Manual - Korenix
Contents
1. Power Supply Packet throughput ability 5 to 95 non condensing Dimensions 54 mm W x 135 mm H x 105mm D C rem 0 EN61000 4 2 EN61000 4 3 EN 61000 4 4 EN61000 4 5 EN61000 4 6 EN61000 4 8 EN61000 4 11 IEC60068 2 32 Free fall Stability IEC60068 2 27 Shock IEC60068 2 6 Vibration A 2 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual B Revision History Document Edition Revision Details one March 2004 Added descriptions related to JetNet 3008 9 May 2005 Added descriptions related to JetNet 3005f 4 DEC 2007 Add notice related to JetNet 3005f2. needs to connect several modems simultaneously in order to let a big number of users to access this industrial network However Computer A does not have additional COM ports to connect all of the modems For this reason we use a network solution Computer A JetNet3005 Industrial switch Ethernet to S Serial SD ID Converter oo 4 MODEM PSTN Line 18 We network enable the modems via serial to Ethernet converters and use Ethernet cables to connect Computer A and converters to the JetNet 3005 Enter Command Line mode in Computer A and use ping command to see if the connections between Computer A and the converters are working properly as described in step 10 and 11 19 Enter Telnet program in Computer A type in the IP address of one of the converters and configure the serial port s communication parameters Follow this procedure to set up the other converters 20 Install the virtual com port driver and enter converters IP addresses 21 Click on Computer A s Control Panel Device Manager and make sure the system each converter s IP address is mapped to the corresponding com port 22 Click on Computer A s Dialer and install modem driver Configure the modem s corresponding com port as a virtual com port enter a set of telephone number and start dialing Verify that the modem did dial up and the serial port s communication parameters are correct Follow this procedure to verify each converter s parameters are correc
3. preventing any power interruption 6 Check the LED for PWR1 and PWR2 to make sure that your JetNet is operating normally Note If you are using DC IN power jack to supply power to the JetNet please check the PWR LED 7 Use Category 5 straight through Ethernet cables with RJ45 connectors to connect network 8 devices Connect one side of an Ethernet cable with a RJ45 connector to the JetNet s Ethernet port RJ 45 port and the other side of the Ethernet cable to the network device s Ethernet port RJ 45 port Note Make sure that the connected network switches support MDI MDI X function If they do not support this function use a crossover Ethernet cable 9 Check the port status LED indicator blinking green on the JetNet to see if the network connection is successfully established 2 10 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 10 11 12 Hardware Installation Power on the host activate the Command Line mode and ping the connected Ethernet device to see if it will respond To enable the Command Line mode click on Run in the Start menu type Command and click on OK to continue a windows Update E reum 2 x azo Programs k od ajx Documents k pm Type the name of a program folder document or od Internet resource and Windows will open it For vou Settings S n command Search d Help OK Cancel Browse
4. Ethernet Rail Switch User s Manual 2 5 Wiring the Power Inputs 1 Insert the positive and negative wires into the V and V contact on the terminal block connector Note The suitable electric wire ranges from 12 to 24 AWG Note The additional power jack is designed for office use Wiring the Ethernet Ports RJ 45 ports with auto MDI MDI X function JetNet 3005 3005f has five four 10 100 Mbps auto sensing ports for 10Base T or 100Base TX device connection The UTP ports will auto detect 10Base T and 100Base TX connections Auto MDI MDI X function allows users to connect another switch or workstation without changing straight through or cross over cabling See the figures below for the schematic diagram of straight through and cross over cabling switch kKourer Gr FK Switch Switch 3 TD gt 3 RD 3 TD 3 TD 6 TD v5 RD 6 TD 6 TD RD RD RD 1 TD 2 RD 2 RD 2 RD 4 2 TD Straight through Cabling Schematic Cross over Cabling Schematic All ports of JetNet 3005 3008 support auto MDI MDI X function When you use an Ethernet cable to connect other devices such as computers switches or hubs pin 1 2 3 and 6 of the 8 pin RJ45 connector are used to communicate with the connected devices Pin1 2 3 and 6 s signals are converted by the MDI X function as shown in the table below Pin MDI X MDI Signals 2 Do 7 o6 T m Wiring the Fiber Ports To connect the fiber p
