Home

USER MANUAL

1. Deletes the data of the selected pattern Run Pattern Runs the Pattern for the test purposes to check if it works properly Edit Pattern Edits the selected pattern Pattern Edit EDIT PATTERN 1 IN l MOVE TO START POSITION NEAR START FAR CANCEL NEAR SAVE FAR DELETE O O X1 N 1 With the Joystick of your controller move the camera to the start position with an appropriate zoom magnafication To start the pattern recording press NEAR key To exit press FAR key 2 Move camera with joystick of controller or run preset function to memorize the path mostly curve path in the selected pattern The movement by Joystick and preset movement will be memorized in a pattern After a pattern is programmed the remaining storage is displayed in progress bar on the screen 3 To save the data and exit press NEAR key To cancel saving the data and delete the data press FAR key 54 Ll legrand 4 10 Group Setup ER ee cho a T ee ee 2 GROUP NO 1 UNDEFINED CLEAR GROUP CANCEL RUN GROUP lt EDIT GROUP gt Group Number 1 8 Selects a Group number to edit If the selected Group number is not defined UNDEFINED will be displayed under the selected Group number Clear Group CANCEL OK Deletes the data of the selected Group Run Group Runs the Group for the test purposes to check if it works properly e Edit Group Edit the selected Group Group Edit EDIT GROUP 1 NONE NONE NO
2. GFF ihe Maru s Cymen Ouen 15 CameraID Camera ID Setup e ID numbers of cameras are set up with binary numbers See the examples shown below Ex ID 5 Ex ID 10 The camera ID range is 1 255 Camera ID must not be 0 Factory default of Camera ID is 1 e The factory default of the camera ID is 1 e Match the camera ID with the Cam ID setting of your DVR or Controller to control the camera e lf you are connecting a single camera to a controller terminate the camera When connecting more than one camera to a single controller terminate the last camera on the communication line The last camera means the camera farthest in cable length from the controller e Note that the total length of the communication cable between a controller and the camera s on the same communication line must be less than 1 2Km Communication Protocol Setup e Select the appropriate Protocol with DIP switch combination PO P1 P2 Protocol Baud rate Pin 1 Pin 2 Pin 3 OFF OFF PELCO D 2400 bps PELCO P 4800 bps PELCO P 9600 bps OFF PELCO D 9600 bps e If you want to control using DVR or P T controller their protocol must be identical to camera Otherwise you can not control the camera e lf you changed camera protocol by changing DIP S W the change will be effective after you reboot the camera e Factory default of protocol is Pelco D 2400 bps 16 LI legrand Terminal resis
3. 5 1 Dimension 4 305 21 Model Main Body Surface Mount Type 127 MPS Unit mm 65 4 305 22 Model Main Body amp Terminal Cover vods i f yd e fee TN SE ROU aaan H E o 3 2 GE Ed i a D nr PRE ns 4 R UN iE E Unit mm E E E E H 2 i de He wb H a oem In Ceiling Mount Bracket 170 p sunt e Wall Mount Bracket M Bis i Es 66 Ll legrand 4 305 23 Model Main Body Ceiling Mount Type Wall Mount Type Unit mm 67 SSS oue OO OO O SR Vmw 4 305 24 4 305 25 Model Main Body Ceiling Mount Type e Wall Mount Type 138 6 Unit mm 68
4. Assigns colors of masks to block light sources A6 Ll legrand 4 6 Motion Setup MOTION LOCK PWR UP ACTION AUTO FLIP ON JOG MAX SPEED 120 SEC JOG DIRECTION INVERSE FRZ IM PRESET OFF PARKING ACTION SETUPS Sets the general functions of Pan Tilt motions e Motion Lock Power Up Action Auto Flip Jog Max Speed Jog Direction 6 Freeze in Preset ON OFF If Motion Lock is set to ON it is impossible to set up and delete Preset Swing Pattern and Group It is possible only to run those functions To set up and delete those functions enter into OSD menu ON OFF Refer to Other Functions section ON OFF Refer to Other Functions section 1 sec 3609 sec Sets the maximum jog speed Jog speed is inversely proportional to the zoom magnifications As the zoom magnification goes up the pan tilt speed goes down INVERSE NORMAL Sets the Jog Direction If this is set to Inverse the view direction in the screen is same as the direction of joystick If this is set to Normal the view direction in the screen is the reverse dirction of joystick ON OFF Sets Frame Freeze Function This feature freezes the scene on the monitor when going to a preset At the start point of a preset movement a camera Starts freezing the image of the start point Camera keeps displaying the image of the start point during preset movement and does not display the images which camera gets during p
5. f 3 6 44 3 mm Angle of View H 5444 Wide 4 64 Tele V 41 42 Wide 3 52 Tele 2 0 Lux Color Sens Off 0 0008 Lux B W Sens x256 50 IRE F1 6 1 60 50 1 10000 sec x2 256 Sens UP Auto Manual Red Blue Gain Adjustable 2000 K 10000 K 60 LI legrand Specifications 4 305 22 4 305 22 Video Signal System PAL 795 H x596 V 470K 752 H x582 V 440K 550 TV Line Color 680 TV Line B W f 3 5 94 5mm F1 6 2 9 0 4 Lux F1 6 Color 0 02 Lux F1 6 B W 50 IRE Auto Day Night ICR Camera Auto Manual Red Blue Gain Adjustable Pan 360 Endless Tilt 95 Pan Tilt Speed 0 05 360 sec proportional to zoom Pan Tilt 127 Preset Label Camera Image Setting 4 Pattern 1200 commands about 5 minute Pattern 8 Group 20 action entities per Group Dimension 2160 x 212 H mm Weight about 2 kg Operating Temp 0 C 40 C Specifications of this product can be subjected to change without notice Specifications 4 305 24 4 305 25 eI SD MT 550 TV Lines Color 680 TV Lines B W wmm n Cos PE Angle of View H 55 5 Wide 2 24 Tele 55 5 Wide 1 59 Tele Angle of View V 42 5 Wide 1 79 Tele 42 5 Wide 1 19 Tele Minimum Illuminance 0 4 Lux Color 0 02 Lux B W 50 IRE 0 7 Lux Color 0 6 Lux F1 6 B W 50 IRE F1 6 1800 K 10500 K we 62 Movement Range LI Pan Other Pan Tilt Functions Communication Operation Temper
6. 4 305 22 model cccccccccccccccccccccccccccccccccceceeeeeooooooooouses 23 2 7 Installation using Wall Mount Bracket 4 305 22 modlel e c Lecce eee e eee e eee eaae eee 24 2 8 Installation with Ceiling Mount Bracket 4 305 23 4 305 24 4 305 25 Models 25 2 9 Installation with Wall Mount Bracket 4 305 23 4 305 24 4 305 25 Models 26 2 10 Wiring and Cabling 4 305 21 4 305 23 4 305 24 4 305 25 cere eee cete eere eene eee eene eenas 27 3 ODBerdllOlsanissceeonet GG OWN TOI IN UII IN HIR 32 41 CHECK Points pelore Operatii uses isse EE ERR RREERERERENNSEFEVEEESUR Ge NN ENS USES ES V EP rR Iv V T eaa eeu ee eu ese eed suos va vr dettes 32 3 2 Check Points for Preset and Pattern Function before Operation see 32 zem pee Hr HE ARY IR FR Y FR FFF er 33 29 4 Reserved Presets HOLE KeVS she ee oi eee eu neni RSS ANNOG ONS SODA DAYS SANG IER ERR P NON NOU SOS RR ORROO 33 39 PROS OU rU 34 30 SWIN O HY 34 3 6 a A RM 35 3 87 Cie mc FRYN YNYR 36 3 9 Other ulipeiro rp S 37 3 10 OSDDISplay se c aient 38 A OSDMENU GG E DIEM 39 Al QuickProgramming Guide ui Rs Net ss RS 39 MEN ge 39 ASS DISDIAYV SQUID Ga Y WN A A A A AU AAG En On nwn 40
