User Manual Model: GoIP - Discovery Telecom Technologies
Contents
1. One Chunnel GSM VoIP Gateway provider for more information 3 4 5 2 Media NAT Traversal A B C D Similar to Signaling NAT Traversal this feature allows media packets RTP to be routed properly in various network environments Media NAT Traversal None STUN RFC 3489 Portforward D MZ Relay Proxy None Select None to disable this feature STUN RFC 3489 STUN Simple Traversal of UDP User Datagram Protocol through NATs Network Address Translators is a network protocol allowing a client behind a NAT or multiple NATs to find out its public address the type of NAT it is behind and the internet side port associated by the NAT with a particular local port Select STUN RFC 3489 to use a STUN server for Signaling NAT Traversal Enter the IP Address or the domain name of the STUN server to be used Port forwarding Support Port forwarding sometimes referred to as tunneling is the act of forwarding a network port from one network node to another This technique can allow an external user to reach a port on a private IP address inside a LAN from the outside via a NAT enabled router In order for this feature to work the local network Gateway must support this feature and be set up properly Please consult your network administrator for help to enable this Port forwarding feature Relay Proxy Relay proxy is a proprietary NAT traversal technology Please consult your service provider for more information2. If you want obtained LAN port IP by sending a SMS message please send INFO or info lf a local DHCP host is not available you can then access the GolP Gateway via the PC port You will need to change the PC LAN configuration via the Network Connections under the Control Panel Windows Control Panel gt Network Connections gt Local Connectionism s Property gt TCP IP Protocol s Property Internet Protocol TCP IP Properties PT General ou can get IP settings assigned automatically if your network supports this capability Uthenwise vou need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address CE 10 Subnet mask 255 255 255 q Default gateway Set an unused IP address that is in the same segment as the PC port address Once either the IP address of the LAN or PC port is known you are now ready to access the Web server of GolP Gateway 3 1 Web Configuration Menu If your PC is connected to the GolP Gateway via the LAN port network segment you need to type the LAN IP address of the GolP Gateway in your Web Browser to access the Web server of the GolP Gateway If not you should type the PC IP address 192 168 8 1 in 9 One Chunnel GSM VoIP Gateway the Web Browser e agenten fold rani ferosote tersa lores File Edit View Favorites Tools Help eo gt gt e al en uC Search 2 Favo
3. user The default password is 1234 This user name is limited to access the Network Configuration menu B Administrator Password default admin This is the password for the user name ID admin The default password is admin This user name allows full access to all configuration settings available 3 13 3 Reset Configuration Click on the Reset Config tab to reset the GolP Gateway to its factory default settings 3 13 4 Reboot the Device Click on the Reboot tab to reboot the GolP Gateway 44 One Chunnel GSM VoIP Gateway 4 Hardware Specifications Processor ARM9E 133MHz ET CCOO COS CECI COS EA CT S GSM Module Type E ETE O LT NC Working Humidity 40 90 Not Congealed nn CC EEN feowsmrs CO voro CO 5 Manufactory Parameters a DHCP Auto Obtain Network pc Bate IP 192 168 8 1 pc Bale Server Running admin admin Password user 1234 Note This default parameter are unsuitability the customization s products 45
4. Currently the following 3 kinds of packaging mechanism are supported gt Mode 1 The media uses UDP packets and or encrypt with multiple UDP port gt Mode 2 The media uses UDP packets and or encrypt with single UDP port gt Mode 3 The media uses TCP packets and or encrypt UDP over TCP 2 One Chunnel GSM VoIP Gateway Media NAT Traversal Password fs Len cryption Relay Mode O10203 3 5 Call Divert The Call divert feature controls the routing of calls between VolP and GSM Call Divert Forward to PSTN Enable Disable eel orward Fai PSTN Forward Fail Drop The Call VoIP To PSTN Kies le E VoIP To PSTN rt A PSTN Forward to VolP Enable Disable a AA PSTN To VoIP Forward Password po PSTN To VoIP TA VolP 3 5 1 Call Forward From VolP To PSTN Call Divert Forward to PSTN Enable Disable ene A A all Drop The VOIP To PSTN PSTN Forward Fail Drop The Call Forward Password Po VoIP To PSTN a AAA PSTN Forward Number Enter this field to forward all incoming VoIP calls to this number PSTN or Mobile Using to add a 500ms delay to the dialing sequence If this field is blank calls will not be forwarded The GolP Gateway answers an incoming VoIP call and generates a dial tone The caller can then dial a number PSTN or Mobile desired Please see below if the 28 One Chunnel GSM VoIP Gateway You can select a disposal method for PSTN forward f
5. Subnet Mask 255 255 255 0 DHCP Server Enable Disable Starting Address 192168 8 150 Ending Address 192 168 858 200 Static DNS optiona 7 Advanced 1 Bridge Mode 4 2 4 One Chunnel GSM VoIP Gateway Select Bridge mode if your network topology requires the network devices PC or others to be in the same network segment as the GolP Gateway In this case the GolP Gateway functions as an Ethernet Switch Static IP Mode Default Setting Select Static IP mode for a new network segment for the network devices behind the GolP Gateway In this case the GolP Gateway functions as an Ethernet Router Fill in the IP Address field with a new segment address that is different from that for the LAN port Please select the Subnet Mask accordingly A commonly used value is 255 255 255 0 PC Port Static IP D IP Address Subnetmask ___ DHCP Server O Enable Y Disable Enable the DHCP Server if you want the GolP Gateway functions as a local DHCP host for the PC segment This will enables the GolP Gateway to assign IP Addresses to network devices that are attached to the PC port segment DHCP Server Enable Disable Starting Address Ending Address Static DNStoptional Specify the Starting Address Ending Address and Static DNS accordingly Advanced The Advanced settings allow the user to set the broadcast address and to clone a MAC address instead of using the factory preset MAC address Please