5. Shut Down Type ping 192 168 1 1 command to check the connection Here we use IP address 192 168 1 1 as an example C 5 gt ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data Reply from 192 168 1 1 bytes 32 timetiims TTL 255 Reply from 192 168 1 1 hutes 32 time lt ifims TTL 255 Reply from 192 168 1 1 bytes 32 time lt ifims TTL 255 Reply from 192 168 1 1 bytes 32 timesilms TTL 255 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost Oz loss gt Approximate round trip times in milli seconds Minimum Ams Maximum ms Average ms IER 13 Repeat step 10 to make sure that the connection of each device connected to the JetNet 3005 3008 3005f is successfully established 14 Power on the host activate the Command Line mode and ping the connected Ethernet device by typing ping t 192 168 1 1 command to see if it will respond 15 The parameter t allows you to continue to ping the network device as shown in the figure below GiM ping t 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data from from from from from from from from from from from from from from from from from from from from 1972 1972 192 192 192 192 192 192 192 192 192 192 192 192 192 192 192 1972 192 168 168 163 168 168 168 168 168 168 168 168 168 168 168 168 mE 168 168 168 L L LI L pnk pm panh pak pak ponk jamk pok pk p
6. power outlet IF you still cannot resolve the problem contact your local dealer for assistance A Specifications IEEE 802 3 10BaseT Ethernet Standards IEEE 802 3u 100BaseT X 100BaseF x Fast Ethernet IEEE802 3x Flow Control and Back pressure Protocols CSMA CD Technology Store and Forward T 14 880 pps for Ethernet port Transmission Rate 148 800 pps for Fast Ethernet port JetNet8005 3005f 1K MAC address table MAC address table size JetNet3008 2K MAC address table JetNet3005 3005f 512Kbits Memory Buffer JetNet3008 1024Kbits B Per port Link Activity Green Full duplex Collision Orange B Per unit Power Power 1 Power 2 Green 10BaseT twisted pair UTP STP Cat 3 4 5 cable EIA TIA 568 100 ohm 100m 100BaseT X twisted pair UTP STP Cat 5 cable EIA TIA 568 100 ohm 100m SC Multi mode 50 125um 62 5 125um SC Single mode 9 125um 10 125um Available distance 2KM Multi mode 30KM single mode Wavelength 1310nm multi mode single mode Network Cables 12 to 48 VDC redundant dual DC power inputs with reverse polarity protection and a removable terminal block for master and slave VDC power inputs JetNet3005 2 8 Watts Power consumption JetNet3008 4 6 Watts JetNet3005 3005f 0 74Mpps 9 64bytes 51TX 4TX 1FX JetNet3008 1 19Mpps 64bytes 8TX Installation DIN Rail kit and wall mounting panel Operating Temperature 10 C to 70 C Operating Humidity 5 to 9596 non condensing
7. Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Fourth Edition DEC 2007 korenix www korenix com Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Copyright Notice Copyright 2005 Korenix Technology Co Ltd All rights reserved Reproduction in any form or by any means without permission is prohibited Table of Contents Chapter 1 IntFOdU CHO ucc eet tL sea EE EE 1 1 OS 017 PP 1 2 Product POALUNCS mc TE T UMS 1 2 Package OBeokliSDu scott cc tio Een o ntn tE M Unibet otiosi donee cunda 1 2 Chapter 2 Hardware Installation iusicici ie eni asap occa 10203 ec 000402 CO cea casados eoe a er serica erue 2 1 Jnyifojo Deo 2 NONE CRM n 2 2 Fanell euer LL 2 2 DIMENSIONS TT T T DE EE 2 3 LED Trid Ca DO B BaetsusossUovdues Visi Duexs ein vic Uetwsesozsid bora fa basin eee aee AR Uo dde db ad 2 3 Blond PA 2 5 VVIGING the Power INpuls eus c urba ede duse Outer tarda ne Br e cod t dou UE 2 6 Winnog tbe INCENSE I GUS sideris IER uae S TURA URS Lube tela cuta ESL ddiu Ld a Blot 2 6 Wiring the FIDSr Portes eee haga uo Qesko adueo Qo Pub caet E eR Ua PRU RERBA a 2 6 UNG TENERLO 2 7 DIN Rail Mounting Installation ccccccccccssececeseeeseeeeseeeeseesessueeeseeeessesesaneesees 2 7 Walls MOUNTING DSTI ODIs soo cae ode utes ast uv bo A a ipie etu 2 8 Iristallation and TESTING ussseoiasupeosev
