Home

2nAxxxxyy Ez User Manual - Diamond Point International

1. N USB Ethernet VGA 7 i Battery MEN Mikro Elektronik GmbH 32 20F021P00 E4 2015 01 13 Functional Description 2 10 Graphics The graphics subsystem is part of the Intel QM67 Platform Controller Hub and supports VGA as well as different digital display interfaces HDMI DisplayPort and SDVO 2 10 1 VGA Front Connection You can connect a VGA monitor directly at the F21P s front panel The pinout of the 15 pin HD Sub connector is standard VGA Connector types 15 pin HD Sub receptacle according to DIN41652 MIL C 24308 with thread bolt UNC 4 40 Mating connector 15 pin HD Sub plug according to DIN41652 MIL C 24308 available for ribbon cable insulation piercing connection hand soldering connection or crimp con nection Table 2 Pin assignment of 15 pin HD Sub VGA receptacle connector 15 SCL 10 GND 5 GND 14 VSYNC 9 4 13 HSYNC 8 GND 3 B 12 SDA 7 GND 2 G 11 6 GND 1 R Table 3 Signal mnemonics of 15 pin HD Sub VGA connector Signal Direction Function GND Ground HSYNC out Horizontal synchronization R G B out Analog monitor interface red green blue SCL out Monitor I C interface SDA in out VSYNC out Vertical synchronization 2 10 2 VGA Rear Connection For conduction cooled versions of the F21P there is the possibilit
2. 1 1 Map of the Board Figure 1 Map of the board front view F22P Standard O VIS n Oo N w Oo n MEN Mikro Elektronik GmbH 20 20F021P00 E4 2015 01 13 Getting Started mSATA disk microSD card bottom 2 o USB Ethernet i VGA le NEN ERR Ee I Battery MEN Mikro Elektronik GmbH 21 20F021P00 E4 2015 01 13 Getting Started 1 2 Configuring the Hardware You should check your hardware requirements before installing the board in a system since most modifications are difficult or even impossible to do when the board is mounted in a system The following check list gives an overview on what you might want to configure M microSD The board is shipped without a microSD card You should check your needs and install a suitable microSD card Refer to Chapter 2 9 Mass Storage on page 29 for more information on installation of the card M mSATA disk The board is shipped without an mSATA disk You should check your needs and install a suitable disk Refer to Chapter 2 9 8 mSATA Disk on page 31 for more information on installation of the card MI Expansion by a side card The board offers the option of adding one side card Side cards come in standard 3U format and can be attached directly to F21P at the heat sink side Every side card has dedicated
3. F21P data sheet with up to date information and documentation 5 1 1 CPU Intel Embedded Processors SATA Serial ATA International Organization SATA IO USB USB Implementers Forum Inc 5 1 4 Ethernet ANSI IEEE 802 3 1996 Information Technology Telecommunications and Information Exchange between Systems Local and Metropolitan Area Net works Specific Requirements Part 3 Carrier Sense Multiple Access with Col lision Detection CSMA CD Access Method and Physical Layer Specifications 1996 IEEE E ANSI IEEE 802 3 1996 Charles Spurgeon s Ethernet Web Site Extensive information about Ethernet IEEE 802 3 local area network LAN technology InterOperability Laboratory University of New Hampshire General Ethernet technology MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Appendix 5 1 5 HD Audio Intel High Definition Audio 5 1 6 PCI Express lef PCI Special Interest Group 5 1 7 CompactPCl 7 CompactPCI PluslO Specification PICMG 2 0 R3 0 bz 1999 PCI Industrial Computers Manufacturers Group PICMG AE PCI Local Bus Specification Revision 2 2 helf 1995 PCI Special Interest Group P O Box 14070 Portland OR 97214 USA 5 1 8 CompactPCI PluslO D CompactPCI PluslO Specification PICMG 2 30 R1 0 b 2 1999 PCI Industrial Computers Manufac
4. Temperature measurement One user LED Reset button MEN Mikro Elektronik GmbH oJ 20F021P00 E4 2015 01 13 Technical Data PCI Express Three x1 links to connect local 1000Base T Ethernet controllers Data rate 250 MB s in each direction 2 5 Gbit s per lane Four x1 links via rear I O Data rate up to 500 MB s in each direction 5 Gbit s per lane Three x1 links for extension through side card connector Data rate up to 500 MB s in each direction 5 Gbit s per lane CompactPCI Bus Connection via PCI Express link from processor using PCI Express to PCI Bridge Compliance with CompactPCI Core Specification PICMG 2 0 R3 0 System slot 32 bit 33 MHz CompactPCI bus e V I O 3 3V 5V tolerant Busless Operation Board can be supplied with 5V only all other voltages are generated on the board Backplane connectors used only for power supply Electrical Specifications e Supply voltage power consumption board versions with 17 2715QE processor 5V 3 5 9 6 A typ 14 4 A max 3 3V 3 5 1 8 A 3 Gb Ethernet 1 4 A 2 Gb Ethernet 1 A 1 Gb Ethernet 12V 10 10 approx 10 mA If the board is supplied with 5V only typically without a bus connection the 3 3V are generated on the board and fed to the backplane 3A max No external 3 3 V voltage may be applied in that case Mechanical Specifications Dimensions conforming to CompactPCI specification for 3
5. GHz 1 1 17 W 1 5 MB no MEN Mikro Elektronik GmbH 27 20F021P00 E4 2015 01 13 Functional Description 2 7 1 Thermal Considerations A suitable heat sink is provided to meet thermal requirements For special requirements a larger heat sink is also available on request no heat sink at all warranty on functionality and reliability of the F21P may cease If you have any questions or problems regarding thermal behavior contact MEN Note that if you use any other heat sink than that supplied by MEN or E Contact MEN sales for more information on this topic 2 8 Memory The standard board versions provide a memory configuration suitable for many applications However memory on the F21P can also be configured for your needs d For standard memory sizes and ordering options see MEN s website 2 8 1 DRAM System Memory The board provides up to 16 GB onboard soldered DDR3 double data rate SDRAM The memory bus is 2x72 bits wide dual channel and operates with up to 1066 MHz 2 8 2 Boot Flash The F21P has a 64 Mbit SPI Serial Flash implemented as onboard Flash for BIOS data MEN Mikro Elektronik GmbH 28 20F021P00 E4 2015 01 13 Functional Description 2 9 Mass Storage The F21P offers six SATA lines on the J2 rear I O connector and the side card connector In addition the board offers the possibility to connect an mSATA disk and a microSD card on a small adap
6. Mouse KVM Viewer VNC compatible IDE Redirect Serial over LAN MEN Mikro Elektronik GmbH 7 20F021P00 E4 2015 01 13 Technical Data Software Support Note that 64 bit hardware technology can be used in an optimal way with 64 bit operating system support Windows Linux VxWorks on request QNX on request Intel Virtualization Technology allows a platform to run multiple operating systems and applications in independent partitions one computer system can function as multiple virtual systems D For more information on supported operating system versions and W drivers see Downloads MEN Mikro Elektronik GmbH 8 20F021P00 E4 2015 01 13 Configuration Options Configuration Options CPU e Intel Core i7 2715QE 2 1 GHz 6 MB Cache 45 W e Intel Core i7 2655LE 2 2 GHz 4 MB Cache 25 W Intel Core i7 2610UE 1 5 GHz 4 MB Cache 17 W Intel Core i5 2515E 2 5 GHz 3 MB Cache 35 W e Intel Core i3 2340UE 1 3 GHz 3 MB Cache 17 W no AMT Intel Core i3 2310E 2 1 GHz 3 MB Cache 35 W no AMT Intel Celeron B810E 1 6 GHz 2 MB Cache 35 W no AMT Intel Celeron 847E 1 1 GHz 2 MB Cache 17 W no AMT Intel Celeron 827E 1 4 GHz 1 5 MB Cache 17 W no AMT Memory System RAM Upto 16 GB microSD card 0 MB up to maximum available mSATA disk 0 MB up to maximum available Graphics One DVI D connector at front via
7. Time Description Change the internal clock Options hh Hours Valid range from 0 to 23 mm Minutes Valid range from 0 to 59 SS Seconds Valid range from 0 to 59 System Date Description Change the date Options mm Month Valid range from 1 to 12 dd Day Valid range from 1 to 31 yyyy Year Valid range from 2000 to 2099 Full Configuration Mode Description The F21P BIOS has two configuration modes One mode shows only a selection of the most important items and hides items where normally no changes in the settings are required Options Yes Enable full configuration mode No Disable full configuration mode MEN Mikro Elektronik GmbH 58 20F021P00 E4 2015 01 13 BIOS 3 2 Advanced InsydeH20 Setup Utility Rev 3 5 F1 Help 1 Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt Select Menu Enter Select gt F10 Save and Exit Submenu MENMISGEEENOMEGNUHO se eee 59 20F021P00 E4 2015 01 13 BIOS Boot Configuration Sub menu SATA Port on Sidecard Pore B SATA Port on Sidecard Description Selects the SATA port on the sidecard Options Port A Port B Peripheral Configuration Sub menu HD Audio Disabled LAN 1 Enabled LAN 2 Enabled LAN 3 Enabled HD Audio Description Enable or disable the HD Audio controller Options Auto The controller is enabled if a codec is found Disabled The controller is disabled even when there is an audio codec Enabled The controller is enabled
8. at front panel Two digital display interface ports available via side card connector DisplayPort HDMI and SDVO SDVO only on one interface One additional DVI connector at front panel optional via side card Simultaneous connection of two monitors MEN Mikro Elektronik GmbH 4 20F021P00 E4 2015 01 13 Technical Data I O USB Two USB 2 0 ports via Series A connectors at front panel Four USB 2 0 ports via side card connector Four USB 2 0 ports via rear I O One USB for connection of microSD UHCI implementation Data rates up to 480 Mbit s Ethernet Two 10 100 1000Base T Ethernet channels at the front RJ45 connectors at front panel Ethernet controllers are connected by two x1 PCIe links Onboard LEDs to signal activity status and connection speed One 10 100 1000Base T Ethernet channel via rear I O Ethernet controller is connected by one x1 PCIe link High Definition HD audio Accessible via side card connector Front Connections Standard VGA Two USB 2 0 Series A Two Ethernet RJ45 Rear I O PICMG 2 30 Four SATA Four USB One Gigabit Ethernet second rear interface instead of one front interface as an assembly option Four PCI Express x1 links Compatible with PICMG 2 30 CompactPCI PlusIO 1PCI33 4PCIES 2SATA3 2S ATA6 4USB2 1 2 ETH1G Miscellaneous Board controller Real time clock buffered by a GoldCap or alternatively a battery 5 years life cycle Watchdog timer