6. Call Settings Endpoint Type H 323 Phone Endpoint Mode Gatekeeper Mode Phone Number GateWay Prefix Display Name H 323 ID Gatekeeper Address Ili C Enable VOS AVS signaling Encryption Enable Authentication 3 4 1 3 Advance Settings Click Advance Settings to access additional H 323 parameters as shown below Advanced Settings lt lt RAS Port Fast Start Enable Disable Register Mode DTMF Signaling Signaling QoS Signaling NAT Traversal L A RAS Port RAS Port is an unreliable channel which is used to convey the registration admissions bandwidth change and status messages between two H 323 entities B Q 931 Port Call Signaling Port Call Signaling Port is a reliable channel which is used to convey the call setup and release messages between two H 323 endpoints C gt H 245 Port Media Control Ports Media control port is the port or port range used by the H 245 media control protocol 19 One Chunnel GSM VoIP Gateway D Fast Start E F Enable or disable the Fast Start in H 225 0 Most H 323 terminals or Gateways support the Fast Start feature Register Mode Register Mode Register Multiple Mur Fe gister Multiple Murmbe Register Multiple Times Register Multiple Numbers The GolP Gateway sends registration request in one signaling packet to the gatekeeper In the mode one signaling packet includes two VoIP line s registration information Register Mul
7. ID in SIP invitee s Caller ID option and Remote Party ID option 36 One Chunnel GSM VoIP Gateway Sending Message to 192 168 2 1 5060 INVITE sip 5000 192 168 2 1 5060 transportudp SIP 2 0 Via SIP 2 0 UDP 192 168 2 180 5060 branch 29hG4bK 1450498491 From 13800000000 lt sip 13800000000 192 168 2 1 5060 gt tag 232569343 To lt sip 5000 4192 168 2 1 gt Call ID 18530689860192 168 2 180 CSeq 2 INVITE Contact lt sip 1382000000004192 168 2 180 5060 gt Max Forwards 30 User Agent HBT Remote Party ID 13800000000 lt sip 1380000000000192 168 2 1 gt party calling screen no privacy offe Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY REFER REGISTER MESSAGE INFO SUBSCRIBE Content Type applications dp Content Length 226 About H 323 s PSTN Caller ID transmit we will perfect it in later firmware 3 8 Dail Plan Dial Plan defines how a number VoIP is processed when GolP receives it This field is located in the Calling Setting Window and it is available for both H 323 Phone and SIP Phone The Dial Plan is very flexible and can be configured for a wide range of dialing applications Call Divert Forward to PSTN Enable Disable ea O VoIP To PSTN e LA VoIP To PSTH Forward to VolP Enable Disable o AAN PSTN To VoIP a ll PSTN To VoIP AAN VolP The basic syntax is lt event gt lt action gt lt event gt lt action gt where lt event gt
8. consult your network administrator for further information Advance lt lO Address ee Address 3 11 Save Configuration To confirm and commit all changes made click on the Save Changes tab Otherwise all changes will be discarded Once all changes are saved the following screen message is displayed 42 One Chunnel GSM VoIP Gateway gt Configuration saved 3 12 Discard Changes To discard all changes made click on the Discard Changes tab 3 13 Tools Menu Select the Tools to access the following functions Online Upgrade Change Password Reset Config and Reboot in Configurations Last Upgrade Time Current Version GH5 3 01 Tools Online Upgrade Change Password keset config Reboot 3 13 1 Online Upgrade To perform a firmware upgrade select the Online Upgrade tab to access the page below Online Upgrade Last Upgrade Time Current Version GH5 3 01 Enter the update link as provided by your service provider A sample link is 43 One Chunnel GSM VoIP Gateway Click the Start button to start the firmware upgrade WARNING POWER SHUTDOWN FAILURE DURING FIRMWARE UPGRADE MAY PERMINENTLY DAMAGE THE GOIP GATEWAY 3 13 2 Change Password Click on the Change Password tab to access the page below New Password Confirm Password fs Change Administration Level New Password i Confirm Password Change A User Password This is the password for the user name ID
9. version of the Gateway such as GHS 3 01 5 C Hardware Mode This field shows terminals hardware type D Phone Status This field shows the status of Line s connection status If the connection is successful this field displays LOGIN otherwise it displays LOGOUT 3 2 2 Network Information A LAN Port Configuration This field displays the status of the LAN port B PC Port Configuration This field displays the status of the LAN port C PPPoE lf PPPoE is enabled it displays its status D Default Route This field displays the IP address of the default routing Gateway E DNS Server This field displays the IP address of the Domain Name Server 11 One Chunnel GSM VoIP Gateway 3 2 3 GSM Module Information A GSM Module This field displays the GSM module type B GSM Signal This field displays the GSM signal status C GSM Status This field shows the status of GSM connection status If the connection is successful this field displays LOGIN otherwise it displays LOGOUT 3 3 Configurations Click on the Configurations tab on the left hand column to access the device configuration menu Preference Network Call Settings Call Divert Save Changes and Discard Changes Status ze E Language 5 dp ir sw Network Tones China Configurations Time Zone CMT o GSM Group Mode Disable v A Time Server pool ntp org O Ea Time Gap Network Auto provision O Enable Disable Call settings Network Configurat
10. 2 89 CSeq 3 MESSAGE Contact lt sip 3999 192 168 2 89 gt max forwards 16 date Tue 18 Nov 2008 06 36 37 GMT user agent SIPPER for 3CX Phone p hint usrloc applied Content Type text plain Content Length 26 13682626800 Hello world The GolP will send a SMS to GSM number 13682626800 the SMS content is Hello world 3 7 PSTN Caller ID Transparent In SIP protocol GolP support PSTN Caller ID transparent to VoIP via SIP Invite signaling 35 One Chunnel GSM VoIP Gateway SMS Mode Disable PSTN Forward Fail CID Forward Mode Use Remote Party ID Use CID as SIP Caller IC Disable Disable PSTN Caller ID transparent to VoIP Use Remote Party ID GolP add Caller ID in SIP invite s Remote Party ID option sending Message to 192 168 2 1 5060 INVITE sip 50000192 168 2 1 5060 transport udp SIP 2 0 Via SIP 2 0 UDP 192 168 2 180 5060 branch 79h64bK1645487913 From lt sip 200010192 168 2 1 5060 gt user phone tag 406202416 To lt sip 5000 1192 168 2 1 gt Call ID 8472302780192 168 2 180 CSeq 2 INVITE Contact lt sip 20000192 168 2 180 5060 gt Max F orwards 30 User Agent HBT Remote Party ID 13800000000 lt sip 13800000000 192 168 2 1 gt party calling scre n no privacy off Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY REFER REGISTER MESSAGE INFO SUBSCRIBE Content Type application s dp Content Length 226 Use CID as SIP Caller ID GolP use PSTN Caller
