Ferm Bench Grinder FSMC
Contents
1. extraction device Whenever there are facilities for fitting a dust or fume extraction system make sure itis connected and used Use recommended accessories The use ofany other accessory or attachment other than recommended in the instructions or catalogue may pre sentarisk of personal injury INSTALLATION Check package contents Check contents against list in this manual to make sure each item is present Check for damage Before using this item check each part listed is undama ged Save packaging Save major packaging for return of product for service or repair The grinder must be fixed to a suitable bench A Ensure the grinder is unplugged from the mains e Use 6mm diameter steel bolts nuts and washers to attach the machine the bolt length depends on the thickness of the bench The grinder is fitted with an earthed plug and must fit ted to an earthed socket Route the mains lead away from the machine and workarea e If the bench is made of steel it recommended that you place a wood or hard rubber panel under the machine before fixing to prevent vibration ASSEMBLING THE ACCESSORIES MOUNTING THE TRANSPARENT FACE GUARD EYE SHIELD A Do not use this machine without the eye shield in place and properly adjusted A Ensure the grinder is unplugged from mains Refer to illustration below Remove the Bolt A from the wheel guard push the mount with the eye shield attached onto the wheel guard replac2. person to determine that it will operate properly Check for alignment of moving parts binding or breakage of parts mounting and other conditions that may affect its operation A damaged part or guard should be properly repaired by an authorised service centre unless indicated otherwise in the instruction manual Have defective switches replaced by an authorised service centre Do not use a tool if the switch does not turn onand off Have your tool repaired by an expert This appliance is manufactured in accordance with rele vant safety standards Only experts must carry out repai ring of electrical appliances otherwise considerable dan ger for the user may result Storing tools When notin use tools should be stored in the dry out of reach of children Ferm ELECTRICAL INFORMATION This product is complete with a pre wired mains plug it s fitted with a 3 core mains cable and must be plugged in to an earthed mains socket only If the plug needs replacing follow these instructions Wire correctly The wires in the mains lead are coloured in the following way BLUE e Neutral BROWN e Live YELLOW GREEN Earth Securing wires Secure wires carefully and firmly to the correct termi nals Secure the mains cable in the plug cord grip firmly Fit a 5 amp fuse If a 3amp BS1363 plug is used a BS 1362 ASTA approved 5 amp fuse must be fitted Recycle Dispose of old plug and cable Prevent inadvertent connection to soc
3. right hand spindle Do not over tighten e Replace the guard eye shields and tool rest parts in the reverse order making sure that you adjust the tool restand eye shields e Tighten bolts nuts as appropriate Ferm TO MOUNT REPLACE THE LEFT HAND WET GRINDING WHEEL A Ensure the grinder is unplugged from mains Refer to illustration below e Check the grinding wheel is the correct type for the machine Only use wheels with the following informa tion marked on them Name of manufacturer Binding material Dimensions Maximum speed If this information is not clear or not marked on the wheel do not use it e Make sure maximum speed marked on the wheel is the same or less than that marked on the machine e Make sure the dimensions of the wheel are correct for the machine 200mm maximum diameter X 40mm width X 20mm arbour hole Donotalter wheels to fit the machine Mounting replacing the wheel Empty any water from the reservoir by removing the drain plug e Remove the three crosshead screws and washers from the water reservoir wheel guard and pull off downwards e Loosen the wheel retaining nut with a suitable 9mm spanner not supplied anticlockwise viewed from the back of he machine e Remove the nut flange washers and wheel from spindle e Clean the guard flange washers spindle and reser voir e Replace one flange washer the 20mm boss facing the grinding wheel then slide the new whee
4. ERATION A Make sure the switch on the grinder is OFF Plug into a suitable mains supply make sure the cable is routed well away from moving parts and switch on at plug Toswitch the grinder ON Push in rocker switch on the side marked Toswitch OFF Push in the rocker switch on the side marked O D URING USE Place the workpiece on the tool rest and push gently on to the revolving wheel do not use undue pres sure Donotuse the sides of the wheel for grinding Take care not let loose items rags small parts etc get caught in the wheels Regularly inspect the wheels during use for signs of damage or wear and dress or replace when required Make sure that a competent person carries this out If you are using water to cool the workpiece make sure it is in a separate stable container kept away from the machine and electrical plugs Fill the water reservoir on the left hand wet wheel with 300ml of water only Do not overfill Drain the water from the reservoir when notin use If you are using the wet wheel on a regular basis replace the water weekly When grinding edge tools take care not to overheat the edge this will draw the temper and make the tool blunt easily To stop this happening cool the tool fre quently with water Make sure the workpiece cannot get stuck between the wheel and guards tool rest Switch the machine off before removing the plug from the mains socket Wear appropriate personal protec
