Home

Admin PM-V2-Modified

1. July 2010 PGM 191 Flex Description Default Values Circular Terminal Btn Enable Disable Overflow 7 When assigned calls to a station in the group queue until answered or each station Not assigned 1 Station Destination in the group has been tried The call remains at the last station in the group or 2 Hunt routes to the overflow destination after the Overflow timer Flexible button 8 expires 3 VMIB 00 70 00 disable 4 System Speed 2000 2499 Overflow Timer 8 This parameter sets the interval a call will queue to a group before routing to the 180 seconds 000 600 in 1 Overflow destination Flexible button 7 second increments Wrap up Timer 9 This parameter sets the duration a station remains unavailable after completing a 002 seconds 000 999 in 1 call second increments No Answer Timer 10 This parameter sets the duration a station receives ring before the call is routed to 15 seconds 00 99 in 1 second the next idle station in the group increments Pilot Hunt 11 If this parameter is enabled On calls to a member that are not answered route to 1 On 0 Off the Hunt Group A circular terminal hunt group can be assigned with a pilot number 1 so that only calls to the pilot number route to the Hunt Group Alt If No Member 12 When enabled if a member is not on duty intercom calls drop and CO 0 Off 0 Off incoming calls route to the assigned Alternate destinat
2. Procedure 1 Press the TRANS PGM button 2 Dial 106 3 Select the desired Flexible button from the chart below 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 106 Btn Station Group 1 620 629 Non conflicting 2 to 4 Pilot Range digits 0 9 Internal Page 2 501 510 Zone Range Internal All Call 3 543 Page Meet Page 4 544 5 545 Zone All Call Page 6 549 Internal External SMDR Account 7 550 Code Flash Command 8 551 14 Flex Description Default 106 Btn to CO Line SLT Last Number 9 552 Redial LNR Do Not Disturb 10 553 Call Forward 11 554 Speed Dial 12 555 Program MSG Wait Call 13 556 Back Enable MSG Wait Call 14 557 Back Answer Speed Dial 15 558 Access Cancel 16 559 DND CFW Pre Selected MSG SLT Hold 17 560 Virtual Mailbox 18 200 249 Reserved 19 SLT Program 20 563 Mode Select ACD Reroute 21 564 15 Values Issue 2 0 July 2010 Issue 2 0 July 2010 3 1 7 Flexible Numbering Plan B PGM 107 PGM 107 is one of three 3 PGMs that assign dial codes for access to features and functions of the ip 60 60 Also see PGMs 106 and 109 Procedure 1 Press the TRANS PGM button 2 Dial 107 3 Select the desired Flexible button from the chart belo
3. Flex Description Default Values 142 Btn Reverse NPR Line Drop CPT 4 If this parameter is On the system monitors incoming CO line calls if after answer 0 Off 0 Off Call Progress dial tone is detected the CO line is dropped Thus a station cannot receive dial 1 tone as a transfer and defeat Toll Restriction CO Distinct Ring 5 CO lines can be assigned one of 5 ring tones for incoming calls When different ring 0 0 4 tones are assigned to each CO line the ringing CO line can be determined from the tone CO Line MOH 6 CO lines may be assigned separate sources for MOH overriding the system wide 1 Internal Music 0 Not assigned assignments in PGM 171 When the CO Line MOH here is Not assigned 0 the 1 Internal Music assignments in PGM 171 apply to the CO line 2 External Music 3 Reserved 4 8 SLT 1 5 9 Hold Tone Supply PABX CO 7 In some cases the PABX or PSTN may not provide certain tones to the CO line In No PABX CO Yes ip 60 60 Dial Tone this case the ip 60 60 can provide these tones to the station in place of the CO No PABX CO Supply PABX CO 8 line When this parameter is assigned Yes the ip 60 60 provides the tone No PABX CO Yes ip 60 60 Ring Back Tone otherwise the PABX or PSTN is expected to provide the tone Select the desired No PABX CO Supply PABX CO 9 Flexible button for the specific Tone No PABX CO Yes ip 60 60 Error Tone
4. Alarm Contact 2 This parameter defines the contact state open or close that activates the Alarm 1 Close 0 Open Type signal 1 Close Alarm Mode 3 This parameter determines the operating mode of the contact Alarm or Doorbell 1 Alarm 0 Doorbell 1 Alarm Alarm Signal 4 This parameter determines if the Alarm signal is a single or repeating tone Usersto 1 Repeat 0 Once Mode receive the Alarm signal are defined in PGM 113 Flexible button 10 1 Repeat 88 Issue 2 0 July 2010 3 5 5 System amp Main Attendant Assignments PGM 164 PGM 164 configures the System and Main Attendants for the system Procedure 1 Press the TRANS button 2 Dial 164 3 Select the desired Flexible button Note attendants must be entered in order 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values ia System Attendant 1 This parameter defines the System Attendant 100 DKT station number Main Attendant 1 2 This parameter defines the first Attendant To delete Main Attendant press Not assigned DKT station number the Speed button Main Attendant 2 3 This parameter defines the second Main Attendant To delete a Main Attendant Not assigned DKT station number press the Speed button Main Attendant 3 4 This parameter defines the third Main Attendant To delete a Main Attendant press
5. 1 1 1 4 Admin Reference Charts err reis 1 1 45 Quick Reference Chants ur e enters 1 2 ADMIN PROGRAMMING nnn 2 2 1 Program GROUPS iioii 2 2 2 Digital Key Telephone 2 2 2 1 Entering the POM 2 2 2 2 Navigation arid BUGIS sox ope 3 2 2 3 Entering and Saving Data rc D ee 3 2 2 4 RESCUING System oc 2 2 9 Initial Setup uen 4 3 ADMIN PROGRAMMING PROCEDURES eene 5 3 1 Basic Set up 100 109 1 5 2111 POM M US 5 3 1 2 Board Assignment PGM 101 iens er n ee eae 8 3 1 3 Logical Slot Assignment 103 10 3 1 4 Numbering Plan 104 0 0 00000 11 3 1 5 Flexible Station Numbering Plan 105 12 3 1 6 Flexible Numbering Plan 106 14 3 1 7 Flexible Numbering Plan B 107 16 3 1 8 System IP Setup 108 Stt cecidi aed bu 18 3 1 9 Flexible Numbering Plan
6. Description Stations in a Tenancy Group are allowed or denied the ability to call stations in other Tenancy Groups The Flexible button toggles access and the LED indicates access On allowed access Off access not allowed Default No assignment Values Flexible button 1 5 45 Issue 2 0 July 2010 3 2 12 Call Forward Preset 121 PGM 121 defines the Preset Call Forward destination for each station Calls are sent to the destination which can be another station or a Station Hunt Group when the Preset Call Forward timer PGM 181 Flexible button 12 expires Procedure Press the TRANS PGM button 1 Enter the appropriate Station Range Description This parameter defines the destination for Preset Call Forward If the station does 2 Dial 121 3 4 Enter the destination Dial 1 and a station number or Dial 2 and a Station Hunt Group 5 Press the Hold Save button PGM Flex 121 Btn Preset Call Forward not answer an incoming CO call within the Preset Call Forward timer PGM 181 Flexible button 12 the call is sent to the assigned station or Station Hunt Group Default No assignment Values 1 station number 2 Hunt Group 46 Issue 2 0 July 2010 3 2 13 Idle Line Selection PGM 122 122 defines the Idle Line Selection for the station The defined Idle Line Selection is accessed when the station goes Off hook Idle Line Selection c
7. used External Night 7 If this parameter is On when an incoming CO call is received and UNA service is 0 Off 0 Off Ring activated alerting will be sent to the LBC contact 1 Hold Preference 8 This parameter defines the preferred type of Hold System anyone with an 1 System 0 Exclusive appearance may access the held call or Exclusive only the holding station can 1 System access the held call Multi line 9 When enabled On the system will allow multiple parties up to 14 in a conference 1 On 0 Off Conference 1 Print LCR 10 This parameter determines if the DKT LCD and SMDR will show the digits dialed by O Off 0 Off Converted Digit LCR On or the originally dialed digits Off 1 11 If this parameter is On when a member joins a Conference Room existing 1 On 0 Off Warning Tone members hear a warning tone 1 Off net Prompt 12 If this parameter is On the Off net VMIB prompt is heard when a call is forwarded 1 On 0 Off Usage over a CO line 1 Off net DTMF 13 This parameter determines if DTMF tones are returned to a caller on a CO line when 1 On 0 Off forwarded Off net 1 Voice Path 14 This parameter determines if a voice path to an outgoing CO line is set up 0 After dialing 0 After digits Connect immediately IMM or after dialing the first digit DGT when a CO line is assigned for 1 Immediate PBX
8. Phone TX to ACO 33 00 63 6 RSG Phone TX to CTR ACO 22 00 63 7 RSG IP Phone TX to DCO 33 00 63 8 RSG Phone TX to 29 00 63 205 Issue 2 0 July 2010 3 14 Nation Specific Gain Tone Tables PGM 400 424 PGMs 400 to 423 establish audio gain levels and tone frequencies Defaults are based on the Country code Procedure 1 Press the TRANS button 2 Dialthe PGM number 400 423 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 400 DTIB Gain Btn 1 DTIB DTIB 30 00 63 2 DTIB SLIB 39 00 63 3 Reserved 4 DTIB WTIB 26 00 63 5 DTIB ACOB 22 00 63 6 Reserved 7 DTIB DCOB 33 00 63 8 DTIB VMIB 29 00 63 9 DTIB DTMF 08 00 63 10 DTIB TONE 22 00 63 11 DTIB MUSIC1 29 00 63 12 DTIB MUSIC2 29 00 63 13 Reserved 206 Description Issue 2 0 July 2010 PGM Flex Default Values 401 SLIB Gain Btn 1 SLIB DTIB 32 00 63 2 SLIB SLIB 32 00 63 3 Reserved 4 SLIB WTIB 32 00 63 5 SLIB ACO 32 00 63 6 Reserved 7 SLIB DCO 44 00 63 8 SLIB VMIB 40 00 63 9 SLIB DTMF 28 00 63 10 SLIB TONE 28 00 63 11 SLIB MUSIC1 40 00 63 12 SLIB MUSIC2 40 00 63 13 Reserved PGM Flex De
9. 109 2222 1 20 3 2 Station PGM 110 131 21 3 2 1 Station Id Name amp DSS DLS Map PGM 110 21 3 2 2 Station Attributes pe e DIE bes SER Hoe lb chius 24 3 2 9 Station Attributes I PGM 112 rna it 27 3 2 4 Station Attributes IIl PGM T neant 30 3 2 5 Station Attributes IV 114 33 Issue 2 0 July 2010 3 2 6 Flexible Button Assignment 115 36 3 2 7 Station Class of Service COS 116 39 3 2 8 Line Group Access oder aetatem 41 3 2 9 Internal Page Zone PGM ito ert rebelde 42 3 2 10 Conference Page Zone Access 119 43 3 2 11 Intercom Tenancy Group 120 040000 44 3 2 12 Call Forward Preset PGM 2T inei ac dentes 46 3 2 13 Idle Line Selection PGM 122 rase nete ioco 47 3 2 14 SMDR Account Group 124 enne 48 3 2 15 Copy DSS Button PGM 125 uid oi ean ute siis 49 3 2 16 Station IP List 126 i iecit eit tees Lead 50 3 2 17 Station Mailbox Attributes 127 51 3 2 18 Virtual Mailbox Attributes 129 5
10. 229 5 Table 231 Flexible DID Table 232 System Speed Zone 233 Weekly Time Table 234 Voice Dialing Table 236 Mobile Extension 237 Incoming CLI destination table 238 Voice Mailbox COS Table 224 Issue 2 0 July 2010 250 Hot Desk Agents SMS ATTRIBUTES 291 SMS SETTING 292 SMS CO ATTRIBUTE NETWORKING 320 Networking Basic Attribute 321 Networking Supplementary Attribute 322 Networking CO Line Attribute 324 Networking Routing Table VOIB 340 IP Setting 341 Setting Not Supported yet ATTRIBUTES 500 Attributes 1 501 Attributes 2 RSG IP PHONE 380 Slot For RSG IP 381 RSG P No Assign 382 Attribute 386 Phone Attribute 396 IP Phone RX GAIN 397 IP Phone TX GAIN 400 Rx Gain Control 401 Rx Gain Control 402 DTIB Spkr Gain Control 404 ACOB Rx Gain Control 406 Rx Gain Control 407 VMIB Rx Gain Control 408 DTMF Receiver Rx Gain Control 409 T Page Rx Gain Control NATION SPECIFIC 225 Issue 2 0 July 2010 410 Rx Gain Control Modem Rx Gain Control 412 Short SLIB Gain Control 413 Long Gain
11. Programming mode 1 1 3 Admin Programming Procedures Section 3 provides detailed procedures to access each of the Programs using a DKT It includes detailed but brief descriptions of each PGM parameter as well as the North American default values and range of values that a parameter can accept 1 1 4 Admin Reference Charts Section 4 is an index for quick reference to the various PGMs available in the ip 60 60 Also in this section are the codes for the eight 8 default Flexible System Numbering Plans 1 1 5 Quick Reference Charts Section 5 provides reference charts for use in station programming for the user and Attendant In addition reference charts are provided for the Flexible button assignment Issue 2 0 July 2010 2 ADMIN PROGRAMMING OVERVIEW Admin programming is the process of configuring the ip 60 database to address the needs and concerns of the end user ip 60 60 is an extremely flexible system permitting a high level of customization Admin programming is accomplished from an assigned Digital Key Telephone DKT default Station 100 or using the more graphical user interface of the ip 60 60 PC Admin This manual provides descriptions for each of the programmable parameters of the ip 60 60 including the default and valid range of values for the parameter In addition this manual provides detailed step by step instructions for modifying parameters using a DKT For instructions using ip 60 PC Admin please
12. 255 in 100 mill Timer or DISA DID CO call After the timer expires the call is routed based on the second increments received digits CO Call Drop 16 This parameter sets the duration a Prepaid or Unsupervised Conference call remains 10 seconds 00 99 in 1 second Warning Timer connected after receiving Call Drop Warning Tone After this timer expires the call increments 117 Issue 2 0 July 2010 PGM Flex Description Default Values 180 Btn drops Also see Flexible button 22 Reserved 17 CO Dial Delay 18 This parameter defines a delay before dialed digits are sent by the system over 01 100 milli 00 99 in 100 mill Timer analog CO PBX lines Due to slow response of certain PSTN and PABX circuits it is seconds second increments possible to begin dialing before the circuit is ready to accept and register digits In order to minimize restricted dialing and misdialing any digits dialed prior to the timer expiration are buffered and sent when the delay timer expires CO Release 19 This parameter determines the duration a CO line will remain unavailable after 020 2 seconds 001 150 in 100 mill Guard Timer disconnect to allow the network to clear down the call second increments CO Ring Off 20 This parameter sets the maximum Ring off signal before the call is considered 060 6 seconds 010 150 in 100 mill Timer abandoned The ip 60 considers shorter periods a continuatio
13. No 1 Yes 18 If this parameter is enabled On calls on a CO connected to another CO line 1 On 0 Off Detect are dropped and the CO lines returned to idle if busy or error tone is detected 1 LD Delay Count 19 In some cases the PSTN may require a delay when setting up LD calls This 0 no delay 0 5 1 parameter sets the duration the system will delay dialing after LD code is sent to increments the PSTN Dial Pad Character Chart 1 10 2 20 3 30 21 D 31 Q 11 B 22 32 2 542 66 Issue 2 0 July 2010 G 41 42 1 43 7 70 71 R 73 S 74 x Blank x1 U x2 67 Issue 2 0 July 2010 3 34 ISDN IP CO Line Attributes 143 PGM 143 assigns attributes associated with ISDN or VoIP to the CO line range Procedure 1 Press the TRANS PGM button 2 Dial 143 3 Enter the appropriate CO line Range 4 Select the desired Flexible button For Numbering Plan Id Flexible button 8 select Flexible button 1 for Calling or Flexible button 2 for Called numbers ge Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 143 Btn COLP Table 1 This parameter defines the index to the COLP Table PGM 201 used to determine Not assigned 00 50 Index the COLP sent by the system If the index is 50 the COLP is determined from PGM Delete so
14. SIP User ID 23 This parameter determines the caller id for a station when employing SIP for a call 00 00 16 Table Index When using SIP the caller id is based on the CLIP COLP PGM 143 Flexible button 1 and 2 or the User ID defined from the SIP User ID Table index PGM 501 entered here Redial DTMF 24 When enabled the station receives DTMF tones during Redial 1 On 0 Off 1 26 3 2 3 Station Attributes 112 PGM 112 is one of four 4 program groups that assign general attributes to the station range Also see PGMs 111 113 and 114 Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial 112 3 Enter the appropriate Station Range 4 Selectthe desired Flexible button from the chart below 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 112 Btn CO Warning 1 When enabled On the station user will receive a warning tone indicating the call 0 Off 0 Off duration exceeds the CO Warning Tone time 180 Flexible button 22 The 1 tone is repeated at intervals of the CO Warning tone time Automatic Hold 2 When enabled pressing a CO line button while on a CO line call places the 1 On for Atd 0 Off active CO line on hold and accesses selected CO line Off for others 1 On CO Call Time 3 If this parameter is enabled On an outgoing CO line
15. packets Codec Type 5 This parameter defines the default codec used by the system for a VoIP connection 1 G 711 u Law 0 6 711 ALAW A different codec may be selected during the call set up negotiation 1 6 711 ULAW 2 G 723 1 3 729 4 729 200 Issue 2 0 July 2010 Flex Description Default Values 382 Btn First Access RSG 6 When enabled On the station accesses the CO line connected to the RSG by 1 On 0 Off CO dialing the CO Line access code for the 1 available CO group ex 9 The RSG is 1 not supported ip 60 60 Ring without CO 7 When enabled stations attached to the RSG will ring for incoming calls even if not 1 On 0 Off Ring Assign assigned CO Ring PGM 144 The RSG is not supported in ip 60 60 1 201 3 13 4 IP Phone Attributes 386 Issue 2 0 July 2010 PGM 386 defines the MAC address of IP Phones allowed to register and displays attributes of registered IP Phones Procedure 1 Press the TRANS button 2 Dial 386 3 Enter the Table index 01 16 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 386 Btn Set MAC 1 This parameter defines the MAC address of each IP Phone up to 16 the ip 60 60 00 00 00 00 00 12 hex digits 0 F Address should register to the system 00 IP Address 2 This Flexible bu
16. 1 Executive Grade 4 This parameter determines if an Executive can make intercom calls to other 1 highest grade 01 12 Executives even if the called Executive is in DND Executives can call other 1 Highest level Executives of the same or higher grade overriding Executive Secretary Forward 12 Lowest level ICM Call To 5 When enabled the system routes all Intercom for the Executive to the 0 Off 0 Off Secretary Secretary station 1 164 Issue 2 0 July 2010 3 9 8 Flexible DID Conversion Table PGM 231 PGM 231 defines the Type 2 DID destinations for various ring service modes Procedure 1 Press the TRANS button 2 Dial 231 3 Select Flexible button 1 to input a DID Destination Select Flexible button 2 to initialize the DID Conversion Table or Select Flexible button 3 to delete all DID Table entries 4 Forinputto the table enter the DID Table index 000 999 5 Select the desired Flexible button 6 Enter the appropriate value 7 Pressthe Hold Save button PGM Flex Description Default Values 231 Btn DID Name 1 This parameter assigns a name up to 12 characters for the DID Conversion Table Not assigned 11 characters see Dial index Pad Character Chart Day Destination 2 This parameter defines the Flexible DID Conversion route for Day mode service Not assigned 01 12 see DID Destination Chart below Night Destination 3 This parameter d
17. 1 SMDR 7 This parameter establishes the port for Trace data output 01 1 Debug 8 This parameter establishes the port for Debug data output 01 1 PC ADMIN 9 ip 60 60 automatically selects the PC Admin port no entry required Auto PC Attendant 10 This parameter establishes the port for a PC Attendant connection 08 Net PC Attd 01 COM 1 02 COM2 107 Issue 2 0 July 2010 PGM Flex Description Default Values 175 Btn 08 Net PC Attd CTI 11 This parameter establishes the port for a CTI data connection 09 Net CTI 01 COM 1 02 COM2 09 Net CTI 108 Issue 2 0 July 2010 3 5 17 Pulse Dial Ratio PGM 176 PGM 176 establishes the analog CO line out pulse dial close to open ratio 60 40 or 67 33 Procedure Press the TRANS PGM button Dial 176 Select the desired Flexible button Enter the appropriate value Press the Hold Save button enc ul PGM Flex Default Values 176 Btn Pulse dial ratio Description This parameter defines the close open ratio for dial pulses on an analog CO line 1 67 33 0 260 40 1 67 33 109 3 5 18 SMDR Attributes 177 PGM 177 defines characteristics for SMDR outputs and LD call definition Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial 177 3 Select the desired Flexible button 4 Enterthe
18. 3 SLT MOH 3 101 Issue 2 0 July 2010 PGM Flex Description Default Values 171 Btn 4 SLT 4 5 SLT 5 Internal 8 This parameter selects the melody used for Internal select from 13 available 0 Romance 0 Romance melodies 1 Turkish March 2 Green sleeves 3 Fur Elise 4 Carmen Toreador Song 5 Waltz of the Flowers 6 Pavane 7 Sichilland 8 Mozart Piano Sonata 9 Song of Spring 10 La Campanella 11 Overture No 2 Badinerie 12 Blue Danube 102 Issue 2 0 July 2010 3 5 13 PBX Access Codes 172 PGM 172 assigns up to four 4 PBX Trunk Access codes used by the ip 60 60 when installed behind a PBX Centrex Procedure Press the TRANS PGM button 2 Dial 172 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 172 Btn 1 4 This parameter defines up to four 4 PBX Trunk Access codes used by ip 60 60 to Not assigned 0 9 Code determine when to activate COS on lines installed behind a PBX Centrex 103 Issue 2 0 July 2010 3 5 14 PLA Priority Setting 173 PGM 173 defines the priority of incoming calls for Priority Line Answer Procedure 1 Press the TRANS PGM button 2 Dial 173 3 Select the desired Flexible button 4 Enter the appropriate
19. 4 Enterthe desired Account Group 00 23 5 Press the Hold Save button PGM Flex Description Default Values 124 Btn This parameter assigns the station to an Account Group that is output as part of the 00 no group 00 23 SMDR Account Group 48 Issue 2 0 July 2010 3 2 15 Copy DSS Button 125 PGM 125 permits the Flexible button configuration of a station to be copied to other stations or all stations in an Intercom Tenancy Group see PGM 120 Procedure 1 Press the TRANS PGM button 2 Dial 125 3 Enter the copy from station number 4 Press Flexible button 1 to copy to a station or Press Flexible button 2 to copy to all stations of a Tenancy Group Enterthe desired copy to station or Tenancy Group number 6 Press the Hold Save button PGM Flex Description Default Values 125 Btn Copy DSS Button 1 Flexible button 1 copies Flexible buttons to another station Station number 2 Flexible button 2 copies Flexible buttons to all stations Tenancy Group Tenancy Group number 1 5 49 Issue 2 0 July 2010 3 2 16 Station IP List PGM 126 126 defines the IP address of a station for 1 party CTI call control when employing a LAN connection Procedure Press the TRANS PGM button Dial 126 Enter the station port number 01 48 Enter the desired IP address Press the Hold Save button IES enc Iul PGM Flex Defaul
20. E1 T1 PRI used to 0 0 0 0 IP v4 IP address upgrade the board firmware when required XXX XXX XXX XXX DCO Gateway IP 4 This parameter defines the default gateway IP address for the digital CO board 0 0 0 0 IP v4 IP address Address E1 T1 PRI used to upgrade the board firmware when required XXX XXX XXX XXX 79 Issue 2 0 July 2010 PGM Flex Description Default Values 155 Btn DCO Subnet 5 This parameter defines the subnet mask of the digital CO board E1 T1 PRI used to 0 0 0 0 IP v4 IP address Mask upgrade the board firmware when required XXX XXX XOOCXXX Reserved not used DCO Master This parameter determines the master clock for the digital CO board When set to 0 Slave 0 Slave Clock slave the board will derive the clock signal from the connected circuit When set to 1 Master master the digital CO board will employ the local clock as the master clock signal and expects the connected circuit to synchronize to the clock PLL SSCG 8 not used T1 Setup mode 9 This parameter assigns the type of framing for the T1 circuit as D4 or ESF 0 D4 0 D4 1 ESF T1 Line Mode 10 This parameter assigns the Line coding for the T1 circuit as B8ZS or AMI 0 B8ZS 0 B8ZS 1 AMI 80 3 5 System Data PGM 160 184 3 5 1 Procedure System Attributes PGM 160 PGM 160 defines general system attributes 1 Press the TRANS PGM button Issue 2
21. PGM Flex Description Default Values 410 CPT Gain Btn 1 Call Progress Tone ACOB 32 00 63 2 Reserved 3 Call Progress Tone DCOB 32 00 63 PGM Flex Description Default Values 411 Modem Gain Btn 211 Issue 2 0 July 2010 Flex Description Default Values 411 Modem Gain Btn 1 20 00 63 2 Reserved 3 Modem DCOB 24 00 63 PGM Flex Description Default Values 412 Short SLIB Btn Gain 1 Short SLIB Short ACO Intended for SAF only 32 00 63 2 Short SLIB Long ACO Intended for SAF only 32 00 63 PGM Flex Description Default Values 413 Long SLIB Btn Gain 1 Long SLIB Short ACO Intended for SAF only 32 00 63 2 Long SLIB Long ACO Intended for SAF only 32 00 63 PGM Flex Description Default Values 414 Far SLIB Btn Gain 1 Far SLIB Short Intended for SAF only 32 00 63 2 Far Long ACO Intended for SAF only 32 00 63 212 Issue 2 0 July 2010 Flex Description Default Values 415 Short ACO Btn Gain 1 Short ACO Short SLIB Intended for SAF only 32 00 63 2 Short ACO Long SLIB Intended for SAF only 32 00 63 34 Short ACD Far SLIB Intended for SAF only 32 00 63 4 Short ACO DTIB Intended for SAF only 26 00 63 PGM Flex Description Default Values 416 Long ACO Btn Gain 1 Long ACO Short SLIB Intended for SAF only 32 00 63 2 Long ACO Long
22. When set to No the Intercom and line ring cadences are reversed Reserved 8 ACD Print Enable 9 When enabled On ACD Automatic Call Distribution Statistics are output at an 0 Off 0 Off interval defined by Flexible button 10 and 14 1 ACD Print Timer 10 This parameter defines the time between outputs of the ACD Statistics Flexible 001 001 225 button 9 from 001 to 225 units where the units seconds or hours are defined by Flexible button 14 ACD Clear 11 When enabled On the system will clear data from the ACD statistics after output of 0 Off 0 Off Database after ACD reports 1 Print VIMB Prompt 12 This parameter determines the gain used for playback of VMIB announcements 08 00 31 Gain CLI Information 13 When enabled On the system will send the associated with the call to the 0 Off 0 Off at VM SMDI external VM if SMDI signaling is enabled DIP SW 1 position 2 Not available in 1 ip 60 60 ACD Print Timer 14 This parameter defines the unit of measure for the ACD Print Timer Flexible button 0 Seconds 0 Seconds Unit 10 1 Hours Set VM SMDI 15 This parameter determines if SMDI signaling for an external Voice Mail is Type I or 0 7 Typel Type Type Il Not available ip 60 60 1 Type Il Incoming Toll 16 When enabled On the system will apply COS should the user dial after answering O Off 0 Off Check an incoming CO line call 1 17 Th
23. default 147 decrementing the station number by one for each agent to the Number of Agents assigned Default 00 Values 00 46 View Agent Range N A N A Auto Logout The system will log an agent out after the pre defined Auto Logout timer The timer is set in 24 hours and if set at 00 the Logout feature is disabled 00 24 hours 176 3 10 SMS Attributes 291 292 3 10 1 SMS Setting PGM 291 PGM 291 configures the SMS Message Center telephone number and CLI Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 291 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 291 Btn SMS Center 1 This parameter assigns the telephone number the SMS Message Center to Not assigned Up to 16 digits Number receive an SMS from the ip 60 SMS Center CLI 2 This parameter defines the CLI the ip 60 will receive from the SMS Message Center Not assigned Up to 16 digits when a new SMS is received 177 Issue 2 0 July 2010 3 10 2 SMS Line Attributes 292 PGM 292 assigns CO lines and stations to receive external SMS messages Procedure 1 Press the TRANS button 2 Dial 292 3 Enter the CO line range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex
24. loss of RTP packets second increments long jitter buffer may result in excessive delay Voice Monitor 17 When enabled the system will monitor the RTP traffic to from the VOIB 0 Off 0 Off 1 323 Fast 18 When enabled the system will implement the H 323 Fast call set up mode 0 Fast 0 Fast Mode 1 Normal Early H 245 19 When enabled the system will employ the Early H 245 channel set up 0 Off 0 Off operation for H 323 1 H 245 Tunneling 20 When enabled On the system will implement tunneling of H 245 messages QSig 0 Off 0 Off messages 1 TOS Precedence 21 This parameter defines the setting for bits 0 2 of the IP TOS byte Precedence can 0 0 7 be set from 0 the lowest precedence to 7 the highest precedence FAX Mode 22 When enabled On the system implements T 38 IP FAX detection using the 0 Off 0 Off receiver Re Invite message Otherwise the initial Invite contains the T 38 1 parameters Dial Pad Character Chart 188 1 43 1 53 0 63 7 70 P 71 Q 72 R 73 S 74 0 oo Blank 1 kD 3 189 Issue 2 0 July 2010 Issue 2 0 July 2010 3 12 2 GateKeeper Settings 341 341 configures the system to match the H 323 GateKeeper characteristics Procedure 1 Press the TRANS button 2 Dial 341 3 Select the desired Flexible button 4 Enterthe appropriate
