ISM0084 - GM International srl
Contents
1. fE DC 3 Wire Downecale 20 00 nv a Upscale 20 00 miy The screenshot above shows a portion of the Input Column in the Configuration Tab Note 1 A field is disabled if the unit does not accept such parameter or if at that moment it is not meaningful for the configuration For example as shown in figure above it is senseless to choose the number of wires Lead when a voltage E dc sensor is selected The field is re enabled when a Thermoresistance input is selected Note 2 Certain Text Fields must be filled in according to numeric ranges that are related to that field For example Upscale value must be within the range of the selected Input sensor If the value is out of range the software will alert the user and adjust the value to the maximum or minimum value depending on which of the two was violated Note 3 Certain Text Fields must be filled in according to cross relationships with other Text fields values For example Low Burnout Limit value must be lower than Low Working Limit If such a condition is violated the software will prevent the insertion of that parameter ISM0084 2 Installation and use of the SWC1090 calibration software Page 6 of 12 VY Installation and use of the YEDMNGLDGY FOR SAFETY SWC1090 Configuration software 1 3 1 3 Knowing more about the unit If the related preference is set in the Settings tab a link to the unit s details page on G M Int2. to internet is required software by clicking To update via our website please visit i agree or by downloading installing or using the SWC1090 software you agree http www gmintstl com to the terms of this AGREEMENT and you consent to jurisdiction of the european union for any dispute You acknowledge that GMI offers the S WC1090 software without warranties and that your remedies are limited If you do not agree to this AGREEMENT click exit and do not install or use the S W C1090 software G M International s r l gt LICENSE GRANT Via San Fiorano 70 GMI grants you a personal limited non exclusive non sublicensable 20058 Villasanta Ml non transferable license to use ITALY the SWC1090 software for personal and internal business purposes provided any copy must contain all of the original proprietary notices This license does not entitle you to receive from S WC1090 software hard copy documentation support telephone http gmintsrl com assistance or enhancements or updates to the SWC1090 software info gmintsr com 3 RESTRICTIONS You may not li modify or create any derivative works of the S WC1090 software or documentation including customization translation or localization aside from any rights you may have to modify those portions of the source code released under a separate source code license ii decompile disassemble reverse engineer or otherwise attempt to deri
3. Installation and use of the SWC1090 calibration software Page 5 of 12 VY Installation and use of the YEDMNOLDGY FOR SAFETY SWC1090 Configuration software 1 3 1 1 Loading configuration parameters The most important actions that can be taken in the Configuration Tab are accessible through the 7 buttons on the top right see figure below Bl 10 x I 2 3 5 6 F 8 6 al a a 2 Channel 1 Load from COM port reads parameters from the default COM port Save to COM port writes current configuration to the default COM port Load from File loads a previously saved configuration from file to screen Save to File saves a copy of the configuration to a file Load Factory Defaults loads factory default configurations press Button 2 to save Print Report Sheet prints a summary of the current configuration see Section 1 4 for details Reset Form brings all form fields to blank Help opens this manual O N oe Note These functions are also accessible via keyboard shortcuts using the related Function keys For example F1 will activate the Load from COM port function F2 the Save to COM port and so on 1 3 1 2 Working with parameters Once a configuration is loaded to screen the parameters can be displayed in two ways 1 List boxes user chooses between a predetermined set of values 2 Text fields user specifies a numerical value INFOT Channel 1 Sensor