7. 44 Privacy Zone Mask SelUD saisit e uo niet ERA RR sabes eu abe eae v sube babe YN add YDDYN UE ERE EAR EIE asias 41 LI legrand 4 5 Camera Setup Dome Camera Setup Men wu ccsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssees 43 46 Monon SBLUD sinieteirieieiieiniein YY ARR EFE COI dTt tI 47 A Peel SOUDE io noie mis D d MIS 50 40 SWING SOU asser Le een sperme 53 A9 Paent SOU nie did anndessdatenet ess ais scenic ie unies inertie 54 4 10 Group SEUD UC NA AAA T 55 4 11 SVSICHLEITIHNIAHZOUH OT NND O aaa aaa Y UU UN Y 58 D SPDECIHOCaUODS au GG YE OEA ain sn GYFNOD 60 5 1 Blur e EFA 65 1 INTRODUCTION 1 1 MODEL CODE Mini plastic Aluminium Aluminium Mini Aluminium Aluminium with j small with with with fan heater fan heater fan heat fan heater an heater a S Video Video signal mount bracket Rated power 12 VDC In Out Trigger alarm 3 In 1 Out 4 In 2 Out 3 In 1 Out 1 2 FEATURES Powerful Zoom Camera amp Setup Options Optical Zoom DigitalZoom Zoom Max zoom EL e m gm m magnification i PP Day amp Night or Auto Focus Manual Focus Semi Auto Focus e lun HAD va super HAD va super HAD ie SPA Ole CCD A color CCD color CCD color CCD P Powerful Pan Tilt Functions MAX 360 sec High Speed Pan Tilt Motion With the Vector Drive Technology Pan Tilt motions are accomplished alon
8. Focus Mode AUTO MANUAL SEMIAUTO Sets camera Focus mode O SEMIAUTO Mode This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus mode by operation Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation With Manual mode at presets Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as camera arrives at presets It should shorten time to get focuses Focus mode automatically changes to Auto Focus mode when jog operation starts Digital Zoom ON OFF Sets the digital zoom functions to ON OFF If this is set to OFF the optical zoom function runs but the zoom function stops at the end of optical zoom magnification Image Flip ON OFF Sets System Image Flip Function to ON OFF When this function is set to ON flipped images always come out When the camera is installed as Desktop type set to ON to get proper images e Sharpness 0 3 Sets image sharpness to enhance pictures 43 White Balance Setup WB SETUP GLOBAL WE MODE RED ADJUST e WB Mode AUTO MANUAL Retains color balance over a color temperature range In auto mode this feature automatically processes the viewed image In Manual mode Red and Blue level can be set up manually Red Adjust 10 255 Adjusts the picture output in the red range e Blue Adjust 10 255 Adjusts the picture output in the blue r
9. X Wiring and Cabling 4 305 22 model EM RS 485 G UD ET S pe f A s i Output Devices Power Connection e Please check the voltage and current capacity of rated power carefully Rated power is indicated in the back of main unit Input Voltage Range Current Consumption 11 15 VDC 0 75 A Video Connection e Connect with BNC coaxial cable 30 Ll legrand E R MUS Alarm I O Connection e Sensor Input Internal IN COM _ PL LIN 1 Sensor 1 Output NC A fl TT u INA ISO 4 Output c Before connecting sensors check driving voltage and output signal type of the sensor Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general the cabling must be done properly after considering these typed Also the sensor type i e Normal Open or Normal Close in Dip switch in main body of camera must be set properly Description IN COM Connect cable of electric power source for Sensors to this port as shown in the circuit above IN1 IN2 IN3 In4 Connect output of sensors for each port as shown in the circuit above e Relay Output ce ey AC or DC 1 f eU QUT Ra ENS HH IN A ON LOAD AC or DC OUT 2 E LOAD Maximum allowable electrical load of relay is shown bellow table DC 28V 3A AC110V 3A 31 UJ 3 Operation 3 1 C
10. Avoid installing in humid or dusty places e Avoid installing in places where radiation is present e Avoid installing in places where there are strong magnetic fields and electric signals e Avoid installing in places where the product would be subject to strong vibrations Table of contents Important Safety GUIde a 2 CAUTION Si GG YY DE FYNYDD t FD ED UNFED NR 3 L INTRODUCTION Gi Y YY FN Y ON FAU 6 ld MODEL CODE ued UA du ad ed ei i dedd irit du iadu ada oud te i e RY GEN tio OF dddo 6 1 FEATURES aea E A A A eee 6 1 3 PackadeConiDponent ene idd TR 9 1 4 j Main Part DeScHDHOD y sisien FEN EY FNFAF NAF FO FO NY Y NF Y Y A WY Y FN RR NR NR RR UU UR 11 Z INSTALLATION sesivsscsasesssssnscesecenscsevtvwvsndecuncaseuensssssscuancesetavennsnsvaviewesasessysosnsusaeseveunseannvdevesneassvonssiseseaness 15 2 1 PDT SWIG BST LU ER C M RR CD 15 2 2 In Ceiling Mount Installation 4 305 21 Model eee e eene ee e e ee eee eee eee eese tete eeesssoooeoeee 19 2 3 Installation with Surface Mount Bracket 4 305 21 Model 4 ecce ecce eee eee eee eee eese 20 2 4 Direct Installation on the Ceiling 4 305 22 model cccccccccccccoooo000000000000000000000000000000000000000000000000 21 2 5 Installation using In Ceiling Mount Bracket 4 305 22 model eee 22 2 6 Installation using Ceiling Mount Bracket
11. Preset Pattern NO Ex Run Pattern 2 Go Preset gt 132 130 Deleting To delete Patterns enter into OSD menu Patterns Note When the system memorizes Patterns the commands are stored in the momories not the positions of Pan Tilt Zoom Hence there might be small differences between the original path and the revived path by path type of Patterns Note that it is not a problem in position precision 35 3 8 Group Function This function is that the camera memorizes the combination of Presets Pattern and or Swings sequently and runs Presets Pattern and or Swings repetitively MAX 8 sets of Group are programmable Each group can have MAX 20 actions which are the combination of Preset Pattern and Swing Preset speed can be set up and the repeat number of Pattern amp Swing can be set up in Group setup Dwell time between actions can be set up also D lai d attente Setting Groups To set Groups enter into OSD menu Running Method 1 Run Pattern Group NO 20 ex Run Group 7 lt Run Pattern gt 27 Groups Method 2 Go Preset gt Group NO 150 ex Run Group 7 Go Preset gt 157 Deleting To delete Groups enter into OSD menu Groups 36 LI legrand 3 9 Other Functions Power Up This setting defines a specific activity Preset Pattern Swing and Group to be performed in the Action event that the power to the camera is cycled This function enables the user to resume after
12. information refer to Reserved Presets Hot Keys in this manual Perfect Outdoor Environment Compatibility and Easy Installation 4305 23 4 305 24 4 305 25 The fans and heaters are built in in the camera for cold and hot temperature environment Also idealistic mechanical design protects the camera from water and dust IP67 when installed properly with wall mount bracket only LI legrand 1 3 Package Component 4 305 21 Model Product amp Accessories Main Body amp Surface Mount Bracket Default Accessories Main Cable Calblock Screws Tapping M4x16 Tapping M4x25 Machine M3x6 Machine M3x8 I O Cable 4 305 22 Model Product amp Accessories 2 Sd E Main Body Terminal Cover Dome Cover Screws Optional brackets In Ceiling Mount Bracket Ceiling Mount Bracket Corner bracket Wall mount bracket 4 305 96 4 305 97 4 305 98 4 305 94 4 305 23 4 305 24 4 305 25 Models Product amp Accessories Default Accessories Main Body amp Surface Mount Bracket Main Cable Wrench Accessories for The Models with Alarm In Out Wall Mount Bracket Function 1 0 Cable Screws Machine M5x15 Hex Lag 14x50 Optional Brackets Ceiling Mount Bracket 4 305 95 Pole bracket 4 305 99 10 Ll legrand 1 4 Main Part Description 4 305 21 Model Surface Mount Bracket Mounting Screw Hole Dome Cover Assembly Stud DIP Switch 6 Dome Cover Dom