25. second increments VMIB Announce 6 When enabled On the ip 60 will repeat the VMIB Announcement 2 Flexible 0 Off 0 Off 2 Repeat button 4 at intervals Flexible button 5 to queued calls 1 Overflow 7 When assigned calls to a station in the group queue until answered or each station Not assigned 1 Station Destination in the group has been tried The call remains at the last station in the group or 2 Hunt routes to the overflow destination after the Overflow timer Flexible button 8 expires 3 VMIB 00 70 00 disable 4 System Speed 2000 2499 Overflow Timer 8 This parameter sets the interval a call will queue to a group before routing to the 180 seconds 000 600 in 1 Overflow destination Flexible button 7 second increments Wrap up Timer 9 This parameter sets the duration a station remains unavailable after completing a 002 seconds 000 999 in 1 call second increments Alt If No Member 10 When enabled if a member is not on duty intercom calls drop and CO 0 Off 0 Off incoming calls route to the assigned Alternate destination Flexible button 13 1 Music Source 11 This parameter determines if a queued caller receives Ringback tone or MOH 0 0 7 Not assigned 1 Internal Music 2 External Music 134 Issue 2 0 July 2010 PGM 191 Flex Description Default Values ACD UCD Btn 3 Not ip 60 60 4 8 SLT
26. the DKT is in the Program mode and can access the various PGMs and parameters Specific instructions for each parameter are provided in the Admin Procedures given in section 3 To access a specific PGM while in the Program mode 1 Press the TRANS PGM button 2 Dial the 3 digit code 2 2 2 Navigation and Buttons While in the Program mode the Volume Up Down can be used for navigation through the PGM sections Other buttons on the DKT also provide special functions during Admin Programming The BACK softkey or CONF button if assigned move back one step in the process The DELETE softkey or the SPEED button deletes the current entry The SAVE softkey or the Hold Save button store an entry to the system database A value must be saved with the SAVE softkey or Hold Save button prior to moving to another parameter 2 2 3 Entering and Saving Data In most cases after selecting a PGM a specific parameter is selected using a Flexible button and a value entered with the dial pad When a value is saved the system will verify the value is in range and does not conflict with other parameter settings If the data value is valid confirmation tone is received If the value is not valid error tone is received and a valid value can be entered without further action In some cases after selecting a PGM the Flexible buttons are used to toggle a parameter value In this case the value is not checked since the Flexible button on
27. the station is allowed to intrude on other busy stations 0 Off 0 Off Supervisor force a busy CO line to idle disconnecting any active call 1 29 3 2 4 Station Attributes 113 PGM 113 is one of four 4 program groups that assign general attributes to the station range Also see PGMs 111 112 and 114 Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial 113 3 Enter the appropriate Station Range 4 Selectthe desired Flexible button from the chart below 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 113 Btn 1 When enabled the station is permitted access to System Admin The station must 1 Enable at 0 Disable DKTU Only be a DKTU and a 24 button phone is recommended 0 Disable at 1 Enable other stations VMIB Access 2 When enabled the station user can access the VMIB and the user is assigned a 1 Enable 0 Disable VMIB Voice Mailbox 1 Enable Group Listening 3 When enabled pressing the On Off button of the station while on a handset call 1 Enable 0 Disable activates the speaker so others in the vicinity hear the voice of the connected user 1 Enable Only the handset microphone is active Override 4 When enabled the station user is allowed to signal a station on a CO line call 0 Disable 0 Disable Privilege 1 Enable SMDR
28. 0 July 2010 2 Dial 160 3 Press the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 160 Btn Attendant Call 1 If this parameter is RBT Ring Back Tone is provided to the station when calling a 0 MOH 0 MOH Queue Ring busy Attendant otherwise hold tone or VMIB MOH is provided as defined in PGM 1 Ring Back Tone Back MOH 171 Flexible button 2 Camp on Call 2 If this parameter is RBT Ring Back Tone is provided to the camped on party 0 MOH 0 otherwise is provided 1 RBT CO Line Choice 3 This parameter defines the method the system will use to secure a CO line from a 1 Last 0 Round Robin CO Group Last highest numbered or Round Robin 1 Last DISA Retry 4 This parameter determines the number of times a DISA caller can retry dialing a 3 0 9 Counter station or feature code before being routed to the DID DISA Destination PGM 167 ICM Continuous 5 This parameter determines if Intercom dial tone is continuous or interrupted 1 continuous 0 Discontinuous Dial Tone discontinuous 1 Continuous 81 Issue 2 0 July 2010 PGM Flex Description Default Values 160 Btn CO Dial Tone 6 When enabled the system uses dial tone detection when a pause is detected in a 0 Off 0 Off Detect Speed Dial number otherwise the Pause timer PGM 181 Flexible button 11 is 1
29. 0 July 2010 3 2 7 Station Class of Service COS PGM 116 PGM 116 assigns a Class of Service to stations The COS for a particular call is determined by the Station COS and the CO line COS PGM 141 Flexible button 2 Procedure 1 Press the TRANS PGM button GUN PGM 116 Day Station COS Station COS Dial 116 Enter the appropriate Station Range Flex Btn Select the desired Flexible button from the chart below Enter the appropriate value Press the Hold Save button Description Each station is assigned a Class Of Service COS that determines the station dialing restriction for Day operation refer to Station COS Table Each station is assigned a Class Of Service COS that determines the station dialing restriction for Night operation refer to Station COS Table Default Values Station COS Restrictions Station COS Table No restrictions are placed at the station for dialing The assignments in the Exception Table A are monitored for Allow and Deny numbers The assignments in the Exception Table B are monitored for Allow and Deny numbers 39 The assignments in both Exception Tables A amp B are monitored for Allow and Deny numbers Issue 2 0 July 2010 Station COS Restrictions 5 The leading digit dialed cannot a long distance code The dialed digits be longer than 7 digits In addition the Canned Toll
30. 0 July 2010 3 5 11 Modem Assignment PGM 170 170 defines the station or CO line associated with the modem on the optional MODU If the station or CO line associated with the modem receives a call the modem is connected Procedure Press the TRANS PGM button 1 Select the desired Flexible button Enter the appropriate value Press the Hold Save button 2 Dial 170 3 4 5 PGM Flex 170 Btn Station number 1 Description This parameter assigns an associated station for the Modem Default 147 Values Station number CO Line Number 2 This parameter assigns an associated CO line for the Modem Not assigned Analog CO line number 99 Issue 2 0 July 2010 3 5 12 Music Assignments PGM 171 PGM 171 assigns music and tone sources Procedure 1 Press the TRANS button 2 Dial 171 3 Select the desired Flexible button For SLT MOH assignments press Flexible button 1 5 for SLT MOH 1 5 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 171 Btn BGM Type 1 This parameter defines the source for BGM Back Ground Music 1 Internal Music O Not assigned see Flexible 1 Internal Music button 8 2 External Music 3 unused 4 8 SLT MOH 1 5 2 This parameter defines the source for Music On Hola 1 Internal Music 0 assigned see Flexible 1 Internal Musi
31. 0 July 2010 3 5 8 DID DISA Destination 167 PGM 167 establishes destinations for DID DISA calls that encounter busy error No answer or DND conditions and enables VMIB prompts for these conditions Procedure 1 Press the TRANS button 2 Dial 167 3 Select the desired Flexible button VMIB Prompt Use select the Flexible button for the prompt 4 Enter the appropriate value for Destinations press the appropriate Flexible button 5 Press the Hold Save button PGM Flex Description Default Values 167 Btn Busy Destination 1 This parameter defines the destination when a DID or DISA call encounters busy 1 Tone Flexible button and no forwarding destination is enabled The destination can be busy Tone an 1 Tone Attendant or a Station Hunt Group When selecting Hunt Group enter the Hunt 2 Attendant Group number 3 Hunt Group enter group number Error Destination 2 This parameter defines the destination when a DID or DISA call encounters an error 1 Tone Flexible button The destination can be busy Tone an Attendant or a Station Hunt Group When 1 Tone selecting Hunt Group enter the Hunt Group number 2 Attendant 3 Hunt Group enter group number No Answer 3 This parameter defines the destination when a DID or DISA call encounters No 1 Tone Flexible button Destination answer and no forwarding destination is enabled The destination can be busy 1 Tone 9
32. 01 99 days E mail 5 The system can notify the user e mail address when a new voice message is 0 Disable 0 Disable Notification received The user e mail address must be defined in PGM 127 and PGM 129 1 Enable Future Delivery 6 The mailbox user may delay delivery of a voice message to another user in the 0 Disable 0 Disable Messages ip 60 1 Enable Confirm Message 7 The user may request delivery confirmation for a voice message sent to another user 0 Disable 0 Disable 174 Issue 2 0 July 2010 PGM Flex Description Default Values 238 Btn Receipt of the ip 60 The system will confirm delivery once the receiver listens to the 1 Enable message Private Message 8 A user may mark a message to another ip 60 user as a private message The 0 Disable 0 Disable Mark receiver cannot forward the message 1 Enable 175 Issue 2 0 July 2010 3 9 15 Hot Desk Attributes 250 250 defines attributes for Hot Desk agents including no of Agents and Automatic Logout timer Procedure 1 Press the TRANS button enc ves enc Qul PGM 250 Number of Agents Dial 250 Select the desired Flexible button Flex Btn 1 Enter or view the appropriate value Press the Hold Save button Description The number of Agents using the Hot desk feature determines the Agent numbers Agent numbers are assigned backwards from the highest station number
33. 1 dece 29 Press the TRANS PGM button Dial 105 The system displays the first 4 station ports on the first line of the LCD and the station number below the port Use the Volume buttons to display the station port to be assigned Select the desired Flexible button 1 4 for the port to be assigned Enter the appropriate value Press the Hold Save button Station Range assignment Procedure 1 Q d cda INI Press the TRANS PGM button Dial 105 The system displays the first 4 station ports on the first line of the LCD and the station number below the port Use the Volume buttons to display the first station port to be assigned Enter the new station range 2 to 4 digits for the start and ending station numbers The range may extend past the displayed ports and the system will assign the range to the ports consecutively until the entered range is exhausted Press the Hold Save button 12 Issue 2 0 July 2010 PGM Flex Description Default Values 105 Btn Station This parameter assigns station numbers for the system Station numbers can be 100 147 Non conflicting 2 to 4 Numbering Plan assigned individually or using the range method digits 0 9 13 Issue 2 0 July 2010 3 1 6 Flexible Numbering Plan A 106 PGM 106 is one of three 3 PGMs that assign dial codes for access to features and functions of the ip 60 60 Also see PGMs 107 and 109
34. 1 Alarm Reset 565 565 565 565 695 565 35 565 2 Group Call Pickup 566 566 1 566 36 666 3 UCD Group DND 568 568 568 568 698 2568 68 568 4 Night Answer 569 569 5712 699 569 69 69 5 Call Park Location Range 601 601 601 601 601 601 601 601 610 610 610 610 610 610 610 610 6 Direct Call Pick Up 7 i 7 2 7 Ne 7 nom 801 801 801 401 801 801 801 801 824 824 824 424 824 824 824 824 8 Access Individual CO Line 88 88 88 48 88 88 88 88 co lo Reserved 10 Access Held Line Group 8 8 8 4 8 8 8 8 11 Access Held Individual CO Line 8 8 8 4 8 8 8 8 co co co 12 Access to CO Line in the 1 Available CO Line 9 9 9 1 0 9219 o 228 Issue 2 0 July 2010 PGM Flexible Item Plan1 Plan2 Plan3 Plan4 Plan 5 Plan6 Plan Plan 8 Group 13 Attendant 0 0 0 0 9 0 0 9 14 Door Open 1 1 1 1 1 1 1 1 1 15 Door Open 2 2 2 2 2 2 2 2 2 16 Door Open 3 leo as ws 3 17 Door Open 4 4 4 laa 194 18 VM MSG Wait Ena
35. 119 PGM121 PGM122 PGM124 amp PGM179 CO Line 3 Initializes PGM140 PGM144 Database System Feature 4 Initializes PGM160 177 PGM108 Database Station Group 5 Initializes PGM190 amp PGM191 Database ISDN Tables 6 Initializes PGM201 PGM202 amp PGM231 Database Reserved 7 216 Issue 2 0 July 2010 PGM Flex Description Default Values 450 Btn System Timer 8 Initializes PGM180 PGM182 Database Toll Table 9 Initializes PGM224 amp PGM225 Database LCR Database 10 Initializes PGM220 PGM222 Tables 11 Initializes PGM227 PGM229 amp PGM232 PGM234 Flexible Button 12 Initializes PGM115 Program Networking 13 Initializes 320 324 Database All Database 14 Initializes all of the database System Reset By 15 Resets the ip 60 system Software DID Reroute 16 Reroute Destination assigned in PGM 231 Table Board Data 17 Initializes PGM 340 341 amp 155 Enblock Prefix 18 Initializes 205 Table 217 3 16 Print Prot Database PGM 451 PGM 451 outputs the database values for the various program sections Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 451 3 Select the desired Flexible button 4 For CO and Station programs enter the range to output 5 Press the Hold Save button to output data PGM Flex Description Default Val
36. 147 3 Enter the appropriate CO Line Range 4 Press the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 147 Btn CID Mode Select 1 This parameter defines the type of Caller Id signal provided by the PSTN 1 FSK 0 Disable 1 FSK 2 DTMF 3 Russia CID CID Name 2 When the analog CO line provides the caller s name as well as number the system 0 Telephone 0 7 Tel number Display can display the telephone number or the name and the telephone number received number 1 Name Detect 3 This parameter determines the types of call that include CID only local calls or all 0 Local 0 Local calls Intended for use in Russia only 1 AIl RCID Request 4 This parameter determines if the system will request Caller ID from the network 1 Auto 0 Auto Intended for use in Russia only 1 User Request 5 When RCID Request Flexible button 4 is set to auto the system will delay sending 150 1 5 010 150 in 10 milli Timer the request for the setting of this timer Intended for use in Russia only seconds second increments 75 Issue 2 0 July 2010 PGM Flex Description Default Values 147 Btn Virtual 6 When RCID Request Flexible button 4 is set to Auto the system automatically 020 20 seconds 001 300 in 1 Answer Timer answers incoming calls and routes them the appropriate Station
37. 184 defines the Chime Bell station pairs and the Chime Bell signal characteristics Procedure 1 Press the TRANS button 2 Dial 184 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 184 Btn Chime Bell 1 This parameter defines the Chime Bell pair 01 14 the first station activates the Not assigned 01 14 station pair Station Pair Chime Bell and the second station receives the Chime Bell signal Chime Bell Relay 2 This parameter assigns a Chime Bell pair 01 14 to activate an External Control Not assigned 01 14 External Relay as a Loud Bell contact Control Relay 0 2 Bell Timer 3 This parameter determines the duration of the Chime Bell signal at the receiving 02 seconds 01 20 in 1 second station The same timer is used for all 14 Chime Bell pairs increments Bell Frequency 4 This parameter defines two frequency components that make up the Chime Bell 1 0770 T1 4 digits in Hz signal The same Chime Bell frequencies are used for all 14 Chime Bell pairs Use T2 0000 T2 4 digits in Hz Flexible button 1 for T1 and Flexible button 2 to set T2 125 Issue 2 0 July 2010 3 6 DCOB ATTRIBUTE PGM 186 PGM 187 3 6 1 DCOB Attributes 186 PGM 186 is one of several programs that define attributes of digital E1R2 lines also see PGM 187 Procedure 1 Press the TRAN
38. 2 0 July 2010 Not supported for T1 E1 CO line 3 Hunt Group enter PGM Flex Description Default Values 167 Btn Destination answer forward or CCR to a busy destination 1 Tone Not supported for T1 E1 CO line 2 Attendant 3 Hunt Group enter group number Reroute Error 7 This parameter defines the destination when a DID or DISA call is rerouted with No 2 Attendant Flexible button Destination answer forward or CCR to an invalid destination 1 Tone Not supported for T1 E1 CO line 2 Attendant 3 Hunt Group enter group number Reroute No 8 This parameter defines the destination when a DID or DISA call is rerouted with No 2 Attendant Flexible button Answer answer forward or CCR and is not answered in the DID DISA No answer time PGM 1 Tone Destination 181 Flexible button 2 2 Attendant 95 group number Issue 2 0 July 2010 3 5 9 External Control Contacts 168 PGM 168 configures the four External Control Contacts Procedure 1 Press the TRANS button Dial 168 Select the desired Flexible button Enter the appropriate value Press the Hold Save button enc ves nc Qul PGM Flex Description Default Values 168 Btn First Contact These parameters define the function of each of the four Control Contacts in the ip Not assigned 1 station number 60 60 Contacts 1 and 2 are located in the Basic cabinet and contacts 3 and 4 are LBC located in the Exp
39. 33 Registration Mobile Extension 34 Active Mobile Extension 35 Register Mobile Extension CLI 36 Active Mobile Hunt 37 Msg Wait Notice To Mobile Extension 41 Wake up Time Registration One time Continuous 42 Wake up Time Cancel 43 Activate Conference Room 44 Deactivate Conference Room 451 Call Coverage Mode 452 Call Coverage Delay Ring Cycle 51 Pre selected MSG Activation 2 Set Custom Message 61 Record VMIB User Greeting 6 Play Time amp Date 63 Play Station Number 64 Play Station Status 65 Record VMIB Page Message 66 Erase VMIB User Greeting 67 Erase VMIB Page Message Outbound Notification Menu 1 Activate 68 2 0 9 Retry Count 3 0 9 minutes Interval 69 Outbound Notify Number 60 E mail Notification 6 Record User Name 231 Issue 2 0 July 2010 Issue 2 0 July 2010 Code ITEM REMARK 6 Erase User Name 71 LCD Display Mode English Domestic Language Keyset 72 MPB Version Display Keyset 73 Background Music Keyset 74 Station User Name Registration 75 Headset Speakerphone Mode Keyset 76 Headset Ring Mode Keyset 77 WTU Station Number Receive Keyset Not supported in ip 60 60 78 Serial No SW Packages Keyset with LCD 79 PC Phone Lock Key oe Hot desk Logout 0 Hot desk Login 1 Relocation Out 2 Relocation IN 9 Registe
40. CLI on an incoming DID CO Not assigned Up to 20 digits Number line call routes the call to the destination specified under Flexible button 2 Conversion Table 2 This parameter defines the Flexible DID Conversion Table index PGM231 for the Not assigned 000 999 Flexible Index destination for a call when the CLI an incoming DID call matches the CLI defined DID Conversion under Flexible button 1 Table index 173 3 9 14 Voice Mailbox COS Table 238 PGM 2368 assigns characteristics to each Class of Service for Voice Mailboxes The COS defines characteristics for Voice mails as well as enables certain features for mailboxes assigned the COS There are five 5 Classes of Service Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 238 3 Dial the COS number 1 5 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 238 Btn Greeting Length 1 The system can limit the length of the User Greeting for the mailbox 15 seconds 00 99 seconds Message Record 2 The system limits the maximum duration of a recorded voice message to the 300 seconds 001 600 seconds time mailbox Number of 3 The system limits the number of messages stored in a mailbox 050 001 250 Messages Retention Time 4 The system limits the duration a message will be stored in the mailbox 15 days
41. Description Default Values 292 Btn SMS Receive 1 This parameter assigns the range of stations to receive SMS messages on the CO 0 Off Station Range station lines in the range 0 Off 1 Display SMS 2 This Flexible button displays the stations allowed to receive external SMS Receive station messages SMS Outgoing 3 When enabled On CO lines in the range are used to submit external SMS 0 Off 0 Off messages to the SMS Center 1 Non CID SMS 4 When enabled On the system will automatically identify incoming SMS calls without 0 Off 0 Off Korea Only using CLI from the SMS Center special tone detection is used Intended for Korea 1 only 178 Issue 2 0 July 2010 3 11 Private Networking PGM 320 324 3 11 1 Networking Basic Attributes 320 PGM 320 enables Networking and defines basic attributes for network signaling and CAS Procedure 1 Press the TRANS button 2 Dial 320 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 320 Btn Networking 1 This parameter enables the Private Network feature The Networking lock key must O Off 0 Off Enable be installed 1 Networking Retry 2 This parameter defines the number of times the system will attempt a network 00 00 99 Count connection to a PSTN line This parameter does not affect a
42. Flexible button 17 After the increments timer expires the call is routed with ring to assigned stations FAX CO Call 14 This parameter sets the time interval allowed for the FAX station port 8 station 1 minute 1 5 1 minute Timer port to answer a FAX call After expiration of the timer the call is disconnected increments 123 Issue 2 0 July 2010 3 5 22 Indication 183 PGM 183 defines the Supervisor for In Room groups and members that receive the In Room indication Procedure 1 Press the TRANS button 2 Dial 183 3 Enter the In Room Table index 01 10 4 Select the desired Flexible button For Member assignment press Flexible button 2 then select a Flexible button 1 4 for up to four 4 members ge Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 183 Btn In Room Group 1 This parameter defines the In Room group 01 to 10 Supervisor station that will Not assigned Station number of Supervisor control the In Room indication for the group Supervisor In Room Group 2 This parameter assigns members to an In Room Group maximum 4 members The Not assigned Flexible button 1 4 Member members In Room button illuminates when the Supervisor activates the In Room Station number indicator by pressing the Supervisor s In Room button 124 Issue 2 0 July 2010 3 5 23 Chime Bell Attributes 184 PGM
43. Internal Page 06 01 10 07 External 07 1 08 All Call Page 08 1 Internal Call Page 08 2 All Call Page 09 Net Number 09 Net Number 10 Conference Room 10 1 9 166 Destination Values 11 Station Voice Mailbox 4117 station number 12 Virtual Voice Mailbox Dial Pad Character Chart 0 Blank x1 2 167 12 Virtual mailbox number Issue 2 0 July 2010 Issue 2 0 July 2010 3 9 9 System Speed Zone PGM 232 PGM 232 configures the parameters for the System Speed Zone groups Procedure 1 Press the TRANS button 2 Dial 232 3 Enter a Zone number 01 10 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 232 Btn Speed Bin Range 1 This parameter assigns System Speed Dial bins to a Speed Zone Only Speed Dial Zone 1 2200 Range between in Zone bins 2200 to 2499 can be assigned to a zone Speed bins 2000 2199 cannot be 2499 2200 2499 assigned to a System Speed Zone Zones 2 10 not assigned Station Range to 2 This parameter assigns stations allowed access to Speed Dial bins in the zone Zone 1 All Flexible button 1 4 Access Zone Select the Flexible button associated with a station or enter a station range stations allowed or a station range access Toll Checking 3 This parameter determines if the syst
44. LAN port ip 60 Server IP 2 This parameter defines the IP address for the system s LAN port This address is 192 168 1 1 IPv4 address address assigned to allow LAN access to the system database and maintenance functions CLI IP address 3 not used Gateway Address 4 This parameter defines the IP address of the gateway serving the system LAN port 0 0 0 0 IPv4 address Subnet Mask 5 This parameter defines the Subnet mask for the system LAN interface 255 255 255 0 IPv4 Subnet mask Point to Point 6 This parameter enables use of Point to Point protocol with the optional Modem unit 0 Off 0 Off Protocol or an ISDN PRI Line 1 Dial Pad Character 18 Issue 2 0 July 2010 0 0 00 Blank 1 v 2 3 19 3 1 9 Flexible Numbering Plan 109 Issue 2 0 July 2010 PGM 109 is one of three 3 PGMs that assign dial codes for access to features and functions of the ip 60 60 Also see PGMs 106 and 107 Procedure 1 Press the TRANS PGM button Extension Control 2 Dial 109 3 Select the desired Flexible button from the chart below 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 109 Btn Reserved 1 Reserved 2 Reserved 3 Conference 4 57 Non conflicting 2 to 4 Room digits 0 9 and SLT Conference 5 58 Page Join Extend 6 THE Unsupervised Conference Remote Mobile
45. LG ERICSSON 2 Aria 1 60 Admin Programming Manual Issue 2 0 July 2010 Revision History Issue Date Description 1 0 2006 10 Preliminary release for ip 60 60 2007 12 Add version 3 8 features for ip 60 60 1 2 2008 03 Update features related to PRHB8 2 0 2010 07 Update and reformat through out Added T1 Added Enhanced Voice Services Copyright 2010 LG Ericsson Co Ltd All Rights Reserved This material is copyrighted by LG Ericsson Co Ltd Any unauthorized reproductions use or disclosure of this material or any part thereof is strictly prohibited and is a violation of Copyright Laws LG Ericsson reserves the right to make changes in specifications at any time without notice The information furnished by LG Ericsson in this material is believed to be accurate and reliable but is not warranted to be true in all cases LG Ericsson and ip 60 are trademarks of LG Ericsson Co Ltd All other brand and product names are trademarks or registered trademarks of their respective companies Issue 2 0 July 2010 Table of Contents 1 2 2 22222 eio ree ennenen nennen 1 1 4 Section 4 40 00 4 4 04222 1 POUCH ON Leib freuen voe th Pen itae etie to emer atu 1 1 1 2 Admin Programming Overview nennen nennen nnne 1 1 1 3 Admin Programming Procedures
46. Minimum 3 This parameter defines the minimum duration of a Flash new dial tone request for 020 200 milli 000 250 in 10 milli Hook Flash Timer the ip 60 to register the Flash signal otherwise the signal is consider a spurious seconds second increments signal SLT Ring Phase 4 This parameter defines the overall duration of ring signal sent to an SLT port The 5 seconds 2 5in 1 second Timer Ring on period is fixed at 1 second The remaining time is the Ring off period The increments default is 1 second Ring on and 4 seconds Ring off for a total duration of 5 seconds Station Auto 5 This parameter sets the length of time a station receives intercom Ring Back tone 060 seconds 020 300 in 1 Release Timer before the call attempt is abandoned and error tone provided to the station Also the second increments 122 Issue 2 0 July 2010 PGM Flex Description Default Values 182 Btn station will receive Park recall for the Auto Release Timer Unsupervised 6 This parameter sets the timer that controls the duration of an Unsupervised 10 minutes 0 99 in 1 second Conference Timer Conference or other CO line to CO line connections increments Wake up Fail Ring 7 This parameter defines the duration of ring the System Attendant receives when a 20 seconds 00 to 99 in 1 seconds Timer user fails to respond to a Wake up ring A setting of 00 disables the Wake up Fail increments At
47. PABX CO Supply PABX CO 10 PABX CO Yes ip 60 60 Busy Tone PABX CO Supply PABX CO 11 No PABX CO Yes ip 60 60 Announce Tone PABX CO CO Flash Timer 12 This parameter defines the length of a Flash on the PABX CO line The Flash type 050 500 msec 000 300 in 10 milli is defined in PGM 141 Flexible button 7 second increments 65 Issue 2 0 July 2010 PGM Flex Description Default Values 142 Btn Open Loop 13 Common analog CO lines use a short Open Loop signal as disconnect This 03 300 milli 00 20 in 100 milli Detect Timer parameter defines the minimum duration of the expected Open Loop disconnect seconds second increments signal Line Length 14 In certain regions SAF the CO line length to a system may vary greatly In this 0 Short 0 Short case the length can be assigned as Short or Long for each CO line 1 Long DISA Answer 15 When a call is received on a CO line with DISA service the system will answer the 2 2 seconds 1 9in 1 second Timer call when the DISA Answer Timer expires increments DISA Delay 16 Once answered the system attaches a DTMF receiver to the DISA call to receive 1 1 second 1 9in 1 second Timer caller dialed digits This timer introduces a delay before attaching the DTMF increments receiver to the CO line SMDR Print 17 When enabled On calls on the CO line s will be included in the SMDR outputs 1 Yes 0
48. SIP signaling messages Transport UDP UDP 193 Issue 2 0 July 2010 PGM Flex Description Default Values 500 Btn Control Protocol or User Datagram Protocol UDP TCP 100Rel Support When enabled the system will acknowledge provisional response 1xx On Off messages from the call server On Use R port When enabled the system will support the R port SIP Method for NAT On Off Method traversal On Use Single Code When enabled the system will employ only the codec specified in PGM 340 Flexible Off Off Only button 6 If unavailable at the remote end the call is dropped On Remote Part ID When enabled On the system supports the Remote Party Header in SIP Off Off messages On 181 Message When enabled On the 181 forwarding message is supported On Off On IP Centrex When enabled the system will support IP Centrex services from a Broadworks Off Off platform On Dial Pad Character Chart 1 10 3 30 D 31 Q 11 32 2 12 33 4 40 5 50 6 60 G 41 J 51 M 61 H 42 K 52 N 62 1 43 L 53 O 63 194 Issue 2 0 July 2010 P 71 R 73 S 74 x 0 oo Blank 1 2 3 195 Issue 2 0 July 2010 3 12 4 SIP Attributes 501 PC Admin only 501 is one of two PGMs used to configure SIP operation see also 500 Procedure 1 PC Admin only PGM to reg
