User Manual - Perfect Light Nederland
Contents
1. music or auto ELECTRICAL ais Saadeh dod ee Gata nate AAA 3 prong IEC male socket AC Power switch selectable operating ranges 115 120 V 220 240 V 50 60 Hz Manii ii ane bel teen a Meese KER UA ees 2 AT time delay TYPICAL POWER AND CURRENT 120 V A WAA AAA E wise taal 115 W 1 0 A 120 V GOs FIZ a se ee een gi eher la ann Ben 113 W 0 9 A 200 VEZ a a ee 106 W 0 5A 230 DD HZ Een a Goh nS BE Alay abate Oe ac ats 105 W 0 5A ZION D are ee een seydi ikti nie A dl 114 W 0 5 A 240 V SIO wa Tonei eieaa a a nen an de rent 113 W 0 5 A INCLUDED ITEMS US VERSION 2 m 6 5 ft US mains cable 18AWG with US male connector UL approved Philips 12V EFP 8H 100W lamp User manual Specifications 19 20 INCLUDED ITEMS NON US VERSION 3 m 9 8 ft EU mains cable 3x1 Omm with Schuko male connector 3 m 9 8 ft EU mains cable 3x1 Omm with no male connector Philips 12V EFP 8H 100W lamp User manual ACCESSORIES Philipps12VEFP 8H100Wlamp P N 97000004 Half coupler clamp P N 91602005 Fuse ZAM a e n a N en M P N 05020009 ORDERING INFORMATION Mania EF1i US version P N 90430003 Mania EF1i non US version P N 90430002 Mania EF Ii user manual y Martin www martin dk e Olof Palmes Alle 18 e 8200 Aarhus N e Denmark Tel 45 8740 0000 e Fax 45 8740 00102. OVERHEAD MOUNTING The Mania EF1i is designed to be hung overhead with a clamp not included Block access below the work area before proceeding Mania EFli user manual Always use a secure means of secondary attachment For indoors use only To hang the Mania EF1i on an overhead support 1 Verify that the structure can support at least 10 times the weight of all installed fixtures clamps cables auxiliary equipment and other items 2 If hanging the fixture with a rigging clamp verify that the clamp is undamaged and is designed for the fixture s weight Bolt the clamp securely to the mounting bracket on the fixture with a grade 8 8 minimum M12 bolt and lock nut or as recommended by the clamp manufacturer through the clamp hole in the mounting bracket 3 If permanently installing the fixture verify that the hardware not included and mounting surface can bear at least 10 times the fixture s weight 4 Working from a stable platform clamp or fasten the fixture to the structure 5 Install a safety cable that can hold at least 10 times the weight of the fixture through the safety cable attachment point on the fixture 6 Loosen the swivel locks tilt the fixture to the desired angle and retighten Swivel locks Safety cable attachment point WOW 7 Verify that the fixture is at least 1 meters 3 3 ft from the surface to be illuminated and at least 0 3 meters 1 ft from any combustible ma
3. or severe injury due to fire and heat electric shock and falls Read this manual before powering or installing the fixture follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture If you have questions about how to operate the fixture safely please contact a Martin distributor for assistance Refer any service operation not described in this manual to a qualified technician Do not modify the fixture or install other than genuine Martin accessories and upgrade kits Refer servicing to qualified personnel Maximum ambient temperature T 40 C 104 F See serial label for replacement fuse size and lamp type Suitable for mounting on normally flammable surfaces Do not look directly into the light Risk of fire electrical shock and burns Use only in dry locations For indoors use only Do NOT block exhaust vents Mania EF Ii user manual Shields lenses or ultraviolet screens shall be changed if they become visibly damaged to the extent that their effectiveness is impaired for example by cracks or deep scratches The lamp shall be changed if it becomes damaged or thermally deformed If the external power cord of this luminaire is damaged it shall be replaced by a special cord exclusively available from your Martin dealer Avoiding electric shocks Warning Always disconnect from mains power before replacing the lamp fuses or any part and when not in use Bef
4. switch selectable power supply that can operate in the following voltage ranges at 50 60 Hz 115 120 volts setting 115 220 240 volts setting 230 Warning Do not operate the fixture on a power supply that falls outside of these ranges Select the operating range using the red AC supply switch at the rear of the fixture LSS AC supply setting Installation Installing a plug on the mains lead Warning Important Warning For protection from dangerous electric shock the fixture must be grounded earthed The AC mains supply shall have overload and ground fault protection Verify that the feed cables are undamaged and rated for the current requirements of all connected devices before use The fixture s mains lead may require a grounding type cord cap that fits your power distribution cable or outlet Consult a qualified electrician if you have any doubts about proper installation Following the cord cap manufacturer s instructions connect the appropriate wires to ground earth live and neutral The following table below shows some common wire identification schemes Function Wire EU Wire US live brown black neutral blue white ground yellow green green Applying power Connect the mains power cable to the fixture at the 3 prong IEC male input socket at the rear of the fixture 4 MICH Mains socket Power on switch Turn the lamp on using the power on switch