13. the preset In the Edit Label menu the dark rectangular is the cursor As soon as finishing selecting an alphabet or a number the cursor moves to the next digit LE Position actuelle du curseur 1 With Left Right Up Down of the joystick move to a desired Alphabet or a desired number in the Alphanumeric set To select a desired Alphabet or a desired number press the NEAR key 1234567890 ABCDEFGHIJ KELMNOPOR ST Uwex wZabcd etghdijklmrn ip ia r ft a aN Espace Caract re d effacement arri re If you want to use a blank select the double quotation mark If you want to delete an Alphabet or a number use the back space character lt 2 If you complete the Label editing move the cursor to OK and press the NEAR key to save the completed label To abort the current change move the cursor to Cancel and press the NEAR key 51 Relay Out Setup 4 305 22 RELAY CWT PRESET e m mms omm o em en M RTE m oH o UR ES tT RES o Root ec eo RELAY GUT 1 OFF RELAY OUT 2 OFF Relay Out x ON OFF Sets Relay Outputs for assigned preset 52 Ll legrand BNN K K h _ lt amp q CiC i _ _Q amp amp NEE gt EXZ aA E lt X Xx _ T T SS 4 8 Swing Setup SWING SETUP deme cim SWING NO LST POS NOT USED ND POS NOT USED SWING SPEED CLEAR SWING CANCEL RUN SWING BACK EXIT Swing Number 1 8 Selects a Swing number to edi
14. 3 6 44 3mm 12X motorized day night dome colour camera 4 305 21 3 5 94 5 mm 27X motorized day night dome colour camera 4 305 22 3 6 44 3mm 12X weatherproof motorized day night dome colour camera 4 305 23 3 5 94 5 mm 27X weatherproof motorized day night dome colour camera 4 305 24 3 5 129 5 mm 37X weatherproof motorized day night dome colour camera 4305 25 t legrand 4 305 21 4 305 22 4 305 23 4 305 24 25 USER MANUAL LE03668AB Important Safety Guide Read heed and follow all the Instructions Read all the safety and operating instructions before using the product Keep this manual Keep this manual for reference in future Attachments Accessories Use only the attachments or accessories specified by the manufacturer Installation e Donotinstall near any heat resources such as radiators heat registers stoves or other appratus including amplifiers that product heat Improperly installed product may fall cause serious injury to a child or adult and damage the product e Do not block any ventilation holes or openings Install in accordance with the manufacturer s instructions e Use only with the cart stand tripod bracket mounting devices or table specified by the manufacturer e Installation should be done only by qualified personnel and conform to all the instructions by the manufacturer e Refer all servicing to qualified service personnel e Unless the product is specifically marked as IP67
15. CABLE RS 485 1C 1 0 CABLE CONTROLLER DVR SENSOR 1 0 am IR 4 DOOR SENSOR LA SWITCH Port Description e Main Cable Port Pin Number RJ45 Connector Wire Color 1 NENNEN BNC Connector wm e e OCable BEN NENNEN O Lo o 9 27 Power Description e Carefully check the voltage and current capacity of the rated power The rated power is indicated in the back of main unit 4 305 21 0 8 A DC 11V 15V 4 305 23 4 305 24 4 305 25 25A e For the DC input models be careful with the polarity of DC power The system should be permanentally damaged by wrong DC input e n case that the length of the power wire is very long there may be voltage drop and the syatem may not work properly Make the length of the power wire as short as possible RS 485 Communication e For PTZ control connect the cable s to your keyboard or DVR To connect multiple cameras to a single controller RS 485 communication should be connected in parallel as shown below If you are connecting a single camera to a controller terminate the camera When connecting more than one camera to a single controller terminate the last camera on the communication line The last camera means the camera farthest in cable length from the controller Note that the total length of the
16. Installation using Wall Mount Bracket 4 305 22 model CD Install Wall Mount Bracket on wall 2 Assemble Terminal Cover to Wall Mount Bracket with 3 screws Do not use Rubber Gasket Locate the summit of the Plate Spring at the arrow mark For more information refer to the Terminal Cover Assembling section 3 Connect Drop Prevention Spring to main 4 After assembling them screw main body to body to prevent camera from drop Line up the Terminal Cover to protect them from separation by mold lines and turn main body on its axis in vibration and so on CW Clockwise direction and assemble main body to Terminal Cover 24 LI legrand 2 8 Installation with Ceiling Mount Bracket 4 305 23 4 305 24 4 305 25 Models D Remove the ceiling tile from the ceiling and cut a hole whose diameter is 30 40mm on the ceiling tile to pass the wire s and cable s through to the upside of the ceiling In case of the wiring and cabling through the mounting surface only Then prepare the ceiling mount bracket Pull the wire s for the system as below Ancho Bolt 3 8 x70 3 Screw the dome cover to the main body and remove the protection vinyl from the dome cover Important Notice r 2 Pull the wire s and cable s for the system as below Wire the cable s to the ports Insert the mounting hooks into the holes on the surface of the main body and turn the main body Assemble the main both with the camera m
17. N Normal CLOSE Selects sensor operation type Action NOT USED PRESET PATTERN SWING GROUP Selects an action to run when a sensor signal is input 48 LI legrand e Hold Time Post Action ENDLESS 1 59 SEC 1 180 MIN Sets the time period for the action which is run by external sensor activation After the time period passes the action pre defined in Post Action runs seguentially in succession to the action by external sensor activation If this option is set to ENDLESS Post Action does not activate HOME PRESET PATTERN SWING GROUP PREV ACTION Selects the action that a camera will run after the time period in HOLD TIME passes If Post Action is set to PREV ACTION the camera runs the previous action which it ran most recently 49 NI 4 7 Preset Setup PRESET SETUP gt PRESET NO CLA PRESET EDIT SCENE EDIT LABEL LABEL123 RELAY OUT OFF CAM ADJUST GLOBAL Preset Number 14128 Selects a preset number to set up If a selected preset is already defined the camera moves to the pre defined position and preset parameters such as Label and CAM Adjust show on the monitor If a selected preset is not defined UNDEFINED shows on the monitor Clear Preset CANCEL OK Deletes the data of the selected Preset Edit Preset Scene Re defines the scene position of the selected Preset e Edit Preset Label Edits the label of the selected Preset to show on the
18. NE NONE NEAR EDIT ACT CANCEL NEAR EDIT CANCEL FAR EDIT END 1 Press Near key when the cursor is at NO to start editing the selected Group 2 Note that MAX 20 actions are allowed in a Group Move the cursor up down to select an Action Press Near key to edit 55 EDIT GROUP 1 3 Define Action Dwell time and Option Note that the dark rectangular is the cursor Move the cursor Left Right to select an item and move cursor Up Down to change each parameter Action NONE PRESET SWING PATTERN e DWELL O SEC 4 MIN Sets the Dwell Time between functions e OPT Option It is a preset speed when a preset is selected in the Action It is the number of repeat when a Pattern or a Swing is selected in the Action h MOVE CURSOR CANCEL A CHANGE VAL J 4 Edit the items such as Action Dwell and OPT by moving the cursor 1 PRESET 1 00 03 360 NONE NONE NON E NONE S No SAVE CANCEL EAR EDIT il 56 Ll legrand 5 After finishing editing a Action press Near key to go to the previous upper level menu Step Move the cursor Up Down to select an Action number and repeat Step 2 Step 4 to keep editing the selected Group GI ARAN BARRE S L F W SOSE S RPE ONESNO S SRR mum NUNG ONE PRESET 1 00 03 360 CANCEL 6 After finishing setting up press FAR key to exit Then the cursor will move to SAVE Press Nea