11. 2121234 actual number dialed 82121234 3 Dial Plan 001 001 1751 means that the number dialed out will the first 3 digits O01 changed to 1751 when a number with the first digits as O01 is entered a Number entered 00182121234 actual number dialed 175282121234 b Number entered 82121234 actual number dialed 82121234 4 Dial Plan XXXX means that the input number is limited to 4 digit long and will be dialed out immediately when the fourth digit is entered 5 Dial Plan 18XXXXXXXXX 0 means that the input number is restricted to 11 digit long and the first two digits must be 13 When this condition is matched the number dialed out will have a leading 0 added a Number entered 13901234567 actual number dialed 013901234567 b Number entered 12801234567 actual number dialed 12801234567 6 Dial Plan 13 6 9 XXXXXXXX 0 means that the input number is restricted to 11 digit long and the first two digits must be 13 and the third digit can be 6 7 8 or 9 When this condition is matched the number dialed out will have a leading O added a Number entered 13901234567 actual number dialed 013971234567 38 One Chunnel GSM VoIP Gateway b Number entered 13001234567 actual number dialed 13001234567 Please note that the above samples are simple and intended to sh
12. EFER REGISTER MESSAGE INFO SUBSCRIBE Content Type application sdp Content Length 226 Use can add a SMS prefix with mode 3 it will work like mode 1 3 6 2 SMS Relay GolP GSM gateway supported SMS relay SMS Mode a eel Humber The SMS Forward Number is the receiver of your VolP system it will receive the SMS send from GolP when some GSM phones send a SMS to GolP 3 6 2 1 SMS Relay To VolP System When GolP receive a SMS come from GSM network it will auto relay to VoIP system s appointed number SMS Forward Number Suppose the SMS Forward Number is 3999 and SMS sender number is 8613682626865 the SMS content is 075583185700 The GolP will send a message to your VoIP system like follow 34 One Chunnel GSM VoIP Gateway MESSAGE sip 3999 192 168 2 1 SIP 2 0 Via SIP 2 0 UDP 192 168 2 162 5060 branch z9hG4bK 1967685528 From lt sip 1638 192 168 2 1 gt tag 66 7435 95 To lt sip 3999 192 168 2 1 gt Call ID 2094144847 192 168 2 162 CSeq 4 MESSAGE Contact lt sip 1638 192 168 2 162 5060 gt Max Forwards 30 User Agent HyberTone Content Type text plain Content Length 28 8613682626865 075583185700 3 6 2 2 SMS Relay To GSM Network When GolP receive a message come from SIP server as follow MESSAGE sip 1638 192 168 2 162 5060 SIP 2 0 From lt sip 3999 0192 168 2 89 gt tag 5031 To lt sip 16380192 168 2 1 gt Call ID 808807EB 48B3 DD11 BB46 005056C00008 192 168
13. Mode Default Voice Pp Gateway Media Settings gt gt A H 323 Phone Number H 323 phone number fill the login number E164 here B Display Name Display name is the name to be displayed on the called VoIP party C H 323 ID If the system requires an H 323 ID as a method of Authentication enter the H 323 ID provided D Default Voice Gateway This field assigns the IP address or the domain name of the gatekeeper or other VoIP gateway The port number can be added with the colon symbol For example 192 168 1 70 8080 GolP will send out all VolP calls to this address 3 4 1 2 Gatekeeper Mode The Gatekeeper Mode mode allows a user to setup the GolP Gateway by registering to the gatekeeper with one H 323 account A H 323 Phone Number H 323 phone number fill the login number E164 here B Gateway Prefix If login with a Prefix method fill the prefix number do not fill the Phone number C Display Name Display name is the name to be displayed on the called VoIP party D H 323 ID lf the system requires an H 323 ID as a method of Authentication enter the H 323 ID provided E Gatekeeper Address This field assigns the IP address or the domain name of the gatekeeper The port number can be added with the colon symbol For example 192 168 1 70 8080 F Enable Auth 18 One Chunnel GSM VoIP Gateway 1 235 Auth If H 235 Authentication is required enable this field and fill in the values as provided
14. P 2 0 UDP 192 168 2 189 5060 rport branch z9hG4bkK92531725 From lt sip 200011192 168 2 1 5060 gt user phone tag 740569827 To lt sip 8675588228822 192 168 2 1 gt Call ID 46471344300192 168 2 189 5060 Cseq 3 INVITE Contact lt sIip 20001 00192 168 2 189 5060 gt Max Forwards 30 User Agent HyberTonex Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY REFER REGISTER MESSAGE INFO SUBSCRIBE Content Type applications dp Content Length 226 Use can add a SMS prefix with mode 2 it will work like mode 1 Mode 3 example GolP use SMS Dial Mode 3 SMS Mode Dial SMS Dial Mode 3 bi One mobile phone s number is 86 13800000000 it sends a SMS 8675588228822 to GolP s GSM SIM card When GolP device receive this SMS it will auto to call number as 8675588228822 86 13800000000 and the caller number is GolP s SIP account number The sent out signaling as follow 33 One Chunnel GSM VoIP Gateway sending Message to 192 168 2 1 5060 INVITE sip 8675588228822 86 1 38000000000192 168 2 1 5060 transpor udp SIP 2 0 Via SIP 2 0 UDP 192 162 2 180 5060 branch 29h64bK620642232 From lt sip 200011192 163 2 1 5060 gt user phone tag 1333994780 To lt sip 8675588228822 86 13800000000 192 168 2 1 gt Call ID 52754291 40192 168 2 180 CSeq 2 INVITE Contact lt sip 20001 1192 168 2 180 5060 gt Max Forwards 30 User Agent HyberTone Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY R