9. changed Any attempt to change this address may create node or bus The unique MAC address is set at the factory and should not be contention and thereby render the board inoperable The naming of the interfaces may differ depending on the operating system The MAC addresses on F21P are LANI upper front interface 0x 00 CO 3A AE 80 00 Ox 00 CO 3A AE FF FF e LAN2 lower front interface 0x 00 CO 3A AF 00 00 Ox 00 CO 3A AF 7F FF LANG rear I O 0x 00 CO 3A AF 80 00 Ox 00 CO 3A AF FF FF where 00 CO 3A is the MEN vendor code The last six digits describe the range from which the addresses for the board are taken The serial number is added to the first number in the range Serial number 0042 0x2A Ox 80 00 Ox 00 2A Ox 80 2A Also see Chapter 5 2 Finding out the Product s Article Number Revision and Serial Number on page 81 2 12 1 Front Panel Connection Two standard RJ45 connectors are available at the front panel There are two status LEDs for each channel at the front panel The pin assignment corresponds to the Ethernet specification IEEE802 3 Table 6 Signal mnemonics of Ethernet 10 100 1000Base T connectors Signal Direction Function BI_Dx in out Differential pairs of data lines for 1000Base T RX in Differential pair of receive data lines for 10 100Base T TX out Differential pair of transmit data lines for 10 100Base T MEN Mikro Elektro
10. functions e g legacy COM interfaces SATA hard disk or DVI front connectors Refer to Chapter 2 14 Side Card Interface on page 40 for further information on side cards The MEN sales staff will be glad to help you find the right extension b 2 and front panel solution See also MEN s website for ordering information and standard products MEN Mikro Elektronik GmbH 22 20F021P00 E4 2015 01 13 Getting Started 1 3 Integrating the Board into a System You can use the following check list when installing the F21P in a system for the first time and with minimum configuration M Power down the system Mi Remove all boards from the CompactPCI system M Insert the F21P into the system slot of your CompactPCI system making sure that the CompactPCI connectors are properly aligned Note The system slot of every CompactPCI system is marked by a A triangle on the backplane and or at the front panel It also has red guide rails Connect a USB keyboard and mouse to the USB connectors at the front panel Connect a CRT or flat panel display to the VGA connector at the front panel Power up the system KI You can start up the BIOS setup menu by hitting the F2 key MI Now you can make configurations in BIOS For more Information on the BIOS see Chapter 3 BIOS on page 56 M Observe the installation instructions for the respective software MEN Mikro Elektronik GmbH 23 20F021P00 E4 2015
11. independent of the presence of a codec LAN 1 LAN 2 LAN 3 Description Enables or disables the LAN interfaces Options Enabled Disabled IDE Configuration Sub menu IDE Mode IDE Controller HDC Configure as gt Serial gt Serial gt Serial gt Serial gt Serial gt Serial IDE Controller Port Port Port Port Port Port O1 2 CO n5 P2 C5 Not Not Not Not Not Not Enabled LIUDIE Installed Installed Installed Installed Installed Installed Description Enables or disables the IDE controllers Options HDC Configure as Enabled Disabled Description Set hard disk controller configure type Options IDE AHCI Serial ATA Port 0 1 2 3 4 5 Description Not installed You can make no changes here MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 RAID BIOS IDE Configuration Sub menu AHCI Mode IDE Controller Enabled HDC Configure as AHCI gt Software Feature Mask Configuration Aggressive LPM Support Enabled SATA Port 0 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 1 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 2 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 3 HotPlug Disabled Spin Up Device Disabled POPE ltiplier Disabled SATA Port 4 HotPlug Disabled Spi
12. is selected a verified factory setup is loaded BIOS Rev 3 5 F9 Setup Defaults F10 Save and Exit On the first BIOS setup configuration this loads safe values for setup which make the board boot up MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 BIOS 3 6 5 Load Custom Defaults If this option is selected the custom defaults that have been saved in a former session with Save Custom Defaults are loaded For details see Chapter 3 6 6 Save Custom Defaults 3 6 6 Save Custom Defaults Save custom defaults 3 6 7 Discard Changes Discard changes MEN Mikro Elektronik GmbH 77 20F021P00 E4 2015 01 13 Maintenance 4 Maintenance 4 1 Lithium Battery The board contains a lithium battery There is a danger of explosion if the battery is incorrectly replaced Replace only with the same or equivalent type Manufacturer Renata Type CR2032 Capacity 235 mAh Dispose of used batteries according to the manufacturer s instructions Figure 3 Position of battery on the mass storage adapter on the F21P mSATA disk microSD card bottom USB Ethernet VGA Battery MEN Mikro Elektronik GmbH 78 20F021P00 E4 2015 01 13 5 Appendix 54 Appendix Literature and Web Resources A lef
13. this publication are identified by the trademarks service marks or product names as designated by the companies which market those products The trademarks and registered trademarks are held by the companies producing them Inquiries concerning such trademarks should be made directly to those companies Conformity MEN products are no ready made products for end users They are tested according to the standards given in the Technical Data and thus enable you to achieve certification of the product according to the standards applicable in your field of application MEN Mikro Elektronik GmbH 14 20F021P00 E4 2015 01 13 About this Document RoHS Since July 1 2006 all MEN standard products comply with RoHS legislation Since January 2005 the SMD and manual soldering processes at MEN have already been completely lead free Between June 2004 and June 30 2006 MEN s selected component suppliers have changed delivery to RoHS compliant parts During this period any change and status was traceable through the MEN ERP system and the boards gradually became RoHS compliant WEEE Application The WEEE directive does not apply to fixed industrial plants and tools The compliance is the responsibility of the company which puts the product on the market as defined in the directive components and sub assemblies are not subject to product compliance In other words Since MEN does not deliver ready made products to end users the WEEE directive
14. 01 13 Tu Getting Started 1 4 Troubleshooting at Start up If you have any problems at start up of the F21P you can start the board with EFI default settings for troubleshooting For more Information on the BIOS see Chapter 3 BIOS on page 56 1 5 Configuring BIOS The F21P is equipped with an InsydeH2O UEFI framework Normally you won t need to make any changes in the BIOS setup If you do however you find further details on the F21P s BIOS in Chapter 3 BIOS on page 56 1 6 Installing Operating System Software The board supports Windows Linux VxWorks on request and QNX on request E You can find any software available on MEN s website the respective manufacturer s documentation on how to install By standard no operating system is installed on the board Refer to operating system software 1 6 1 Installing Windows XP or Windows 7 on USB Devices The microSD card of the F21P is connected via USB A standard Windows operating system like Windows XP Professional or Windows 7 Ultimate does not support direct installation on USB memory devices There are three possible solutions nstall the operating system on the mSATA disk of the F21P Add a hard drive SATA mSATA on a peripheral board or side card Switch to an Embedded Windows like Windows Embedded Standard or Win dows Embedded Standard 7 These Embedded Windows operating systems sup port being installed on an
15. 1 13 BIOS PCI Express Configuration gt PCI Express Root Port 1 PCI Express Root Port 1 Enabled SPC Press Root Port 2 PCI Express Root Port 2 Enabled SPC Bress Root Port 3 PON Express koor Port 3 Enabled gt PCI Express Root Port 4 PCI Express Root Port 4 Enabled gt PCI Express Root Port 5 PCL Express Root Port 5 Enabled gt PCI Express Root Port 6 PCI Express No Port 6 Enabled SCH Express oot Port PCI Express koor Port J Enabled gt PCI Express Root Port 8 ACH Express Root Port amp Enabled PCI Express Root Port 1 2 3 4 5 6 Description Enable disable PCI Express Root Ports If PCI Express Root Port 1 is disabled PCI Express Root Ports 2 to 6 will also be disabled Options Enabled Disabled Platform Configuration WSIOS Wears ZL EC Ver N A CPUID 206A5 PCH Rev 0x03 SA Rev 0x07 Microcode Rev 0x07 Number of Core 4 Number of Thread per Core 2 VT d Supported VMX Supported SMX TXT Supported Platform Configuration Description In this menu fixed system values are listed No changes can be made here Extended ICC ICC Overclocking Lib J 50 11 51 ICC Overclocking Lib Description Integrated clock control for overclocking operations and dynamic ICC control For information only MEN Mikro Elektronik GmbH 69 20F021P00 E4 2015 01 13 BIOS 3 3 Security InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Powe
16. 12 2 Rear I O Connection The third Ethernet interface is controlled via a PCI Express xl link from the processor and available at the J2 rear I O connector in compliance with CompactPCI PlusIO standard PICMG 2 30 As an option one of the front Ethernet interfaces can be led to the J2 connector A special board version is required for this On this board version the lower front Ethernet interface with AMT functionality cannot be used For the J2 rear I O pin assignments see Chapter 2 16 1 CompactPCI PluslO Rear I O on page 50 E Contact MEN s sales staff for further information MEN Mikro Elektronik GmbH 38 20F021P00 E4 2015 01 13 Functional Description 2 13 High Definition HD Audio Interface The F21P provides an HD audio interface accessible via a side card Embedded audio on DisplayPort and HDMI is supported Also see Chapter 2 14 Side Card Interface on page 40 for further details on the side card interface E See MEN s website for available side cards Also see Chapter 5 1 Literature and Web Resources on page 79 for literature on HD audio MEN Mikro Elektronik GmbH 39 20F021P00 E4 2015 01 13 Functional Description 2 14 Side Card Interface MEN offers a number of side cards for F21P featuring different I O functionality The side cards are all standard 3U Eurocards in 4 HP single width Access to I O connectors is given directly from the front panel The s
