Home

AFL2-12A-HM65 Panel PC User Manual

Contents

1. 65 Series Flat Bezel Panel PC with Intel Sandy Bridge Mobile CPU TFT LCD Wi Fi Touch Screen RFID Reader GbE LAN RS 232 422 485 Camera RoHS User Manual GI Rev 1 11 8 August 2013 E integration Corp AFL2 12A HM65 Series Panel PC Revision Date Version changes O O O 8 August 2013 1 11 Added information of the CPU temperature alert LED in Section 1 2 1 1 10 July 2012 1 10 Updated for R11 remove second LAN function 8 December 2011 1 00 Initial release AFL2 12A HM65 Series Panel PC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer TRADEMARKS All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective
2. Integration Corp AFL2 12A HM65 Series Panel PC T ET 19 Ded STE POW ER eevee TTT 19 ZI PPM 19 2 7 1 1 ATX Power Mode ER E e WE 20 2 EN POW le 20 EE EE 20 SR E Se i IL E 21 E NPACKINO cio ri 22 SSL a ai 22 MINTS KH B DN ER L ME 26 4 1 ANTI STATIC PRECAUTIONS see eee 27 4 2 INSTALLATION PRECAUTIONS ccccccccccccccccsccsssssssssssssseesccccceceeccssceeeaenssssssseeeseceeeees 2 4 3 INSTALLATION AND CONFIGURATION STEPS sss sees 28 ADD ENS A ATION eroina aria Rap E aa tare 28 A D ATATX MODE EE ee 31 4 5 1 AT Power FA 32 POL ALA FOW T M O Caeira E E ane ee ee ee 32 EREECHEN 33 4 7 POWERING OFF THE SYSTEM sese 33 4 0 MOUNTING THE SYSTEM T 33 LOL ere 34 VIVO RR RIA 37 AOS AT MOUINE iO TATA 37 4 8 4 Cabinet and Rack Installation 38 4I BOTTOM IP ANELAC OC 4 DT LAN CONNEC OW iena 41 K SONALDEVICECOMECNODI ssaa slider 4 4 9 2 1 DB 9 Serial Port Connection 42 4 9 2 2 RJ 45 Serial Port Comme ction ccssssscscccccssccesssesscccccsseceessesssccecsseees 42 4 9 3 RS 422 485 Serial Port Connection 44 4 9 4 USB Device Connection sss seene 46 4 9 5 HDMI DEVICE E 47 EV BN EN TOR K ONE SL 6 Ea 49 Page VI AFL2 12A HM65 Series Panel PC 5 1 SYSTEM MAINTENANCE INTRODUCTION sese 50 NZANTESTIATIGERECALTIONS ira tn 50 IS EECHER SI IFOPENNO THESE EE 51 Debt Kemovin Ine BaCk C OVET ropisi E eeanee cameo caenmnnemo SI 5 4 2 Removing the Internal Aluminum Cove
3. Integratio AFL2 12A HM65 Series Panel PC Modify image comment One Key Recovery path share image browseable yes writable yes public yes create mask 0644 directory mask 0755 Step 4 Edit etc samba smb conf for your environment For example security user is always a good idea This will require a Unix t in this server for every user accessing the server See 4 fusrishare doc sanba_docthtnldoce Samba3 HOWTO S serverl ype html t in the samba doc package for details security share image comment Une key Recover o path Share image brovseable yes writable yes publi ic ves create mask 0644 directory nas ak 0755 Step 5 Modify the hostname vi etc hostname Modify RecoveryServer D 6 6 Setup a Client System for Auto Recovery Step 1 Configure the following BIOS options of the client system Advanced gt iEi Feature gt Auto Recovery Function gt Enabled Advanced Ei Feature gt Recover from PXE gt Enabled Boot gt Launch PXE OpROM Enabled Page 165 Integration Corp AFL2 12A HM65 Series Panel PC Step 2 Continue to configure the Boot Option Priorities BIOS option of the client system Boot Option 1 gt remain the default setting to boot from the original OS Boot Option 2 gt select the boot from LAN option Step 3 Save changes and exit BIOS menu Exit gt Save Changes and Exit Step
4. 11rrrrssiriiieeiiiiin 142 Recovery TOO Menu aiar 142 About Symantec Ghost WindoW rrrrrreeee eee 143 Svmantec Ee CA sssi eea a aaaea 143 Select a Local Source Drive ccccceeeecccsssssseeeeeeseeeeeneseeeeeeecessseeeeeeeseoeensnes 144 Select a Source Partition from Basic Drive 1rrrrrrrrreseeeenananao 144 File Name to Copy Image NO sssssssssssssssssssssssssssssse enen nenen nenen 145 Compressimage cina 145 image Creation Confirmation sesivicesceceseccentincxscesecivesvidenwcecetievessadsacacesavexeswewewewenes 146 Image ei Cie E aaa 146 Image Creation Complete iii 146 Press Any Key to Continue siii 147 Auto Recovery NING seisin a aeaa 148 Launching the Recovery TOOl 111 22rrrrrrsseeirerie zizi ii erre siii iieeienini 148 Figure D 24 Figure D 25 Figure D 26 Figure D 27 Figure D 28 Figure D 29 Figure D 30 Figure D 31 Figure D 32 Figure D 33 Figure D 34 Figure D 35 Figure D 36 Figure D 37 Figure D 38 Figure D 39 Figure D 40 AFL2 12A HM65 Series Panel PC Auto Recovery Environment for WINdoWS rrrrreiiiziiiine 148 Building the Auto Recovery Partition ccccccccsesseeeeeeeeeseeeeeeeeeseeeeneeneeeeeeneaes 149 Factory Default Image Confirmation sssssssssssssssssss sees sss ees eenn eee 149 Image Creation ee e 150 Press any key to E ln TE 150
5. 1 rrrrrreiiiirii iii 37 Figure 4 11 Arm Mounting Retention Screw Holes rrrrrrrrseziizi siii iiieninn 38 Figure 4 12 The Rack Cabinet Bracket r rire 39 Figure 4 13 Secure the Rack Cabinet Bracket 22 1rrrrrrreniriiiiireei eee 40 Figure 4 14 Install into a Rack Cabinet rei 40 Figure 4 15 Renee d E 41 Figure 4 16 DB 9 Serial Port Connector 11rrrrrrssaiiziiiiii 42 Page X AFL2 12A HM65 Series Panel PC Figure 4 17 Ethernet eena e uri 43 Figure 4 18 RJ 45 Serial Port Connector xxssssssssaazazazaasszzzanazaz ana naazananinia 44 Figure 4 19 RS 422 485 Serial POW reni 44 Figure 4 20 RS 422 485 Cable nnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnna 45 Figure 4 21 DB 9 Connector E 45 Figure 4 22 USB Device e al Le H 47 Figure 4 23 HDMI Connec ON sauis Aaa A aa aE ea AAGA 48 Figure 5 1 Back Cover Retention SCrewsS ccccccssssssseeeeeeceesssseeeeeeeeeeenssneeeeeeeeeoeseeeeeeeseeooeaes 52 Figure 5 2 Internal Cover Retention SCreWwS cssssss sese esse eee esse eenn 53 Figure 5 3 DDR SO DIMM Module Installation 1rrs iii 54 Figure5 4 Removing the Antennas 11rs sr rr 55 Figures 5 Releasing the WLAN Cal ciccia ira 55 Figures 6 Removi
6. AFL2 12A HM65 Series Panel PC ca Windows System32 cmd exe 1 Factory Restore 2 Backup system 3 Restore your last backup 5 Quit Please type the number to select and then press Enter 1 Recovery complete Press any key to continue m Figure D 35 Recovery Complete Window D 5 2 Backup System To backup the system please follow the steps below Step 1 Type lt 2 gt and press lt Enter gt in the main menu Step 2 The Symantec Ghost window appears and starts to backup the system A backup image called iei_user GHO is created in the hidden Recovery partition Symantec Ghost 11 5 Copyright C 1998 2008 Symantec Corporation All rights reserved Type CHTFS 100006 AB 1951 HE used Ho name from Local drive 1 152627 HE Local file D iei_user gho Figure D 36 Backup System Step 3 The screen shown in Figure D 37 appears when system backup is complete Press any key to reboot the system Page 157 k WW Be d Corp N fre TEE integration P emm ae a x e e da ca Windows System32 cmd exe i Factory Restore 2 Backup system 3 Restore your last backup 4 Manual D Quit Please type the number to select and then press Enter 2 System backup complete Press to continue a Figure D 37 System Backup Complete Window D 5 3 Restore Your Last Backup To restore the last system backup please follow the steps below Step 1 Ty
7. 0 eee SS 5 S SZ Ss S o S n K gt B n cs 5 op 2 E DoF o 0 LL oc 53 gt c o K Y 5 s f lt cl 5 G I o Ss 2s ES E e M si o D OD RF 2 a W o e mM Ke lt gt st a O Figure 1 3 LED Indicators The descriptions of each LED indicator are listed below Shows power on off status AT ATX Mode Shows the power mode status Controlled by the AT ATX power mode switch CPU Temperature Alert BLUE CPU temperature is normal RED CPU core temperature reaches TJ Max Wi Fi The Wi Fi module is enabled or disabled Controlled by the BIOS See Section 6 5 1 1 RFID The optional RFID reader is enabled or disabled Controlled by the hot keys See Table 1 3 Bluetooth The Bluetooth module is enabled or disabled Controlled by the BIOS See Section 6 5 1 1 Auto Dimming The auto dimming function is enabled or disabled Controlled by the remote control Microphone The microphone is enabled or disabled Controlled by the BIOS See Section 6 5 1 1 integration Corp AFL2 12A HM65 Series Panel PC Audio Mute Lights on when the audio is turned off Controlled by the hot keys See Table 1 3 Function Shows the status of the function key below the LED indicator Blinks when the corresponding button is pushed LCD On Off Audio Volume Down Audio Volume Up Brightness Down Brightness Up Table 1 2 LED Indicators A WARNING When the CPU s core temperature reaches TJ Max the CPU tempe
8. AFL2 12A HM65 Series Panel PC 4 8 1 Wall Mounting To mount the flat bezel panel PC onto the wall please follow the steps below Step 1 Step 2 Step 3 Step 4 Step 5 ei Select the location on the wall for the wall mounting bracket Carefully mark the locations of the four screw holes in the bracket on the wall Drill four pilot holes at the marked locations on the wall for the bracket retention screws Align the wall mounting bracket screw holes with the pilot holes Secure the mounting bracket to the wall by inserting the retention screws into the four pilot holes and tightening them Figure 4 7 Figure 4 7 Wall mounting Bracket r e SS e A A E l Iintegrationi Corp AFL2 12A HM65 Series Panel PC Step 6 Insert the four monitor mounting screws provided in the wall mount kit into the four screw holes on the real panel of the flat bezel panel PC and tighten until the screw shank is secured against the rear panel Figure 4 8 A WARNING Please use the M4 screws provided in the wall mount kit for the rear panel If the screw is missing the thread depth of the replacement screw should be not more than 4 mm Step 7 Align the mounting screws on the monitor rear panel with the mounting holes on the bracket Step 8 Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes Figure 4 8
9. AFL2 12A HM65 Series Panel PC E ek Hardware and Eege 135 DACCI 135 D 2 3 Install Operating System Drivers and Applications iii 139 D 2 4 Building the Recovery EEN ege E EE 140 D2 AET E 142 D 3 AUTO RECOVERY SETUP PROCEDURE cccccecesesssssseeceeeeceeeessssseeeeeeeeeeeessssaaaes 147 Ee EREECHEN 151 D 5 RECOVERY TOOL FUNCTIONS eege ees 155 DILLO 156 DZ 157 D 5 3 Restore Your Last Backup sese eee 158 EEN 159 D 6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN ee 160 D 6 1 Configure DHCP Server Aetiuge sss 161 DOF COM E E H R A ice 162 D 6 3 Configure One Key Recovery Server Settings i 163 D 0 4 Startthe DHCP IFIP and OTIP eere a E a 164 DOS Cre E iii 164 D 6 6 Setup a Client System for Auto KecCduery sss 165 DFOLHERINFORMATRON ili ipa 168 D 7 1 Using AHCI Mode or ALi M5283 VIA VT6421A Controller 168 D 7 2 System Memory Requirement iii 170 EWArCHDOCG N HO RN 171 F HAZARDOUS MATERIALS DISCLOSURE scssrrrrrrrrerereseseseeeeeeeeeeeececeenecece 174 F 1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002 95 EC WITHOUT NIERCURY 175 Integration Corp AFL2 12A HM65 Series Panel PC List of Figures Figure 1 1 Figure 1 2 Figure 1 3 Figure 1 4 Figure 1 5 Figure 1 6 Figure 1 7 AFL2Z 12A HM65 Flat Bezel Panel PC 2 AFL2 12A HM65 Front TI 4 B i lege eS sce i
10. Page 136 AFL2 12A HM65 Series Panel PC ca CAWINDO WoSieyctem32 cmd B exe Execute Ghost Manual Recovery environment For Windows Manual Recovery environment For Linux i fiuto Recovery environment For Windows Exit Command Prompt ype the number to print dE A dE d Figure D 4 Command Prompt Step 5 N x E l Integrat The command prompt window appears Type the following commands marked in red to create two partitions One is for the OS installation the other is for saving recovery files and images which will be an invisible partition Press lt Enter gt after entering each line below system32 gt diskpart DISKPART gt list vol DISKPART gt sel disk 0 DISKPART gt create part pri size __ DISKPART gt assign letter N DISKPART gt create part pri size __ DISKPART gt assign letter F DISKPART gt exit system32 gt format N fs ntfs q y system32 gt format F fs ntfs q v Recovery y system32 gt exit Page 137 la Le ca 8 I1386system32 CMD EXE a 1386 SYSTEM32 diskpart Microsoft DiskPart version 5 2 379709 1835 Copyright lt C 19799 26061 Microsoft Corporation On computer MININT JUG DISKPART gt list vol Status Volume H A CD_ROM CDFS DUD ROM MB Healthy Volume 1 D FAT3Z Removeable 3854 MB Healthy DISKPART gt sel disk H Disk B is now the selected disk DISKPART gt create part pri size 2688 DiskPFart succeeded in
11. Figure 4 3 Removing the HDD Bracket Step 5 Insert an HDD into the bracket as shown Figure 4 4 Figure 4 4 Inserting the HDD AFL2 12A HM65 Series Panel PC Step 6 Secure the HDD to the bracket using four 4 retention screws two screws on each side Figure 4 5 Figure 4 5 Securing the HDD Step 7 Slide the HDD module back into the device Step 8 Tighten the captive screw Step 9 Replace the HDD cover and secure it using two 2 retention screws 4 5 AT ATX Mode Selection AT and ATX power modes can both be used on the AFL2 12A HM65 The selection is made through an AT ATX switch located on the I O panel Figure 4 6 To select AT mode or ATX mode follow the steps below Step 1 Locate the AT ATX switch on the I O panel Figure 4 6 AFL2 12A HM65 Series Panel PC Figure 4 6 AT ATX Switch Location Step 2 Adjust the AT ATX switch 4 5 1 AT Power Mode With the AT mode selected the power is controlled by a central power unit rather than a power switch The AFL2 12A HM65 panel PC turns on automatically when the power is connected The AT mode benefits a production line to control multiple panel PCs from a central management center and other applications including ATM Self service kiosk Plant environment monitoring system Factory automation platform Manufacturing shop flow 4 5 2 ATX Power Mode With the ATX mode selected the AFL2 12A HM65 panel PC goes in a sta
12. owners Page Ill Se E L K i l Integration Te AFL2 12A HM65 Series Panel PC A WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device and its antenna s must not be co located or operating in conjunction with any o
13. Over tightening back cover screws will crack the plastic frame Maximum torque for cover screws is 5 kg cm 0 36 Ib ft 0 49 Nm To access the AFL2 12A HM65 internally the back cover must be removed To remove the back cover please follow the steps below Step 1 Follow all anti static procedures See Section 5 2 Step 2 Turn off the power See Section 5 3 integration Corp AFL2 12A HM65 Series Panel PC Step 3 Remove a total of nine 9 retention screws from the back cover Figure 5 1 Figure 5 1 Back Cover Retention Screws Step 4 Carefully separate the back cover from the chassis and lift the cover clear of the device 5 4 2 Removing the Internal Aluminum Cover To remove the internal aluminum cover follow the steps below Step 1 Remove the six 6 retention screws securing the internal aluminum cover to the chassis Figure 5 2 AFL2 12A HM65 Series Panel PC Figure 5 2 Internal Cover Retention Screws Step 2 Lift the aluminum cover off the AFL2 12A HM65 5 5 Replacing Components 5 5 1 Memory Module Replacement The flat bezel panel PC is preinstalled with a 1 0 GB DDR3 memory module If the memory module fails follow the instructions below to replace the memory module Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Follow all anti static procedures See Section 5 2 Turn off the power See Section 5 3 Remove the back cover See Section 5 4 1 above Remove
14. Partitions for LINUX d 152 Manual Recovery Environment for LINUX iii 153 Access menu lst in Linux Text Model ssssssssssssssssssssssssssseeese enesenn eee 154 Recovery GENEE 154 Recovery Tool Main Menu 1rr 1rrrrrrreaiii ieri e einen 155 Restore Factory Default inci 156 Recovery Complete WindoW 0irrrereeei iii 157 Backup RE sec ten ceca eee 157 System Backup Complete Window cceceseseeseeeeeeeeeeenesseeeeeseeeenneeeeees 158 MESIOre BACKUD iii 158 Restore System Backup Complete Window ri 159 Symantec Ghost le e EE 159 Page XIII integration Corp AFL2 12A HM65 Series Panel PC List of Tables Table 1 1 AFL2 12A HM65 Model Variations sss sssssssssssssssssssssssssssssseessseeeneee ennenen enne 3 Table EAR pl e Tee egli 6 Table 1 3 afetten Un TE 7 Table 1 4 SVSIemM SPEciICaAlonNSsS cr ina 12 Table 4 1 Ethernet Connector Pinous sssssssss sss esse sees eenn eee 43 Table 4 2 RS 422 485 Serial Port PINOU S rrrrs siii 45 Table 4 3 DB 9 Connector PINOUIS Li ira 46 Table 6 1 BIOS NavigationKeVvS ci cesse essen ennenen eee 60 Page XIV re 0 a r e mem o eee Ul IE l Integrationi corn AFL2 12A HM65 Series Panel PC d a Chapter 1 Introduction AFL2 12A HM65 Series Panel PC 1 1 AFL2 12A HM65 Flat Be
15. Use the Device power up delay BIOS option to configure the device reset timeout gt Auto DEFAULT Device power up delay function is automatic gt Manual Device power up delay function is manual la LI E l Iintegration Corp AFL2 12A HM65 Series Panel PC gt Generic Storage Device 9454 Auto Use the Generic Storage Device 9454 BIOS option to configure the mass storage device gt Auto DEFAULT Sets the mass storage device to automatically detect settings 6 3 5 Super IO Configuration Use the Super IO Configuration menu BIOS Menu 7 to set or change the configurations for the FDD controllers parallel ports and serial ports Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced Super 10 EE EEN Set Parameters of Serial Port 1 COMA Super IO Chip Fintek F81866 gt Serlal Port Configuracion Corral Pore CORE Sellar ebro Conn r a on vol Salece Serson Sci eee E HE TL select Item oerdd POTC EEIT EH EnterSelect i T OE Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 7 Super IO Configuration AFL2 12A HM65 Series Panel PC 6 3 5 1 Serial Port n Configuration Use the Serial Port n Configuration menu BIOS Menu 8 to configure the serial port n Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced Sera Oren Conn E
16. automatically restore from the factory default image after encountering a Blue Screen of Death BSoD or a hang for around 10 minutes Please refer to Section D 3 for the detailed setup procedure The IEI One Key Recovery tool menu is shown below cx X Windows System32 cmd exe i Factory Restore 2 Backup system 3 Restore your last backup 4 Manual 5 Quit Please type the number to select and then press Enterin Figure D 1 IEI One Key Recovery Tool Menu Prior to using the IEI One Key Recovery tool as shown in Figure D 1 to backup or restore Windows system five setup procedures are required A Hardware and BIOS setup see Section D 2 1 Create partitions see Section D 2 2 Install operating system drivers and system applications see Section D 2 3 Build the recovery partition see Section D 2 4 2 3 4 Di Create factory default image see Section D 2 5 Page 131 AFL2 12A HM65 Series Panel PC After completing the five initial setup procedures as described above users can access the recovery tool by pressing lt F3 gt while booting up the system The detailed information of each function is described in Section D 5 Ai NOTE The initial setup procedures for Linux system are described in Section D 3 D 1 1 System Requirement Ai NOTE The recovery CD can only be used with IEI products The software will fail to run and a warning message will appear when used