4. R 8 toT ADOUAT E E E ET 8 14 WRIA TOTS NS OLS eseririk aanas r a ESE ENE EN va ENA dated ERE aa SA e E aSa 9 to Logging CAD AIMS S tata unietnecnccoxensnetalacsniiisenutan e a E E E E a E 9 2 Installation and quick start aasnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn ennnen nenn nnnn nnmnnn ennnen nnna 10 2 1 Installing the SWC1090 ec ccccccceceeeeeeeeeeeeeeseeeeeeeaeeeeeseeeeeeseeseeeeseaeeeeeeaseeesseeeeeseeeeeeseeseeeesaeeeeesaeeeeesaaes 10 2 2 Connecting cables powering the unit ce cecccceceeeeeeeeeeeeeaeeeeeeseeeeeeeeeeeeesaaseeeesaeeeesaeeeeeseaeesesaeeeeesaees 10 293 COMMING LON SENOS cece actrees tec E AE cd dt seneens EE Renee i E E E E E E 10 ZA Tesing SCH Al COMMCCOMN serrr rA E AE R E E na AE REAR EAE arai 10 3 Troubleshooting and SUPPOTT sgarsrasssvatsiossuneatasanasorosevabsvebwavausveussabovexeyaloveuivalsieuasabsvesamuuercensiynecontuoserauartessakovecs 11 31 SarnalconnectoMss i AE E EE E NEEE E EEE E ERE 11 3 2 Updating to a newer version cccccccseeccceeeeceeeeceeeeeseeeeseeeeseeeeeseeeeeaaeeessaeeeseaeeeseeeseueeesausessaneeesaaeeesneessees 11 4 Software revisions and updating instructions ssssssssnusnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nenna n mnene 12 ISM0084 2 Installation and use of the SWC1090 calibration software Page 2 of 12 CV Installation and use of the YEDMNGLOGY FOR SAFETY SWC1090 Configuration software 1
5. The SWC1090 Configuration Software GM International SWC1090 Configurator 1 3 0 2 151 x Configuration Values Settings About cogo cy he i T INPUT OUTPUT Channel 1 Channel 1 z he 4 m z m Channel 2 z hd m z m UL Tm I Tt Model Source Date 1120722008 Status Ready D1072D Temperature Converter 18 50 43 1 1 Introduction The SWC1090 is designed to provide a PC user interface to configure D1000 and E1000 series isolators that accept user settings a list of software configurable models can be found at Section 1 2 1 The SWC1090 allows the user to a Read and write configuration parameters to the units via COM port Store and restore data to and from local hard drive for backup or archive Load factory default configurations Monitor Input values via COM port Print a report sheet containing configuration parameters and additional information Ooo O The SWC1090 is freely distributed at http www gmintsrl com and can be found in the CD ROM that comes together with the PPC1092 Adapter 1 2 Requirements The SWC1090 is to be installed on a machine with the following minimum requirements O Pentium class Processor 200Mhz 800x600 pixels screen resolution 64MB RAM 1 available Serial RS 232 Port or USB port if Serial to USB adapter is used Microsoft Wi
6. VY Installation and use of the YEDMNGLOGY FOR SAFETY SWC1090 Configuration software SWC1090 configuration software for G M International Isolators series D1000 and E1000 Installation and use manual ISM0084 2 Installation and use of the SWC1090 calibration software Page 1 of 12 CV Installation and use of the YEDMNOLDGY FOR SAFETY SWC1090 Configuration software Index of Contents 1 The SWC1090 Configuration Softwar e cccccssseeessseeeeeeeseeeeeesneeeseeseeseeesseeeeeneeeseeeeeenesseeseasneesensnseeseneneessonsnees 3 EE REMC OCU IO eee E cats hot ou aaeinabeestcte gauetwatsedibr ending sainenalleasei E E E E E E NE 3 ka PRO CUNO NUNC aoran E EEE san anes E E ET 3 1 2 1 CAE U E N E E E E E 4 t3 User AU A Ca cate pt ce ca sec in ah cv edi pcm at to dn lee dee ante ade anc dais dncpee aden ae 5 1 3 1 Configuration TAD acts sssto cc eacnictropeg iesaaakace aanaisiiegienaedceaaadtiddncsSntenansslsapenants sdemasddeiiaansssesenesinedaeans ieee 5 1 3 1 1 Loading Configuration parameters ccccceecccecseeeeceeeeeeeseeeeeesaeeeeeeaeeeeeseeeeesaaeeessaneeesaaesees 6 1 3 1 2 Working with parameters seicciinsecicdusdenwelan nouandibjavaclunicnacandduswedunsipsiniansennedsnbencetianniuenibadaverdsaaets 6 1 3 1 3 Knowing more about the unit ccc cccccssecesesecesseeeceeeeeeeseeeeaseeseaeessaseesaeeeseaeseseueseneeeens T toa VANS aD a a p a e e ae EE E EE T Boo 1 2 111 9 0 T aD a E E E EE EE A A E AE E EAE eT ne
7. ation and use of the SWC1090 calibration software Page 9 of 12 CV Installation and use of the YEDMNOLDGY FOR SAFETY SWC1090 Configuration software 2 Installation and quick start After having checked the requirements at Section 1 2 it is possible to proceed with the installation 2 1 Installing the SWC1090 Be sure to retrieve the latest installer executable from hitp www gmintsrl com In case a previous version of the SWC1090 was installed on the system it is preferable to uninstall it before continuing Launch the installer and follow the instructions An icon will appear on your desktop at the end of the process 2 2 Connecting cables powering the unit The unit is connected to the PC using a PPC1092 adapter see Section 1 2 at page 3 for details Supply the unit as told in the product datasheet 2 3 Connection settings The first time the software is activated a welcome dialog box will appear Click OK and the Configuration Tab will be presented see Section 1 3 1 for details The SWC1090 is configured by default to use Serial Port COM1 to change this setting proceed to the Settings Tab It is possible to choose from an available port in the Manual selection list or to press the COM port discover button that will search for a valid unit among all available serial ports on the PC In this case remember that the unit must be powered up and properly connected 2 4 Testing serial