17. 2 0 ports The F21P can be extended by different side cards Additional functions include a digital video interface for flat panel connection via DVI multimedia a variety of different UARTs or another four USBs SATA for hard disk connection and HD audio Thermal supervision of the processor and a watchdog for the operating system complete the functionality of the F21P As an option a TPM Trusted Platform Module chip can be assembled The F21P operates in Windows and Linux environments as well as under real time operating systems that support Intel s multi core architecture The InsydeH20 EFI BIOS was specially designed for embedded system applications Equipped with Intel components exclusively from the Intel Embedded Line the F21P has a guaranteed minimum standard availability of 7 years The F21P is suited for a wide range of industrial applications e g for monitoring vision and control systems as well as test and measurement Main target markets comprise industrial automation multimedia traffic and transportation aerospace shipbuilding medical engineering and robotics The F21P comes with a tailored passive heat sink within 4 HP height The robust design of the F21P make the board especially suited for use in rugged environments with regard to shock and vibration according to applicable DIN EN or IEC industry standards The F21P is also ready for coating so that it can be used in humid and dusty environments
18. 20F021P00 E4 2015 01 13 F21P 3U CompactPCI PluslO Intel Core i7 CPU Board ME F21P 3U CompactPCI PluslO Intel Core i7 CPU Board F21P 3U CompactPCI PluslO Intel Core i7 CPU Board The F21P versatile 4HP 3U single board computer is a continuation of MEN s proven range of Intel CPU boards It is equipped with the high performance second generation Intel Core i7 processor running at 2 1 GHz and offering the latest quad core processor architecture from Intel with full 64 bit support The CPU card delivers an excellent graphics performance and is designed especially for embedded systems which require high computing performance with low power consumption The F21P offers a 32 bit 33 MHz CompactPCI bus interface and can also be used without a bus system 4 USB 2 0 ports 4 PCI Express x1 links 2 SATA 3 Gb s and 2 SATA 6 Gb s interfaces as well as one Gigabit Ethernet are led to the J2 rear I O connector which is compatible with the PICMG 2 30 CompactPCI PlusIO specification The F21P is equipped with fast DDR3 DRAM which is soldered to the F21P to guarantee optimum shock and vibration resistance An mSATA disk and a microSD card device which are connected via a USB interface and a SATA channel offer nearly unlimited space for user applications The standard I O available at the front panel of F21P includes graphics on a VGA connector two PCIe driven Gigabit Ethernet as well as two USB
19. 4 Load Optimal Defaults anas nara vag ange caw reos 76 3 6 5 Load Custom Detaults osos RR RR e TI 3 6 0 Save Custom Defaults a id vennen ve oat gekent TH 3 6 7 Discard Changes 2s oss oo e Rr ete Td d4 Maintenance sccwacied PEE RES 3 dR AREE ELRR ERE REPRE FERE DERE 78 del thin Battery ober sombrero ann eben 78 5 Appendix eie eor rr hx PI ePER eee ene 79 5 1 Literature and Web RESOUICES nan an naan ener es 79 Sud CPU tana cud sented ecanseid ORI RGUE UR ERE cea DERI E 79 5 12 SATA aranse gara repta ka ERA PC TER b rd 79 SMES USB ton icono mined he ee Duque SERIE aed SMe 79 JLA Bthemet iss ooo Rr RR sete Ret aoe Rae be 79 Sis HDAVI oos poA TERANE be 80 ILO PELBXPIESS vanbenedeni 80 51 7 dCompactPCl saas annae sandrine eb dd 80 2 8 CompactPCI PluslQ ox sonen brede E 80 5 2 Finding out the Product s Article Number Revision and Serial Numbers xoa Sota sa steat bedie satu dn 81 MEN Mikro Elektronik GmbH 17 Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Processor coro options on F2IP 222 od ox pd cte eR eek hee 27 Pin assignment of 15 pin HD Sub VGA receptacle connector 39 Signal mnemonics of 15 pin HD Sub VGA connector 33 Pin assignment of USB front panel connectors 35 Signal mnemonic
20. 5 01 13 Functional Description 2 9 2 1 Inserting and Extracting a microSD Card The microSD card has to be installed before the mSATA disk as it is difficult to access it afterwards To install a microSD card stick to the following procedure Mi Power down your system and remove the F21P from the system MI Put the board on a flat surface MI Insert the microSD card into the slot with the contacts at the top PANU M Make sure that it clicks into place properly Mi For extracting the card push it down and pull it out MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Functional Description 2 9 3 mSATA Disk The mSATA disk is controlled via a SATA channel from the chipset The F21P is shipped without an mSATA disk installed E See MEN s website for ordering options 2 9 3 4 Installing an mSATA Disk To install an mSATA disk stick to the following procedure M Power down your system and remove the F21P from the system MI Put the board on a flat surface Ml Insert the mSATA disk carefully in a 30 angle TULLLULLLLLL LD A patent pmen main em M Make sure that all the contacts are aligned properly and the card is firmly con nected with the card connector MEN Mikro Elektronik GmbH 31 20F021P00 E4 2015 01 13 Functional Description MI Fix the card using two M2 5 x4 screws and two spacers highlighted in red mSATA disk microSD card bottom
21. 7 PCIE1 TX 18 PCIE3 TX 19 GND GND 20 GND 21 PCIE1 RX 22 PCIE3_RX 23 PCIE1_RX 24 PCIE3_RX 25 GND 26 GND 27 PCIEO_TX 28 PCIE2_TX 29 PCIEO TX 30 PCIE2 TX ES GND 32 GND 33 PCIEO_RX 34 PCIE2_RX 35 PCIEO_RX 36 PCIE2_RX 37 GND 38 GND Note There is one SATA port on the side card connector which can be switched to Port A or Port B via the BIOS PCI Express port 3 can be implemented on a special board version instead of port 1 MEN Mikro Elektronik GmbH 41 20F021P00 E4 2015 01 13 Functional Description 39 3 3V 40 3 3V 42 HDA SYNC 44 HDA BIT CLK 46 HDA _RST 48 HDA SDOUT 50 HDA_SDIN 39 52 GND 54 PCIE_WAKE 56 PLT_RST 58 9V 60 SMB_CLK 62 SMB_DATA 64 GND 77 66 DPB OB AUX p SDVO CTRLCLK 68 DPB OB AUX n SDVO_CTRLDATA 69 GND 70 GND 71 PCIE_CLK_A_REF 72 PCIE_CLK_B_REF 73 PCIE_CLK_A_REF 74 PCIE_CLK_B_REF 75 GND 76 GND Note The signals marked in gray are multiplexed MEN Mikro Elektronik GmbH 42 20F021P00 E4 2015 01 13 Functional Description Table 11 Pin assignment of 114 pin side card connector pins 77 114 m GND 78 GND 79 SDVO TVCLKIN 80 SDVO_FLDSTALL 81 SDVO TVCLKIN 82 SDVO FLDSTALL TE GND 84 GND 85 DDPB 2 n 86 DDPC 2 n 87 DDPB 2 p 88 DDPC 2 p 89 GND 90 GND 91 DDPB 1 n 92 DDPC 1 n 93 DDPB 1 p 94 DDPC 1 p 95 GND GND 96 GND 97 DDPB 0 n 98 DDPC 0 n i BM 99 DDPB 0 p 100 DDPC 0 p 101 GND 102
22. GND 108 DDPB 3 n 104 DDPC 3 n 105 DDPB 3 p 106 DDPC 8 p 107 GND 108 GND 109 SDVO_INT 110 DDP CTRDATA us 14 111 SDVO_INT 112 DDP CTRLCLK 113 GND 114 DDPC_HPD MEN Mikro Elektronik GmbH 43 20F021P00 E4 2015 01 13 Functional Description Table 12 Signal mnemonics of 114 pin side card connector Signal Direction Function Power 3 3V out 3 3 V power supply 5V out 5 V power supply GND Digital ground of respective interface SATA Port SATA_A_RX in Differential pair of SATA receive lines port A AorB SATA_A_RX depending sata _A_TX out Differential pair of SATA transmit lines port A on BIOS SUN pe setting F SE SATA B RX in Differential pair of SATA receive lines port B SATA B RX SATA B TX out Differential pair of SATA transmit lines port B SATA B TX PCI PCIE CLK A REF out Reference clock A 100 MHz Express PCIE CLK A REF PCIE CLK B REF out Reference clock B 100 MHz PCIE CLK B REF PCIEO_RX in Differential pair of PCle receive lines port O PCIEO RX PCIEO TX out Differential pair of PCle transmit lines port O PCIEO TX PCIE1_RX in Differential pair of PCle receive lines port 1 PCIE1_RX PCIE1_TX out Differential pair of PCle transmit lines port 1 PCIE1_TX PCIE2 RX in Differential pair of PCle receive lines port 2 PCIE2 RX PCIE2 TX out Differential pair of PCle transmit lines po
23. I bus devices In combination with a specific side card the F21P can also perform system slot functionality in a CompactPCI Express system 2 16 1 CompactPCI PluslO Rear I O The F21P is also compliant to the CompactPCI PlusIO standard PICMG 2 30 This means that it offers a fixed pin assignment of one Gigabit Ethernet 4 SATA 4 PCI Express and 4 USB interfaces at the J2 connector A second Gigabit Ethernet interface can be implemented by switching one front interface to the rear As a result the pin assignment of the F21P rear I O connector J2 is not compliant anymore to the rear I O of the F14 F15 F17 and F18 MEN offers a rear I O transition module on which all interfaces from the J2 connector can be accessed the CT12 Note The F21P supports one Gigabit Ethernet interface at the rear whereas the PICMG 2 30 CompactPCI PlusIO standard supports up to two d See MEN s website for further information 2 16 2 CompactPCI Connector J1 The pin assignment of connector J1 as defined in the CompactPCI specification will not be repeated here The voltage supply for the battery can optionally be made available on the A4 pin on the conduction cooled board version 2 16 3 CompactPCI Connector J2 The table below shows the fixed pinout of the J2 connector as defined in the PICMG 2 30 CompactPCI PlusIO standard MEN Mikro Elektronik GmbH 50 20F021P00 E4 2015 01 13 Table 13 Pin assignment of CompactPCI connector J2 F