17. gt Console Redirection Settings select Item Enterselect 1AMT SOL Change Opt Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit EEE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 11 Serial Port Console Redirection gt Console Redirection Disabled Use Console Redirection option to enable or disable the console redirection function gt Disabled DEFAULT Disabled the console redirection function gt Enabled Enabled the console redirection function l anr Ei Integration Corp N D D AFL2 12A HM65 Series Panel PC 6 4 iEi Feature Use the iEi Feature menu BIOS Menu 12 to configure the auto recovery function Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced i1Ei Feature Auto Recovery Function Reboot and recover Auto Recovery Function Disabled system automatically within 10 min when OS crashes Please install Aut OT REcovery API service before enabling PHL REUNEN EE ENEE T J Select Item Enterselect Change Opt General Help Previous Values Optimized Defaults Save amp Exit EE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 12 iEi Feature gt Auto Recovery Function Disabled Use the Auto Recovery Function option to enable or disable auto recovery on the system gt Disabled DEFAULT Auto Recovery Function support disabled gt
18. specifically designed for the purpose In such case the product will be explicitly mentioned in the cleaning tips Below is a list of items to use when cleaning the AFL2 12A HM65 Cloth Although paper towels or tissues can be used a soft clean piece of cloth is recommended when cleaning the AFL2 12A HM65 Water or rubbing alcohol A cloth moistened with water or rubbing alcohol can be used to clean the LAFL2 12A HM65 Using solvents The use of solvents is not recommended when cleaning the LAFL2 12A HM65 as they may damage the plastic parts Vacuum cleaner Using a vacuum specifically designed for computers is one of the best methods of cleaning the AFL2 12A HM65 Dust and dirt can restrict the airflow in the AFL2 12A HM65 and cause its circuitry to corrode Cotton swabs Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas Foam swabs Whenever possible it is best to use lint free swabs such as foam swabs for cleaning Appendix C BIOS Configuration Options Page 127 C 1 Page 128 AFL2 12A HM65 Series Panel PC BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 6 VSEM OVETVICW TTT 61 System Date DOOU Lc 62 VSEM TIMED A d E 62 ACPI Sleep State S3 Suspend to RAM rsa 64 Hyper Threading Function Enabled ccssssssceccssssseeeceessseeeseensseeeseo
19. 0 Driver Welcome Screen triti 113 Figure 7 31 USB 3 0 Driver Choose Install Location rr rire ne eennannna 113 Figure 7 32 USB 3 0 Driver Choose Install Location r rrirrrieiiiiiiiin 114 Figure 7 33 USB 3 0 Driver Installation Complete ccseeeeeesscesssneeeeseeeeensneeeeeeseeees 114 Figure D 1 IEI One Key Recovery Tool Menu s seeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeanaes 131 Figure D 2 Launching the Recovery TOO cccccceeeeeeeeeeeneseeeeeeeeneeeeeeeaaseeeseeeeaaeeeseeeeeseesens 136 Figure D 3 Recovery Tool Setup MENU 136 Figure D 4 Command Prompt E 137 Figure D 5 Partition Creation CommandS 1111 2rrrrrrrrreei iii 138 Figure D 6 Launching the Recovery Tool rrrrrreniriiiiriiiiiiiiiiiiin 140 Figure D 7 Manual Recovery Environment for WindowSs 2rr creeranno 140 Figure D 8 Building the Recovery Partition rr 141 Figure D 9 Press Any Key to Continue ssxssssssssssssssszzzzaazaniz eenn 141 Figure D 10 Figure D 11 Figure D 12 Figure D 13 Figure D 14 Figure D 15 Figure D 16 Figure D 17 Figure D 18 Figure D 19 Figure D 20 Figure D 21 Figure D 22 Figure D 23 Page XII Press F3 to Boot into Recovery Mode
20. 2 10 1208 Copyright BIOS Menu 3 ACPI Configuration S3 Suspend to RAM 2010 American Megatrends Inc Select the highest ACPI sleep state the system will enter when the SUSPEND ceo 15 pressed So TY Select Item EnterSelect o Change Ope Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit E CEI 2010 American Megatrends Inc integration Corp AFL2 12A HM65 Series Panel PC gt ACPI Sleep State S3 Suspend to RAM Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used gt Suspend Disabled Suspend function disabled gt si CPU Stop The system enters S1 POS sleep state The Clock system appears off The CPU is stopped RAM is refreshed the system is running in a low power mode gt 3 Suspend to DEFAULT The caches are flushed and the CPU is powered RAM off Power to the RAM is maintained The computer returns slower to a working state but more power is saved 6 3 2 CPU Configuration Use the CPU Configuration menu BIOS Menu 4 to view detailed CPU specifications and configure the CPU AFL2 12A HM65 Series Panel PC A D D Corp a B i SH f l Iintegratio n Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced CRUECO TETE ince RF Cone IMn 2S TOER PU RS DEER Processor Stepping Microcode Revision Max Processor Speed
21. 4 Install the auto recovery utility into the system by double clicking the Utility AUTORECOVERY SETUP exe in the One Key Recovery CD This utility MUST be installed in the system otherwise the system will automatically restore from the factory default image every ten 10 minutes Step 5 Restart the client system from LAN If the system encounters a Blue Screen of Death BSoD or a hang for around 10 minutes it will automatically restore from the factory default image The following screens will show when the system starts auto recovering Realtek PCIe GBE Family Controller Series v2 35 06 14 10 CLIENT MAC ADDR 66 18 7D 13 Eb 89 GUID B0929083 B984 AB05 B986 BBA7000801 DHCP lt Page 166 niCorp AFL2 12A HM65 Series Panel PC My IP address seems to be COABBBBS 192 168 0 9 ip 192 168 0 9 192 168 0 8 192 168 2 255 255 255 8 TFTP prefix Trying to pxelinux cfg 00929093 9904 9995 9906 000700880089 Trying to pxelinux cfg 01 00 18 7d 13 e6 89 Trying to pxelinux cfg C9A89009 Trying to pxelinux cfg C9A8800 Trying to pxelinux cfg C9A880 Trying to pxelinux cfg C9A88 Trying to pxelinux cfg CBA8 Trying to pxelinux cfg C A Trying to pxelinux cfg C Trying to pxelinux cfg C Trying to pxelinux cfg default boot Windows is loading files IP 192 168 0 8 File Boot WinPE wim Symantec Ghost 11 5 Copyright C 1998 2008 Symantec Corporation All rights reserved Typ
22. 45 connector Once aligned gently insert the LAN cable RJ 45 connector into the onboard RJ 45 connector 4 9 2 Serial Device Connection The AFL2 12A HM65 has one male DB 9 port connector and one RuJ 45 serial port connector on the I O panel for serial device connection integration Corp AFL2 12A HM65 Series Panel PC 4 9 2 1 DB 9 Serial Port Connection Follow the steps below to connect a serial device to the DB 9 connector of the AFL2 12A HM65 panel PC Step 1 Locate the DB 9 connector The location of the DB 9 connector is shown in Chapter 2 Step 2 Insert the serial connector Insert the DB 9 connector of a serial device into the DB 9 connector on the bottom panel See Figure 4 16 Figure 4 16 DB 9 Serial Port Connector Step 3 Secure the connector Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector 4 9 2 2 RJ 45 Serial Port Connection CN Label COM3 CN Type RJ 45 CN Location See Figure 4 17 Page 42 AFL2 12A HM65 Series Panel PC CN Pinouts See Table 4 1 The RJ 45 serial port connector connects to RS 232 serial devices 1 8 Figure 4 17 Ethernet Connector Follow the steps below to connect a serial device to the RJ 45 serial port connector of the AFL2 12A HM65 panel PC Step 1 Locate the RJ 45 serial port The location of the RJ 45 serial port is shown in Chapter 2 Step 2 Connec
23. 60 Hz Output 19V DC Power Requirement 9V 36V DC Power Consumption 51W LED Functions Power RFID MIC Auto dimming Wi Fi RFID device AT ATX mode Camera Bluetooth USB port CPU temperature alert 1 0 Ports and Switches 1 x RS 232 DB 9 connector 1 x RS 232 RJ 45 connector 1 x RS 422 485 4 pin box header 1 x GbE LAN RJ 45 connector 2 X USB 2 0 connector 2 x USB 3 0 connector 1 x Mini USB 2 0 connector on front panel 1 x Audio jack line out 1 x HDMI port 1 x SD card slot on front panel 1 x Reset button 1 x Power switch 1 x AT ATX switch 1 x DC input jack 1 x Clear CMOS button Table 1 4 System Specifications a A a P e T Ka Ss SS WO Chapter 2 Detailed Specifications Page 13 s de R n AFL2 12A HM65 Series Panel PC 2 1 Dimensions The AFL2 12A HM65 dimensions are shown below Width 310 0 mm Height 265 0 mm Depth 52 6 mm Figure 2 1 AFL2 12A HM65 Dimensions mm Page 14 E E E l Iintegrationi Corp AFL2 12A HM65 Series Panel PC Figure 2 2 AFL2 12A HM65 Dimensions mm cont Page 15 Integration Corp AFL2 12A HM65 Series Panel PC 2 2 Intel Sandy Bridge Mobile Processor An Intel Sandy Bridge Mobile processor is installed in the system The Sandy Bridge CPU interfaces with the HM65 chipset through a Direct Media Interface DMI with speed of 5 GT s and a Flexible Display
24. 7 Moonshine O RedHat RHEL 5 4 O RedHat 9 Ghirke Page 133 integration Corp AFL2 12A HM65 Series Panel PC Ubuntu 8 10 Intrepid Ubuntu 7 10 Gutsy Ubuntu 6 10 Edgy Debian 5 0 Lenny Debian 4 0 Etch SuSe 11 2 SuSe 10 3 O O O 0O St O O Ai NOTE Installing unsupported OS versions may cause the recovery tool to fail D 2 Setup Procedure for Windows Prior to using the recovery tool to backup or restore a few setup procedures are required Step 1 Hardware and BIOS setup see Section D 2 1 Step 2 Create partitions see Section D 2 2 Step 3 Install operating system drivers and system applications see Section D 2 3 Step 4 Build the recovery partition see Section D 2 4 or build the auto recovery partition see Section D 3 Step 5 Create factory default image see Section D 2 5 The detailed descriptions are described in the following sections Ai NOTE The setup procedures described below are for Microsoft Windows operating system users For Linux most of the setup procedures are the same except for several steps described in Section D 3 Page 134 r e EN integration AFL2 12A HM65 Series Panel PC D 2 1 Hardware and BIOS Setup Step 1 Make sure the system is powered off and unplugged Step 2 Install a hard drive or SSD in the system An unformatted and unpartitioned disk is recommended Step 3 Connect an optical disk drive to the system and inser
25. AFL2 12A HM65 Series Panel PC PenMount Universal Driver V2 1 0 263 Setup Choose Install Location Choose the Folder in which to install PenMount Universal Driver W2 1 0 263 Setup will install PenMount Universal Driver V2 1 0 263 in the following folder To install in a different Folder click Browse and select another Folder Click Install to start the installation Destination Folder CProgram FilestPenMount Universal Driver Space required D 0KB Space available 36 006 Mullsort Install System v2 45 Figure 7 19 Touch Screen Driver Choose Install Location Step 10 The Install screen appears and displays the progress of the installation Figure 7 20 Page 106 AFL2 12A HM65 Series Panel PC Step 11 Click NEXT to continue PenMount Universal Driver V2 1 0 763 Setup Installing Please wait while PenMount Universal Driver 2 1 0 263 is being installed Execute C Program FilesiPenMount Universal Driverlinstalli exe Install Show details l Nullsoft Install System v2 45 Figure 7 20 Touch Screen Driver Installation Screen Step 12 When the installation is complete click FINISH to exit setup Figure 7 21 PenMount Universal Driver V2 1 0 263 Setup Completing the PenMount Universal Driver 2 1 0 263 Setup Wizard PenMount Universal Driver 2 1 0 263 has been installed on your computer Click Finish to close this wizard Figure 7 21 Touch Screen Driver Update Compl
26. Enabled Auto Recovery Function support enabled AFL2 12A HM65 Series Panel PC 6 5 Chipset Use the Chipset menu BIOS Menu 13 to access the Northbridge and Southbridge configuration menus A WARNING Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main notoc Chipset Security Save amp Exit a Norther ridge Conr EE NorthBridge Parameters Rubra BEE Con lasci TY Select Item EnterSelect Oa O El General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit oo EXIL Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 13 Chipset la LI 15 l Iintegrationi Corp AFL2 12A HM65 Series Panel PC 6 5 1 NorthBridge Configuration Use the NorthBridge Configuration menu BIOS Menu 14 to configure the northbridge chipset Aptio Setup Utility Copyright C 2010 American Megatrends Inc Chipset NorthBridge Configuration Conigli Settings Memory Information Memory Frequency oe Haz Total Memory 1024 MB DDR3 DIMM 1 1024 MB DDR3 Cra phies E TEE kr Hon D ini I n Enterselect 7 Change Ope Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESCE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 14 Host Bridge Chipse
27. Ensure that all four of the mounting screws fit snuggly into their respective slotted holes Ai NOTE In the diagram below the bracket is already installed on the wall integration Corp AFL2 12A HM65 Series Panel PC Figure 4 8 Chassis Support Screws Step 9 Secure the panel PC by fastening the retention screw of the wall mounting bracket Figure 4 9 Figure 4 9 Secure the Panel PC AFL2 12A HM65 Series Panel PC 4 8 2 Stand Mounting To mount the AFL2 12A HM65 using the stand mounting kit please follow the steps below Step 1 Locate the screw holes on the rear of the AFL2 12A HM65 This is where the bracket will be attached Figure 4 10 100 mm 100 mm Figure 4 10 Mounting screw location Step 2 Align the bracket with the screw holes Step 3 To secure the bracket to the AFL2 12A HM65 insert the retention screws into the screw holes and tighten them 4 8 3 Arm Mounting The AFL2 12A HM65 is VESA Video Electronics Standards Association compliant and can be mounted on an arm with a 100mm interface pad To mount the AFL2 12A HM65 on an arm please follow the steps below Step 1 The arm is a separately purchased item Please correctly mount the arm onto the surface it uses as a base To do this refer to the installation documentation that came with the mounting arm Integration Corp AFL2 12A HM65 Series Panel PC Ai NOTE When purchasing
28. Figure 7 30 USB 3 0 Driver Welcome Screen Step 6 Browse for an install location or use the one suggested Figure 7 31 Step 7 Click NEXT to continue fig Logic USB3 0 Host Controller Setup Select Installation Folder This is the folder where Fresco Logic USB3 0 Host Controller will be installed To install in this Folder click Next To install to a different folder enter it below or click Browse Folder c Program Files Fresco Logic Fresco Logic USB3 0 Host Controller Fresco Logic Inc Figure 7 31 USB 3 0 Driver Choose Install Location Step 8 The program is ready to install Figure 7 32 Step 9 Click INSTALL to continue Page 113 integration Corp AFL2 12A HM65 Series Panel PC ix Fresco Logic USB3 0 Host Controller Setup Ready to Install The Setup Wizard is ready to begin the Fresco Logic USB3 0 Host Controller install Click Install to begin the installation IF you want to review or change any of your installation settings click Back Click Cancel to exit the wizard Fresco Logic Inc Figure 7 32 USB 3 0 Driver Choose Install Location Step 10 When the driver installation is complete the screen in Figure 7 33 appears Step 11 Click Finish to exit Cl Fresco Logic USB3 0 Host Controller Setup Completing the Fresco Logic USB3 0 Host Controller Setup Wizard Click the Finish button to exit the Setup Wizard lt Back Cancel Figure 7 33 USB 3 0 Driver Ins
29. I O interface connector panel is shown in Figure 1 6 Power Switch 2x USB 3 0 Ports 2 x USB 2 0 Ports RS 422 485 GbE K LE G ke D a D gt te C l gt Ler RS 232 HDMI Function Keys ATIATX Switch Clear CMOS Switch Figure 1 6 AFL2 12A HM65 UO Interface Panel 1 2 4 Top Panel and Side Panels The top panel and side panels of AFL2 12A HM65 provide access to slots that support the rack mount Figure 1 7 Top Slots for Panel or Rack Mount Clips Figure 1 7 Top Panel View integration Corp AFL2 12A HM65 Series Panel PC Side Slots for Panel or Rack Mount Clips Figure 1 8 Side Panel Views 1 3 Internal Overview The AFL2 12A HM65 has the following components installed internally 1x Motherboard 1 x 1 0 GB 800 MHz DDR3 SO DIMM WW i Fd E l Iintegratio AFL2 12A HM65 Series Panel PC 1 4 System Specifications The technical specifications for the AFL2 12A HM65 systems are listed in Table 1 4 Touch Screen 5 Wire resistive type touchscreen select models only Projected capacitive type touchscreen select models only SATA SSD One PCle mini slot with SATA signal and IEI MiniDOM support AMP 1 5 W 1 5 W built in stereo speakers integration Corp AFL2 12A HM65 Series Panel PC Arm VESA 100 mm x 100 mm IP 64 compliant front panel Power Adapter 90W Input 100V AC 240V AC 50
30. Interface FDI 2 3 Motherboard Components The following sections describe some of the features on the motherboard 2 3 1 Memory Support 2 3 1 1 Installed Memory One 204 pin 1 0 GB 800 MHz DDR3 SO DIMM is installed in the AFL2 12A HM65 and controlled by the Intel Sandy Bridge Mobile CPU installed on the internal motherboard 2 3 2 Storage Capacity The AFL2 12A HM65 comes equipped with a 2 5 SATA 3 0 HDD drive bay which can be easily accessed by removing two screws on the HDD cover 2 4 External Peripheral Interface Connectors The following section describes the external peripheral interface connectors on the bottom panel of the subsystem 2 4 1 Serial Port Connectors The AFL2 12A HM65 has three serial ports COM1 and COM8 support only RS 232 serial communications The other serial port COME can be configured as an RS 422 or RS 485 serial port Enabling COM devices to be powered through the COM port eliminates unnecessary and messy cabling ago lt e E l Iintegratio AFL2 12A HM65 Series Panel PC RS 422 485 COM6 RS 232 COM3 Figure 2 3 COM Ports 2 4 2 LAN Connectivity The AFL2 12A HM65 has one RJ 45 LAN connector on the bottom panel GbE RJ 45 Connector Figure 2 4 RJ 45 Ethernet Connectors The PCle LAN from the Intel HM65 chipset of the AFL2 12A HM65 is interfaced to the Realtek RTL8111E PCle gigabit Ethernet GbE controllers The RTL8111E controller is connected directly to t
31. PC ST SATA_AXPO_C e SATA_RXNO_C Table A 21 Touch Panel Connector TS1 Pinouts Page 120 AFL2 12A HM65 Series Panel PC 1 Texcrower 2 ext power SR ENAGKI GS caos E Jesse eos on e osa ome _ P_ eos on e osa ome _ D fro vos ar _ vee Leb CC vee Leb Table A 24 LVDS Connector LVDS1 Pinouts DESCRIPTION Table A 25 Touch Panel Connector TOUCH1 Pinouts Page 121 Appendix B Safety Precautions Page 122 WW ame Su E l Integrationi AFL2 12A HM65 Series Panel PC A WARNING The precautions outlined in this chapter should be strictly followed Failure to follow these precautions may result in permanent damage to the AFL2 12A HM65 B 1 Safety Precautions Please follow the safety precautions outlined in the sections that follow B 1 1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times Follow the electrostatic precautions outlined below whenever the AFL2 12A HM65 is opened Make sure the power is turned off and the power cord is disconnected whenever the AFL2 12A HM65 is being installed moved or modified Do not apply voltage levels that exceed the specified voltage range Doing so may cause fire and or an electrical shock Electric shocks can occur if the AFL2 12A HM65 chassis is opened when the AFL2 12A HM65 is running Do not drop or insert any objects into the ventilation open