5. UK Subjectto change USER S MANUAL Document Ref FSMC 200 150 14544 PMR35 issue I May 02 Copyright These instructions are the sole property of Ferm Omega Tools and may not be reproduced Ferm Bench Grinder FSMC 200 150 erm Art nr 750357 Screwfix Art nr 14544 Ferm BV P O Box 134 8280 AC Genemuiden NL www ferm com 0211 05 CurYEngiish AY FERM BENCH GRINDER FSMC 200 150 USERS MANUAL TECHNICAL SPECIFICATIONS Voltage 230V Frequency 50Hz Power input 370 W No load speed 2950 min Grinding stone dimensions 150x20 12 7 mm Wetgrindingstonedimensions 200x40 20 mm Weight 12kg Lpa sound pressure 76 0 dB A PRODUCT INFORMATION On off switch Tool Rest Eye shield Eye shield mount Bolt for eye shield mount Wet grinding wheel Water reservoir ade ih teal tetas SAFETY INSTRUCTIONS The following pictograms are used in these instructions for use A Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual A Denotes risk of electric shock Carefully read this manual before using the machine Make sure that you know how the machine functions and how to operate it Maintain the machine in accordance with the instructions to make sure it functions properly Keep this manual and the enclosed documentation with the machine Ferm products are manufactured to high quality stan da
6. e the bolt nut and washer through the slots in the mount and holes in the wheel guard tigh ten finger tight e Adjust the mount 4 so there is a maximum gap of 5mm between it and the wheel as shown Tighten the mount bolt nut securely Adjust the eye shield 3 so that it gives maximum protection during operation e Make sure the eye shield bolt 5 is secure but does not prevent adjustment of the eye shield A Remember that you will always need to use safety glasses for protection as well as the eye guard when operating this machine MOUNTING ADJUSTING THE TOOL REST A Ensure the grinder is unplugged from the mains Refer to illustration below e Assemble the tool rest 2 with the short bolt facing inwards and the flat washer on the threaded side of bolt e Make sure the square under the head of the bolt loca tes in the slot on the wheel guard fit the tool rest washer and then screw on the thumbscrew finger tight e Adjust the tool rest so that the maximum gap between itand the wheelis 5mm e Tighten the thumbscrew firmly by hand 34 5 Ferm Ferm GUARANTEE The guarantee conditions can be found on the separately enclosed guarantee card CE DECLARATIONOFCONFORMITY UK We declare under our sole responsibility that this productis in conformity with the following standards or standardized documents IEC1029 2 4 EN61029 1 EN55014 EN55104 EN6 1000 3 2 EN61000 3 3 in accordance with
7. ket and risk of electric shock ENVIROMENT Recycle the packaging according to the identification marks on it At the end of the product or its accessories life please recycle where facilities exist Phone the Helpline for cur rentadvice on recycling Helpline For any queries relating to operational or safety matters contact Ferm Customer Helplineon 01159661199 Monday Friday 8am 6pm Saturday 9am I pm
8. l onto the boss spindle observing the correct direction if mar ked on the wheel and replace the second flange was her boss towards the wheel and the nut e Tighten nut clockwise viewed from the back of the machine Do not over tighten e Replace water reservoir by sliding upwards from underside of machine and reinstall the three crosshead screws and their washers Tighten with a suitable screwdriver e Replace the drain plug and refill the water reservoir with 300 ml of water if using the wheel Water reservoir mounting screws USING THE BENCH GRINDER BEFORE OPERATING Check the voltage on the bench grinder corresponds with your power supply voltage and that the plug and lead are in good condition e Check maximum speed marked on the grinding wheel is the same or less than the maximum speed of the machine The machine s speed must not be gre ater than the speed marked on the wheel You have the correct type of wheel for the machine and that it is mounted correctly Do not use parts other than supplied with the machine to make the wheel fit properly Ensure the eye shield and tool rest are adjusted pro perly Inspect the grinding wheels for any damage Do not use cracked or otherwise damaged discs e Setthe guard eyeand tool rest according the instruc tions Run idle for 30 seconds If there is any abnormal vib ration or other fault switch off inspect and rectify before continuing OP
9. l or pre scription non prescription drugs Ferm EXPLODED VIEW SPARE PARTS LIST FSMC 200 150 DESCRIPTION FERMNR SWITCH 206451 SUPPORT 206454 COVER GLASS 206401 COVER GLASS HOLDER 206132 WATER TANK 206442 GEAR 205450 Ferm II 10 Ferm OPERATIONAL SAFETY Warning Never use the machine for grinding magnesium workpieces Do not use this machine for grinding soft materials like aluminium lead or wood Do not use near flammable materials or people Concentrate Routine and repetition can lead to mistakes Remember that a slight lack of concentration can result in serious injuries ina split second Keep workarea clean Cluttered areas and benches invite injuries Consider the work environment Do not expose power tools to rain or use them in damp or wet locations Keep work area well lit Do not use power tools in the presence of flammable liquids vap ours or gases Guard against electric shock This unit contains dangerous voltages Use a RCD resi dual current device to provide protection against elec trical shock Prevent body contact with grounded sur faces e g pipes radiator ranges or refrigerators Keep children and pets away Do not let children or pets come into contact with the tool extension cable or work area Donot force the tool It will work better and safer at the rate for which it was intended Use the right tool Do not f