19. Privacy Zone Mask function is possible A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide Mask NO 1 8 Selects a Mask number to program If the selected mask has already data the camera moves as it was programmed Otherwise UNDEFINED will be displayed under the Mask number Display ON OFF Sets if the mask of the selected mask number shows or not on the screen Clear Mask CANCEL OK Deletes the mask data of the selected mask number 41 IU Privacy Zone Mask Area Setup EDIT MASK 1 S L en ns en SL GARI NHAC _ 4000690 HMM MIHI AAA MOVE TO TARGET POSITION Move your camera to an area to mask Then a mask and the menu to adjust the mask size will be displayed Privacy Zone Mask Size Setup EDIT MASK 1 il ns al abt ONU bl ies ab ADJUST MASK WIDTH Cav ADTUST MASK HEIGHT NEAR SAVE FAR CANCEL Adjusts the mask size Use the joystick or the arrow buttons of your controller to adjust mask size 4 gt Left Right Adjusts the mask width Up Down Adjusts the mask height 42 Ll legrand EU O O O O O I I AI II N O A I F I I I 4 5 Camera Setup Dome Camera Setup Menu ZOOM CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF SHARPNESS 16 WHITE BALANCE SETUP gt AUTO EXPOSURE SETUP Sets the general functions of zoom camera module
20. amount of pan from zero degree vertical the amount of tilt from zero degree horizontal and current compass direction Also identifies the amount of the zoom magnification Action Title ON OFF AUTO Identfies Actions SET PRESET xxx PRESET xxx PATTERN x SWG PRESET xxx UNDEFINED Preset Label ON OFF AUTO Displays the preset labels when the camera arrives at presets Alarm I O ON OFF AUTO Displays the activated alarms This information shows the current state of Alarm Inputs and Relay Outputs If an Input point is ON state it will show a number corresponding to each point If an Input point is OFF state will be displayed Example The point 2 amp 3 of inputs are ON and Output is ON OSD will show as below 40 Ll legrand E Ot OK OO oS Compass Direction setup MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL Move the camera to a target position and press NEAR button to save the direction as North The direction is the reference direction to assign other compass directions 4 4 Privacy Zone Mask Setup PRIVACY ZONE gt MASK NO 1 UNDEFINED DISPLAY OFF CLEAR MASK CANCEL EDIT MASK Privacy Zone Mask allows the user to program 4 rectangulars that can not be viewed by the operator of the system To protect privacy MAX 4 Privacy Masks can be created on the arbitrary position to hide objects such as windows shops or private house With the Spherical Coordinates system powerful
21. ange Auto Exposure Setup BA DAY NIGHT lt AUTOZ gt BRIGHTNESS 25 IRIS AUTO SHUTTER ESC AGC HIGH SSNR MIDDLE SENS UP lt AUTCO gt BACK e Backlight ON OFF Sets Backlight Compensation to ON OFF If a bright backlight is present the subjects in the picture may appear dark or as a silhouette Backlight compensation enhances objects in the center of the picture The camera uses the center of the picture to adjust the iris If there is a bright light source outside of this area it will wash out to white The camera will adjust the iris so that the object in the sensitive area is properly exposed e Day Night AUTO DAY NIGHT Sets Day amp Night mode You can increase sensitivity in low light conditions by switching to black white mode removing the IR cut filter or turning on DSS Color mode is preferred in normal lighting conditions The time to change a mode is 10 sec If this is set to DAY mode ACG is fixed to HIGH 44 LI legrand e Brightness 0 64 Adjusts the brightness of the images Iris The Shutter Speed and Gain are adjusted automatically in correspondence with each numeric value IRIS AUTO MANUAL 0 64 Sets Iris to operate automatically or at a user defined level If Iris is set to Auto Iris has higher priority in adjusting AE and Shutter Speed is fixed Auto iris is the lens function that automatically opens closes the iris in response to changing light conditions If I
22. assembling them screw main body to Terminal Cover to protect them from separation by vibration and so on 13 4 305 23 Model Mounting Screw Hole Mounting Hook DIP Switch Main Connector Sensor I O Port Dome Cover Main Body Terminal Cover Dome Cover Do not detach the protection vinyl from the dome cover before finishing all the installation process to protect the dome cover from scratches or dust DIP Switch Used to set up camera IDs and protocols Mounting Hook Used to assemble the main body with wall mount bracket or ceiling mount bracket Insert the mounting hooks into the holes on the surface of the main body and turn the main body Mounting Screw Hole Used to assemble the main body with a bracket with screws Main Connector Used for the power wire the video cable and the RS 485 communication cable connection Sensor I O Port Used for the sensor in out connection 14 LI legrand 2 INSTALLATION 2 1 DIP Switch Setup 4 305 21 4 305 23 4 305 24 4 305 25 models Before installing the camera set up the DIP switch to configure the camera ID and the communication protocol 4 305 22 model Before you install the camera you should set the DIP switches to configure the camera ID communication protocol Do not use the ISP connector Authorized person only ISP connector for System Upgrade Communication ON Refer io M Cinema com
23. ature LI legrand MECHANISM PART 360 Endless 360 sec 0 05 360 sec Proportional to Zoom 1 180 sec 127 Presets Label Independent Camera Parameter Setting 4 Patterns 1200 Commands Approx 5 Minute Pattern 8 Swings 8 Groups MAX 20 Actions with The Combination of Preset Pattern and Swing Auto Flip Auto Parking Power Up Action and etc RS 485 Pelco D Pelco P Selectable English Menu PTZ information etc 3 Inputs Photo Coupler Type DC 5V 12V 1 Output Relay Output MAX Load DC24V 1A AC125V 0 5A Always ON Operation Start from Internal Temperature 10 C 0 C 40 C 4 305 21 4 305 22 Models 30 C 50 C 4 305 23 4 305 24 4 305 25 Models RATED POWER 4 305 21 4 305 22 4 305 23 4 305 24 4 305 25 DC 12V 0 8A DC 12V 0 75 A DC 12V 2 5 A 63 MECHANICAL 4 305 21 Model Polycarbonate Material Polycarbonate ABS Polycarbonate 132 4x129 5 mm 132 4x187 5 mm 213 2x207 5 mm Weight kg Approx 0 7 Approx 0 8 Approx 0 85 kg MECHANICAL 4 305 23 Model 4 305 24 4 305 25 Models Polycarbonate Material Polycarbonate ABS 158 2x216 mm 274 5x227 3 mm 2192x265 3mm 296x276 6mm Weight kg Approx 2 6 kg Approx 2 8 kg Approx 3 2 kg Approx 3 8 kg 1 Specification and features are subject to change without prior notice 2 _ Specification and features are different by models 3 Check the voltage and current capacity of rated power carefully 64 LI legrand