15. P Address Subnet Mask Default Route Primary DNS Secondary DNS and other DHCP options from the DHCP host 2 Static IP Network Configuration LAN Port alot Mask optional igor DN S optional Choose Static IP if your network topology requires Please fill in Fill in the IP Address Subnet Mask Default Route Primary DNS and Secondary DNS 40 3 One Chunnel GSM VoIP Gateway optional as provided by your network administrator PPPoE Network Configuration LAN Port PPPoE wt PPPoE is a common dial up method for you network modem Cable xDSLs Choose this if your network environment requires Enter the User Name and Password as provided by your ISP 4 802 1q VLAN 5 This QoS feature requires your QoS support of your network to improve voice data traffics Please consult your network administrator for proper settings Advanced The Advanced settings allow the user to set the broadcast address and to clone a MAC address instead of using the factory preset MAC address Please consult your network administrator for further information Advance creces O SOON Address ls Address 3 10 2 PC Port Configurations The PC Port allows addition network devices to be attached behind the GolP Gateway It offers both Bridge and Static IP modes to meet your network topology Itis factory preset to the Static IP mode with the IP address 192 168 8 1 PC Port Static IP v IP Address 192 168 8 1
16. User Manual One Channel GSM VoIP Gateway Model GolP piscovery telecom Discovery Telecom Technologies skype discoverytelecom tel 1 801 7900348 www dtt tw info dtt tw One Chunnel GSM VoIP Gateway One Chunnel GSM VoIP Gateway Contents 1 Product INTFOGUCHION ussen srarnearnensee raven srensnnenengerdernndn 4 MESA A CrerT serena a eri ne nye Ter fem 4 AAA A A A A ene 4 13 ard Wales SPC CHICANO sd ls tl E 5 LA Software gt PEC AOL do 5 o 0d AA A O A A Mreenee Teen neces Te 5 OSTENDE 6 o Ae 7 AS AA A T 1 ZALMAN EEE E EE dos 8 ASIN VS COMMANDS retail sd 8 3 Configuration Guide nrsnansenarn eenen nensnenn 8 Sel Web onto tration MICA seal a iii 9 ED 10 3 A PROS AMO IMA ION nacidas 11 ARANA essa ince aera haa 11 3 2 3 GSM Module Information unne eenn eerneeenneernenenseesneeenseerneeenn 12 ICON OUT ONS ereen AA AA ARA AA A A EE 12 Oee eee 13 3 3 2 Time Zone and Time Server nnssnsvsnerenerenersnerenerenevenerenevenevenesenvenn 13 33 2 DIMF Min Detect Time Gas tendens 14 SSM AUO OMS Oreto erenn ne EEn as 14 9 SD INGIWOIK KONG oera e AE E E A ERES 14 320 0 GoM Group MOIS ci da 16 3 SPANO CIO ss ia 17 A PPP II A 17 SA 29 PRONG nnee eee 17 SN A O Tevet a run A Tne Onin ener nee 17 Oral Gatekeeper Mode murcia ill iiads 18 AA A bs ies 19 eZ O OMe atacante ie 20 SAS O arse daas 22 34 3 Media SEN enirere a e E E 24 34A Godec Predl A e Ena 26 SAS NAT TVS di E EEA EAA ounce 26 AA
17. ail SMS Mode Disable PSTN Forward Fail Forward Password This field sets the password protection for using the GSM connection If a password is entered the GolP Gateway will generate an indication tone and wait for the call to dial the 3 5 2 Auto Forward Call To PSTN When GolP Call divert options Forward Number VoIP To PSTN is empty GolP has a default call forward rule A When the be Caller ID is GoIP s SIP account number GolP will take the call and feed back a dial tone to VoIP caller The means is VoIP caller must dial PSTN number when hear this dial tone B When the be Caller ID isn t GoIP s SIP account number GolP will auto dial out this number thru GSM network C At this moment Dial Plan VolP to PSTN still working 3 5 3 Call Forward From PSTN To VoIP Forward to VoIP Enable Disable Forward Number PSTN To VolP Forward Password Po PSTN To VoIP Dial Plan P STH to Po VolP Forward Number Forward all incoming calls from the GSM connection to the VolP number specified in this field Forward Password is not required once this field is set If this field is blank the GolP answers an incoming GSM calls and then generates the VolP dial tone Please see below if the Forward Password is set The caller can then dial a VolP number manually At the end a pound can be dialed to activate the dialing of the VolP number immediately If not the VolP number is dialed after a preset time
18. ailable for media settings 24 A B C NY D One Chunnel GSM VoIP Gateway Media Settingss RIP Port range 16364 Packet Lenath ms Maximum Jitter sott limit Enable RC4 Encryption C Symmetric RTP Audio Codec Preference RTP Port Range This parameter specifies the range of the RTP Real Time Protocol Ports used by the GolP Gateway If your network limits the usable port range this parameter may need to be modified Please consult your network administrator for more information Packet Length This parameter defines the voice packet length The default setting is 20ms The range is from 5ms to 40ms at an increment of 5 ms Please note that some codes have a minimum packet length of more than 5 ms Jitter Buffer Mode Jitter Buffer Mode Fixed Minimun Jitter oa eg limit Since data packets may arrives at different orders the Jitter Buffer is used to hold the data packets received for re arrangement according to the packet sequence number Three Jitter Buffer Modes are supported Adaptive Sequential and Fixed The default is set to Adaptive mode with a minimum jitter of 60 ms and a maximum jitter of 220ms Please consult your network administrator for more information on the network environment in order to determine the optimal settings Media Qos Media QoS None IP TOS DiffServ Similar to the Signaling QoS the Media Qos in intended to improve the voice performance or quality I
19. all traversal both in parallel with a firewall and situated in the Internet as a Session Border Controller and also for hiding customer IP addresses calls are all routed through one point so that a public ITSP address can be used for accessing the customers rather than the customer s own IP address lf required enter this field with the outbound proxy IP address or domain name as provided 3 4 2 1 Advanced Settings Click on Advance Settings tab on the top right corner of the Call Setting page to display all the parameters available as shown below for programming These parameters allow more advanced control over the SIP signaling and media preference 22 One Chunnel GSM VoIP Gateway Advanced Settings lt lt Signaling Port 5060 SIP 183 NAT Keep alive Enable Disable Advanced Timing Signaling QoS None Signaling Encryption Mone Signaling NAT Mone Traversal Media Settings A Signaling Port SIP Local port The default SIP port is 5060 Change this as required B NAT Keep alive NAT Keep alive Enable Disable The NAT Keep alive feature sends a null packet to the SIP Proxy periodically in order to keep the NAT open for incoming data traffics C Advanced Timing Settings Advanced Timing Sue E IO 32 1805 aa A 000ms Retransmit T 2 2000 2000ms Some SIP proxies may have special timing requirements Change these parameters as required D Signaling Qos Sig