32. Status CPU Temperature 64 C SYS Temperature A e CPU FAN Speed 4643 RPM VOCON EE ten E E Oa 26 Vos eo V12S 11 968 V Sole do lA 1 TY Select Item Ee 200 EnterSelect VBAT rogo oi Change Opt 5VSB uo IZ Fl General Help F2 Previous Values AE ong EE F3 Optimized Defaults F4 Save amp Exit To Spike Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 9 Hardware Health Configuration gt PC Health Status The following system parameters and values are shown The system parameters that are monitored are System Temperatures O CPU Temperature O System Temperature Fan Speeds O CPU Fan Speed e 2 de l Iintegrationi Corp AFL2 12A HM65 Series Panel PC Voltages VCC3V Vcc_core V5S V12S 1 5V VSB3V VBAT 5VSB O O O e 0 O 0 6 3 6 1 Fan 1 Configuration The Fan 1 Configuration submenu BIOS Menu 9 allows user to configure the CPU Smart fan settings Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced PC Health Status E Smart Fan corto Auto Mode Temperature Of Start 80 Temperature Of Off Ta Seat EWM 20 Slope PWM duty 4 PWM duty 3 Select Screen tT J Select Item Enterselect Change Opt Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit SC due Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 10 Hardware Health Configuration
33. The Rack Cabinet Bracket Step 2 Insert the rack mounting clamps into the pre formed holes along the edges of the flat bezel panel PC behind the ABS PC plastic frame There are a total of 6 rack mounting clamps Step 3 Tighten the screws that pass through the rack mounting clamps until the plastic caps at the front of all the screws are firmly secured to the bracket Figure 4 13 AFL2 12A HM65 Series Panel PC Figure 4 13 Secure the Rack Cabinet Bracket Step 4 Slide the flat bezel panel PC with the attached rack cabinet bracket into a rack or cabinet Figure 4 14 Figure 4 14 Install into a Rack Cabinet Step 5 Once the flat bezel panel PC with the attached rack cabinet bracket has been properly inserted into the rack or cabinet secure the front of the rack cabinet bracket to the front of the rack or cabinet Figure 4 14 AFL2 12A HM65 Series Panel PC 4 9 Bottom Panel Connectors 4 9 1 LAN Connection There is one external RJ 45 LAN connector The RJ 45 connector enables connection to an external network To connect a LAN cable with an RJ 45 connector please follow the instructions below Step 1 Locate the RJ 45 connector on the bottom panel of the AFL2 12A HM65 Step 2 Align the connector Align the RJ 45 connector on the LAN cable with the RJ 45 connectors on the bottom panel of the AFL2 12A HM65 See Figure 4 15 Figure 4 15 LAN Connection Step 3 Insert the LAN cable RJ
34. ana bal bead i R E Figure D 12 About Symantec Ghost Window Step 4 Use mouse to navigate to the option shown below Figure D 13 ES peee ber o Image Figure D 13 Symantec Ghost Path Step 5 Select the local source drive Drive 1 as shown in Figure D 14 Then click OK Page 143 E ES 2 I E integration Corp LLN AFL2 12A HM65 Series Panel PC Select local source drive by clicking on the drive number Figure D 14 Select a Local Source Drive Step 6 Select a source partition Part 1 from basic drive as shown in Figure D 15 Then click OK Select source partition s from Basic drive 1 Figure D 15 Select a Source Partition from Basic Drive Step 7 Select 1 2 Recovery NTFS drive and enter a file name called iei Figure D 16 Click Save The factory default image will then be saved in the selected recovery drive and named IEI GHO A WARNING The file name of the factory default image must be iei GHO Page 144 AFL2 12A HM65 Series Panel PC File name to copy image to E3 D L t Recovery NTFS drive Recovery fm SOURCES FS System Volume Information Figure D 16 File Name to Copy Image to Step 8 When the Compress Image screen in Figure D 17 prompts click High to make the image file smaller Compress Image Figure D 17 Compress Image Page 145 l Leg d e Lal G i 4 f 48 pe DS B lt i
35. board SATA controller to be in compatible mode In this mode a SATA channel will replace one of the IDE channels This mode supports up to 6 storage devices gt Enhanced DEFAULT Configures the on board SATA controller to be in Enhanced mode In this mode IDE channels and SATA channels are separated SATA Mode Selection IDE Use the SATA Mode Selection option to configure SATA devices as normal IDE devices gt IDE DEFAULT Configures SATA devices as normal IDE device gt AHCI Configures SATA devices as AHCI device AFL2 12A HM65 Series Panel PC 6 3 4 USB Configuration Use the USB Configuration menu BIOS Menu 6 to read USB configuration information and configure the USB settings Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced USB Contigurarion Ves BETEG Perae Ters US Dewees 1 Drive 2 Keyboards 2 Hubs Enabled SL Saleen Enabled Do elica Baeto Leci kacor oleet Enabled SEENEN Dab ee ollie Fl General Help Enabled F2 Previous Values F3 Optimized Defaults USB hardware delays and time outs F4 Save amp Exit USB transfer time our 20 sec ESC Exit Device reset time out 20 sec Device power up delay Auto Usb OUP POrE Legacy USB Suppor USB o 207 support HC t Hamden EEC ie HRES Orr Port 60 64 Emulation Mass Storage Devices Generic STORAGE DEVICE 9454 Auto Version 2 10 1208 Copyright C 2010 American Megatrends
36. gt 416M DVMT memory size set at 416 MB gt 448M DVMT memory size set at 448 MB gt 480M DVMT memory size set at 480 MB gt 512M DVMT memory size set at 512 MB gt DVMT Total Gfx Mem MAX Use the DVMT Total Gfx Mem BIOS option to configure the DVMT total graphics memory size gt 128M Sets the DVMT Total Gfx Mem size to 128 MB gt 256M Sets the DVMT Total Gfx Mem size to 256 MB gt MAX DEFAULT Sets the DVMT Total Gfx Mem size to maximum gt Boot Display Device LFP Use the Boot Display Device BIOS option to configure the boot display device gt HDMI Sets the boot display device to HDMI gt LFP DEFAULT Sets the boot display device to LFP gt LCD Panel Type 1024x768 18BIT Use the LCD Panel Type BIOS option to configure the LCD panel type AFL2 12A HM65 Series Panel PC gt 800x600 Sets the panel resolution at 800x600 18 bit 18BIT gt 1024x768 DEFAULT Sets the panel resolution at 1024x768 18 bit 18BIT gt 1024x768 Sets the panel resolution at 1024x7678 24 bit 24BIT 6 5 2 South Bridge Configuration Use the South Bridge Configuration menu BIOS Menu 16 to configure the southbridge chipset Aptio Setup Utility Copyright C 2010 American Megatrends Inc Chipset SouthBridge Configuration Enabled or Disabled USB Controller AUCO Power Burton E SE ES ON USE Compra lei Enabled USB 320 Controller Enabled Sile Azalia Enabled TL Select Item Afzelia Intermal HDMi Codee En
37. gt Disabled XHCI Hand off disabled gt EHCI Hand off Disabled Use the EHCI Hand off BIOS option to enable EHCI Hand off support This is a workaround for OSes without EHCI hand off support The EHCI ownership change should be claimed by the EHCI driver gt Enabled EHCI Hand off enabled gt Disabled DEFAULT EHCI Hand off disabled Integration Corp AFL2 12A HM65 Series Panel PC gt Port 60 64 Emulation Enabled Use the Port 60 64 Emulation BIOS option to enable Port 60 64 Emulation support This should be enabled for complete USB keyboard legacy support for non USB aware OSes gt Enabled DEFAULT Port 60 64 Emulation enabled gt Disabled Port 60 64 Emulation disabled gt USB transfer time out 20 sec Use the USB transfer time out BIOS option to configure the USB transfer timeout gt 1sec Sets the USB transfer time out to 1 second gt 5sec Sets the USB transfer time out to 5 seconds gt 10sec Sets the USB transfer time out to 10 seconds gt 20sec DEFAULT Sets the USB transfer time out to 20 seconds gt Device reset time out 20 sec Use the Device reset time out BIOS option to configure the device reset timeout gt 10sec Sets the Device reset time out to 10 seconds gt 20sec DEFAULT Sets the Device reset time out to 20 seconds gt 30sec Sets the Device reset time out to 30 seconds gt 40sec Sets the Device reset time out to 40 seconds gt Device power up delay Auto
38. gt RCT CHE TEATS THE ARLE EFEK BEA SOUS TUNES Gir Gi ATE so o o o VI o PBDE mm van T CO sem DD le l____ Da 20 D 77 BE 2 O ri En SEEM A AT A SEL SI T11363 2006 AEM TEOR TL F A RRA BA SED ERE EE SRL GT 11363 2006 EMEREK Page 177
39. of Watchdog Timer first If the time out value is not zero the Watchdog Timer starts counting down While the timer value reaches zero the system resets To ensure that this reset condition does not occur calling sub function 2 must periodically refresh the Watchdog Timer However the Watchdog timer is disabled if the time out value is set to zero A tolerance of at least 10 must be maintained to avoid unknown routines within the operating system DOS such as disk I O that can be very time consuming Page 172 die iE 1 Integration Corp AFL2 12A HM65 Series Panel PC Ai NOTE When exiting a program it is necessary to disable the Watchdog Timer otherwise the system resets Example program INITIAL TIMER PERIOD COUNTER LU l W_LOOP MOV AX 6FO2H setting the time out value MOV BX 05 time out value is 5 seconds INT 15H ADD THE APPLICATION PROGRAM HERE LU l CMP EXIT_AP 1 is the application over JNE W_LOOP No restart the application MOV AX 6F02H disable Watchdog Timer MOV BX 0 INT 15H LU H EXIT Page 173 Appendix gt Hazardous Materials Disclosure Page 174 AFL2 12A HM65 Series Panel PC F 1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002 95 EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China China Ro
40. on non lEl hardware XR NI3B6Xsustem32 gt call start exe Projecti x This software only runs on IEI hardware RSC To create the system backup the main storage device must be split into two partitions three partitions for Linux The first partition will be for the operating system while the second partition will be invisible to the operating system and contain the backup made by the one key recovery software The partition created for recovery images must be big enough to contain both the factory default image and the user backup image The size must be calculated before creating the Page 132 Te EN integration AFL2 12A HM65 Series Panel PC partitions Please take the following table as a reference when calculating the size of the partition Windows XPE 776 MB 560 Me Windows CE 6 0 36 MB 28 MB 77 Ai NOTE Specialized tools are required to change the partition size if the operating system is already installed D 1 2 Supported Operating System The recovery CD is compatible with both Microsoft Windows and Linux operating systems OS The supported OS versions are listed below Microsoft Windows Windows XP Service Pack 2 or 3 required Windows Vista Windows 7 Windows CE 5 0 Windows CE 6 0 Windows XP Embedded Linux Fedora Core 12 Constantine O Fedora Core 11 Leonidas Fedora Core 10 Cambridge O Fedora Core 8 Werewolf O Fedora Core
41. properly installed When maintenance procedures are complete please make sure all the covers are replaced including the following Aluminum internal cover Plastic back cover Plastic HDD cover Chapter 6 AMI BIOS Setup Page 58 WW apre oe E l Iintegrationi AFL2 12A HM65 Series Panel PC 6 1 Introduction A licensed copy of the BIOS is preprogrammed into the ROM BIOS The BIOS setup program allows users to modify the basic system configuration This chapter describes how to access the BIOS setup program and the configuration options that may be changed 6 1 1 Starting Setup The UEFI BIOS is activated when the computer is turned on The setup program can be activated in one of two ways 1 Press the F2 or DEL key as soon as the system is turned on or 2 Press the F2 or DEL key when the Press F2 to enter SETUP message appears on the screen If the message disappears before the F2 or DEL key is pressed restart the computer and try again 6 1 2 Using Setup Use the arrow keys to highlight items press ENTER to select use the PageUp and PageDown keys to change entries press F1 for help and press Esc to quit Navigation keys are shown in the following table e ege BEE EES Page Up key Move to the next page Page Dn key Move to the previous page AFL2 12A HM65 Series Panel PC Esc key Main Menu Quit and do not save changes into CMOS Status Page
42. with the procedure for Microsoft Windows Please follow the steps below to setup recovery tool for Linux OS Step 1 Hardware and BIOS setup Refer to Section D 2 1 Page 151 AFL2 12A HM65 Series Panel PC Step 2 Install Linux operating system Make sure to install GRUB v0 97 or earlier MBR type and Ext3 partition type Leave enough space on the hard drive to create the recover partition later Ai NOTE If the Linux OS is not installed with GRUB v0 97 or earlier and Ext3 the Symantec Ghost may not function properly While installing Linux OS please create two partitions Partition 1 Partition 2 SWAP Ai NOTE Please reserve enough space for partition 3 for saving recovery images Partition sindaz Type SWAF Figure D 29 Partitions for Linux Step 3 Create a recovery partition Insert the recovery CD into the optical disk drive Follow Step 1 Step 3 described in Section D 2 2 Then type the following commands marked in red to create a partition for recovery images system32 gt diskpart DISKPART gt list vol DISKPART gt sel disk 0 Page 152 AFL2 12A HM65 Series Panel PC Step 4 ia la agmo lt E la E l Iintegratio rp lt TN DISKPART gt create part pri size __ DISKPART gt assign letter N DISKPART gt exit system32 gt format N fs ntfs q v Recovery y system32 gt exit Build the recovery partition Press an
43. 1 5 Wire Resistive N A Table 1 1 AFL2 12A HM65 Model Variations 1 1 2 Features The AFL2 12A HM65 features are listed below 12 1 600 cd m XGA LCD Intel Sandy Bridge Mobile CPU supported Intel HM65 chipset 1 0 GB 800 MHz DDR3 SO DIMM preinstalled 4 GB maximum RFID module compatible with EM or MIFARE cards Watchdog timer that triggers a system reset if the system hangs for some reason IP 64 compliant front panel AT or ATX power mode 5 Wire Resistive or Projected Capacitive type touch screen ROHS compliance Auto dimming control 1 3 megapixel webcam 1 1 3 Applications AFL2 12A HM65 Series panel PCs are elegant sophisticated systems that can be easily implemented in commercial industrial and corporate environments Integration Corp AFL2 12A HM65 Series Panel PC 1 2 External Overview 1 2 1 Front Panel The front side of the AFL2 12A HM65 is a flat bezel panel TFT LCD screen surrounded by an ABS PC plastic frame Webcam TouchScreen ABS Plastic Frame LED Indicators LED Indicators RFID Sensor Figure 1 2 AFL2 12A HM65 Front View e i E l Integration Corp AFL2 12A HM65 Series Panel PC 1 2 1 1 LED Indicators There are fifteen LED indicator lights located along the front of the LCD screen Figure 1 3 oo gt gt a C Q o c w E oa cao E SS Z ZE gs E 6 2 5 o 4 SS SE e S ea S
44. 6 Press any key to exit the recovery tool and automatically reboot the system Please continue to the following procedure Build the Recovery Partition D 2 3 Install Operating System Drivers and Applications Install the operating system onto the unlabelled partition The partition labeled Recovery is for use by the system recovery tool and should not be used for installing the operating system or any applications Ai NOTE The operating system installation program may offer to reformat the chosen partition DO NOT format the partition again The partition has already been formatted and is ready for installing the new operating system To install the operating system insert the operating system installation CD into the optical drive Restart the computer and follow the installation instructions Page 139 AFL2 12A HM65 Series Panel PC D 2 4 Building the Recovery Partition Step 1 Putthe recover CD in the optical drive Step 2 Start the system Step 3 Boot the system from the recovery CD When prompted press any key to boot from the recovery CD It will take a while to launch the recovery tool Please be patient Starting Hindous Proinstallation Environment HM Figure D 6 Launching the Recovery Tool Step 4 When the recovery tool setup menu appears press lt 2 gt then lt Enter gt i Execute Ghost Z Manual Recovery environment For Windows i3 Manual Recovery environment
45. Driver Setup Operations Step 16 The Finish screen in Figure 7 13 appears Step 17 Select Yes want to restart this computer now and click Finish Page 101 integration Corp AFL2 12A HM65 Series Panel PC Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator Driver Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the computer now a Yes I want to restart this computer now No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Figure 7 13 Graphics Driver Installation Finish Screen 7 5 Audio Driver Installation To install the audio driver please do the following Step 1 Step 2 Step 3 Step 4 Step 5 Page 102 Access the driver list See Section 7 2 Click Audio and select the folder which corresponds to your operating system Double click the setup file The Audio Driver Welcome Screen in Figure 7 14 appears Click Next to continue AFL2 12A HM65 Series Panel PC Realtek High Definition Audio Driver Setup 2 89 R2 40 Welcome to the InstallShield Wizard for Realtek High Definition Audio Driver The InstallShield Wizard will install Realtek High Definition Audio Driver on your computer To continue click Next InstallShield Figure 7 14 Audio Driver Welcome Screen Step 6 The
46. E EE Enable or Disable Serial Port COM Serial Pore Enabled Device Settings IO 3F8h IRQ 4 Change Settings Auto Select Screen TJ Select Item Enterselect wchange Ope Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit o che Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 8 Serial Port n Configuration Menu 6 3 5 1 1 Serial Port 1 Configuration gt Serial Port Enabled Use the Serial Port option to enable or disable the serial port gt Disabled Disable the serial port gt Enabled DEFAULT Enable the serial port gt Change Settings Auto Use the Change Settings option to change the serial port IO port address and interrupt address gt Auto DEFAULT The serial port IO port address and interrupt address are automatically detected gt lO 3F8h Serial Port I O port address is 3F8h and the interrupt IRQ 4 address is IRQ4 io e a L En integration Corp c go lt Q AFL2 12A HM65 Series Panel PC gt IO 3F8h Serial Port I O port address is 3F8h and the interrupt IRQ 3 4 address is IRQ3 4 gt lO 2F8h Serial Port I O port address is 2F8h and the interrupt IRQ 3 4 address is IRQ3 4 6 3 6 H W Monitor The H W Monitor menu BIOS Menu 9 shows the operating temperature fan speeds and system voltages Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced PC Health
