User Manual - Infrared Heater Model 60803
Contents
1. Distributed by Well Traveled Living Amelia Island FL 32034 Web www wtliving com Email cservice welltraveled net wy or aaa ae ae Owner s Manual Model 60803 READ amp SAVE these instructions Carefully read and review before attempting to assemble install operate or maintain this product Observe all safety instructions and information FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY For Residential Use Only Important Notice Do not return to place of purchase Please contact our Toll Free Hotline at 1 866 985 7877 for customer service and warranty issues SAVE THESE INSTRUCTIONS C Intertek 3154846 Safety Guidelines Read this manual carefully to become knowledgeable about your heater and how to use it properly To help recognize this information observe the following symbols DANGER A WARNING Indicates a potentially hazardous situation which if Indicates a potentially hazardous situation if not not avoided WILL result in serious injury or death avoided COULD result in serious injury or death CAUTION NOTICE Indicates a potentially hazardous situation which if Indicates important information that if not followed not avoided MAY cause moderate injury or damage to may cause damage to the equipment the equipment DANGER 1 l 5 Risk of Fire There is always2. Unit Dimensions 25 6 x 21 6 x 18 1 Heater Assembled Dimensions 15 75 diameter base 95 height Storage Always UNPLUG the unit when not in use Once the head unit has completely cooled store the heater with the protective vinyl cover on the head unit When heater is not in use for an extended period of time store in a covered location that is dry and out of the weather Make sure the heater is stored in a location that is out of the way of people and pets that may accidentally knock the heater over or damage the appliance Before storing the heater make sure the electrical cord is coiled and out of the way When storing ALWAYS lower the telescopic pole to its lowest level This will make it easier to store and reduce the risk of any accidental tipping over of the heater Maintenance Your Infrared Heating System is virtually maintenance free A minute to wipe down exposed surfaces is all it takes to maintain your heater Head unit and shield Use a non abrasive cleaner and a soft cloth to wipe off debris and dirt from the exposed surfaces NEVER spray liquids or cleaners into the housing area where the halogen lamp is located Do not try to disassemble of clean the inner cavity where the halogen lamp is located For any maintenance on the head unit please call the toll free customer service hotline Telescopic pole and curved arm components These can easily be wiped clean using a non abrasive cleaner and a s
3. 2 Using Mounting bracket Part 2 thread entire electrical cord through the Mounting bracket as shown in Figure 2 FIGURE 2 STEP 3 Use 4 M6 12 Oval head screws Hardware A to attach Mounting bracket Part 2 to head unit Part 1 as shown in Figure 3 FIGURE 3 STEP 4 Align tilt switch black box on head unit Part 1 to threaded holes on Mounting bracket Part 2 and insert M4 10 Round head screws Hardware C with M4 Flat washers Hardware B as shown in Figure 4 FIGURE 4 STEP 5 Attach Round end bracket Part 7 to Upper support tube section Part 3 with 4 M6 12 Oval head screws Hardware A as shown in Figures 5 and 6 FIGURE 6 STEP 6 Attach Top cover finishing piece Part 6 to Upper support tube section Part 3 with 4 M6 12 Oval head screws Hardware A as shown in Figure 7 FIGURE 7 STEP 7 Attach L shaped bracket Part 8 to Upper support tube section Part 3 with 2 M6 20 Oval head screws Hardware G as shown in Figure 8 FIGURE 8 STEP 8 Thread electrical cord through assembled Upper support tube section Part 3 as show in Figure 9 FIGURE 9 STEP 9 Attach assembled Upper support tube section Part 3 to Mounting bracket Part 2 with 4 M6 12 Oval head screws Hardware A as shown in Figure 10 A FIGURE 10 STEP 10 Locate Telescopic Body section 4 2 NOTE It has a small machined hole at the bottom of the section see Figure 11 and slide A
4. a risk of fire when working with a heater Keep it away from flammable liquids and any material that could easily catch fire 2 b Risk of Fire If the heater falls this unit might start a fire IN 3 da Hot or Burn Hazard This unit may be hot at any time during its use especially around the head and heating element 4 Electrical Hazard Disconnect all electric power before working on the unit There is a chance of electric shock if you work on this unit with it still plugged into the wall A cord has been damaged Electric Shock This unit uses electricity to operate Do not use this heater around water or if the CAUTION e Improper treatment of the heater can damage it and also shorten its life span e To prevent electrical shock follow electrical plug requirements on page 11 of this manual This appliance MUST be grounded When using outdoors we recommend using a certified GFI Ground Fault Interrupt outlet to protect against electrical shock All installations must be in accordance with I E E safety regulations or the equivalent l i l Avoid the use of an extension cord with this appliance ACAIN Do not place any objects such as furniture papers clothing or curtains closer than 3 feet to the front and sides of the heater PARTS LIST 1 IR Head unit w Protective Shield with Tilt Switch safety cut off On Off Switch PULL for ON PUSH for OFF Angle Adjustment Bar 1500 W