8. ah ponk pak pank poak pk jonk jamk L L i L L LI LI L L L LI L L LI LI L L L L L eS pok pk pah pnk pak ponk poak pk jonk jamk EE hytes 32 z bytes 32 bytes 32 EM hytes 32 hbytes 32 gt hytes 32 gt hytes 32 hytes 32 gt hytes 32 hbytes 32 EE hbytes 32 gt hytes 32 hbytes 32 gt hytes 32 gt hytes 32 gt hytes 32 hytes 32 z bytes 32 hyutes 32 hbytes 32 time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims time lt ims TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 TTL 255 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 2 11 Before you continue make sure that both PWR1 and PWR2 are successfully connected to power sources When PWR1 fails the LED for PWR1 will go out At that moment if the ping command is still being replied to then it proves that the redundant power input function works normally 16 Exit the Command Line mode and connect PWR1 power input At this stage your JetNet 3005 3008 3005f has been tested and the installation is complete 17 See the figure below for setting up your industrial network with JetNet 3005s Computer A
9. ble below gives descriptions of the function of each LED indicator Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 2 3 on Off No power is being supplied Off No power is being supplied Power is on Off No power is being supplied A network device is detected LNK ACT of Port 5 The port is transmitting or receiving packets from the TX FX device Off No device is attached The port is operating in full duplex mode FDX COL of Port 5 Collision of packets occurs The port is in half duplex mode or no device is Off attached The port is operating in full duplex mode SIBI Collision of packets occurs orange Off The port is in half duplex mode or no device is Port Status Port 1 to 4 attached A network device is detected Blinking The port is transmitting or receiving packets from green the TX device Off No device is attached There are 7 diagnostic LEDs and 12 Port LEDs located on the Front panel of JetNet 3008 Industrial Ethernet Rail Switch These LED indicators provide administrators with real time system status The table below gives descriptions of the function of each LED indicator n Off No power is being supplied Off No power is being supplied PWR 2 Off No power is being supplied Off No power or UTP port or fiber port failure occurs A network device is detected LNK ACT of Port 7 8 Blinks The port is transmitting or receiving packets from th
10. cation of JetNet 3000 Series Industrial 5 port 8 port Entry Level Ethernet Rail Switch Data collect Server 100Base TX Fast Ethernet Cat 3 5 UTP STP cable EXTXXYXT XXX tirtiiriri mmm E Enterprise H UHHEHHEHIE E x management Interface 100Base TX Fast Ethernet Cat 3 5 UTP STP cable Field management 100Base TX Fast Ethernet Cat 3 5 UTP STP cable Programmable Logic Controller Distribute I O Control System Serial Device Server t Field Automatic device Field Automatic device Field Automatic device Take your JetNet 3005 3008 3005f Industrial 5 port 8 port Entry Level Rail Switch out of the package box 2 Check if the DIN Rail clip is attached to the JetNet 3005 3008 3005f If the DIN Rail clip is not attached to the JetNet3005 refer to DIN Rail Mounting section for DIN Rail installation If you want to wall mount the JetNet 3005 3008 refer to Wall Mounting section for wall mounting installation 3 To place the JetNet 3005 3008 3005f on the DIN Rail track or wall refer to the Mounting Installation section 4 Pullthe terminal block off the JetNet 3005 3008 3005f and wire the power lines Refer to the Wiring the DC Power Inputs section for how to wire the power inputs 5 PWR1 and PWR dual power inputs can be connected to power sources simultaneously When the primary power source fails the default setting is PWR1 the system will automatically switch to the secondary power source PWR2
11. cations ensuring customers a cost effective safe and reliable industrial applications JetNet 3005f supports fiber connectors effectively extending switches transmission distance Product Features Korenix JetNet 3000 Series products have the following features 5 port 8 port 10 100T X industrial switch for JetNet 3005 3008 4 port 10 100T X and 1 port 100F X for JetNet 3005f Supports store and Forward switching architecture Supports IEEE 802 3 10Base T 802 3u 100Base TX and 100Base FX standard Supports auto MDI MDI X function Embedded memory gt JetNet 3005 3005f 512 KB gt JetNet 3008 1024 KB Supports IEEE 802 3x flow control Flow control for full duplex mode Back pressure for half