24. MEN Mikro Elektronik GmbH 2 20F021P00 E4 2015 01 13 Diagram PCle x1 USB 2 0 USB 2 0 SATA SATA 3Gb VGA HD Audio USB 2 0 HDMI USB 2 0 HDMI SDVO Pele xt f CIe PCI bridge cPCI PCle x1 cles Gb Ethernet PCle x1 PCle x1 Instead of one rear interface Instead of one front interface USB 2 0 Q Front connector sasen Q Rear I O connector Onboard connector weeen 1 i Options PCle x1 SGPIO MEN Mikro Elektronik GmbH 3 20F021P00 E4 2015 01 13 Technical Data Technical Data CPU Intel Core i7 2715QE Up to 2 1 GHz processor core frequency 3 GHz maximum turbo frequency Chipset Intel QM67 Platform Controller Hub PCH Memory Up to 6 MB last level cache integrated in i7 Up to 16 GB SDRAM system memory Soldered DDR3 with ECC support 1066 1333 1600 MHz memory bus frequency 64 Mbits boot Flash Serial EEPROM 2kbits for factory settings Mass Storage microSD card interface Connected via one USB port mSATA disk slot Connected via one SATA channel Serial ATA SATA Four channels via rear I O one channel via side card connector one channel for mSATA disk 4 SATA 3 Gbit s interfaces 2 SATA 6 Gbit s interfaces rear I O RAID level 0 1 5 10 support Graphics ntegrated in QM67 chipset 650 MHz graphics base frequency 1 2 GHz graphics maximum dynamic frequency VGA connector
25. OOB diagnostics remote control IDE Redirect Serial over LAN SOL agent presence checking and network traffic filtering AMT is supported on the lower front Ethernet interface ETH2 of the F21P For information on how to enable the AMT BIOS extension see Chapter 3 BIOS 3 MEN provides an application note on how to switch on the AMT E functionality and log onto the CPU board via VNC afterwards If the supercapacitor and or the battery is empty the F21P loses its complete AMT settings due to Intel s security standards As an option a BIOS setting can be implemented which makes it possible to switch the AMT interface to the backplane via the Ethernet rear I O card In this case there is only one Ethernet interface ETH1 available at the front panel en bef Contact MEN s sales team for further information 2 4 Trusted Platform Module As an assembly option a trusted platform module to protect the content of the SATA storage devices can be implemented on the F21P A TPM module compliant to the TPM v1 2 specification can be used QE Contact MEN s sales team for further information MEN Mikro Elektronik GmbH 26 20F021P00 E4 2015 01 13 Functional Description 2 5 Reset Behavior and Power States The F21P can be reset using the reset button on the front panel or the PBRST signal on the backplane It supports the S5 S4 S3 SO and Mx power states All voltages which are not requ
26. U boards Front panel 4HP with ejector Weight 204 g w o heat sink MEN Mikro Elektronik GmbH 6 20F021P00 E4 2015 01 13 Technical Data Environmental Specifications Temperature range operation Depends on system configuration CPU hard disk heat sink Maximum 85 C Minimum 40 C all processors Conditions airflow 1 5m s typical power dissipation 12 W board versions with i7 2715QE processor with Windows XP operating system and 1 Gb Ethernet connection e Temperature range storage 40 85 C Relative humidity operation max 95 non condensing Relative humidity storage max 95 non condensing Altitude 300m to 2 000m e Shock 50 m s 30 ms Vibration Function 1 m s 5 Hz 150 Hz Vibration Lifetime 7 9 m s 5 Hz 150 Hz Conformal coating on request MTBF 417 879 h 40xC according to IEC TR 62380 RDF2000 Safety PCB manufactured with a flammability rating of 94V 0 by UL recognized manufacturers EMC Tested according to EN 55022 radio disturbance IEC 61000 4 3 electromagnetic field immunity IEC 61000 4 4 burst and IEC 61000 4 6 conducted disturbances BIOS e InsydeH2O UEFI Framework Intel Active Management Technology Manageability Engine in Chipset Network Filters in Chipset Dedicated Flash Storage Area Out of Band OOB Access Power off Access Independent of OS status Power status control Keyboard Video
27. ane 4 1 4 PE CLKE in Presence detect PCle lane 1 4 1 4 PE CLK out Differential 100 MHz Reference 1 4 PE_CLK Clock PCle lane 1 4 VGA CRT_R_DDC_CLK Display Data Channel clock optional car R ppc DAT Display Data Channel data lines on special A conduction cooled board version 2 16 4 Power Supply Status DEG FAIL Power supply failures may be detected before the system crashes down by monitoring the signals DEG or FAIL These active low lines are additions of the CompactPCI specification and may be driven by the power supply DEG signals the degrading of the supply voltages FAIL their possible failure MEN Mikro Elektronik GmbH 54 20F021P00 E4 2015 01 13 Functional Description 2 17 Reset Button and Status LED The F21P has a reset button and one status LED at the front panel The reset button is recessed within the front panel and requires a tool e g paper clip to be pressed preventing the button from being inadvertently activated The yellow status LED shows board status messages The LED is controlled by the board controller It is switched on when the BIOS starts switched off when the board is switched off and flashing slowly when the board is in stand by S3 status During normal operation the LED can be switched on and off using the MEN driver for the board controller QE See MEN s website for further information In case of a board failure the LED displays the follo
28. be changed except the Supervisor password Limited Only limited fields can be changed Set User Password Description Enter and confirm the user password under this menu item Clear User Password Description Clear the user password Only possible for a supervisor or user in the access levels full or limited MEN Mikro Elektronik GmbH 71 20F021P00 E4 2015 01 13 BIOS 3 4 Power InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Power Boot Exit gt Advanced CPU Control Wake on Lan Enabled F1 Help N Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt Select Menu Enter Select gt F10 Save and Exit Submenu Advanced CPU Control Sub Menu TXT Disable Active Processor Cores All Core HT Support Auto VT Support Enabled Hardware Prefetcher Enabled Adjacent CacheLine Prefetch Enabled Max CPUID value limit Disabled C States Enabled Turbo Mode Enabled TXT Description Enables utilization of additional hardware capabilities provided by Intel Trusted Execution Technology changes require a full power cycle to take effect Options Enabled Disabled Active Processor Cores Description Numbers of cores to enable in each processor package Options All Core 1 Core MEN Mikro Elektronik GmbH 72 20F021P00 E4 2015 01 13 BIOS 2 Core 3 Core 4 Core 5 Core 6 Core 7 Core HT Support Description Enable or disable Hyper Threading Options Auto Disabled VT Support D
29. ching Hubs Mode Cannot be changed Options Enabled Chipset Configuration Setup warning Setting items on this screen to incorrect values may cause your system to malfunction VT d Disabled VT d Description Check to enable VT d function on MCH Options Enabled Disabled MEN Mikro Elektronik GmbH 67 20F021P00 E4 2015 01 13 BIOS ACPI Table Feature Control APIC IO APIC Mode Enabled Watchdog ACPI Table Enabled APIC IO APIC Mode Description This item is valid only for WIN2k and WINXP Also a fresh install of the OS must occur when APIC Mode is desired Test the IO ACPI by setting item to Enable The APIC Table will then be pointed to by the RSDT the Local APIC will be initialized and the proper enable bits will be set in ICHAM Options Enabled Disabled Watchdog ACPI Table Description Enable disable to support watchdog ACPI Table WDAT Options Enabled Disabled Active Management Technology Support Intel AMT Support Enabled Watchdog Support Disabled 0S Timer 0 BIOS Timer 0 Intel AMT Support Description Enable disable Intel Active Management Technology BIOS extension Note iAMT H W is always enabled This option just controls the BIOS extension execution Options Enabled Disabled Watchdog Support Description Enable or disable Watchdog timer Options Enabled Disabled OS Timer BIOS Timer Description Set OS BIOS watchdog timer MEN Mikro Elektronik GmbH 68 20F021P00 E4 2015 0
30. ct the board and other components against damage from static electricity you should follow some precautions whenever you work on your computer Power down and unplug your computer system when working on the inside Hold components by the edges and try not to touch the IC chips leads or circuitry Use a grounded wrist strap before handling computer components Place components on a grounded antistatic pad or on the bag that came with the component whenever the components are separated from the system Only store the board in its original ESD protected packaging Retain the original packaging in case you need to return the board to MEN for repair Computer boards and components contain electrostatic sensitive MEN Mikro Elektronik GmbH ll 20F021P00 E4 2015 01 13 About this Document About this Document This user manual is intended only for system developers and integrators it is not intended for end users It describes the hardware functions of the board connection of peripheral devices and integration into a system It also provides additional information for special applications and configurations of the board The manual does not include detailed information on individual components data sheets etc A list of literature is given in the appendix History Issue Comments Date E1 First issue 2011 12 21 E2 Description of new board revision R02 PCle lanes 2012 08 31 on side card connector fr
31. d booted from a USB device Linux supports booting from a USB device without problems 17 Installing Driver Software For a detailed description on how to install driver software refer to the respective documentation 3 You can find any driver software and documentation available for gt download on MEN s website MEN Mikro Elektronik GmbH 24 20F021P00 E4 2015 01 13 Functional Description 2 Functional Description The following describes the individual functions of the board and their configuration on the board There is no detailed description of the individual controller chips and the CPU More information on the individual controller chips and the CPU can be obtained from the data sheets or data books of the semiconductor manufacturer concerned see Chapter 5 1 Literature and Web Resources on page 79 2 1 Power Supply The power sequence is compliant to the ATX Power Supply Design Guide There are only two possible ways to power the F21P 5V 3 3V and 12V via CompactPCI connector J1 5V only via CompactPCI connector J1 To supply the board with 3 3V and 5V is not allowed and may cause A serious damage If 3 3V are supplied via CompactPCI connector J1 the 12V supply always has to be present If the 12V are not present the board automatically generates 3 3V and also feeds them to the backplane which would cause a conflict with the external 3 3V supply 2 2 B