5. Mania EF1i user manual y Martin Measurements are expressed in millimeters 2003 Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark Printed in China P N 35000142 Rev A Introduction 4 Sa ico a rra adas AAA 4 UNPACKING eb A dnd 6 Mania EF1i overview x e e een 6 Installation AA yeminle Ai 7 AGC BOWEr UA AA AAA aad do NE 7 Overhead mounting TTT 8 Operation oces rarene ar 10 Setting the trig mode AINA WAWA IA AAA 10 The gobo Wheel IA a aa anna en 11 Focusing the Mania EFTE 12 Basic Service oi A sh 13 Cleaning lama cocinada eee bee eee GA be pee Ha apd 13 Lamp maintenance 14 MAINS US aos se ate e Rene Peer a de i 16 Troubleshooting 18 Specifications IAA 19 INTRODUCTION Warning Thank you for selecting a Martin Mania EF1i The Mania EF1i is a pre programmed music activated DJ effect with a motorized rotating mirrored reflector and a motorized rotating wheel with 8 static gobos gobos are outlines or masks placed in a light beam to create different patterns SAFETY INFORMATION This product is not for household use It presents risks of lethal
6. an cause burns and eye damage Introduction 5 Preventing injuries due to falls gt When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices e Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Block access below the work area whenever installing or removing the fixture UNPACKING The packing material is carefully designed to protect the fixture during shipment always use it to transport the fixture The Mania EF1i comes with the following e 3 wire IEC power cable e User manual MANIA EF1i OVERVIEW Mounting bracket Swivel locks Safety wire attachment AC supply setting LS 8 Gobo wheel rotation switch Fuse holder Y Z Thumb screw cover lock Mains socket Power on switch 6 Mania EFli user manual INSTALLATION AC POWER Before operation ensure that factory setting of voltage and freguency match local power supply Always ground earth the fixture electrically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Note If the external power cord of this luminaire is damaged it shall be replaced by a special cord exclusively available from your Martin dealer Configuring for local mains power The Mania EF1i has a
7. e thumb screw holding the cover in place e Thumb screw 3 Slide the fixture cover open as far as possible there is a physical stop point that prevents access to the power supply section 4 Grasp the oldlamp by the reflector and slide it carefully out of the lamp holder Basic service 15 5 Pull the socket off the lamp Do not pull the wires 6 Push the socket fully onto the pins of the new lamp 7 Clean the glass bulb and reflector with a cloth particularly if your fingers touched the glass A clean lint free cloth wetted with alcohol is best 8 Gently push the lamp into the holder until it snaps into place 9 Close the fixture cover and tighten the thumb screw MAINS FUSE The Mania EF1i uses a time delay fuse for protection against current overload An indication that the fuse may have blown is that when power is applied and the lamp is switched on no light is produced If the fuse blows repeatedly there is a fault with the unit that requires service by a Martin technician Never bypass the fuse or replace it with one of another size or rating Replacing the main fuse 1 Unplug the mains cable from the input socket 16 Mania EFli user manual 2 Pry open the fuse holder located next to the mains power connector with a flat head screwdriver and remove the fuse Fuse holder 3 Replace the fuse with one of the same type The fuse rating is listed on the serial number label and in Spec
8. ifications on page 19 4 Replace the fuse holder Basic service 17 TROUBLESHOOTING problem probable cause s suggested remedy No light No power to the fixture Check connections Blown fuse If power is applied and the lamp is switched on but does not light then check and replace fuse if necessary Burned out lamp Install new lamp Fixture to hot Allow to cool Improve air flow around fixture No action Sound too low to activate Increase volume control circuit Move speakers closer Electrical malfunction Refer to a Martin service technician Fuse blows repeatedly Electrical malfunction Refer to a Martin service technician 18 Mania EFli user manual SPECIFICATIONS PHYSICAL Size without mounting bracket LxWxH 312 x 250 x 142mm 12 3 x 9 8 x 14 2in NV GION en en et 6 5 kg 14 31b CONSTRUCTION HOUSING yek eee eee ee eee ees steel and aluminum THERMAL Exterior surface temperature under steady state condition 100 C 212 F Time required to cool before handling at least 20 minutes Maximumambienttemperature T 40 C 104 F INSTALLATION Minimum distance to flammable material 0 3 m 1ft Minimum distance to illuminated surface 1 0 m 3 3ft Minimum clearance around air vents 0 1 m 4in CONTROL AND PROGRAMMING Stand alone triggers
