EQ-505R PREAMP USER`S MANUAL 3Band EQ
Contents
1. EQ 505R PREAMP USER S MANUAL 3Band EQ f EQ 505R HT SE ST 1 Volume g wip VOLUME 2 Bass P 8 PN 3 Middle yl N 4 Treble 1 o 5 Battery check i 5 j 6 Battery check LED A Je BATT Kf 7 Battery box l J D OJ 4 6 3 2 Functions 1 Volume Knob The VOLUME controls the output volume Turned fully counter clockwise it is completely OFF Turned fully clockwise it is LOUD N Bass EQ TONE CONTROL for bass tones 3 Middle EQ TONE CONTROL for middle tones 4 Treble EQ TONE CONTROL for high tones The BASS MIDDLE and TREBLE controls are a 3 band equalizer for controlling tone The BASS and TREBLE tone controls are normal boost cut shelving controls The MIDDLE midrange tone control is a normal boost cut tone filter The center detent on these tone controls yields a flat tone response 12 boosts the tone 12 cuts the tone 5 Battery check 6 Battery check LED Low Battery LED Light The LED will light when the battery has lost power Replace the battery when this light is on This LED light will flash when a cable is connected to the output jack of the pickup system This shows the battery is good 7 Battery A 9 volt battery powers the EQ 505R preamp Before connecting the instrument to an amplifier or mixer please check that2. Fix wire with clip 3 Insert EQ and battery box into hole of guitar 4 Fasten screws properly Out put jack X Cable 5 Put plugs into jacks Solution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens noise or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 6 Installing the pick up 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top of guitar is bended When the pickup is installed to only a part of the groove of saddle back page
3. a fully charged 9 volt battery is connected Specification Features 3Band EQ Input Impedance 2 2MO Frequency Response 20Hz 20KHz Control Range Bass 12dB at 60Hz Middle 12dB at 600Hz Treble 12dB at 10KHz Battery Check S W Battery Life Over 700Hours Power Supply 9V Alkaline Battery Pick up Piezo ceramic pick up Dimension W 42mm X H 95 mm 1 7 X 3 7 Caution The jack should be pluged for proper Preamp working TUNER will works regardless pluging jack There is no output sound please check if tuner or mute is turned on When LCD screen is dim or no display please check battery life To prevent battery loss please unplug jack when preamp is not in use Do not disassemble for repair Return to your dealer for service or repair Do not use too much force when operating the control BELCAT Co Ltd Tel 86 752 355 7545 Fax 86 752 355 2460 ROHS Email belcat belcat com This product complies Internet www belcat com with the RoHS directive INSTALLATION MANUAL 1 Cut out the hole with template Cutting Masking Template 1 Contents Masking A mn 2 Output Jack 3 Pick Up 4 Clip 5 Screw 1 Preamp 2 Tool 4 Electric Drill 4 Router and Grinder eee cutting edge 3mm n 1 2 rey 5 Round File 2 3mm or 3mm and 12mm 3 Phillips Screwdriver 6 Masking Tape i i 7
Download Pdf Manuals
Related Search