49. SLIB Intended for SAF only 32 00 63 3 Long ACD Far SLIB Intended for SAF only 32 00 63 4 Long ACO DTIB Intended for SAF only 32 00 63 PGM Flex Description Default Values 417 MBU DSP Btn Rx Gain 1 24 00 63 2 DCO SMS 38 00 63 3 SLT SMS 17 00 63 4 ACO DTMF CID DTIB 38 00 63 5 ACO FSK CID 38 00 63 213 Issue 2 0 July 2010 PGM Flex Description Default Values 418 MBU DSP Tx Btn Gain 1 ACO SMS 32 00 63 2 SMS 38 00 63 3 SLT SMS 32 00 63 4 SLT FSK CID 32 00 63 PGM Flex Description Default Values 420 System Tone Btn Frequency Dial 1 Dial Tone 0350 0440 Two 4 digit numbers Dial 2 Ring Back Tone 0440 0480 Two 4 digit numbers Dial 3 Busy Tone 0480 0620 Two 4 digit numbers Dial 4 Error Tone 0480 0620 Two 4 digit numbers Dial 5 Dummy Dial Tone 0350 0440 Two 4 digit numbers PGM Flex Description Default Values 421 Differential Btn Ring Frequency Dial 1 Ring 1 1000 1020 Two 4 digit numbers Dial2 Ring 2 0890 0910 Two 4 digit numbers Dial 3 Ring 3 1260 1280 Two 4 digit numbers Dial 4 Ring 4 0800 0820 Two 4 digit numbers 214 Issue 2 0 July 2010 PGM Flex Description Default Values 422 Distinctive Btn Ring Frequency Dial1 Ring 1 0480 0000 Two 4 digit numbers Dial2 Ring2 0400 0000 Two 4 digit numbers Dial 3 Ring 3 0620 0000 Tw
50. Turkish 15 2 This selection followed by Flexible button 2 outputs displays for a normal DECT phone display or Large DKT display 0 Normal 1 LG GAP 2 Large End Print This selection terminates the print output 219 Issue 2 0 July 2010 3 17 Initialize Database by MPB Version PGM 452 452 permits initialization of the system database based on the software version Procedure Press the TRANS PGM button 1 Select the desired Flexible button Press the Hold Save button to initialize 2 Dial 452 3 4 PGM Flex 452 Btn Ver 3 7 1 Ver 3 8 2 Description When upgrading a system to a 3 7 or 3 8 version system software new database parameters must be set to the default values The entire database may be set to default or using this program only the new parameters are set to default Flexible button 1 is used when upgrading to version 3 7 and Flexible button 2 is used when upgrading to version 3 8 220 Default Values 4 1 Admin Program Code Index Issue 2 0 July 2010 4 ADMIN REFERENCE CHARTS Admin Program Index Chart Main Menu PRE PROGRAMMED BASE PGM Item 100 Location Program 101 Board Assignment 103 Logical Slot Assignment 104 Numbering Plan Type 105 Flexible Number Plan Station Number 106 Flexible Number Plan A 107 Flexible Number Plan B 108 Setting 109 Flexible Number P
51. call will remain parked before recalling the station 120 seconds 00 600 in 1 second Timer that parked the call increments Camp On Recall 3 This parameter sets the duration a transferred call will remain camped on to a station 030 seconds 000 200 in 1 Timer before recalling the transferring station second increments Exclusive Hold 4 This parameter sets the duration a call will remain on Exclusive hold before recalling 060 seconds 000 300 in 1 Recall Timer the station that placed the call on hold second increments I Hold Recall 5 This parameter sets the duration the station will receive recall before the Attendant 030 seconds 000 300 in 1 Timer will also receive the recall second increments Sys Hold Recall 6 This parameter sets the duration a call will remain on System hold before recalling 030 seconds 000 300 in 1 Timer the station that placed the call on hold second increments 116 Issue 2 0 July 2010 PGM Flex Description Default Values 180 Btn Transfer Recall 7 This parameter sets the duration transferred calls ring the intended receiver before 030 seconds 000 300 in 1 Timer recalling the transferring station second increments ACNR Delay 8 When no CO line is available for an ACNR attempt this parameter sets the delay 030 seconds 000 300 in 1 Timer before ACNR reattempts access to a CO line This will not affect the retry counter second increments ACNR No 9 This
52. direct connection between two networked systems Networking 3 When enabled On the system displays the name of the calling station in the LCD 1 On 0 Off Enable of the called station 1 Networking 4 When enabled On the system displays the name of the answering station in the 0 Off 0 Off CONP Enable LCD of the calling station 1 Networking 5 This parameter determines the message information element type used for 1 Facility 0 User to User Signal Method supplementary network service messages The system employs either the Facility 1 Facility 179 Issue 2 0 July 2010 PGM Flex Description Default Values 320 Btn or the User to User Information element as assigned here Networking CAS 6 This parameter enables Centralized Attendant Service for the system CAS should 0 Off 0 Off Enable not be enabled at the system where the CAS Attendant is located 1 Networking VPN 7 Reserved 0 Off 0 Off Enable 1 Networking 8 When enabled On the system employs the Call Completion Retain mode for 0 Off 0 Off Retain Mode supplementary services 1 180 Issue 2 0 July 2010 3 11 2 Networking Supplementary Attributes 321 PGM 321 configures signaling for supplementary features and characteristics of the BLF Manager Procedure 1 Press the TRANS button 2 Dial 321 3 Select the desir
53. for Lunch mode service when Auto Ring Not assigned 4 digits 0000 23 59 service is active Lunch End 5 This parameter defines the end time for Lunch mode service when Auto Ring service Not assigned 4 digits 0000 23 59 is active 169 Issue 2 0 July 2010 3 9 11 Voice Mail Dialing Table PGM 234 PGM 234 defines the DTMF digits sent to an external VM to process a call Procedure 1 Press the TRANS button 2 Dial 234 3 Dial digit 1 9 for the VM Table index 4 Dial 1 for Prefix insertion or dial 2 for Suffix insertion 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 234 Btn Put Mail This parameter defines the code sent to the external VM to receive an incoming Prefix P 12 digits 0 9 Index 1 Voice message Suffix and DND for Pause Get Mail This parameter defines the code sent to the external VM to review Voice message Prefix P 12 digits 0 9 EP Index 2 Suffix and DND for Pause Busy This parameter defines the code sent to the external VM to receive an incoming Prefix P 3P 12 digits 0 9 Index 3 Voice message when the call encounters busy Suffix and DND for Pause No Answer This parameter defines the code sent to the external VM to receive an incoming Prefix P 4P 12 digits 0 9 Index 4 Voice message when the call is not answered Suffix and DND
54. for an incoming call seconds second increments Dial Tone Delay 8 not used Timer Line Status 9 This parameter defines the code the system will send to indicate idle line status in 6 1 9 accordance with E1R2 specifications Calling Category 10 This parameter defines the code sent in response to a call category request from the 1 1 9 network in accordance with E1R2 specifications ANI Request 11 When enabled in accordance with 1 2 specifications the system will request 0 Off 0 Off ANI Automatic Number Identification from the network as the CLI for the call 1 Digit Num 12 not used R2 OUT DIGIT 13 This parameter sets the Inter digit time for R signaling on a digital CO line 05 seconds 01 50 in 1 second TIMER increments R2 ERROR 14 When enabled On the system will play the VMIB error announcement when an 0 Off 0 Off PROMT USAGE error occurs on an R2 outgoing call If no VMIB announcement is available the 1 system sends error tone R2 BUSY 15 When enabled On the system will play the VMIB busy announcement when a busy 0 Off 0 Off PROMT USAGE condition occurs on an R2 outgoing call If no VMIB announcement is available the 1 system sends busy tone R2 ANNOUNCE 16 When enabled On and the R2 line returns an ANNOUNCE message indicating the O Off 0 Off PROMT USAGE destination number is invalid etc the VMIB error announcement is played If no 1 VMIB anno
55. in one of six modes Modes provide for activation when the user Dials while receiving internal dial tone Internal Accesses a CO line with a CO line Group button or by dialing a CO line Group access code Direct or Accesses a CO line with a Loop button or by dialing 9 Values 00 LCR disabled 01 Dial 9 02 7 Internal amp Loop 11 Loop amp Direct 12 All with Loop access immediately 13 All with Loop access delay Day Zones 2 This parameter divides the days of week into one of three groups Day Zones for All days groups separate LCR treatment Each day Monday through Sunday represented 1 Day Zone 1 LCR Access 1 This parameter defines the user action that will access LCR The user activates 00 respectively by Flexible button 1 7 is assigned to a zone Flexible button 1 7 1 3 day zone Time zones for 3 This parameter assigns three time zones for the day of week grouping 1 Day Zone Flexible button 1 3 148 Issue 2 0 July 2010 PGM Flex Description Default Values 220 Btn Day Zone 1 1 Separate LCR treatments are assigned for each time zone under PGM 221 and 2 digt pair 00 24 223 Time is assigned in 24 hour format with 00 amp 24 as midnight Any hour not covered by the time zones entered is treated as part of time zone 1 Time zones for 4 This parameter assigns three time zones for the day of week grouping 2 Day Zone Flexible button 1 3 Day Zone
56. line is available for access by another user This interval second increments allows time for the CO to return the circuit to an idle state Dial tone Delay 3 This parameter sets the time between the user accessing a T1 CO line and dial tone 10 1 second 02 50 in 100 milli Timer delivery to the user This interval allows the T1 CO line to setup the circuit If Dial second increments Tone Detect PGM 160 Flexible button 6 is enabled when dial tone is detected it is immediately sent to the user otherwise this timer is employed Inter digit Timer 4 not used Wink Timer 5 This parameter sets the duration of the Wink signal for Wink start T1 CO lines 10 200 milli 07 15 in 20 milli parameter is also used to define the delay when delay start is assigned for the T1 seconds second increments CO line 77 Issue 2 0 July 2010 PGM Flex Description Default Values 152 Btn Out pulse Rate 6 not used Seize Timer 7 This parameter defines the duration of the seizure signal provided by the T1 CO line 3 60 milli 000 127 in 20 milli for DID and TIE lines seconds second increments Release Timer 8 This parameter defines the duration of the release signal provided by the T1 CO line 7 140 milli 000 127 in 20 milli for DID and TIE lines seconds second increments IASG Mode 9 not used 1 DTMF 0 Pulse 1 DTMF Ring Detect Time 10 This parameter d
57. rerouted 25 seconds 00 99 in 1 second Answer Timer to the DID DISA No answer destination PGM 167 Flexible button 3 increments VMIB User 3 This parameter determines the maximum duration of the user recorded greeting for 020 seconds 010 255 1 Record Timer the VMIB Voice Mail Longer greetings cannot be stored second increments VMIB Valid User 4 This parameter establishes the minimum duration the ip 60 will recognize as a 4 seconds 0 9in 1 second Message Timer legitimate Voice Mail shorter messages are discarded If set to 0 a message increments cannot be recorded in the VMIB Door Open Time 5 This parameter sets the duration the Door Open contact will remain activated when 20 2 seconds 05 99 in 100 milli station dials the Door Open code second increments ICM Box Timer 6 This parameter sets the duration a station receives Door Phone ring when the Door 30 seconds 00 60 in 1 second Phone Call button is pressed increments 119 Issue 2 0 July 2010 PGM Flex Description Default Values 181 Btn ICM Dial Tone 7 This parameter sets the duration Intercom dial tone is provided to the user When 10 seconds 01 20 In 1 second Timer the timer expires the call is abandoned and the system returns error tone increments Inter digit Timer 8 This parameter sets the duration the system permits the user between dialed digits 05 seconds 01 20 in 1 second on an internal cal
58. sse 141 3 8 2 COLP CLIP Table PGM 201 si 143 3 8 3 MSN Table PGM 202 Gerh Ca cut rao ov eaa emere 144 3 9 Tables 204 205 and 220 238 amp 250 145 3 9 1 Local Code Table 204 0 145 3 9 2 Enblock Prefix Table PGM 205 146 3 923 LCER PGOGM 2207223 148 3 9 9 4 LCR Attrib tes POM 220 dete eoim AE 148 Issue 2 0 July 2010 3 9 3 2 Leading Digit Table POM 22 150 3 9 3 3 LCR Digit Modification Table PGM 222 sse 152 3 9 3 4 LCR Table Initialization PGM 223 154 39 4 Toll Fable PGM 224 226 siren ene Cc be b e po EE 156 3 9 4 1 Toll Exception Tables 224 nennen nnne 156 3 9 4 2 Canned Toll Tables 225 158 3 9 4 3 Emergency Service Call PGM 229 ate aida eta tuta 159 3 9 5 Authorization Code Table 227 160 3 9 6 Customer Call Routing PGM 2298 161 3 9 7 Executive Secretary Table 229 2 22 44224 164 3 9 8 Flexible DID Conversion Table 231 165 3 9 9 System Spe
59. station Individual Flexible button functions can be 03 DSS MAP 2 defined in PGM 115 04 DSS MAP 3 Company 3 This parameter assigns the first name of the user associated with the station for use Not Assigned 12 Characters Directory First with the Company Directory Use two digits for each character as shown in the Dial Name Pad Character Chart below Company 4 This parameter assigns the last name of the user associated with the station foruse Not Assigned 12 Characters Name Pad Character Chart below Flexible Button Configurations for DSS DLS Map Map Button Configuration 1 Buttons 1 to 12 Button 1 Intrusion Button 2 All Call Page Button 3 Call Park 01 Button 4 Station Group 1 5 Button 6 Internal All Call Page Button 7 Call Park 02 Button 8 Station Group 2 Button 9 Group Call Pickup Button 10 External All Call Page Button 11 Call Park 03 Button 12 Station Group 3 Buttons 13 to 48 Station Ports 100 135 2 Station Ports 136 147 3 Blank 22 Dial Pad Character Map 0 Blank 1 U x2 23 Issue 2 0 July 2010 3 2 2 Station Attributes 111 PGM 111 is one of four 4 program groups that assign general attributes to the station range Also see PGMs 112 113 and 114 Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial 111 3 Enter the appropriate Sta
60. station Not assigned 1 Station Destination in the group has been tried The call remains at the last station in the group or 2 Hunt routes to the overflow destination after the Overflow timer Flexible button 8 expires 3 VMIB 00 70 00 disable 4 System Speed ft 2000 2499 Overflow Timer 8 This parameter sets the interval a call will queue to a group before routing to the 180 seconds 000 600 in 1 Overflow destination Flexible button 7 second increments Wrap up Timer 9 This parameter sets the duration a station remains unavailable after completing a 002 seconds 000 999 in 1 call second increments Music Source 10 This parameter determines if a queued caller receives Ringback tone or MOH 0 0 Not assigned by this field 1 Internal Music 2 External Music 3 Not in ip 60 60 4 8 SLT MOH 9 Hold tone Max Queued 11 This parameter determines the maximum number of calls that can queue to the 99 00 99 Call Count Group When the queued calls exceed the Maximum Queued Call Count additional calls are ignored 137 191 Issue 2 0 July 2010 Flex Description Default Values Ring Btn VMIB Supervisor 12 Not used Hunt Member 13 When enabled On a member with Call Forward active will not receive Hunt Group 1 On 0 Off forward calls the member is considered unavailable for group calls 1 Queue Count 14 When enabled On the LCD of
61. station is allowed access to the System paging facilities to 0 Off 0 Off send page announcements 1 Ring 9 This parameter defines the ring tone the station will receive for incoming calls 1 Ring Type 1 1 Ring Type 1 Ring type 1 1000 amp 1020 Hz 2 Ring Type 2 Ring type 2 890 amp 910 Hz 3 Ring Type 3 Ring type 3 1260 amp 1280 Hz 4 Ring 4 Ring type 4 800 amp 820 Hz Speaker Ring 10 This parameter determines which device will receive ring the speaker headset or 1 Speaker 1 Speaker S both 2 Headset H 3 Both B Speakerphone 11 When enabled the station speakerphone will be enabled and available for use 1 On 0 Off 1 VMIB Slot 12 This parameter identifies the slot of the VMIB for use by the station Not available N A Only one available the ip 60 60 has only one available VMIB slot Intercom 13 This parameter assigns the Intercom Tenancy Group for the station A 0 value is no 1 Grp 1 1 5 Tenancy Group group assignment Error Tone for Tel 14 When enabled On busy tone is sent to the SLT port in place of error tone This 0 Off 0 Off Answering allows a TAD to recognize disconnect supervision 1 Device SLT Flash Drop 15 This parameter determines the treatment of active calls when the user momentarily 0 Disable 0 Disable activates the hook switch Flash 0 Disabled the active call is placed on hold and t
62. the CO lines Each CO line is assigned 01 00 25 CO Group with other CO lines having similar characteristics Group 00 is for Private lines and Group 25 is for unused lines CO COS 2 This parameter defines the Class Of Service COS for CO lines The CO COS is 1 1 5 combined with Station COS PGM 116 to determine dialing restrictions for a call CO COS 1 Station COS applies CO COS 2 Exception Table A governs CO COS 3 Exception Table B governs CO COS 4 Restricts LD calls and Exception Table C CO COS 5 Overrides Station COS 2 6 with no restrictions DISA Account 3 When enabled On DISA callers attempting to place a CO line call must enter a 1 On 0 Off Code Station or System Authorization Code PGM 227 1 CO Line Assign 4 This parameter determines the Start and Disconnect signal for the CO line Loop 0 Loop 0 Loop 61 Issue 2 0 July 2010 PGM Flex Description Default Values 141 Btn or Polarity Reversal 1 Polarity Reversal CO Line Type 5 CO lines can be assigned for operation with a PBX or Centrex enforcing COS aftera 0 CO 0 PBX Centrex Trunk access code is dialed see PGM 172 1 PBX Centrex CO Line Signal 6 The system can send either DTMF or Open loop pulses as dial pad signals on 1 DTMF 0 Pulse analog CO lines 1 DTMF Analog CO Line 7 This parameter determines the type of Flash signal for analog CO lines Open
63. the CO lines in the group The Flexible access to all CO button toggles access to the CO Group and the LED indicates access Groups On allowed access Off access not allowed 41 Issue 2 0 July 2010 3 2 9 Internal Page Zone PGM 118 PGM 118 defines the Internal Page Zones that will transmit a page to the speaker of the station Procedure 1 Press the TRANS PGM button 2 Dial 118 3 Enter the appropriate Station Range 4 Pressthe Flexible button to enable disable Page Zone access 5 Press the Hold Save button PGM Flex Description 118 Btn Internal Page 1 5 Stations are assigned to receive pages from any combination of the five Internal Zone Page Zones The Flexible button toggles access to the Zone and the LED indicates Zone membership On Page Zone member will receive pages Off Not a Page zone member will not receive pages Default Zone 1 Values Flexible button 1 5 42 Issue 2 0 July 2010 3 2 10 Conference Page Zone Access 119 PGM 119 defines the Conference Page Zones that will transmit pages to the station Conference Page Zones are Internal Page Zones 6 through 10 Procedure 1 Press the TRANS PGM button 2 Dial 119 3 Enter the appropriate Station Range 4 Pressthe Flexible button to enable disable Conference Zone access 5 Press the Hold Save button PGM Flex Description 119 Btn Conference Page 1 5
64. to a group before routing to the 180 seconds 000 600 in 1 Overflow destination Flexible button 7 second increments Overflow 7 When assigned calls to a station in the group queue until answered or each station Not assigned 1 Station Destination in the group has been tried The call remains at the last station in the group or 2 Hunt routes to the overflow destination after the Overflow timer Flexible button 6 expires 3 VMIB 00 70 00 disable 4 System Speed 2000 2499 Group Name 8 This parameter assigns a name maximum 12 characters to the group Not assigned 12 Characters Assign 3 7 2 5 Pick up Group Attributes PGM 191 Flex Description Default Values Pick up Btn 1 When enabled On member stations can answer calls at other member stations by O Off 0 Off going off hook 1 All Ring 2 When enabled On all member stations ring when any member receives an 0 Off 0 Off intercom call Auto Pick up Flexible button 1 must be enabled 1 139 Issue 2 0 July 2010 3 7 2 6 Network VM Group Attributes PGM 191 Flex Description Default Values Network VM Btn Group Name 1 This parameter assigns a name maximum 12 characters to the group Not assigned 12 Characters Assign 140 Issue 2 0 July 2010 3 8 ISDN System Base Programs PGM 200 202 3 8 1 System ISDN Attributes PGM 200 PGM 200 def
65. value 5 Press the Hold Save button PGM Flex Description Default Values 173 Btn Transfer Call 1 This parameter defines the relative priority of PLA for transferred calls 1 Recall 2 This parameter defines the relative priority of PLA for recalls 2 ncoming Call 3 This parameter defines the relative priority of PLA for incoming calls 3 1 4 Queued Call 4 This parameter defines the relative priority of PLA for queued calls 4 104 Issue 2 0 July 2010 3 5 15 RS 232C Port Setting 174 PGM 174 defines the characteristics of the RS 232C and Modem MODU ports Procedure 1 Press the TRANS PGM button 2 Dial 174 3 Select the desired Flexible button Flexible button 1 COM1 RS 232C port Flexible button 2 COM2 Modem MODU port 4 Select desired parameter Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 174 Btn BAUDRATE 1 This parameter defines the Baud Rate of the selected COM port 6 0 N A 1 N A 2 1200 Baud 3 2400 Baud 4 4800 Baud 5 9600 Baud 6 19200 Baud 7 38400 Baud CTS RTS 2 This parameter enables CTS Clear to Send RTS Ready to Send protocol for the 0 Off 0 Off COM port 1 105 Issue 2 0 July 2010 PGM Flex Description Default Values 174 Btn Page Break 3 When enabled On the system will insert page break after prin
66. value 5 Press the Hold Save button PGM Flex Description Default Values 341 Btn GK Usage 1 When enabled the ip 60 will employ the GateKeeper to route all H 323 VoIP 0 Off 0 Off outgoing calls 1 0n GK Call Mode 2 This parameter determines the GateKeeper Call routing mode 0 Direct 0 Direct 1 Reroute Open H245 3 This parameter determines if the system will open an H 245 channel for H 323 VoIP O Off 0 Off calls 1 245 4 This parameter determines if the GateKeeper will employ tunneling for H 245 0 Off 0 Off Tunneling messages 1 Pre granted 5 When enabled On the GateKeeper has pre granted admission to the GateKeeper 0 Off 0 Off ARQ by the system 1 Out of Band 6 Not used Flash GK Time to Live 7 This parameter sets the duration between RRQ Registrar Request messages from 030 seconds 000 250 in 1 the VOIB to the GateKeeper as a keep alive message second increments 190 Issue 2 0 July 2010 PGM Flex Description Default Values 341 Btn GK Address 8 This parameter defines the IP address of the hosting GateKeeper 0 0 0 0 IPv4 address GK Find Address 9 This parameter defines the well known IP address for the system to locate a local 224 0 1 41 IPv4 address GateKeeper GK Find Port 10 This parameter defines the port used with the IP address of Flexible button 9 1718 0000 9999 GK RAS Sign
67. 0 disables the restriction Alarm Attribute 10 If this parameter is set to On the station receives alarm signals See 163 for 0 Off 0 Off Barge In Mode 13 This parameter configures Barge in capabilities for the station Barge in may be 0 Disable 0 Disable disabled set for a one way connection Monitor or a two way connection Speech 1 Monitor In the Monitor mode the user may release the mute condition to be heard 2 Speech Auto Forward to 14 When enabled On calls to the station forward to the station VMIB Mailbox when 1 On 0 Off VMIB the FWD to VMIB timer PGM 181 Flexible button 20 expires 1 Station Port 15 If this parameter is set to On the station port is disabled and any connected station 0 Off 0 Off Block is out of service 1 Preset MSG 16 If enabled On activating Absent Text Messages at the station also places the 1 On 0 Off DND station in DND 1 31 Issue 2 0 July 2010 Flex Description Default Values 113 Btn amp 17 When enabled a user can record Page announcement then call for the user s 0 Off 0 Off greeting and dials 8 The call is Parked and the Page announcement is played 1 allowing the user to access the call from the Park orbit Call Coverage 18 The Call Coverage parameter enables coverage for the Covered station Stations 0 Off 0 Of
68. 1 12 This parameter controls how the ip 60 will generate the Id for an ISDN or IP line 0 Normal 0 Normal call The CLI Type can be 1 Long CLI 1 0 Use COLP CLIP Table index Flexible buttons 1 amp 2 above 2 Long CLI 2 1 Use Long CLI 1 PGM 114 Flexible button 21 2 Use Long CLI 2 PGM 114 Flexible button 22 Reserved 13 Screening 14 This parameter defines the value used as the Screening Indicator element of the CLI 0 User provided 0 User provided Indicator field in the ISDN Setup message for an outgoing call No service No service 1 User provided Pass 2 User provided Fail 3 Network provided Double CLI 15 This parameter determines if the system will display the original CLI or Transit CLI 0 Transit 0 Transit Service for calls rerouted forwarded by the ISDN or IP line 1 Original Prefix Table 16 This parameter enables Prefix dialing and defines the Enblock Prefix Table PGM 0 Off 0 OFF Index 205 index to use for the CO line Intended for Ukraine only 1 6 Table Index Deny Incoming 17 A CO line can be configured not recognize an incoming call 0 Off 0 Off Call 1 ICLID 18 A CO Line can be configured to route a call based on the Incoming Caller ID ICLID O Off 0 Off The ICLID is compared to the ICLID Table entries PGM 237 to determine routing 1 Drop if No CLI 19 A CO Line can be configured to drop a call if the CO line does not prov
69. 179 defines Linked Station pairs the Linked pair stations act as a single station with a single station number Procedure 1 Press the TRANS button 2 Dial 179 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 179 Btn Display Linked 1 This Flexible button displays the Linked Pair stations use the Volume Up Down Pairs buttons to navigate Linked Pairs 2 This parameter assigns two stations as a Linked pair with the properties of the first None assigned Two station numbers station Main entered for the pair The Main station of a Linked Pair having a Main amp linked wireless station must be the wired station 115 Issue 2 0 July 2010 3 5 21 System Timers PGM 180 184 3 5 21 1 System Timers 180 PGM 180 is one of three PGMs used to define timers that affect system wide operations See also PGM 181 and 182 Procedure 1 Press the TRANS button 2 Dial 180 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 180 Btn Attendant Recall 1 This parameter sets the duration a call recalls to the Attendant before it is 01 minutes 00 60 in 1 minute Timer disconnected Calls can recall from Hold Transfer etc increments Call Park Recall 2 This parameter sets the duration a
70. 186 3 12 2 GateKeeper Settings 341 190 3 12 3 SIP Attributes 500 PC Admin 193 3 12 4 SIP Attributes 501 PC Admin 196 3 13 RSG IP Phone 380 397 0 4 198 3 13 1 VOIB Slot Assignment RSG IP Phone 380 198 3 13 2 RSG IP Phone Ports Assignment 381 199 3 13 3 RSG IP Phone Attributes F PGM 9382 200 3 13 4 IP Phone Attributes PGM 386 00 202 3 13 5 RSG IP Phone Tx amp Rx Gain Control PGM 396 and 397 204 3 14 Nation Specific Gain Tone Tables 400 424 206 Issue 2 0 July 2010 3 15 Initialization 450 sees enne nnnm nnn nnn 216 3 16 Print Prot Database 451 4 218 3 17 Initialize Database by MPB Version 452 220 ADMIN REFERENCE CHARTS naa 221 4 1 Admin Program Code 1 221 4 2 Default Flexible Number 227 QUICK REFERE
71. 190 PGM 190 assigns the type of Station group member stations and the Pick up attribute for each Station Group Procedure 1 Press the TRANS button 2 Dial 190 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 190 Btn Group Type 1 This parameter determines the type of Station or Hunt Group Not assigned 0 Not Assigned 1 Circular 2 Terminal 3 UCD 4 Ring 5 VM 6 Pick up 7 Networking VM Pick up Attribute 2 When enabled On stations in the group can Pick up calls for other stations in the 0 Off 0 Off group The Pick up attribute has no affect on Station Pick up groups 1 Member 3 This parameter assigns stations to the group Stations are assigned individually by None assigned Flexible button 1 24 129 Issue 2 0 July 2010 PGM Flex Description Default Values 190 Btn Assignment selecting a Flexible button or as a range Use the Volume Up Down button to scroll station number or the list of stations Enter a station range 130 Issue 2 0 July 2010 3 7 2 Procedur 1 n ves 3 7 2 1 PGM 191 Station Group Attributes PGM 191 PGM 191 defines the attributes of each Station Group based on the Type of group PGM 190 as shown in sections 3 7 2 1 3 7 2 6 Press the TRANS button Dial 191 Select the desired Flexible butto