24. communication cable between a controller and the camera s on the same communication line must be less than 1 2Km Keyb FT 28 Ll legrand E IHRE Video e Use BNC coaxial cable only Alarm Input Internal 45M 12V Before connecting sensors check driving voltages and output signal types of the sensors Since output signal types of the sensors are divided into Open Collector type and Voltage Output type in general the wiring must be done properly after considering IN COM The electric power source to drive input circuit Connect the wire of electric power source to drive the Sensors to this port as shown in the above those types circuit INT IN2 IN3 Connect the outputs of sensors to each port as shown in the above circuit If you want to use Alarm Input the types of sensors must be selected in OSD menu The sensor types are divided into Normal Open and Normal Close If wrong sensor types are selected alarms should be activated reversely to sensor inputs Normal Open Output Voltage is high state when sensor is activated Normal Close Output Voltage is high state when sensor is not activated Relay Output Internal AC or DE QUT 1 l mE B a ee M M M P LO AD AC or DC E ae m e 7 i UT 2 j i r LO AD The maximum loads are as follows 24 VDC 1A 29
25. e Cover Lock up Screw Dome Cover Assembly Stud DIP Switch 6 Surface Mount Bracket amp Mounting Screw Hole e Main Connector Sensor I O Port Main Connector I Qa Sensor I P Port Dome Cover Lock up Screw Dome Cover Do not detach the protection vinyl from the dome cover before finishing all the installation process to protect the dome cover from scratches or dust Used to lock up the dome cover after assembling the dome cover with the main body Used to line up the stud on the main body and the stud on the dome cover when assembling the dome cover with the main body Used to set up camera IDs and protocols Used for surface mount type wall mount type and ceiling mount type They are not used for in ceiling mount type Used for the power wire the video cable and the RS 485 communication cable connection Used for the sensor in out connection 11 UU 4 305 22 Model UE Loc loup Screw CD Mounting Hole Cabling Terminal Block _ Drop Prevention Spring fo EX Main Body Fuse se pre Drop Prevention Connector Hook Terminal Cover Dome Cover Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust Terminal Cover This is used to install the camera directly on the ceiling or attach to the other brackets such as in ceiling ceiling and wall mount After separating this cover firs
26. g the shortest path As a result the time to target view is remarkably short and the video on the monitor is very natural in monitoring LI legrand e With the Micro Stepping Control Technology the video looks very natural at high zoom magnification during a jog operation on a controller since the camera can be controlled by 0 05 sec Hence it is very easy to make the camera focus on desired target views at high zoom magnification Additionally it is easy to make the camera focus on desired positions with zoom proportional pan tilt movement Preset Pattern Swing Group Privacy Mask and More MAX 127 Presets are programmable and each preset can have its own parameter values independently from the other presets Foran example refer to the below table White Preset No Auto Exposure Label Balance Preset 1 Case A Cases 3 ENTRANCE MEE WAREHOUS RR E ee op pp eee MAX 4 Patterns are programmable This function is that the camera memorizes the path mostly curve path by the joystick of the controller and revives the trajectory operated by the joystick as closely as possible MAX 8 sets of Group are programmable This function is that the camera memorizes the combination of Presets Pattern and or Swings sequently and runs Presets Pattern and or Swings repetitively A Group can be combined upto 20 functions with any of Preset Pattern Swing 8 Privacy Masks are programmable not to intrude on any
27. heck Points before Operation e Before turning on the system check if the wire s and cable s are connected properly e Check if the camera ID on the controller is properly selected The camera ID must be identical to that of the target camera The camera ID can be checked by reading the DIP switch of the camera or on OSD e lf your controller supports multi protocols the protocol must be changed to match to that of the camera e Adjust the DIP switch after turning off the camera If you changed the camera protocol by changing the DIP S W the change will be effective after you reboot the camera e Since the operation method can be different by controllers refer to your controller manual if the camera can not be controlled properly The operation of this manual is based on the standard Pelco Controller 3 2 Check Points for Preset and Pattern Function before Operation e Check fully how to operate preset function and pattern function with your controller or DVR in advance to operate the camera functions when using a controller or a DVR e Refer to the following table when using standard Pelco protocol controllers lt Go Preset gt Input Preset Number and press Preset button shortly lt Set Preset gt Input Preset Number and keep pressing Preset button for more than 2 seconds lt Run Pattern gt Input Pattern Number and press Pattern button shortly lt Set Pattern gt Input Pattern Number and keep pressing Pa
28. me to get focuses The focus mode automatically changes to Auto Focus mode when jog operation starts 37 Xj 3 10 OSD Display tiquette du BEL12345 RESETIS Intitul de l acion pr r glage I 2 0 19 Informations d alarme ID de cam ra CAM 15 4 x1 N P T Z Information e P T Z Information Displays the amount of pan from zero degree vertical the amount of tilt from zero degree horizontal and current compass direction Also identifies the amount of the zoom magnification Camera ID Displays the selected Camera ID Address Action Title Identfies Actions SET PRESET xxx When Preset xxx is memorized PRESET xxx When the camera reaches Preset xxx PATTERN x When Pattern x is in action SWGx PRESET xxx When Swing x is in action Displays both of Swing number and Preset number UNDEFINED When a undefined function is called to run Preset Label Displays preset labels when the camera arrives at presets Alarm Information Displays activated alarms This information shows current state of Alarm Inputs and Relay Outputs If an Input point is ON state it will show a number corresponding to each point If an Input point is OFF state will be displayed Example The point 2 amp 3 of inputs are ON and Output is ON OSD will show as below 38 Ll legrand EE 4 OSD MENU 4 1 Quick Programming Guide e The menu items with lt gt always have sub menus e Togo to submen
29. monitor when the preset runs MAX 10 alphanuberic characteristics are allowed Relay Out Defines the relay output CAM Adjust GLOBAL LOCAL WB White Balance and AE Auto Exposure can be set up independently for each preset There are 2 modes Global mode amp Local mode The Global mode is that WB and or AE are is set up totally and simultaneously for all presets The Global parameter setup such as WB and AE can be done in ZDOM CAMERA SETUP menu The Local mode is that WB and or AE are is set up independently or separately for each preset The Local parameter setup for WB and AE can be done in each preset setup menu Each Local parameter such as WB and AE activates correspondingly when the camera arrives at each preset position During jog operation Global WB AE value should be applied All Local WB AE values do not change although Global WB AE value changes The Local mode has the prior to the Global mode Preset Scene Setup MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL 50 Ll legrand Toe o 1 Use the Joystick to move the camera to a desired position 0 2 Save the preset position by pressing NEAR key 0 3 Press FAR key to cancel targeting the preset position Preset Label Setup EDIT LABEL PRESET 1 ABCDEFGHIJ CANCEL apii gab afchijklmn opars tuvwx we CI f zos PARNE CPAP MAREE arr camem S cs Edit the label of the selected preset to show on the monitor when camera arrives at