47. E H egrat H d pei pe ee musce ai d i ue VA AFL2 12A HM65 Series Panel PC Step 9 The Proceed with partition image creation window appears click Yes to continue Question 18373 Figure D 18 Image Creation Confirmation Step 10 The Symantec Ghost starts to create the factory default image Figure D 19 rved Type NTFS 100006 HB 1951 HB used No name from Local drive 80 130129 HB Local file D iei GHO t Figure D 19 Image Creation Complete Step 11 When the image creation completes a screen prompts as shown in Figure D 20 Click Continue and close the Ghost window to exit the program Image Creation Complete 1925 Continue Figure D 20 Image Creation Complete Page 146 d P s D bw D lt Carn a npo c 3 E l Integrati Q AFL2 12A HM65 Series Panel PC Step 12 The recovery tool main menu window is shown as below Press any key to reboot the system n X Windows System32 cmiLexe Factory Restore Backup system Restore your last backup Manual Quit Please type the number to select and then press Enter 4 Done Press any key to continue Figure D 21 Press Any Key to Continue D 3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death BSoD or a h
48. For Linux 4 fiuto Recovery environment For Windows b Exit 6 Command Prompt Type the number to print text 2 Figure D 7 Manual Recovery Environment for Windows Page 140 vel l Integration Re a Corp S AFL2 12A HM65 Series Panel PC Step 5 The Symantec Ghost window appears and starts configuring the system to build a recovery partition In this process the partition created for recovery files in Section D 2 2 is hidden and the recovery tool is saved in this partition E Ghost32 11 5 61 fi Company Backup Tool 1 0 1 Copyright Ca ii G Somantec Corp 000 Type NTFS 26936 HB 227 HB used Recovery from Local file fiscovery_PE2 gho 476938 HB Type NTFS 20002 HB from Local drive CLI 152627 HB Paslor remaining NTFS HFT es Figure D 8 Building the Recovery Partition Step 6 After completing the system configuration press any key in the following window to reboot the system Go C V AINDO WS eystem32 cmd exe H Execute Ghost Manual Recovery environment For Windows 3 Manual Recovery environment For Linux 4 Auto Recovery environment For Windows E Exit 6 Command Prompt Type the number to print text 2 Press any key to continue gt Figure D 9 Press Any Key to Continue Step 7 Eject the recovery CD Page 141 AFL2 12A HM65 Series Panel PC D 2 5 Create Factory Default Image Ai NOTE Before creating the fa
49. HM65 Dry climates are especially susceptible to ESD It is therefore critical that whenever the AFL2 12A HM65 is accessed internally or any other electrical component is handled the following anti static precautions are strictly adhered to Wear an anti static wristband Wearing a simple anti static wristband can help to prevent ESD from damaging the board Self grounding Before handling the board touch any grounded conducting material During the time the board is handled frequently touch any conducting materials that are connected to the ground Use an anti static pad When configuring the AFL2 12A HM65 place it on an antic static pad This reduces the possibility of ESD damaging the AFL2 12A HM65 Only handle the edges of the PCB When handling the PCB hold the PCB by the edges LEE integration AFL2 12A HM65 Series Panel PC 5 3 Turn off the Power A WARNING Failing to turn off the system before opening it can cause permanent damage to the system and serious or fatal injury to the user Before any maintenance procedures are carried out on the system make sure the system is turned off To power off the system follow the steps below Step 1 Locate the Function and Brightness Up function keys See Section 1 2 1 1 Step 2 Hold down the Function and Brightness Up buttons for six seconds to power off the system 5 4 Opening the System 5 4 1 Removing the Back Cover A WARNING
50. HS standards The table below acknowledges the presences of small quantities of certain materials in the product and is applicable to China RoHS only A label will be placed on each product to indicate the estimated Environmentally Friendly Use Period EFUP This is an estimate of the number of years that these substances would not leak out or undergo abrupt change This product may contain replaceable sub assemblies components which have a shorter EFUP such as batteries and lamps These components will be separately marked Please refer to the table on the next page Page 175 Integration Corp AFL2 12A HM65 Series Panel PC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Pb Hg Cd Chromium Biphenyls Diphenyl Ethers CR VI PBB PBDE Printed Circuit Board gt p P P P oe ppp o aen fx JO P fe fe Power Supply Assemblies pe fo J p e pP I This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit requirement in SJ T 11363 2006 X This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above the limit requirement in SJ T11363 2006 Page 176 AFL2 12A HM65 Series Panel PC HILG ERRAT RAFA TE ROHS Fe DFAE L H EH RTE R Artt ROHS FER EE APRE AEE Ra IRE RARI EI ARS GL TAG LS BERRA E TOE
51. Inc BIOS Menu 6 USB Configuration USB Devices The USB Devices Enabled field lists the USB devices that are enabled on the system gt USB Support Enabled Use the USB Support BIOS option to enable USB support gt Enabled DEFAULT USB support enabled gt Disabled USB support disabled gt Legacy USB Support Enabled Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support Normally if this option is not enabled any attached USB mouse or USB keyboard Page 68 Te EN integration AFL2 12A HM65 Series Panel PC does not become available until a USB compatible operating system is fully booted with all USB drivers loaded When this option is enabled any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system gt Enabled DEFAULT Legacy USB support enabled gt Disabled Legacy USB support disabled gt Auto Legacy USB support disabled if no USB devices are connected gt USB 3 0 Support Enabled Use the USB 3 0 Support BIOS option to enable USB 3 0 support gt Enabled DEFAULT USB 3 0 support enabled gt Disabled USB 3 0 support disabled gt XHCI Hand off Enabled Use the XHCI Hand off BIOS option to enable XHCI Hand off support This is a workaround for OSes without XHCI hand off support The XHCI ownership change should be claimed by the XHCI driver gt Enabled DEFAULT XHCI Hand off enabled
52. Min Processor Speed Processor Speed Eeer Cores Intel HT Technology EMT64 Hyper threading Intel Virtualization Technology 206a7 il ZIO IE 800 MHz SCENE 2 Supported Supported Enabled Disabled Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology andDisabled FOR Other OS 40s notr opreimized fOr Hyper Threading Technology When Disabled only one thread per enabled core is enabled EE TY Select Item EnterSelect si Ciao Doc Fl General Help F2 Previous Values F3 Optimized Defaults K Save amp Exit Hoc TEIL Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 4 CPU Configuration The CPU Configuration menu BIOS Menu 4 lists the following CPU details Processor Stepping Lists the CPU processing stepping Microcode Revision Lists the microcode revision Max Processor Speed Lists the Max CPU processing speed Min Processor Speed Lists the Min CPU processing speed Processor Speed Lists the CPU processing speed Processor Cores Lists the number of the processor cores Intel HT Technology Indicates if Intel HT Technology is supported by the CPU EMT64 Indicates if EM64T is supported by the CPU gt Hyper Threading Function Enabled Use the Hyper Threading function to enable or disable the CPU hyper threading function AFL2 12A HM65 Series Panel PC gt Disabled Disables the use of hyper thre
53. Mount Universal Driver 2 1 0 263 Setup Wizard This wizard will guide you through the installation of PenMount Universal Driver V2 1 0 263 It is recommended that you close all other applications before starting Setup This will make it possible to update relevant system Files without having to reboot your computer Click Next to continue Figure 7 17 Touch Screen Driver Welcome Screen Step 6 The License Agreement shown in Figure 7 18 appears Step 7 Click AGREE to accept and continue PenMount Universal Driver V2 1 0 763 Setup License Agreement Please review the license terms before installing PenMount Universal Driver V2 1 0 263 Press Page Down to see the rest of the agreement PLEASE READ THE LICENSE AGREEMENT Pen unt touch screen driver software is only for using with Penl ount touch screen controller or control board Ary person or company using a Den Munt driver on any piece of equipment which does not utilize an Pen M aunt touch screen controller will be prosecuted to the full extent of the law IF you accept the terms of the agreement click I Agree to continue You must accept the agreement to install PenMount Universal Driver 2 1 0 263 Nullsoft Install System 2 45 Ces Figure 7 18 Touch Screen Driver License Agreement Step 8 Browse for an install location or use the one suggested Figure 7 19 Step 9 Click INSTALL to continue Page 105 integration Corp
54. ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password must be 3 to 20 characters long Administrator Password User Password Sola RP assoni Set Master Password FIDO Seem Celerina HDD O KINGOTONToSI Set Setup Administrator Password 5 E Select Screen Select Item parer select El HZ eye F4 E Change Opt General Help Previous Values Optimized Defaults Save amp Exit EXIT Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 19 Security gt Administrator Password Use the Administrator Password field to set or change an administrator password User Password Use the User Password field to set or change a user password gt Set User Password Use the Set User Password field to set or change an HDD user password integration Corp AFL2 12A HM65 Series Panel PC Ai NOTE It is recommended that the system be reset after setting a new HDD password gt Set Master Password Use the Set Master Password field to set or change the master HDD password Ai NOTE It is recommended that the system be reset after setting a new master HDD password gt HDD Password Configuration The HDD 0 KINGSTON SS1 submenu displays the HDD password security features supported by the system Security Supported Yes
55. Security Enabled No Security Locked No Security Frozen No HDD User Pwd Status Not installed HDD Master Pwd Status Installed AFL2 12A HM65 Series Panel PC 6 8 Save amp Exit E e Lt i l Integration ia la Corp v N Ai SX Q Use the Save amp Exit menu BIOS Menu 20 to load default BIOS values optimal failsafe values and to save configuration changes Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Boot SISTER Save amp Exit save Changes and Reset Reset the system after Discard Changes and Reset saving the changes Restore Defaults Save as User Defaults Restore User Defaults Sii 1 de Select Screen Select Item EnterSelect a El Ee Hos F4 ESC Change Opt General Help Prevlous Values Optimized Defaults Save amp Exit EE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 20 Exit gt Save Changes and Reset Use the Save Changes and Reset option to save the changes made to the BIOS options and reset the system gt Discard Changes and Reset Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program gt Restore Defaults Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus F3 key can be used for this operation inte
56. Series Panel PC Debian Replace the TFTP settings from inetd to xinetd and annotate the inetd by adding vi etc inetd conf Modify tftp dgram udp wait root usr sbin as shown below D 6 3 Configure One Key Recovery Server Settings Step 1 Copy the Utility RECOVERYR10 TAR BZ2 package from the One Key Recovery CD to the system server side e B RECOVERYR10 TAR BZ2 bee Archive cl 107 416 EB Step 2 Extract the recovery package to cp RecoveryR10 tar bz2 cd tar xvjf RecoveryR10 tar bz2 Step 3 Copy pxelinux 0 from syslinux and install to tftboot cp usr lib syslinux pxelinux 0 tftpboot Page 163 integration Corp AFL2 12A HM65 Series Panel PC D 6 4 Start the DHCP TFTP and HTTP Start the DHCP TFTP and HTTP For example CentOS service xinetd restart service httpd restart service dhcpd restart Debian etc init d xinetd reload etc init d xinetd restart etc init d dhcp3 server restart D 6 5 Create Shared Directory Step 1 Install the samba yum install samba Step 2 Create a shared directory for the factory default image mkdir share cd share mkdir image cp iel gho image A WARNING The file name of the factory default image must be iei gho Step 3 Confirm the operating system default settings smb conf vi etc samba smb conf Page 164 on Corp Q S Lee Se
57. Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu F1 key General help only for Status Page Setup Menu and Option Page Setup Menu F2 key Load previous values F3 key Load optimized defaults F4 key save changes and Exit BIOS Table 6 1 BIOS Navigation Keys 6 1 3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears To exit the Help Window press Esc or the F1 key again 6 1 4 Unable to Reboot After Configuration Changes If the computer cannot boot after changes to the system configuration are made CMOS defaults Use the jumper described in Chapter 4 6 1 5 BIOS Menu Bar The menu bar on top of the BIOS screen has the following main items Main Changes the basic system configuration Advanced Changes the advanced system settings Chipset Changes the chipset settings Boot Changes the system boot configuration Security Sets User and Supervisor Passwords Save amp Exit Selects exit options and loads default settings The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above Ei Integration Corp S di X gt D D AFL2 12A HM65 Series Panel PC 6 2 Main The Main BIOS menu BIOS Menu 1 appears when the BIOS Setup program is entered The Main menu gives an overview of
58. Step 1 Locate the HDMI connector The location is shown in Chapter 1 Step 2 Align the connector Align the HDMI connector with the HDMI port Make sure the orientation of the connector is correct integration Corp AFL2 12A HM65 Series Panel PC Figure 4 23 HDMI Connection Step 3 Insert the HDMI connector Gently insert the HDMI connector The connector should engage with a gentle push If the connector does not insert easily check again that the connector is aligned correctly and that the connector is being inserted with the right way up me lt gt siti E CH IEn Integration corn d aan AFL2 12A HM65 Series Panel PC Chapter A System Maintenance Page 49 I 5 f integration Corp AFL2 12A HM65 Series Panel PC 5 1 System Maintenance Introduction If the components of the AFL2 12A HM65 fail they must be replaced Components that can be replaced include SO DIMM module WLAN Module Please contact the system reseller or vendor to purchase the replacement parts Back cover removal instructions for the AFL2 12A HM65 are described below 5 2 Anti static Precautions A WARNING Failure to take ESD precautions during the maintenance of the AFL2 12A HM65 may result in permanent damage to the AFL2 12A HM65 and severe injury to the user Electrostatic discharge ESD can cause serious damage to electronic components including the AFL2 12A
59. abled 83 DMICG PUNGCTION TENaDIC sssi aaa 83 BT Function Enabled css asi e 84 Auto Dimming Support Enabled Jc 84 Power Saving Function Disabled ssxsssssssserazzazezze neo zan seni ni eni nienienina 84 DVMT Pre Allocaled ERT 85 DVMT Total Gfx Mem MAL 86 Boot Display DEVICE IM 86 Bootup NumLock State ON EE 87 Quiel Boot E el OO inansa E Ai ARAARA 88 Launch PXE OPROM Disabled 88 Boot Option 1 Generic STORAGE DE iii 88 Hard Drive BBS le e UC 88 Administrator Password ila ii iii 89 User PAS SW H 89 Sel User PASSWOrd icici eee EEEE E 89 Ser Master Pas SWoOrd EE 90 vleit Te EC e BE 90 Save Changes and RESO E 91 Discard Changes and Reegel 91 Restore RT 91 Save as User elastici 92 Restore dR IH TTT 92 Page 129 l Integrationi Corp Appendix D One Key Recovery Page 130 iip l L C arm TN P ES 6 Pe l Integrati AFL2 12A HM65 Series Panel PC a D 1 One Key Recovery Introduction The IEI one key recovery is an easy to use front end for the Norton Ghost system backup and recovery tool This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings Ai NOTE The latest One Key Recovery software provides an auto recovery function that allows a system running Microsoft Windows OS to
60. abled EnterSelect Wir EE ER on Syoyetoulexc Change Opt DMIC tree Enabled BI Func iion Enabled Fl General Help F2 Previous Values F3 Optimized Defaults Auco Dinming support Enabled F4 Save amp Exit Power Saving Function Disabled ESC Exit Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 16 Southbridge Chipset Configuration gt USB Function Enabled Use the USB Function BIOS option to enable or disable USB function support gt Disabled USB function support disabled gt Enabled DEFAULT USB function support enabled Te EN integration AFL2 12A HM65 Series Panel PC gt USB 3 0 Controller Enabled Use the USB 3 0 Controller BIOS option to enable or disable the USB 3 0 controller gt Disabled USB 3 0 controller disabled gt Enabled DEFAULT USB 3 0 controller enabled gt Azalia Enabled Use the Azalia option to enable or disable the High Definition Audio controller gt Disabled The onboard High Definition Audio controller is disabled gt Enabled DEFAULT The onboard High Definition Audio controller automatically detected and enabled gt Azalia Internal HDMI Codec Enabled Use the Azalia Internal HDMI Codec option to enable or disable the HDMI gt Disabled HDMI codec is disabled gt Enabled Derautt HDMI codec automatically detected and enabled gt WIFI Function Enabled Use the WIFI Function option to enable or disable the Wi Fi f
61. ading technology gt Enabled DEFAULT Enables the use of hyper threading technology gt Intel Virtualization Technology Disabled Use the Intel Virtualization Technology option to enable or disable virtualization on the system When combined with third party software Intel Virtualization technology allows several OSes to run on the same system at the same time Disabled DEFAULT Disables the use of Intel Virtualization technology gt Enabled Enables the use of Intel Virtualization technology 6 3 3 SATA Configuration Use the IDE Configuration menu BIOS Menu 5 to change and or set the configuration of the SATA devices installed in the system Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced SATA Controller s Enhanced Determines how SATA SATA Mode Selection IDE controller s operate Serta ATA Porn 0 Empty Software Preserve Unknown Serial ATA Port 1 WDC WD1600BEVT 160 0 Software Preserve SUPPORTED S sealecce Eeer TJ Select Item Enter Select 7 Change No Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESCE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 5 SATA Configuration gt SATA Controller s Enhanced Use the SATA Controller s option to configure the SATA controller AFL2 12A HM65 Series Panel PC gt gt Disabled Disables the on board SATA controller gt Compatible Configures the on