72. 2 2 Separate LCR treatments are assigned for each time zone under PGM 221 and 2 digt pair 00 24 223 Time is assigned in 24 hour format with 00 amp 24 as midnight Any hour not covered by the time zones entered is treated as part of time zone 1 Time zones for 5 This parameter assigns three time zones for the day of week grouping 3 Day Zone Flexible button 1 3 Day Zone 3 3 Separate LCR treatments are assigned for each time zone under PGM 221 and 223 Time is assigned in 24 hour format with 00 amp 24 as midnight Any hour not covered by the time zones entered is treated as part of time zone 1 2 digt pair 00 24 149 Issue 2 0 July 2010 3 9 3 2 Leading Digit Table PGM 221 PGM 221 configures the Leading Digit Table LDT that defines digit strings to match with user dialed digits For each string a DMT index is assigned for each time zone of each Day grouping The Leading Digit Table provides for up to 250 entries Procedure 1 Press the TRANS button 2 Dial 221 3 Dialthe LDT index 000 249 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 221 Btn LCR Type 1 This parameter defines the LCR access modes that apply to this digit string The Both 1 Internal types are Internal any CO line access mode or both 2 CO 3 Both LCR Code 2 This parameter defines the digit string to m
73. 3 Issue 2 0 July 2010 PGM Flex Description Default Values 167 Btn Tone an Attendant or a Station Hunt Group When selecting Hunt Group enter the 2 Attendant Hunt Group number 3 Hunt Group enter group number DND Destination 4 This parameter defines the destination when a DID or DISA call encounters DND 1 Tone Flexible button and no forwarding destination is enabled The destination can be busy Tone an 1 Tone Attendant or a Station Hunt Group When selecting Hunt Group enter the Hunt 2 Attendant Group number 3 Hunt Group enter group number VMIB Prompt 5 The VMIB includes prompts that play when the destination is busy invalid error in Select Flexible Flexible button Usage DND does not answer or is transferred to an Attendant Each prompt is separately button 1 Busy Prompt enabled When enabled the VMIB announcement will be presented to the 2 Error Prompt caller before the call is routed to the assigned destination 3 DND Prompt 4 No answer 5 Attendant Xfer Busy Prompt 5 1 1 On 0 OFF 1 Error Prompt 5 2 1 On 0 OFF 1 DND Prompt 5 3 1 On 0 OFF 1 No Answer 5 4 1 On 0 OFF Prompt 1 ON Attendant 5 5 1 On 0 OFF Transfer Prompt 1 ON Reroute Busy 6 This parameter defines the destination when a DID or DISA call is rerouted with 2 Attendant Flexible button Issue
74. 3 5212 System Timers Il POM 181 oin nete co otiose Cete 119 3 5 21 3 System Timers Ill PGM 182 2 racer atte ERR tg 122 3 5 22 InsRoom Indication PGM 183 e ee eee 124 3 5 23 Chime Bell Attributes PGM 194 neo ea HI a ook cde atre 125 3 6 DCOB ATTRIBUTE 186 PGM 187 126 3 6 1 Attributes 180 tele aee 126 34 JDGOB Audnbutes o etra nc re eh er 128 3 7 Station Group 190 PGM 191 129 3 7 1 Station Group Assignments 190 129 3 7 2 Station Group Attributes 191 131 3 7 2 1 Circular amp Terminal Hunt Group Attributes 9 131 3 7 2 2 ACD UCD Hunt Group Attributes oed Ere oe Cl ht ee aed id Seba et 133 Ping GROUP cont ine er aus xe fr cause 136 3 5244 VM Group AUFIDUIGS pruden Re cut ius door ues pa 138 3 2 PICKUP Group sodass Gri E xd ease 139 3 7 2 6 Network VM Group 2 2 140 3 8 ISDN System Base Programs 200 202 141 3 8 1 System ISDN Attributes 200
75. 316 22 DTIB16 33 E1HB8 17 DSIB8 40 Station ID Code CO Line ID Code Misc ID Code T1 PRI PRIH8 17 DSIB8 31 T1HB8 17 05188 50 SLIB8 14 VMIU 64 AAFU 65 VOIB 41 For use only as Expansion board in second cabinet EKSU _ Slot Number Chart Slot Slot Location Type of Board Supported 1 01 BKSU board station slot Hybrid 02 BKSU Expansion board station slot Hybrid SLIB8 SLIB16 03 EKSU w EMU Main board station slot Hybrid EKSU w EMU2 Main board station slot DTIB16 04 EKSU w EMU Expansion board station slot Hybrid SLIB8 SLIB16 EKSU w EMU 2 Expansion board station slot Hybrid DTIB16 05 BKSU Main board CO line slot Analog CO 06 BKSU Expansion board CO line slot Analog CO E1 T1 or PRI 07 EKSU Main board CO line slot Analog CO 08 EKSU Expansion board CO line slot Analog CO 09 VMIB or AAFB VMIB or AAFU 10 VOIB VOIB Issue 2 0 July 2010 Issue 2 0 July 2010 3 1 3 Logical Slot Assignment 103 PGM 103 defines the logical order and therefore logical port numbers associated with a slot To support IP Phones assign slot 99 Virtual VMIB as a Station board in the desired logical order The system will allocate station numbers to the system using the number of IP Phones entered PGM 381 Procedure 1 Press the TRANS PGM button 2 Dial 103 3 Select the desired Flexib
76. 4 VMIB Annc 62 Issue 2 0 July 2010 PGM Flex Description Default Values 141 Btn number 5 Virtual VMB number Preset Forward 15 When desired CO Line Preset Forward can send calls to an external Voice Mailbox 0000 0000 9999 Voice Mail Id using the Voice Mailbox Id assigned here 63 Issue 2 0 July 2010 3 3 3 CO Line Attributes 11 142 PGM 142 is one of three PGMs to assign general attributes to the CO line range Also see PGMs 141 and 146 Procedure 1 Press the TRANS PGM button 2 Dial 142 3 Enter the appropriate CO line Range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 142 Btn CO Line Name 1 When enabled On the assigned CO Line Name Flexible button 2 displays in the 0 Off 0 Off Display DKT LCD for incoming calls on the CO line 1 CO Line Name 2 This parameter assigns the name for the CO line The name can be up to 12 No assignment 12 characters Assign characters Refer to the Dial Pad Character chart below for dial pad entries Metering Unit 3 This parameter defines the type of Metering Signal the system expects to receive 00 None 00 None from the PSTN 01 50 Hz 02 12 2 03 16 KHz 04 Singular Polarity Reverse SPR 05 Plural Polarity Reverse PPR 06 No Polarity 64 Issue 2 0 July 2010 PGM
77. 4 3 2 19 Display Station Numbers by COS 130 57 3 2 20 Display Station Numbers by CO Group Access 131 58 3 4 GO Eine POM 140 144 iioii 59 3 3 1 Service Type 140 59 3 3 2 Line Attributes PGM 141 61 3 3 3 Line Attributes JE PGM 142 isse oder eoe rao ed ce 64 3 34 ISDN IP CO Line Attributes 143 2 2 1 68 3 3 5 CO Line Ring Assignment 144 71 3 36 COLine Ring Assignment Display 145 72 3 3 7 CO Line Attributes PGM 146 73 3 3 8 Line Caller Id CID Attributes 147 75 3 3 9 T1 CO Line Attributes PGM 152 reni eek tn cube needs 77 3 4 Board Slot Based Admin 155 1 2111 79 3 4 1 T1 DCO Board Attributes 155 79 3 5 System Data 160 184 irn seen kc n cuu o a va in x dun d c rua Mua ra qu pex coude 81 3 5 1 System Attributes PGM 160 terere o creacion da ene 81 3 5 2 System Attributes 161 eene 84 3 5 3 Admin Password PGM 162 0 1 teed dU dices o taut 87 3 5 4
78. 7 1 20 Issue 2 0 July 2010 3 2 Station 110 131 3 2 1 Station Id Name amp DSS DLS Map PGM 110 PGM 110 defines the type of terminal employed for a range of stations In addition where a station has an associated DSS Console one of three maps or templates establishes the default configuration of the Flexible buttons Procedure 1 Press the TRANS PGM button 2 Dial 110 3 Enter the appropriate Station Range 4 Select the desired Flexible button from the chart below 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 110 Btn Station ID 1 This parameter defines the type of terminal attached and must be assigned if other DKTU or SLT 01 DKT than default DKTU o SLT 05 ICM Box 07 SLT DTMF 08 SLT PULSE 12 SLT CID FSK 13 SLT CID DTMF 14 IP Phone Station Name PC This parameter assigns the display name for the station the station LCD while idle 12 characters 21 Issue 2 0 Directory Last with the Company Directory Use two digits for each character as shown in the Dial July 2010 PGM Flex Description Default Values 110 Btn admin displays the Station and internal parties may receive the Station Name the only LCD DSS DLS 2 This parameter assigns the Flexible button map or template employed for the DSS 02 02 DSS MAP 1 Console associated with the
79. Alarm Attributes PGM 163 idiot etel de o pete pee opted 88 3 5 5 System amp Main Attendant Assignments 164 89 3 5 6 Auto Attendant Announcement 165 90 3 5 7 COSTO CO COS POM 166 che a ah cer qt ambae 91 3 5 8 DID DISA Destination 167 93 3 5 9 External Control Contacts 168 96 Issue 2 0 July 2010 3 5 10 LCD Time Date and Language Mode 169 97 3 5 11 Modem Assignment 170 2 22 000000 99 3 5 12 Music Assignments PGM 17 T 100 3513 PBX Access Codes PGM 172 eret 103 3 5 14 PLA Priority Setting 173 5 cicer tse kukogues 104 3 5 15 RS 232C Port Setting 1 74 eerte one 105 3 5 16 Print Port Selection 75 107 3 5 17 Pulse Dial Ratio 176 109 3 5 18 SMDR Altributes POM a E Cop GR EE D na d Hn 110 3 5 19 System Time and Date 178 40244 114 3 5 20 Linked Station Pairs PGM 179 as iiid c Evae Ha eto 115 3 5 21 System Timers 180 184 0 020 116 3 5 21 1 System Timers 180 tinxit Rr I ta E EE IER 116
80. COS 3 This parameter defines the Night mode Station COS associated with the 1 9 Authorization Code 160 Issue 2 0 July 2010 3 96 Customer Call Routing 228 PGM 228 defines the routing for each CCR Table Procedure 1 Press the TRANS button 2 Dial 228 3 Enter the Table number 01 07 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 228 Btn Digit 1 1 This parameter defines the CCR destination when the DISA caller dials the digit 1 Not assigned See CCR Destination Code Table Digit 2 2 This parameter defines the CCR destination when the DISA caller dials the digit 2 Not assigned See CCR Destination Code Table Digit 3 3 This parameter defines the CCR destination when the DISA caller dials the digit 3 Not assigned See CCR Destination Code Table Digit 4 4 This parameter defines the CCR destination when the DISA caller dials the digit 4 Not assigned See CCR Destination Code Table Digit 5 5 This parameter defines the CCR destination when the DISA caller dials the digit 5 Not assigned See CCR Destination Code Table Digit 6 6 This parameter defines the CCR destination when the DISA caller dials the digit 6 Not assigned See CCR Destination Code Table Digit 7 7 This parameter defines the CCR destination when the DISA c
81. Control 414 SLIB Gain Control 415 5 ACO Gain Control 416 Long ACO Gain Control 417 MBU DSP RX Gain 418 MBU FSK TX Gain 420 5 Tone Frequency 421 Differential Ring Frequency 422 Distinct 423 ACNR Tone Cadence 424 Rx From ACO Gain Control INITIALIZATION 450 Initialization PRINT DATABASE 451 Print Port Database INITIALIZE BY MPB VERSION 452 Initialize for specific MPB S W version 3 7 or 3 8 226 Issue 2 0 July 2010 Issue 2 0 July 2010 4 2 Default Flexible Number Plans Flexible Numbering Plans Chart Flexible Plan1 Plan2 Plan3 Plan4 Plan5 Plan6 Plan Plan 8 105 Station Numbering 100 100 100 700 200 10 100 100 147 147 147 747 247 57 147 147 106 1 Station Group Pilot Range 620 620 620 620 620 620 620 620 629 629 629 629 629 629 629 629 2 Internal Page Zone Range 501 501 01 01 01 501 401 501 510 510 10 10 10 510 410 510 3 Internal All Call Page 543 543 as Jaz as 643 43 553 4 Meet Me Page 544 544 HH 544 44 44 5 External Page Zone 545 545 6 41 6 545 45 545 6 All Call Page Intern
82. DCOB SLIB 26 00 63 3 Reserved 4 DCOB WTIB 26 00 63 5 DCOB ACOB 15 00 63 6 Reserved 7 DCOB DCOB 32 00 63 8 DCOB VMIB 32 00 63 209 Issue 2 0 July 2010 Flex Description Default Values 406 DCOB Gain Btn 9 DCOB DTMF 32 00 63 10 DCOB TONE 32 00 63 11 DCOB MUSIC1 32 00 63 12 DCOB MUSIC2 32 00 63 13 Reserved 14 DCOB MODEM 37 00 63 PGM Flex Description Default Values 407 VMIB Gain Btn 1 VMIB DTIB 21 00 63 2 VMIB SLIB 21 00 63 3 Reserved 4 VMIB WTIB 26 00 63 5 DCOB ACOB 23 00 63 6 Reserved 7 DCOB DCOB 32 00 63 8 DCOB MUSIC1 32 00 63 9 DCOB MUSIC2 32 00 63 PGM Flex Description Default Values 408 DTMF Gain Btn 1 DTMF Rx DTIB 32 00 63 2 Reserved 3 DTMF Rx ACOB 32 00 63 4 Reserved 210 Issue 2 0 July 2010 Flex Description Default Values 408 DTMF Gain Btn 5 DTMF Rx DCOB 32 00 63 PGM Flex Description Default Values 409 External Btn Page Gain 1 External Page DTIB 26 00 63 2 External Page SLIB 26 00 63 3 Reserved 4 External Page WTIB 26 00 63 5 External Page ACOB 28 00 63 6 Reserved 7 External Page DCOB 37 00 63 8 External Page VMIB 37 00 63 9 External Page MUSIC1 37 00 63 10 External Page MUSIC2 37 00 63 11 Reserved
83. Defines the type of CO line and service This parameter defines DISA service for the various ring modes Select Flexible button Default Flexible button 1 DISA Service Values 1 Normal 2 T1 DID 3 ISDN DID MSN 4 TIE 5 DCO DID TIE ANI TIE DNIS 0 Off 1 59 Issue 2 0 July 2010 PGM 140 attributes TIE Line service T1 service attributes Flex Description Default Values 1 Day ring 0 Off 2 Night ring 3 Weekend Flexible button 2 VMIB Greeting 00 4 Lunch VMIB Greeting 70 5 On demand Not assigned Then select Flexible button 1 for DISA Service or Flexible button 2 to assign a VMIB Greeting This parameter determines the T1 DID line start signal 1 Immediate 1 Immediate 2 Wink start 3 Delayed dial This parameter determines the start signal for T1 TIE lines 1 Immediate 1 Immediate 2 Wink start 3 Delayed dial 60 Issue 2 0 July 2010 3 3 2 COLine Attributes 141 PGM 141 is one of three PGMs that assign general attributes to the CO line range Also see PGMs 142 and 146 Procedure 1 Press the TRANS PGM button 2 Dial 141 3 Enter the appropriate CO line Range 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 141 Btn CO line Group 1 This parameter defines the CO Group for
84. Flexible button is used to initialize all the LCR data None 154 Issue 2 0 July 2010 PGM Flex Description Default Values 223 Btn Initialize 155 Issue 2 0 July 2010 3 9 4 Table 224 226 Toll tables are used to enhance the basic COS restrictions by allowing and denying specific digit strings In Allow and Deny Tables 3 9 4 1 Toll Exception Tables 224 PGM 224 defines the Allow and Deny Tables A to D used to determine Class of Service Procedure 1 Press the TRANS button 2 Dial 224 3 Select the desired Flexible button 4 Enterthe table entry 5 Enter the desired Allow Deny number 6 Press the Hold Save button PGM Flex Description Default 224 Btn Allow Table A 1 This parameter selects a Table index and allowed digit strings for the Allow Table A Not assigned used in Station COS 2 4 and 11 Deny Table A 2 This parameter selects a Table index and denied digit strings for the Deny Table A Not assigned used in Station COS 2 4 and 11 Allow Table B 3 This parameter selects a Table index and allowed digit strings for the Allow Table B Not assigned used in Station COS 3 4 and 11 Deny Table B 4 This parameter selects a Table index and denied digit strings for the Deny Table B Not assigned used in Station COS 3 4 and 11 Allow Table C 5 This parameter selects a Table index and allowed digit strings for the Allow Table C Not a
85. Hidden 5 When enabled digits dialed by the station user are NOT output in SMDR records 0 Disable 0 Disable Dialed Digits 1 Enable Voice Over 6 When enabled the busy Station can talk alternately between two calling or called 0 Disable 0 Disable Issue 2 0 July 2010 PGM Flex Description Default Values 113 Btn parties Caller Voice Over must be enabled for the calling station 111 button 1 Enable 22 Warm Line 7 This parameter configures Idle Line Selection for the station for Hot Line immediate 0 Warm 0 Warm connection or Warm Line delayed for the Warm Line Time PGM 182 Flexible 1 Hot button 8 See also 122 for Idle Line Selection VMIB MSG 8 If this parameter is set to On the station user must enter their password to access 0 Off 0 Off Password the VMIB Voice Mailbox 1 9 If this parameter is set to On the VMIB will play the Date and Time stamp for each 1 On 0 Off Date Time message before playing the message 1 Alarm contact programming 1 Mute Ring 11 If this parameter is set to the station while busy receives mute ring for an 1 On 0 Off incoming call 1 Call Cut Off timer 12 This parameter defines the duration of an outgoing call when the station is assigned 0 minutes 00 99 minutes CO Call Time Restriction PGM 112 Flexible button 3 Time is set in minutes and a value of
86. In Off Off addition if User ID Registration is set to register the User ID will also be employed On 196 Issue 2 0 July 2010 PGM 501 Associated Station Flex Btn Description This parameter defines the station number associated with the SIP User Id when Centrex features are enabled see also PGM 500 IP Centrex Intended for use with Broad Works soft switch only Default Not assigned Values Station Number 197 3 13 RSG IP Phone PGM 380 397 3 13 1 VOIB Slot Assignment RSG IP Phone 380 PGM 380 defines the number of channels reserved for IP Phones Procedure 1 Press the TRANS button Dial 380 Select the desired Flexible button Enter the appropriate value Press the Hold Save button gt TT Issue 2 0 July 2010 Flex Description 380 Btn Default Values VOIB Slot for 1 This parameter defines the VOIB slot to employ for RSG modules and IP Phone RSG IP Phones ip 60 60 supports a single slot slot 10 10 10 Channels for 2 This parameter defines the number of VOIB channels reserved for RSG and IP RSG IP Phones Phones Not assigned 0 4 w VOIB 0 8 w VOIB amp VOIU 198 Issue 2 0 July 2010 3 13 2 RSG IP Phone Ports Assignment 381 PGM 381 defines the number of IP Phones Procedure 1 Press the TRANS button Dial 381 Select the desired Flexible button En
87. LCD Date Time Language Display Mode 170 Modem 171 Music 172 PBX Access Code 173 PLA Priority Setting 174 RS 232C Port Setting 175 Print Port Selection 176 Pulse Dial Ratio 177__ 5 Attributes 178 System Date Time Setting Linked Station Pairs Table 180 System Timers 1 SYSTEM TIMERS 1 System Timers II 1 182 System Timers Ill 1 Room Indication 184 Bell Attribute DCOB ATTRIBUTES 186 DCOB System attribute 187 CO Line Attribute TION GROUP 190 Station Group Assign 191 Station Group Attribute 223 Issue 2 0 July 2010 ISDN SYSTEM BASE 200 System ISDN Attribute COLP Table Entry 202 MSN Table Attribute 204 Local Code Table 205 Enblock Prefix Table 220 LCR Attributes 221 LCR Leading Digit Table 222 LCR Digit Modification Table 223 LCR Table Initialization Exception Table Allow Entry 01 50 Exception Table Deny Entry no 01 50 Toll Exception Table Allow B Entry no 01 50 Exception Table Deny B Entry no 01 50 225 Canned Table Allow Entry 01 20 Canned Toll Table Deny Entry 01 20 226 Emergency Code Table 227 Authorization Code Table 228 Customer Call Routing 224
88. LI 0 CLI Display Calling Line Id or the Id of the line redirecting the call RED 1 Redirect CLI MSG Wait 4 If this parameter is set to On a CLI message is activated when the station does not 0 Off 0 Off answer an incoming ISDN or IP CO line call 1 5 When the Table Index 143 Flexible button 2 is 50 the system sends 0 EXT 0 Extension either the station number EXT or the CO line Attendant station number as the Id 1 Attendant Keypad Facility 6 This parameter determines if digits dialed after the called is connected are sent as 0 DTMF 0 DTMF 33 Issue 2 0 July 2010 PGM Flex Description Procedure Values 114 Btn normal DTMF tones or as part of the Keypad Facility message 1 Keypad Long Short 7 Not used CPN Type 8 not available Reserved 9 DISA Restriction 10 If this parameter is On the station cannot receive calls from a DISA line 0 Off 0 Off 1 11 When enabled if the received matches a Speed Dial number for the 0 Off 0 Off Display station the station LCD displays the Name of the Speed Dial 1 ISDN STA 12 When the CLI Type Flexible button 17 is Short and the is set as EXT Flexible Station number Up to 4 digits button 5 this entry up to 4 digits is the sent by the system Progress 13 When enabled On
89. Loop 0 Open Loop 0 Open Loop Flash or Ground The duration is set in PGM 142 Flexible button 12 1 Ground UNA Universal 8 When enabled On CO line is subject to UNA service a station may answer calls 0 Off 0 Off Night Answer using the UNA code 1 CO Line Group 9 When enabled an Authorization code must be entered to place a call on CO 0 Off 0 Off Account lines 1 10 This parameter assigns CO lines for the exclusive use by stations an Intercom 0 all groups 0 All groups Tenancy Group 1 5 Group 1 5 E911 Use 11 Enhanced 911 location support is not available CO Line Start 12 Analog CO Lines can be configured to recognize a Loop closure or Ground 0 Loop 0 Loop Signal connection as the signal indicating 1 Ground Preset Forward 13 This parameter defines the Preset Call Forward time for CO Line Preset Call 25 25 seconds 00 99 seconds Timer Forward After the timer expires if the call is unanswered the call is sent to the destination defined in PGM 141 button 14 below Preset Forward 14 This parameter defines the destination for CO Line Preset Call Forward If the 0 0 Not assigned incoming CO call is not answered within the Preset Call Forward timer PGM 141 Flexible button 13 the call is sent to the assigned station Voice mailbox VMIB announcement or Station Hunt Group 1 Station number 2 Station Voice Mailbox number 3 Hunt Grp number
90. MOH 9 Hold tone ACD Warning 12 When enable if an ACD Supervisor intrudes on a busy group member a tone 1 On 0 Off Tone indicating the intrusion is provided to the call parties 1 Alternate 13 This parameter assigns the Alternate destination when calls are received and no Not assigned 1 station number destination members are on duty or all members are busy 2 Hunt Group Supervisor Timer 14 This parameter defines the delay before the Supervisor DKT LCD displays the 030 seconds 000 999 queued call count if the number of calls exceeds the Supervisor Call Count see Flexible button 15 Supervisor Call 15 This parameter defines the number of queued calls that activates the Supervisor 00 disabled 00 99 timer Flexible button 14 for display of the queued call count A setting of 00 disables the Supervisor Call Count feature ACD Queued 16 When enabled On the Supervisor DKT LCD will display the Queued call count for 1 On 0 Off Call the group 1 Queued Call 17 This parameter determines the maximum number of calls that can queue to the 99 00 99 Count Group When the queued calls exceed the Maximum Queued Call Count additional calls are ignored Supervisor 18 This parameter assigns a station as the ACD Group Supervisor Not Assigned Station number UCD hunt 19 This parameter determines the priority of the member from 0 the highest priority to 9 Not assigned Flexible button 1 48
91. NCE CHARTS 3 tranne eet eoe eoe ana eei nne 230 5 1 Station User Program 230 5 2 Attendant User Program 233 5 3 Flexible Button Program nne 235 Issue 2 0 July 2010 1 MANUAL INTRODUCTION This manual provides detailed information related to configuring the system database through Admin Programming Program parameter descriptions in Section 3 are appropriate for both a Digit Key Telephone and the ip 60 PC Admin The step by step procedures in this manual are given for DKT programming For PC Admin procedures refer to the PC Admin User manual This manual is divided in to five 5 sections Manual Introduction Admin Programming Overview Admin Programming Procedures Admin Programming Index User and Attendant Station Programming Charts 1 1 Section Descriptions 1 1 1 Manual Introduction Section 1 this section is an introduction to the manual It provides a description and purpose for each of the sections of the manual 1 1 2 Admin Programming Overview Section 2 is an overview of Admin programming how the various Programs 5 are grouped and general information on using a DKT for access and modifying parameters It includes a brief discussion of the function of the DKT buttons while in the
92. Networking CO Line Attributes 322 PGM 322 establishes characteristics of CO lines used for Private Networking Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 322 3 Enter the CO line range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 322 Btn Networking CO 1 This parameter defines the Network CO line Group number This parameter does 00 00 24 Line Group not relate to the normal CO line Group number VOIB Mode 2 This parameter defines the VolP protocol used by the VOIB on CO lines H 323 or 1 SIP 0 H 323 SIP 1 SIP Use Gatekeeper 3 When enabled On the system employs the GateKeeper to route calls Otherwise 0 Off 0 Off the call is routed directly over the network 1 Networking CO 4 This parameter defines the type of system connected to a networked system CO 0 PSTN 0 PSTN Line Type line PSTN or Networked system 1 Network DTMF Mode 5 This parameter defines the DTMF signaling mode employed on the CO line for 2 In band 2 In band DTMF networking DTMF 3 RFC2833 4 Out band DTMF 183 Issue 2 0 July 2010 3 11 4 Network Routing Network Numbering Plan Table 324 PGM 324 establishes the routing for each Network Numbering Plan code Procedure 1 Press the TRANS button 2 Dial 324 3 Enter the Network Nu
93. Not assigned DKT station number the Speed button Main Attendant 4 5 This parameter defines the fourth Main Attendant To delete a Main Attendant Not assigned DKT station number press the Speed button 89 Issue 2 0 July 2010 3 5 6 Auto Attendant VMIB Announcement 165 PGM 165 configures the back up Auto Attendant Announcement used when the Attendant does not answer an incoming CO line call Procedure 1 Press the TRANS button 2 Dial 165 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 165 Btn Auto Attendant 1 If this parameter is On the back up Auto Attendant is enabled and will play the 0 Off 0 Off Usage assigned VMIB announcement refer to Flexible button 2 1 VMIB Announce 2 This parameter defines the VMIB announcement used for the back up Auto Not assigned 00 70 Attendant 90 Issue 2 0 July 2010 3 5 7 CO To CO COS 166 PGM 166 assigns the Day and Night Weekend service mode COS for a CO to CO connection Unsupervised Conference Procedure 1 Press the TRANS button 2 Dial 166 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 166 Btn CO to CO Day 1 This parameter defines the CO to CO Day mode COS Refer to the ta
94. On for all LCR Modes except M13 the system will verify dial tone 0 Off 0 Off Detect on an analog CO line if dial tone is not received the Alternate DMT Index is used to 1 route the call Transit Out 23 When enabled the system will verify the IP address in the Transit Out set up 0 Off 0 Off Security message received by the VOIB is from a registered IP address If not registered the 1 Transit Out call will fail 86 Issue 2 0 July 2010 3 5 3 Admin Password 162 PGM 162 assigns a password to access Admin programming Procedure 1 Press the TRANS button 2 Dial 162 3 Enter the appropriate value 4 Press the Hold Save button PGM Flex Description Default Values 162 Btn Admin Password This parameter defines the password if any required for a user to access Admin Not assigned 4 digits programming The password must be 4 digits To delete a password press the 0 9 Speed button 87 Issue 2 0 July 2010 3 5 4 Alarm Attributes PGM 163 PGM 163 configures the Alarm contact in the main cabinet Procedure 1 Press the TRANS button 2 Dial 163 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 163 Btn Alarm Enable 1 If this parameter is the system will monitor the external Alarm contact 0 Off 0 Off 1
95. S button 2 Dial 186 3 Enter the appropriate CO Line range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 186 Btn DCOB TYPE 1 See PGM 187 Flexible button 4 Metering 2 When enabled this parameter enables the use of Call Metering signals Also 0 Off 0 Off see 142 Flexible buttons 3 1 R2 OUT Manage 3 This parameter sets the time the system will wait for a backward signal from an 14 seconds 01 50 in 1 second Timer E1R2 CO line after sending a forward signal an outgoing call increments R2 IN Manage 4 This parameter sets the time the system will wait for a forward signal from an E1R2 14 seconds 01 50 in 1 second Timer CO line after sending a backward signal on an incoming call increments R2 Disappear 5 This parameter defines the duration the system will allow to complete R2 signaling 14 seconds 01 50 in 1 second Timer increments R2 Pulse Timer 6 This parameter sets the duration of pulse dial signals sent over an ETR2 Co line 07 140 milli 01 30 in 20 milli 126 Issue 2 0 July 2010 PGM Flex Description Default Values 186 Btn seconds second increments R2 Ready Timer 7 This parameter determines the time between receipt of a line seize and seize 007 140 milli 000 500 in 20 milli acknowledge signal
96. SG IP Phone Tx amp Rx Gain Control 396 and 397 PGM 396 and 397 establish Transmit and Receive audio gain for IP Phones Procedure 1 Press the TRANS button 2 Dial 396 or 397 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 396 Btn 1 RSG IP Phone RX from DKTU 26 00 63 2 RSG Phone RX from SLT 33 00 63 3 RSG IP Phone RX from CTR SLT 22 00 63 4 RSG IP Phone RX from WKT 26 00 63 5 RSG IP Phone RX from ACO 33 00 63 6 RSG IP Phone RX from CTR ACO 22 00 63 7 RSG IP Phone RX from DCO 33 00 63 8 RSG IP Phone RX from VMIB 29 00 63 9 RSG IP Phone RX from DTMF 08 00 63 10 RSG IP Phone RX from TONE 32 00 63 11 RSG IP Phone RX from MUSIC 1 29 00 63 12 RSG IP Phone RX from MUSIC 2 29 00 63 13 RSG IP Phone RX from R DKT 26 00 63 14 RSG IP Phone RX from R SLT 22 00 63 204 Issue 2 0 July 2010 PGM Flex Description Default Values 396 Bin 15 RSG Phone RX from R_LCO 22 00 63 16 RSG Phone RX from IP Phone 26 00 63 PGM Flex Description Default Values 397 Btn 1 RSG Phone TX to DKTU 26 00 63 2 RSG Phone TX to SLT 33 00 63 3 RSG Phone TX to CTR SLT 22 00 63 4 RSG Phone TX to WKT 26 00 63 5 RSG