30. more than IP67 or confirmed by the manufacturer it is designed for indoor use only and it must not be installed where exposed to rain and moisture e Do not load on the product e Use stainless steel hardware to fasten the mount e To prevent damage from water leakage when installing a mount outdoors on a roof or wall apply sealant properly around holes e These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other that contained in the operation instructions unless you are qualified to do so e Use only replacement parts specified by the manufacturer Power source This product should be operated only from the type of the power source indicated on the marking label LI legrand _ _ Was CAUTION Operating e Before using make sure that the power supply and others are properly installed e While operating if any abnormal condition or malfunction is observed stop using the product immediately and then contact your local dealer Handling e Do not disassemble or tamper with the parts inside the product e Do not drop or subject the product to shock and vibration as this can damage the product e Care must be taken when you clean the clear dome cover Especially scratch and dust will ruin the quality of the product Installation and Storage e Do not install the product in areas of extreme temperature which exceed the allowable range e
31. n its axis by 360 in CW Clockwise direction and then it turns back on its axis by 360 in CCW Counterclockwise direction The Swing speed is defined from 1 sec to 180 sec Setting Swings To set Swing enter into OSD menu Running Swings Method 1 lt Run Pattern gt Swing NO 10 ex Run Swing 3 Run Pattern 13 Method 2 Go Preset gt Swing NO 140 ex Run Swing 3 Go Preset gt 143 Deleting Swings To delete Swings enter into OSD menu 34 LI legrand 3 7 Pattern Function This function is that the camera memorizes the path mostly curve path by the joystick of the controller and revives the trajectory operated by joystick as closely as possible MAX 4 Patterns are programmable and Maximum 1200 communication commands can be programmed in a pattern Setting Patterns A Pattern can be created by the following methods Method 1 Set Pattern Pattern NO The Pattern programming window appears on the monitor as below NEAR SAVE FAR DELETE 0 0 x1 N The movement by Joystick and the preset movement can be memorized in a pattern After a pattern is programmed the remaining storage is displayed in progress bar on the screen To save the recording press NEAR key and to cancel press FAR key Method 2 Programming in OSD Menu See the section How to use OSD Menu Running Method 1 Run Pattern Pattern NO Ex Run Pattern 2 Run Pattern 2 Patterns Method 2 Go
32. nd screw on the dome cover lock up screw Then remove the protection vinyl from the dome cover Machine M3x6 Important Notice Before starting the installation make sure that the Camera ID and Protocol are set up properly When the pipe hole for wiring and cabling on side of the Surface Mount Bracket is not used make sure that the hole is properly sealed with the supplied Hole Plug 20 LI legrand EU 2 4 Direct Installation on the Ceiling 4 305 22 model D To pass cables to upside of ceiling please 2 For cable connection remove the pre defined hole mark on make about 50 60mm hole on the ceiling panel the Rubber Gasket and locate the summit of the Plate Spring at the arrow mark as shown in the dotted circle Rubber Casket After assembling the Rubber Gasket to 4 Connect the Drop Prevention Spring to the main body to the Terminal Cover install Terminal Cover on prevent camera from drop ceiling tex and connect cables to terminal blocks 5 Check the 2 mold line for assembly before Tighten the Lockup Screw as shown bellow starting assembly Line up the mold lines as shown in the dotted circle and turn main body on its axis in CW Clock Wise direction and assemble main body to Terminal Cover 21 2 5 Installation using In Ceiling Mount Bracket 4 305 22 model D Cut the panel of ceiling as shown bellow r 6170 7 DE T gg Hole Dimension mm 3 Locate the summit of the plate s
33. or private house With the Spherical Coordinates system powerful Privacy Zone Mask function is possible A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide GLOBAL LOCAL WB White Balance and AE Auto Exposure can be set up independently for each preset There are 2 modes Global mode amp Local mode The Global mode is that WB and or AE are is set up totally and simultaneously for all presets The Global parameter setup such as WB and AE can be done in ZOOM CAMERA SETUP menu The Local mode is that WB and or AE are is set up independently or separately for each preset The Local parameter setup for WB and AE can be done in each preset setup menu Each Local parameter such as WB and AE activates correspondingly when the camera arrives at each preset position During jog operation Global WB AE value should be applied All Local WB AE values do not change although Global WB AE value changes The Local mode has the prior to the Global mode Image Setup Semi Auto This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus Focus mode by operation Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation With Manual mode at presets Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as the camera arrives at presets It should shorten ti
34. other s privacy PTZ Pan Tilt Zoom Control With the RS 485 communication connection MAX 255 units of cameras can be connected to a single controller Pelco D or Pelco P protocols can be selected as a control protocol in the current firmware version OSD On Screen Display Menu OSD menu is provided to display the status of camera and to configure the functions interactively Theinformation such as Camera ID Pan Tilt Angle Direction Alarm Input and Preset is displayed on screen Alarm In Out Function 4305 22 4 alarm sensor inputs and 2 alarm output relays 4305 21 4 305 23 4 305 24 4 305 25 3 alarm sensor inputs and 1 alarm sensor outputs Alarm sensor input is decoupled with photo couplers to avoid external electric noise and shock perfectly Both of N O Normal Open sensors and N C Normal Close sensors can be used and the signal range of the sensor input is from DC 5 0V to 12 0V for various applications The camera can be set to move to a Preset position or to run functions such as Pattern Swing and Group when there are external sensor activations Also Post Alarm function is possible which is supposed to activate after user defined time period and sequentially in succession to the action by external sensor activations Reserved Presets Hot Keys Most camera setup options can be set up easily and directly with the reserved presets Hot Keys without entering into OSD menu For more
