Home
Manual - FAST.Eu
Contents
1. Blue Red Green Colour 100 100 100 Turquoise 0 100 100 Light green 0 0 100 Green 100 0 0 Blue 50 100 0 Violet 0 100 0 Red 0 0 0 Colourless display 0 100 10 Orange Operating tips 1 Regularly clean the aluminium filters and regularly replace the carbon filters 2 Use the medium exhaust power level Only use the highest power level when necessary 3 To ensure proper ventilation leave windows closed while the appliance is turned on Copyright 2012 Fast CR a s EN 15 Revision 04 2012 PART 5 MAINTENANCE AND CLEANING WARNING Before cleaning regular or other maintenance installation or removal check that the appliance is turned off and disconnected from the power socket or that the respective circuit breaker is turned off Changing alight bulb e Turn off the appliance e Take out the aluminium filter e Ifthe light bulb broke during operation wait until it cools down Models with a 50 W halogen light bulb e To remove the halogen light bulb 50 W press the light bulb holder downwards and gently turn it anticlockwise Remove the light bulb e Install a light bulb with the same parameters in reverse sequence Models with a 20 W light bulb e To remove the halogen light bulb 20 W first remove the glass cover using a thin screwdriver Be careful
2. not to scratch the appliance Remove a faulty light bulb by pulling downwards and insert a new working light bulb e Usea light bulb with the same parameters NOTE Do not hold the light bulb with your bare hands Dirt or sweat from the hand may shorten their lifetime EN 16 Copyright O 2012 Fast CR a s Revision 04 2012 Cleaning Aluminium filters capture dust and fat from the extracted air e Itis necessary to regularly wash these filters ideally once a month depending on the level of use Wash the filters in water with dishwashing detergent or you may place the filters in a dishwasher and wash them using a gentle program max 60 C e Take out the aluminium filters by pressing the clip e After cleaning allow the aluminium filters to dry thoroughly before reinstalling them e Wipe the outer surface of the range hood with a clean damp wiping cloth lightly dipped in water with a small amount of dishwashing detergent Then wipe dry e Avoid electrical parts coming into contact with water or another liquid Cleaning the aluminium filters Models with digital controls 3 speeds Aluminium filters need to be cleaned when C depending on the model appears on the display e g every 2 3 weeks depending on the level of use Clean the filters according to the above mentioned instructions and after reinstalling them press and hold down the fan button for 3 seconds until the C symbol depending on th
3. 2012 Fast CR a s Revision 04 2012 PART 2 DESCRIPTION OF THE APPLIANCE PEI 9703 Oo Outer chimney Inner chimney Tempered glass Lighting Aluminium filter Control panel PEI 9704 Remote control Optional accessory AP NS Outer chimney Inner chimney Lighting Aluminium filter Control panel c lt 0 p Hoe A p B gt D A Turn the appliance on off B Increase the exhaust power C Decrease the exhaust power D Turn the lights on off EN 4 Copyright 2012 Fast CR a s Revision 04 2012 PART 3 INSTALLATION Unpacking e After unpacking remove all packaging and advertising labels from the appliance Check that the appliance has not been damaged and that the package includes all the items described in this user s manual If the appliance was damaged during transport contact authorised service centre Do not use a damaged appliance under any circumstances IMPORTANT Ensure that children do not play with the packaging material Dimensions of the appliance PEI 9703 Min 515 Max 970 PEI 9704 Min 520 Max 975 Supplied accessories depending on the model N A non return exhaust flap must be installed into the air outlet of the range hood unless one is already factory installed EN 5 Copyright 2012 Fast R a s Revision 04 2012 Placement Min 65 cm Min 75 cm Install the range hood at a height of a
4. down WASH FILTER the fan button for 3 seconds until th symbol depending on the model disappears from the display 3 symbol depending on the model appears on the display after approximately 60 hours of operation EN 17 Copyright 2012 Fast R a s Revision 04 2012 WARNING For cleaning do not use petrol benzene thinners or any other solvents coarse cleaning agents steel wool or any sponges with steel wool WARNING You may put the aluminium filters in a dishwasher The colour of the aluminium filters may change after several washes This is normal EN 18 Copyright O 2012 Fast CR a s Revision 04 2012 PART 6 BEFORE YOU CALL THE SERVICE CENTRE If the appliance is not working as it should check the following recommendations for resolving the most common problems If the problem persists or it is not included in the table below turn off the appliance and disconnect it from the power socket and contact an authorised service centre Problem Solution The range hood is not working Check that the power plug is properly inserted in a properly grounded power socket with the parameters 220 240 V 50 Hz Check that the motor power switch is in the On position The lights are not working Check that the power plug is properly inserted in a properly grounded power socket with the parameters 220 240 V 50 Hz Check that the motor power