20. defines the event to be matched A event consists of a sequence of digits Ifa u One Chunnel GSM VoIP Gateway specific digit has a limited range use the syntax A B where A and B are both digit 0 to 9 and B is greater than A The length of the input number can be limited by using X to represent each unknown digit If this field is omitted it means any event lt action gt defines the action to be taken on the number received and it consists of minus plus and digits followed by digits means to remove the digits from the beginning of the number entered followed by digits means to add the digits in front of the number entered means or and the order of priority is from left to right Note For practical use it should not be possible to reach the maximum length of the Dial Plan string Examples 1 Dial Plan 010 010 means that the number dialed out will have the first 3 digits 010 removed when a number with the first digits as 010 is entered a Number entered 01082121234 actual number dialed 82121234 b Number entered 82121234 actual number dialed 82121234 2 Dial Plan 1 00 means that the number dialed out will have the 00 added in front of the number entered when a number with the first digit as 1 is entered a Number entered 1082121234 actual number dialed 00182121234 b Number entered 8
21. e a aa a a i 26 340 2 Media NAT IrIversa lneriikide dal a aake 21 DAO GUM DT 28 3 5 1 Call Forward From VoIP To PSTN eener eenn venneerenseerenseeren 28 One Chunnel GSM VoIP Gateway 3 0 2 AUO Forward Call To PSTN iieiaei a E 29 3 5 3 Call Forward From PSTN To VolP ooooooooccoccconoccnonononononcconancconanaconananonananonos 29 30 SMS DAS OS cl et cas orcs a Tak sa ee erica iets TARA TR A ROA 30 326 ONS Salles anat 30 902 oM AV tender teelden 34 3 6 2 1 SMS Relay To VoIP System ccccccccccccncnonnnnnononononcnnncnocnnnnnnnnnnnononnnnnaninnnnnnss 34 3102 25 NS Relay To GS MUN E WOt Estaria ada 35 SL PSTN Caller ID TES A caia 35 ORO DEUR AN OR 37 SA A diesel A 39 LON SE Work CORTS oN Rs 39 SOLANO 40 3 102 PG POE UA IAS ee 41 3 11 Save CoONTIQULAtION ccccccccncncnnnnnononononnnnnnnnnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnnnnnnnnnnns 42 ADAMS AS AAPP a O O II II 43 3 13 Tools MEVA A E 43 3 13 1 Online Upgraden zun densan ennen db tokaellde 43 3 182 Change PASS WONG sostiene teheran cti ie caian 44 3 193 HESeCL CONMOGUIALION verre 44 3 134 REDOOL ING Devin 44 4 Hardware Specifications nnen eneen enen een enenn 45 5 Manufactory Parameters nnee neen 45 One Chunnel GSM VoIP Gateway 1 Product Introduction 1 1 General Information A VoIP GSM Gateway enables direct routing between IP and GSM network without the use of a FXO port or the PSTN network With this device the usage of VoIP is greatly enha
22. erver Mode When GolP running in Server Mode lt can auto forward the GSM s incoming call to any free client GolP devices At this moment you only offer this GolP s GSM number to your user Client Mode When GolP running at Client Mode It will auto send itself GSM number and state to Server GolP device and waiting the incoming call forward from Server GolP You must enter itself GSM number and Server GolP device s IP address into follow option 16 One Chunnel GSM VoIP Gateway GSM Group Mode As Client ad Disable When GolP run as alone mode please set it to Disable 3 3 7 Auto Reboot M Auto Reboot Reboot Time 04 00 This option enable GolP auto reboot each day GolP will auto reboot itself at Reboot Time If meet a current called the action will auto delay after the call finish 3 4 Call Settings Click on the Call Settings to configure the VolP call settings The first thing to set is the Endpoint Type H 323 or SIP Call Settings Endpoint Type H 323 Phone a H 323 Phone SIP Phone 3 4 1 H 323 Phone For H 323 protocol 2 Endpoint Modes are supported Direct Mode and Gatekeeper Mode Call Settings Endpoint Type H 323 Phone Endpoint Mode Direct Mode hd Direct Mode Gatekeeper Mode 3 4 1 1 Direct Mode In Direct Mode GolP running at H 323 P to P type 17 One Chunnel GSM VoIP Gateway Call Settings Endpoint Type H 323 Phone Advanced Settings gt Endpoint
23. f your local network supports QoS 25 One Chunnel GSM VoIP Gateway 3 4 4 Codec Preference Codec Preference allows a user to select the codes to be used and its priority to be selected for a voice call Audio Codec Preference lay g729 97293 g729ab g7231 Click on the check box to enable a codec Select a codec and then press the UP or DOWN button to move the position of the codec on the codec list with a priority in descending order Note The voice code alaw and ulaw is G 711a and G 711u 3 4 5 NAT Traversal 3 4 5 1 Signaling NAT Traversal Signaling NAT traversal may be required if the GolP Gateway is put behind a NAT or multiple NATs Depending on your network environment and SIP Server capabilities this feature may or may not be turn on Signaling NAT Traversal STUN RFC 3489 Relay Proxy A None Select None to turn off this feature B STUN RFC 3489 STUN Simple Traversal of UDP User Datagram Protocol through NATs Network Address Translators is a network protocol allowing a client behind a NAT or multiple NATs to find out its public address the type of NAT it is behind and the internet side port associated by the NAT with a particular local port Select STUN RFC 3489 to use a STUN server for Signaling NAT Traversal Enter the IP Address or the domain name of the STUN server to be used C Relay Proxy Relay proxy is a proprietary NAT traversal technology Please consult your service 26