62. al connector Insert the DB 9 connector of a serial device into the DB 9 connector on the RS 422 485 cable Step 3 Secure the connector Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector The DB 9 connector pinouts are listed below AFL2 12A HM65 Series Panel PC Table 4 3 DB 9 Connector Pinouts 4 9 4 USB Device Connection Ai NOTE User must install the USB 3 0 driver before connecting a USB device to the system or else the system may not recognize the connected device There are two USB 2 0 connectors and two USB 3 0 connectors All connectors are located on the bottom panel of the AFL2 12A HM65 To connect a USB device please follow the instructions below Step 1 Locate the USB connectors The locations of the USB connectors are shown in Chapter 2 Step 2 Align the connectors Align the USB device connector with one of the connectors on the bottom panel See Figure 4 22 s IEn Integration Corp AFL2 12A HM65 Series Panel PC Figure 4 22 USB Device Connection Step 3 Insert the device connector Once aligned gently insert the USB device connector into the onboard connector 4 9 5 HDMI Device Connection The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen To connect the HDMI cable to the AFL2 12A HM65 follow the steps below
63. amage to the system Certified Engineers Only certified engineers should install and modify onboard functionalities integration Corp AFL2 12A HM65 Series Panel PC Anti static Discharge If a user open the rear panel of the flat bezel panel PC to configure the jumpers or plug in added peripheral devices ground themselves first and wear and anti static wristband 4 3 Installation and Configuration Steps The following installation steps must be followed Step 1 Unpack the flat bezel panel PC Step 2 Install an HDD Step 3 Configure the system Step 4 Connect peripheral devices to the bottom panel of the flat bezel panel PC Step 5 Mount the flat bezel panel PC 4 4 HDD Installation A WARNING Over tightening back cover screws will crack the plastic frame Maximum torque for cover screws is 5 kg cm 0 36 Ib ft 0 49 Nm To install the HDD into the AFL2 12A HM65 please follow the steps below Step 1 Remove two 2 retention screws from the HDD cover Figure 4 1 B ES e l Iintegration Corp S AFL2 12A HM65 Series Panel PC Figure 4 1 HDD Cover Retention Screws Step 2 Remove the HDD cover from the device Step 3 Loosen the captive screw to release the HDD bracket from the chassis Figure 4 2 Figure 4 2 HDD Bracket Screw integration Corp AFL2 12A HM65 Series Panel PC Step 4 Slide the HDD bracket out of the device as shown Figure 4 3
64. ang for around 10 minutes To use the auto recovery function follow the steps described in the following sections A CAUTION The setup procedure may include a step to create a factory default image It is suggested to configure the system to a factory default environment before the configuration including driver and application installations Step 1 Follow the steps described in Section D 2 1 Section D 2 3 to setup BIOS create partitions and install operating system Step 2 Install the auto recovery utility into the system by double clicking the Utility AUTORECOVERY SETUP exe in the One Key Recovery CD This utility MUST be installed in the system otherwise the system will automatically restore from the factory default image every ten 10 minutes Page 147 AFL2 12A HM65 Series Panel PC AU e SETUP EXE 6 mp AUNG IE rer Figure D 22 Auto Recovery Utility Step 3 Reboot the system from the recovery CD When prompted press any key to boot from the recovery CD It will take a while to launch the recovery tool Please be patient Hindous Proinstalla ee HMMM Figure D 23 Launching the Recovery Tool Step 4 When the recovery tool setup menu appears press lt 4 gt then lt Enter gt ca ie DOS een ya exe HW Execute Ghost Manual Recovery environment For Windows 3 Manual Recovery environment For Linux 4 Auto Recovery environment For Windows bh bat 6 Command Prompt Type
65. audio driver installation begins See Figure 7 15 Realtek High Definition Audio Driver Setup 2 89 R2 40 Setup Status Realtek High Definition Audio Driver is configuring your new software installation C Program Files Realtek Audio Drivers WDMAHDA01 inf install Shield E Laeg T Figure 7 15 Audio Driver Installation Page 103 AFL2 12A HM65 Series Panel PC Step 7 When the installation is complete the screen in Figure 7 16 appears Step 8 Select Yes want to restart my computer now and click Finish Realtek High Definition Audio Driver Setup 2 89 R2 40 Maintenance Complete InstallShield Wizard has finished performing maintenance operations on Realtek High Definition Audio Driver Kg OD Yes want to restart my computer now aa No will restart my computer later a i Remove any disks from their drives and then click Finish to complete setup Install He cack Im PT cancel Figure 7 16 AC 97 Driver Installation Complete 7 6 Touch Screen Driver To install the touch panel software driver please follow the steps below Step 1 Access the driver list See Section 7 2 Step 2 Click Touch Screen Step 3 Locate the setup file and double click on it Step 4 A Welcome Screen appears Figure 7 17 Step 5 Click NEXT to continue Page 104 Corn Z AFL2 12A HM65 Series Panel PC Ze SW d X PenMount Universal Driver V2 1 0 263 Setup Welcome to the Pen
66. ccecescescscescescecescescecescescesees 102 120 TOUCH SCREEN DRIVER scissioni 104 7 0 Calibrating the Touch S TOEN ria 108 7 7 AMCAP DRIVER INSTALLATION ceccececcsceccececcececcececescscscecescscecescecescecesescesescess 110 7 8 USB 3 0 DRIVER INSTALLATION ccccccscecceccscesceccecescescsceecescecescscecescscesescesceseecs 112 A INTERFACE CONNECTORS sssssssssssssssssssssssssssasasas asas aasa aaa aana aaas oaaao a oaaao a a 115 A 1 PERIPHERAL INTERFACE CONNECTORS ccscececcecescececcececesceccscecsescsescesescecesceceses 116 B SAFETY PRECAUTIONS eege 122 B 1 SAFETY PRECAUTIONS alici care ERROR Ei 123 B 1 1 General Safety PreCQutions iii 123 BAI EEN ioni 124 B 1 3 Anti Static Precautions e 124 DIRO i 125 B 2 MAINTENANCE AND CLEANING PRECAUTIONS ccsccsceccsceccececcscecccsceseececescecesees 125 D 24 Maintenance and E 23 DZ 126 C BIOS CONFIGURATION OPTIONS sssssssssssssssssssssssssssssssssassasas asas aasa asas aasa aaa 127 C 1 BIOS CONFIGURATION OPTIONS ccccsccscescceccsccsccecesccscescescescescescescescescescescescens 128 D ONE KEY RECOVERY wsssssssssscssccscssiscdssecascessaccesviasdcacdecsscecdsdesscenddesdededesdecscecssceiceds 130 D 1 ONE KEY RECOVERY INTRODUCTION s sesesesesesnenesesesesesreresesesesseseseresesrereseseseseen 131 EE 132 EES 133 D 2 SETUP PROCEDURE FOR MWUNDOWS Lc eceriece risco risco re vie ce visiere sio ce vie ce vizio rinte 134 Page VIII Te
67. creating the specified partition DISKPART gt assign letter H DiskPFart successfully assigned the drive letter or mount point DISKPART gt create part pri size 18059 DiskPart succeeded in creating the specified partition DISKPART gt assign letter F iDiskPart successfully assigned the drive letter or mount point DISKPART gt exit i I386 SYSTEM32Z format n fsintfs 70 4 The type of the file sugrcem is RAW The new file system is NTFS QuickFormatting 2000M Creating file system structures Format complete 2048254 KB total disk space 2635620 KB are available AsNI386x5YSTEM32 format f e fs intfs sg vi Recovery ry The type of the een CC CAR US KCL UE The new file system is NIFS QuickFormatting 1804M Creating file system structures Format complete 1847474 kB total disk space 1835860 KB are available A 13896 SYSTEM32 exit Figure D 5 Partition Creation Commands sugo ee LE otoeorotion Corp P N N AFL2 12A HM65 Series Panel PC Ai NOTE Use the following commands to check if the partitions were created successfully a TIB6 SYSTEM32 diskpart Microsoft DiskPart version 5 2 3 798 1838 Copyright C 1999 2061 Microsoft Corporation On computer MININT JUC DISKPART gt sel disk A Disk A is now the selected disk DISKPART gt list part Partition HH Type Partition 1 Primary 2460 MB 32 KE Partition 2 Primary 1864 MB 2000 ME DISKPART exit Step
68. ctory default image please configure the system to a factory default environment including driver and application installations To create a factory default image please follow the steps below Step 1 Turn on the system When the following screen displays Figure D 10 press the lt F3 gt key to access the recovery tool The message will display for 10 seconds please press F3 before the system boots into the operating system 3 o boot into recovery mode _ Figure D 10 Press F3 to Boot into Recovery Mode Step 2 The recovery tool menu appears Type lt 4 gt and press lt Enter gt Figure D 11 Z Windows System32 cmd exe i Factory Restore 2 Backup system 3 Restore your last backup 4 Manual 5 Quit Please type the number to select and then press Enter 4 Figure D 11 Recovery Tool Menu Step 3 The About Symantec Ghost window appears Click OK button to continue Page 142 AFL2 12A HM65 Series Panel PC Se Ra Kos SL Kee esae estl 1323 Logg gie L tze Ss C HET Corporation Dapy Ch 1998 2000 8 K R 0 T D FR Ha ml ita era fa Loes ne l plns i rai Br qd ici al ie Coe pry n lae es fla alata e fa U d cbr peurest Ular pg rma ba 1 arewa dl Ise Para le ri Ta Rb e k Tha Licik foggia psi Bra a a Jeeref lo b Tech iral parta waf riri LALA lal 9 BA lishi AT ale a ap hil fap E FA ar bna DELLI wel DFA Sz lva EET ERE Si K 9 Tii Dari
69. ds When you need to dispose of your display products please follow the guidance of your local authority or ask the shop where you purchased the product The mark on electrical and electronic products only applies to the current European Union Member States Please follow the national guidelines for electrical and electronic product disposal B 2 Maintenance and Cleaning Precautions When maintaining or cleaning the AFL2 12A HM65 please follow the guidelines below B 2 1 Maintenance and Cleaning Prior to cleaning any part or component of the AFL2 12A HM65 please read the details below Page 125 AFL2 12A HM65 Series Panel PC Except for the LCD panel never spray or squirt liquids directly onto any other components To clean the LCD panel gently wipe it with a piece of soft dry cloth or a slightly moistened cloth The interior of the AFL2 12A HM65X does not require cleaning Keep fluids away from the AFL2 12A HM65 interior Be cautious of all small removable components when vacuuming the AFL2 12A HM65 Turn the AFL2 12A HM65 off before cleaning the AFL2 12A HM65 Never drop any objects or liquids through the openings of the AFL2 12A HM65 Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the AFL2 12A HM65 Avoid eating drinking and smoking within vicinity of the AFL2 12A HM65 B 2 2 Cleaning Tools Some components in the AFL2 12A HM65 may only be cleaned using a product
70. e NTFS 100006 HB 1951 HB used Ho name from Local drive 80 130179 HB Local file Dei GH0 A firewall or a SELinux is not in use in the whole setup process If there is a firewall or a SELinux protecting the system modify the configuration information to accommodate them g Page 167 Ee T lt ie Il integrationi Corp AFL2 12A HM65 Series Panel PC D 7 Other Information D 7 1 Using AHCI Mode or ALi M5283 VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A the SATA RAID AHCI driver must be installed before using one key recovery Please follow the steps below to install the SATA RAID AHCI driver Step 1 Copy the SATA RAID AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive The SATA RAID AHCI driver must be especially designed for the on board SATA controller Step 2 Connect the USB floppy disk drive to the system Step 3 Insert the One Key Recovery CD into the system and boot the system from the CD Step 4 When launching the recovery tool press lt F6 gt Mindows Preinstallation Environn tin mmm dummm TTT Fress F6 if you need to install a third party SCSI or RAID driver Page 168 at EP gt gt Z k FP E Se Ta A a 4 L s d i Integration Corp AFL2 12A HM65 Series Panel PC mm nce N Step 5 When the following window appears press lt S gt to
71. e You agree to the terms of this Agreement IF you do not wish to so agree do not install or use the Software Please Also Note TF vou are an Original Equipment Manufacturer OEM Independent Hardware vendor THY or Independent Software Vendor 154 this complete LICENSE AGREEMENT applies lt Back Wes No Intel Installation Framework Figure 7 3 Chipset Driver License Agreement Step 10 The Read Me file in Figure 7 4 appears Page 96 SS 92 f l Integrationi Corp AFL2 12A HM65 Series Panel PC Step 11 Click Next to continue Intel Chipset Device Software Intel Chipset Device Software Readme File Information Refer to the Readme File below to view the system requirements and installation information Press the Page Down key to view the rest of the File X XK KKK iii X KK X KK K did dico Product Intel R Chipset Device Software Release Production Version Version 9 0 0 10086 Target Chipset Intel R 4 Series Chipset Date May O1 20086 X TKK hk KKK KKK ETT TEST Kk KKK KK TTP N j x lt Back Cancel Inteli Installation Framework Figure 7 4 Chipset Driver Read Me File Step 12 Setup Operations are performed as shown in Figure 7 5 Step 13 Once the Setup Operations are complete click Next to continue E t Intel Chipset Device Software Intel Chipset Device Software intel Setup Progress Please wait while the Following setup operations are perform
72. ed Installing Driver Intel R 828016 ICH Family USE Universal Host Controller 27 09 Version 6 2 0 1008 Installing Driver Intel R 828016 ICH Family USB Universal Host Controller 27TA Version 9 2 0 1005 Installing Driver Intel R 828016 ICH Family USB Universal Host Controller 27CB Version 6 2 0 1008 Installing Driver Intel R 828016 ICH Family USB2 Enhanced Host Controller ACC Version 6 2 0 1008 Click Next to continue Next Intel Installation Framework Figure 7 5 Chipset Driver Setup Operations Integration Corp AFL2 12A HM65 Series Panel PC Step 14 The Finish screen in Figure 7 6 appears Step 15 Select Yes want to restart this computer now and click Finish Intel Chipset Device Software Intel Chipset Device Software Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the computer now a Yes I want to restart this computer now Mo I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Figure 7 6 Chipset Driver Installation Finish Screen 7 4 Graphics Driver Installation To install the Graphics driver please do the following Step 1 Step 2 Step 3 Step 4 Step 5 Access the driver list See Section 7 2 Click Graphic and select the folder which corresponds to your ope
73. eee cee Sl ms lee cence cee 5 FUNGCHON ISOVS jin tiri lenire 7 AFL2 12A HM65 Rear VieW ssrrrrrririnenee zena ze za aaa eee eee 8 AFL2 12A HM65 UO Interface Panel ssc cesses eee 9 Top Panel viari 9 Figure 1 3 Side ECKE 10 Figure 2 1 AFL2 12A HM65 Dimensions MM sssssssss sss sss sssss sss sss ssesss esse sese ennenen enen 14 Figure 2 2 AFL2 12A HM65 Dimensions MM CONL 11 srrrsire iii 15 Figure 2 3 COM Polls acciai 17 Figure 2 4 RJ 45 Ethernet Connectors sss sss sssssssssssssssssessssssssseeeeoesse eenn aeeoea 17 Figur 2 5 External USB a C 18 FigUre 2 6 ECD SC CGN ioraa EEE EEEE EEEE EEEE EEE 18 FigUure 2 Audiodackti lucca 19 Figure 4 1 HDD Cover Retention SCrews ccccccsssssseeeeeseceesssseeeeeeeeeeensseeeeeeseeeoeenseeeeeseeoenens 29 Figure 4 2 HDD Bracket c TT 29 Figure4 3 Removing the HDD Bracket sss ssssssssssssssssesssseeeese ennenen eenn neee eenn 30 rigure d 4 Iinsering the HDD BE 30 Figure4 5 Securing the TK NEE 31 Figure 4 6 AT ATX Switch Locaion ssssssssssssssssssssssseeeess enesenn ennenen eenn 32 Figure 4 7 Wall mounting Bracket 111 rr 34 Figure 4 8 Chassis Support ScrewS xxrssssscarieeee iena aaa 36 Figure 4 9 Secure the Panel PC 11xxssxss2scsseseeaaazza nana n ae cina iii iii 36 Figure 4 10 Mounting screw location
74. egrationi AFL2 12A HM65 Series Panel PC 4 1 Anti static Precautions A WARNING Failure to take ESD precautions during the maintenance of the AFL2 12A HM65 may result in permanent damage to the AFL2 12A HM65 and severe injury to the user Electrostatic discharge ESD can cause serious damage to electronic components including the AFL2 12A HM65 Dry climates are especially susceptible to ESD It is therefore critical that whenever the AFL2 12A HM65 is accessed internally or any other electrical component is handled the following anti static precautions are strictly adhered to Wear an anti static wristband Wearing a simple anti static wristband can help to prevent ESD from damaging the board Self grounding Before handling the board touch any grounded conducting material During the time the board is handled frequently touch any conducting materials that are connected to the ground Use an anti static pad When configuring the AFL2 12A HM65 place it on an antic static pad This reduces the possibility of ESD damaging the AFL2 12A HM65 Only handle the edges of the PCB When handling the PCB hold the PCB by the edges 4 2 Installation Precautions When installing the flat bezel panel PC please follow the precautions listed below Power turned off When installing the flat bezel panel PC make sure the power is off Failing to turn off the power may cause severe injury to the body and or d
75. elp to prevent ESD from damaging any electrical component Self grounding Before handling any electrical component touch any grounded conducting material During the time the electrical component is handled frequently touch any conducting materials that are connected to the ground Use an anti static pad When configuring or working with an electrical component place it on an antic static pad This reduces the possibility of ESD damage Only handle the edges of the electrical component When handling the electrical component hold the electrical component by its edges Page 124 WW ame 5S E l Integrationi AFL2 12A HM65 Series Panel PC B 1 4 Product Disposal CAUTION Risk of explosion if battery is replaced by and incorrect type Only certified engineers should replace the on board battery Dispose of used batteries according to instructions and local regulations Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cor
76. em Time option to set the system time Manually enter the hours minutes and seconds 6 3 Advanced Use the Advanced menu BIOS Menu 2 to configure the CPU and peripheral devices through the following sub menus A WARNING Setting the wrong values in the sections below may cause the system to malfunction Make sure that the settings made are compatible with the hardware ACPI Settings CPU Configuration SATA Configuration USB Configuration Super IO Configuration HIN Monitor Serial Port Console Redirection jiEi Feature AFL2 12A HM65 Series Panel PC Aprilio Setup Utility Copyright Advanced aib ss ACPI Settings ERNEIEREN E EE EENS UB EE S per REG Coniiguration H M MOni COT Serial Port Console Redirection 1Ei Feature Y Y Y Y Y Y Y Y Version 2 10 120 Copyright BIOS Menu 2 Advanced 6 3 1 ACPI Settings L B E at Integratia Corps abe l w D D E 2010 American Megatrends Inc Security Save amp Exit System ACPI Parameters sz Selisoe Soon tT J Select Item EnterSelect ee Chance opr Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save L Exit HOG Exit 2010 American Megatrends Inc The ACPI Settings menu BIOS Menu 3 configures the Advanced Configuration and Power Interface ACPI options Aptio Setup Utility Copyright Advanced ie ll See wines ACPI Sleep State Version