5. switch is in the On position Check whether the light bulb or fluorescent tube is broken Exhaust power is weak Check whether the aluminium filters are dirty Check the air outlet it should be open Check whether the carbon filter is not too dirty The range hood does not extract the air directly out for models without an exhaust Check whether the aluminium filters are dirty Check whether the carbon filter is not too dirty ATTENTION Use the range hood together with the stove This will ensure the correct air exhaust We recommend to leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted Copyright 2012 Fast CR a s EN 19 Revision 04 2012 a Z O rm lt J U LLI O u lt U Z T U LLI PART 7 ww 07L ww OZ L ww OZL ww OZL ww OZL ww OSL WW OSL ww OSL 1939U1eIp 33 NO Aly ZH 0S ZH 0S ZH 0S ZH OS ZH OS gt ZH OS ZH OS ZH 0S slejok nduj Nor 077 NOFZ 0ZZ NOKZ 0ZZ NOT 0ZZ NObZ 0ZZ NOT OZZ NObZ OZ NOKZ OZZ 19 709 L9 ap 219 SSION o
6. the appliance create a fire hazard or cause injury to persons e Neither the manufacturer nor the vendor take responsibility for damages cause by incorrect or unprofessional installation connection or operation Tampering with the appliance by an unqualified person will void the customer s right to a warranty repair e Do not expose the power cord to excessive pressure or loads do not place heavy objects on it it must not be tangled and it must not be stepped on Do not locate the power cord in or on heat sources such as stoves heating or other generators of heat Otherwise this may damage the power cord or create a fire hazard e Only connect the power cord plug to a power socket after the entire installation is completed e The power plug serves as a disconnection device and for this reason the power socket must remain easily accessible for the event of a dangerous situation unless it is connected into a terminal box e Do not touch the lights if the appliance has been running for some time Lights heat up during operation and may cause burns e This appliance is designed for fume extraction during standard domestic use Do not use the appliance for purposes other than those for which it was designed Otherwise you expose yourself to the risk of a dangerous situation and voiding the warranty Follow the instructions for installation and ventilation with the exception of when a fire stove is used Do not use the flamb cooking method und
7. to the side freely standing or built in stoves so that you have easier access to the rear wall or ceiling If this is not possible place protective material on to the work area cooktop or stove This will prevent damaging these surfaces e Select an even surface for the necessary assembly of the range hood Cover the surface with a protective material and place all parts of the range hood and fastening elements on to it e tis necessary that a qualified technician inspects the suitability of the supplied fastening material and other components for the specific wall ceiling type The wall ceiling must be sufficiently strong to hold the weight of the range hood EN 6 Copyright O 2012 Fast CR a s Revision 04 2012 e Donotattach this range hood to a wall or cabinet furniture by tiling plastering and do not glue it on using silicone glue The appliance is designed to only be installed on a wall ceiling e We recommend that always two people perform the installation of the appliance If your range hood is designed to be mounted to the ceiling adhere to the following instructions e The range hood must only be suspended on ceiling beams or on load bearing ceiling beam connections e Do not suspend the range hood on false ceilings e The ceiling must have a load bearing capacity of at least 40 kg e The ceiling thickness must be at least 30 mm IMPORTANT THE RANGE HOOD MAY ONLY BE CONNECTED TO THE ELECTRICAL GRID AFTER THE ENTIR
8. E INSTALLATION IS COMPLETE 1 Installation of the hanging plate Place the hanging plate on the ceiling and mark the points for drilling holes for the screws Check that the front part of the hanging plate labelled FRONT is facing in the same direction as the control panel a Into the designated locations A B C D drill 10mm holes for screws Depending on the surface of the ceiling use an appropriate drill bit size b Insert dowels into the drilled holes A B C D Check that the dowels are properly inserted c Use screws 5 5 x 45 to attach the hanging plate to the ceiling Check that the hanging plate if firmly and properly attached 4 Hanging hole Hanging plate 2 Installation of the angle sections The front angle sections must be installed in the left right direction and the rear angle sections the other way round Attach the angle section to the motor base according to the illustration You can then set the height of the range hood by setting various positions of the angle sections relative to the motor unit Check that all angle sections are installed at the same height and that the front part of the motor unit is facing in the same direction as the front part ofthe hanging plate and control panel EN 7 Copyright 2012 Fast CR a s Revision 04 2012 Connection of the front angle Connection of the rear angle sections left to right direction sections right to left direction Place for connecting t