32. de Disabled Primary Display Description Set the primary display For an external graphic device PEG or PCI has to be set Options Auto Scans and activates the graphics devices with the following priority IGFX integrated graphics PEG PCI Express graphics PCI graphics card at the PCI bus PEG IGFX PCI Internal Graphic Device Description Enable internal graphic device Options Enabled Disabled Auto IGD DVMT Pre Allocated Description Select DVMT5 0 Pre Allocated Fixed Graphics Memory size used by the Internal Graphics Device Options 32 MB 64 MB 96 MB 128 MB IGD Gfx Low Power Mode Description Applicable for SFF only Options Enabled Disabled MEN Mikro Elektronik GmbH 66 20F021P00 E4 2015 01 13 BIOS USB Configuration Sub menu Setup Warning Disabling USB devices or ports may cause your system to not enter setup and to prevent reenabling of USB devices or ports USB Legacy Enabled ERICH 3 Enabled ERICH 2 Enabled Per Port Control Disabled USB RMH Mode Enabled USB Legacy Description If this menu item is enabled it is possible to boot from USB devices and use a USB keyboard under DOS Cannot be changed Options Enabled EHCI 1 2 Description Enable Disable EHCI 1 2 Options Enabled Disabled Per Port Control Description Enable Disable the per port disable control override Options Enabled Disabled USB RMH Mode Description Enable Disable the PCH USB Rate Mat
33. eaning to the board or component out meaning from it the board or component About this Document Legal Information Changes MEN Mikro Elektronik GmbH MEN reserves the right to make changes without further notice to any products herein Warranty Guarantee Liability MEN makes no warranty representation or guarantee of any kind regarding the suitability of its products for any particular purpose nor does MEN assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages TO THE EXTENT APPLICABLE SPECIFICALLY EXCLUDED ARE ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW CUSTOM OR USAGE INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR USE In no event shall MEN be liable for more than the contract price for the products in question If buyer does not notify MEN in writing within the foregoing warranty period MEN shall have no liability or obligation to buyer hereunder The publication is provided on the terms and understanding that 1 MEN is not responsible for the results of any actions taken on the basis of information in the publication nor for any error in or omission from the publication and 2 MEN is not engaged in rendering technical or other advice or services MEN expressly disclaims all and any liability and re
34. escription Enable or disable Vanderpool technology Options Enabled Disabled Hardware Prefetcher Description Enable disable MLC Mid level cache L2 cache streamer prefetcher Options Enabled Disabled Adjacent CacheLine Prefetch Description Enable disable MLC Mid level cache L2 cache spatial prefetcher Options Enabled Disabled Max CPUID value limit Description Limit CPUID max value to 3 if max CPUID value gt 3 This setting is useless for windows OS Options Enabled Disabled C States Description Enable processor idle power saving states C States Options Enabled Disabled Turbo Mode Description Enable processor Turbo Mode requires EMTTM enabled too Options Enabled Disabled Wake on Lan Description Determines the action taken when the system power is off anda Wake on Lan event occurs Options Enabled Disabled MEN Mikro Elektronik GmbH 73 20F021P00 E4 2015 01 13 BIOS 3 5 Boot InsydeH20 Setup Utility Rev 3 5 Main Advanced Security Power Boot Exit UEFI Boot Enabled Quick Boot Enabled Quiet Boot Enabled PXE Boot to LAN Disabled ACPI Selection ACPI 3 0 USB Boot Enabled EFI Device First Disabled EFI F1 Help N Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit lt Select Menu Enter Select gt F10 Save and Exit Submenu UEFI Boot Description Enable Disable UEFI Boot Function Options Enabled Disabled Quick Boot Description Allows InsydeH20O to skip certain t
35. ests while booting This will decrease the time needed to boot the system Options Enabled Disabled Quiet Boot Description Disables or enables booting in Text Mode Options Enabled Disabled PXE Boot to LAN Description Disables or enables PXE boot to LAN Options Enabled Disabled ACPI Selection Description Select booting to Acpi3 0 Acpi1 0B Options Acpi3 0 Acpi1 0B MEN Mikro Elektronik GmbH 74 20F021P00 E4 2015 01 13 c LLL BIOS USB Boot Description Disables or enables booting to USB boot devices Options Enabled Disabled EFI Device First Description Determines whether the EFI device or the legacy device is booted first If enabled the EFI device is booted first If disabled the legacy device is booted first Options Enabled Disabled MEN Mikro Elektronik GmbH 75 20F021P00 E4 2015 01 13 3 6 Exit InsydeH20 Setup Utility Main Advanced Security Power Boot Exit Exit Saving Changes Save Change Without Exit Exit Discarding Changes Load Optimal Defaults Load Custom Defaults Save Custom Defaults Discard Changes F1 Help N Select Item F5 F6 Change Values Esc Exit lt Select Menu Enter Select gt Submenu 3 6 1 Exit Saving Changes Exit system setup and save your changes 3 6 2 Save Change Without Exit Save your changes without exiting the system 3 6 3 Exit Discarding Changes Exit system setup without saving your changes 3 6 4 Load Optimal Defaults If this option
36. g system and its loader Together these provide a standard environment for booting an operating system and running pre boot applications This product line is the next generation of PC BIOS technology The gt character in front of a menu item means that a sub menu is available An x in front of a menu item means that there is a configuration option which needs to be activated through a higher configuration option before being accessible The F21P BIOS has two configuration modes One mode shows only a selection of the most important items and hides items where normally no changes in the settings are required This manual only describes the short mode You can easily switch between the two modes via a menu item For more details see Chapter Full Configuration Mode on page 58 MEN Mikro Elektronik GmbH 56 20F021P00 E4 2015 01 13 BIOS 3 1 Main InsydeH20 Setup Utility Rev 3 5 F1 Help Select Item F5 F6 Change Values F9 Setup Defaults Esc Exit Select Menu Enter Select F10 Save and Exit Submenu MEN Mikro Elektronik GmbH 57 20F021P00 E4 2015 01 13 BIOS InsydeH2O0 Version MEN Board Processor Type System Bus Speed System Memory Speed Cache RAM Total Memory Intel ME Version MEN EC Version SODIMM 0 SODIMM 1 Description You cannot change any values in these fields They are only for information Language Description Select the default language Options English System
37. h a dedicated one piece two slot front panel Align the F21P s front panel connectors with the side card s front panel and align the board to board connector of the side card with the side card connector of F21P Press the board to board connectors together orn ARANAANN Board to board connection MEN Mikro Elektronik GmbH 47 20F021P00 E4 2015 01 13 Functional Description Front panel mounting screws at bottom side of board v g gt o a o o mS w o ES MI Fasten the side card standoff using the spring and screw provided with the side card at the top of the side card THREEII Vl Reinsert the board into your system MEN Mikro Elektronik GmbH 48 20F021P00 E4 2015 01 13 Functional Description 2 15 PCI Express 2 15 1 General PCI Express PCIe succeeds PCI and AGP and offers higher data transfer rates As opposed to the PCI bus PCIe is no parallel bus but a serial point to point connection Data is transferred using so called lanes with each lane consisting of a line pair for transmission and a second pair for reception Individual components are connected using switches At the electrical level each lane consists of two unidirectional LVDS Low Voltage Differential Signaling pairs Transmit and receive are separate differential pairs for a total of 4 data wires per lane PCIe supports full duplex operation and uses a clock rate of 1 25 GHz This resul
38. ide card connector is located at the top side of the board so that one side card can be attached to the right side of the F21P As an option the F21P can also be supplied with the side card connector at the bottom side so that the side card may be attached to the left side of the CPU The side card connector on F21P supports the following interfaces One SATA channel switchable to port A or B via BIOS Four USB interfaces Three PCI Express x1 links HD audio interface One digital video output supporting SDVO DisplayPort and HDMI Port B One digital video output supporting DisplayPort and HDMI Port C connector are protected against a short circuit situation This connector therefore should be used exclusively for attachment of a side card Neither the 3 3V nor the 5V pins of the expansion interface e See MEN s website for available side cards and board versions 2 14 4 Connection Connector types 114 pin matched impedance receptacle connector MICTOR 0 64 mm grid Mating connector 114 pin matched impedance plug connector MICTOR 0 64 mm grid MEN Mikro Elektronik GmbH 40 20F021P00 E4 2015 01 13 Functional Description Table 9 Pin assignment of 114 pin side card connector pins 1 38 1 GND 2 GND 1 2 NE SATA_A_TX 4 SATA_B_TX 5 SATA_A_TX 6 SATA_B_TX 7 GND 8 GND 9 SATA_A_RX 10 SATA_B_RX 11 SATA_A_RX 12 SATA_B_RX 13 GND 14 GND 15 PCIE1_TX 16 PCIE3_TX 39 on 1
39. ification Revision 1 0 Mating connector 4 pin USB Series A plug according to Universal Serial Bus Specification Revi sion 1 0 Table 4 Pin assignment of USB front panel connectors 1 5V i 2 USB_D i 3 USB_D 4 GND Table 5 Signal mnemonics of USB front panel connectors Signal Direction Function 5V out 5 V power supply GND Digital ground USB_D USB_D in out USB lines differential pair 2 11 2 Side Card Connection Four USB interfaces are accessible via a side card See Chapter 2 14 Side Card Interface on page 40 for further details on the side card interface e See MEN s website for available side cards and board versions 2 11 3 Rear I O Connection CompactPCI PluslO Four USB interfaces are accessible via rear I O in compliance to the CompactPCI PlusIO standard PICMG 2 30 See Chapter 2 16 1 CompactPCI PluslO Rear I O on page 50 for information on J2 rear I O pin assignments MEN Mikro Elektronik GmbH 35 20F021P00 E4 2015 01 13 Functional Description 2 12 Ethernet Interfaces The F21P has three Ethernet interfaces connected to the processor and the PCH via three x1 PCI Express PCIe links They are controlled by two Intel 82574L Ethernet controllers and one Intel 82579LM Ethernet PHY They support 10 Mbits s up to 1000 Mbits s as well as full duplex operation and autonegotiation The lower front interface supports AMT