97. Stations Priority the lowest priority Members with higher priority receive group calls before lower 1 9 priority members Hunt Member 20 When enabled On a member with Call Forward active will not receive Hunt Group 1 On 0 Off forward calls the member is considered unavailable for group calls 1 UCD DND Timer 21 This parameter sets the duration a station will receive ring before the system places 000 seconds 000 999in 1 second 135 Issue 2 0 July 2010 PGM 191 Flex Description Default Values ACD UCD Btn the station UCD DND and unavailable for group calls A setting of 00 disables increments automatic ACD DND Queued call Tone 22 When enabled On the first group member assigned in Program 190 for the group 0 Off 0 Off receives a single 0 4 second burst of muted ring when a call is queued to the group 1 23 This parameter assigns a name maximum 12 characters to the group Not assigned 12 Characters Assign Call Coverage 24 The Call Coverage parameter enables coverage for the Hunt Group A Call Button 1 0 Off 0 Off Coverage Flexible button at a covering station for the group will be active The 1 covering station must have a Coverage button set using Station User Program Button 2 0 0 9 cycles codes 46 and group number Flexible button 1 Hunt Coverage Mode On Off Flexible button 2 Delay Ring Cycle 3 7 2 3 Ring Group Attr
98. Stations are assigned to receive pages from any combination of the five Conference Zone Page Zones The Flexible button toggles access to the Zone and the LED indicates Zone membership On Zone member Off Not Zone member Default No Access Values Flexible button 1 5 43 Issue 2 0 July 2010 3 2 11 Intercom Tenancy Group 120 PGM 120 configures the Attendant station for each of the five 5 Intercom Tenancy Groups and defines other Tenancy Groups that can be called by stations in a specific Tenancy Group Procedure Tenancy Group Attendant Press the TRANS PGM button Dial 120 Press the Flexible button for the Tenancy Group 1 5 Press Flexible button 1 to assign an Attendant for the Tenancy Group Enter the station number desired Press the Hold Save button I disc 19223 Tenancy Group Access 1 Press the TRANS PGM button 2 Dial 120 3 Press the Flexible button for the Tenancy Group 1 5 4 Press Flexible button 2 to assign Tenancy Group access 5 Press the Flexible button for the Tenancy Group 1 5 to enable disable access 6 Press the Hold Save button PGM Flex Description Default Values 120 Btn 1 Any DKT station can be assigned as the Attendant for an Intercom Tenancy Group No assignment Station number 44 Issue 2 0 July 2010 PGM 120 Attendant Tenancy Group Access Flex Btn
99. Table is monitored for Allow and Deny numbers 6 The leading digits cannot be a Long Distance code Only eight digits maximum can be dialed In addition the Canned Toll Table is monitored for Allow and Deny numbers 7 Intercom and paging calls are allowed No dialing is allowed on CO lines except Emergency numbers Door Phones ICM boxes should be assigned with this COS 8 The assignments in the Exception Table C are monitored for allow and deny numbers 9 The assignments the Exception Table D are monitored for allow and deny numbers 10 The assignments in the Exception Table C amp D are monitored for allow and deny numbers 11 The assignments in the Exception Table A amp D are monitored for allow and deny numbers 40 Issue 2 0 July 2010 3 2 8 CO Line Group Access PGM 117 PGM 117 defines the CO line Groups available to a station The station user may access CO lines from the CO Group using dial codes or a Flexible button assigned to the CO Group Procedure 1 117 Press the TRANS PGM button Dial 117 Enter the appropriate Station Range Press the Flexible button to enable disable CO Group access Press the Hold Save button Flex Description Default Values Btn CO Line Group 1 24 lines are assigned to a CO Group 141 Flexible button1 Each station is All stations have Flexible button 1 24 assigned access to the CO Group and thus
100. al 11 This parameter defines the port used for the H 323 RAS Registration Admission 1719 0000 9999 Port and Signal channel for the GateKeeper GK Signal Port 12 This parameter defines the port used by the GateKeeper for H 323 signals 1720 0000 9999 VOIB GK ID 13 This parameter assigns the unique identification of the GateKeeper for the ip 60 Not assigned Up to 23 characters see Dial Pad Character Chart VOIB H323 ID 14 This parameter assigns a unique H 323 identification to the VOIB Not assigned Up to 23 characters see Dial Pad Character Chart VOIB E164 15 This parameter registers one or more stations with the GateKeeper Enter the Not assigned Up to 23 characters Address station number or enter the first digit of a range of stations 2 2000 2999 In see Dial Pad addition when registering a range of stations the VOIB Terminal Alias must be Character Chart assigned VOIB Terminal 16 This parameter is used to register a range of stations with the GateKeeper Enter Not assigned Flexible button 1 4 Alias the first digit of the range of stations to be registered 2 2000 2999 Dial Pad Character Chart 191 20 digits 0 9 Issue 2 0 July 2010 2 12 4 40 G 41 H 42 1 43 7 70 P 71 Q R 73 74 0 Blank 1 U x2 192 Issue 2 0 July 2010 3 12 3 SIP Attributes 500 PC Admin only 500 is one of two PGMs used to co
101. al External 549 549 00 6 00 549 49 549 7 SMDR Account Code 550 550 550 550 50 550 50 550 8 Flash Command to CO Line 551 551 551 551 51 551 51 551 9 Last Number Redial LNF 552 552 552 552 52 552 52 552 10 Do Not Disturb 553 553 553 553 53 553 53 553 11 Call Forward 554 554 554 564 54 554 54 554 12 Speed Dial Program 555 555 555 40 55 555 55 555 13 Activate MSG Wait Call Back SLT 566 48566 556 566 56 556 56 556 14 MSG Wait Call Back Return Call SLT s557 557 557 567 57 557 57 4557 15 _ Speed Dial Access 558 558 558 7 58 558 58 558 227 Issue 2 0 July 2010 PGM Flexible Plan 1 Plan2 Plan3 Plan4 Plan5 Plan6 Plan Plan 8 Button 16 Cancel DND CFW Pre Selected MSG 559 559 559 559 59 559 59 5559 17 SLT Hold SLT only 560 560 560 560 690 560 30 560 18 Virtual Voice Mailbox 200 200 200 200 100 100 200 200 249 249 249 249 149 149 249 249 19 Reserved 20 SLT Program Mode Select SLT only 563 563 563 563 693 3 33 9 21 ACD Reroute 564 gt 564 564 564 64 4 34 4 PGM 107
102. aller dials the digit 7 Not assigned See CCR Destination 161 Issue 2 0 announcement 00 70 July 2010 PGM Flex Description Default Values 228 Btn Code Table Digit 8 8 This parameter defines the CCR destination when the DISA caller dials the digit 8 Not assigned See CCR Destination Code Table Digit 9 9 This parameter defines the CCR destination when the DISA caller dials the digit 9 Not assigned See CCR Destination Code Table Digit 0 10 This parameter defines the CCR destination when the DISA caller dials the digit 0 Not assigned See CCR Destination Code Table Busy Destination 11 This parameter defines the destination when the CCR destination is busy 1 Attendant Flexible button 1 3 Error Time out 12 This parameter defines the destination when the CCR destination is an error or the 1 Attendant 1 Tone Destination Inter digit time expires see PGM 181 Flexible button 8 2 Attendant No Answer 13 This parameter defines the destination when the CCR destination does not answer in 1 Attendant 3 Hunt Group Destination the DID DISA No answer time PGM 181 Flexible button 2 4 VMIB enter CCR Destination Table Destination Destination Values Code 01 Station 01 station number 02 Hunt Group 02 Hunt Group number 03 VMIB Announce 03 VMIB Announcement num
103. an be immediate Hot Line or delayed Warm Line Hot Warm Line operation is defined in PGM 113 Flexible button 7 The Warm Line delay is defined in PGM 182 Flexible button 8 Procedure Press the TRANS PGM button 1 25 00 PGM 122 Idle Line Selection Dial 122 Enter the appropriate Station Range Enter the desired Idle Line Selection Type and Value Press the Hold Save button Flex Btn Description This parameter defines the CO line station or Flexible button the system connects to the station when the station goes off hook Use the Delete softkey to remove an assignment and provide Internal dial tone Idle Line Select Table Default No assignment Internal dial tone Description 1__ button 01 44 Activate a feature of a Flexible button as if pressed 2 COLine 01 36 Access a CO Line 3 CO Line Group 01 24 Access a CO line from a CO Group 24 Station 100 147 station 47 Values 1 4 amp Value Range from Idle Line Select Table Issue 2 0 July 2010 3 2 14 SMDR Account Group 124 PGM 124 defines the SMDR Account Group for each station The SMDR record will include the Account Group SMDR record for calls to from the station Procedure Press the TRANS PGM button 2 Dial 124 3 Enter the appropriate Station Range
104. ansion cabinet The contact can be assigned to activate when 2 Doorbell A station receives a call with the system in Night Service 3 External Page Second Contact Third Contact Fourth Contact A doorbell contact is activated or External Page is accessed 96 Issue 2 0 July 2010 3 5 10 LCD Time Date and Language Mode PGM 169 PGM 169 defines the Time and Date display format and the display Language Procedure 1 Press the TRANS button 2 Dial 169 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 169 Btn LCD Time Mode 1 This parameter sets the display format for Time as a 12 or 24 hour clock 1 12 hour clock 0 24 hour clock 1 12 hour clock LCD Date Mode 2 This parameter sets the format of the date display as Day Month Year DD MM YY 0 DD MM Y Y 0 DD MM YY or Month Day Year MM DD YY 1 MM DD YY LCD Language 3 This parameter selects the language used in the LCD of the DKTs 00 English 00 English 01 Italian 02 Finnish 03 Dutch 04 Swedish 05 Danish 06 Norwegian 07 Hebrew 08 German 09 French 97 169 Btn Description 98 Default Issue 2 0 July 2010 Values 10 Portuguese 11 Spanish 12 Korean 13 Estonia 14 Russian 15 Turkish 16 Romanian 17 Polish Issue 2
105. ant DND Networking Only 56 Attendant Camp On Queue BTN Assignment Attendant 57 Call Log Display 61 Record VMIB User Greeting 64 Listen VMIB Station Status 66 Erase VMIB User Greeting 235 Issue 2 0 July 2010 8 supervisor should be assigned 91 CONF BTN Assignment 2 amp 8 Button 92 CALLBK BTN Assignment 2 amp 8 Button 93 DND FWD BTN Assignment 2 amp 8 Button 94 FLASH BTN Assignment 2 amp 8 Button 95 MUTE BTN Assignment 2 amp 8 Button 96 MON BTN Assignment 2 amp 8 Button Code Item Remark 71 LCD Display Mode English Domestic Language 73 Background Music 74 Station User Name Registration 75 Headset Speakerphone Mode 76 Headset Ring Mode 80 Account Code Activation 81 DID Call Wait 83 ICM Hold BTN Assignment 84 LOOP BTN Assignment 85 Camp on Assignment 86 INTRUSION BTN Assignment System Attendant 87 UCD DND BTN Assignment Hunt Grp No UCD group should be assigned 89 Keypad Facility Key ACD STATUS BTN Assignment UCD group and ACD 97 REDIAL BTN Assignment 2 amp 8 Button DKT 98 DID Restriction 99 DISA Restriction 9 Call Recording USB 236 Not supported in ip 60 60 Issue 2 0 July 2010 LG ERICSSON 2 60
106. appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 177 Btn SMDR Save 1 When enabled On a maximum of 2000 SMDR records can be recorded in the 0 Off 0 Off Enable System memory 1 SMDR Print 2 If this parameter is On real time SDMR data outputs through the port assigned in 0 Off 0 Off Enable PGM 175 Flexible button 6 1 3 This parameter determines if All calls or only LD calls are recorded for SMDR LD 1 LD 0 All calls calls are defined by Flexible button 4 and 14 1 Long Distance Long Distance 4 This parameter determines the number of digits for a Long Distance call if the 07 07 15 Call Digit Counter number of digits exceeds the assigned value ip 60 considers the call Long Distance Flexible button 14 defines LD codes Print Incoming 5 When enabled On the system will record incoming call records for SMDR output 0 Off 0 Off Call 1 Print Lost Call 6 When enabled On lost calls are recorded for output over the assigned SMDR port O Off 0 Off Lost calls are defined as calls that are unanswered or disconnect while on Hold 1 Records in Detail 7 When enabled detailed call records are stored place of summary records A 1 On 0 Off 110 Issue 2 0 July 2010 PGM Flex Description Default Values 177 Btn maximum of 2000 detail records can be stored If
107. ast In First out FIFO First in First out 1 FIFO VMON 9 The system can be configured notify the user of new messages over an outbound 0 Disable 0 Disable telephone call 1 Enable VMON CO Grp 10 When Outbound Notification is enabled the CO Line group to use to place the 01 01 24 outbound notification call can be configured VMon Telephone 11 When Outbound Notification is enabled the telephone number to call must be 24 digits Number assigned VMON Retry 12 Should the notification fail error busy or no answer the system will retry the 2 1 9 Count outbound call up to 9 times After the number of attempts the system abandons the notification VMON Retry 13 Should the notification fail the system will attempt the call again after the 10 seconds 01 60 seconds Interval Retry Interval time Cascade 14 The system can send a copy of a received voice mail to another Voice mailbox Button 1 Station Destination Flexible button 1 Station Number Flexible Button 2 Voice Mailbox number Button 2 Voice Mailbox Number Cascade Type 15 The system will send a copy of a new message under one of several conditions as 0 No cascade 0 No Cascade Issue 2 0 56 July 2010 PGM Flex Description Default Values 129 Btn Email Notification 16 The system can be configured to send an e mail to the user as notification of a new 0 Off 0 Off voice message 1 Authorization 17 Acce
108. at are added to the user dialed number Digits None Up to 25 digits Stream A are added after the digit removal process Flexible buttons 2 amp 3 The digits are 0 9 CBack added in the number at the digit position defined under Flexible button 4 Pause DND FWD wait for dial tone Removal 2 This parameter determines the position in the user dialed number where digits are 01 01 12 Position RP removed The number of digits removed is defined under Flexible button 3 Number of digits 3 This parameter defines the number of digits to remove from the user dialed number None 01 12 to remove RN The digits are removed starting at the Removal Position defined under Flexible button 2 Add Position AP 4 This parameter defines the position in the user dialed number where the digit 01 01 13 152 Issue 2 0 July 2010 Flex Description Default Values 222 Btn CO Line Group 5 This parameter defines the CO line Group that will service LCR for this DMT index 01 01 24 The system accesses an idle CO line from the group and processes the call after digit modification Alternative DMT 6 This parameter defines an Alternate DMT index for use should a CO line not be None 00 99 index ALT available from the CO line Group assigned under Flexible button 5 153 Issue 2 0 July 2010 3 9 3 4 LCR Table Initialization PGM 223 PGM 223 permits assignment of default values for speci
109. atar 974 Saudi Arabia 966 Senegal 221 Singapore 65 South Africa 27 Spain 34 Sri Lanka 94 Swaziland 268 Sweden 46 Switzerland 41 TELKOM 27 TELSTRA 61 Thailand 66 Tunisia 216 Turkey 90 U A E 971 United Kingdom 44 Uruguay 598 Venezuela 58 Vietnam 84 967 Dial Pad Character 7 70 8 80 9 90 P 71 T 81 W 91 72 U 82 x 92 R 73 V 83 Y 93 S 74 2 94 0 oo Blank 1 2 a E 3 Issue 2 0 July 2010 Issue 2 0 July 2010 3 1 2 Board Assignment 101 PGM 101 configures the type of board installed in a slot This program is only required when a board is installed in an operational system Procedure 1 Press the TRANS PGM button 2 Dial 101 3 Dial desired slot number see Slot Number chart below 4 Select Flexible button 1 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 101 Btn Board Id 1 This parameter defines the type or function of the board installed The and See Board Id Chart Expansion boards may actually have two sub boards a station and CO board each below with a different slot number Devices for 2 This parameter displays the number of ports or channels available with the board Board and is not adjustable Board Identification Code Station ID Code CO Line ID Code Misc ID Code CHB 308 17 DSIB8 33 CSB316 13 SLIB16 33 CKB
110. atch with the user dialed digits Up to 12 digits O 9 DND any digit DMT index for 3 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 Day Zone 1 1 99 total 6 digits DMT index for 4 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 DAY Zn2 2 99 total 6 digits DMT index for 5 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 Day Zn 3 3 99 total 6 digits 150 Issue 2 0 July 2010 PGM Flex Description Default Values 221 n Check Password 6 The user may be required to enter a Station or system Authorization code in order 0 Off 0 Off for the system to process an LCR call for the LDT index 1 151 Issue 2 0 stream Flexible button 1 is added Digits are added after the removal process Flexible buttons 2 amp 3 July 2010 3 9 3 3 LCR Digit Modification Table 222 PGM 222 configures a digit modification process and a CO line Group for each of the 100 Digit Modification Table DMT entries Procedure 1 Press the TRANS button 2 Dial 222 3 Dial the DMT index 00 99 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 222 Btn Added Digit 1 This parameter defines the digits th
111. ber 04 VMIB Announce and Drop 04 VMIB Announcement number 05 System Speed 05 2000 2499 06 Internal Page 06 01 10 07 07 1 162 Code 08 Destination Destination Values All Call Page 08 1 Internal Call Page 08 2 All Call Page 09 Net Number 09 Net Number 10 Conference Room 10 1 9 11 Station Voice Mailbox 11 station number 12 Company Directory 13 Mailbox Owner Caller must enter Mailbox number 14 Record a System Greeting 15 Virtual Mailbox 163 15 mailbox number Issue 2 0 July 2010 Issue 2 0 July 2010 3 9 7 Executive Secretary Table 229 PGM 229 defines the Executive Secretary pairs Procedure 1 Press the TRANS button 2 Dial 229 3 Enterthe Table index 1 6 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 229 Btn Exec Secretary 1 This parameter assigns the Executive and Secretary pairs Not assigned Exec station Secretary station CO Call to 2 When enabled the system routes all CO line calls for the Executive to the 0 Off 0 Off Secretary Secretary station 1 Call Executive if 3 When enabled On if the Secretary is DND calls for the Executive are not routed 0 Off 0 Off Secretary DND to the Secretary even if the Executive is in DND
112. ble 8 8 8 8 8 8 8 8 19 VM MSG Wait Cancel 9 9 9 9 9 9 9 9 PGM 109 1 Reserved 2 Reserved 3 Reserved 4 Conference Room 57 57 57 57 57 57 57 57 Room Room Room Room Room Room Room Room 5 SLT Conference Page Join 58 58 58 58 5 58 58 58 6 Extend Unsupervised Conference THE THE HH HH HH THE THE THE 7 Remote Mobile Extension Control 1 1 H1 1 1 1 1 1 229 Issue 2 0 July 2010 5 QuICK REFERENCE CHARTS 5 1 Station User Program Codes Station User Program Codes Chart E Code REMARK 11 Differential Ring Keyset 12 Intercom Answer Mode 1 HF 2 3 PV Keyset 13 SMS Message Display LDP Keyset 14 Enblock Mode LDP Keyset 15 SMS Notice Display LDP Keyset 16 Scroll Speed LDP Keyset Not supported in ip 60 60 17 Ear Mic Headset LDP Keyset 18 ICM Bell LDP Keyset 19 CO Bell LDP Keyset f PTT Group 21 Station COS Down 22 Station COS Restore 23 Walking COS Keyset 24 Keyset 25 SMS INBOX Keyset 26 Delete All SMS Message Keyset 31 Authorization Code Registration 32 Authorization Code Change 230 Code ITEM REMARK
113. ble below for 07 01 11 COS COS values CO to CO Night 2 This parameter defines the CO to CO Night and Weekend COS Refer to the table 07 01 11 COS below for COS values Station COS 1 No restrictions are placed on dialing The assignments in the Exception Table A are monitored for Allow and Deny numbers CO to CO COS Table Restrictions 4A C The assignments in the Exception Table B are monitored for Allow and Deny numbers The assignments in both Exception Tables A amp B are monitored for Allow and Deny numbers The leading digit dialed cannot be a long distance code The dialed digits can be longer than 7 digits There is no restriction for the number in Canned Toll Table 91 Issue 2 0 July 2010 Station COS Restrictions 6 The leading digits cannot be a Long Distance code Only eight digits maximum can be dialed There is no restriction for the number in the Canned Toll Table 7 Intercom and paging calls are allowed No dialing allowed on CO lines ICM boxes are assigned with this COS 8 The assignments in the Exception Table C are monitored for allow and deny numbers 9 The assignments in the Exception Table D are monitored for allow and deny numbers 10 The assignments in the Exception Table C amp D are monitored for allow and deny numbers 11 The assignments in the Exception Table A B C amp D are monitored for allow and deny numbers 92 Issue 2
114. c button 8 2 External Music 3 Unused 4 8 SLT 1 5 9 Hold Tone ICM Box Music 3 This parameter assigns the music source for the Door Phone ICM Box that plays at 0 Not assigned O Not Assigned Channel the Door Phone while idle 1 Internal Music 100 Issue 2 0 July 2010 PGM Flex Description Default Values 171 Btn 2 External Music 3 unused 4 8 SLT 1 5 Assign SLT 4 This parameter assigns an SLT station in the system as an SLT source The Not assigned Flexible button SLT port requires connection to a music source SLT station number SLT 1 Flexible button 1 station number SLT 2 Flexible button 2 station number SLT MOH 3 Flexible button 3 station number SLT MOH 4 Flexible button 4 station number SLT 5 Flexible button 5 station number Dial Tone Source 5 This parameter assigns an SLT MOH source for dial tone set the SLT Station 0 Not assigned 0 Not Assign number of the SLT port 1 SLT MOH 1 2 SLT MOH 2 3 SLT 3 4 SLT 4 5 SLT 5 Intercom Ring 6 This parameter assigns an SLT MOH source for Intercom Ring Back tone 0 Not assigned 0 Not Assign Back Tone 1 SLT MOH 1 2 SLT 2 3 SLT MOH 3 4 SLT MOH 4 5 SLT 5 CO Ring Back 7 This parameter assigns an SLT MOH source for DID CO line Ring Back tone 0 Not assigned 0 Not Assign Tone RBT 1 SLT MOH 1 2 SLT 2
115. call A System Speed Dial is used to define the alternate route Destination MPB 6 This parameter defines the IP address of the receiving MPB for DECT and for the 0 0 0 0 IP v4 address IP BLF Manager support Digit Repeat 7 When enabled Yes the system will repeat digits received from the networked 0 No 0 No system for output over the outgoing PSTN connection 1 Yes Code 8 When enabled the Attendant station number associated with the CO line is 0 Off 0 Off CLI used as the CLI sent to PX Otherwise the station number placing or receiving the 1 call is used for the CLI Firewall Routing 9 When enabled On the system recognizes the connection for the Network 0 No 0 No Numbering Plan code routes through a Firewall and uses the WAN side Firewall 1 Yes address to complete the connection Authorization 10 When enabled Yes the user must enter an Authorization code The COS 0 No 0 No Code COS Use associated with the Authorization code establishes toll restriction for the call 1 Yes SMDR Hidden 11 When enabled digits dialed by the station user are NOT output in SMDR records 0 No 0 No Digits 1 Yes 185 Issue 2 0 July 2010 3 12 VOIB PGM 340 PGM 341 and PGM 500 PGM 501 3 12 1 VOIB Settings 340 PGM 340 configures IP and other characteristics of the VOIB interface Procedure 1 Press the TRANS button 2 Dial 340 3 Select the desir
116. call will disconnect when the 0 Off 0 Off Restriction Call Cut Off Timer PGM1 13 Flexible button 12 expires 1 Individual 4 If enabled the station user can access a specific CO line dialing the individual CO 1 Enable 0 Disable Line Access access code See also 107 Flexible button 8 1 Enable CO Line Queuing 5 When enabled a station user can queue for a CO line if the user receives busy 1 Enable 0 Disable tone when attempting to access the CO line 1 Enable CO PGM 6 If enabled the station user can configure Flexible buttons to access a CO line 0 Disable 0 Disable or CO line Group 1 Enable Issue 2 0 July 2010 PGM Flex Description Default Values 112 Btn Priority Line 7 When enabled On lifting the handset or pressing the On Off button answers an 1 Enable 0 Disable Answer PLA incoming call Calls are answered in the priority defined in PGM 173 1 Enable Prepaid Call 8 When enabled the station will be subject to the Prepaid Call feature If the 0 Off 0 Off station exhausts the prepaid allocation the station will be unable to place calls on a 1 CO line If the allocated funds are exhausted during a call warning tone is provided and the call is terminated after the CO Call Drop timer PGM 180 Flexible button 16 Speed Dial 9 When enabled the station can place calls employing System Speed Dial n
117. dant 047 Attendant 048 Forced Delete Conference Room Attendant 051 Pre select MSG Activation Attendant 052 Pre select MSG Deactivation Attendant 053 Custom Display Message Program 11 20 System Attendant 054 Reserved 06 Record VMIB System Greeting System Attendant 071 DND Call Forward Pre selected MSG Cancel Attendant 072 Register Station Name Attendant 073 Disable CO Outgoing System Attendant 074 Automatic Day Night Weekend Mode Program Attendant 075 ICM BOX BGM Channel select Attendant 076 077 External Page Music 1 2 and 3 toggle On Off Attendant 078 079 Prepaid Call 07 LCD Display Language 091 Set Call Forward Attendant 04 WHTU Subscription Not supported in ip 60 60 Issue 2 0 July 2010 5 3 Flexible Button Program Codes Flexible Button Program Codes Chart Code 11 Differential Ring 12 Answer Mode 1 2 T 3 3 21 Station COS Down 22 Station COS Restore 23 Walking COS 31 Authorization Code Registration 32 Authorization Code Change 41 Wake up Time Registration One time Continuous 42 Wake up Time Cancel 46 Call Coverage covered Station number 47 Mailbox button Mailbox number 48 Call Screen 1 Ring 2 Speaker 51 Pre selected MSG Activation 52 Set Custom Message 53 CLIR Key 54 Two Way Recording 55 Attend
118. ded for Norway only 1 DID Digit Receive 5 This parameter defines the number of DID digits the system expects to receive after 3 2 4 No digit removal PGM 143 Flexible button 5 DID Digit Mask 6 This parameter defines the DID digit conversion process Digit Mask for Type 0 2 to 4 digits and 2 DID Conversion PGM 143 Flexible button 4 0 9 and delete digit 73 Issue 2 0 July 2010 PGM Flex Description Default Values 146 Btn accept digit Collect Call 7 This parameter defines the type of Collect Call Blocking supported for E1 CO lines Disabled 0 Disable Blocking with R2 signaling Intended for Brazil only 1 Double Answer 2 w Indicator Collect Call 8 These parameters determine treatment of an incoming call when Collect Call 010 1 seconds 001 250 in 100 Answer Timer Blocking Double Answer is assigned In this case the system answers the call and milli seconds maintains the connection for the Call Answer time then the system will disconnect increments Collect Call Idle 9 for the Call Idle time before finally reconnecting the call 020 2 seconds 001 250 in 100 Timer milli seconds increments 74 Issue 2 0 4 Russia Auto July 2010 3 3 8 COLine Caller Id CID Attributes 147 147 defines the Caller 14 characteristics associated with analog CO lines Procedure 1 Press the TRANS PGM button 2 Dial
119. disabled Off only total calls total 1 metering count and total cost for each station are stored SMDR Dial Digit 8 This parameter defines the number of digits the system removes from the dialed 0 0 9 Hidden number recorded for SMDR Each removed digit is replaced with an in the record Digits are removed beginning from the left or right as defined in Flexible button 13 SMDR Currency 9 This parameter defines the currency unit for the call cost The currency unit can be Not Assigned 3 alpha numeric Unit up to three 3 alphanumeric characters characters SMDR Cost Per 10 This parameter defines the cost per meter pulse unit up to 6 digits Flexible button 000000 6 digits Unit Pulse 11 defines the decimal location of the cost per meter unit SMDR Fraction 11 This parameter defines the decimal location in the cost per meter unit beginning at 0 0 5 the right most digit and proceeding left to 5 digits SMDR Start 12 This parameter determines the minimum call duration of a call for SMDR If the call 000 seconds 000 250 in 1 Timer duration is shorter than the assigned time an SMDR record is not generated second increments SMDR Hidden 13 This parameter determines the order to hide SMDR dialed digits right to left Right 1 Right 0 Left Digit or left to right Left Flexible button 8 defines the number of digits to hide Hidden 1 Right digits are displayed as SMDR Long 14 This parameter defines the L
120. ed Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 321 Btn Networking 1 This parameter determines the signaling employed for call transfer over the 1 Reroute 0 7 Join Transfer Mode network The Join or Reroute method is available 1 Reroute TCP Port 2 This parameter defines the TCP port used for communications with the BLF 9000 0000 9999 Manager UDP Port 3 This parameter defines the UDP port used for communications with the BLF 9001 0000 9999 BLF Manager 4 This parameter defines the IP address of the server hosting the BLF Manager 0 0 0 0 IPv4 address Address Duration of BLF 5 This parameter sets the maximum duration between BLF status messages 02 seconds 01 20 in 1 second status increments Multicast IP 6 This parameter defines the IP multi cast address used by the BLF Manager 0 0 0 0 IPv4 address Address Net Trans Fault 7 This parameter sets the time interval the system waits for a response from a 010 seconds Recall Timer networked system when transferring a call After expiration of the timer the 001 300 in 1 second increments 181 Issue 2 0 July 2010 Description Default Values 321 Btn system will recall the transferring station GK Reroute CO 8 This parameter defines the CO line group used by a Gatekeeper when transferring 00 00 24 182 3 11 3