35. ount adaptor with the 3 screws Machine M5x15 Before starting the installation make sure that the Camera ID and Protocol are set up properly To adjust the installation height from the mounting surface the pipe and coupler should be needed between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling mount bracket Note that they are not supplied by the manufacturer 25 2 9 Installation with Wall Mount Bracket 4 305 23 4 305 24 4 305 25 Models D Make a hole whose diameter is 30 40mm on the 2 Pull the wire s and cable s for the system as mounting surface to pass the wire s and cable s through below Wire the cable s to the ports Insert the mounting the mounting surface In case of the wiring and cabling hooks into the holes on the surface of the main body and through the mounting surface only Then prepare the wall turn the main body Assemble the main both with the mount bracket Pull the wire s and cable s for the system camera mount adaptor with the 3 screws Machine M5x15 as below Attach the wall mount bracket to the mounting surface Hex Lag 14x50 3 Screw the dome cover to the main body and remove the protection vinyl from the dome cover Important Notice Before starting the installation make sure that the Camera ID and Protocol are set up properly 26 LI legrand 2 10 Wiring and Cabling 4 305 21 4 305 23 4 305 24 4 305 25 POWER MAIN
36. pring at the arrow mark as shown in the dotted circle e OE N G bo A O 69 gt paoeocd d 5 Screw camera to ceiling tex with 3 screws tightly 2 Assemble Terminal Cover of camera to the In Ceiling Mount Bracket as shown bellow 4 Assemble main body to Terminal Cover and insert the assembly into ceiling tex Holes are to be used to sustain the device 6 Assemble Deco Ring with camera and turn Deco Ring on its axis in CW Clockwise direction 22 LI legrand 2 6 D To pass cables to upside of ceiling please make about 50 60mm hole on the ceiling panel and attach the Ceiling mount bracket on it 3 Connect Drop Prevention Spring to main body to prevent camera from drop Line up the mold lines and turn main body on its axis in CW Clockwise direction and assemble main body to Terminal Cover D 9 W Installation using Ceiling Mount Bracket 4 305 22 model 2 Assemble Terminal Cover to Ceiling Mount Bracket with 3 screws Do not use Rubber Gasket Locate the summit of the Plate Spring at the arrow mark For more information refer to the Terminal Cover Assembling section 4 After assembling them screw main body to Terminal Cover to protect them from separation by vibration and so on 23 2 7
37. r key to save the data 57 4 11 System Initialization CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET SCLR MOTION SET CLH EDIT DATA e Clear All Data Deletes all configuration data an e Clear Display Set Initializes all the configuration data for Display Clear Camera Set Initializes all the configuration data for Camera e Clear Motion Set Initializes all the configuration data for Motion e Clear Edit Data Deletes all the configuration data for Preset Swing Pattern and Group Reboot Camera Reboots the zoom camera module Reboot System Reboots the system 58 LI legrand Oona Factory Default 6 Display Parameters Camera Parameters Camera ID Focus Mode SemiAuto PTZ Information Digital Zoom ON Action Title Image Flip Preset Label Sharpness Stabilization White Balance Alarm I O AUTO North Direction Pan 0 Backlight Day amp Night Privacy Zone Undefined Brightness Iris Shutter e Motion Parameters AGC Motion Lock SSNR MIDDLE Power Up Action ON SENS UP AUTO 4 Frame Auto Flip ON Jog Max Speed 120 sec 6 User Defined Data Preset 1 128 Undefined Jog Direction INVERSE Freeze In Preset OFF Swing 1 8 Undefined Park Action OFF Pattern 1 4 Undefined Alarm Action OFF Group 1 8 Undefined 59 5 Specifications CAMERA PART 4 305 21 4 305 23 560 TV Lines Color 600 TV Lines B W 12x Optical Zoom 12x Digital Zoom FL6 Wide F2 0 Tele
38. reset movement As soon as camera stops at preset end point camera starts displaying live images which it gets at the end preset point This feature also reduces bandwidth when working with digital systems or digital network systems This function availability should be different by models 47 Parking Action Setup PARKING ACTION SETUP PARK ENABLE WAIT TIME PARK ACTION This feature allows the camera to begin a specified action after a programmed time of inactivity Park Enable ON OFF If Park Enable is set to ON the camera runs an assigned function automatically if there is no PTZ command during the programmed Wait Time e Wait Time 1 59 sec 1 180 min Wait Time can be programmed from 1 second to 180 minutes Park Action HOME PRESET PATTERN SWING GROUP PREV ACTION This feature defines the activity when the camera parks If Park Action is set to HOME the camera moves to the home position which is memorized when the system boots If Park Action is set to PREV ACTION the camera runs the previous action which it ran most recently Alarm Input Setup ALARM INPUT SETUP ywr emen ome ee ME cem ALARM NO 1 TYPE N OPER ACTION NOT USED HOLD TIME ENDLESS POST ACTION HOME Defines Alarm Function When an alarm is receive an input signal to the camera triggers the user defined action programmed for the alarm Alarm No 1 3 Selects a sensor number to set up Type Normal OPE
39. ris is set to Manual Iris is fixed and Iris has lower priority in adjusting AE in comparison with others The Iris level range is O 100 e Shutter Speed A Flicker Manual 1 60 50 1 10000 sec Sets Shutter Speed Shutter Speed is the duration of the electronic shutter If Iris is set to Manual and Shutter Speed is set to ESC Shutter Speed has higher priority If Shutter Speed is set to A Flicker to remove Flicker Shutter Soeed should be set to 1 100 sec for NTSC and 1 120 for PAL e AGC OFF LOW HIGH Sets AGC This setting enhances image brightness automatically in case that luminance level of image signal is too low SSNR OFF LOW MIDDLE HIGH Sets SSNR This setting enhances the images by deducting noises when the gain level of the mages is too high SENS UP AUTO 2 256 OFF Sets SENS UP This setting activates Slow Shutter function when luminance of image signal is too dark It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function Wide Dynamic Range Setup mic LIMIT MIODE E LEWEL 0 e Limit LOW MIDDLE HIGH Level 0 100 45 U HLC High Light Compensation Setup e Limit AUTO MANUAL When there are too bright lights this function blocks light sources on the images to have better images For example when there is a car coming to a camera at night this function bocks car headlights to recognize its number plate Level 0 10
40. rm can be activated reversely 18 Ll legrand A 2 2 In Ceiling Mount Installation 4 305 21 Model D Remove the ceiling tile from the ceiling and cut a D Connect the wiring and cabling and attach the hole whose diameter is 110mm on the ceiling tile to pass camera to the ceiling tile Tapping M4x16 the wires and cables through to the upside of ceiling 3 Align the dome cover stud with the dome cover 4 Turn the dome cover clockwise and screw on the assembly stud and slightly push the dome cover to the dome cover lock up screw Then remove the protection ceiling tile vinyl from the dome cover Machine M3x6 Important Notice Before starting the installation make sure that the Camera ID and Protocol are set up properly 19 2 3 Installation with Surface Mount Bracket 4 305 21 Model D Remove the ceiling tile from the ceiling and 2 Prepare the surface mount bracket Pull the wires and cut a hole whose diameter is 30 40mm on the ceiling cables for the system as below Attach the surface mount tile to pass the wires and cables through to the upside bracket to the mounting surface Tapping M4x25 of the ceiling In case of wiring and cabling through the ceiling tile only lt 3 Connect the wires and cables to the ports and 4 Align the dome cover stud with the dome cover install the main body Machine M3x8 assembly stud and slightly push the dome cover to the ceiling Turn the dome cover clockwise a