9. nd allow it to cool for 20 minutes Basic service 13 2 Remove the thumb screw holding the cover in place Thumb screw 3 Slide the fixture cover open as far as possible there is a physical stop point that prevents access to the power supply section 4 Vacuum or gently blow away dust and loose particles with compressed air 5 Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water Do not rub the surface lift the particles off with a soft repeated press 6 Remove smoke and other residues with cotton swabs or unscented tissues moistened with isopropyl alcohol A commercial glass cleaner may be used but residues must be removed with distilled water Clean with a slow circular motion from center to edge Dry with a clean soft and lint free cloth or compressed air 7 Close the fixture cover and tighten the thumb screw taking care not to trap any loose wires LAMP MAINTENANCE Warning Isolate electrically before re lamping The lamp shall be changed if it becomes damaged or thermally deformed 14 Mania EFli user manual Caution Hot lamp Only the Philips 12V EFP 8H 100W type No 6834 lamp is supported Martin P N 97000004 These lamps normally last for 800 hours of operation Warning Installing any other lamp may damage the fixture Installing a lamp in the Mania EF1i 1 Disconnect the fixture from power and allow it to cool for 20 minutes 2 Remove th
10. ns This is easiest to do in Music Trig mode while no music is being played Pull the mechanism out or push it in until a sharp image is acquired O Sy ML oa e Mania EFli user manual BASIC SERVICE Warning Important This chapter describes the maintenance procedures that you can perform yourself The exterior of the fixture can become hot Always disconnect the fixture from AC power and allow to cool for at least 20 minutes before handling or opening CLEANING Regular cleaning of the elements in the optical path as well as the air vents is vital to maintaining the operational quality of the Mania EF1i Excessive dust smoke fluid and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty Cleaning the air vents To maintain adequate cooling dust must be cleaned from the air vents periodically Remove dust from the air vents with a soft brush cotton swab vacuum or compressed air Cleaning optical components Clean the optical components regularly The presence of smudges or dust on optical surfaces can reduce the strength of the light output and the quality of the effects Use care when cleaning optical components and work in a clean well lit area The coated surfaces are fragile and easily scratched Do not use solvents that can damage plastic or painted surfaces 1 Disconnect the fixture from power a
11. ore operation ensure that factory setting of voltage and frequency match local power supply Always ground earth the fixture electrically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the fixture to rain or moisture Never operate the fixture with missing or damaged lenses and or covers Protecting yourself and others from burns and fire Warning Hot lamp The exterior of the fixture can become hot Allow to cool for at least 20 minutes before handling or opening Surface temperature under steady state condition 100 C 212 F Minimum distance to flammable material 0 3 m 1 ft Minimum distance to illuminated surface 1 0 m 3 3 ft Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating Ensure that the air flow through vents is free and unobstructed Provide a minimum clearance of 0 1 meters 4 inches around air vents Never place filters or other materials over the lens or in the optical path The exterior of the fixture can become hot Allow the fixture to cool for at least 20 minutes before handling Do not operate the fixture if the ambient temperature T exceeds 40 C 104 F Do not stare directly into the light Never operate the fixture without all lenses and covers installed an unshielded lamp emits dangerous UV radiation that c
12. terials Verify that the clearance around the air vents is at least 0 1 meters 4 in Installation OPERATION 10 The lamp will light when the power on switch at the back of the fixture is turned on To achieve optimal results the use of smoke effects together with your Mania EF 1i is recommended SETTING THE TRIG MODE Use the switch on the back of the fixture to set it to Auto or Music trig mode OE g MICH Trigger mode switch Power on switch In Auto Trig mode trigger signals are generated randomly This will result in unsynchronized operation that is not in time with music Music Trig mode the built in microphone will generate trigger signals as a result of sounds that it picks up This will result in synchronous effects in time with any music that is being played Mania EFli user manual THE GOBO WHEEL The Mania EF1i contains the following gobo wheel Gobo wheel rotation is activated and deactivated using the gobo wheel rotation switch The wheel will stop when the switch is set to O In Auto trig mode the wheel will rotate when switch is in position I or Il In Music trig mode the wheel will react to the beat of the music in position Il or will spin continuously in position I _ Gobo wheel rotation switch Note that it is the whole wheel and not the individual gobos that rotates Operation 11 12 FOCUSING THE MANIA EF1I The focus is adjusted using the mechanism next to the le
Download Pdf Manuals
Related Search