24. ion Call Divert o LAN Port DHCP PC Port Static IP save Changes 802 14 VLAN O Enable Disable IP Address 192 168 8 1 Discard Changes Advanced Subnet Maak a DHCP Server O Enable Disable Toals Adwanced Call Settings Endpoint Type H 323 Phone w Advanced Settings Endpoint Mode Gatekeeper Mode wl Media Settings Contig Mode Single Contig v Click on Preference in the left menu of the configuration web and the screen will be displayed as below 12 One Chunnel GSM VoIP Gateway Preference Language iF5 fale pt Network Tones B Time Zone GSM Group Mode Disable H Time Server V Auto Reboot DTMF Min Detect RebootTime p n Time Gap Auto provision C Enable Disable 3 3 1 Language Currently GolP supports English Simplified Chinese and Traditional Chinese Select the language desired and the Web page will be shown in the language selected accordingly Preference Language Z s fale PE fal par The language can also be selected at the top of the web page Once selected the webpage language is refreshed immediately However the language selection is not saved until the Save Changes icon is clicked 3 3 2 Time Zone and Time Server The GolP Gateway supports Network Time Protocol NTP to obtain the date and time information from an NTP server Time Server The time zone is specified as in GMT offset For example the Pacific Standard Time i
25. ites be call number 30 One Chunnel GSM VoIP Gateway D SMS Dial Prefix When GolP dial a SMS call it will automatic add this option s digit in be Called ID e Mode 1 examples A GolP use SMS Dial Mode 1 SMS Mode Dial SMS Dial Mode 1 SMS Dial Prefix One mobile phone s number is 86 13800000000 it sends a SMS 8675588228822 to GolP s GSM SIM card When GolP device receive this SMS it will auto to call number 8675588228822 and the caller is number 8613800000000 The sent out signaling as follow sending Message to 192 168 2 1 5060 INVITE sip 8675588228822 0192 168 2 1 5060 transport udp SIP 2 0 Via SIP 2 0 UDP 192 168 2 189 5060 rport branch z9hG4bK1686911003 From lt sip 8613800000000 192 168 2 1 5060 gt user phone tag 62691 8067 To lt sip 8675588228822 0192 168 2 1 gt Call ID 1835068843 192 168 2 189 5060 CSeq 2 INVITE Contact lt sip 8613800000000 192 168 2 189 5060 gt Max Forwards 30 User Agent HyberTone Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY REFER REGISTER MESSAGE INFO SUBSCRIBE Content Type application s dp Content Length 226 B GolP use SMS Dial Mode 1 and add a prefix as 999 SMS Mode Dial we SMS Dial Made 1 w SMS Dial Prefix 999 One mobile phone s number is 86 13800000000 it sends a SMS 8675588228822 to GolP s GSM SIM card When GolP device receive this SMS it will auto to call number as 9998675588228822 and
26. l flash 100ms ON and 100ms OFF 2 When the GolP is login your softswitch this LED will flash 1s ON and 1s OFF When the GolP s GSM login the ISP s system this LED will flash 1s ON and 1s OFF 2 4 SMS Commands GolP supported commands come from SMS FUNCTION SMS CONTENT REMARK Obtain LAN Port Info Not distinguish majuscule and lowercase RESET Password Not distinguish majuscule and lowercase Reboot device REBOOT Password Not distinguish majuscule and lowercase Note In command Reset and Reboot the Password is the GolP device s admin password The command keywords can use majuscule and lowercase but the password must distinguish majuscule or lowercase 3 Configuration Guide To configure the GolP Gateway you must login to its Web server via the LAN or PC port The LAN port is factory preset to obtain an IP from the local DHCP host and the PC port is set to the fixed IP 192 168 8 1 One Chunnel GSM VoIP Gateway If a local DHCP host is available the LAN will obtain an IP address automatically To listen to the IP address assigned just dial a call via the GolP Gateway s SIM card phone number When the call is connected you will hear a dial tone Just dial 01 for English voice prompt on the LAN IP and 00 for Chinese voice prompt on the LAN IP The LAN IP Address can also be obtained by sending a SMS message to the GSM phone number The GolP will then reply with a SMS message containing the LAN IP address
27. naling QoS IP TOS DiffServ 25 One Chunnel GSM VoIP Gateway Signaling QoS improves the performance of SIP signaling If local network device supports Qos select this field accordingly Please consult your network administrator for further information E DTMF Signaling 1 DTMF TYPE DTMF signals can be sent over to the called party once a call is established GolP Gateway supports both Inband and Outband DTMF signal types DTMF Signaling Outband nt Gutband For Inband DTMF type DTMF signals are generated locally at the calling phone and then send to the called party as part of the voice signals This method is not reliable since the quality of the DTMF signals is subject to the Codec used and the quality of the network traffics For Outband DTMF type DTMF signal commands are sent to the called party and the actual DTMF signals are actually generated by the called party This method allows more reliable DTMF signaling However it requires the called party to support this feature in order for this to work properly GolP Gateway supports both RFC2833 and SIP INFO Outband DTMF protocols 2 DTMF Payload Type DTMF Payload Type is by RFC2833 protocol to carry the tone definitions for various applications The default DTMF Payload Type is 96 Please consult your VoIP service provider for the proper setting if required 3 4 3 Media Setting Click on Media Settings in the Call Setting menu to access the parameters av
28. nced with significant savings on long distance and roaming charges al ae ias Softswitch PSTN Gateway Internet ff Pi P 1 2 Protocol TCP IP V4 IP V6 auto adapt ITU T H 323 V4 Standard H 2250 V4 Standard H 245 V7 Standard H 235 Standard MD5 HMAC SHA1 ITU T G 711 alaw ulaw G 729A G729AB and G 723 1 Voice Codec RFC1889 Real Time Data Transmission Proprietary Firewall Pass Through Technology SIP V2 0 Standard Simple Traversal of UDP over NAT STUN VV VV VV V VV V VV VV VV VV V V One Chunnel GSM VoIP Gateway Web base Management PPP over Ethernet PPPoE PPP Authentication Protocol PAP Internet Control Message Protocol ICMP TFTP Client Hyper Text Transfer Protocol HTTP Dynamic Host Configuration Protocol DHCP Domain Name System DNS User account authentication using MD5 Out band DTMF Relay RFC 2833 and SIP Info 1 3 Hardware Specification VV VV WV ARM9E Processor DSP for voice codec and voice processing Two 10 100 BaseT Ethernet ports with full compliant with IEEE 802 3 LEDs for Ethernet port status One GSM Connection 1 4 Software Specification VV VV VV VV VV vvv LINUX OS Built in HTTP Web Server PPPoE Dial up NAT Broadband Router Functions DHCP Client DHCP Server Firmware On line upgrade PSTN Caller ID transmit Multiple Language Support Supported call divert Supported PSTN auto call out to PSTN Supported Multi_devices Coopera
