best to hold the motor speed at a fixed value Usually the throttle curve is a horizontal line you can change the preset motor speed by changing the height of this line The speed range of Governor Low is 100000RPM to 45000RPM for 2 poles brushless motor Governor High mode is 46000RPM to 200000RPM for 2 poles brushless motor In order to caneed to know the motor poles number and the gear rate of main drive gear vs the pinion For example if you are using a 6 poles motor that is 3 pair poles and the main drive gear is 150T the pinion is 13T so you can calculate as follow The rotation speed for the main rotor blades The speed of 2 poles motor 13 3 150 When you adjust the throttle curve please make sure that the motor can run at this preset speed even if the motor load is heaviest Please note that the governor mode function is automatically disabled if the throttle volume less than 60 8 Motor Type Normal Motor Special Motor 1 Special Motor 2 default is Normal Motor Usually the default value Normal Motor is suitable for most of motors but if the motor cannot run smoothly with this mode please try other 2 options 9 PWM Frequency 12KHz 24KHz default is 12KHz For some motors with high KV high speed and many poles the 24KHz PWM frequency may let them work more smoothly But the higher PWM frequency
7. User Manual of AE 45A 50A 65A 80A Electronic Speed Controller ESC Thanks for purchasing our Electronic Speed Controller ESC High power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the correct use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses or costs resulting from the use of the product Any claims arising from the operating failure or malfunctioning etc will be denied We assume no liability for personal injury property damage or consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation to compensation is limited to the invoice amount of the affected product Features e High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency e Maximum motor speed 210000 RPM 2 poles 70000 RPM 6 poles 35000 RPM 12 poles e 3 start modes Normal Soft Very Soft compatible with fixed wing aircraft and helicopter e Throttle range can be configured to be compatible with all transmitters currently available on market e Smooth linear quick and precise throttle response e Separate voltage regulator IC for microprocessor to get a better anti jamming capability e Multiple protection features Low voltage cut off protection over heat protection throttle signal
8. he throttle stick at the top position you will go back to Step 2 and you can select other items Or Move the stick to bottom position within 2 seconds will exit program mode directly 1 long 1 long 1 long 1 long Item 1 short 2 short 3short 4 short ishort 2short 3 short Beep Brake Off Soft Hard Very hard Battery Type Lipo NiMH Soft Hard Cutoff Mode Cut Cut Cutoff sh Threashold Low Middle High Customer Start mode Normal Soft Very soft Timing 0 3 75 7 52 115252 159 18 75 22 5 26 25 Governor Mode Off Governor Governor Low High Normal Special Special Motor Type Motor Motor 1 Motor 2 PWM Frequency 12KHz 24KHz output S250 ov Motor Load aoa Heavy ae Auto a Seay Normal Heavy o poe 510 125 Lpo Lipo Eelis Auto 2S 3S 4S 5S 6S be Ari fa a ee 2 ne p For normal ESC 5 to 12S Lipo The value with symbol is the factory preset value That is default value 4 Exit program mode There are 2 ways to exit the program mode a In step 3 after special tone 1515 please move the throttle stick to the bottom position within 2 seconds a In Step 2 after tones that is the item 14 move the throttle stick to the bottom position within 3second
9. loss protection e The output of the built in BEC is switchable within 5 25V or 6 0V e With governor mode for helicopter Wiring Diagram Battery Receiver lene Black Programmable Items 1 Brake Setting Off Soft Hard Very Hard default is Off 2 Battery Type Lithium Lipo or Li ion NiMH default is Lithium 3 Low Voltage Protection Mode CutOff Mode Soft Cut Gradually reduce the output power Hard Cut Immediately stop the output power Default is Soft Cut 4 Low Voltage Protection Threshold Cutoff Threshold Low Middle High Custom default is Middle 1 For lithium batteries the cutoff threshold of the whole battery pack is calculated according to the cells number For normal voltage ESC supports 2 6 cells Lipo the Low Middle High value for each cell is 2 85V 3 15V 3 30V For high voltage ESC supports 5 12 cells Lipo the Low Middle High value for each cell is 2 75V 3 0V 3 25V For example if the cutoff threshold is set to Middle then the threshold for a 3 cells Lipo battery pack is 3 15 3 9 45V 2 For NiMH and NiCd batteries the cutoff threshold of the whole battery pack is calculated as follows 2 Low 50 of the battery s battery s full charged voltage Middle 62 5 of the battery s full charged voltage High 75 of the battery s full charged voltage 2 If this programmable item is set to Custom that means you can set the cut
10. o high time Beep Beep Every Beep or too low Beep has a time interval of about 1 second Check the voltage of battery pa After power on motor does not work such an alert tone is emitted Beep Beep Every Beep has a time interval of about 2 second Throttle signal is irregular or lost Check the receiver and transmi Check the control cable of the E 3 After power on motor does not work such an alert tone is emitted Beep Beep Every Beep has a time interval of about 0 25 second The throttle stick is not in the bottom lowest position Move the throttle stick to bottor position Set the throttle transmitter to neural or even lower After power on motor does not work a Special tone 56712 is emitted after 2 Beep tones Beep Beep Direction of the throttle channel is reversed so the ESC has entered the program mode Set the direction of throttle channel correctly Please refer t the user manual of your transmitter The motor runs in the opposite direction e connection between ESC and the motor need to be changed Swap any two wire connections between ESC and motor The motor stop running while in working state Throttle signal is lost Check the receiver and transmi Check the control cable of throt channel ESC has entered low Voltage protection Land RC model as soon as possible and replace the batter pack Some connections are not reliable
11. off threshold for the whole battery pack very accurately with the step of 0 1V The program box or PC software through USB adapter is need to customize the value 5 Start Mode Normal Soft Very Soft default is Normal Normal is preferred for fixed wing aircraft Soft or Very Soft are preferred for helicopters The initial acceleration of the Soft and Very Soft modes are slower than Normal mode usually it takes 3 second for Soft mode or 8 seconds for Very Soft mode from 0 throttle advance to full throttle After start up if the throttle is closed throttle stick is moved to the bottom position and opened again throttle stick is moved upwards within 3 seconds the restart will be temporarily changed to Normal mode to get rid of the chances of a crash caused by slow throttle response This special design is usedful for aerobatic flight 6 Timing 0 3 75 7 5 11 25 15 18 75 22 5 26 25 default is 15 Note3 Usually low timing value is suitable for most motors But there are many differences among structures and parameters of different motors so please try and select the most suitable timing value according to the motor you are just using The correct timing valuemakes the motor run smoothly And generally higher timing value brings out higher output power and higher speed Note3 After changing the timing setting please test your RC model on ground prior to flight 7

Download Pdf Manuals

image

Related Search

Related Contents

user manual  Statistical Machine Translation System User Manual and Code Guide  Aufwickeleinheit Serie W SP 500/800  GBC HiGloss & HiClear  ProtoPlace S – Dispensing procedure Tutorial  PDF document  ft doser 4 _16-03-12  National Conference on Engineering Trends in Medical Science  

Copyright © All rights reserved.
Failed to retrieve file