9. RANGE HOOD USER S MANUAL PHILCO ES Famous for Quality the World Over PEl 9703 PEl 9704 Dear customer Thank you for buying a PHILCO brand product So that your appliance serves you well please read all the instructions in this user s manual CONTENTS PART 1 IMPORTANT SAFETY INSTRUCTIONG ssssssssssssssssssssesssssssessessesscesesssnssesesesessssenssscesesssssensceseseees 2 PART 2 DESCRIPTION OF THE APPLIANCE scscsssssssssssesssssssssnssssessessessenssssessensnssesecssessensussesssssessensceseseees 4 PART 3 INSTALLATION c ssscsssssssssssssscsscesssssssessesscesssssnscssesecssssseuscssessssessesscssessssssesesesssssssusescesesessssesscaseseees 5 UNPACKING esas taa aida 5 Dimensions of the appliance Placement Assembly and installation ofthe applies 6 Carbon filter Ventilation PART 4 OPERATION ssscsssssssssssssssssessesscssssessessesscssessensnssesscssessenscssessessessenscssesssssnssesesesessensussesecesesseseneseses 13 Mo delswithidigitalcontrols 3S peed Sam nnna a EEA RENTE aan 13 Modelswith digital controls 5S peed Siisera siei EOE RE Ea E NS 13 Models with an LCD display 5 speeds Operating tips PART 5 MAINTENANCE AND CLEANING csccccssssssssssscscsssssssssssscssescssnssesssesessssssesesssessssnscesesesessenesenssesee 16 Changing alight Dolina its 16 Ci ia 17 PART 6 BEFORE YOU CALL THE SERVICE CENTRE ocononoccncncnconononcnononcnnonononcnononc
10. crease in half second intervals If you set the exhaust power level to maximum 5 the appliance will work at the maximum exhaust power level for 15 minutes and then continue at the exhaust power level of 2 The maximum exhaust power level is called turbo speed Timer TIMER button Set the operating time of the appliance with a countdown feature during operation Each time it is pressed the power level will decrease by 1 level If you press and hold down this button for at least 2 seconds the power level will decline faster TIMER button Set the operating time of the appliance with a count up feature during operation Each time it is pressed the power level will increase by 1 level If you press and hold down this button for at least 2 seconds the power level will increase faster Timer functions 1 Turn off the range hood If you set the timer while the range hood is running the range hood will stop running lights will turn off and a warning sound will be emitted for 5 seconds after the timer duration comes to an end 2 Alarm If you set the timer while the range hood is not running then an alarm will be set As soon as the set time of the timer comes to an end a sound will be emitted for 15 seconds The range hood will not stop and the lights will stay on if the alarm timer turns off If a timer is not set the clock is displayed Clock The clock on the display shows the current time If the clock is set the colo
11. e model disappears from the display The symbol E depending on the model will appear on the display which means that the appliance is ready for operation If you wish to use the appliance without clearing the C symbol depending on the model press the o button to start extraction for 1 second then the C symbol depending on the model will appear again and the motor will continue running Models with digital controls 5 speeds The aluminium filters need to be cleaned when C appears on the display depending on the model Clean the filters according to the above mentioned instructions and after reinstalling them press and hold down the fan button for 3 seconds until the C symbol depending on the model disappears from the display The symbol E depending on the model will appear on the display which means that the appliance is ready for operation If you wish to use the appliance without clearing the C symbol depending on the model press the fan button to start extraction for 1 second then the C symbol depending on the model will appear again and the motor will continue running NOTE The C symbol depending on the model appears on the display after approximately 60 hours of operation Models with an LCD display 5 speeds The aluminium filters need to be cleaned when ppears on the display Clean the filters according to the above mentioned instructions and after reinstalling them press and hold