duplex mode Provides redundant dual power inputs Aluminum case with IP30 protection MAC address table gt JetNet 3005 3005f 1K gt JetNet 3008 2K B DIN Rail and wall mountable design Package Checklist Korenix JetNet 3000 Series products are shipped with the following items mM JetNet 3000 Industrial Entry Level 5 port 8 port Ethernet Rail Switch B One DIN Rail clip attached with the JetNet E One wall mounting plate and six screws Ba Users manual CD ROM B Quick Installation Guide If any of the above items is missing or damaged please contact your local sales representative 1 2 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 2 Hardware Installation This chapter includes
12. e TX device Off No device is attached 2 4 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Hardware Installation The port is operating in full duplex mode Collision of packets occurs The port is in half duplex mode or no device is FDX COL of Port 7 8 attached Collision of packets occurs The port is in half duplex mode or no device is Off attached The port is operating in full duplex mode SAHEN Collision of packets occurs orange Off The port is in half duplex mode or no device is Port Status Port 1 to 6 attached A network device is detected Blinking The port is transmitting or receiving packets from green the TX device No device is attached DIP Switches Fiber Port Fiber Half duplex mode JetNet 3005f Fiber Full duplex mode Default There is a set of DIP Switches located on the front panel of JetNet 3005f This set of DIP owitches is for configuring the fiber port s transmission modes full half duplex Note If two 3005fs are up linked with each other through fiber ports the communication speed would be slow if one JetNet3005 is configured to be full duplex mode and the other one is configured to be half duplex mode To obtain stable communication quality be sure the DIP switch is setting in same mode and have executed system power rest to perform it exactly 4 10 100TX 100FX 1 DIP Switches Korenix JetNet 3000 Series Industrial Entry Level
13. information of installation and configuration The following topics are covered in this chapter B Introduction Panel Layout Dimensions LED Indicators DIP Switches Wiring the Power Inputs Wiring the Ethernet Ports Wiring the Fiber Ports Cabling DIN Rail Mounting Installation Wall Mounting Installation Introduction Panel Layout JetNet 3005 Front View 1 LED indicators 2 RJ45 Ethernet ports JetNet 3008 Front View 1 LED indicators 2 RJ45 Ethernet ports 2 2 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Hardware Installation JetNet 3005f Front View 1 LED indicators 2 RJ45 Ethernet ports 4 3 Fiber Port 4 DIP Switch 3 A 2 Bottom View The bottom view of the JetNet 3000 o00OoOo0Q0000000000 1 Industrial Entry Level 5 port 8 port OOOOOOOOOOoOooooo Ethernet Rail Switch consists of one OOOOOOOOOOOOOO0 terminal block connector with two DC DC IN PWR power inputs and one DC IN power rui jack for an additional AC DC power adapter Power Input 12 48VDC v2 V2 N A V1 V1 Dimensions JetNet 3000 Industrial Entry Level 5 port 8 port Ethernet Rail Switch dimensions W x H x D are 54mm x 135mm x 105mm LED Indicators There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of JetNet 3005 3005f Industrial Ethernet Rail Switch These LED indicators provide administrators with real time system status The ta
14. lip reverse step 1 DIN Rail Clip Follow the steps below to mount the JetNet to the DIN Rail track 1 First insert the upper end of the DIN Rail clip into the back of the DIN Rail track from its upper side Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 2 7 3 nnd LT Reena eee errr eee eee eee ee ee a b ni puu P mnn a n d B n M ST Check if the DIN Rail clip is tightly attached on the track 4 To remove the JetNet from the track reverse the steps above Wall Mounting Installation Follow the steps below to install the JetNet with the wall mounting plate 1 2 3 4 5 To remove the DIN Rail clip from the JetNet loosen the screws from the DIN Rail clip Place the wall mounting plate on the rear panel of the JetNet Use the screws to tighten the wall mounting plate onto the JetNet Use the hook holes at the corners of the wall mounting plate to hang the JetNet onto the wall To remove the wall mounting plate reverse the steps above 2 8 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Hardware Installation Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 2 9 Installation and Testing The following figure illustrates a typical appli