29. out Forward Password 29 One Chunnel GSM VoIP Gateway This field sets the password protection for incoming GSM calls If a password is entered the GoIP Gateway will generate an indication tone after answering an incoming call The caller is then ready to dial the password Once the password is correctly entered the GolP Gateway generates a VoIP dial tone and waits for the caller to dial a VoIP number 3 6 SMS Disposal 3 6 1 SMS Call Out GolP Gateway supported SMS call In this mode when GolP Gateway received a SMS send from any one mobile phone it will auto make a call to SIP server lf you want use this function select the SMS Dial option in configuration page Call Divert Forward to PSTN Enable Disable SMS Mode a pen SMS il Mode 1 E VolP To PSTN Forward Password po SMS Dial Prefix fo VoIP To PSTN Dial Plan VolP to A PSTN Forward Fail Drop The Call PSTN CID Forward Enable Disable Forward to VoIP Enable Disable ed PSTN To VolP Forward Password Po PSTN To VolP Dial PlamPSTH to WolP GolP supported three types SMS Dial SMS Mode Dial hi SMS Dial Mode 1 A Mode 1 GolP dial the call use SMS sender call ID B Mode 2 GolP dial the call via itself VolP account and add the SMS sender phone number to Call Divet option s Forward Number VoIP to PSTN automatic C Mode 3 GolP dial the call via itself VoIP account and add the SMS sender phone number to SIP inv
30. ow the meaning of various rules They may not have any practical meaning A combination of these rules joined with the symbol can be realized for a much more complicated dialing application 3 9 Gain Settings A hidden webpage is provided to set the receiving and transmit gains of VolP Chunnel The URL link is http xxx xxx xxx xxx defaulten US gain html THIS PAGE IS INTENDED FOR AN EXPERIENCED USER OR AN ADMINISTRATOR ONLY PLEASE SET THE GAINS WITH CAUTIONS j ZEE ABD 280 ERW TAD Rio Ou O 120 Pe km oea Luo EIE 48 http 192 168 2 228 defaul t en US gain html Google G JRO OG dy pg Poh O Gain Settings Line 1 Line 1 Output Gain o E Line 1 Input Gain 2 Note A too low or too high input gain MAY affect the sensitivity of DTMF detections 3 10 Network Configuration Click on Network tab in the left menu column to configure the LAN and PC ports 39 One Chunnel GSM VoIP Gateway Network Configuration LAN Port PPPOE we PC Port static IP wt 802 1q VLAN Enable Disable Advance Advance gt gt 3 10 1 LAN Port Three LAN Port modes are supported DHCP Static IP PPPoE Network Configuration LAN Port E User name Password 802 1q VLAN Enable Disable VLAN i mem vanos S S Advance lt e O l Address oo gt Address 1 DHCP Choose DHCP if a local DHCP host is available This allows the GolP Gateway to obtain network information I
31. r Register Expiry s Outbound Proxy fo Home Domain fo AuthenticationID sd Dial Plan fo Call Forward Type Call Forward Number fo Backup Server O Enable Disable Phone Number Enter a SIP phone number SIP Proxy Enter the SIP proxy IP address or domain name If the registration port isn t 5060 then add and the port number An example is sip dtt tw 8080 SIP Registrar Server lf the Registrar Server is different from the SIP Proxy enter its IP address or domain name in this field If the registration port isn t 5060 then add and the port number An example is sip dtt tw 8080 Home Domain SIP Networks sometimes use the Home Domain name as an identifier Enter this field as required E Authentication ID F G H Enter the Authentication ID as provided Password Enter the authentication password as provided Display Name Enter this field for the name to be displayed on the called VolP party Backup Server 21 One Chunnel GSM VoIP Gateway Backup Server aa Registrar ri Domain Fail retry Interval 1 po 60s The GolP Gateway supports one Backup Server as an alternative to the main server Once registration to the main server fails the GolP Gateway will try to register to the Backup Server Outbound Proxy OutBound proxies are devices that will forward SIP signaling and frequently RTP media traffic too OutBound proxies are used for a number of reasons including firew
32. rites Ea A es 3 Address 192 168 8 1 If the connection is correct the Web Browser will prompt you to enter the User name and Password as shown below The server 192 168 at Please Login requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name ern Remember my password Enter the User name and Password and the press OK to access the GolP Gateway Web Server The default for both user name and password is admin 3 2 Status The Status page shown below is the default home page of the GolP Web server 10 One Chunnel GSM VoIP Gateway Phone Information Network Information GSM Module Information Serial Number GOIP08030031 LAN Port 1921682219 GSM Model GTMS00A4 Firmware Buea LANMAC 00 11 8E 01 50 85 GSM Signal 27 Version Hardware PC Port 192 165 5 1 GSM Status LOGIN GalP Model l PPPoE Disabled Phone Status LOGOUT Default 1421582254 Route DNS Server 20205134 133 3 2 1 Phone Information A Serial Number Each Gateway has a unique serial number assigned by the factory such as GOIP08030031 This number is important for centralized configuration technical support and warranty This number is printed on the bottom of the Gateway and is associated with your software license B Firmware Version Firmware version identifies the firmware
