1.3 technical features
Contents
1. 3 Control Box 4 Photo Sensor 5 24V DC gate opener 6 Transmitter DIMENSION CHART Comply with the measures shown on the chart for proper installation Adjust the gate structure to fit it for best automation if necessary Before preceding the installation be sure that gate moves freely and that 1 Hinges are properly positioned and greased 2 No obstacles in the moving area 3 No frictions between two gate leafs or with the ground while moving SER 140 150 10 180 200 210 2 MASTIFF 300 300M SWING GATE OPENER USER MANUAL MOTOR FIXING Assemble the rear bracket and fix it on the pillar Remove the wire cover and fix the rear bracket with the pin Release the gate opener and place the pin into the fitting position no 1 and no 2 Make sure the gate openers are mounted in horizontal position especially in those positions 1 Gate in CLOSE position 2 Gate in OPEN position 3 Gate at 45 angle position Prior to weld the bracket on the gate leaf if necessary cover the gate opener to prevent damages from sparks TO CONNECT MASTIFF WITH CONTROL UNIT Standard MS Motor With Hall Sensor ss ENE EE a s CORRESPONDING CONTROL SYSTEM Standard MS Motor With Hall Sensor CB16 CB17 CB30 CB20 MS Mechanical Stopper 2 Always connect the grounding wire GND MASTIFF 300 300M SWING GATE OPENER USER MANUAL E EMERGEN2. CY RELEASE In case of power failure push the lid of release chamber and move forward Insert the key and turn clockwise to unlock then turn around the knob to release To restore the automation simply reverse the above procedures Step1 Push the lid of release chamber and move forward Step2 Insert the key and turn clockwise to the unlock position Step3 then turn clockwise the knob to release the motor Make sure the White bar on the knob is on the position opposite to the triangle indication To restore the automation simply reverse the above procedure E MECHANICAL STOPPER ADJUSTMENT Adjust for the mechanical stopper follow the below steps Step1 Remove the screws on both side of the motor cover Step2 Push the front external tube forward separate from the motor base Step3 Release the screw on the mechanical stopper to change the position The position of the front and rear mechanical stopper indicates the Open Close position of the gate 4 MASTIFF 300 300M SWING GATE OPENER USER MANUAL 1 3 TECHNICAL FEATURES A Technical Feature Motor 24Vdc motor with mechanical release Gear Type Worm gear Max Absorbed Power 144W Peak Thrust 3000N Nominal Thrust 3000N Stroke Length 350mm Power Supply 24Vdc Nominal Input Power 2 Maximum Operating Current 5 5A for maximum 10 seconds Maximum Gate Weight 300 kg per leaf Maximum Gate Length 3 meters Duty Cycle 20 Operating Temperature 20 C 50 C Dim
3. MASTIFF 300 300M SWING GATE OPENER USER MANUAL E Ge 1 1 1 2 1 3 1 4 INDEX GENERAL SAFETY PRECAUTION 0000002 P 1 INSTALLATION n I a 1 A STANDARD DIMENSION CHART 2 MOTOR FIXING mmm enn D WIRE CONNECTION katte E EMERGENCY RELEASE P 4 F MECHANICAL STOPPER 5 TECHNICAL FEATURES 0000000 P 6 A TECHNICAL FEATURES i ta pa pid leo Pali haa kh P 6 B DIMENSION aria at alea ia minia kail P6 MAINTENANCE 0 P6 1 1 GENERAL PRECAUTION WARNING This user manual is only for qualified technicians who is specialized in installations and automations 1 All installations electrical connections adjustments and testing must be performed only after reading and understanding of all instructions carefully 2 Before carrying out any installation or maintenance operation disconnect the electrical power supply by turning off the magneto thermic switch connected upstream and apply the hazard area notice required by applicable regulations 3 Make sure the existing structure is up to standard in terms of strength and stability 4 When necessary connect the motorized gate to reliable earth system during electricity connection
4. ension 837mm 123mm 124mm Weight 6 6kg B Dimension pO GI 1 4 MAINTENANCE Conduct the following operations at least every 6 months If in high intensity of use shorten the period in between Disconnect the power supply 1 Clean and lubricate the screws the pins and the hinge with grease 2 Check the fastening points are properly tightened 3 Make the wire connection are in good condition Connect the power supply 1 Check the power adjustments 2 Check the function of the manual release 3 Check the function of photocells or other safety devise MASTIFF 300 300M SWING GATE OPENER USER MANUAL Key Release EZ Instal Low Voltage Durability 24V power supply Solid material apply Manual release device Worm gear application Easy installation for great safety with lasting usage with easy use and give silence operation and user friendly highly protection interface G 34100 089 A
5. phase 5 Installation requires qualified personnel with mechanical and electrical skills 6 Keep the automatic controls remote push bottom key selectors etc being placed properly and away from children 7 For replace or repair of the motorized system only original parts must be applied Any damage caused by inadequate parts and methods will not be claimed to motor manufacturer 8 Never operate the drive if you have any suspect with what it might be faulty or damage to the system 9 The motors are exclusively designed for the gate opening and closing application any other usage is deemed inappropriate The manufacture should not be liable for any damage resulting from the improper use Improper usage should void all warranty and the user accepts sole responsibility for any risks thereby may accrue 10 The system may only be operated in proper working order Always follow the standard procedures by following the instructions in this installation and operating manual 11 Only command the remote when you have a full view of the gate TMT AUTOMATION INC shall not be liable for any injury damage or any claim to any person or property which may result from improper use or installation of this system Please keep this installation manual for future reference MASTIFF 300 300M SWING GATE OPENER USER MANUAL 1 2 STANDARD INSTALLATION A STANDARD INSTALLATION 1 24V DC Flashing Light 2 Push Button
Download Pdf Manuals
Related Search