GSM Wireless Terminal With Fax Function WT
Contents
1. Table 4 1 Adjust Voice Volume Functions Parameter Command Specification Input parameter set password XXXX Success verify 4 digit password to enter management parameter set Table 4 2 Keypad Set COPYRIGHT 2006 WITURA CORPORATION SDN BHD 8 WT 209 GSM Wireless Terminal with Fax Function Functions Taram eter Semmand Specification Polarity reverse 20 20 Send polarity reverse signal for charge Set Send Cancel No Send default PINI 71 PINI 71 PIN1 PINI Max 8 digit no less then 4 digit Modify PIN1 72 old PINI New Before modify PIN PIN under active PIN1 New PIN1 status Set default parameter 81 Set default parameter Modify password XXXX XXXX Password is 4 digit New Password New Defaulted password is 1234 before Password factory Password cannot delete only can replace old password with new password Above only can operate after enter management parameter set Table 4 3 Modify Parameter After Enter Keypad Set 5 Care and Maintenance Operation of any radio transmitting equipment including cellular phones may interfere with the functionality of inadequately protected medical devices Keep the device dry Precipitation humidity and liquids contain minerals that will corrode electronic circuits Don t drop knock or shake the device TV set telephone set radio set PC and other electronic equipments may cause inte2. 3V SIM Cards Don t use any other types SIM Card Uy aly a a au ta Figure 3 1 SIM Card Installation Step 2 Connect the telephone set Connect the telephone set and device with the telephone line by inserting the connector into the Phone port on the device Step 3 Install the Antenna Step 4 Connect the power adapter Connect the power adapter to 220v AC power Be sure that the AC power has been grounded Connect the other side of power adapter to the DC Power socket in the device Step 5 Switch on the device The device may be ready for use after about 15 seconds later The registration time may vary according to the network environment in different area Press after finish dialed numbers can shorten dialing time WARNING Many types of telephone sets exist and they always have different electronic characteristics so it s recommended that the telephone set keeps at least 2 meters away from the equipment so as to protect the equipment and the phone set from interfering with each other Outer electromagnetic rays may interface with the equipment via radiation or conduction Some protection actions should be taken 1 Use only single phase 3 line alternating current power socket with the PE line installed well so that the filter circuit in the equipment works normally to filter the interference that come from the electricity network 2 Keep the equipment out of the radio transmitters and rad
3. drop off When call standby time dropped to half time need buy new battery 3 WT 209 only can recharge for equipped battery 4 Not use such battery for other application 5 Battery will self discharge if long time no use 6 Battery need keep under dry and warm environment keep in indoor condition Li battery will greatly effected when less than 0 C 7 Not make battery short circuit Avoid metal thing such as coin pin to insert battery slot 8 Dispose old battery shall avoid pollute environment COPYRIGHT 02006 WITURA CORPORATION SDN BHD 10 WT 209 GSM Wireless Terminal with Fax Function 7 Troubleshooting Problem Solution a Check SIM good insert Failed n rk registerin a b Make sure antenna contact well or pull antenna outside door a Make sure power supply connected to power socket correctly a b Make sure power adapter is good use multi meter when necessary Only free call permitted a Make sure account balance of the SIM card is sufficient a Make sure phone set works properly Ensure the connectivity of telephone line cable b Check network Caller or called party hear nothing a Signal intensity insufficient try moving device position Badvoleequaly b Keep the antenna long away form telephone a Adjust voice volume b Network quality Echo when talking a Try another telephone set No ring tone b Measure the ring voltage with a multi meter a Make sure such SIM Card
4. has Fax feature Cannot fax b Make sure WT 209 normal connect with fax machine Table 7 1 Troubleshooting Sometimes WT 209 may fail in start RUN LED quick flash Please refer to the following table for solution Signal LED Problem Solution 0086 Switch to Data side Pull switch to call side oe o Confirm SIM UIM Card in good C Ot APIECE installation Card slot loose or not 0090 Lock PIN PIN locked please unlock PIN retry e o Lock PIN PIN locked need input PUK to unlock Disable lock function or change old O 8 boneca SIM UIM Card Table 7 2 Failed Start COPYRIGHT 2006 WITURA CORPORATION SDN BHD 11 www discountcomms co uk
