Home

Manual

1. 12 VARYTEC 3 Introduction Thank you for buying the Air Base 600 with protective cover It is a powerful device For a successful installation and operation please read this manual carefully 3 1 Technical drawing 7 12 VARYTEC 4 Connections 4 1 Electrical connections If you wish to change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected Cable EU Cable US Pin International Brown Black Live Light blue White Neutral N Yellow Green Green Earth 4 2 DMX connections To make a DMX512 connection go ahead like it is described in the picture Make sure that you use shielded cable 3pole or 5pole XLR cables are suitable 4 3 DMX connection with terminator Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy environment like a disco for installations we recommend using a DMX terminator This prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR connector with a 120 O resistor between pins 2 and 3 which is then plugged into the XLR output Socket of the last device in the series Please look to the bottom drawings COMMON DMX 0201 n Not Used COMMON lt DMXINPUT DMX OUTPUT DMX 8 12 VARYTEC 5 Control 1 Light Source Switch On
2. 1 1 For safe and efficient operation Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 32 F 0 C or exceeding 104 F 40 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connec
3. EN60598 2 17 Installations are to carry out by skilled personnel only The suspension devices have to be build and measured so they can withstand for an hour the tenfold of the payload without suffering a permanent detrimental deformation Basically installation has to be made by using a second separate suspension This can be e g a suitable net The second suspension must be designed and attached so no part of the installation can fall down in case of failure During construction reconstruction and deconstruction unnecessary stay in the range of moving areas on lightning bridges under elevated work stations or any other danger zones is forbidden The operator is obliged to following safety related and mechanical facilities Before the first start up or after critical changes before restarting it has to be checked by an expert Review the frame of the inspection test at least all four years by an expert Review by a qualified person at least once a year How to carry out the overhead installation In tidal fall you should install the device out of the lounge area of people IMPORTANT Overhead installation requires a high level of experience This includes knowledge of calculating the payload used installation material and safety inspections of the used material and the projector whereas the required experience is not limited to this Do not try to carry out installation yourself under any circumstances if you are not qual
4. Off Switch for the device which is connected to 6 2 Mains In 3 Fan Setting the fan speed in 4 steps 4 DMX In Out DMX In Out 3pol 5pol 5 On Off On Off Switch for the device 6 Schutzko plug Connect a device 7 DMX In Out DMX in Out 3pol for the device which is connected to 6 For hanging this device you need an optional hanging kit 9 12 VARYTEC 6 Technical data Power supply Voltage AC 110 240 V 50 60 Hz Power consumption max 25 W Connections Strom in PowerCon XLR in out 3pol 5pol Hardware Protection class IP20 without protection cover Dimensions L B H 600 x 600 x 172 mm Weight 10 5 kg 10 12 11 12 VARYTEC Importeur B amp K Braun GmbH IndustriestraBe 2 D 76307 Karlsbad www bkbraun com info bkbraun com C 2002 95 12 12
5. es Operate the device not during thunderstorms Surge voltages could destroy the device Unplug the power supply during thunderstorms During the installation the use of the mounting bracket is obligatory Surrounding objects or surfaces should not be in contact with the device Make sure that during the installation and removal of the device the area below the place of installation is basically cordoned off This also applies to implementation of service The device has basically been protected by a suitable safety Make familiar yourself with the functions of the device before start up People without the experience should not handle with the device The most cause of functional disorder is inappropriate handling Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt For transport use the original packing or designated accessory to avoid damages during the transport For reasons of safety unauthorized changes are forbidden A usage of the device which differs from usages which are described in this manual can cause damages of the device In that case the warranty expires Additional you should notice that every differed usage is related with dangers and can cause e g an electrical short fire electric shock or crash 4 12 VARYTEC 2 1 Overhead installation Danger of life You have to observe the regulations of BGV C1 formerly VBG 70 and
6. ified Contact a professional installer An inappropriate installation can lead to injuries and or damaged properties It is not allowed to install the device in the grip area of people If the device may hang from the ceiling or from high beams the use of truss systems is mandatory The device may not be installed so it can swing freely in the room Please note Crashing down items can cause serious injuries Do not install the projector if you doubt the safety of a possible installation form Before installation make sure that the mounting surface has the ability to carry the tenfold point load of the own weight of the device Mount the device with the mounting bracket to your trussing system using an appropriate clamp During overhead installation the device must be always secured by a safety rope which is designed to hold the twelvefold weight of device Only safety ropes with quick release safety fastener elements may be used Hang up the safety rope in the hole of the mounting bracket Direct the rope over the truss or an appropriate fastening point Hang up the end in the fastening element and tie up the locking nut A safety rope once exposed to failing load or damaged may not be used furthermore 5 12 VARYTEC ipn The maximum drop exceed must not exceed 20cm A safety rope once exposed to failing load or damaged may not be used furthermore Adjust the desired inclination angle via the mounting bracket and tighten the screw 6
7. ignition 3 Fa 2 Air Base 400 with protective cover VARYTEC 1 2 3 4 5 6 Table of contents Saf ty INRSIYUCtiOnSu al 3 1 1 For safe and efficient operation uuu ARKAN RE 3 DESIQNALCCMUSG scsi ced atte 4 2 1 Overhead installat O M a 5 Te iol TETTE u TREE 7 Technical drawing iet erunt teda se a UD xe eee 7 CONMECTONS 8 4 1 Electrical CONMECHONS 8 4 2 DIMX COMNMEGCTIONS u reor ns re a DE Feu RENE aa RENTUR 8 4 3 DMX connection with terminator 8 9 EC MICAl musu aZ su n atas 10 2 12 VARYTEC 1 Safety instructions e This device is only suitable for outdoors combined with the protective cover e All modifications to the device will void the warranty e Repairs are to carry out by skilled personnel only e Use only fuses of the same type and original parts as spare parts e Protect the unit from rain and humidity to avoid fire and electric shocks e Make sure to unplug the power supply before opening the housing
8. tions have to be carried out according to the European safety standards 3 12 VARYTEC 2 Designated use This device was developed for professional use on stages in discos theatres etc The device is only approved for a connection up to 230V 50 60 Hz AC voltage and only for indoor use Combined with the protective cover it can also be used outside Regular breaks during operation increase the lifetime of your device Avoid convulsions or any form of forceful impact during the installation or the start up of the device Make sure that the device is not exposed excessive heat humidity or dust at the place of installation Take care that no cables are lying around You would endanger your own safety and also the safety of a third party It is only allowed combined with protective cover to operate the device in an environment in which spray water rain humidity or fog is expected Humidity or very high atmospheric humidity could reduce the isolation of the device and could cause deathly electric shocks If you use fog devices the device has not be exposed to a direct smoke jet There has to be a safety distance of at least 0 5m between this device and the fog machine Make sure that the saturation of the fog has to enable a visibility of at least 10m The ambient temperature has to be between 0 C and 40 C Avoid direct sunlight and close proximity to heaters You have also to attend it during the transport in closed motor vehicl

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents