user manual
Contents
1. The device is controlled by universal DMX 512 protocol DMX address is the start channel used to receive instructions from the external controller For independent control each fixture must be assigned its unique address control channels For example this device has four channel modes 19 50 18 20 if we set the mode at standard 20 channels mode and there are several models need to be independently controlled we just simply address first fixture at 1 and second fixture at 21 third one at 41 etc fthe devices have the same address they will behave synchronically A Display is flashing when no DMX signal is received More functions RDM RDM stands for Remote Device Management with this function users can realize remote control of the device such as remotely changing DMX address reverse pan tilt setting check a lot of useful information such as temperature power consumption fan speed Etc Every single device has a unique RDM code programmed at manufacture to distinguish from each other It is not recommended for users to change this code Software upgrade function via DMX cable If there is any new firmware for this device it can be upgraded simply via a software upgrade box no need to change any mechanical parts The upgrade box is not included in the package if need any further assistance please just contact your authorized dealer Hibernation The device will enter sleeping mode if activated after a per2. 286 swero a a No funcion hutera 3 6 EC ER Random sob tet swiotst Is ls No uneton ehuteropeny sm ceps A CC ECTS A m9 nmm Inn 7 10 Virtual Color Function Forward Spin 7 eben er moara 9 1 Forward Spin Rainbow Effect Slow gt Fast 0 25 Reverse Spin Rainbow Etfect Slow gt Fas 0 2 EN Continuous amp Color Bounce X Tec Pei li od Gem 2 he a 9 we o faafe Reo Green gt up Buet wntez0 5 45 Beta Green Blue 0 Mite 0 89 130 Black OA gt Ce NP Gen ENT ES e T pio as e Rear Ros O B5 nw 1 12 OenA emos o ess m n s feen Bosw Jols pis 16 12 14 wmn wrom ess pia a7 19 15 zoom smWmgesSgage 9 B5 eme fode 15 18 14 16 Foreground Foreground Color wrm as raz a ae 40 Pate orem 9 5 Co N 5 PatemEffet Effect Slow Fast ee NE Direct access to Pattern of LED 1 amp LED 2 255 ee NE 1 is art ser o 9 mal ieptezen oJ e om ste Green wich o e as ECETIA fofa um e Direct access to Pattern of LED 3 amp LED 4 Byte 2 Pattern Direct access to Pattern of LED 5 amp LED 6 255 Byte 3 Pattern Direct access to Pattern of LED 7 255 Byte 4 Led Off 127 DEN Lem Lol Led On 127 9 Lem te Led Off 127 e v ted Of ter Led Off 127 S nnum Lem Oe wmn Jm 25 Le emm RR HERE hem 7 enn 8 5 LM NN open EU 8 w o EC EE KSE
3. 8bit mode Basic 16bit Basic 16bit mode User User program mode Edit User Max Channel XX Edit users mode PAN CHO1 Calibration 3 Password Password 050 Pan Calibrate channel value Fixture ID Heload Default Name Name Password Password 050 PID Code Set PID of RDM Basic Reload Basic Reload Program Reload Program Reload Password Password 050 Private Reload Private Reload All Reload All Reload PlayO DMX Receive DMX Receive Slave Receive Slave Receive 1 2 3 Choose slave position Sequence Master Alone Run Sequence Music Master Alone Music mode Select Chase Chase Part 1 Chase 1 8 Select and run auto Chase Part 2 Chase 1 8 program Chase Part 3 Chase 1 8 Edit Chase Edit Scenes Scenes Record Chase 1 Chase Test Test Step 01 Beginning scene Chase 8 Step 64 Ending scene Edit Scene 001 Pan Tilt Input manual scene Edit Scene 250 Fade Time Modify fading time Secne Time Modify scene time DMX Input Input scene from exterior controller ScXX gt ScXX Auto Input scenes DMX chart NE name function IO CI a ae se ON E TA cs PR a Normal Normal Sator mode J o Perdonar als mp e ECH Normal Stuer mode wih shutercose o 3 Normal Srutr mode speedsiow fast a2 Em ost Foward suter cose o a Puse elle Reverse shuter Close o 3 Random Skobe shuterCiose o 3 Random Sobe shuter Open 224
4. EVEN LIGHTING WASH MOVING HEAD M7W15RGBW USER MANUAL For safety please read this user manual carefully before initial use Event Lighting reserves the right to revise the manual at any time Information and specifications within this manual are subject to change without notice Event Lighting assumes no liability or responsibility for any errors or omissions Please consult Event Lighting for any clarification or information regarding this item www event lighting com au V1 1 Safety Instructions WARNING Do not open this device there is no user serviceable parts inside Risk of electric shock Do not look at the light source when the device is on CAUTION This unit s housing may be hot during and after operation Install this device in a location with adequate ventilation at least 20 inch 50 cm from adjacent surfaces Do not leave any flammable material within 50 cm of this unit while operating or connected to power Use a safety chain when mounting this device overhead Do not operate this device outdoors or in any location where dust excessive heat water or humidity may affect it Do not operate this device if the housing lenses or cables appear damaged Do not connect this device to a dimmer or rheostat ONLY connect this device to a grounded and protected circuit ONLY use the hanging bracket to carry this device In case of a serious operating problem stop using immediately e The max
5. imum ambient temperature is 104 F 40 C Do not operate this device at higher temperatures Power Input amp Power Linking This device has an auto switching power supply work with input voltage range of 100 240 VAC 50 60 Hz Link up to the maximum 8A DO NOT exceed this Fuse Replacement If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing anticlockwise Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing and fix it Product Installation This device can be mounted in many orientations provided each individual device is secured by the use of correct mounting bracket Use a safety chain when mounting this device overhead Product Appearance Distance m 3 0 3 i Beam opening rm Diameter mi eO LLIX intensity H 15 44 40357 b 4660 Full aud Diameter im 03 95 UX nte sity 00 03 LUX chart Dimensions UN A Oo Jw o Project lens Head Arm Base Display Foot stand Operation button Wireless indicator Mic Left Button Enter Button Down Button Up Button Right Button Fuse Holder Powercon in Power switch Powercon out 3 pin DMX out 3 pin DMX in 9 10 11 1213 14 Menu Ope
6. iod of disconnecting DMX signal to save the power consumption and will return immediately as soon as the DMX signal is sent again Display back up communication IC There is a back up communication IC installed in the display PCB so users could replace at once if the original one is broken Display flip By press up and down button for more than 3 seconds the display will flip automatically this function is useful to read menu conveniently when device is hanged 10 Technical Specifications Input Voltages 100V 240V A 50 60Hz Power Consumption 125W Light source 7 pcs Osram 15W RGBW LED Power Connection Neutrik Powercon input and output connection LED life 60 000 hours Lux 3 500 lumen 9 700 lux RGBW full on 3M at 6 Beam angle 6 to 60 PWM 1 200Hz Colors full color Pixel control Dimmer 0 100 dimmer Strobe 0 5 26 Hz Zoom 6 to 60 Head movement Pan 6301 45 sec or 540 1 2 sec Tile 2650 72 sec 16 bit resolution auto repositioning Control DMX512 3 pin XLR interfaces 19 50 18 20 channel mode Other function wireless DMX is available 24A inch colour LCD display with back up power Thermostat Controlled variable speed fan RDM and software upgrade via DMX Net weight 6Kg A Overall Size 249x179x369mm A Rigging 1pc omega brackets with 1 4 turn quick locks Road case available
7. ration Description of icons in the menu CONNECT LIGHT INFOMATION PROGRAM RH D Menu Default setting shadowed mark with can be basic reloaded be program reloaded can be private reloaded DMX Address XXX DMX address setting Max Temperature 80 139 C 90 C 176 282 F Lamp switch off when O temperature continuously over for 5 minutes Lamp Adjust Adjust value of each Fixture Life XXXX Hours Fixture total run time Near Lamp Temp depends on fixture Channel Value Error Message trorcchannels Fixture Model M7W15RGBW Display brand and model Software Ver 1U01 V1 0 00 Version of each IC 2U01 V1 0 00 Reset All Reset all Pan amp Tilt Reset Pan amp Tilt Others Reset Others Pan Reverse Pan Reverse Tilt Reverse Tilt Reverse Pan Degree Choose Pan Degree Movement Encoders Encoder wheel on off Pan Tilt Mode Choose pan tilt mode Mic Sens Sensitivity of Mic No Signal Mode when no signal Ul Set Temperature C FO Fahrenheit Celsius Temperature at C F Fans Mode Auto Speed High Speed Fans mode Hibernation OFF 01M 99M 15M Sleeping mode Backlight 02 60m 02m Show backlight time Flip Display ON OFF Display 180 reverse Display Bright 00 31 10 Display Brightness Brand Show Show brand or not Program Key Lock Key lock on off LanguageO En f amp S Fr Sp Language Select Users User Mode Standard mode Extended Extended mode Basic 8bit Basic
Download Pdf Manuals
Related Search