5. mode NOTE GSM analogue fax only support auto send receive fax mode It does not support manual reply 3 4 Running Status Specification a b c d e 1 The power LED keeps long time on when connect to external power OFF when use battery After powered module initializations RUN LED quick sparks 0 25s on 0 25s off finish initialization RUN slow flash 1 second on 1 second off indicate device is operational When un insert SIM card or cannot search network NET LED flash per second RUN quick flash when succeeded in registering network NET flashes per 1 5s off 0 5s on The phone indicator indicates the status of telephone connected to the device On when off hook off when on hook Charge on when a call succeeds and off call terminated If wrong number or prohibited number is dialed Du Du busy tone will be heard which means the user should hang up the phone Signal Intensity indicator includes 3 lamps More light on means more strong signal Under proper 1s on 4s off if off over 5s then network may have problem There should be at least 2 lamps to keep light for the device to work properly When fax such 3 lamps indicates fax pages 5 pages is one showed circle as Table 3 2 Pages LED 1 2 3 1 6 11 o o 2 7 12 o 3 8 13 e e 4 9 14 o e r 5 10 15 o O Table 3 2 Fax pages LED status COPYRIGHT 2006 WITURA CORPORATION SDN BHD T WT 209 GSM Wir
6. outgoing call Fax Support T3 0 Fax Max 14400kbps Such Max speed depends on network Caller ID indication Support caller ID indication GSM network access Support GSM network access WT 209 Polarity reverse Send polarity reverse signal for charge Protection Lock SIM card lock PIN etc Keypad NMS Network management over keypad Table 2 1 WT 209 Functions 2 2 Technical Specifications a Working Environment i Operation Temperature 10 C 55 C ii Relative Humidity 10 95 iii Air Pressure 86kPa 106kPa iv Environment noise lt 60dB A b Working Frequency GSM900 GSM 1800MHz automatically select c Frequency Stability Better than 2 5 x 10 d Signal Sensitivity Less than 103dBm e Radiation Power GSM lt 2W f Power Supply AC 220 x 1 15 V g Caller ID Mode DTMF h Telephone Line Length No more than 1000m COPYRIGHT 02006 WITURA CORPORATION SDN BHD WT 209 GSM Wireless Terminal with Fax Function 3 Operation Guide 3 1 Installation Step 1 Insert SIM card into socket Open the back cover insert the SIM card and then restore the back cover Refer to Figure 3 1 Slide the card holder and open it by lifting it up Insert the SIM card into the card holder Make sure that the cut angle is on the right side and the golden connectors on the SIM card are facing downwards Close the card holder and slide it back into its place NOTE The equipment supports only 3
7. 09 GSM Wireless Terminal with Fax Function 1 Overview 1 1 Definitions and Abbreviations GSM Global System for Mobile Communications FXS Foreign Exchange Subscriber DTMF Dual Tone Multi Frequency 1 2 Equipment Description WT 209 GSM Wireless Terminal with Fax Function Refer to as WT 209 in the following sections is a device for voice and analogue fax communication It provides wireless access functionality by GSM network WT 209 is fit for all kinds of areas and scenarios especially in places where wired network is impossible or hard to reach WT 209 is a dual board device which one can support GSM network another can support analogue fax The device provides external interfaces as below a One FXS interface connect to a telephone set b One SIM card slot for SIM card installation c One battery slot d One antenna interface e One program interface connect special program cable for update terminal Figure 1 1 WT 209 GSM Wireless Terminal with Fax Function COPYRIGHT 2006 WITURA CORPORATION SDN BHD WT 209 GSM Wireless Terminal with Fax Function 1 3 LED Indicators 9 Light indicators indicate running state Type Label Color Meaning LED Fee Yellow When incoming outgoing call begin to connect send polarity charging signal light on LED Power Green Light on connect to external power light off when battery works LED Run Green Sparks device under prope
8. Discountcomms Online Store ss GSM Wireless Terminal With Fax Function WT 209 User s Manual www discountcomms co uk WT 209 GSM Wireless Terminal with Fax Function Contents OVER VIEW o cevsnncsedesevedescasedssinns danes LA EEE ESSEE EE E EErEE 1 1 Definitions And Abbreviations ccccce cece ence ence eee eee e nee n een eee enes 1 2 Equipment Description 0 0 cece eceeceeee nent ence eee EE a Ea A AE 1 3 LED Indicators a A a a 1 4 BackPanel La e o E de ta les ts to FUNCTIONS anoeio ee ne e secede coi reinan opindsice saahaeeddeceeaticcccess s 2 1 Main Functions 322 oes yee a dia 22 Technical Specifications s Li laces corked ond on tas geen ves ccs exe OPERATION GUIDEieciciiissiisccosccctscccccccsovessenscsncvessetsessenpececesesecsevasceveses 3 1 Installation 200 A hae Maal a e ee 3 2 Swift DA IR A Se A 3 3 Connect Fax Machine ivi la ll be 3 4 Running Status SpecifiCatiOM oooooccccnccnncnonconcnnoncnnononnoncnnonannananconons 3 5 Connect Fax Machines a e rd ode Keypad Configure Parameter ccccsccscssccsccsccscccccsccsssssccsccsccscesscsssecce Care And Maintenance c ccsccsccsccscccscccccsccscccccsccesccssssscesccscessssccecsseces DE NO 6 1 Battery siii DA avs den da sages o e des 6 2 Battery Specifications A Troubleshooting 3 ccicccsccissccesecvesscsesecedsctveesaecdecssescdeddesddeesseeceesdstesedeesessedes COPYRIGHT 2006 WITURA CORPORATION SDN BHD WT 2