12. el based on the use of the stove and the amount steam that the pots emit Press the respective button on the control panel 1 lowest exhaust power Il medium exhaust power Ill highest exhaust power Automatic timer TIMER All models with a remote control are equipped with an automatic timer Press and hold the respective button for the exhaust power level for at least 2 seconds and the automatic timer function will be turned on for a period of 15 minutes When the function is turned on the respective symbol will appear on the display and the motor will turn off automatically after 15 minutes NOTE Use the range hood together with the stove This will ensure the correct air exhaust We recommend to leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted Lighting The range hood is equipped with lighting Press the button with the light symbol to turn on the lights Press the button again to turn the lights off Models with digital controls 5 speeds Exhaust power selection This range hood is equipped with 5 levels of exhaust power Select the power level based on the use of the stove and the amount steam that the pots emit To turn on the motor press the button and to set the exhaust power level press the or button Press the button to increase the exhaust power and the button to reduce the exhaust power Automatic time
13. er the range hood Regularly replace the filters in the range hood Otherwise this presents a fire hazard Only use filters suitable for use with the range hood The manufacturer or distributor will recommend the suitable filter type e Do not use the appliance without the aluminium filter inserted Do not take out the filters while the appliance is on e Regularly clean the appliance to prevent a dangerous situation from occurring e Before cleaning replacing filters moving or any other maintenance turn off the appliance and pull out the power plug from the power socket or turn off the respective circuit breaker e Ifyou are using another gas or natural gas appliance in the room at the same time the fumes from this appliance must be spatially isolated EN 2 Copyright O 2012 Fast CR a s Revision 04 2012 e Ifa chimney is connected to the exhaust of the range hood use pipes with a diameter of 150 or 120 mm The pipe connection should be as short as possible e Keep packaging materials out of children s reach They could suffer injury or suffocation e Children must be supervised to ensure that they do not play with the appliance If the power cord is damaged stop using the appliance Have the power cord replaced at an authorised service centre or by another qualified person Under no circumstances should you replace the power cord yourself To ensure safety use a fuse with a maximum rating of 6 A WARNING This appliance m
14. he angle sections 3 Installing the chimney to the motor unit FRONT i Front part of the motor unit Insert the inner chimney into the outer chimney To temporarily join the chimney use the screws from the motor unit The chimney will then not fall during the installation to the hanging plate The screw holes of the inner chimney should fit with the motor unit 4 Attaching the motor unit to the hanging plate Lift the motor unit and align the free ends of the angle sections with the corners on the hanging plate see illustration below Ensure that the front part of the hanging plate is facing the same direction as the front part of the motor unit and also as the control panel EN 8 Copyright 2012 Fast CR a s Revision 04 2012 Use screws 3 5 x 9 5 to connect the ends of the angle sections to the corners of the hanging plate Place for connecting to the hanging plate 5 Installation of the aluminium exhaust tube Attach one end of the aluminium tube to the range hood flange and the other end to the air outlet Check that both ends are firmly attached and secured in place 6 Attaching the inner chimney Pull out the inner chimney in the upwards direction Level with the hanging plate and attach using screws 3 5 x 9 5 Place for connecting the inner chimney EN 9 Copyright 2012 Fast R a
15. n between the hours and minutes will flash once a second Setting the time 1 Press the and buttons at the same time 2 The hours and minutes will start to flash for 5 seconds 3 In this time press the G or button to set the hours or minutes If a power outage occurs it will be necessary to set the time again Timer Lamp step on off waa s 8 S LS ate OO EN 14 Copyright O 2012 Fast CR a s Revision 04 2012 Additional functions Additional functions may be set only when the motor and the lights are off 1 Setting the backlight brightness Press and hold the button after about 5 seconds the blue colour intensity in percent will appear e g b00 Press the button once and the colour of the display colour will change to red e g r100 press the button once more and the display colour to green e g g10 After selecting the colour use the G buttons to set the brightness of the respective display colour e g 0 100 To confirm the setting press and hold the button for approx 5 seconds A sound will be made If you do not wish to save the setting press the button or the button for the light 2 Backlight The display backlight is always on Press and hold the button for approx 5 seconds A sound will be made Now you can turn off the backlight If you wish to again turn on the display backlight press and hold down the button for approx 5 seconds