8. bout Details of their contents are described in the following sections 1 3 1 Configuration Tab E4 G M International SWC1090 Configurator 1 3 0 B 1o x Configuration Values Settings About D1072D S e al a 7 INPUT OUTPUT Channel 1 Channel 1 Sensor JE DC Output fisv gt zj z 3 wire Downscale oog mY Burnout None 7 Upscale 20 00 mY Function cha Channel 2 z z Automatic Output 4 20 m il 2 50 v v v fo 00 Burnout None 7 Function ch A x Alam TB Channel 2 Yt Yl Input Pot x Output Limits Ti rr 4wire E B a rr rr Downscale joo x HZ E Upscale f100 0 lr rr Automatic TAG lt lt 25 0 1 Tai 18 49 40 SWC1090 1 3 0 started po 2 TAG2 18 52 52 Read D1072D configuration from COM4 Aquire Zero E a Model D10720 Source COM4 Date 11 07 2008 Status Ready D1072D Temperature Converter Modified 18 54 27 The Configuration Tab is the main interface that allows to create and modify configurations Parameters can be loaded to screen in three ways a From COM port a From File QO From Factory Default The main area is divided into columns representing a Input Channels 1 and 2 Q Output Channels 1 and 2 tags general information a Alarms A and B Channel 1 Q Alarms A and B Channel 2 ISM0084 2
9. connection After choosing the correct COM port we are ready to configure our first units Open the Configuration Tab and press the Load from COM Port F1 button if the parameters are correctly loaded to screen it means that everything is correct If an error occurs refer to Section 3 1 at page 11 for help ISM0084 2 Installation and use of the SWC1090 calibration software Page 10 of 12 VY Installation and use of the YEDMMGLDGY FOR SAFETY SWC1090 Configuration software 3 Troubleshooting and support 3 1 Serial connection x A Default COM Port COM2 defined in Settings is not available at the moment Please Verify that cable CABFO04 is correctly plugged in the module 6 pin jack module is correctly supplied serial cable is CABFOO10 or similar COM port settings are correct USB ferial converter if present is functioning This message appears whenever the user attempts to access the serial port which was previously defined in the Settings tab and the operation is not successful Given that all cables are properly connected the remaining possible reasons are listed below Q Unit is not configurable via SWC1090 software Verify that the unit is among the list at Section 1 2 1 page 4 Q Serial cable used to connect the PC to the PPC1092 is not a Null Modem RS 232 cable please see Note 1 in Section 1 2 page 3 for specifics Q Unit is not correctly supplied or not supplied at all see units
10. datasheet for instructions QO PC Serial port is not correct Try the COM port discover function in the Settings tab in case this does not work look for COM port properties in Control Panel gt System gt Hardware gt Peripherals If a USB to Serial adapter is being used please also check that drivers are correctly installed and operational G M International PPC1092 is shipped with a USB to Serial Adapter figure below Drivers for this model can be found on the CD Rom that is given with the adapter or on the internet at http Awww gminternationalsrl com 3 2 Updating to a newer version In order for the new version to be downloaded from the internet a valid connection is required together with write permissions in the SWC1090 main installation directory typically C Program Files SWC1090 Firewall or antivirus programs may block the downloading of the file please be sure to add gminternationalsrl com domain to the list of trusted sites The automatic update check can be disabled from the Settings Tab If for any reason the internal update function does not work properly it is always possible to proceed to our website nttp www gmintsrl com to download the most updated version of the SWC1090 ISM0084 2 Installation and use of the SWC1090 calibration software Page 11 of 12 CV Installation and use of the venue Poke BANIN SWC1091 Calibration software 4 Software revisions and updating in