33. s GMT 8 and the Pacific Daylight Time is GMT 7 Time Zone GMT 8 Time Server pool ntp org Note The GolP Gateway supports CDR and Billing Information it is important to set up these two parameters properly 13 One Chunnel GSM VoIP Gateway 3 3 3 DTMF Min Detect Time Gap DTMF Min Detect Time Gap This parameter use to limit two same DTMF digits minimum time gap the range is 60ms to 120ms default is 80ms If you encounter double digit problem gain it to more if you encounter lose digit then gain it to less 3 3 4 Auto Provision The GolP Gateway supports Auto Provisioning which enables configuration parameters to be set automatically without human intervention The Auto Provisioning supports both HTTP and TFIP protocols For higher security encrypted configuration file is also supported This feature requires external Auto Provisioning Server Please contact your service provider for further information on this Auto provision Enable Disable Provision Interval fs 3 3 5 Network Tone Network Tones are a set of tones used for VolP calls Select one of the countries defined or customized to define your own Network Tones Network Tones China Australia China Hong Kong Mew Zealand United Kingdom United States Customized You can configure the Network Tones as Customized option 14 One Chunnel GSM VoIP Gateway Network Tones Dial Tone fs Ring Back Tone Indication Tone fs Each tone li
34. sted above is defined in the following format nc rpt c1on c1off c2on c2off c3on c3off f1 f2 f3 f4 p1 p2 p3 p4 Where nc is the number of cadences rpt is the repeat counter 0 infinite 1 n repeat 1 n times c1on is the cadence one on in milliseconds c1off is the cadence one off in milliseconds c2on is the cadence two on in milliseconds c2off is the cadence two off in milliseconds c3on is the cadence three on in milliseconds c3off is the cadence three off in milliseconds f1 is the tone 1 frequency 300Hz 3000Hz f2 is the tone 2 frequency 300Hz 3000Hz f3 is the tone 3 frequency 300Hz 3000Hz f4 is the tone 4 300Hz 3000Hz p1 is the attenuation index for f1 0 31 p2 is the attenuation index for f2 0 31 p3 is the attenuation index for f3 0 31 p4 is the attenuation index for f4 0 31 0 3dB 1dB increments 0 3dB 1dB increments 0 3dB 1dB increments 0 3dB 1dB increments ee ee m AA For example the tone definition for a tone of 450Hz with a cadence of 700 ms on and 1000 ms off is 1 0 700 1000 0 0 0 0 450 0 0 0 20 0 0 0 15 One Chunnel GSM VoIP Gateway 3 3 6 GSM Group Mode _ GSM Network Internet Server Mode GolP Incoming call forward to Client GolP GolP supported multi_devices cooperate with one group it can work like a multi_chunnels GSM gateway Any one GolP are can work as Group Server Mode or Client Mode As Server As Client S
35. te Mode Group Mode Supported SMS call out 1 5 List of the Package a b c One GolP Gateway main unit One DC4 5V 2000mA power adaptor One Ethernet cable 3M One Chunnel GSM VoIP Gateway 1 6 Appearance One Chunnel GSM VoIP Gateway 1 LAN Connect this port to an Ethernet Switch Router the Ethernet of a DSL modem or other network access equipment 2 PC Connect a computer or other network device to this port 3 POWER DC4 5V 2000mA Connect the 4 5V 2000mA Adapter provided to this power jack 4 Reset Press this button to reset the GolP Gateway to factory defaults 2 Installation 2 1 Installation Steps PC PC A a GSM Network Ie an a o 7 Plug to Internet Internet DASL Cable Modem Ethernet Please follow the connection diagram above to install the GolP Gateway a Insert a GSM SIM card in the SIM card compartment located at the bottom of the GolP Gateway s One Chunnel GSM VoIP Gateway b Connect an Ethernet cable the LAN port of the GolP Gateway and the other end to your existing network equipment c Connect an Ethernet cable to the PC Port of the GolP Gateway and the other end to a PC or other network device Optional d Connect the power adapter provided to the power jack of the GolP Gateway 2 3 LED Indicators The following table defines the status of the LEDS located on the top case and on the RJ 45 connectors LED DESCRIPTION 1 When the GolP is booting this LED wil
36. the caller is number 8613800000000 The sent out signaling as follow 31 One Chunnel GSM VoIP Gateway Sending Message to 192 168 2 1 5060 INVITE sip 9998675588228822 192 1682 1 5060 transportudp SIP 2 0 Via SIP 2 0 UDP 192 168 2 189 5060 rport branch 29hG4bK1686911003 From lt sip 861 380000000001 92 168 2 1 5060 gt user phone tag 626918067 To lt sip 999867558822882241192 168 2 1 gt Call ID 1835068843192 168 2 189 5060 CSeq 2 INVITE Contact lt sip 2613800000000 192 168 2 189 5060 gt Max Forwards 30 User Agent HyberTone Allow INVITE ACK BYE CANCEL OPTIONS NOTIFY REFER REGISTER MESSAGE INFO SUBSCRIBE Content Type application sdp Content Length 226 Mode 2 example GolP use SMS Dial Mode 2 SMS Dial 2 One mobile phone s number is 86 13800000000 it sends a SMS 8675588228822 to GolP s GSM SIM card When GolP device receive this SMS it will auto to call number as 8675588228822 and the caller number is GoIP s SIP account number GolP will set the SMS sender number to Call Divert option s Forward Number VoIP to PSTN automatic The result is when SIP server receives the SMS call and call back this GolP then GolP will auto call the SMS sender via GSM network The sent out signaling as follow 32 One Chunnel GSM VoIP Gateway Sending Message to 192 168 2 1 5060 INVITE sip 8675588228822 0192 168 2 1 5060 transport udp SIP 2 0 Via SI
37. tiple Times In this mode the GolP Gateway will register like two terminals DTMF Signaling 1 DTMF TYPE DTMF signals can be sent over to the called party once a call is established GolP Gateway supports both Inband and Outband DTMF signal types DTMF Signaling Outband nt nband Qutband For Inband DTMF type DTMF signals are generated locally at the calling phone and then send to the called party as part of the voice signals This method is not reliable since the quality of the DTMF signals is subject to the Codec used and the quality of the network traffics For Outband DTMF type DTMF signal commands are sent to the called party and the actual DTMF signals are actually generated by the called party This method allows more reliable DIMF signaling However it requires the called party to support this feature in order for this to work properly GolP Gateway supports RFC2833 Outband DTMF protocols 2 DTMF Payload Type DTMF Payload Type is by RFC2833 protocol to carry the tone definitions for various applications The default DTMF Payload Type is 96 Please consult your VolP service provider for the proper setting if required 3 4 2 SIP Phone Set the Endpoint Type to SIP Phone for connections to SIP Servers 20 One Chunnel GSM VoIP Gateway GolP Gateway s SIP configure page as follow Call Settings A B C NY D Endpoint Type single Server Mode Phone Number Display Name SIP Registra
Download Pdf Manuals
Related Search