10. orce small tools or attachments to do the job ofa heavy duty tool Do not use tools for purposes for which they were not intended for example do not usea circular saw for cutting trees or logs Donotabuse the cable Never carry the tool by the cable or pull it to disconnect it from the power socket Keep the cable away from heat oil and sharp edges Do not touch the metal plug pins when connecting or removing the plug Do not over reach Keep a proper footing and balance at all times Disconnect tools from power supply When not in use before servicing and when changing accessories suchas blades bits and cutters A Always switch off and unplug the grinder from the power supply before making adjustments or chan ging grinding wheels Remove adjusting keys and wrenches Ensure that they are removed from the tool before swit chingon Ferm Avoid unintentional starting Check that the switch is off before plugging in to socket Extension cables Use only three core earthed extension cables suitable for the power input of the tool minimum cable size 1 5mm Plug into an earthed socket only When using a cable reel unwind it fully Do not use long extension cables If the tool is suitable to be used outdoors only use an extension cable intended for outdoor use and marked accordingly Use a RCD residual current device to provide protec tion against electrical shock Do not usein rain or damp conditions Connecta dust
11. rds they are safe and fit for purpose at time of sale but all tools can be dangerous if the correct precautions are not taken Always follow these instructions do not carry out the operation until you are sure you can do so in saf ety Remember to consider the work environment for safe operation as well as safety for tool use Warning When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury Read all these instructions before attempting to operate this product Save these instructions for future reference PERSONALSAFETY Use Personal Protection Safety Equipment Protect eyes with safety glasses or goggles note the use of safety protective eyewear without the CE mark can lead to serious injury if the lens breaks A suitable dust mask should be worn if cutting drilling or sanding is dusty in particular chipboard or MDF Approved safety footwear and headgear should worn as appropriate for example on building works or when heavy weights are involved Wear suitable gloves and apron to protect against sparks debris Wear earplugs or ear defenders Dress properly Do not wear loose clothing or jewellery It can get caught in moving parts Non skid footwear is recommended when working out doors Wear protective hair covering to contain longhair Stay alert Watch what you are doing Use common sense Do not operate tools when tired or after taking alcoho
12. the regulations 89 392 EEC 73 23 EEC 89 336 EEC from 01 07 1999 GENEMUIDEN NL ee W Kamphof get Aa Quality department Ferm TO MOUNT REPLACE THE RIGHT HAND GRINDING WHEEL A Ensure the grinder is unplugged from mains Refer to illustration below Check the grinding wheel is the correct type for the machine Only use wheels with the following informa tion marked onthem Name of manufacturer Binding material Dimensions Maximum speed If this information is not clear or not marked on the wheel do notuseit e Make sure maximum speed marked on the wheel is the same or less than that marked on the machine e Make sure the dimensions of the wheel are correct for the machine 150mm maximum diameter X 20mm width X 2 7mm arbour hole e Donotalter wheels to fit the machine Mounting replacing the wheel Remove the three bolts nuts and washers from the wheel guard and pull off the end plate and circular guard e Loosen the wheel retaining nut with a suitable 9mm spanner not supplied anticlockwise for the right hand wheel Remove the nut flange washers A and wheel from spindle e Clean the guard flange washers and spindle e Replace one flange washer the concave facing the grinding wheel then slide the new wheel onto the spindle observing the correct direction if marked on the wheel and replace the second flange washer concave towards the wheel and the nut Tighten nut clockwise for
13. tion equipment Do not wear loose clothes which could get caught in the wheel Keep hands away from wheel Ferm MAINTENCE CARE AND REPAIR A Switch off and unplug the machine before carrying out any cleaning or maintenance work CLEANING Clean witha soft brush or dry cloth Do not use water or flammable liquids to clean the grin der FAULTS Switch OFF immediately at the mains plug and remove the plug when The plug or cable is damaged The switch on the machine is defective You smell or see smoke caused by scorched insula tion in the machine e Thereis abnormal vibration from the wheels Overheating Putless pressure on the workpiece The machine does not start when switched on e Check the mains lead and the fuse plug e Taketo your Ferm Dealer for repair The motor is defective Taketo your Ferm Dealer Thereare no user serviceable repairable parts inside this machine Qualified service engineers must carry out repairs and servicing MAINTAIN TOOLS WITH CARE Keep the tool clean for better and safer performance Store the wheels properly in accordance with the maker s instructions Follow instructions for changing accessories Inspect tool and extension cables periodically and if damaged have them repaired by a qualified person or authorised service body Check for damaged parts Do not use a tool with damaged parts before further use a damaged tool must be carefully checked by a qualified
Download Pdf Manuals
Related Search