9. ar transmitters with high transmission power and high frequency large current equipments 3 Use electromagnetic shielding methods when necessary For example use the shielded cables 4 The cables should distribute inside the office room so as to protect the equipment from being damaged by high voltage and current caused by thunder Distributing the cables outside is strongly discouraged COPYRIGHT 2006 WITURA CORPORATION SDN BHD 6 WT 209 GSM Wireless Terminal with Fax Function 3 2 Swift Dial Since GSM call is one time send number it will send number after receive all numbers WT 209 will treat has received all numbers and send number after stop dial 5s Also add can treat as received numbers and then no need wait 5s to send numbers 3 3 Connect Fax machine i ii iii iv Connect Fax machine to WT 209 Phone port During GSM network call only can use one channel Voice Data So it only can support auto reply not support manual reply When send Fax dial and destination number For example when need fax to87654321 fax machine then dial 87654321 is swift dial mode When hear fax indicating which means connecting to machine press fax machine start and then can send fax Also can use auto send mode press start after hear ring back tone When receive fax phone ringing off hook hear fax indicating tone then press start then to receive fax It can also use auto reply
10. eless Terminal with Fax Function 3 5 Fax Test WT 209 has pre save 4 pages content Under idle set fax machine as auto reply mode Fax machine off hook will hear dial tone press 91 hear dial tone again then on hook After on hook fax machine ringing receive incoming call 0123456789 auto reply fax Press 91 to fax content WT 209 product profile as Table 3 3 Press Content O1 WT 209 Profile 02H Trouble 03H Keypad Explanation OAH Version OSH Above total 4 pages content Table 3 3 Test Pages Content 4 Keypad Configure Parameter NOTICE Keypad configures parameter set need off hook then on hook and exit parameter will auto save Indicating tone will inform configure success or failure if success then releases dialing tone otherwise release busy tone begin as set begin as cancel Followed two numbers indicate function code function code and content or contents are separated by X digital key 0 9 Functions Parameter Command Specification Adjust incoming call volume H X X indicates incoming call volume from 1 xX 1 5 to 5 1 is lowest and 5 is highest Password is unnecessary for setting you will hear dialing tone if success Adjust outgoing call volume HHXH X indicates incoming call volume from 1 Xx 1 5 to 5 1 is lowest and 5 is highest Password is unnecessary for setting you will hear dialing tone if success
11. r operation On or Off device failed LED Hook Green On telephone off hook Off telephone on hook LED Battery Red On battery is exhausted need rechargeable LED Net Green Indicates connection status Off wireless module not started Sparks quickly network registration not completed Sparks once every 4 seconds network registration succeeded LED Signal Green Indicates signal intensity of the network The more the number 3 indicators of the lighted lamp the stronger the signal intensity of the network Flash standby or calling on 1 second off 4 seconds It indicates faxing under fax mode LED FAX Green Flashes means transmit fax flash speed relate to transmit speed 1 4 Back Panel The back panel of the equipment is shown as in Figure 1 2 a Power DC12v power supply socket Figure 1 2 Back Panel b Power switch DC power switch push down to switch on the equipment c Phone RJ11 telephone set socket connect to telephone set by normal 6P4 phone line d Console Two RJ11 special cable for update terminal e Antenna socket for external antenna COPYRIGHT 02006 WITURA CORPORATION SDN BHD WT 209 GSM Wireless Terminal with Fax Function Ze Functions 2 1 Main Functions Table 2 1 lists the main functions of the equipment Refer to Chapter 3 for more details Functions Specification Notes Voice Provides one FXS interface for connecting to a Communication telephone set for incoming
12. rference with the device s performance Wipe the slightly device with a soft dampened cloth Don t use harsh chemicals cleaning solvents or strong detergents to clean the device Always switch off the device before cleaning The device may generate electromagnetic field don t keep the device in the same place with magnetic storage media such as computer diskettes Don t keep the device under strong sunlight to prevent it from being too hot Don t attempt to connect the device with any other unauthorized devices or equipments Remember to follow any special regulations in force about the using of wireless telephones in any area COPYRIGHT 2006 WITURA CORPORATION SDN BHD 9 WT 209 GSM Wireless Terminal with Fax Function 6 Battery 6 1 Battery Insert Battery slot as Error Reference source not found When change battery terminal shall under off state Figure 6 1 WT 209 Battery Slot 6 2 Battery Specification WT 209 use 1 2 6 V Ni hi battery Ni Hi Battery 1600mAh Ni Hi Battery 2300mAh Max call time 4 hours 6 hours Max standby time 8 hours 12 hours Duration charge to 95 capacity Around 10 hours Around 14 hours 1 Call Standby time will be effected by base station signal and administrators setting parameter When near base WT 209will consume less electricity 2 Battery can recharge several hundred times capacity will
Download Pdf Manuals
Related Search