121. ed Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 340 Btn IP Address 1 This parameter defines the IP address for VoIP This address is assigned to the 0 0 0 0 IP v4 address Skip VOIB and if installed the VOIU Gateway Address 2 This parameter defines the IP address of the Gateway serving the VOIB 0 0 0 0 IP v4 address Skip SUBNET Mask 3 This parameter defines the Subnet mask for the VOIB IP address 255 255 255 0 IPv4 Subnet mask Skip DNS Address 4 This parameter defines the Domain Name Server the system will use to convert a 0 0 0 0 IP v4 address Skip URI to an IP address Trace Password 5 This parameter assigns a password for access to the VOIB trace facilities Not assigned Up to 10 characters see Dial Pad Character Chart 186 Issue 2 0 July 2010 PGM Flex Description Default Values 340 Btn Default Codec 6 This parameter defines the default codec that is requested in call set up messages 3 G711 u Law 0 G 723 1 1 6 729 2 711_ 3 G 711_u Law 4 729 Default Gain This parameter sets the default gain associated with audio to from the VOIB 31 01 62 No Delay TOS This parameter defines the setting for bit 3 the Delay bit of the IP TOS Type of 0 Off 0 Off Service byte When enabled low or no delay is requested 1 Throughput TOS 9 This param
122. ed Zone 232 2 1 12121 213 nennen 168 3 9 10 Weekly Time Table 233 1 12112111 1110111 169 3 9 11 Voice Mail Dialing Table 234 170 3 9 12 Mobil Extension PGM 230 aas or t log nt teet pe deed 172 3 9 13 Incoming Destination Table 237 173 3 9 14 Voice Mailbox COS Table 238 174 3 9 15 Hot Desk Attributes 250 ere xu ned xoc cd 176 3 10 SMS Attributes 291 292 22222 1 1 177 3 10 1 SMS Setting PGW 291 177 3 10 2 SMS CO Line Attributes 292 178 3 11 Private Networking 320 324 4 4 2 2222 1 179 3 11 1 Networking Basic Attributes 320 se ee 179 3 11 2 Networking Supplementary Attributes 321 181 3 11 3 Networking CO Line Attributes 322 183 3 11 4 Network Routing Network Numbering Plan Table 324 184 3 12 VOIB 340 PGM 341 and 500 PGM 501 186 3 12 1 VOIB Settings S40 oec e e eit
123. ed to send an e mail to the user as notification of a new 0 Off 0 Off voice message 1 Authorization 13 Access to a Voice Mailbox can be password protected when the user enters the Station Number 11 digits Code Password mailbox the system will request entry of the password SMTP Server 14 When e mail notification is on the SMTP Simple Mail Transfer Protocol server IP IPv4 Address address must be configured Email Address 15 When e mail notification is enabled the e mail address to notify must be configured 24 Characters 52 Issue 2 0 July 2010 PGM Flex Description Default Values 127 Btn SMTP User Id 16 When e mail notification is enabled the ip 60 60 id on the e mail server must be 24 Characters configured SMTP Password 17 When e mail notification is enabled the ip 60 60 password on the e mail server must be configured 53 24 Characters 3 2 18 Virtual Mailbox Attributes 129 PGM 129 defines Attributes for Virtual mailboxes including notification Mail access privileges and Company Directory names associated with the mailbox Procedure 1 Press the TRANS PGM button 2 Dial 129 3 Enter the Virtual Mailbox number 200 249 4 Selected desired Flexible button from the chart below 5 Enter the desired value 6 Press the Hold Save button PGM Flex Description Default Values 129 Btn Administrative 1 A mailbox can be assig
124. efines the Flexible DID Conversion route for Night mode service Not assigned 01 12 see DID Destination Chart below Weekend 4 This parameter defines the Flexible DID Conversion route for Weekend mode Not assigned 01 12 see DID Destination service Destination Chart below Lunch 5 This parameter defines the Flexible DID Conversion route for Lunch mode service Not assigned 01 12 see DID 165 Issue 2 0 July 2010 Group Attendant Flex Description Default Values 231 Btn Destination Destination Chart below Reroute 6 This parameter defines the Flexible DID Conversion route when the original Not assigned 1 5 from Destination Destination destination is busy Use codes 0 5 from the Destination Table 6 Net number Table or 7 station number for the routing to a station Voice mailbox 6 Networked station 7 station station VM 12 virtual mailbox number Tenancy Group 7 The Day Night Mode for the DID Destination Table is normally controlled by the 0 System 0 5 System Attendant When desired the Day Night mode can be controlled by a Tenant Attendant DID Destination Table Code Destination Values 01 Station 01 station number 02 Hunt Group 02 Hunt Group number 03 VMIB Announce 03 VMIB Announcement number 04 VMIB Announce and Drop 04 Announcement number 05 System Speed 05 2000 2499 06
125. efines the minimum incoming Ring on signal to be considered a 2 200 milli 2 9in 100 milli valid ring signal for Loop Ground Start T1 CO lines Shorter ring on periods are seconds second increments ignored Ring Stop Time 11 This parameter defines the maximum duration of the Ring off period to be 60 6 seconds 10 60 in 100 milli considered a valid ring signal for Loop Ground Start T1 CO lines Longer Ring off second increments signals are considered an abandoned call Collect Digit 12 not used Timer Store Timer 13 not used 78 Issue 2 0 July 2010 3 4 Board Slot Based Admin 155 3 4 4 T1 DCO Board Attributes 155 PGM 155 assigns characteristics for all digital CO lines on a T1 or E1 board Procedure 1 Press the TRANS PGM button 2 Dial 155 3 Enter the appropriate T1 DCO board slot number 4 Pressthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 155 Btn T1 R2 CRC 1 When enabled the system will perform check for T1 and R2 digital CO 0 Disable 0 Disable Check lines 1 Enable Distance 2 When the switch for selection of long loop on the board is set to Long the gain 0 0 Km 0 0 Coefficient value is set according to the Distance Coefficient Applied to LCOB SLIB HYBRID 1 3 Setting 2 5 3 7 Km DCO IP Address 3 This parameter defines the IP Address of the digital CO board
126. em will enforce Toll Restriction when a station All zones 1 On 0 Off attempts access to a Speed Dial bin in the zone 1 Authorization 4 When enabled On the system requests an Authorization code when a station Zone 1 0 Off 0 Off Check attempts access to a Speed Dial bin in the zone Others 1 On 1 168 Issue 2 0 July 2010 3 9 10 Weekly Time Table 233 PGM 233 configures separate Weekly Time Tables to control Auto Ring mode for the system and each Intercom Tenancy Group Procedure 1 Press the TRANS button 2 Dial 233 3 Dial 0 5 0 is for the system and 1 5 are for the individual Intercom Tenancy Groups 4 Select Flexible button 1 7 for Monday to Sunday respectively 5 Select the Flexible button for the desired time entry 6 Enterthe desired Time as four 4 digits 7 Pressthe Hold Save button PGM Flex Description Default Values 233 Btn 1 This parameter defines the start time for Day mode service when Auto Ring service Mon Fri 4 digits 0000 23 59 is active 09 00 Night 2 This parameter defines the start time for Night mode service when Auto Ring service Mon Thu 4 digits 0000 23 59 is active 18 00 Weekend 3 This parameter defines the start time for Weekend mode service when Auto Ring Fri 4 digits 0000 23 59 service is active 18 00 Lunch Start 4 This parameter defines the start time
127. ents VM Pause Timer 15 This parameter sets the duration of a Pause when required for an external Voice 30 3 seconds 01 90 in 100 milli Mail second increments Transit Connect 16 This parameter defines the time delay when a networked system returns a connect 04 seconds 01 30 in 1 second Timer message a system requesting use of an analog pulse dial CO line to allow the increments 120 Issue 2 0 July 2010 PGM Flex Description Default Values 181 Btn line to setup before receiving digits VMIB Message 17 This parameter determines the length of time the system will rewind a voice 03 seconds 01 99 in 1 second Rewind Timer message using the Message Rewind function in the VMIB increments LCO Connect 18 If this timer expires after starting outgoing dial the system regards the call as 00 disabled 00 30 in 1 second Timer connected At expiration any further dialed digits are ignored for the purposes of increments redial In this way digits which may be dialed into an automated service such as banking are not stored in the Last Number Redial buffer LCO CPT Detect 19 This parameter sets the duration the system periodically removes the CPT detector 05 seconds 00 20 in 1 second Timer from a CO line that is transferred or forwarded to another CO line After the increments assigned time a CPT detector is connected to the CO line to detect busy or error tone for 7 seconds The detector i
128. eter defines the setting for bit 4 the Throughput bit of the IP TOS Type 0 Normal 0 Normal of Service byte Throughput can be set to Normal or High 1 High Reliability TOS 10 This parameter defines the setting for bit 5 the Reliability bit of the IP TOS Type of 0 Normal 0 Normal Service byte Reliability can be set to Normal or High for the VOIP board reliability 1 High Firewall IP 11 This parameter defines the WAN side IP address of the NAT Firewall server 0 0 0 0 IP v4 address Address VOIB mode 12 This parameter defines the VoIP protocols required by the VOIB The system can 2 Dual 0 H 323 support SIP H 323 or both dual 1 2 SIP 2 Dual Silence Detection 13 When enabled the system will detect silence in the incoming audio and 0 Off 0 Off introduce comfort noise 1 14 When enabled the system will implement echo cancellation on audio to from 1 On 0 Off the VOIB 1 DTMF Mode 15 This parameter determines the method for interchange of DTMF signals with the call 2 In band 2 In band DTMF host DTMF S RFC2833 DTMF 4 Out band DTMF Jitter Buffer 16 This parameter determines the duration the system will store RTP packets for the 150 milliseconds 050 300 in 1 milli 187 Issue 2 0 July 2010 PGM Flex Description Default Values 340 Btn purpose of reducing jitter A short jitter buffer may result
129. ew MSN 0 Off 0 Off call to the station and the call camps on to the station 1 Long CLI1 21 If CLI Type of the CO line PGM 143 Flexible button 12 is Long CLI 1 this entry up No default Up to 16 digits 0 9 to 16 digits is sent as the CLI overriding other settings Long CLI2 22 If CLI Type of the CO line PGM 143 Flexible button 12 is Long CLI 2 this entry up No default Up to 16 digits 0 9 to 16 digits is sent as the CLI overriding other CLI settings CC Blocking 23 If this parameter is On incoming collect calls are blocked Brazil only 0 Off 0 Off 1 35 Issue 2 0 July 2010 3 2 6 Flexible Button Assignment PGM 115 PGM 115 defines the function of the DKT Flexible buttons Procedure 1 Press the TRANS PGM button 2 Dial 115 3 Enter the appropriate Station Range 4 Dial 1 to assign one of the 1 24 buttons and 2 for the 2 24 buttons 5 Select the desired Flexible button 6 Enter the appropriate Type and Range 7 Press the Hold Save button PGM Flex Description Default Value 115 Btn Flex Button All Each Flexible button of a and Console can be assigned a function See Button 01 11 Assignment value Range The Type and Range are shown in the Button Assignment Table Default Table Range see Button below Assignment Table Button Assignment Table Function Range Description Butt
130. f with a Call Coverage Flexible button for the covered station will be active The 1 covered station may also activate call coverage using Station User Program codes DND Forward to 19 When enabled calls to a station in DND forward to the station s voice mailbox 1 On 0 Off Voice Mail When using the VMIB Voice Mail a user greeting must be recorded 1 Backlight 20 Not used 32 Issue 2 0 July 2010 3 2 5 Station Attributes IV PGM 114 PGM 114 is one of four 4 program groups that assign general attributes to the station range This PGM is associated with ISDN and DID services and IP CO lines Also see PGMs 111 112 and 113 Procedure 1 Press the TRANS PGM button 2 Dial 114 3 Enter the appropriate Station Range 4 Select the desired Flexible button from the chart below 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Procedure Values 114 Btn CLIP LCD 1 If this parameter is the Calling Line Identification from the ISDN or the From 1 On 0 Off Display header of SIP lines is displayed in the station s LCD 1 COLP LCD 2 If this parameter is On the Connected Line Identification from the ISDN or the 0 Off 0 Off Display From header of SIP lines is displayed in the station s LCD 1 CLI Redirect 3 When a call is redirected by the ISDN or IP line the station will display the original 0 C
131. fic LDT and DMT parameters and initializing the entire LCR database Procedure 1 Press the TRANS button 2 Dial 223 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 223 Btn DMT for Day 1 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 Zone 1 1 see PGM 220 Entering a value changes this parameter for Day Zone 1 in the 99 total 6 digits Leading Digit Table PGM 221 DMT for Day 2 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 Zone 2 2 see PGM 220 Entering a value changes this parameter for Day Zone 2 in the 99 total 6 digits Leading Digit Table PGM 221 DMT for Day 3 This parameter defines the DMT index for each of three Time Zones in Day grouping None 3 2 digt pairs 00 Zone 3 3 see PGM 220 Entering a value changes this parameter for Day Zone 3 in the 99 total 6 digits Leading Digit Table PGM 221 CO Line Group 4 This parameter defines the default CO line for the Digit Modification Table PGM None 01 24 Change 222 Entering a value changes this parameter for all DMT entries ALT Index 5 This parameter defines the default Alternative DMT Index for the Digit Modification None 00 99 Change Table Entering a value changes this parameter for all DMT entries All LCR Data 6 This
132. for Pause Error This parameter defines the code sent to the external VM to receive an incoming Prefix P 5P 12 digits 0 9 P Index 5 Voice message when the call encounters an error Suffix and DND for Pause DND This parameter defines the code sent to the external VM to receive an incoming Prefix P 6P 12 digits 0 9 Index 6 Voice message when the call encounters DND Suffix and DND for Pause Index 7 Prefix 12 digits 0 9 170 Issue 2 0 July 2010 PGM Flex Description Default Values 234 Btn Suffix and DND for Pause Index 8 Prefix 12 digits 0 9 Suffix and DND for Pause Disconnect This parameter defines the code sent to the external VM to instruct the VM to MENS 12 digits 0 9 Index 9 disconnect and DND for Pause 171 Issue 2 0 July 2010 3 9 12 Mobil Extension PGM 236 PGM 2396 configures the characteristics of a Mobile Extension associated with each station port Procedure 1 Press the TRANS button 2 Dial 236 3 Diala table index 01 48 for a station port 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 236 Btn Allow Mobile 1 When enable the system allows the station to activate the Mobile Extension 0 Off 0 Off Extension feature 1 CO G
133. ftkey Not 114 Flexible button 5 assigned CLIP Table Index 2 This parameter defines the index to the COLP Table PGM 201 used to determine Not assigned 00 50 the CLIP sent by the system If the index is 50 the CLIP is determined from PGM Delete softkey Not 114 Flexible button 5 assigned Call Type 3 This parameter defines the call type for the ISDN CO line CLI 2 National 0 Unknown 1 International 2 National 3 Not used 4 Subscriber DID Conversion 4 This parameter defines the DID digit conversion process for DID digits received from 0 Use Digit Mask 0 Digit Mask 68 Issue 2 0 July 2010 PGM Flex Description Default Values 143 Btn the ISDN or IP CO line After removal of digits Flexible button 5 the DID number PGM 146 PGM146 treatment can be a simple conversion 0 no conversion 1 or simple conversion 1 Use digits as is with table look up 2 2 Flex DID Table PGM231 DID Remove 5 This parameter defines the number of digits to remove from the DID number 00 no digits 00 99 Number received After digit removal the ip 60 60 can process a 2 to 4 digit DID number removed Digits are removed starting with the first received digit ISDN Enblock 6 If this parameter is dialed digits are sent using Enblock Sending all digits are 0 Overlap 0 7 Overlap Sending Send sent at once user dials or Enblock timer PGM 182 Flexible bu
134. gits the user must dial for Prefix 00 00 30 code dialing Max Digits 3 This parameter defines the maximum number of digits the user must dial for Prefix 00 00 30 code dialing When the maximum digits are dialed the dialed digits are compared to the assigned code Sending 4 When enabled On the system uses Enblock sending for Prefix dialing When the 0 Off 0 Off Complete Enblock Inter digit timer PGM 182 Flexible button 10 expires or the Maximum 1 digits is reached the system sends all digits Number of Type 5 This parameter defines the Type of called number network 0 Unknown 0 Unknown 1 International 2 National 146 Issue 2 0 July 2010 PGM Flex Description Default Values 205 Btn 3 Network Spec 4 7 Subscriber 5 Abbreviated 6 Reserved Numbering Plan 6 This parameter defines the identification of the type of Numbering plan 0 Unknown 0 Unknown 1 ISDN Telephony 2 Data Numbering 3 Telex 4 National Std 5 Private 6 Reserved 147 Issue 2 0 July 2010 3 93 220 223 3 9 3 1 LCR Attributes PGM 220 PGM 220 defines the LCR access mode and time and day for each of three zones or groups for LCR access Procedure 1 Press the TRANS button 2 Dial 220 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default 220 Btn LCR
135. he CLI when an international Not assigned 4 digits 0 9 Access Code ISDN call is received Calling Sub 6 Moved to CO Line Attributes Ill PGM 146 Flexible button 4 address My Area Code 9 This parameter defines the local Area Code that is inserted as part of the Prefix code Not assigned 6 digits 0 9 when Code Insertion Flexible button 3 and 4 is enabled This value is combined with the My Area Prefix Code value for insertion My Area Prefix 10 This parameter defines the Area Prefix Code that is inserted as part of the Prefix Not assigned 4 digits 0 9 Code code when Prefix Code Insertion Flexible button 3 and 4 is enabled This value is combined with My Area Code value for insertion Maintain DID 11 When enabled the CLI is displayed in the LCD of the answering station 0 Off 0 Off Name throughout the call Otherwise the CLI is only displayed while the call is ringing 1 PC Application 12 This parameter defines the Called Party Number station number that must be 100 Station number Destination received from an ISDN to connect PC Admin to the system over an ISDN PPP Station connection 142 Issue 2 0 July 2010 3 8 2 COLP CLIP Table 201 PGM 201 assigns the CLI COL used for ISDN IP CO line calls when a Table index is assigned in PGM 143 Flexible button 1 or 2 Procedure 1 Press the TRANS button 2 Dial 201 3 Enter the desired COLP Table inde
136. he user receives dial tone recall is provided if the user hangs up 1 Flash Drop 2 Flash ignore 3 Hold Release 25 Issue 2 0 July 2010 PGM Flex Description Default Values 111 Btn 1 Flash Drop the active call is dropped 2 Flash ignore the flash is ignored no action is taken 3 Hold Release the active call is placed on hold and the user receives dial tone the held call is disconnected if the user hangs up Loop LCR 16 If this value is set to On the station user must enter an Account Code to use Loop 0 Off 0 Off Account Code LCR 1 VMIB Message 17 This parameter determines the order of Voice Mail message playback 1 FIFO 0 LIFO Type 0 LIFO Last in First out 1 FIFO 1 FIFO First in First out Off Net Call 18 When enabled On the station is permitted to activate Off Net Call Forward The 1 Disable 0 Enable Forward user can forward calls over a CO line See PGM 112 Flexible button 12 to define 1 Disable the type of calls that will forward Forced Hands 19 When enabled On the station can change the Intercom Signal mode of the called 1 0 Off Free station from Tone to Handsfree 1 Reserved 20 Reserved 21 Caller Voice Over 22 When this parameter is On the station can place calls to other stations using Voice 0 Off 0 Off Over The receiving station must be enabled to receive Voice Over PGM 113 1 Flexible button 6
137. his parameter determines if the System Time Date are set manually Off see 0 Off 0 Off Time Day Month PGM 178 or based on the Time and Date from the ISDN On 1 Off Hook Ring 2 This parameter determines if the system will use muted ring or a single ring burstfor 1 Muted ring 0 Single Burst Type the off hook ring signal 1 Muted ring Override 1 CO 3 When enabled On if the user dials 9 the system will search all CO Groups foran 1 On 0 Off Line Group idle CO line starting with the 1 Group otherwise only CO Group 1 is searched 1 Page Warning 4 When enabled On a warning tone is sent over a page prior to establishing an audio 1 On 0 Off Tone path with the paging user 1 Auto Privacy 5 If this parameter is call cannot be overridden by a station with Override 1 On 0 Off Privilege see PGM 113 Flexible button 4 1 Privacy Warning 6 If this parameter is when a call is intrude upon or overridden a warning tone is 1 On 0 Off sent to the parties on the call 1 0n Single Ring for 7 This parameter determines the cadence of CO line and Intercom ring If Yes the 0 No 0 No CO Call Intercom ring cadence is 1 second on and 4 seconds off and the CO line ring 1 Yes 84 Issue 2 0 July 2010 PGM Flex Description Default Values 161 Btn cadence is 0 45 0 25 off 0 4s on 4s off
138. ibutes PGM 191 Flex Description Default Values Ring Btn VMIB Announce 1 This parameter defines the time the system waits to automatically answer an 015 seconds 000 999 in 1 1 Timer incoming call and play the assigned VMIB announcement Flexible button 3 second increments VMIB Announce 2 This parameter defines the time the system waits after playing the first 000 seconds 000 999 in 1 2 Timer announcement to play the assigned VMIB announcement 2 Flexible button 4 to a second increments queued call 3 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 1 Location Announce 1 timer Flexible button 1 expires VMIB Announce 4 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 136 Issue 2 0 July 2010 PGM 191 Flex Description Default Values Ring Btn 2 Location announce 2 timer Flexible button 2 expires VMIB Announce 5 This parameter sets the interval between the playbacks of VMIB Announcement 2 000 seconds 000 999 in 1 2 Repeat Timer when repeating Flexible button 6 is enabled second increments VMIB Announce 6 When enabled the ip 60 will repeat the VMIB Announcement 2 Flexible 0 Off 0 Off 2 Repeat button 4 at intervals Flexible button 5 to queued calls 1 Overflow 7 When assigned calls to a station in the group queue until answered or each
139. ide CLI 0 Off 0 Off 1 70 Issue 2 0 July 2010 3 89 5 Line Ring Assignment 144 PGM 144 determines the routing for incoming calls on Normal service CO lines PGM 140 Calls are routed to and alert ring and LED the assigned destination s which can be a station range Hunt Group or a VMIB announcement Separate assignments are made for each service mode Day Night Weekend Lunch and On demand When assigned to a station the ring can be delayed by 0 to 9 seconds Procedure 1 Press the TRANS PGM button Dial 144 Enter the appropriate CO line Range Select the Flexible button for the desired service mode Day Night etc Enter the appropriate value Press the Hold Save button M E PGM Flex Description 144 Btn Day Ring Night Ring Weekend Ring Lunch Ring line while the system is in the respective service mode Calls can be routed to stations with a delay a Hunt Group a VMIB Greeting or a station in a networked system A Co ho a On demand Ring 71 Flexible buttons 1 through 5 determine call routing and alerting for calls on the CO Default Station 100 System Attendant w no delay EI 1 station range delay 0 9 2 Hunt Group 3 Greeting 00 70 4 networked station number 5 Virtual Mailbox 3 36 Line Ring Assignment Display 145 PGM 145 is used to display CO line ring assignme
140. ines parameters that affect ISDN CO line operation system wide Procedure 1 Press the TRANS button 2 Dial 200 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 200 Btn Advice of Charge 1 This parameter defines the type of Advice of Charge service provided from the ISDN 0 No AOC 0 7 no ACC service based on the country service 1 Italy amp Spain 2 Finland 3 Australia 4 Belgium 5 Standard 6 Netherlands CO ATD Code 2 This parameter defines the received DID digits that route the call to the Attendant Not assigned 2 digits 0 9 For outgoing DID calls if PGM 114 Flexible button 5 is set when station places an outgoing ISDN call this value is used for the CLI Incoming Prefix 3 Moved to CO Line Attributes Ill 146 Flexible button 1 Code Insertion 141 Issue 2 0 July 2010 PGM Flex Description Default Values 200 Btn Outgoing Prefix 4 Moved to CO Line Attributes 146 Flexible button 2 Code Insertion ISDN line 5 Moved to CO Line Attributes 146 Flexible button 3 CLI Print 6 When enabled On the system will output the received CLI over the assigned Print 0 Off 0 Off port 175 Flexible button 5 1 International 7 This parameter defines the code inserted in front of t
141. ion Flexible button 14 1 Music Source 13 This parameter determines if a queued caller receives Ringback tone or MOH 0 0 Not assigned 1 Internal Music 2 External Music 3 Not in ip 60 60 4 8 SLT MOH 9 Hold tone Alt Destination 14 This parameter assigns the Alternate destination when calls are received and no Not assigned 1 station number 132 Issue 2 0 July 2010 PGM 191 Flex Description Default Values Circular Terminal Btn members are on duty or members are busy Alternate destination routing must 2 Hunt Group be enabled see Flexible button 12 MAX Queue 15 This parameter determines the maximum number of calls that can queue to the 99 00 99 Count Group When the queued calls exceed the Maximum Queued Call Count additional calls are ignored Hunt Member 16 When enabled On a member with Call Forward active will not receive Hunt Group 1 On 0 Off forward calls the member is considered unavailable for group calls 1 Queue Count 17 When enabled On the LCD of member stations displays the Queue Call Count 1 On 0 Off Display 1 18 This parameter assigns a name maximum 12 characters to the group Not assigned 12 Characters Assign Call Coverage 19 The Call Coverage parameter enables coverage for the Hunt Group A Call Button 1 0 Off Off Coverage Flexible button at a covering sta
142. ired Station COS 00 11 5 Use Volume Up Down to navigate to next page 6 Press the Hold Save button PGM Flex Description Default Values 130 Btn Display Station 1 Displays stations by Day COS Number by COS 2 Displays stations by Night COS Issue 2 0 July 2010 3 2 20 Display Station Numbers by CO Group Access PGM 131 PGM 131 displays station numbers allowed access to a specific CO line Group Procedure Press the TRANS PGM button 1 Enter the desired CO line Group 01 24 Use Volume Up Down to navigate to next page Press the Hold Save button 2 Dial 131 3 4 5 PGM Flex 131 Btn Display Station Number by CO Group Description Displays stations by CO line Group Access Default Values 58 Issue 2 0 July 2010 3 3 CO Line PGM 140 147 3 3 1 CO Service Type 140 PGM 140 defines the type of CO line service available from the CO line Procedure 1 Press the TRANS PGM button up PIS Dial 140 Enter the CO line Range Press Flexible button 1 for CO line Type or 2 for service attributes For Line Type enter the desired Type For Normal CO line service attributes follow the instructions in the table below otherwise enter the desired value 6 Press the Hold Save button PGM 140 Line Type Normal CO line service attributes Flex Btn 1 Description This parameter defines the type of CO line
143. is parameter defines an analog CO line the system will monitor for incoming call Not assigned 01 36 Must be an transfer CO FAX Tone 1100Hz 0 5 second On 3 seconds Off repeated If detected on the CO line the call is sent to SLT port 16 in the Basic KSU Also see PGM 182 Flexible Analog CO line 85 Issue 2 0 July 2010 PGM Flex Description Default Values 161 Btn buttons 13 and 14 No DSS 18 When enable On the CO line and DSS BLF buttons at a Station do not provide 0 Disable 0 Disable ndication incoming call indications for the calls to other Stations 1 Enable UK Billing Mode 19 If this parameter is the UK Billing Mode is applied UK Only 0 Off 0 Off UK Only 1 COS 7 When 20 When enabled On if an invalid Authorization Code is entered the system changes 0 Off 0 Off Authorization Fail the Station COS to 7 fully restricted Also if the station has no Day and Night COS 1 assignment 116 the Day and Night are changed to 7 and must be reassigned to recover Otherwise the user may return to the normal COS with the COS Restore procedure 5 digit 21 This parameter determines the structure of Authorization Codes when On fixed 5 0 Off 0 Off Authorization digit Authorization Codes are used when Off variable 3 to 11 digit codes are used 1 and is the terminating digit LCR Dial Tone 22 When enabled