77. ensseeeseoessseessonenss 65 Intel Virtualization Technology Disabled c sccccssssseeeceeesseeeseeeesseeeseeessseeeseneneees 66 SATA Coniroller s Enhanced 66 SATA Mode Selection IDE ii 67 USB DEVICES e E iii 68 Jee leng LEET E 68 Legacy USB Support Enabled 68 RT ele d E E 69 XHC I Hand off Enabled cerco ranieri ninni arianna 69 EHCI Hand ff Disabled sri 69 Port 60 64 Emulation Enabled isicsariciirinilonciirneninnico narici 70 USB transfer time out Leederen genee EE 70 Device reset time out 20 Sec enesenn ennenen ennenen 70 Device power up delay Auto dla 70 Generic Storage Device 9454 Autos ssssssss essen eenn eenn 71 Serial Port Enabled 72 Change SEHINOS AU 72 Weier 73 CPU Smart Fan control Auto Model sss ssssssssssssssssssssssee seene ennenen 74 Temperature of Start 80 75 Temperature of OF dpr a a aE 75 SEENEN 75 Slope PWM duty 4 PWM dUty iii 75 Console Redirection Disabled irrita 76 Auto Recovery Function Disabled 1 rrrrsiiiiee ennenen eee 77 DVMT Pre Allocated 64M cesses essen 80 DVMT Total Gfx Mem MAX Lai 81 AFL2 12A HM65 Series Panel PC Boot Display Device EFP nine ir iter 81 BengZiRVte DANI et TN 81 USE ele dee ET E EE 82 USB 3 0 Controller Enabled 83 va e E 83 Azalia Internal HDMI Codec Enabled 1 rrrrsiiiiiii iii 83 WIFI Funcion En
78. er applications including ATM Self service kiosk Plant environment monitoring system Factory automation platform Manufacturing shop flow 2 2 Power Adapter The system is shipped with a 100 V to 240 V AC power adapter that has a maximum power output of 65 W The power adapter has a 19 V DC output connector o Rees lt E l Integrationi AFL2 12A HM65 Series Panel PC Chapter 3 Unpacking Page 21 Integration Corp AFL2 12A HM65 Series Panel PC 3 1 Unpacking To unpack the flat bezel panel PC follow the steps below A WARNING The front side LCD screen has a protective plastic cover stuck to the screen Only remove the plastic cover after the flat bezel panel PC has been properly installed This ensures the screen is protected during the installation process Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Use box cutters a knife or a sharp pair of scissors that seals the top side of the external second box Open the external second box Use box cutters a knife or a sharp pair of scissors that seals the top side of the internal first box Lift the monitor out of the boxes Remove both polystyrene ends one from each side Pull the plastic cover off the flat bezel panel PC Make sure all the components listed in the packing list are present 3 1 1 Packing List The AFL2 12A HM65 flat bezel panel PC is shipped with t
79. es Panel PC Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator Driver Readme File Information Refer to the Readme file below to view the system requirements and installation information U CC XX TKK KK XX T Production Version Releases Microsoft Windows 2000 Microsoft Windows XP K lt Back Cancel Intel Installation Framework Figure 7 11 Graphics Driver Read Me File Step 14 Setup Operations are performed as shown in Figure 7 12 SS 92 f l Integrationi Corp Step 15 Once the Setup Operations are complete click Next to continue Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator Driver Setup Progress Please wait while the following setup operations are performed Copying File igxpun exe Copying File difxapi dil Copying File HOMIENU dll Creating Key HKLM System CurrentControlSeti Control windows SystemDirectory C WIND Creating Key HELM System Current ControlSet ServicestialmiDeviced SystemDirectory C yy Creating Key HELM System CurrentContralsetiServicestialmiDevice1 SystemDirectory C UM Creating Key HELMSOFT WARE Microsoft Windows Current ersion Uninstall HOMI DisplayMa Creating Key HELMI SOFTW ARE Microsoft Windows Current ersion Uninstall HDMIT Uninstalls Installing Driver Mobile InteliR 945 Express Chipset Famil Versioni 6 14 10 4926 Intel Installation Framework Figure 7 12 Graphics
80. ete Page 107 Integration Corp AFL2 12A HM65 Series Panel PC 7 6 1 Calibrating the Touch Screen To calibrate the touch screen cursor with the motion of the touch screen pen or finger please follow the steps below Step 1 Make sure the touch screen driver is properly installed Step 2 Locate the PenMount Monitor icon in the bottom right corner of the screen Odi Ch ee NG GL Figure 7 22 PenMount Monitor Icon Step 3 Click the icon A pop up menu appears See Figure 7 23 Control Panel Beep K Right Button Exit Figure 7 23 PenMount Monitor Popup Menu Step 4 Click Control Panel in the pop up menu shown in Figure 7 23 Step 5 The configuration screen in Figure 7 24 appears Page 108 AFL2 12A HM65 Series Panel PC PenMount Control Panel Device Multiple Monitors Tools About Select a device to configure FenMount 9000 R Refresh Figure 7 24 Configuration Screen Step 6 Double click the PenMount 9000 icon as shown in Figure 7 24 Step 7 The calibration initiation screen in Figure 7 25 appears Step 8 Select the Standard Calibration button as shown in Figure 7 25 Device 0 PenMount 9000 R5232 Calibrate Setting Edge Compensation About Advanced Mode Plot calibration data Standard Calibration dvanced Calibration T Turn off EEPROM storage Figure 7 25 Calibration Initiation Screen Step 9 The calibra
81. ett Kl ck rhgb quiet initrd initrd 4 6 25 14 fc9 1606 img itle Hecovery Fartition oot hdd 2 akeactive chainloader 1 Type command title Recovery Partition root hdd 2 makeactive chainloader 1 Step 7 The recovery tool menu appears Figure D 32 Factory Restore Backup system Restore your last backup Manual Quit ase type the number to select and then press Enter Figure D 32 Recovery Tool Menu Step 8 Create a factory default image Follow Step 2 Step 12 described in Section D 2 5 to create a factory default image D 5 H 1 D age 154 e iip 1 E l Integration Corp I N AFL2 12A HM65 Series Panel PC D 5 Recovery Tool Functions After completing the initial setup procedures as described above users can access the recovery tool by pressing lt F3 gt while booting up the system However if the setup procedure in Section D 3 has been completed and the auto recovery function is enabled the system will automatically restore from the factory default image without pressing the F3 key The recovery tool main menu is shown below lca X Windows System32 cmd exe 1 Factory Restore 2 Backup system 3 Restore your last backup 4 Manual 5 Quit Please type the number to select and then press Enter Figure D 33 Recovery Tool Main Menu The recovery tool has several functions including 1 Factory Restore Res
82. get install dnco3 server Debian commands marked in blue Confirm the operating system default settings dhcpd conf CentOS Use the following command to show the DHCP server sample location vi etc dhcpd conf The DHCP server sample location is shown as below CP Server Configuration file fusr share doc dhe D d d hcnd cont samp le Use the following command to copy the DHCP server sample to etc dhcpd conf cp usr share doc dhcp 3 0 5 dhcpd conf sample etc dhcpd conf vi etc dhcpd conf ER d il a Lei Debian vi etc dhcpd conf Edit etc dhcpd conf for your environment For example add next server PXE server IP address Page 161 o ei integration Corp e AFL2 12A HM6 filename pxelinux 0 Eastern Standard me D 6 2 Configure TFTP Settings Step 1 Install the tftp httpd and syslinux yum install tftp server httpd syslinux CentOS apt get install tftpd hpa xinetd syslinux Debian Step 2 Enable the TFTP server by editing the etc xinetd d tftp file and make it use the remap file The vvv is optional but it could definitely help on getting more information while running the remap file For example CentOS vi etc xinetd d tftp Modify disable no server_args S tftpboot m tftpboot tftpd remap vvv_ Page 162 T 3 N ef a el ech WT Corp wp N X Oe T E l Integrati AFL2 12A HM65
83. gration Corp AFL2 12A HM65 Series Panel PC gt Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults gt Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options ka r lt spe E ds l Integration a AFL2 12A HM65 Series Panel PC Jp X gt Chapter l Software Drivers Page 93 integration Corp AFL2 12A HM65 Series Panel PC 7 1 Available Software Drivers Ai NOTE The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice Visit the IEI website or contact technical support for the latest updates The following drivers can be installed on the system Chipset Graphic Audio Touch Screen AMCap USB 3 0 Installation instructions are given below 7 2 Starting the Driver Program To access the driver installation programs please do the following Step 1 Insert the CD ROM that came with the system into a CD ROM drive attached to the system Step 2 Click AFL2 12A HM65 Step 3 A list of available drivers appears 7 3 Chipset Driver Installation To install the chipset driver please do the following Step 1 Access the driver list See Section 7 2 Step 2 Click Chipset Page 94 AFL2 12A HM65 Series Panel PC Step 3 Locate the setup file and do
84. gt CPU Smart Fan control Auto Mode Use the CPU Smart Fan control BIOS option to configure the CPU Smart Fan gt Full Mode Fan is on all the time AFL2 12A HM65 Series Panel PC Manual Mode by The fan spins at the speed set in PWM Fan PWM control Auto Mode DEFAULT The fan adjusts its speed using these settings Temp Limit of OFF Temp Limit of Start Fan Start PWM Slope PWM 1 gt Temperature of Start 80 The Temperature of Start field allows user to set the starting temperature using the and keys gt Temperature of Off 75 The Temperature of Off field allows user to set the off temperature using the and keys gt Start PWM 30 The Start PWM field allows user to set the start PWM speed using the and keys gt Slope PWM duty 4 PWM duty The Slope PWM duty field allows user to set the slope fan speed 6 3 7 Serial Port Console Redirection The Serial Port Console Redirection menu BIOS Menu 11 allows the console redirection options to be configured Console redirection allows users to maintain a system remotely by re directing keyboard input and text output through the serial port AFL2 12A HM65 Series Panel PC Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced COMI Console Redirection Console Redirection Disabled Enable or Disable gt Console Redirection Settings COM3 Comsole Redirection Di cabled e Select Sereen
85. gure the boot display device gt HDMI DEFAULT Sets the boot display device to HDMI gt LFP Sets the boot display device to LFP io t aoe Pe Ex integration Corp Ni fa X 7 Q AFL2 12A HM65 Series Panel PC 6 6 Boot Use the Boot menu BIOS Menu 18 to configure system boot options Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Security Save amp Exit EE ee select the keyboard Bootup NumLock State On NumLock state Quiet Boot Enabled Launch PXE OpROM Disabled Colleen Boot Option Priorities T J Select Item Boot Option 1 Generic STORAGE DE FnterSelect Sn uo doo Ploppy Drive BBS Priorities Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit o che Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 18 Boot gt Bootup NumLock State On Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up gt On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up This allows the immediate use of the 10 key numeric keypad located on the right side of the keyboard To confirm this the Number Lock LED light on the keyboard is lit gt Off Does not enable the keyboard Number Lock automatically To use the 10 keys on the keyboard press the Number Lock key located o
86. he RJ 45 connector on the bottom panel and provides external GbE connectivity 2 4 3 External USB Connectors There are two USB 2 0 connectors and two USB 3 0 connectors on the bottom panel of the AFL2 12A HM65 All USB connectors are interfaced directly to the USB controllers on the HM65 southbridge All USB connectors are fully compliant with USB specification Revision 2 0 and USB specification Revision 1 1 and can be interfaced to both USB 1 1 Page 17 E GL Corp Integration Corp AFL2 12A HM65 Series Panel PC and USB 2 0 compliant devices Only USB 3 0 connectors are compatible with USB 3 0 devices un w fed de ke Be o O o n 2 DA N o o o N 5 3 T E E Figure 2 5 External USB Ports 2 5 Touchscreen LCD 2 5 1 Monitor A 12 1 LCD screen is installed on the front of the AFL2 12A HM65 The screen is shown in Figure 2 6 below Webcam TouchScreen ABS Plastic Frame RFID Sensor Figure 2 6 LCD Screen B ES e l Iintegration Corp AFL2 12A HM65 Series Panel PC 2 5 2 Touch Screen Module A controller for the touch screen is installed on the motherboard The sensitive touch screen is accurate reliable and durable 2 6 Audio 2 6 1 Audio Codec Controller The integrated HD Audio compliant audio controller on the Intel HM65 Southbridge is integrated to a Realtek ALC888 audio codec The Realtek ALC888 is connected to an external a
87. he following components sae es Standard 1 AFL2 12A HM65 panel PC Te EN integration AFL2 12A HM65 Series Panel PC Power adapter P N 63040 010090 030 RS Power cord P N 32702 000401 100 RS Power transfer cord P N 32000 089400 RS M3 Screws Pack M4 Screws Pack e EREM Touch Pen RJ 45 to DB 9 COM Port Cable 4 4 1 P N 32005 000200 200 RS 1 RS 422 cable P N 32205 002400 100 RS IR Remote Control P N 7Z000 SLPCB005 RS User manual CD and driver CD One Key Recovery CD P N 7B000 000724 RS Wall mounting kit P N AFLWK 19 AFLWK 19B Arm P N ARM 11 RS Stand P N STAND A12 V Stand P N VSTAND A12 Hybrid Card Reader P N AFL2P 12AMSI U R10 Magnetic Stripe Reader P N AFL2P 12AMSR U R10 Rack Mounting Kit P N AFL2RK 12 OS Win CE 6 0 128MB CF Card P N AFL2CF 12 HM65 CE060 128M R10 AFL2 12A HM65 Series Panel PC AFL2 12A HM65 Series Panel PC OS Win XPE 2GB CF Card P N AFL2CF 12 HM65 XPE 2G R10 OS Win XPE 4GB CF Card P N AFL2CF 12 HM65 XPE 4G R10 OS Linux 2GB CF Card P N AFL2CF 12A HM65 LNX R10 OS Win 7 Embedded 4GB CF Card P N AFL2CF 12 HM65 WES7P 4G R10 AFL2CF 12 HM65 WES7E 4G R10 If any of these items are missing or damaged contact the distributor or sales representative immediately Chapter 4 Installation Page 26 WW gue Se E l Int
88. ings of the AFL2 12A HM65 If considerable amounts of dust water or fluids enter the AFL2 12A HM65 turn off the power supply immediately unplug the power cord and contact the AFL2 12A HM65 vendor DONOT O Drop the AFL2 12A HM65 against a hard surface O Strike or exert excessive force onto the LCD panel Touch any of the LCD panels with a sharp object O In a site where the ambient temperature exceeds the rated temperature Page 123 e IE l Iintegration Corp AFL2 12A HM65 Series Panel PC B 1 2 CPU Temperature Warning A WARNING When the CPU s core temperature reaches TJ Max the CPU temperature alert LED turns RED and the CPU starts to lower its clock speed At this moment the user must lower the environments temperature or close some running applications to cool down the CPU B 1 3 Anti static Precautions A WARNING Failure to take ESD precautions during the installation of the AFL2 12A HM65 may result in permanent damage to the AFL2 12A HM65 and severe injury to the user Electrostatic discharge ESD can cause serious damage to electronic components including the AFL2 12A HM65 Dry climates are especially susceptible to ESD It is therefore critical that whenever the AFL2 12A HM65 is opened and any of the electrical components are handled the following anti static precautions are strictly adhered to Wear an anti static wristband Wearing a simple anti static wristoand can h
89. m will install the Intel Graphics Media Accelerator Driver onto this computer It is strongly recommended that you exit all programs before continuing Click Next to continue Cancel Intel Installation Framework Figure 7 9 Graphics Driver Welcome Screen Step 10 The License Agreement in Figure 7 10 appears Step 11 Click Yes to accept the agreement and continue Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator Driver License Agreement YOU must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IM DM Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Software you agree to the terms of this Agreement IF you do not wish to so agree do not install or use the Software Please Also Note TF vou are an Original Equipment Manufacturer OEM Independent Hardware Vendor HM or Independent Software Vendor 15 this complete LICENSE AGREEMENT applies lt Back Ves No Intel Installation Framework Figure 7 10 Graphics Driver License Agreement Step 12 The Read Me file in Figure 7 11 appears Step 13 Click Next to continue Page 100 AFL2 12A HM65 Seri
90. n the upper left hand corner of the 10 key pad The Number Lock LED on the keyboard lights up when the Number Lock is engaged integration Corp AFL2 12A HM65 Series Panel PC gt Quiet Boot Enabled Use the Quiet Boot BIOS option to select the screen display when the system boots gt Disabled Normal POST messages displayed gt Enabled DEFAULT OEM Logo displayed instead of POST messages gt Launch PXE OpROM Disabled Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices gt Disabled DEFAULT Ignore all PXE Option ROMs gt Enabled Load PXE Option ROMs gt Boot Option 1 Generic STORAGE DE Use Boot Option 1 to enable or disable booting from the detected drive gt Generic DEFAULT Enables booting from the detected storage STORAGE DE device gt Disabled Disables boot option gt Hard Drive BBS Priorities Use Hard Drive BBS Priorities option to set the system boot order AFL2 12A HM65 Series Panel PC 6 7 Security SS 92 Lt f l Iintegratio e d e Cor AEN ne Use the Security menu BIOS Menu 19 to set system and user passwords Aptio Setup Utility Copyright C 2010 American Megatrends Inc Save amp Exit Main Advanced Chipset Boot Security Password Description If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If
91. ndby mode when it is turned off The panel PC can be easily turned on via network or a power switch in standby mode Remote power control is perfect for advertising applications since the broadcasting time for each panel PC can be set individually and controlled remotely Other possible application includes Security surveillance Point of Sale POS Advertising terminal E L E E EN integratio AFL2 12A HM65 Series Panel PC 4 6 Powering On the System To power on the system follow the steps below Step 1 Locate the Function and Brightness Up function keys See Section 1 2 1 1 Step 2 Hold down the Function and Brightness Up buttons for three seconds to power on the system 4 7 Powering Off the System To power off the system follow the steps below Step 1 Locate the Function and Brightness Up function keys See Section 1 2 1 1 Step 2 Hold down the Function and Brightness Up buttons for six seconds to power off the system 4 8 Mounting the System A WARNING When mounting the flat bezel panel PC onto an arm onto the wall or onto a panel it is better to have more than one person to help with the installation to make sure the panel PC does not fall down and get damaged The four methods of mounting the AFL2 12A HM65 are listed below Wall mounting Stand mounting Arm mounting Rack mounting The four mounting methods are described below integration Corp