40. ignal mnemonics of CompactPCI connector J2 CompactPCI and CompactPCI PluslO rear I O Signal Direction Function CompactPC CLK 6 1 out Clocks 1 to 6 l PBRST in Push button reset DEG in Power supply degenerate FAIL in Power supply fail PWRBTN in Power button REQ GNT 6 1 in out Request grant pairs 1 to 6 MEN Mikro Elektronik GmbH 52 20F021P00 E4 2015 01 13 Functional Description Signal Direction Function SGPIO SATA_SC out Clock signal SATA_SL out Last clock of a bit stream begin a new bit stream on the next clock SATA_SDO out Serial data output bit stream SATA_SDI in Serial data input bit stream may not be supported by all SGPIO y devices MEN Mikro Elektronik GmbH 53 20F021P00 E4 2015 01 13 Functional Description Signal Direction Function PCI 1_PE_Rx00 in Differential PCle receive lines lane Express 1_PE_Rx00 1 1_PE_Tx00 out Differential PCle transmit lines 1_PE_Tx00 lane 1 2_PE_Rx00 in Differential PCle receive lines lane 2 PE Rx00 2 2 PE Tx00 out Differential PCle transmit lines 2 PE Tx00 lane 2 3 PE Rx00 in Differential PCle receive lines lane 3 PE Rx00 3 3 PE Tx00 out Differential PCle transmit lines 3 PE Tx00 lane 3 4 PE Rx00 in Differential PCle receive lines lane 4 PE Rx00 4 4 PE Tx00 out Differential PCle transmit lines 4 PE Tx00 l
41. ired are deactivated while the board is into a lower power state See also Chapter 2 17 Reset Button and Status LED on page 55 2 6 Real Time Clock The board includes a real time clock connected to the chipset For data retention during power off the RTC is backed up by a supercapacitor The supercapacitor gives an autonomy of approx 14 hours when fully loaded Under normal conditions replacement should be superfluous during lifetime of the board The RTC can generate interrupt requests to the chipset The RTC has an accuracy of approximately 1 7 seconds day 11 minutes year at 25 C For retention of time date data after a power off of more than 8 10 hours the RTC is also backed by a battery e For ordering options see MEN s website 2 7 Processor Core The F21P can be equipped with different types of Intel 17 15 or Celeron processors The following table gives a performance overview Table 1 Processor core options on F21P Processor Type Core Frequency S dsl Co inl e Cache S ull rt Intel Core i7 2715QE 2 1 GHz 4 8 45 W 6 MB yes Intel Core i7 2655LE 2 2 GHz 2 4 25 W 4 MB yes Intel Core i7 2610UE 1 5 GHz 2 4 17 W 4 MB yes Intel Core i5 2515E 2 5 GHz 2 4 35 W 3 MB yes Intel Core i3 2340UE 1 3 GHz 2 4 17W 3MB no Intel Core i3 2310E 2 1 GHz 2 4 35W 3MB no Intel Celeron B810E 1 6 GHz 2 2 35 W 2 MB no Intel Celeron 847E 1 1 GHz 2 2 17 W 2 MB no Intel Celeron 827E 1 4
42. is not applicable for MEN Users are nevertheless recommended to properly recycle all electronic boards which have passed their life cycle Nevertheless MEN is registered as a manufacturer in Germany The registration number can be provided on request Copyright 2014 MEN Mikro Elektronik GmbH All rights reserved Germany MEN Mikro Elektronik GmbH Neuwieder StraBe 3 7 90411 Nuremberg Phone 49 911 99 33 5 0 Fax 49 911 99 33 5 901 E mail info men de www men de MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 France MEN Mikro Elektronik SAS 18 rue Ren Cassin ZA de la Ch telaine 74240 Gaillard Phone 33 0 450 955 312 Fax 33 0 450 955 211 E mail info men france fr www men france fr USA MEN Micro Inc 860 Penllyn Blue Bell Pike Blue Bell PA 19422 Phone 215 542 9575 Fax 215 542 9577 E mail sales menmicro com www menmicro com Contents Contents L Getting Started senses nn P ot beten nee Deen de Be 20 LI Mapotthe Board sns auo ud ed Hg apu ht od bdo paie d 20 1 2 Configuring the Hardware a suna eth mmn 27 1 3 Integrating the Board into a System en 23 1 4 Troubleshooting at Start up oee 24 15 Contignrng BIOS var hebr pta betu ee ye 24 1 6 Installing Operating System Software aen 24 1 6 1 Installing Windows XP or Windows 7 on USB Devices 24 1 7 Installing Driver SolbWale cu snie vastere dens re Spa 24 2 Functional Description s one er nU va
43. n SDVO_TVCLKIN clock differential pair SDVOCTRL_CLK in out I2C based control signal clock for SDVO shared with device needed when interface B is used as DPB_OB_AUX_p SDVO SDVOCTRL_DATA in out I2C based control signal data for SDVO device shared with needed when interface B is used as SDVO DPB OB AUX n Other PLT_RST out Platform reset global reset SMB_CLK out System Management Bus clock SMB_DATA in out System Management Bus data MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Functional Description 2 14 2 Installing a Side Card Perform the following steps to install a side card M Power down your system and remove the F21P from the system M Remove the front panel Loosen and remove the screws highlighted in red F22P Standard isu PT TIME Front panel mounting screws at bottom side of board VOA ED M Remove the front panel ejector from the F21P front panel Loosen the ejector screw at the back of the front panel Ml Install the ejector on the side card s front panel MEN Mikro Elektronik GmbH 46 20F021P00 E4 2015 01 13 annees LLL Functional Description Ml Install the side card standoff supplied with the side card in the mounting hole indicated in red in the following picture Note that two different standoffs are supplied with the side card For the F21P the longer standoff M2x18 72 I I is required MI Each side card comes wit
44. n Up Device Disabled Port ltiplier Disabled SATA Port 5 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled gt Serial ATA Port 0 Not Installed gt Serial ATA Port 1 Not Installed gt Serial ATA Port 2 Not Installed gt Serial ATA Port 3 Not Installed gt Serial ATA Port 4 Not Installed gt Serial ATA Port 5 Not Installed IDE Controller Description Enables or disables the IDE controllers Options Enabled Disabled HDC Configure as Description Set hard disk controller configure type Options IDE RAID AHCI Software Feature Mask Configuration Description The RAID OROM RST driver will refer to the SWFM configuration to enable disable the storage feature Aggressive LPM Support Description Enable disable the aggressive link power management SALP support Options Enabled Disabled SATA Port 0 1 2 3 Hot Plug Description Enable disable Hot Plug Not supported on SATA ports 4 and 5 Options Enabled Disabled MEN Mikro Elektronik GmbH 61 20F021P00 E4 2015 01 13 BIOS SATA Port 0 1 2 3 4 5 Spin Up Device Description Enable disable support of staggered spin up SSS Options Enabled Disabled SATA Port 0 1 2 3 4 5 Port Multiplier Description Enable disable support of port multiplier PMS Options Enabled Disabled Serial ATA Port 0 1 2 3 4 5 Description Not installed You can make no changes here MEN Mikro Elektronik GmbH 62 20F021P00 E4 2015 01 13 BIOS IDE Co
45. nfiguration Sub menu RAID Mode IDE Controller Enabled HDC Configure as RAID gt Software Feature Mask Configuration Aggressive LPM Support Enabled Alternate ID Disabled SATA Port 0 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 1 HotPlug Disabled Spin Up Device Disabled Pot ltiplier Disabled SATA Port 2 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 3 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled SATA Port 4 Hot g Disabled Spin Up Device Disabled POPE ltiplier Disabled SATA Port 5 HotPlug Disabled Spin Up Device Disabled Port ltiplier Disabled gt Serial ATA Port 0 Not Installed gt Serial ATA Port 1 Not Installed gt Serial ATA Port 2 Not Installed gt Serial ATA Port 3 Not Installed gt Serial ATA Port 4 Not Installed gt Serial ATA Port 5 Not Installed IDE Controller Description Enables or disables the IDE controllers Options Enabled Disabled HDC Configure as Description Set hard disk controller configure type Options IDE RAID AHCI Software Feature Mask Configuration Description The RAID OROM RST driver will refer to the SWFM configuration to enable disable the storage feature Aggressive LPM Support Description Enable disable the aggressive link power management SALP support O
46. nik GmbH 36 20F021P00 E4 2015 01 13 Functional Description Connection via RJ45 Connectors Connector types Modular 8 8 pin mounting jack according to FCC68 Mating connector Modular 8 8 pin plug according to FCC68 Table 7 Pin assignment and status LEDs of 8 pin RJ45 Ethernet 10 100 1000Base T connectors LAN1 LAN2 1 BI DA On Link up L 2 BI DA Off Link down e 3 BI DB 4 BI DC On Transmit or receive activity 5 BI DC Off No transmit or receive A 6 BI DB activity Blinking Transmit or receive 7 BI_DD activity 8 BI DD Connection via 9 pin D Sub Connector optional only 10Base T and 100Base TX are supported no Gigabit Ethernet A D Sub connector can be implemented as an option In this case connection The two interfaces are routed to one D Sub connector Connector types 9 pin D Sub plug according to DIN41652 MIL C 24308 with thread bolt UNC 4 40 Mating connector 9 pin D Sub receptacle according to DIN41652 MIL C 24308 available for rib bon cable insulation piercing connection hand soldering connection or crimp connection Table 8 Pin assignment of 9 pin D Sub 10Base T 100Base TX plug connector LAN1 LAN2 1 LAN2_TX s e9 6 LAN2TX 2 LANI TX Se 7 LAN1_TX 3 oles 8 LANIRX 4 LANI_RX 9 LAN2_RX 5 LAN2 RX MEN Mikro Elektronik GmbH 37 20F021P00 E4 2015 01 13 Functional Description 2
47. oard Supervision The F21P provides an intelligent board management controller BMC with the following main features Board power sequencing control Voltage supervision System watchdog Software reset functionality Error state logging Power mode settings SMBus communication with main CPU The watchdog device monitors the board on operating system level If enabled the watchdog must be triggered by application software If the trigger is overdue the watchdog initiates a board reset and this way can put the system back into operation when the software hangs The watchdog uses a configurable time interval or is disabled Settings are made through BIOS or via an MEN software driver In addition the F21P uses a temperature device to measure the local board temperature MEN Mikro Elektronik GmbH 25 20F021P00 E4 2015 01 13 Functional Description MEN provides dedicated software drivers for the board controller and the temperature device For a detailed description of the functionality of the driver software refer to the drivers documentation T 2 You can find any driver software and documentation available for download on MEN s website 2 3 Intel Active Management Technology AMT F21P boards equipped with an Intel Core i7 or i5 processor support Intel Active Management Technology AMT 7 0 Intel AMT is powered by a separate hardware engine in Intel chipsets which enables e g out of band