15. ort on your JetNet 3005f to another one located on another JetNet follow the figure below Wrong connection will cause fiber ports not to work normally 2 6 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual Hardware Installation SC Connector Cable Wiring SC to SC TX A A RY RX B B TX JetNet fiber models have two 100Base FX ports with SC type connectors Fiber segment using single mode must use 8 125 or 9 125 um single mode fiber cables For single mode the connection distance can be up to 30 km Fiber segment using multi mode must use 50 or 62 5 125 um multi mode fiber cables For single mode the connection distance can be up to 2 km Cabling The cable connection between the JetNet 3005 3008 and the attached devices switches hubs workstations etc must be less than 100 meters 328 ft long The fiber cable connection between the JetNet 3005f and the attached devices switches hubs workstations etc must be less than 2000 meters long with multimode and 30000 meters with single mode DIN Rail Mounting Installation The DIN Rail clip is already attached to the JetNet 3000 Series products when packaged If the DIN Rail clip is not screwed on the JetNet follow the instructions and the figure below to attach the DIN Rail clip to the JetNet 1 Use the screws to attach the DIN Rail clip to the rear panel of the JetNet 2 To remove the DIN Rail c
16. t 23 Click on Computer A s dial out manager and change the modem s setting from dial up to dial in Follow this procedure to finish each modem s setting The industrial network is now established successfully Computer A is able to connect several converters using over the Ethernet via JetNet 3005 Industrial 5 port Entry Level Ethernet Rail Converter providing a reliable network environment 2 12 Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch User s Manual 3 Troubleshooting This chapter includes the information on general troubleshooting Make sure you are using the correct VDC power suppliers 12 to 48 VDC or power adapters Do not use power adapters with DC output over 48V It will damage devices Select Ethernet cables with specifications suitable for your applications to set up your systems Ethernet cables are categorized into unshielded twisted pair UTP and shielded twisted pair STP cables Category 3 4 5 Ethernet cables are suitable for systems with 10 Mbps transmission speed For systems with 100 Mbps transmission speed Category 5 Ethernet cables are the only suitable specifications for this environment You also need to make sure that the distance between each node cannot be longer than 100 meters 328 feet IF the power indicator does not turn on when the power cord is plugged in you may have a problem with power cord Than check for loose power connections power losses or surges at
17. xs seeks a taes aka vp udi x x Esas ma eu pL Ev r A e Peau apu 2 10 Chapter 3 Troubleshooting EON E ETE 3 1 Appendp A SpecificallOHls iudi deco uei cs s ep diaaa aia a deiae daai ahaa adaa aE A 1 Appendix B REVISION HISIOLY soiuri inana aa eneces echt B 1 1 Introduction Welcome to Korenix JetNet 3000 Series Industrial Entry Level Ethernet Rail Switch JetNet 3000 Series includes 3 models JetNet 3005 JetNet 3008 and JetNet 3005f JetNet 3000 Series is an entry level rail switch that is specially designed for industrial applications The following topics are covered in this chapter B Overview B Product Features B Package Checklist Overview Industrial environments are usually more demanding than office environments Harsh temperature conditions vibration dust etc all put a test on the quality and reliability of your switches To survive harsh industrial environments Korenix provides you with JetNet 3000 Series an Industrial 5 8 port with a fiber port Entry Level Ethernet Rail Switch JetNet 3000 Series Industrial Entry Level 5 port 8 port with a fiber port Ethernet Rail Switch is a cost effective solution ideal for your industrial applications in harsh environments JetNet 3000 Series not only gives you high speed data transmission over an Ethernet network but also provides redundant power inputs and reverse polarity protection In addition JetNet 3000 uses an IP30 aluminum case and has passed several safety certifi
Download Pdf Manuals
Related Search