5. att quartz halogen bulb Swivel Bracket 15 5 foot 14 AWG grounded electrical 2 Mounting Bracket attaches head unit to telescopic pole 3 Upper support tube section for telescopic body 4 Telescopic Body includes 2 sections 4 1 and 4 2 with 2 easy release clamp collars 4 3 to allow for easy adjustment 5 Adjustable table 6 Top cover finishing piece 7 Rounded end bracket 8 L shaped bracket 9 Support Collar for telescopic body 10 Base assembly with wheel assembly 11 Protective vinyl cover for use ONLY when heater has completely cooled 11 ALSO INCLUDED not pictured Hardware packet B M4PlatWasher 2 pieces D M8 22 Hexagon Screw 4 pieces E M8 FlatWasher 4 pieces F M620 Oval Head Screw 2 pieces G M8 16 Hexagon Screw Important Instructions 10 Read all instructions before using this heater This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Keep combustible materials such as furniture pillows bedding papers cloths and curtains at least 3 feet 0 9m from the front sides and rear of the heater DO NOT leave heater unattended Extreme caution 1s necessary when any heater is used by or near children or disabled persons and whenever the heater is left operating and unattended Always unplug heater when not in use Do not operate any heater with a damaged cord or plug if th
6. djustable Table Part 5 over the end of section 4 2 making sure the adjustable clamps on the table are facing DOWN SMALL HOLE FIGURE 11 Now locate Telescopic Body section 4 1 NOTE It has a large round hole at the bottom of the section see Figure 12 and slide section 4 1 down into section 4 2 until you can see the small machined hole from section 4 2 through the large round hole at the bottom of section 4 1 as shown in Figure 13 Insert 1 M4 10 Round Head Screw into the small hole and tighten This will prevent section 4 2 from sliding completely out of section 4 1 when the assembled pole is lifted FIGURE 13 Insert screw here and tighten LARGE HOLE FIGURE 12 STEP 11 Thread electrical cord from Upper support tube section down through Telescopic body Part 4 2 and Telescopic body Part 4 1 as shown in Figure 14 FIGURE 14 STEP 12 Attach wheel assembly to base assembly with 3 M8 16 Hexagon screws Hardware I Mount Support collar flange Part 9 to Base assembly with wheels Part 10 as shown in Figure 15 and secure with 4 M8 22 Hexagon screws Hardware D and 4 M8 Flat Washers Hardware E 4 BN FIGURE 15 10 STEP 13 Thread electrical cord through Support collar for telescopic base Part 9 and Base assembly Part 10 and out of the hole on the Base assembly as shown in Figure 16 FIGURE 16 STEP 14 Carefully lift assembled pole and head unit and insert
7. e heater malfunctions or has been dropped or damaged in any manner Return heater to authorized service facility for repairs Heater can be used indoors or outdoors Operate a minimum of 3 feet 0 9m from people or objects Never operate heater near water or where it can be knocked over Do not run cord under carpeting Do not cover cord with throw rugs runners or similar coverings Arrange cord away from traffic area and where it will not be tripped over To disconnect heater switch to OFF position push in switch located on head unit and then remove plug from electrical outlet Connect to properly grounded outlets only 11 Do not insert or allow foreign objects to enter any ventilation or exhaust opening doing so may cause an electrical shock or fire or may damage the heater 12 To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked 13 A heater has hot and sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored 14 Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electrical shock or injury to persons 15 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire However if you must use an extension cord use either a 12 gauge or 14 gauge wire which i
8. imited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty 1IMIPORTANT NOTICE Do NOT return to place of purchase For customer service and warranty issues contact our Customer Service Center at 866 985 7877 OR Email cservice welltraveled net Customer Service Hours Mon Fri 9 00 a m 6 00 p m EST Fire Sense Mojave Sun and Well Traveled Living are registered trademarks of Well Traveled Imports Inc All assembly instruction presentations are the property of Well Traveled Imports Inc and are protected by U S copyrights and trademarks All rights reserved