48. om PEG interface VGA and battery voltage via rear I O E3 Added TPM option extended AMT description 2013 05 23 minor restructuring of chapters cosmetics E4 Corrected options and minor errors added RTC 2014 01 13 accuracy reworked block diagram cosmetics MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 About this Document Conventions A Indicates important information or warnings concerning proper functionality of the product described in this document E E The globe icon indicates a hyperlink that links directly to the Internet where the latest updated information is available When no globe icon is present the hyperlink links to specific elements and information within this document italics bold mono comment IRQ IRQ in out MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Folder file and function names are printed in italics Bold type is used for emphasis A monospaced font type is used for hexadecimal numbers listings C function descriptions or wherever appropriate Hexadecimal numbers are preceded by 0x Comments embedded into coding examples are shown in green text Signal names followed by a hashtag or preceded by a forward slash indicate that this signal is either active low or that it becomes active at a falling edge Signal directions in signal mnemonics tables generally refer to the corresponding board or component in m
49. ptions Enabled Disabled Alternate ID Description Report alternate device ID MEN Mikro Elektronik GmbH 63 20F021P00 E4 2015 01 13 BIOS Options Enabled Disabled SATA Port 0 1 2 3 Hot Plug Description Enable disable Hot Plug Not supported on SATA ports 4 and 5 Options Enabled Disabled SATA Port 0 1 2 3 4 5 Spin Up Device Description Enable disable support of staggered spin up SSS Options Enabled Disabled SATA Port 0 1 2 3 4 5 Port Multiplier Description Enable disable support of port multiplier PMS Options Enabled Disabled Serial ATA Port 0 1 2 3 4 5 Description Not installed You can make no changes here MEN Mikro Elektronik GmbH 64 20F021P00 E4 2015 01 13 Thermal Configuration Sub menu gt Platform Thermal Configuration Shut Down Temperature Throttle on Temperature Shut Down Temperature BIOS 100 C CEC Description ACPI Active Trip Point the point at which the OS will shut down the system Options 70 C 80 C 90 C 110 C Throttle on Temperature 75 C 85 C 100 C 120 C Description Set the CPU temperature point of Throttle on Options 40 C 50 C 60 C 70 C 80 C 90 C MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 45 C 55 C 65 C 75 C 85 C BIOS Video Configuration Sub menu Primary Display Auto gt Internal Graphic Device Internal Graphic Device Auto IGD DVMT Pre Al located CSZ WIE IGD Gfx Low Power Mo
50. r Boot Exit TPM Status Not Installed TPM Operation No Operation Supervisor Password Installed Not Installed User Password Installed Not Installed Set Supervisor Password User Access level Set User Password Clear User Password F1 Help Power on password Disabled View Only N Select Item F5 F6 Change Values F9 Setup Defaults lt Select Menu Enter Select gt F10 Save and Exit Esc Exit Submenu TPM Status Description TPM Trusted Platform Module Status Not supported on the F21P Options Not installed TPM Operation Description TPM Trusted Platform Module Operation Not supported on the F21P Options No operation Supervisor Password Description Shows whether a supervisor password has been entered User Password Description Shows whether a user password has been entered MEN Mikro Elektronik GmbH 70 20F021P00 E4 2015 01 13 nae BIOS Set Supervisor Password Description Enter and confirm the supervisor password under this menu item To delete the password enter an empty password Power On Password Description Select when the password has to be entered Options Enabled The password has to be entered when the system starts Disabled The password has to be entered when changing to the setup menu User Access Level Description Set the User Access Level Options View Only Access to InsydeH2O Setup allowed but the fields cannot be changed Full Any field can
51. rt 3 PCIE2 TX PCIES RX in Differential pair of PCle receive lines port 3 PCIES RX optional can be implemented on a special board version instead of port 1 PCIE3_TX out Differential pair of PCle transmit lines port 3 PCIE3_TX PCIE_WAKE in Wake signal from PCle device to wake F21P from sleep state MEN Mikro Elektronik GmbH 44 20F021P00 E4 2015 01 13 Functional Description Signal Direction Function HD Audio HDA BIT CLK in out HD Audio serial data clock HDA RST out HD Audio reset HDA_SDIN in HD Audio serial data in HDA_SDOUT out HD Audio serial data out HDA_SYNC out HD Audio synchronization Digital DDPB_ x _n out Digital display interface B data differential pair Display DDPB x p Interface DDPC x n out Digital display interface C data differential pair DDP DDPC x p DDP CTRDATA in out Digital display interface control data DDP CTRLCLK in out Digital display interface control clock DDPC HPD in Digital display interface hot plug detect DPB OB AUX n in out Digital display interface auxiliary lines needed DPB OB AUX p when interface B is used as DisplayPort or shared with HDMI SDVOCTRL CLK and SDVOCTRL_DATA SDVOB_INT in Serial digital video input interrupt differential SDVOB_INT pair SDVO_FLDSTALL in Serial digital video field stall differential pair SDVO_FLDSTALL SDVO_TVCLKIN in Serial digital video TVOUT synchronizatio
52. s of USB front panel connectors 35 Signal mnemonics of Ethernet 10 100 1000Base T connectors 36 Pin assignment and status LEDs of 8 pin RJ45 Ethernet 10 100 1000Base T connectors LANI LAN2 00 cee eee 37 Pin assignment of 9 pin D Sub 10Base T 100Base TX plug connector LANTIGANI Ys va sorteren Sais Gar beden bet 37 Pin assignment of 114 pin side card connector pins 1 38 41 Pin assignment of 114 pin side card connector pins 39 76 42 Pin assignment of 114 pin side card connector pins 77 114 43 Signal mnemonics of 114 pin side card connector 44 Pin assignment of CompactPCI connector J2 re errisicviriuerresa 21 Signal mnemonics of CompactPCI connector J2 CompactPCI and CompactPCT PlusIO rear VO V ea she eerie teet were 52 Error codes signaled by board management controller via LED flashes 55 SMBUS de VIGBSu raar den orentis 55 Figures Figure 1 Figure 2 Figure 3 Figure 4 MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Map ot the board front VIEW 5st tee tmt e wed 20 Map of the board top VIEW ii sana sns assen hee ge 21 Position of battery on the mass storage adapter on the F21P 78 Labels giving the product s article number revision and Serial muinbet nst naden seine AE SUA wee a cina 81 19 Getting Started 1 Getting Started This chapter gives an overview of the board and some hints for first installation in a system
53. side card Simultaneous connection of two monitors I O e Ethernet 9 pin D Sub connector with one or two 10 100Base T ports instead of two RJ45 connectors Second Ethernet at rear I O connector J2 instead of one interface at the front e Rear I O VGA on CompactPCI J2 connector as an assembly option for the conduction cooled board version VBATT on CompactPCI J1 connector as an assembly option for the conduction cooled board version Miscellaneous TPM Trusted Platform Module chip assembled as an option Mechanical Side card can be added at left or right side of CPU MEN Mikro Elektronik GmbH 9 20F021P00 E4 2015 01 13 Configuration Options Operating Temperature Depends on system configuration CPU hard disk heat sink Maximum 85 C Minimum 40 C all processors Cooling Concept Also available with conduction cooling in MEN CCA frame Please note that some of these options may only be available for large volumes AS For more information on available standard versions see the online bef data sheet MEN Mikro Elektronik GmbH 10 20F021P00 E4 2015 01 13 Product Safety Product Safety Lithium Battery This board contains a lithium battery There is a danger of explosion if the battery is incorrectly replaced See Chapter 4 Maintenance on page 78 Electrostatic Discharge ESD devices Electrostatic discharge ESD can damage components To prote
54. sponsibility to any person whether a reader of the publication or not in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance whether wholly or partially on the whole or any part of the contents of the publication Conditions for Use Field of Application The correct function of MEN products in mission critical and life critical applications is limited to the environmental specification given for each product in the technical user manual The correct function of MEN products under extended environmental conditions is limited to the individual requirement specification and subsequent validation documents for each product for the applicable use case and has to be agreed upon in writing by MEN and the customer Should the customer purchase or use MEN products for any unintended or unauthorized application the customer shall indemnify and hold MEN and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim or personal injury or death associated with such unintended or unauthorized use even if such claim alleges that MEN was negligent regarding the design or manufacture of the part In no case is MEN liable for the correct function of the technical installation where MEN products are a part of Trademarks All products or services mentioned in