11. e the unit for its current Input value at a user selectable refresh rate Options The chart will graphically represent the status of the input with a 3 minutes window The Input axis Y is resized depending on the type of input that is configured at that time During the acquiring session it is kept memory of the Maximum Minimum and Average values Session These values are canceled every time a new session is initiated If the inserted unit is a dual channel model it is possible to choose what channel to monitor Note 1 it is possible to monitor only one channel at a time Note 2 changing Tab while in a monitoring session will cause the stopping of the acquiring session ISM0084 2 Installation and use of the SWC1090 calibration software Page 7 of 12 Installation and use of the INTERNATIONAL TECHNOLOGY FOR SAFETY SWC1090 Configuration software 1 3 3 Settings Tab Preferences security and network settings can be adjusted through the Settings tab as shown below Ea G M International SWC1090 Configurator 1 3 0 Bj 10 xj Configuration Values Settings About M COM PORT SETTINGS SECURITY The COM Port is the physical interface between your PC Activate Password Restriction and the PPC 1092 converter to which the Isolator has to be connected figure below an be set to avoid unauthorized change Administration Password The COM port discover button scans available ports to find a
12. ernational website will be displayed in the lower part of the screen By clicking on the link an internal browser window will open and show unit characteristics details and downloadable material such as datasheets instruction manuals application notes and certifications Note An internet connection is needed for accessing this feature In the lower right part of the Tab major actions taken by the user in the SWC1090 are logged as text lines This data is saved at the end of each working session see Section Logging 1 5 to Know more about this feature 1 3 2 Values Tab It is possible to read the value of the unit s input channel via serial commands using the SWC1090 To do so please open the Values Tab If the unit is ready and the connection settings are correct the user will be presented with the following screen Ea GM International SWC1090 Configurator 1 3 0 g B 101 x Configuration Values Settings About CHANNEL 1 INPUT Information Model D1072D Sensor EDC mV Status Idle Options Refresh rate ms 200 30 i H i i i i START 0O 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 Time Modified 19 01 03 D1072D Temperature Converter The fields Model and Sensor are filled in by the software that recognizes the unit that is connected at that moment By pressing the START Button the SWC1090 will interrogat
13. ndows operative system Dood wo Furthermore as shown in figure below the following items are required a PPC1092 adapter QO CABFO10 Null Modem Serial Cable see Note 1 below for details QO CABFO04 6 pin cable RJ 12 jack ISM0084 2 Installation and use of the SWC1090 calibration software Page 3 of 12 CV Installation and use of the YEDMNOLDGY FOR SAFETY SWC1090 Configuration software The image below clarifies the situation Note 1 CABF010 serial cable is a NULL Model type of cable and not a straight cable the wiring diagram is the following DB 9 female ajea Ad 1 2 1 Configurable units Following is a list of units that can be configured via software a Frequency Input D1060S Analog Temperature Input D1070S D1072S D1072D D1072X D1072Y D1073S Analog Input D1050S D1052S D1052D D1052X D1052Y D1053S D1054S Load cell Input D1064S Eurocard E1058S E1058D E1059S E1059D E1078S E1078D E1079S E1079D Doo vo Note If your unit has a 4 pin jack connector on the front it cannot be configured via software even if it is listed among the above A PPC1090 Pocket Portable Configurator is needed instead ISM0084 2 Installation and use of the SWC1090 calibration software Page 4 of 12 CY Installation and use of the Yansenicaey POR SAFETY SWC1090 Configuration software 1 3 User Interface The SWC1090 user interface is organized into four different Tabs Q Configuration O Values a Settings O A
14. o select one of them Q Security Restrict the access to the software by activating this option Various various user preferences Q Additional Information These two fields are used when saving to file or when printing a report sheet By checking the Remember next time option this information will be memorized in the SWC1090 after closing the application E 1 3 4 About Tab The About tab contains the End User License Agreement G M International contact details and the button for checking if an update is available See Section 3 2 for details on the updating process 4G International SWC1090 Configurator 1 3 0 Bj 5 x Configuration Values Settings About End User License Agreement SWC1090 Configuration Software is freely distributed by G M International s r l Villasanta Italy INTERNATIONAL and can be found at the following internet address http www gmintsrl com TECHNOLOGY FOR SAFETY SWC1090 software END USER LICENSE AGREEMENT m Software update THIS IS A LEGALLY BINDING AGREEMENT BETWEEN YOU EITHER AN Instaled vandion 4 2 0 ae OR A SINGLE ENTITY AND GM Intemational si Server version 1 THIS SWC1090 Configuration Software S WC1090 software End Search for updates User License AGREEMENT the AGREEMENT governs use of the SWC1090 software and any related software services provided by GMI or its partners in connection with the SWC1090 Note A connection