9. lamp end connectors amp wire lead nc NOTE do NOT allow any metal to contact actual lamp tube 14 Troubleshooting Problem Unit fails to turn on Telescopic pole slips down Telescopic pole is unsteady Telescopic pole will not adjust Head unit is loose or unsteady Head unit is hard to adjust Smoke appears from head unit Weak output from halogen lamp Solution Check electrical plug connection at wall outlet for a complete snug fit Check to make sure the On Off switch located on tilt switch is pulled OUT or in the On position Check GFI and reset circuit breaker if needed If unit is plugged into a wall outlet wired to an On Off switch make sure switch is in On Position Reset safety tilt switch Unplug unit from wall outlet and re position on flat level surface Plug heater back into outlet Damaged halogen bulb Call customer service hotline Tighten black tension knobs on clamp collars Tighten screws on support collar at base Electrical cord may be kinked Gently pull end of cord until taut Tighten screws on mounting bracket Loosen connecting bolts nuts at adjustment bracket Unplug IMMEDIATELY and call customer service hotline Life span of lamp has been reached or damaged lamp Call customer service hotline for assistance NOTE This product comes with a limited one year warranty After the warranty period you may purchase replacement bulbs from www patiomarket com a
10. lower end of pole into Support collar Part 9 as shown in Figure 17 Secure with 8 M6 12 Oval head screws Hardware A FIGURE 17 11 OPERATING INSTRUCTIONS This appliance MUST be grounded CAUTION When using outdoors we recommend using a certified GFI Ground Fault Interrupt outlet to protect against electrical shock ALL installations must be in accordance with I E E safety regulations or equivalent Avoid the use of an extension cord with this appliance If one is used it must meet the requirements as outlined in 15 Important Instructions on page 4 of this manual Do not place any objects such as furniture papers clothing or curtains closer than 3 feet to the front top or sides of this heater ALWAYS unplug the heater when it is not in use For optimal performance and safety concerns we HIGHLY recommend that the Infrared Heating System be operated at a minimum of 95 in height or the maximum extended length of the telescopic body sections You should only lower the height of the unit for storage purposes when it has completely cooled and is not in operation To adjust the IR telescopic body Pull up on the release levers of the tightening clamps and adjust tension using the tension knobs Raise and lower the telescopic sections and or swivel to desired position and then push in clamp levers to secure DO NOT over tighten tension knobs There should only be a moderate amount of tension to main
11. oft cloth Base with wheel assembly Use non abrasive cleaner and a soft cloth Any scratches chips or rust spots can be touched up using an exterior matte finish paint 13 Halogen Lamp Replacement Contact the toll free customer hotline to order approved replacement lamps and parts Use ONLY approved original equipment and replacement halogen lamps to ensure safe proper and maximum output operation of your heater NOTE Do NOT touch the new halogen lamp with your bare fingers Oils from your hand could reduce the life of the lamp by causing a heat spot We recommend using clean cotton or plastic gloves to handle the lamp A clean paper towel will also work MAKE SURE THE HEATER IS TURNED OFF AND DISCONNECTED FROM THE ELECTRICAL OUTLET BEFORE YOU BEGIN TO REPLACE THE HALOGEN LAMP 1 Be sure the heater is unplugged from the wall outlet Remove the head unit assembly from the telescopic pole 2 Remove 8 screws from each end of the head unit and pull off end plates 2 Note the placement of the 2 small sheet metal screws on each end plate Also note end plate side with beveled holes faces outward when re assembled 3 Pull out and remove the left and right front air vent panels and protective wire grill 3 Note the position of end clips on vent panel They must be aligned as close to the end connectors of lamp tube as possible when re assembled Pull or push into place as needed DO NOT allow metal parts to touch the actual lamp tube
12. om accident negligence misuse abuse neglect mishandling alteration or modification failure to maintain improper assembly or maintenance service by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED ABOVE PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY IN NO EVENT WILL WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL WELL TRAVELED LIVING OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER This l