55. t aci orare go eroe seen ae 38 2 13 High Definition HD Audio Interface eee 39 2 14 Side Card Interface za vous ens chek bab weed ond cao doe RD ACE oe 40 2 14 1 Connection aas 225 400 oc ends cee heide 40 214 2 Installinp a Side Card icis eee rennteartentendte ni 46 2 15 PCI EXpI638 2 eot et meet herkend Rhe benk mie ek 49 MEN Mikro Elektronik GmbH 16 20F021P00 E4 2015 01 13 20F021P00 E4 2015 01 13 Contents 2 15 General samenst rtt REESE NR TRES 49 2 15 2 Implementation on E21D avs 22229 r9 ase 49 216 Compactl Cl Mtei Eon 23 0 1 ode atre gave ehfex dende 50 2 16 1 CompactPCI PluslO Rear UO os eo 50 2 162 CompactPCI Connector MI saar nversrermer snee 50 2 16 3 CompactPCI Connector J2 aa oan vaa one ane cae ce 50 2 16 4 Power Supply Status DEG FAILH 54 2 17 Reset Buttou nd Status LED savannen varta bidt 35 2 18 SMBus Devices iat dos arrestant nk 25 3 BIOS 656054555 edie Gee nnen einen snie T PREGA S Eq eM M qoi 56 AME PC TT 57 2 2 Advanced soa geo 9e REQUE hese sies 59 3 9 SEGUE zien cui dean aban ah potes Paru Odin oup aglow hagas 70 DA POWER oovcrsrdiedastaed ertsen Poe P orn rbd Ebor daa 72 3 9 BO0L s odd orate quid ep ae Riese bb mA dab N GEA 74 360 BRIE cca denn tt beed EEE AAD CERE CREE Na 76 3 61 Exit Saving Changes ua von mtrwse netheid hse 76 3 6 2 Save Change Without Exit 0 0c cece tamisa 76 3 6 3 Exit Discandms Changes ics seen sas sedens ns 76 36
56. t Sante RE NER ESSE TEE 25 2 Power SUPPLY coger cipes Sa d paite gra busted nn 25 2 2 Board SUDSEVISIOD sg d ud cis eot gu ta ot ca a bdo ee rd 23 2 3 Intel Active Management Technology AMT 26 2 4 Trusted Platform Module 42r RR saas cat aoe ond dan os 26 2 5 Reset Behavior and Power States aaneen 27 20 Real Time Clock atman open ehehe EE eka 27 2 7 Processor Core aans ananas Read Gead Rass PAR qr ET 27 2l Thermal Considerations ennen herman 28 2 8 MeImOPyuuio9o dum aud es a d gr EHE Ie deco itque cpabura dpa 28 2 8 1 DRAM System Memory an vaneen e 28 26 2 JBoObPlash 5 ugane bob pU tedere 28 2 0 Mass Storage uu i ee aee yeu RYE RO BEE CRY RR RES RS 29 2917 Seral ATA SATA errors seedemematide patat Soter 29 292 smicroSD Card xiousosas reris EREE TERECE 29 293 SATA DISK 5 sitter epe ttp indes ROSA 31 ZAO GEIDDNOS ren nse te a a aidan denied ee 33 2 10 1 VGA Front ContectiOn sas iu re Rr mi ete eee de 33 2102 VGA Rear Connection is vers vereiste diners 33 2 10 3 Connection via Digital Display Interface iL 34 2 M SB Intetfa6es Annatar neat pd awe ober het hota nale 35 ZILI Front Panel Connection ecri casas cag chon cada sande 35 211 2 Side Gard Connechon s 2 2 seiko ache anioe Eras 35 2 11 3 Rear I O Connection CompactPCI PlusIO 35 2 12 Ethernet Intetfaces cc sang net he e n et erve ars ET TR Res 36 2121 Front Panel Connection og ese bere pO REPE ORA 36 2 122 Rear VO Connec
57. ter card in the heat sink area which is assembled by standard See Chapter 2 9 1 Serial ATA SATA for details on the Serial ATA interface Chapter 2 9 3 mSATA Disk for details on the mSATA interface and also Chapter 2 9 2 microSD Card for more information on the microSD card 2 9 1 Serial ATA SATA The serial ATA SATA interface is controlled by the platform controller hub and provides six SATA channels In compliance with the CompactPCI PlusIO standard PICMG 2 30 four of these interfaces are led to the J2 rear I O connector One SATA channel is led to the side card connector The device can be connected through the use of a side card The sixth channel is used for the mSATA disk Four interfaces are compliant to SATA revision 2 x 3 0 Gb s Two of the interfaces on the J2 rear I O connector are compliant to SATA revision 3 x 6 0 Gb s The interfaces can be run in AHCI and RAID mode RAID 0 1 5 and 10 are supported See Chapter 2 14 Side Card Interface on page 40 for details on the side card interface and also Chapter 2 16 1 CompactPCI PluslO Rear I O on page 50 for details on the rear I O 2 9 2 microSD Card The F21P provides an onboard microSD card slot on the bottom side of the mSATA adapter card in the heat sink area The slot is ready to use The F21P is shipped without a microSD card installed d See MEN s website for ordering options MEN Mikro Elektronik GmbH 29 20F021P00 E4 201
58. ts in a data rate of max 250 MB s per lane in each direction The standard PCI bus with 32 bits 33 MHz only allows a maximum of 133 MB s If you use only one lane you speak of a PCIe x1 link You can couple several lanes to increase the data rate e g x2 with 2 lanes up to a x32 link using 32 lanes In addition PCIe supports hot plug for instance to exchange defect expansion boards during operation In terms of software most operating systems can handle PCI Express boards just as well as the old PCI 2 15 2 Implementation on F21P On F21P the three Gigabit Ethernet channels are permanently connected via PCle x1 links Another three x1 links are available for use over a side card This means that the side card implementation determines the usage of these three links Four PCIe x1 links are led to the J2 rear I O connector in compliance with the CompactPCI PlusIO standard PICMG 2 30 The interfaces on the J2 connector and the side card connector support the PCI Express specification 2 x with a data transfer rate of 5 Gbits s per lane MEN Mikro Elektronik GmbH 49 20F021P00 E4 2015 01 13 Functional Description 2 16 CompactPCI Interface The F21P is a 3U CompactPCI system slot board It implements a 32 bit PCI interface to the CompactPCI backplane which uses a 3 3 V signaling voltage It also tolerates 5 V The CompactPCI bus connects to the processor via a PCI Express to PCI Bridge The board supports seven external PC
59. turers Group PICMG QE Introduction to CompactPCI PluslO on Wikipedia MEN Mikro Elektronik GmbH 80 20F021P00 E4 2015 01 13 Appendix 5 2 Finding out the Product s Article Number Revision and Serial Number MEN user documentation may describe several different models and or design revisions of the F21P You can find information on the article number the design revision and the serial number on a label attached to the board Article number Gives the product s family and model This is also MEN s ordering number To be complete it must have 9 characters Revision number Gives the design revision of the product Serial number Unique identification assigned during production If you need support you should communicate these numbers to MEN Figure 4 Labels giving the product s article number revision and serial number man Madein Article No Rev No O un poem Germany 02F022P00 00 00 00 a 641517 Complete article number Revision number Serial number MEN Mikro Elektronik GmbH 81 20F021P00 E4 2015 01 13
60. unctional Description F E D C B A Z 22 GND GAO GAT GA2 GA3 GA4 GND 21 GND GND 20 GND GND 19 GND GND 18 GND GND 17 GND GNT6 REQ6 PBRST GND 16 GND ei GND DEG 2 PE CLK 4 PE CLK GND 15 GND GNT54 REQS FAIL 2 PE CLK 4 PE CLK GND 14 GND PWRBTN amp SATA SCL 4 PE CLKE amp 1 PE CLK 3 PE CLK GND 13 GND SATA SL SATA SDO 3 PE CLKE 1 PE CLK 3 PE CLK GND 12 GND 4 SATA Rx SATA SDI 2 PE CLKE amp 1 PE CLKE amp 4 PE Rx00 GND 11 GND 4 SATA R 4 SATA Tx 4 US 4 PE Tx00 4 PE_Rx00 GND 10 GND 3 SATA Rx 4 SATA Tx 4 PE Tx00 3 PE Rx00 GND 9 GND 3 SATA Rx 3 SATA Tx 3 PE Tx00 3 PE RxO0 GND 8 GND 2 SATA Rx 3 SATA Tx 3 PE Tx00 2 PE_Rx00 GND 7 GND 2 SATA Rx 2 SATA Tx 2 PE Tx00 2 PE_Rx00 GND 6 GND 1 SATA Rx 2 SATA Tx 2 PE Tx00 1 PE Rx00 GND 5 GND 1 SATA Rx 1 SATA Tx 1 PE Tx00 1 PE Rx00 GND 4 GND perdon 1 SATA Tx 1PE Tx0 VIO GND 3 GND GNTA4 amp REQ4 GNT3 GND CLK4 GND 2 GND REQ3 GNT2 f CLK3 CLK2 GND 1 GND REQ2 GNT1 REQ1 GND CLK1 GND Note SATA ports 3 and 4 support SATA revision 3 x 6 0 Gb s The second Ether net interface marked in gray can be implemented as an option on a special board version MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 Functional Description Table 14 S
61. wing error messages Table 15 Error codes signaled by board management controller via LED flashes Number of Error Description Flashes 0 CPUBCI ERR NONE No error 1 CPUBCI ERR 33V 3 3 V failure 2 CPUBCI ERR INP Input voltage failure 3 CPUBCI ERR NO EXT PWR OK External power supply failure 4 CPUBCI ERR CPU TOO HOT CPU temperature too high 5 CPUBCI ERR BIOS TIMEOUT BIOS startup failure gt 5 Internal error 2 18 SMBus Devices Table 16 SMBus devices Address Function Ox9A Ox9B Board controller OxA0 Memory channel A 0x60 Protected register 0x30 Temperature sensor A OxA4 Memory channel B 0x64 Protected register 0x34 Temperature sensor B OxAE Board EEPROM Ox6E Protected register Ox3E Temperature sensor B 1 The first address is for write command the second for read command MEN Mikro Elektronik GmbH 20F021P00 E4 2015 01 13 BIOS The F21P is equipped with an InsydeH2O setup utility from Insyde Software InsydeH2O is Insyde Software s firmware product line designed to replace traditional PC BIOS It is an implementation of the Intel s Platform Innovation Framework for UEFI EFI The UEFI EFI specification defines a new model for the interface between operating systems and platform firmware This interface consists of data tables that contain platform related information plus boot and runtime service calls that are available to the operatin
62. y to lead a display data channel to the backplane via the J1 CompactPCI connector MEN Mikro Elektronik GmbH 33 20F021P00 E4 2015 01 13 Functional Description 2 10 3 Connection via Digital Display Interface The F21P provides two digital display interfaces on the side card connector One supports SDVO DisplayPort and HDMI the other only DisplayPort and HDMI Embedded audio is also supported on DisplayPort and HDMI One DVI interface can be implemented using the SDVO interface on an MEN side card See Chapter 2 14 Side Card Interface on page 40 for further details on the side card interface D See MEN s website for available side cards For possibilities to E implement DisplayPort or HDMI using a side card please contact MEN s sales team MEN Mikro Elektronik GmbH 34 20F021P00 E4 2015 01 13 Functional Description 2 11 USB Interfaces The F21P provides eleven USB 2 0 ports controlled by the chipset Two USB interfaces are routed to standard front panel connectors four are led to the side card connector and another four can be accessed on the CompactPCI J2 rear I O connector compliant to the CompactPCI PlusIO standard The remaining interface is used for connection of the microSD card The USB interfaces support UHCI 2 11 1 Front Panel Connection Two USB interfaces are accessible at the front panel Connector types 4 pin USB Series A receptacle according to Universal Serial Bus Spec

2nAxxxxyy Ez User Manual - Diamond Point International

Contents

Download Pdf Manuals

Related Search

Related Contents