15. structions Updating to the latest version is always highly recommended Features added to new products may be configured only via the latest SWC1090 Backward compatibility with older models is guaranteed The SWC1090 is able to detect if a more recent version is available for download and starting from version 1 2 0 to start the installation by itself thus making it easier for the user This feature can be either initiated automatically at startup or by the user pressing the button in the About Tab see figure below In both cases a connection to the internet is required Software update For more details on the installation procedure see Section 2 1 at page 10 and Installed version 1 2 0 Section 3 2 for troubleshooting Server version Search for updates Ma eor Ulead etree Remember to visit G M International website at hitp Awww gmintsrl com to find out o update via our website please visit http www gmintsrl com the latest news and updates on our products and software Document subject to change without notice please refer to web site for latest update G M International s r l Via San Fiorano 70 20058 Villasanta MI Italy Phone 39 039 2325 038 Fax 39 039 2325 107 e mail info gmintsrl com Web www gmintsrl com ISM0084 2 Installation and use of the SWC1091 calibration software Page 12 of 12
16. valid GM module the Manual selection option gives the possibility to choose any port among available ones rds are Case Sensitive WORD is different from password old New Modify Please remember that the module VARIOUS must be corectly connected and Warn when writing unmodified configuration supplied Please refer to datasheet Cars 3 or instruction manual for further Automatically close confirm dialog after reading configuration J details Automatically close confirm dialog after writing configuration J View Values screen at opening Default COM port COM4 Show link to online product information when connected to the internet Automatically check for updates at startup COM port discover Start Manual selection Change m ADDITIONAL INFORMATION Configuration done by Configuration done fen remember next time J Save I Warn if information is found empty before saving Help Status Ready D1072D Temperature Converter Modified 19 01 22 a COM port settings define which RS 232 serial port is to be used by the SWC1090 to communicate with the unit The COM port discover option may be initiated at any time by the user in order to search for a valid unit that was previously connected to the PC refer to Section 2 for connection details The Manual selection option shows COM ports available on the PC and allows the user t
17. ve the source code of the S WC1090 software or in any way ascertain decipher or obtain the communications protocols for accessing the SWC1090 software or the underlying ideas or algorithms of the SWC1090 software Status Ready D1072D Temperature Converter Modified 19 01 41 ISM0084 2 Installation and use of the SWC1090 calibration software Page 8 of 12 VY Installation and use of the YEDMNGLDGY FOR SAFETY SWC1090 Configuration software 1 4 Printing report sheets Configuration sets can be printed to paper using the Print Report Sheet button A Print dialog will appear offering the choice between available printers Fields Configured by and Configured for can be edited in the Settings Tab see 1 3 3 at page 8 1 5 Logging capabilities The SWC1090 has a built in logging capability that keeps a backup of the following Q Configurations that are read and written from and to COM port saved to file config log O System actions taken by the user in the SWC1090 saved to file system log Both files are located in the log directory inside the main program location usually C Programs and Files SWC1090 and are written in a human readable ASCII format they may be therefore consulted using any text editor e g Notepad Note Data is appended at the end of the files each time the SWC1090 is closed A backup copy is made when the file s size exceeds 5 MB ISM0084 2 Install
Download Pdf Manuals
Related Search