13. s rated not less than 1900 watts The recommended length for a 14 gauge is 0 50 feet but if you must use a longer cord use a 12 gauge NO LONGER than 100 feet This unit comes equipped with a Safety Tilt Switch mechanism Power will shut off automatically should the unit be accidentally knocked over or tilted past 15 degrees To reset unplug the unit from wall outlet reposition on a flat level surface and plug in again SAVE THESE INSTRUCTIONS for future reference Please keep each side of the head unit at least 11 8 inch from the objects see below Assembling Your Heater Before beginning assembly be sure to read and familiarize yourself with the overall assembly process and instructions in this manual It may be helpful to have someone assist you with the assembly You will need the following tools NOT INCLUDED 2 Or 3 Philips Screwdriver or standard slotted screwdriver Adjustable Wrench Make sure you complete assembly on a clean level preferably carpeted location A flat piece of cardboard will also work for assembly Unpack and identify all components listed on page 3 of this manual and lay them out on the carpeted floor or piece of cardboard and then follow the steps below STEP 1 Loosen and remove the top 2 Tapping screws on each side of the head unit Part 1 and attach the angle adjustment handle included with Part 1 as shown in Figure 1 Tighten the screws i b g FIGURE 1 STEP
14. t the lowest cost available 15 Distributed By Well Traveled Living 716 S 8 Street Amelia Island FL 32034 Toll Free 866 WTL SUPP Web www wtliving com Email cservice welltraveled net 1 YEAR LIMITED WARRANTY Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use This warranty does NOT cover normal wear and weathering assembly and or maintenance OR use in a commercial application At Well Traveled Living s sole discretion products under warranty will be repaired and or replaced at no charge to the customer Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging For warranty service contact Well Traveled Living at the address phone numbers or internet site and email listed in this owners manual Be sure to have your sales receipt date of purchase and catalogue model numbers available when calling All warranty service will be coordinated by the Well Traveled Living s Amelia Island Florida service center This warranty is extended only to the original purchaser Proof of purchase will be required before warranty service is rendered The sales receipt is the only valid proof of purchase This warranty only covers failures due to defects in materials or workmanship which occur during normal use Failures and or damage which result fr
15. tain the telescopic position of your heater Step 1 Before turning on your Infrared Heating System check to make sure the On Off switch located on the tilt switch black box of the head unit is pulled OUT or in the ON position note to turn the heater Off push in the switch Next extend all 3 telescopic sections to their maximum extended length Release clamp levers and pull up on each of the sectional steel tubes until each tube stops Then push in clamp levers to secure sections in place Adjust the tension knobs as needed to maintain height position Step 2 The Infrared Heating System comes equipped with a heavy duty 14 AWG gauge wire Grounded guile Dox Over and grounded plug This appliance must be used with an outlet that has been installed and grounded in accordance with local codes and ordinances Make sure the heater 1s connected to an outlet having the same configuration as shown in the figure shown to the right DO NOT use an adapter with this product Check with a licensed electrician if the grounding instructions are not understood completely or if the wall outlet does not match the plug Step 3 Your Mojave Sun Infrared Heating System is ready to enjoy Plug the appliance in and enjoy the warmth 12 Specifications Model 60803 Voltage 120 volts Amps 12 5 amps Wattage 1500 watts Lamp Type Quartz Halogen Minimum Operational Height 7 ft 11 in 95 in Assembled Weight 69 Ibs Head
16. when re assembled 4 Gently pull out entire old lamp assembly from the clips at the terminal connection ends 4 amp 5 Slide and lift the connection ends out from the friction clips by gently pushing apart the clips Unscrew wire leads from terminal Remove entire old lamp assembly 5 Using gloves gently re insert connection ends of the NEW lamp assembly into the friction clips 4 Pull apart the clips slightly and gently push the connectors into place Do not allow the metal clips to touch the lamp tube The clips should be about at the center point of the end connectors 6 Re install the safety grill fits along grooves in housing body then re insert the vent panels by gently pushing the end clips into housing body Align clip ends close to the lamp end connectors and push into place Re attach end plates making sure the side with beveled holes faces out 5 lamp assembly Clip ends must be aligned as Close to end connectors of lamp tube when installed Do NOT allow to touch tube lamp itself Using gloves gently re insert connector ends of the NEW Metal friction chps lamp assembly into the friction Push apart siigtly clips see 4 Pull apart the clips slightly and gently push the connectors into place Do not allow the metal clips to touch the actual lamp tube The clips should be about at the center point of the end connectors when i re assembied i Front Vent P Remove amp Replace ENTIRE Lamp assembly iuding
Download Pdf Manuals
Related Search