16. onononononononconononononoc co rcncnonononess 19 PART 7 TECHNICAL SPECIFICATIONG s ssssssssscssssssssssscsssseresssssnscssssessessesscesesessssesesesesessenssssesecessssenesssesee 20 EN 1 Copyright 2012 Fast CR a s Revision 04 2012 PART 1 IMPORTANT SAFETY INSTRUCTIONS Recommendation Carefully read these instructions before installing and operating this range hood Write down the serial number found on the rating label of the range hood in the space below It is essential that you store this user s manual in a safe place so that you can use it in the future If you intend to sell the appliance give it to another owner or if you move always make sure that the user s manual is attached to the appliance so that the new owner can also learn about the operation of the appliance and the relevant warnings SERIAL NUMBER Important safety instructions e This appliance is designed for household use only e Before connecting the power cord plug make sure the voltage stated on the rating label of the appliance corresponds to the voltage in your wall socket Connect the power cord plug to a power socket with a voltage of 220 240 V 50 Hz e Only use a properly grounded power socket The appliance may only be connected to a properly grounded power socket e All electrical connections must be performed by a qualified electrician e Installation performed by an unqualified person may cause incorrect operation damage to
17. r TIMER All models with a remote control are equipped with an automatic timer Press and hold the button at the set exhaust power level for at least 2 seconds and the automatic timer function will be turned on for a period of 15 minutes When the function is turned on the respective symbol will appear on the display and the motor will turn off automatically after 15 minutes EN 13 Copyright 2012 Fast CR a s Revision 04 2012 NOTE Use the range hood together with the stove This will ensure the correct air exhaust We recommend to leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted Lighting The range hood is equipped with lighting Press the button with the light symbol to turn on the lights Press the button again to turn the lights off Models with an LCD display 5 speeds This range hood is equipped with 5 levels of exhaust power Select the power level based on the use of the stove and the amount steam that the pots emit On Off button X Press the button once to turn on the range hood The initial exhaust power level is 2 Press again to turn the range hood off Setting the exhaust power level To set the exhaust power level press the or button Press the button to increase the exhaust power and the button to reduce the exhaust power If you press and hold down the button for at least 2 seconds the exhaust power levels will increase de
18. s Revision 04 2012 7 Removing the separation plate To remove the separation plate hold the plate in the appropriate points on the left and right and pull downwards 8 Connecting the control unit to the motor unit Align the hanging hooks on the control unit with the appropriate holes for the hanging hooks on the motor unit and join together using screws 3 5 x 9 5 Hanging hook Hole for the hanging hooks on the motor unit 9 Wiring connection Connect the 220 V socket for the power cord with an appropriate motor socket Insert the aluminium filters when the connection is performed EN 10 Copyright 2012 Fast R a s Revision 04 2012 During installation perform the connection as shown in the illustration below to activate the use of the control panel To connect first bend the tabs outwards They will connect after the connection is made EN 11 Copyright 2012 Fast CR a s Revision 04 2012 Carbon filter If you are using the range hood without an air exhaust it is necessary to use a carbon filter The carbon filter is not included Contact your vendor or an authorised service centre to purchase this filter e Before installing or replacing the carbon filter check that the appliance is turned off and disconnected from the power socket or that the respective circuit breaker is turned off e tis nece
19. se S9 OSE Oz HUILA ounssoud m OSZ OSZ 0S U WU Moy any m 017 017 017 M 42M0d u L L L v abez oA S ES ves ES ap 9n9 asion OZE STE OLE Oz HUILA ounssoud m 0Lb SSY OSY y U1 Moy Aly m SZL SZL OLL M 14amog gt 8 0 8 0 80 v bejjon 6v ES SS SS 6v zs 8b ap 9n9 asion S8z dd 007 08L 067 za soc oz Hua eansserd v SZE 007 005 007 09 005 SEE y U1 MOJ Aly m OSL OLL ozz OLL OSL S81 Stl M Jamod w LO 60 9 L 8 0 vo SI LO v abeyJon Er 0s vs 8b S Ly o er zv ev ap 242 9SION SEZ SoZ 061 081 sol DEZ soz 007 ozHww ounssoud m 067 SLL 007 OLE SZZ soz OLE 097 y U1 Moy Aly m SZL S6 OLL O 06 DEl 07l SZL M Jamod o 90 90 60 TI 90 90 60 90 v SBeJJON ve vy Sv Ov Er L 6 SE 9 ap 9n3 3sl0N SSL 081 091 091 OSL OZL SSL OEL Oz Hu ounssoud m 017 SSL 061 OSZ 061 007 OEZ 081 y U1 Moy Aly M OLL 08 08 SEL 02 id 06 SOL M 42M0q so 90 90 L so so 90 so v GejjoA 9019 Dad L0S9 Ad SOv6 24d 8029 8d oops 33g 9099444 Zoss 334 sov9 Dad lad mad t to change is subjec d data i tone All the here ment NOTE EN 20 Revision 04 2012 Copyright 2012 Fast CR a s EN 21 Copyright 2012 Fast CR a s Revision 04 2012 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Di