144. ister the user with the Call Server host Flex Description Default Values 501 Btn User ID This parameter defines the User Id that is used in the SIP From header Not assigned Max 64 characters caller call domain Id is also used the Call server in the header to see Dial Pad route calls to the user Character Chart Authentication This parameter defines the User Name employed during the registration with the SIP Not assigned Max 64 characters User Name Call server to authenticate the user see Dial Pad Character Chart Authentication This parameter defines the Password associated with the User Name and is Not assigned Max 64 characters User Password employed during registration with the SIP Call server to authenticate the user see Dial Pad Character Chart Contact Number This parameter defines the contact number used in the SIP Contact header Not assigned Max 12 characters Typically the contact number is the station or DID number associated with the see Dial Pad contact Character Chart User ID This parameter determines if the SIP User Id will register with the SIP Call serveras Provision Provision Registration defined n RFC3261 When the parameter is set to provision the User Id is not Register registered with the SIP Call server and a non RFC method must be used to route SIP calls to the system User ID Usage When enabled On the system will employ the User Id for CLI on SIP calls
145. l When the timer expires the call is abandoned and the system increments returns error tone MSG Wait 9 This parameter sets the duration between Msg Wait reminder alerts a 00 setting 00 disabled 00 60 in 1 minute Reminder Tone disables the reminder tone increments Timer Paging Timeout 10 This parameter sets the duration of a Page When the time expires the Page 015 seconds 000 255 in 1 Timer disconnects and returns the Internal External Page Zone to idle A setting of O00 second increments disables the timer Pause Timer 11 This parameter sets the time the ip 60 waits before sending digits on a CO line 3 seconds 1 9in 1 second when a Pause is encounter in a Speed Dial number The Pause Time is also used increments for LNR and other automatic dialing Preset Call 12 This parameter sets the duration CO Line calls signal the assigned station before 25 seconds 00 99 in 1 second Forward Timer reroute to the Preset Forward destination see PGM 121 increments SLT DTMF 13 This parameter sets the duration that a DTMF receiver is connected to the SLT port 00 disabled 00 60 in 1 second Release Timer When set to 0 the DTMF receiver will release if no digits are dialed for the inter digit increments time button 8 remains connected for the duration of the call 3 SOFT Auto 14 This parameter determines the duration a Softkey menu is displayed before returning 05 seconds 01 30 in 1 second Release Timer to the idle menu increm
146. lan C STATION BASE 110 station ID 1 1 Station Attribute 1 112 Station Attribute 113 Station Attribute 114 Station Attribute IV 115 Flex Button Assignment 116 Station COS 117 CO Line Group Access 118 Internal Page Zone 119 Conference Page Zone 221 CO BASE PGM 120 Item ICM Tenancy Group 121 Preset Call Forward 122 Line Selection 124 SMDR Account Group 125 Copy DSS Button 126 Station IP List 127 Station Voice Mailbox Attributes 129 Virtual Voice Mailbox Attributes 131 Display Stations by CO Line Group Access 130 Display Stations by COS 140 Service Type 141 CO Line Attribute 142 Line Attribute II 143 SDN CO Line Attribute 1 144 CO Ring Assignment 145 CO Ring Assignment Display 146 CO Line Attribute 147 CID Attribute 152 1 CO Line Attributes T1 Lines SLOT BASE SYSTEM BASE 155 Attribute 160 5 Attribute 161 System Attribute 162 ADMIN Password 163 Alarm Attributes Attendant Assignment 222 Issue 2 0 July 2010 Item 165 Attendant VMIB Announcements 166 CO to CO COS 767 DID DISA Destination 168__ Control Contact 169
147. le button 4 Enterthe appropriate slot number 5 Press the Hold Save button PGM 103 Flex Btn Description Default Values CO line Board 1 This parameter defines the logical order of the CO line slots 05 08 Station Board 2 This parameter defines the logical order of the Station slots 01 04 amp 99 Voice Mail 3 This parameter defines the logical slot number for the Voice Mail AA boards 09 Interface Board 10 Issue 2 0 July 2010 3 1 4 Numbering Plan 104 PGM 104 defines the basic Numbering Plan for the system Eight choices are available as shown in section 4 2 Procedure Press the TRANS PGM button 2 Dial 104 3 Enter the appropriate value 4 Press the Hold Save button 104 Btn This parameter defines the basic Numbering Plan for the system One of eight basic 1 1 8 plans can be used as shown in section 4 2 System Numbering Plan 11 Issue 2 0 July 2010 3 1 5 Flexible Station Numbering Plan PGM 105 PGM 105 assigns station intercom numbers to each station port Two methods are available Individual Station assignment or Station Range assignment When changing to a two 2 digit Station Numbering Plan delete the existing numbering press the Speed button then enter the new two 2 digit numbering Also assure that the new Station Numbering Plan does not conflict with other Numbering Plan codes Individual Station assignment Procedure
148. ly toggles the value On or Off In certain PGMs e g a Station CO line PGM group the desired station or CO line range is required Once the parameter is selected the LCD will indicate the parameter value for the first station or CO line in the range Entering a single station or CO line number for both the upper and lower end of the range will change the parameter for the station or CO line number entered 2 2 4 Resetting the System When certain parameter values are changed the system must be reset to reorganize memory Parameters that require a reset after being changed include PGM 100 Location 101 Board Assignment PGM 103 Logical Slot Assignment 108 IP Settings PGM 380 VOIB Slot Assignment RSG IP Phone 381 RSG IP Phone Ports Assignment Issue 2 0 July 2010 When a reset is required PGM 450 Flexible button 15 may be used to reset the system without the need to turn power Off and On or opening the KSU to access the reset button To reset the system while in the Program mode 1 Press the TRANS PGM button 2 Dial 450 3 Press Flexible button 15 4 Press the SAVE softkey the system will reset 2 2 5 Initial Set up The initial set up of the ip 60 as discussed in the Hardware Description and Installation Manual requires proper configuration of the Basic Set up Programs This group of programs includes 100 to PGM 109 PGM 100 defines the Nation Code
149. mbering Plan index 00 70 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 324 Btn System Usage 1 This parameter defines the type of connection for the Numbering Plan code 0 Network 0 Network Network setting is used when the connection is between networked systems 1 PSTN otherwise use PSTN Net Numbering 2 This parameter defines the individual Network Numbering Plan code digits For a Not assigned 16 digits 0 9 and Code local station number enter after the first digit to signify a local station 1 signifies local asterisk is used to signify any digit 9 station numbers any digit wild card Net Number CO 3 This parameter defines the Network CO line group used to set up the connection for Not assigned 00 24 Line Group the Network Numbering Plan code A 00 value is used to denote a local intercom connection CPN IP 4 This parameter defines the IP address of the destination system s VOIB Only 0 0 0 0 Flexible button 1 4 Information Flexible button 1 is used for the ip 60 60 to define the VOIB IP address IP v4 address 184 Issue 2 0 July 2010 PGM Flex Description Default Values 324 Btn Alternate Dial Bin 5 This parameter defines the alternate route when a network fault occurs while Not assigned 2000 2499 attempting to route a networked
150. member stations displays the Queue Call Count 1 On 0 Off Display 1 15 This parameter assigns a name maximum 12 characters to the group Not assigned 12 Characters Assign Call Coverage 16 The Call Coverage parameter enables coverage for the Hunt Group A Call Button 1 0 Off Off Coverage Flexible button at a covering station for the group will be active The 1 covering station must a Coverage button set using Station User Program codes Button 2 0 0 9 cycles 46 and group number Flexible button 1 Hunt Coverage Mode On Off Flexible button 2 Delay Ring Cycle 3 7 2 4 VM Group Attributes PGM 191 Flex Description Default Values External VM Btn 1 This parameter sets the duration a station remains unavailable after completing 002 seconds 000 999 in 1 call second increments Put Mail Index 2 This parameter defines the index in the Voice Mail dialing table for the Put mail code 1 1 4 Get Mail Index 3 This parameter defines the index in the Voice Mail dialing table for the Get mail 2 1 4 code Hunt Type 4 This parameter defines the type of Hunt Group Circular or Terminal for the VM 0 Terminal 1 Circular group 2 Terminal 138 Issue 2 0 July 2010 PGM 191 Flex Description Default Values External VM Btn SMDI Port 5 Not available in the ip 60 60 Overflow Timer 6 This parameter sets the interval a call will queue
151. n Enter the appropriate value Press the Hold Save button Circular amp Terminal Hunt Group Attributes Flex Circular Terminal Btn VMIB Announce 1 1 Timer Description This parameter defines the time the system waits to automatically answer an incoming call and play the assigned VMIB announcement Flexible button 3 Default 015 seconds Values 000 999 in 1 second increments VMIB Announce 2 2 Timer This parameter defines the time the system waits after playing the first announcement to play the assigned VMIB announcement 2 Flexible button 4 to a queued call 000 seconds 000 999 in 1 second increments VMIB Announce 3 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 1 Announce 1 timer Flexible button 1 expires VMIB Announce 4 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 2 Location announce 2 timer Flexible button 2 expires VMIB Announce 5 This parameter sets the interval between the playbacks of VMIB Announcement 2 000 seconds 000 999 in 1 2 Repeat Timer when repeating Flexible button 6 is enabled second increments VMIB Announce 6 When enabled the ip 60 will repeat the VMIB Announcement 2 Flexible 0 Off 0 Off 2 Repeat button 4 at intervals Flexible button 5 to queued calls 1 131 Issue 2 0
152. n of the alerting cycle second increments for the incoming call CO Ring On 21 This parameter sets the minimum Ring on signal duration the system will detect as 2 200 milli 1 9 100 milli Timer an incoming CO call The ip 60 considers shorter periods a spurious signal seconds second increments CO Warning 22 This parameter sets the amount of time before receiving a warning tone as a 180 seconds 060 900 in 1 Tone Timer reminder of the elapsed call time on an outgoing CO line conversation Intended for second increments Korea only Reserved 23 2 Call Alert 24 When a busy SLT receives a 279 call the station receives a call waiting tone a Timer intervals of the 2 Call Alert timer 118 Issue 2 0 July 2010 3 5 21 2 System Timers Il PGM 181 PGM 181 is one of three PGMs used to define timers that affect system wide operations See also PGM 180 and 182 Procedure 1 Press the TRANS button 2 Dial 181 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 181 Btn Call Forward No 1 This parameter sets the No answer Forward time if No answer Call Forward is 015 seconds 000 255 in 1 Answer Timer active at the station when the timer expires the call is rerouted to the designated second increments destination DID DISA No 2 This parameter sets the time a DID DISA call will ring the station before it is
153. n the assigned DID Table entry SIP User Id Table 5 This parameter identifies the SIP User Id to route for this MSN index The User 00 00 32 Index Id is provided in the To header of the SIP message When the received SIP User Id matches this SIP User Id Table entry the call is routed based on the assigned DID Table entry Flexible button 2 144 Issue 2 0 July 2010 3 9 Tables PGM 204 205 and 220 238 amp 250 3 9 1 Local Code Table PGM 204 PGM 204 defines leading digits that are considered local calls for SMDR and toll restriction Procedure 1 Press the TRANS button 2 Dial 204 3 Enter Table index 01 to 16 4 Enterthe desired Local code up to 5 digits 0 9 5 Press the Hold Save button 145 3 9 2 Enblock Prefix Table PGM 205 PGM 205 configures characteristics for Prefix code dialing Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial205 3 Select the desired Flexible button 4 Enter the table index 01 50 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 205 Btn Prefix code 1 This parameter defines the Prefix code number to match to the user dialed digits Not assigned 8 digits 0 9 and the dialed number matches an assigned Prefix code the number is dialed DND for any digit Min Digits 2 This parameter defines the minimum number of di
154. n the caller to the previous announcement 1 Previous VM ON 5 The system can be configured to notify the user of new messages by placing an 0 Disable 0 Disable Outbound outbound telephone call 1 Enable Notification 51 Issue 2 0 July 2010 PGM Flex Description Default Values 127 Btn VMON CO Grp 6 When Outbound Notification is enabled the CO Line group to use to place the 01 01 24 outbound notification call be configured VMON 7 When Outbound Notification is enabled the telephone number to call must be 24 digits Telephone assigned Number VMON Retry 8 Should the notification fail error busy or no answer the system will retry the 2 1 9 Count outbound call up to 9 times After the assigned number of attempts the system abandons the notification VMON Retry 9 Should the notification fail the system will attempt the call again after the 10 seconds 01 60 seconds Interval Retry Interval time Cascade 10 The system can send a copy of a received voice mail to another Voice mailbox Button 1 Station Destination Flexible button 1 Station Number Flexible Button 2 Voice Mailbox number Button 2 Voice Mailbox Number Cascade Type 11 The system will send a copy of a new message under one of several conditions as 0 no cascade 0 No Cascade assigned here 1 Immediate 2 Notify Failure 3 Urgent Email Notification 12 The system can be configur
155. ned to allow access to other mailboxes and other 0 Disable 0 Disable Mailbox administrative functions 1 Enable VMIB access 2 The VMIB Access parameter enables the Virtual Voice Mailbox to receive calls 0 Disable 0 Disable 1 Enable Class of Service 3 Each mailbox can be assigned a COS to define specific characteristics of the 1 1 5 mailbox including message storage limitations and message delivery options refer to PGM 238 Announce Only 4 A mailbox can be configured to provide an announcement only and will not provide 0 Disable 0 Disable incoming message storage 1 Enable Action after 5 When configured as an Announcement Only mailbox the system will either 0 hang up 0 Hang up Announcement disconnect the call or return the caller to the previous announcement 1 Previous 54 Issue 2 0 July 2010 assigned here 55 1 Immediate 2 Notify Failure 3 Urgent PGM Flex Description Default Values 129 Btn VMIB Message 6 The Voice Mailbox may require entry of a valid system password for access to the 0 Off 0 Off Password mailbox 1 VMIB Message 7 If this parameter is set to On the VMIB will play the Date and Time stamp for each 0 Off 0 Off Time message before playing the message 1 VMIB Message 8 This parameter defines the order in which messages are retrieved from the Voice 0 LIFO 0 LIFO Mailbox LIFO L
156. nfigure SIP operation see also 501 Procedure 1 PC Admin only PGM Flex Description Default Values 500 Btn Proxy Server This parameter defines the IP address or URI for the SIP proxy server Not assigned Max 32 digits Address character string e g abcd efg see Dial Pad Character chart Proxy Server Port This parameter defines the port used for SIP messages to from the SIP Proxy 5060 0000 9999 server Proxy This parameter defines the valid registration interval the system will request when 3600 seconds 0 65535 sec Registration registering with a SIP Call server Timer Use Outbound When enabled On the system sends SIP signaling messages to the SIP Proxy On Off Proxy otherwise messages are sent to the Call server On Primary DNS This parameter defines the primary Domain Name Server the ip 60 will use to Not assigned IPv4 address Address convert a URI to an IP address Secondary DNS This parameter defines the secondary Domain Name Server the ip 60 will use to Not assigned IPv4 address Address convert a URI to an IP address if the primary DNS does not respond Domain This parameter defines the domain name or IP address used by the system in To Not assigned Value Max 32 digits and From SIP messages when a separate SIP User id is not defined See also PGM 111 Flexible button 23 and PGM 501 character string e g domain name com This parameter defines the transport mode for
157. nts defined in PGM 144 Procedure 1 Press the TRANS PGM button 2 Dial 145 3 Enter the appropriate CO line Range 4 Selectthe Flexible button for the desired service mode Day Night etc 5 Use the Volume Up Down buttons to navigate to next previous page 72 Issue 2 0 July 2010 Issue 2 0 July 2010 3 37 CO Line Attributes 146 Program 146 is one of three PGMs that assign general attributes to the CO line range Also see PGMs 141 and 142 Procedure 1 Press the TRANS PGM button 2 Dial 146 3 Enter the appropriate CO line Range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 146 Btn Incoming Prefix 1 When enabled On the My Area and Prefix codes PGM 200 Flexible buttons 9 0 Off 0 Off Code Insertion amp 10 are inserted in front of received CLI for incoming calls 1 Outgoing Prefix 2 When enabled On the My Area and Prefix codes PGM 200 Flexible buttons 9 amp 0 Off 0 Off Code Insertion 10 are inserted in front of the CLI for outgoing calls 1 ISDN Line Type 3 This parameter determines the codec used by the ISDN or IP line The codec can 1 u Law 0 A Law be PCM u Law NA standard or A Law EU standard 1 yu Law Calling Sub 4 When enabled On the bit for the calling party sub address in the ISDN Setup 0 Off 0 Off address message is set for outgoing calls Inten
158. o 4 digit numbers Dial 4 Ring 4 0770 0000 Two 4 digit numbers PGM Flex Description Default Values 423 ACNR Btn Cadence 100 000 255 20 milli Dial 1 ACNR Ring Back Tone 200 Off second increments Dial 2 025 On 000 255 in 20 milli ACNR Busy Tone 025 Off second increments Dial 3 012 On 000 255 in 20 milli ACNR Error Tone 012 Off second increments Dial 4 1500 0 255 in 20 milli 7 ACNR S Dial Tone 2 99 000 Off second increments PGM Flex Description Default Values 424 DTIB ACO Btn Rx Gain 1 Short ACO Intended for SAF only 37 00 63 2 Long ACO Intended for SAF only 42 00 63 215 Issue 2 0 July 2010 3 15 Initialization PGM 450 450 is used to initialize all or sections of the ip 60 database and can be used activate a software reset of the system After selecting the data to initialize the system must be reset use either Flexible button 15 the system reset switch or power cycling Procedure 1 Press the TRANS button 2 Dial 450 3 Selectthe desired Flexible button for the data to initialize 4 Select Flexible button 15 to reset the system and initialize the selected data 5 Press the Hold Save button to initialize the database selected PGM Flex Description Default Values 450 Btn Flexible 1 Initializes PGM105 PGM106 amp PGM107 Numbering Plan Station Database 2 Initializes PGM110 114 116
159. on Type No Undefined Undefined User programmable 2 _ CO line xx 01 36 CO line H 4 CO line Group xxj 01 24 CO line Group 36 LOOP Function Range Description Virtual Voice Mailbox Type i 5 Station 100 147 DSS for Station xxxx 6 Station User PGM 11 99 See Station User PGM chart in section 4 1 Code 7 Station Speed xxx 000 099 Station Speed Bin 8 System Speed xxxx 2000 2499 System Speed 9 Number Plan Number Plan Code Numbering Plan Code 106 107 amp 109 10 Net DSS DSS for networked station 11 MSN MSN No Not available in ip 60 60 12 200 249 Virtual Mailbox number Button Default Configuration Flexible DKT Model Button 12 Button 24 Button 1 DND FWD CO 1 2 LOOP CO 2 3 Not assigned CO 3 Not assigned CO 4 4 5 Not assigned CO 5 6 Call Back CO 6 7 LOOP CO 7 8 Notassigned_ CO 8 9 Not assigned LOOP 10 Not assigned Not assigned 37 Issue 2 0 July 2010 Issue 2 0 July 2010 Flexible DKT Model 12 Button 24 Button 11 Not assigned Not assigned 12 24 Not assigned For 12 button phones the first button is fixed as a Speed Dial button and buttons 2 to 12 renumbered as buttons 1 to 11 38 Issue 2
160. on code index in place of the actual Authorization code 1 112 Issue 2 0 July 2010 Blank 1 2 113 Issue 2 0 July 2010 3 5 19 System Time and Date 178 PGM 178 sets the system Time and Date Procedure 1 Press the TRANS button Flexible button 1 DST End Month 00 12 Flexible button 2 DST End Week 00 06 Flexible button 3 DST End Day 00 07 Flexible button 4 DST End Time 00 24 End Week 1 End Day 07 End Time 02 2 Dial 178 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 178 Btn Time 1 This parameter sets the current system Time 00 00 4 digit 2 This parameter sets the current Date for the system 01 01 05 MM DD YY DST 3 The system can support automatic Daylight Savings Time DST adjustment of the 0 Off 0 Off system clock 1 Set DST Start 4 For DST the start time for DST can be configured Start Month 3 Flexible button 1 DST Start Month 00 12 Start Week 2 Flexible button 2 DST Start Week 00 06 Start Day 07 Flexible button 3 DST Start Day 00 07 Start Time 02 Flexible button 4 DST Start Time 00 24 Set DST End 5 For DST the end time for DST can be configured End Month 11 114 Issue 2 0 July 2010 3 5 20 Linked Station Pairs PGM 179 PGM
161. ong Distance LD call codes when dialed as the first Flexible btn 1 1 Flexible button1 5 Distance Codes digits these codes indicate a Long distance call When an LD code is dialed an Flexible btn 2 5 Up to 2 digits each SMDR call record is generated Five LD codes each up to 2 digits can be defined Not assigned MSN Print on 15 If this parameter is On the MSN number is output as the station number in the 0 Off 0 Off SMDR SMDR record 1 Print Caller 16 When enabled On the SMDR record for incoming calls will include the Caller Id 0 Off 0 Off Number 1 Intercom SMDR 17 When enabled Intercom call data is stored for output as part of the Off line 0 Off 0 Off Save SMDR output 1 111 Issue 2 0 July 2010 PGM Flex Description Default Values 177 Btn Intercom SMDR 18 When enabled On Intercom call data is output as part of the On line SMDR output O Off 0 Off Print 1 SMDR Interface 19 When enabled the system will output SMDR data only upon request of an 0 Off 0 Off service external software application 1 I SMDR 20 This parameter assigns the connection between the system and the external 0 Serial 0 Serial connection type application Serial RS 232 or LAN 1 LAN I SMDR Author 21 When enabled On SMDR records sent to the external application software will 0 Off 0 Off Index include the Authorizati
162. operation 141 Flexible button 5 Transfer Tone 15 This parameter determines if a call receives Ring Back tone or MOH during a 0 Ring Back 0 7 Ring Back Tone transfer 1 MOH CO to CO Xfer 16 See PGM 142 Flexible button 18 CPT detection 82 Issue 2 0 July 2010 PGM Flex Description Default Values 160 Btn ACD Package 17 not used 0 Off 0 Off Usage 1 18 If this parameter is Unsupervised Conference member extend the 0 Off 0 Off Unsupervised duration of the conference by dialing the UC Timer Extend code Also see PGM 1 Conference 182 Flexible button 6 for the UC Conference Timer Extend Timer Call Log List 19 This parameter determines the number of records allowed for the Call Log at each 15 15 50 Number station The system allocates memory for the Call Logs until the Call Log memory is exhausted Reserved 20 SIP Pound 21 When enabled and are treated as dialed digits a SIP outgoing call 0 Off 0 Off Usage 1 83 3 5 2 System Attributes Il 161 PGM 161 defines general system attributes Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 161 3 Press the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 161 Btn 1 T
163. parameter sets the duration of ringback tone before an ACNR attempt 30 seconds 01 50 in 1 second Answer Timer terminates the call disconnects and the retry counter increments increments ACNR Pause 10 This parameter sets the time between ACNR attempts at expiration the ip 60 030 seconds 005 to 300 in 1 Timer attempts ACNR second increments ACNR Retry 11 This parameter determines the number of attempts the system will make for a given 03 01 30 Counter ACNR request After the assigned number of attempts ip 60 cancels the ACNR request ACNR No Tone 12 This parameter determines the maximum number of times ACNR attempts to secure 1 1 9 Retry Counter a CO line If a CO line is not seized all lines busy or out of service ip 60 cancels the ACNR request ACNR Tone 13 This parameter sets the duration the system will monitor the CO line for valid call 030 seconds 000 300 in 1 Detect Timer progress tones If ip 60 detects busy or reorder tone or the timer expires the second increments attempt terminates the CO line disconnects and the retry counter increments Automatic CO 14 This parameter sets the duration the system will wait for a user to dial on an outgoing 030 seconds 020 300 in 1 Release Timer CO line call If the timer expires the call attempt terminates and the station receives second increments error tone CCR Inter digit 15 This parameter sets the duration the system will wait between dialed digits for a CCR 030 3 seconds 000
164. r 28 Issue 2 0 July 2010 PGM Flex Description Default Values 112 Btn MSG Scroll 17 For Korea only this parameter defines the speed at which SMS and broadcast 0 Fast 0 to 7 0 fastest and Speed notices scroll across the LCD of the station 7 slowest Block Back Call 18 When enabled if an SLT busy on a CO line call hook flashes and places 0 Off 0 Off another CO line call the system will automatically terminate the original CO line call 1 This disables Broker and assures the SLT user cannot establish an Unsupervised Conference Incoming call 19 When enabled On the duration of an incoming CO line call is limited to the CO Call 0 Off 0 Off Time Restriction Restriction Time PGM 181 Flexible button 17 the call will disconnect when the 1 timer expires Forced Station 20 If this parameter is enabled On the station user must enter an Authorization code to 0 Off 0 Off Account Code place an outgoing CO call 1 Reserved 21 Door Open 22 If this parameter is enabled the station can activate a Door Open contact with the 0 Disable 0 Disable Door Open code Contacts are defined in PGM 168 1 Enable Dummy Station 23 If this parameter is On the station will provide Hot Desk service any agent 0 Off 0 Off login and employ the station normally 1 24 If this parameter is
165. r Bluetooth Not supported in ip 60 60 4 Bluetooth Usage Not supported in ip 60 60 232 5 2 Attendant User Program Codes Attendant User Program Codes Chart __ Code ITEM REMARK 0111 Print SMDR Station Base System Attendant 0112 Delete SMDR Station Base System Attendant 0113 Print SMDR Group Base System Attendant 0114 Delete SMDR Group Base System Attendant 0115 Display Call Charge System Attendant 0116 Abort Printing System Attendant 0117 Print Lost Call System Attendant 0118 Delete Lost Call System Attendant 0121 Print All Summary System Attendant 0122 Print All Periodically System Attendant 0123 Abort Periodic Printing System Attendant 0124 Print ATD Traffic System Attendant 0125 Print Call Summary System Attendant 0126 Print All Hourly System Attendant 0127 Print H W Usage System Attendant 0128 Print CO Summary System Attendant 0129 Print CO Hourly System Attendant 021 Set ICM Only Mode Attendant 022 Restore COS Attendant 031 Change Authorization System Attendant 041 Change Date Time Attendant 042 Set Wake up Attendant 233 Issue 2 0 July 2010 234 __ Code ITEM REMARK 043 Disable Wake Up System Attendant 044 LCD Date Mode Change System Attendant 045 LCD Time Mode Change System Attendant 046 Use PX Network Time amp Date System Atten
166. roup 2 This parameter assigns the CO line group to use when the system calls the Mobile 01 01 24 Extension An ISDN or IP CO line group must be used Telephone Number 3 This parameter assigns the number the system dials to call the Mobile Extension Not assigned Up to 24 digits CLI Number 4 This parameter assigns the CLI the system receives for an incoming call from the Not Assigned Up to 16 digits Mobile Extension Mobile Extension 5 When enabled On Hunt group calls to the associated station alert to the Mobile 0 Off 0 Off Hunt Call Extension 1 Voice Message 6 When enable the system sends an SMS to the Mobile when a voice mail is 0 Off 0 Off Notification received for the associated station PSTN SMS must be available 1 Mobile Extension 7 When enabled the Mobile Extension feature is activated This is the same as O Off 0 Off Usage the user dialing 34 to Activate Mobile Extension 1 Issue 2 0 July 2010 3 9 13 Incoming CLID Destination Table PGM 237 PGM 237 defines the destination for DID calls when the CLI matches one of up to 100 CLI entries Procedure 1 Press the TRANS button 2 Dial 237 3 Enterthe ICLID Table index 001 100 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 237 Btn Incoming CLI 1 This parameter assigns a CLI that if matched with the
