Training session report
Contents
1. eee eee visible on the copydesk at all times whether in full or quarter views It is thus easier to locate the ink screws to be adjusted when you deal with an inking problem 0 a i RPamaBaa Ee KE u i total cost Ink screws numbers as seen in the copydesk 3 5 Sinapse Print Simulators www sinapseprint com New interface for ink screws settings Shots Ink screws settings have been simplified You just need to select the ink screws and to click on or to make the ink levels adjustments AO OPO ON ON PON A a a Be em it M New ink screw panel Limiting the use of the scan densitometer As requested by users it s now possible to allow or forbid the use of the scan densitometer This option is available when launching the software in Software Configuration 4 Software Configuration 7 With two Screens es A ae With Sound Language eye T Disabled scandensitometer Update of measure units for ink dampening solution and varnish Dampening Solution change of conductivity unit Micro Siemens instead of Micro ohms e Varnish use of a4 mm Ford cut to measure varnish viscosity Reference value is between 30 and 60 seconds at 25 C e Standard ink change of the viscosity reference value 150 300 poise but keeping the same measure unit e Standard ink change of the tack unit grams meter instead of TOS that was previously used 4 5 Sinapse P2. Sinapse Print Simulators www sinapseprint com What s New SHOTS V4 6 Release Date October 2008 Version numbers and availability for operating systems Product Version Win2000 WinXP _ Vista SHOTS 4 6 X X X SHOTS Connected 4 6 C X X X VISTA SP1 required New features Consumables Management paper and ink Shots Its now possible to manage paper and ink eiie in the press on a real oo time basis These ID E options can be set up E om in the Trainer module in Context Press Configuration see the Trainer Manual for more details A counter shows the number of sheets at the feeder and at the delivery unit The counter indicates 838 sheets left in the input stack Note see how to add paper in the feeder in the user manual manual or semi automatic method When ink management is activated it may be necessary to add ink with spatula to get the correct ink level and a good inking of the copy 1 5 Sinapse Print Simulators www sinapseprint com Display of good and bad sheets The counter at the delivery unit that used to show the press speed has been modified It now displays the number of good copies when in green or the number of bad copies when in red Here the press has run 1134 bad copies and is still not producing good ones A new print fault gloss problem The gloss problems are now taken into account in the simulator as a fault In case of a
3. gloss problem users are warned by the message PAY ATTENTION Your print copy is bad Remember that a Gloss meter is available in the SHOTS diagnostic toolbox New option for the Spectrophotometer The spectrophotometer can now be used for synchronized or free measurements In the first case by default the points measured on the current copy and the proof are identical One click is enough to measure both When you select the free mode the 2 points to be measured are defined by the user They thus can be located on the same sheet 2 5 Sinapse Print Simulators www sinapseprint com Display of print copies off line Copy viewer J From the Trace Editor at the end of a session you can see each copy taken by m E a a the student and go through it step by AN step These copies can be printed out in A4 or A3 f i h SH CS or A3 format depending on the i wim too ERA OOOO printing machine used VIEW NUMBER 01 el Peer ois Troe an oola lf 3 Pi sy Example of a sheet in the Copy Viewer Deleting Student Traces A password is now necessary to delete student traces in the Trace Editor Limiting the time spent on an exercise In the Trainer Module you can now determine a time span to do an exercise You can decide the maximum time that can be spent on solving a problem Ink screws numbering now visible on the copydesk E Copy Desk Waed Ink screws numbering is now ee a eee ee
4. rint Simulators www sinapseprint com Anomalies resolved in version 4 6 Missing of information of production counter in trace report Shots used to crash when an exception was created using emergency stop Wrong tack unit Wrong ink viscosity unit The varnish viscosity was too high Wrong unit for conductivity No confirmation and password before deleting a trace file Print copy history not deleted with the trace report Simulator looses the connection with the copydesk The usage of the ink screw was too complex Begin time and End time had no effect on the SHOTS session Virtual time was using more copies than set Gloss problem print fault was not diagnosed by the simulator No value for the dampening level in the 6th unit No management of ink and paper Ink screw numbering not present on the copydesk No information about spectrophotometer or scanning densitometer activity in trace report Copydesk used to crash when you got a new copy while the manual densitometer was open 5 5
Download Pdf Manuals
Related Search