20. spose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES CE The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your seller This product meets all the basic EU regulation requirements that relate to it Changes to the
21. ssary to replace the carbon filter regularly every 3 5 months depending on how much the appliance is used e Never wash the carbon filter in water unless the manufacturer states otherwise e Aluminium filters must always be installed even when the carbon filter is not installed Do not use the appliance without the aluminium filter installed Replacing the carbon filter 1 For the correct operation of the appliance it is necessary to install a carbon filter The number and type depends on the model 2 Place the carbon filter on the motor outlets and turn it in the clockwise direction 3 Toremove the carbon filter turn it in the anticlockwise direction Ventilation To ensure proper ventilation leave windows closed while the appliance is turned on WARNING Pay increased attention if you are using the appliance together with another appliance that uses air or fuel for its operation e g heating fan fan etc or that uses gas coal or wood as its operation may negatively affect the performance of the range hood because it expels air out of the room This warning does not apply if you installed the appliance without an exhaust out of the room EN 12 Copyright 2012 Fast CR a s Revision 04 2012 PART 4 OPERATION Remove the protective foil from the control panel Models with digital controls 3 speeds Exhaust power selection This range hood is equipped with 3 levels of exhaust power Select the power lev
22. t least 65 cm above an electric cooktop or at a height of 75 cm above a gas cooktop Assembly and installation of the appliance Before assembling and installing the appliance carefully read these instructions and adhere to them NOTE Dowels screws and the hanging plate are supplied together with the range hood IMPORTANT Before installing or using the appliance please first read all instructions and check that the voltage and frequency values on the rating label correspond to the voltage and frequency in your electricity grid We recommend that the appliance be connected by a service technician or another qualified person in compliance with local codes and regulations Before starting the installation e Check that the purchased appliance has the correct dimensions corresponding to the chosen installation location Furthermore ensure that there is an electrical power socket available that will remain accessible even after the range hood is installed Before installing the range hood check that all necessary masonry work is complete Have all electrical connections performed by a qualified person We recommend that you remove the aluminium filters before installing the range hood Check that there are no packaging materials or other materials e g user s manual warranty card or bags with screws inside the appliance These need to be taken out and kept for possible use in the future e We recommend that you disconnect and move
23. text design and technical specifications may occur without prior notice and we reserve the right to make these changes EN 22 Copyright 2012 Fast CR a s Revision 04 2012
24. ust not be used by persons including children with physical or mental impairments or by inexperienced persons unless properly trained or schooled in the safe use of the appliance or unless they have been properly supervised by a qualified person who will be responsible for their safety Attention when transporting or carrying The packaging materials are from recyclable materials so dispose of them in an environmentally conscientious manner according to regulations in force During transport adhere to the symbols of the cardboard box When carrying the appliance hold it by the respective handles NOTE We recommend that you keep the original packaging at least for the duration of the warranty period for the event of repair or refund and transport to the authorised service centre Adhere to the symbols on the cardboard box If you do not have the original cardboard box adhere to the following instructions a Donot place any items on the appliance that could damage the appliance during transport b Protect the appliance against impacts falls etc c Wrap the appliance e g in bubble wrap which will protect the appliance from damage NOTE The carbon filter is not included NOTE If the building is equipped with a heat recovery system system it is necessary to setup the appliance for internal air circulation without an exhaust In that case it is necessary to purchase the carbon filter EN 3 Copyright
Download Pdf Manuals
Related Search
Related Contents
2N OfficeRoute - Digital Angel conoscenza del veicolo SHARP 施工・取扱説明書 Station centrale de monitorage cardiaque ICENTRAL GE Senseo Senseo HD7812/53 coffee maker Fisher Price Lion with game activities Handbuch - honda center hütter SERIE GT-GS Copyright © All rights reserved.
Failed to retrieve file