167. s If the call is not second increments answered in the Virtual Answer time the call is disconnected form the system Intended for use in Russia only RCID Digit 7 This parameter defines the number of digits of the received CID to display 07 04 10 Number Intended for use in Russia only RCID Request 8 This parameter determines the number of times the system will request CID from the 1 1 3 network when Request is to Auto The maximum value is 3 Intended for use in Russia only RCID Request 9 This parameter determines the time the system will wait between RCID Requests 10 100 milli 10 30 in 10 milli Delay Intended for use in Russia only seconds second increments 76 3 3 9 T1 CO Line Attributes 152 PGM 152 defines various attributes associated with T1 CO lines Procedure 1 Press the TRANS PGM button Issue 2 0 July 2010 2 Dial 152 3 Enter the appropriate CO Line Range 4 Pressthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 152 Btn Pause Duration 1 This parameter sets the duration of the delay in dialing when a pause is encountered 2 seconds 1 1 in a Speed Dial number increments Release Guard 2 This parameter defines the interval between when a user disconnects from a T1 CO 20 2 seconds 01 60 100 milli Time line call and when the CO
168. s then removed from the line and reconnected at expiration of the timer This process continues until the connection is terminated This timer applies to Busy Error CPT in PGM 142 Flexible button 18 Forward To VMIB 20 This parameter sets the duration a station receives ring before the call forwards to 20 seconds 01 60 in 1 second Timer the VMIB when Auto Forward To VMIB PGM113 Flexible button 14 is enabled 121 increments Issue 2 0 July 2010 3 5 21 3 System Timers 182 PGM 182 is one of three PGMs used to define timers that affect system wide operations See also PGM 180 and 181 Procedure 1 Press the TRANS button 2 Dial 182 3 Select the desired Flexible button 4 Enterthe appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 182 Btn SLT Hook Switch 1 This parameter defines the duration of a hook switch transition considered a 01 100 milli 01 25 in 100 milli Bounce Timer spurious signal and ignored If the signal is stable for a period longer than the seconds second increments bounce time it is considered a valid hook switch transition SLT Maximum 2 This parameter sets the maximum duration of a Flash new dial tone request from 075 750 milli 001 250 in 10 milli Hook Flash Timer an SLT An open hook switch signal longer than the maximum is considered a seconds second increments disconnect signal from the SLT SLT
169. scription Default Values 402 DTIB Spkr Btn Gain 1 DTIB DTIB 30 00 63 2 DTIB SLIB 39 00 63 3 Reserved 4 DTIB WTIB 26 00 63 5 DTIB ACOB 22 00 63 6 Reserved 7 DTIB DCOB 33 00 63 207 Issue 2 0 July 2010 Flex Description Default Values 402 DTIB Spkr Btn Gain 8 DTIB VMIB 29 00 63 9 DTIB DTMF 08 00 63 10 DTIB TONE 22 00 63 11 DTIB MUSIC1 29 00 63 12 DTIB MUSIC2 29 00 63 13 Reserved PGM Flex Description Default Values 403 WTIB Gain Btn 1 WTIB DTIB 26 00 63 2 WTIB SLIB 33 00 63 3 Reserved 4 WTIB WTIB 26 00 63 5 WTIB ACO 38 00 63 6 Reserved 7 WTIB DCO 33 00 63 8 WTIB VMIB 29 00 63 9 WTIB DTMF 08 00 63 10 WTIB TONE 37 00 63 11 WTIB MUSIC1 29 00 63 12 WTIB MUSIC2 29 00 63 13 Reserved 208 Issue 2 0 July 2010 Flex Description Default Values 404 ACOB Gain Btn 1 ACOB DTIB 22 00 63 2 ACOBB SLIB 32 00 63 3 Reserved 4 ACOB WTIB 31 00 63 5 ACOB ACOB 36 00 63 6 Reserved 7 ACOB DCO 38 00 63 8 ACOB VMIB 37 00 63 9 ACOB DTMF 36 00 63 10 ACOB TONE 37 00 63 11 ACOB MUSIC1 37 00 63 12 ACOB MUSIC2 37 00 63 13 Reserved 14 ACO Modem 37 00 63 PGM Flex Description Default Values 406 DCOB Gain Btn 1 DCOB DTIB 26 00 63 2
170. see the PC Admin User Manual 2 1 Program Groups Various related parameters are divided into groups called Programs PGMs Each PGM group is further grouped into sections of related PGMs for example parameters related to LCR are all located in the LCR PGM groups and timers for system operation are located in the System Timers PGMs Each PGM is identified with a 3 digit code dialed from the DKT dial pad to access the PGM parameters The Admin Program List is shown in section 4 1 Admin Program Code Index Note that PGMs 500 and 501 are only accessible using the ip 60 PC Admin 2 2 Digital Key Telephone Admin For Admin Programming from a DKT an LDP 6230D connected to a station port allowed Admin access default station 100 must be used While in the Program Mode the DKT acts as a programming terminal and cannot be used as a phone In the Program Mode the LCD displays menu items and parameters with assigned values The dial pad is used to enter a PGM group and generally Flexible buttons select individual parameters from the group The dial pad is then used to input a desired value for the parameter Other buttons and softkeys on the DKT provide special Program functions 2 2 1 Entering the mode To enter the Program mode from a DKT 1 Press the TRANS PGM button 2 Dial and If assigned the display requests entry of the Admin Password 3 Enterthe Admin Password Issue 2 0 July 2010 At this point
171. ss to a Voice Mailbox can be password protected when the user enters the Mailbox Number 11 digits Code Password mailbox the system will request entry of the password SMTP Server 18 When e mail notification is on the SMTP Simple Mail Transfer Protocol server IP IPv4 Address address must be configured Email Address 19 When e mail notification is enabled the e mail address to notify must be configured 24 Characters SMTP User Id 20 When e mail notification is enabled the ip 60 60 id on the e mail server must be 24 Characters configured SMTP Password 21 When e mail notification is enabled the ip 60 60 password on the e mail server 24 Characters must be configured Company 22 For Access from the company directory the virtual mailbox must be assigned a First 12 Characters Directory First Name A recorded Name greeting and Last Name are also required Use two digits Name for each character as shown in the Dial Pad Character Chart below Company 23 For Access from the company directory the virtual mailbox must be assigned a Last 12 Characters Directory Last Name Use two digits for each character as shown in the Dial Pad Character Chart Name below Issue 2 0 July 2010 3 2 19 Display Station Numbers by COS PGM 130 PGM 130 displays station numbers assigned a specific Station COS Procedure 1 Press the TRANS PGM button 2 Dial 130 3 Press Flexible button 1 for Day COS or Press Flexible button 2 for Night COS Enter the des
172. ssigned 156 Values Table entry number 01 to 30 Allow Deny number 0 9 3E and DND as any digit wild card entry maximum 14 digits Flex Description Default 224 Btn used in Station COS 8 10 and 11 Deny Table C 6 This parameter selects a Table index and denied digit strings for the Deny Table C Not assigned used in Station COS 8 10 and 11 Allow Table D 7 This parameter selects a Table index and allowed digit strings for the Allow Table D Not assigned used in Station COS 9 10 and 11 Deny Table D 8 This parameter selects a Table index and denied digit strings for the Deny Table D Not assigned used in Station COS 9 10 and 11 157 Values Issue 2 0 July 2010 Issue 2 0 July 2010 3 9 4 2 Canned Toll Tables 225 PGM 225 defines the Allow and Deny Table used to determine Class of Service 5 and 6 Procedure 1 Press the TRANS button 2 Dial 225 3 Select the desired Flexible button 4 Enterthe table entry 5 Enter the desired Allow Deny number 6 Press the Hold Save button PGM Flex Description Default Values 225 Btn used in Station COS 5 and 6 and CO COS 4 01 to 20 Deny Table 2 This parameter selects a Table index and denied digit strings for the Deny Table Not assigned Allow Deny number used in Station COS 5 and 6 and CO COS 4 0 9 and DND as any digit wild card entr
173. t Values 126 Btn Station IP List Description This parameter assigns the IP address of the station when using a LAN for 1 party No assignment IP v4 IP address CTI connection XXX XXX XXX XXX Issue 2 0 July 2010 3 2 17 Station Mailbox Attributes PGM 127 PGM 127 defines the characteristics of a Voice Mailbox including COS Outbound notification of new messages and e mail notification Procedure 1 Press the TRANS PGM button 2 Dial 127 3 Enter the appropriate Voice Mailbox range 4 Selectthe desired Flexible button from the chart below 5 Enter the desired parameter value 6 Press the Hold Save button PGM Flex Description Default Values 127 Btn Administrative 1 A mailbox can be assigned to allow access to other mailboxes and other 0 Disable 0 Disable Mailbox administrative functions 1 Enable Class of Service 2 Each mailbox can be assigned a COS to define specific characteristics of the 1 1 5 mailbox including message storage limitations and message delivery options refer to PGM 238 Announce Only 3 A mailbox can be configured to provide an announcement only and will not provide 0 Disable 0 Disable incoming message storage The Announce Only mailbox can be used for Automatic 1 Enable Park and Page Action after 4 When configured as an Announcement Only mailbox the system will either 0 hang up 0 Hang up Announcement disconnect the call or retur
174. tendant alert Warm Line Timer 8 This parameter sets the length of time the user may activate a feature or access a 05 seconds 01 20 in 1 second CO line before the system activates the Warm line assignment Also see PGM 113 increments Flexible button 7 and PGM 122 Wink Timer 9 This parameter defines the duration of the Wink acknowledgement signal returned 010 100 milli 010 200 in 10 milli by the system to a DID CO line seconds second increments Enblock Digit 10 This parameter determines the inter digit time when Enblock dialing PGM 143 05 seconds 01 20 in 1 second Timer Flexible button 6 is enabled When the timer expires the system sends all digits increments dialed in the call set up message CCR Time Out 11 This parameter defines the first and inter digit time for a caller after receiving CCR 015 seconds 000 300 in 1 Timer Greeting When the timer expires and the user dials no additional digit the call is second increments routed using the digits dialed and the CCR table 228 routing DID Inter Digit 12 This parameter defines the length of time the system waits for each digit from a DID 05 seconds 01 20 in 1 second Timer CO line When the timer expires the system routes the call based on the DID increments process defined FAX Tone Detect 13 This parameter sets the time interval allowed for the system to detect FAX tone 05 seconds 01 10 in 1 second Timer CO line assigned for FAX mode refer to PGM 161
175. ter the appropriate value Press the Hold Save button enc ves nc Qul PGM Flex Description Default Values 381 Btn RSG Number 1 This parameter assigns the number of RSG modules supported The RSG is not supported in ip 60 60 IP Phone number 2 This parameter sets the number of IP Phones to be registered to the system Not assigned 0 16 199 Issue 2 0 July 2010 3 13 3 RSG IP Phone Attributes 382 PGM 382 configures attributes of RSGs and IP Phones registered with the system Procedure 1 Press the TRANS button 2 Dial 382 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 382 Btn Transfer Mode 1 This parameter defines the protocol layer used for communication between the IP 0 IP 0 IP phone and the system ip 60 60 only supports IP 1 MAC Casting Mode 2 This parameter determines if the IP Phone will employ uni cast or multi cast signals 0 Uni cast 0 7 Uni cast when attempting to register with the ip 60 1 Multi cast Tone Source 3 This parameter defines the tone source when connected to an RSGM In the remote 0 Remote 0 Remote mode the RSGM provides tones which reduces rtp traffic 1 LDK Peer to Peer 4 When enabled On a peer to peer connection is established between two IP 1 On 0 Off Phones in the same subnet and the call does not use a VOIB channel for RTP 1
176. the Setup message from the ISDN and the ip 60 60 Setup 0 Off 0 Off Indication Acknowledge message include a progress indication for calls from non ISDN 1 devices CLI Restriction 14 When enabled On the system sends the restrict CLI message when the station 0 Off 0 Off CLIR places an outgoing call on an ISDN or IP line 1 COL Restriction 15 When enabled the system sends the restrict COL when the station answers an 0 Off 0 Off COLR ISDN or IP CO line 1 DID Restriction 16 If this parameter is On the station cannot receive DID calls The DID call will be 0 Off 0 Off treated as an invalid number 1 DID Call Wait 17 If this parameter is set to a second DID call will camp on to the busy Station 1 On 0 Off 1 18 When the CLIP Table Index 143 Flexible button 2 is 50 and the CLI is EXT 0 Short 0 Short Flexible button 5 the CLI Type can be set as Short Flexible button 12 or Long 1 Long Flexible button 19 Long Station CLI 19 When the CLI Type Flexible button 18 is Long and is set as EXT Flexible No default Up to 12 digits 0 9 34 Issue 2 0 July 2010 PGM Flex Description Procedure Values 114 Btn button 5 this entry up to 12 digits is sent by the system 20 When enabled the station if busy receives call waiting tones for a n
177. ting the number of 1 On 0 Off lines defined under Flexible button 4 1 Lines per Page 4 This parameter defines the number of lines per page the system will print before 060 sending a Page Break signal if enabled under Flexible button 3 106 001 199 3 5 16 Print Port Selection 175 PGM 175 defines the output port to receive specific system reports and information as well as the connection for certain software applications Procedure 1 Press the TRANS button Issue 2 0 July 2010 2 Dial 175 3 Select the desired Flexible button 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 175 Btn Off line SMDR 1 This parameter establishes the port for Off line SMDR data output 01 COM1 01 COM 1 Statistics Print 02 COM 2 MODU ADMIN Print 2 This parameter establishes the port for database outputs using 451 01 COM1 03 Telnet 1 Traffic 3 This parameter establishes the port for Traffic Analysis data output 01 COM1 04 Telnet 2 SMDI Print 4 This parameter establishes the port for SMDI data output to an external AA Voice 05 Telnet 3 Mail Not supported in ip 60 60 Call Information 5 This parameter establishes the port for Call information data output 01 COM1 Info On line 6 This parameter establishes the port for On line SMDR data output 01
178. tion Re install the Basic KSU cover en We cO 200 Issue 2 0 July 2010 PGM Flex Description Default Values 100 Btn Nation Code 1 This parameter defines the location of the system using the international dialing 01 N A See the Country Country Code where the system is located Code Chart Site Name 2 This parameter assigns a Name up to 23 characters for the system Not assigned See the Dial Pad Character Map Country Code Chart Code Nation Code Nation Code 1 Argentina 54 Australia 61 Bahrain 973 Bangladesh 880 Belgium 32 Bolivia 591 Brazil 55 Brunei 673 Burma 95 Cameroon 237 China 56 China Taiwan 886 CIS 7 Colombia 57 Costa Rica 506 Cyprus 357 Czech 42 Denmark 45 Ecuador 593 Egypt 20 Salvador 503 Ethiopia 251 Fiji 679 Finland 358 France 33 Gabon 241 Germany 49 Ghana 233 Greece 30 Guam 671 Guatemala 502 Guyana 592 Haiti 509 Honduras 504 Hong Kong 852 India 91 Indonesia 62 Iran 98 964 Ireland 353 Israel 972 Italy 39 Japan 81 Jordan 962 Kenya 254 Korea 82 Kuwait 965 Liberia 231 Libya 218 Luxembourg 352 Malaysia 60 Malta 356 Mexico 52 Monaco 377 Morocco 212 Netherlands 31 New Zealand 64 Nigeria 234 Norway 47 Oman 968 Pakistan 92 Panama 507 P N G 675 Paraguay 595 Peru 51 Philippines 63 Portugal 351 Q
179. tion Range 4 Selectthe desired Flexible button from the chart below 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 111 Btn Auto Speaker 1 When enabled selecting a CO line 055 or other feature button will also 1 On 0 Off Select activate the speakerphone 1 Call Forward 2 When enabled the station can activate Call Forward See Flexible button 18 to 1 On 0 Off enable Off Net Call Forward 1 DND 3 When enabled the station can activate DND Do Not Disturb 0 Off 0 Off 1 Data Line 4 When enabled On if the station is busy tones are not sent to the station and 0 Off 0 Off Security override and camp on from other stations are prohibited 1 Howling Tone 5 When enabled if the station remains off hook taking no action for the ICM Dial 1 On 0 Off SLT tone timer PGM 181 Flexible button 7 the System sends error followed by howler 1 loud error tone Intercom Box 6 When enabled On the station will receive calls from the Door Phone ICM box 0 Off 0 Off Signaling 1 Issue 2 0 July 2010 PGM Flex Description Default Values 111 Btn 7 When enabled transferred CO calls are automatically connected to the station 0 Off 0 Off Answer if in the HF or Privacy Intercom Signal Mode 1 Page Access 8 When enabled On the
180. tion for the group will be active The 1 covering station must have a Coverage button set using Station User Program Button 2 0 0 9 cycles codes 46 and group number Flexible button 1 On Off Flexible button 2 Delay Ring Cycle 3 7 2 2 ACD UCD Hunt Group Attributes PGM 191 Flex Description Default Values ACD UCD Btn VMIB Announce 1 This parameter defines the time the system waits to automatically answer an 015 seconds 000 999 in 1 1 Timer incoming call and play the assigned VMIB announcement Flexible button 3 second increments VMIB Announce 2 This parameter defines the time the system waits after playing the first 000 seconds 000 999 in 1 133 Issue 2 0 July 2010 PGM 191 Flex Description Default Values ACD UCD Btn 2 Timer announcement to play the assigned VMIB announcement 2 Flexible button 4 to a second increments queued call VMIB Announce 3 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 1 Location Announce 1 timer Flexible button 1 expires VMIB Announce 4 This parameter assigns the VMIB announcement number to play when the VMIB Not assigned 00 70 2 Location announce 2 timer Flexible button 2 expires VMIB Announce 5 This parameter sets the interval between the playbacks of VMIB Announcement 2 000 seconds 000 999 in 1 2 Repeat Timer when repeating Flexible button 6 is enabled
181. tton 10 expires 1 Enblock Sending Otherwise digits are sent using Overlap Sending digits are sent as dialed IP lines must be assigned Enblock Sending CLI Transit 7 When calls are rerouted Call Forward the system will send either the original Call 0 CFW 0 CFW Line ID ORI or the forwarding station s CLI CFW 1 ORI Numbering Plan 8 This parameter defines the Type of Numbering Plan the system will use in the Flexible button 1 0 unknown Id Information Element of the call Setup message Flexible button 1 covers outgoing Calling 1 2 ISDN Telephony calls CLI and Flexible button 2 covers incoming calls COL 0 Unknown 3 Data Flexible button 2 4 Telex 0 Unknown 6 National Std Called 7 Private ISDN Call 9 This parameter defines which ISDN Supplementary Service is supported Call 0 No service 0 No Service Deflection Deflection Unconditional Forward or Call Reroute Call Forward No response 1 Call Deflection Rerouting 2 Call Reroute ISDN 1 Dgt Rm 10 When this parameter is On only the 1 digit is removed from the received DID 0 Off 0 Off digits before the number is converted Intended for use in Italy only 1 ISDN Proc 11 If this parameter is call processing information is provided in band Intended 0 Off 0 Off 69 Issue 2 0 July 2010 PGM Flex Description Default Values 143 Btn In band Message for Italy only
182. tton displays the IP Address of the IP phone Display only Display Port View 3 This Flexible button displays the Station Number of IP phone Display only Port Number 4 This Flexible button displays the Port Number of IP phone Display only View NAT IP Address 5 This Flexible button displays the NAT IP Address of IP phone Display only Display NAT Port 6 This Flexible button displays the NAT Port Numbers being used Display only Number STUN Enabled 7 This Flexible button displays the IP Phone NAT PAT status as NAT PAT NAT and Display only PAT or None 202 Issue 2 0 July 2010 PGM Flex Description Default Values 386 Btn CTI Port 8 Not used see 126 Station IP List IPSEC 9 When this parameter is enabled On the VOIB implements IPSec for VoIP packet 0 Off 0 Off traffic 1 Outside NAT 10 This parameter determines if the system provides packet relay for RTP packets 0 Off 0 Off Firewall when behind a NAT Firewall Off RTP packet relay is employed 1 User ID 11 This parameter sets the User Id a Phontage user inputs to register with the ip 60 Not assigned 12 characters See Flexible button 12 for the corresponding Password User Password 12 This parameter sets the Password a Phontage user inputs to register with the ip 60 Not assigned 12 characters See Flexible button 11 for the corresponding User 14 203 Issue 2 0 July 2010 3 13 5 R
183. ues 451 Btn Flexible 1 This selection outputs the Flexible Numbering Plan Numbering Plan Station 2 This selection outputs the Station Database Enter station range CO line 3 This selection outputs the CO Line Database Enter CO line range System 4 This selection outputs the System Feature Database ISDN 5 This selection outputs the Station Group Database ISDN Tables 6 This selection outputs the ISDN Tables Database System Timers 7 This selection outputs the System Timer Database Toll Table 8 This selection outputs the Toll Table Database LCR 9 This selection outputs the LCR Database Other Tables 10 This selection outputs the Other Tables Nation Specific 11 This selection outputs the Nation Specific Database Flexible buttons 12 This selection outputs the Flexible Button Program Enter station range 218 Issue 2 0 July 2010 PGM 451 Networking Flex 13 Description Default Values This selection outputs the Networking Data All Database 14 This selection outputs the database for all PGMs LCD Message Print 15 1 This selection followed by Flexible button 1 outputs the Fixed and Custom Display Messages in the selected language 00 English 00 English 01 Italian 02 Finnish 03 Dutch 04 Swedish 05 Danish 06 Norwegian 07 Hungarian 08 German 09 French 10 7 Portuguese 11 Spanish 12 Korean 13 Estonian 14 Russian 15
184. umbers 1 Enable 0 Disable Access 1 Enable Two way Record 10 When enabled On the station user can record conversations on incoming or 0 Off 0 Off outgoing calls 1 Fax Mode 11 When enabled On CO line calls to an SLT port will ring the port once to notify a 0 Off 0 Off FAX machine of an incoming call In addition calls to the port are not subject to 1 recall and tones such as Camp on are not sent to the port Off net Call 12 When allowed Off Net Forward PGM 111 Flexible button 18 this parameter 1 Ext 0 All ICM amp CO Mode determines the type of calls External CO line calls or All for both external CO line 1 External CO line and Intercom calls the station user can forward Off Net UCD Group 13 When enabled On if the station is a member of a UCD group and is busy DISA 0 Off 0 Off Service and DID calls will route to the group and follow the assigned group attributes 1 Ring Group 14 When enabled On if the station is a member of a Ring group and is busy DISA 0 Off 0 Off Service and DID calls will route to the group and follow the assigned group attributes 1 Stop Camp on 15 If this parameter is enabled Camp on Tone to the station is disabled 0 Disable 0 Disable Tone 1 Enable Line Length 16 This parameter distinguishes the line length when the distance between the station 1 Long 0 7 Short and the system varies significantly Intended for SAF only 1 Long 2 Fa
185. uncement is available the system sends error tone DCO Gain 17 This parameter defines the gain used to supply R2MFC tones to the digital CO line 32 01 63 over the voice path 127 Issue 2 0 July 2010 3 6 2 DCOB Attributes PGM 187 187 is one of several programs that define attributes of digital E1 lines also see 186 Procedure 1 Press the TRANS button 2 Dial 187 3 Enter the appropriate CO Line range 4 Selectthe desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 187 Btn In Digit Type 1 This parameter defines the type of incoming signaling from a digital CO line 2 R2MFC 0 Pulse 1 DTMF 2 R2MFC Out Digit Type 2 This parameter defines the type of outgoing signaling provided on digital CO lines 2 R2MFC 0 Pulse 1 DTMF 2 R2MFC CLI Digit Number 3 This parameter defines the number of digits expected as the Calling Line 10 CO line range 1 Identification from digital CO lines 15 digits 0 9 DCOB TYPE 4 This parameter determines if the digital CO lines support both way calling protocols 2 0 Sweden Cyprus of Sweden or Italy or one way protocols according to Korea standards 1 Italy 2 Korea Australia Send S Block 5 Not used 0 Off Command 1 Issue 2 0 July 2010 3 7 Station Group PGM 190 191 3 7 1 Station Group Assignments
186. w 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 107 Btn Alarm Reset 1 565 Non conflicting 2 to 4 2 566 digits 0 9 and Pickup E UCD Group DND 3 568 Night Answer 4 569 Call Park 5 601 610 Location Range Direct Call Pick 6 7 Up 7 01 824 Access CO Line M d da Group Line Group Number Access Individual 8 88 88 CO line CO Line Number 16 Issue 2 0 July 2010 PGM Flex Description Default 107 Btn Reserved 9 Access Held 10 8 Line Group Access Held 11 8 8 CO Line Individual CO Number Line Access to CO 12 9 Line in the 1 Available CO Line Group Attendant Call 13 0 Door Open 1 14 1 Door Open 2 15 2 Door Open 3 16 3 Door Open 4 17 4 VMMSG Wait 18 8 Enable VM MSG Wait 19 9 Cancel 17 Values Issue 2 0 July 2010 3 1 8 System IP Setup 108 PGM 1068 configures the IP address parameters for the system LAN port Procedure 1 Press the TRANS PGM button 2 Dial 108 3 Select the desired Flexible button from the chart below 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 108 Btn IP 1 This parameter assigns Name up to 15 characters associated with the system s Not assigned 15 characters
187. which is the Country Code used for international dialing to adjust various gain and other characteristics to match the regulatory requirements of the country or region as well as establish a default database If the Nation Code must be changed the system database must be set to default to assure all parameters are changed to match the new Nation Code As this will return all parameters to default values the Nation code should be changed as discussed in section 3 1 1 prior to any other programming During the system default routine the system automatically detects any installed expansion and option boards If an expansion or option board is installed after database initialization the board must be assigned in the system database and logically assigned to a slot order Issue 2 0 July 2010 3 ADMIN PROGRAMMING PROCEDURES 3 1 Basic Set up PGM 100 109 3 1 1 Location 100 PGM 100 defines the country or region for the installation and a Site Name Procedure 1 Press the TRANS PGM button 2 Dial 100 3 Select the desired Flexible button from the chart below 4 Enter the appropriate value 5 Press the Hold Save button If the Nation Code is changed it is necessary to set the database to the default values To default the system 1 Remove the Basic KSU cover Set DIP switch 1 position 4 to the On position Press the Reset button After the system has reset set DIP switch 1 position 4 to the Off posi
188. x 4 Enter the appropriate value 5 Press the Hold Save button PGM Flex Description Default Values 201 Btn COLP CLIP This parameter defines the COLP CLIP to be presented to the ISDN IP CO line when 10 digits 0 9 a station makes or receives a call The entry used is based on the index assigned in PGM 143 Flexible button 1 and 2 143 Issue 2 0 July 2010 3 83 MSN Table PGM 202 PGM 202 defines the telephone numbers and Flexible DID Table index for MSN call routing Procedure 1 Press the TRANS button 2 Dial 202 3 Dial the desired MSN Table index 000 249 4 Pressthe Flexible button for the desired parameter 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 202 Btn CO Line Number 1 This parameter identifies the range of CO lines ISDN or SIP that provide MSN Not assigned Co line number 01 service 36 Index to DID 2 This parameter defines the Flexible DID Table index to use for routing the MSN call Not assigned Flexible DID Table Table when the MSN telephone number assigned under Flexible button 4 matches index 000 999 Sub Number 3 Not Used Not assigned 0 9 Telephone 4 This parameter defines the MSN telephone number to route for this MSN index The Not assigned 20 digits O 9 Number MSN number is received in the Called Party field from the ISDN When the received number matches this entry the call is routed based o
189. y maximum 14 digits 158 Issue 2 0 July 2010 3 9 4 3 Emergency Service Call 226 PGM 226 defines up to ten 14 digit numbers for emergency service when dialed at an active station the number is dialed overriding COS if required Any dial pad digit 0 9 and be entered The default Emergency numbers are 911 and 9911 Procedure 1 Press the TRANS button 2 Dial 226 3 Dial Emergency Table index 1 10 4 Enterthe Emergency number maximum 14 digits 5 Press the Hold Save button 159 Issue 2 0 July 2010 3 9 5 Authorization Code Table PGM 227 PGM 227 defines the Authorization Codes and the associated COS used with certain features such as Call Forward Follow Me DISA calls etc Codes 001 to 048 are for stations and can be viewed only in this table Procedure Press the TRANS PGM button 1 2 Dial 227 3 Enter the Authorization Table index 001 200 4 Select the desired Flexible button 5 Enter the appropriate value 6 Press the Hold Save button PGM Flex Description Default Values 227 Btn Authorization 1 This parameter assigns the Authorization code The code may be a variable length Not Assigned 3 11 digits O 9 Code 3 to 11 digits or a fixed length 5 digits PGM 161 Flexible button 21 Day COS 2 This parameter defines the Day mode Station COS associated with the Authorization 1 9 Code Night

Admin PM-V2-Modified

Contents

Download Pdf Manuals

Related Search

Related Contents