92. ng the WLAN Card cca 56 Figure5 7 Attaching the Antennas sss ssssss sese eess sees sees s sse eess enesenn ennenen ennenen enne 57 Figure 7 1 Chipset Driver SC CEM csi iii iaia 95 Figure 7 2 Chipset Driver Welcome Screen cccssssss sese s essen eenn eenn eee 96 Figure 7 3 Chipset Driver License Agreement 11 rrrrsiiiirii iii 96 Figure 7 4 Chipset Driver Read Me File rr ennenen ennenen ennenen 97 Figure 7 5 Chipset Driver Setup Operations ssssssss sss sese s esse sese eee 97 Figure 7 6 Chipset Driver Installation Finish Screen rin 98 Figure 7 7 Graphics Driver Read Me File sss ssssssssssssssssseessseennne EEN 99 Figure 7 8 Graphics Driver Setup Files Extracted ccccccsssssseeeeseesseeeseeessseeeseeesnseesseoeees 99 Figure 7 9 Graphics Driver Welcome Screen cssssss sss sees essen ennenen 100 Figure 7 10 Graphics Driver License Agreement sssssssssssssseecssssssss eee eenn eenn ee 100 Figure 7 11 Graphics Driver Read Me FIle retti 101 Figure 7 12 Graphics Driver Setup OperationS 11rrrrssneii ieri ie eee 101 Figure 7 13 Graphics Driver Installation Finish Screen rr 102 Figure 7 14 Audio Driver Welcome Screen senenn eenn neee eenn 103 Figure 7 15 Audio Driver Installation cca 103 Figure 7 16 AC 97 Driver Installation Comple
93. om a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system the server through LAN connectivity after encountering a Blue Screen of Death BSoD or a hang for around 10 minutes To be able to use this function the client system and the Linux system MUST reside in the same domain el Client E a H EI f FT a to e f a va Server Ai NOTE The supported client OS includes Windows 2000 Windows 7 Windows XP Windows CE Windows Vista Windows XP Embedded Prior to restoring client systems from a Linux server a few setup procedures are required Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Configure DHCP server settings Configure TFTP settings Configure One Key Recovery server settings Start DHCP TFTP and HTTP Create a shared directory Setup a client system for auto recovery The detailed descriptions are described in the following sections In this document two types of Linux OS are used as examples to explain the configuration process CentOS 5 5 Kernel 2 6 18 and Debian 5 0 7 Kernel 2 6 26 Page 160 AFL2 12A HM65 Series Panel PC 5 T i le N D By a a a s i si Corp h Oe E l Iintegrati D 6 1 Configure DHCP Server Settings Step 1 Step 2 Install the DHCP yum install dhcp CentOS commands marked in red apt
94. or El General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC H E 2010 American Megatrends Inc BIOS Menu 17 Graphics Configuration gt DVMT Pre Allocated 64M Use the DVMT Pre Allocated BIOS option to configure the CPU Smart Fan gt oM 32M 64M 96M 128M 160M 192M 224M 256M 288M 320M d 4 4 Vv d dede d 352M DEFAULT DVMT memory size set at 0 MB DVMT memory size set at 32 MB DVMT memory size set at 64 MB DVMT memory size set at 96 MB DVMT memory size set at 128 MB DVMT memory size set at 160 MB DVMT memory size set at 192 MB DVMT memory size set at 224 MB DVMT memory size set at 256 MB DVMT memory size set at 288 MB DVMT memory size set at 320 MB DVMT memory size set at 352 MB e ka ili b l Integration io eme Corp integration Corp AFL2 12A HM65 Series Panel PC gt 384M DVMT memory size set at 384 MB gt 416M DVMT memory size set at 416 MB gt 448M DVMT memory size set at 448 MB gt 480M DVMT memory size set at 480 MB gt 512M DVMT memory size set at 512 MB gt DVMT Total Gfx Mem MAX Use the DVMT Total Gfx Mem BIOS option to configure the DVMT total graphics memory size gt 128M Sets the DVMT Total Gfx Mem size to 128 MB gt 256M Sets the DVMT Total Gfx Mem size to 256 MB gt MAX DEFAULT Sets the DVMT Total Gfx Mem size to maximum gt Boot Display Device HDMI Use the Boot Display Device BIOS option to confi
95. pe lt 3 gt and press lt Enter gt in the main menu Step 2 The Symantec Ghost window appears and starts to restore the last backup image iei_user GHO Symantec Ghost 11 5 Copyright C 1998 2008 Symantec Corporation fill rights reserved Type CHTFS 100006 AB 1951 HE used Ho name from Local drive 1 152627 HE Local file D iei_user gho Figure D 38 Restore Backup Step 3 The screen shown in Figure D 39 appears when backup recovery is complete Press any key to reboot the system Page 158 e EE e di AFL2 12A HM65 Series Panel PC ca K Windows System32 cmd exe i Factory Restore 2 Backup system 3 Restore your last backup 4 Manual 5 Quit Please type the number to select and then press Enter 3 Recovery complete Press any key to continue m Figure D 39 Restore System Backup Complete Window D 5 4 Manual To restore the last system backup please follow the steps below Step 1 Type lt 4 gt and press lt Enter gt in the main menu Step 2 The Symantec Ghost window appears Use the Ghost program to backup or recover the system manually Sumantee Ghost 1 1 5 Copyright CI 1998 2008 Symantec Corporation All rights resenred Figure D 40 Symantec Ghost Window Step 3 When backup or recovery is completed press any key to reboot the system Page 159 Integration Corp AFL2 12A HM65 Series Panel PC D 6 Restore Systems fr
96. r iii 22 rI RPPEACING COMPONENT iper 53 5 5 1 Memory Module Replacement iii 53 WWDC liana 54 S SENS 1 ATI TIE C OVER eerste ce espe ia a 57 DALL BIOS SETUP grani 58 EE 59 KE EE 59 S EE E 59 EE eege 60 6 1 4 Unable to Reboot After Configuration ChangesS ii 60 04 E bian 60 PANI RR A 61 CADONO aa a E n 62 GACE SCI S iii 63 032 CPU E 64 6 3 3 SATA Configuration irritati 66 OSTO EE 68 OD SUPE TO CON CUT Ln 71 6 52 Seral Port ENER Ee le E J2 OROA On OT siii 73 POL Fan e Ee E 74 6 3 7 Serial Port Console Redirection iii 75 SCENE 71 Ee a E E E 78 CONIARE 79 6 5 1 1 Graphics Confeuraton 80 6 3 2 South Bridge RE 82 63 3 Graphics Configuratio prin 84 Te Integration Corp AFL2 12A HM65 Series Panel PC cE ee WEEN 87 6 7 SECURITY cccccceccccoccecceccsccceccececceccecescecsscuscesssceecessecuscescsceecscectsceecestscasceseesascuseeses 89 6 8 SAVE amp EXIT ccccccccecccccccecceccsccceccscecceccscescescecaecescecuscesceceececestecescesescasceseecasceseeces 9 7 SOFTWARE DRIVERS ee 93 7 1 AVAILABLE SOFTWARE DRIVERS ivi ceci ricci re riore riore riore visiere ieri sie ce vie ce risco rezioneni 94 7 2 STARTING THE DRIVER PROGRAM sssesesesessssesesesesesreseseseseseereseseseseereneseseseerereseseseens 94 7 3 CHIPSET DRIVER INSTALLATION 94 7 4 GRAPHICS DRIVER INSTALLATION 98 7 5 AUDIO DRIVER INSTALLATION ccceccscoccecceccsccceccecesce
97. rating system Double click the setup file The Read Me file in Figure 7 7 appears Click Next to continue se SAER ds l Iintegratio orp Ei D D AFL2 12A HM65 Series Panel PC e Intel R Chipset Graphics Driver Software InstallShield Wizard EHE RAE HR RR EE EE EE EEE EE EE EE EER EE EE A Li a da cla di cia a da ee a v a da aN Production version Releases Microsoft Windowst 2000 Microsoft Windows Zb Driver Revision Production Version 14 32 4 Package 45665 Graphics 6 14 10 4926 HDMI Audio 5 10 0 1030 February 28 2008 MOTE This document refers to systems containing e to X E KF FF FF E Following Intek Di chipsets Ui A Figure 7 7 Graphics Driver Read Me File Step 6 The installation files are extracted See Figure 7 8 Step 7 Click Next to continue Z Intel R Chipset Graphics Driver Software InstallShield Wizard Extracting Files The contents of this package are being extracted Please wait while the InstallShield Wizard extracts the files needed to install Intel R Chipset Graphics Driver Software on your computer This may take a few moments Reading contents of package E InstallShield Cancel Figure 7 8 Graphics Driver Setup Files Extracted Step 8 The Welcome Screen in Figure 7 9 appears Step 9 Click Next to continue AFL2 12A HM65 Series Panel PC Welcome to the Setup Program This setup progra
98. rature alert LED turns red and the CPU starts to lower its clock speed At this moment the user must lower the environments temperature or close some running applications to cool down the CPU 1 2 1 2 Function Keys The Function Keys are located under the bottom right hand corner of the LCD screen Figure 1 4 AFL2 12A HM65 Series Panel PC Figure 1 4 Function Keys The Function Keys are described in Table 1 3 Fn Brightness Up Power On Off Note To power on the system hold down the Fn Brightness Up buttons for 3 seconds To power down the system hold down the FN Brightness Up buttons for six seconds Table 1 3 Function Key Descriptions 1 2 2 Rear Panel The rear panel provides access to retention screw holes that support the wall mounting Refer to Figure 1 5 integration Corp AFL2 12A HM65 Series Panel PC 100 mm Figure 1 5 AFL2 12A HM65 Rear View 1 2 3 I O Interface Panel The I O interface panel located on the bottom of the AFL2 12A HM65 has the following features 1x Audio jack 1x 9V 36V DC IN power jack 1x HDMI port 1x RS 232 DB 9 connector 1x RS 422 485 connector 1x GbE connector 2x USB 2 0 connectors 2x USB 3 0 connectors 1x Power switch 1x Reset button 1x Clear CMOS switch 1x AT ATX Switch 6x Function Keys e ly i K ROLE E l Integration AFL2 12A HM65 Series Panel PC The external
99. rowse and select another folder Click Install to start the installation Destination Folder E Program Files del Danjou amp MCap Space required 610 0KB Space available 40 066 GC ap Installer Figure 7 28 AMCap Driver Choose Install Location Step 8 The program begins to install Page 111 integration Corp AFL2 12A HM65 Series Panel PC Step 9 When the driver installation is complete the screen in Figure 7 29 appears Step 10 Click Finish to save and exit S AMCap Setup Completing the AMCap Setup Wizard AMC ap has been installed on your computer Click Finish to close this wizard Show Readme Application Website Figure 7 29 AMCap Driver Installation Complete 7 8 USB 3 0 Driver Installation To install the USB 3 0 driver please do the following Step 1 Access the driver list See Section 7 2 Step 2 Click USB 3 0 and select the folder which corresponds to your operating system Step 3 Double click the setup file Step 4 The Welcome Screen in Figure 7 30 appears Step 5 Click Next to continue Page 112 SS 92 f l Iintegrationi Corp AFL2 12A HM65 Series Panel PC ix Fresco Logic USB3 0 Host Controller Setup Welcome to the Fresco Logic USB3 0 Host Controller 3 3 35 0 Setup Wizard The Setup Wizard will install Fresco Logic USB3 0 Host Controller on your computer Click Next to continue or Cancel to exit the Setup Wizard
100. select Specify Additional Device Setup could wot deternine the type of one or nore mass storage devices installed in your system or you have chosen to manually specify an adapter Currently Setup will load support for the following mass storage devices s none 3 To specify additional SCS adapters CD ROM drives or special disk controllers for use with Windows including those for which you have a device support disk fron a mass storage device manufacturer press 5 If you do not have any device support disks from a mass storage device manufacturer or do not want to specify additional nass storage devices for use with Windows press ENTER S Specify Additional Device ENTER Continue F3 Exit Step 6 In the following window select a SATA controller mode used in the system Then press lt Enter gt The user can now start using the SATA HDD fou have chosen to configure a SCS Adapter for use ulih Windows using a device support disk provided by an adapter manufacturer Select the SCSI Adapter you want fron the following list or press ESC to return to the previous screen VIA V RAID Controller Ser les Hindous XP RU283 x64 VIA V RAID Controller Series Mindows 2 VIA V RAID Controller Serles Windows N14 ENTER Select cD T Page 169 integration Corp AFL2 12A HM65 Series Panel PC Step 7 After pressing lt Enter gt the system will get into the recovery tool setup menu Continue to follow the
101. setup procedure from Step 4 in Section D 2 2 Create Partitions to finish the whole setup process D 7 2 System Memory Requirement To be able to access the recovery tool by pressing lt F3 gt while booting up the system please make sure to have enough system memory The minimum memory requirement is listed below Using Award BIOS 128 MB system memory Using AMI BIOS 512 MB system memory Page 170 Appendix Watchdog Timer Page 171 integration Corp AFL2 12A HM65 Series Panel PC Ai NOTE The following discussion applies to DOS environment IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems e g Windows and Linux The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash This condition may have occurred by external EMI or a software bug When the CPU stops working correctly Watchdog Timer either performs a hardware reset cold boot or a Non Maskable Interrupt NMI to bring the system back to a known state A BIOS function call INT 15H is used to control the Watchdog Timer INT 15H AH 6FH Sub function Sets the Watchdog Timer s period Time out value Its unit second is dependent on the item Watchdog Timer unit select in CMOS setup Table E 1 AH 6FH Sub function Call sub function 2 to set the time out period
102. system i Execute Ghost Manual Recovery environment For Windows d Manual Recovery environment For Linux i fiuto Recovery environment For Windows b5 Exit 6 Command Prompt Type the number to print text 4 Press any key to continue Figure D 28 Press any key to continue Step 9 Eject the One Key Recovery CD and restart the system Step 10 Press the lt DELETE gt key as soon as the system is turned on to enter the BIOS Step 11 Enable the Auto Recovery Function option Advanced gt iEi Feature gt Auto Recovery Function Page 150 e iS p dai Integration corp Se AFL2 12A HM65 Series Panel PC 7 NN WW EE ER Ee kee Advanced PENE Boot Security Chipset KS 1El Feature Auto Recovery Function Enabled Recover from PXE Disabled Sei l _ w av Select Item Enter Go to SubScreen ol General Help F10 Save and Exit ESC Ei v02 61 Copyright 1985 2006 American Megatrends Inc BIOS Menu 21 IEI Feature Step 12 Save changes and restart the system If the system encounters a Blue Screen of Death BSoD or a hang for around 10 minutes it will automatically restore from the factory default image Ad CAUTION The auto recovery function can only apply on a Microsoft Windows system running the following OS versions Windows XP Windows Vista Windows 7 D 4 Setup Procedure for Linux The initial setup procedure for Linux system is mostly the same
103. t Configuration AFL2 12A HM65 Series Panel PC 6 5 1 1 Graphics Configuration The Graphics Configuration submenu BIOS Menu 9 allows user to configure graphics settings Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced Graphics Configuration Select DVMT 5 0 Pre Allocated Fixed DVMT Pre Allocated 64M Graphics Memory size DVMT Total Gfx Mem MAX used by the Internal Graphics Device Boot Display Device LFP LCD Panel Type 1024x768 TSBIT ss Select Screen TL Select Item EnterSelect SE a Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESCE Tie Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 15 Hardware Health Configuration gt DVMT Pre Allocated 64M Use the DVMT Pre Allocated BIOS option to configure the CPU Smart Fan gt om DVMT memory size set at 0 MB gt 32M DVMT memory size set at 32 MB gt 64M DEFAULT DVMI memory size set at 64 MB gt 96M DVMT memory size set at 96 MB gt 128M DVMT memory size set at 128 MB gt 160M DVMT memory size set at 160 MB vo IEE integration AFL2 12A HM65 Series Panel PC gt 192M DVMT memory size set at 192 MB gt 224M DVMT memory size set at 224 MB gt 256M DVMT memory size set at 256 MB gt 288M DVMT memory size set at 288 MB gt 320M DVMT memory size set at 320 MB gt 352M DVMT memory size set at 352 MB gt 384M DVMT memory size set at 384 MB
104. t the RJ 45 to COM port cable to the panel PC Insert the RJ 45 connector end of cable into the RJ 45 serial port See Figure 4 18 Step 3 Connect the serial device Connect a serial device to the DB 9 connector end of the cable See Figure 4 18 AFL2 12A HM65 Series Panel PC pe KI n n 6 X x NI path VE quel SZ ma A 4 Figure 4 18 RJ 45 Serial Port Connector Step 4 Secure the connector Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector 4 9 3 RS 422 485 Serial Port Connection CN Label COM6 CN Type 4 pin connector CN Location See Figure 4 19 CN Pinouts See Table 4 2 and Figure 4 20 A RS 422 485 serial port device can be connected to the RS 422 485 serial port on the bottom panel The pinouts of the RS 422 485 serial port are shown below 1 3 2 4 Figure 4 19 RS 422 485 Serial Port Te B amp k SS N En Integration Corp AFL2 12A HM65 Series Panel PC Table 4 2 RS 422 485 Serial Port Pinouts To install the RS 422 485 devices follow the steps below Step 1 Locate the RS 422 RS485 connector The location of the RS 422 RS 485 connector is shown in Figure 1 6 Step 1 Connect the RS 422 485 connector to the RS 422 485 cable The RS 422 485 cable can be found in the packing list and is shown in Figure 4 20 Figure 4 20 RS 422 485 Cable Step 2 Insert the seri
105. t the recovery CD Step 4 Turn on the system Step 5 Press the lt DELETE gt key as soon as the system is turned on to enter the BIOS Step 6 Select the connected optical disk drive as the 1 boot device Boot gt Boot Device Priority gt 17 Boot Device Step 7 Save changes and restart the computer Continue to the next section for instructions on partitioning the internal storage D 2 2 Create Partitions To create the system backup the main storage device must be split into two partitions three partitions for Linux The first partition will be for the operating system while the second partition will be invisible to the operating system and contain the backup made by the one key recovery software Step 1 Putthe recovery CD in the optical drive of the system Step 2 Boot the system from recovery CD When promoted press any key to boot from the recovery CD It will take a while to launch the recovery tool Please be patient Page 135 AFL2 12A HM65 Series Panel PC Hindous Proinstallation Eaviro MMMM Figure D 2 Launching the Recovery Tool Step 3 The recovery tool setup menu is shown as below CA BS Ee exe i Execute Ghost Z Manual Recovery environment For Windows i3 Manual Recovery environment For Linux 4 fiuto Recovery environment For Windows Exit 6 Command Prompt Type the number to print text Figure D 3 Recovery Tool Setup Menu Step 4 Press lt 6 gt then lt Enter gt
106. tallation Complete Page 114 s r E K B r pene gt siti E ndl LS l integration Na m WE AFL2 12A HM65 Series Panel PC A X Appendix A Interface Connectors Page 115 AFL2 12A HM65 Series Panel PC A 1 Peripheral Interface Connectors The AFL2 12A HM65 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers The pinouts for these connectors are listed below Table A 4 Speaker Connector CN8 Pinouts Page 116 AFL2 12A HM65 Series Panel PC PWRBTN_SW DATA5 DATA5 Table A 7 RFID COM Connector RFID_COM1 Pinouts PIN NO DESCRIPTION PIN NO DESCRIPTION KEYLED1 KEYLED2 1 WW apro 5 E l Iintegrationi Table A 8 Hotkey LED Connector HOTKEYLEDCN1 Pinouts Fre scuo pn no esca _ Iess Ji eso R DS Ee Table A 9 Hotkey Connector HOTKEYCN1 Pinouts Page 117 AFL2 12A HM65 Series Panel PC WW seggio E E E l Iintegratio AFL2 12A HM65 Series Panel PC o pee p pe Table A 14 LED Connector LEDCN1 Pinouts EH pa wo scuo _ M E e eso 7 een e cere sume fo een CE Table A 15 EC Debug Connector CN4 Pinouts Fre esca n no esca _ EN O Im eroe fe amo AUTO DATA Table A 16 Auto dimming Connector JP6 Pinouts DESCRIPTION Table A 17 SATA Power Connector CN5 Pinouts Page 119 AFL2 12A HM65 Series Panel
107. te 1 srrrrrrreea iii 104 Figure 7 17 Touch Screen Driver Welcome Screen 221 rr rrrrreeaiiiiiiiieiieennno 105 Figure 7 18 Touch Screen Driver License Agreement 221rrrrssrriieree iii 105 Figure 7 19 Touch Screen Driver Choose Install Location 1rrrrrrtt 106 Figure 7 20 Touch Screen Driver Installation SCreen esse eee esee eenn 107 Figure 7 21 Touch Screen Driver Update Complete 1sssrrrrereeeezzzzanene 107 i oe Li E l Integration adi WW Integration Corp AFL2 12A HM65 Series Panel PC Figure 7 22 PenMount Monitor ICON sis csiewansccessnticannan cnecdvaaseneedcasutirensunehenisneusemeeveeuwanseuvbeenenieueeece 108 Figure 7 23 PenMount Monitor Popup MENU rr 108 Figur 7 24 Configuration Scree s ssassiaainn annann aaa a RANA 109 Figure 7 25 Calibration Initiation Screen rrrrrrrrrririeee einen 109 Figure 7 26 Calibration Screen cca 110 Figure 7 27 AMCap Driver Welcome Screen cssssss sese sss cesses eenn nenen eee 111 Figure 7 28 AMCap Driver Choose Install Location rrrrrriiiiiiiii iii 111 Figure 7 29 AMCap Driver Installation Complete c sssssseeeeesccessssseeeeeeeeensnseeeeeeneoes 112 Figure 7 30 USB 3
108. the arm please ensure that it is VESA compliant and that the arm has a 75 mm or 100 mm interface pad If the mounting arm is not VESA compliant it cannot be used to support the AFL2 12A HM65 flat bezel panel PC Step 2 Once the mounting arm has been firmly attached to the surface lift the flat bezel panel PC onto the interface pad of the mounting arm Step 3 Align the retention screw holes on the mounting arm interface with those in the flat bezel panel PC Figure 4 11 100 mm Figure 4 11 Arm Mounting Retention Screw Holes Step 4 Secure the flat bezel panel PC to the interface pad by inserting four retention screws through the bottom of the mounting arm interface pad and into the flat bezel panel PC 4 8 4 Cabinet and Rack Installation The AFL2 12A HM65 flat bezel panel PC can be installed into a cabinet or rack The installation procedures are similar to the panel mounting installation To do this please follow the steps below Page 38 AFL2 12A HM65 Series Panel PC Ai NOTE When purchasing the cabinet rack installation bracket make sure it is compatible with both the AFL2 12A HM65 flat bezel panel PC and the rack cabinet into which the AFL2 12A HM65 is installed Step 1 Slide the rear chassis of the AFL2 12A HM65 flat bezel panel PC through the rack cabinet bracket until the aluminum frame is flush against the front of the bracket Figure 4 12 Rack Cabinet Bracket Figure 4 12
109. the basic system information Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced Chipset Boot Security Save amp Exit BIO Renon Set the Date Use Tab to BIOS Vendor American Megatrends switch between Data Core Version 4 6 4 0 0 15 elements Compliency l t Project Version SC99AR14 ROM Build Date and Time I Oey Aen a iWDD Vendor ICP Z Select Screen iWDD Version SC99ERl3 bin TY Select Item Enter Select System Date Monko ZA Change Opt System Time Krk Sos 210 Fl General Help F2 Previous Values Access Level Administrator F3 Optimized Defaults F4 Save amp Exit ESCE Version 2 10 1208 Copyright C 2010 American Megatrends Inc BIOS Menu 1 Main gt System Overview The System Overview lists a brief summary of different system components The fields in System Overview cannot be changed The items shown in the system overview include BIOS Vendor Installed BIOS vendor Core Version Current BIOS version Compliency Current BIOS compliant version Project Version The board version Build Date and Time Date the current BIOS version was made Access Level User access level The System Overview field also has two user configurable fields integration Corp AFL2 12A HM65 Series Panel PC gt System Date xx xx xx Use the System Date option to set the system date Manually enter the day month and year gt System Time xx xxX xx Use the Syst
110. the internal aluminum back cover See Section 5 4 2 above Locate the DDR3 SO DIMM on the motherboard Remove the DDR3 memory module by pulling both the spring retainer clips outward from the socket Integration Corp AFL2 12A HM65 Series Panel PC Step 7 Grasp the DDR3 memory module by the edges and carefully pull it out of the socket Step 8 Install the new DDR3 memory module by pushing it into the socket at an angle Figure 5 3 Step 9 Gently pull the spring retainer clips of the SO DIMM socket out and push the rear of the DDR memory module down Figure 5 3 Step 10 Release the spring retainer clips on the SO DIMM socket They clip into place and secure the DDR memory module in the socket Figure 5 3 DDR SO DIMM Module Installation Step 11 Replace the internal aluminum cover and secure it to the chassis using six 6 retention screws Step 12 Replace the back cover and secure it using nine 9 previously removed retention screws 5 5 2 WLAN Card Replacement Page 54 The AFL2 12A HM65 has one WLAN card slot To replace the WLAN card follow the instructions below Step 1 Follow all anti static procedures See Section 5 2 Step 2 Turn off the power See Section 5 3 Step 3 Remove the back cover See Section 5 4 1 vo io la L be v Sai En integration Corp AFL2 12A HM65 Series Panel PC Step 4 Remove the internal aluminum back cover See Sec
111. the number to print text 4 Figure D 24 Auto Recovery Environment for Windows Page 148 AFL2 12A HM65 Series Panel PC Step 5 The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition In this process the partition created for recovery files in Section D 2 2 is hidden and the auto recovery tool is saved in this partition 1P KEAR 61 nan SS Type NTFS 26936 MB 227 WB used from Local file Recowvery_PE2 gho 476938 HB Type 7 NTFS 20002 HB from Local drive 1 152627 MB iki Technology SS estoring remaining NTFS HFT fies Figure D 25 Building the Auto Recovery Partition Step 6 After completing the system configuration the following message prompts to confirm whether to create a factory default image Type Y to have the system create a factory default image automatically Type N within 6 seconds to skip this process The default option is YES It is suggested to choose YES for this option ct eat RIN DO WSieystem 2 cmd exe Backup Kecovery image automatically Are you suref LYNI m Figure D 26 Factory Default Image Confirmation Page 149 AFL2 12A HM65 Series Panel PC Type NTFS 100006 HB 1951 HB used No name from Local drive 80 130129 HB Local file D iei GHO Figure D 27 Image Creation Complete Step 8 After completing the system configuration press any key in the following window to restart the
112. ther antenna or transmitter IMPORTANT NOTE For products available in the USA Canada market only channel 1 11 can be operated Selection of other channels is not possible This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation TI ZER Li LEE integration AFL2 12A HM65 Series Panel PC Table of Contents LINRODUCLON a aan 1 1 1 AFL2 12A HM65 FLAT BEZEL PANEL PC OVERVIEW i 2 1 1 1 Model Variations iii reina 3 ERI EAT 3 RI ARROSTI 3 IZ EXTERNAL EELER EES 4 TR TTO TORO n e E E E E E 4 EEEE re EE 5 RARI Te INO 6 apse cect sos seaa taanssnae oasetatiaun cee sasseeqtucussven sogsote His aeecn seuss ea dscucawenee 6 LZ e E A I QUE EE 7 SLOT ET E ani ont S 124 lop F GNEL ING Side Panels iii nia 9 I SIN PRON ls VERVIEW ig deal ndr ieri ionici 10 1 4 SYSTEM SPECIFICATIONS AA 11 2 DETAILED SBC TXEISWMRILS Nk 13 GER KT 14 2 2 INTEL SANDY BRIDGE MOBILE PROCESSOR sse 16 SET 16 234 Memory SUPPO aria 16 2 3 1 1 Installed Memor 16 KS OTS CAPAC ROTA 16 2 4 EXTERNAL PERIPHERAL INTERFACE CONNECTORS sssseseeeessssssssssssseeeetrrrreresssssssss 16 E CTU INE OI ONCE IONS ina 16 EE 17 2 4 3 External USB siria 17 Zo EE 18 IO 18 EE EE 19 ZO AUDIO a E E E 19 2 6 1 Audio Codec Controller 19 WW
113. tion 5 4 2 Step 5 Locate the WLAN card Step 6 Disconnect the main and auxiliary antennas on the WLAN module Figure 5 4 L Figure 5 4 Removing the Antennas Step 7 Push the two spring clips in to release the WLAN card Si i HIIRIRIIRIDRDE SN 1143261010267 Figure 5 5 Releasing the WLAN Card Integration Corp AFL2 12A HM65 Series Panel PC Step 8 Grasp the WLAN card by the edges and carefully pull it out of the socket Figure 5 6 Figure 5 6 Removing the WLAN card Step 9 Install a new WLAN card by inserting the card into the slot at an angle Step 10 Push the WLAN card down until the spring retainer clips lock into place Step 11 Connect the main 1 and auxiliary 2 antennas The main antenna is indicated with a strip of black electrical tape See Figure 5 7 Ai NOTE To ensure the WLAN module functions correctly please make sure the WLAN antennas are attached in the proper configuration AFL2 12A HM65 Series Panel PC Black Tape MAIN 1 AUX 2 Figure 5 7 Attaching the Antennas Step 12 Replace the internal aluminum cover and secure it to the chassis using six 6 retention screws Step 13 Replace the back cover and secure it using nine 9 previously removed retention screws 5 6 Reinstalling the Covers A WARNING Failing to reinstall the covers may result in permanent damage to the system Please make sure all coverings are
114. tion screen in is shown See Figure 7 26 Page 109 ieee sD integration Corp AFL2 12A HM65 Series Panel PC Touch the red square Figure 7 26 Calibration Screen Step 10 Follow the instructions The user is asked touch the screen at five specified points after which the screen is calibrated 7 7 AMCap Driver Installation To install the AMCap driver please do the following Step 1 Access the driver list See Section 7 2 Step 2 Click AMCap and select the folder which corresponds to your operating system Step 3 Double click the setup file Step 4 The Welcome Screen in Figure 7 27 appears Step 5 Click Next to continue Page 110 S e Ki at En integrotio D op AFL2 12A HM65 Series Panel PC S AMCap Setup Welcome to the AMCap Setup Wizard This wizard will guide you through the installation of AMC op It is recommended that you close all other applications before starting Setup This will make it possible to update relevant system Files without having to reboot your computer Click Next to continue Cancel Figure 7 27 AMCap Driver Welcome Screen Step 6 Browse for an install location or use the one suggested Figure 7 28 Step 7 Click INSTALL to continue Bi AMCap Setup Choose Install Location Choose the Folder in which to install AMC op Setup will install 4MiCap in the Following folder To install in a different folder click B
115. tore the factory default image iei GHO created in Section D 2 5 2 Backup system Create a system backup image iei_user GHO which will be saved in the hidden partition 3 Restore your last backup Restore the last system backup image 4 Manual Enter the Symantec Ghost window to configure manually 5 Quit Exit the recovery tool and restart the system WARNING Please do not turn off the system power during the process of system recovery or backup Page 155 integration Corp AFL2 12A HM65 Series Panel PC A WARNING All data in the system will be deleted during the system recovery Please backup the system files before restoring the system either Factory Restore or Restore Backup D 5 1 Factory Restore To restore the factory default image please follow the steps below Step 1 Type lt 1 gt and press lt Enter gt in the main menu Step 2 The Symantec Ghost window appears and starts to restore the factory default A factory default image called iei GHO is created in the hidden Recovery partition ibi Company backup lool L01 Goporight Geir gt Somantec Corp 2000 Type CHTFS 100006 HE 1951 AB used Ho name from Local file D iei gho 130129 AB Type HTFS 100006 HE from Local drive 1 152627 HB Figure D 34 Restore Factory Default Step 3 The screen shown in Figure D 35 appears when completed Press any key to reboot the system Page 156
116. uble click on it Step 4 The setup files are extracted as shown in Figure 7 1 Intel Package Manager Intel Package Manager v i Intel Installation Framework Figure 7 1 Chipset Driver Screen Step 5 When the setup files are completely extracted the Welcome Screen in Figure 7 2 appears Step 6 Click Next to continue Integration Corp AFL2 12A HM65 Series Panel PC e Intel Chipset Device Software E x Intel Chipset Device Software intel Welcome to the Setup Program This setup program will install the Intel Chipset Device Software onto this computer Ik is strongly recommended that you exit all programs before continuing Cancel Intel Installation Framework Figure 7 2 Chipset Driver Welcome Screen Step 7 The license agreement in Figure 7 3 appears Step 8 Read the License Agreement Step 9 Click Yes to continue Intel Chipset Device Software ear Intel Chipset Device Software intel License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHY IS Distribution amp Single User IMPORTANT RESO BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Softwar
117. udio jack which is then connected to compliant audio devices The Realtek ALC888 is a 7 1 2 channel high definition audio codec with ten DAC channels It supports 7 1 sound playback and 2 channels of independent stereo sound output The audio connector is shown in Figure 2 7 Audio Connector Figure 2 7 Audio Jack 2 6 2 Stereo Speakers Two internal 1 5 W stereo speakers on the sides of the AFL2 12A HM65 are interfaced to the system 2 7 System Power 2 7 1 Power Mode The system can be run in the AT power mode or the ATX power mode Both these power modes are described below Integration Corp AFL2 12A HM65 Series Panel PC 2 7 1 1 ATX Power Mode Default With the ATX mode selected the AFL2 12A HM65 panel PC goes in a standby mode when it is turned off The panel PC can be easily turned on via network or a power switch in standby mode Remote power control is perfect for advertising applications since the broadcasting time for each panel PC can be set individually and controlled remotely Other possible application includes Security surveillance Point of Sale POS Advertising terminal 2 7 1 2 AT Power Mode With the AT mode selected the power is controlled by a central power unit rather than a power switch The AFL2 12A HM65 panel PC turns on automatically when the power is connected The AT mode benefits a production line to control multiple panel PCs from a central management center and oth
118. unction gt Disabled Wi Fi function disabled gt Enabled DEFAULT Wi Fi function enabled gt DMIC Function Enabled Use the DMIC Function option to enable or disable the DMIC function gt Disabled DMIC function disabled gt Enabled DEFAULT DMIC function enabled integration Corp AFL2 12A HM65 Series Panel PC gt BT Function Enabled Use the BT Function option to enable or disable the BT function gt Disabled BT function disabled gt Enabled DEFAULT BI function enabled gt Auto Dimming Support Enabled Use the Auto Dimming Support option to enable or disable auto dimming support gt Disabled Auto dimming support disabled gt Enabled DEFAULT Auto dimming support enabled gt Power Saving Function Disabled Use the Power Saving Function option to enable or disable the power saving function gt Disabled DEFAULT Power saving function disabled gt Enabled Power saving function enabled 6 5 3 Graphics Configuration Use the Graphics Configuration menu BIOS Menu 17 to configure the video device connected to the system AFL2 12A HM65 Series Panel PC Aptio Setup Utility Copyright C Chipset EE EE EES DVMT Pre Allocated DVMT Total Gfx Mem Boot Display Device Version 2 02 EE DEE 2010 American Megatrends Inc Rap R e Supports only one dual display mode in legacy environment DOS TAN DSL IR T E ierg TL Select Item EnterSelect 7 o Cie d
119. y key to boot from the recovery CD It will take a while to launch the recovery tool Please be patient When the recovery tool setup menu appears type lt 3 gt and press lt Enter gt Figure D 30 The Symantec Ghost window appears and starts configuring the system to build a recovery partition After completing the system configuration press any key to reboot the system Eject the recovery CD cy CARINDOWNS svystem32 wmd exe i Execute Ghost Z Manual Recovery environment For Windows 3 Manual Recovery environment For Linux 4 fiuto Recovery environment For Windows 5 Exit 6 Conmand Prompt Type the number to print text 3 Figure D 30 Manual Recovery Environment for Linux Step 5 Access the recovery tool main menu by modifying the menu lst To first access the recovery tool main menu the menu lst must be modified In Linux enter Administrator root When prompt appears type cd boot grub vi menu lst Page 153 fedora release 9 Sulphur ernel 2 6 25 14 fc9 i666 on an i686 tty2 localhost login root Password root localhost IR cd boot grub root localhost grubl vi menu lst Figure D 31 Access menu lst in Linux Text Mode Step 6 Modify the menu lst as shown below boot deu eda lef au lt A Limeout 18 insning hdb Alegqrubesplash xpm qz llddcnmcnu title Fedora 2 6 25 14 fc 1606 root hdt 3 kernel vumlinuz 4 6 25 14 fc9 1666 ro root UUID 18f lacd dr
120. zel Panel PC Overview Figure 1 1 AFL2 12A HM65 Flat Bezel Panel PC The AFL2 12A HM65 is an Intel Sandy Bridge Mobile CPU powered flat bezel panel PC with a rich variety of functions and peripherals The AFL2 12A HM65 is designed for easy and simplified integration into kiosk and point of sales POS applications An Intel Sandy Bridge Mobile CPU coupled with an Intel HM65 input output controller hub ensures optimal memory graphics and peripheral I O support The system comes with 1 0 GB of preinstalled DDR3 SDRAM ensuring smooth data throughputs with reduced bottlenecks and fast system access Three serial ports two external USB 2 0 ports and two external USB 3 0 ports ensure simplified connectivity to a variety of external peripheral devices Wi Fi capabilities and the RJ 45 Ethernet connector provide the system with smooth connection to an external LAN An optional MSR card reader can equip the system for scanning credit cards identification cards loyalty cards gift cards and more AFL2 12A HM65 Series Panel PC WW ame Su E l Iintegrationi 1 1 1 Model Variations The model variations of the AFL2 12A HM65 Series are listed below Model No Optional Features AFL2 12A HM65 PC EM R11 EM card reader AFL2 12A HM65 PC MF R11 MIFARE card reader AFL2 12A HM65 PC R11 N A AFL2 12A HM65 R EM R11 5 Wire Resistive EM card reader AFL2 12A HM65 R MF R11 5 Wire Resistive MIFARE card reader AFL2 12A HM65 R R1

Download Pdf Manuals

Related Search

Related Contents

InLine 74010Z  Bedienungsanleitung Operating Instructions    Ermittlung des Normungsbedarfs zur Festlegung von  Info sidé 116 - octobre 2015  Design and Prototyping of a Cognitive Model  Data Sheet  マニュアル（2.7MB）  5350036126 LYNX KATLAMA KAPAK  Sony Xperia J ST26i 4GB 4G White  

Copyright © All rights reserved. Failed to retrieve file