41. t If the selected Swing is not defined NOT USED is displayed in the 1st Position and the 2nd Position e 1st Position PRESET 1 128 2nd Position Sets the 2 positions for a Swing function If the selected preset is not defined UNDEFINED is displayed as shown below SWING SETUP SWING NO LST POS ino POS When a swing function runs the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise direction Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW Counterclockwise direction In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same or only 1 Preset position is assigned the camera turns on its axis by 360 in CW direction and then it turns on its axis by 360 in CCW direction Swing Speed 1 sec 180 sec Defines Swing speed between the 2 Preset positions from 1 sec to 180 sec e Clear Swing CANCEL OK Deletes the data of the selected Swing Run Swing Runs Swing for the test purposes to check if it works properly 53 4 9 Pattern Setup FATTERN SETUP PATTERN NO UNDEFINED CLR PATTERN CANCEL RUN PATTERN lt PDIT PATTERNS Pattern Number 1 4 Selects a Pattern number to edit If the selected pattern number is not defined UNDEFINED will be displayed under the selected pattern number Clear Pattern CANCEL OK
42. t and then attach this directly to ceiling or to the other bracket Camera must be assembled at the last stage Drop Prevention Spring This part keeps the camera from dropping during installation and maintenance After install the Terminal Cover please hang the spring to the drop prevention hook of main body as shown in picture for further tasks Drop Prevention Hook e Lockup Screw After assembling Terminal Cover to main body screw Terminal Cover to main body to protect them from separation by vibration and so on e Fuse If the fuse is burnt to protect your came from over current damage the fuse have to be replace with new one The fuse specification is 250V 2A However we recommend consulting with supplier to remove the cause of over current Cabling Terminal Block During installation Power Video Communication Alarm 1 0 cables are connected on to this cabling terminal block 12 Ll legrand Terminal Cover Disassembling D Remove the Lockup Screw as shown bellow 2 Turn main body on its axis in CCW Counter clockwise direction and separate it from Terminal Cover Terminal Cover Assembling D Check if the summit of the Plate Spring is 2 Checkthe 2 mold line for assembly before located at the arrow mark as shown in the dotted starting assembly Line up the mold lines as circle shown in the dotted circle and turn main body on its axis in CW Clockwise direction and assemble main body to Terminal Cover After
43. t Mode to DAY Setting OSD Display Mode to AUTO Except Privacy Mask Setting OSD Display Mode to OFF Except Privacy Mask Setting OSD Display Mode to ON Except Privacy Mask Setting all Privacy Mask Display to OFF Setting all Privacy Mask Display to ON 33 3 5 Preset Function MAX 127 positions are programmable The Preset number can be assigned from 1 to 128 except 95 Preset 95 is reserved for entering into OSD menu Camera parameters such as White Balance Auto Exposure and others can be set up independently and each preset can have its own parameter values independently from the other persets When setting up presets with a controller Label should be blank and Camera Adjust should be set to GLOBAL as the default To change the parameters enter into OSD menu Setting Presets Set Preset 1 128 Running Presets Go Preset 1 128 Deleting Presets To delete Presets enter into OSD menu 3 6 Swing Function This function is that the camera moves repetitively between two preset positions at programmed speeds When a swing function runs the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise direction Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW Counterclockwise direction In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same the camera turns o
44. tor Setup Terminal resistor is used if your system is one of following two cases e Case1 Control cable between camera and controller is relatively very long 1 1 connection If communication cable is very long the electrical signal will bound in the terminal point This reflected signal cause distortion of original signal Accordingly the camera can be out of control In this case the terminal resistor of both sides i e camera and controller must be set to ON state e Case2 Multiple cameras are controlled at the same time Due to similar reasons with case 1 the terminal resisters of controller and the last camera must be set to ON state Last camera means decided by cable length Do not turn on the terminal resistor of all cameras Terminal Resstor Terminal Resistor Terminal Resistor OFF OFF ON 17 Sensor Type Setup e lf you want to use Alarm Input the types of sensor must be selected The sensor types are Normal Open and Normal Normal Open Output Voltage is high state when sensor is activated Normal Close Output Voltage is high state when sensor is not activated Sensor 1 Normal Close Type ST1 Pin 4 Sensor 1 Normal Open Type Sensor 2 Normal Close Type ST2 Pin 5 Sensor 2 Normal Open Type Sensor 3 Normal Close Type ST3 Pin 6 Sensor 3 Normal Open Type Sensor 4 Normal Close Type STA Pin 7 Sensor 4 Normal Open Type e f sensor type is not selected properly the ala
45. ttern button for more than 2 seconds e If your controller or DVR has no pattern button or function use the Hot Keys with preset numbers For more information refer to Reserved Presets Hot Keys in this manual 32 LI legrand 3 3 OSD Menu Function With OSD menu the system can be properly configured for each application Entering into OSD Go Preset 95 3 4 Reserved Presets Hot Keys Description Some Preset numbers are reserved to change some parameters without entering into OSD menu Hot Keys Go Preset 95 Entering into OSD menu Go Preset 131 134 Running Pattern Function 1 4 Go Preset 141 148 Running Swing Function 1 8 Go Preset 151 158 Running Group Function 1 8 Go Preset 161 Set Preset 161 Go Preset 167 Set Preset 167 Go Preset 170 Go Preset 171 Go Preset 174 Go Preset 175 Go Preset 176 Go Preset 177 Go Preset 178 Go Preset 179 Go Preset 190 Go Preset 191 Go Preset 192 Go Preset 193 Go Preset 194 Turning off Relay Output Turning on Relay Output Setting Zoom Proportional Function to ON Setting Zoom Proportional Function to OFF Setting Camera BLC Mode to OFF Setting Camera BLC Mode to ON Setting Camera Focus Mode to AUTO Setting Camera Focus Mode to Manual Setting Camera Focus Mode to SEMI AUTO Setting Day amp Night Mode to AUTO Setting Day amp Night Mode to NIGHT Setting Day amp Nigh
46. turning on power the last action being executed before turning off the power Most of actions such as Preset Pattern Swing and Group are available for this function but Jog actions are not available to resume Auto Flip In case that tilt angle arrives at the top of tilt orbit 90 zoom module camera turns on its axis by 180 at the top of tilt orbit and moves to opposite tilt direction 180 to keep tracing targets amp Parking Action This feature allows the camera to begin a specified operation after a programmed time of inactivity This function makes the camera automatically run a pre defined action if there is no command from controller for a pre defined time period Wait Time means how long a camera should wait for from the previous last most recent command before running the pre defined action It can be set to 1 second 3 hours Alarm Input 3 Alarm Inputs are available When external sensors activate the camera runs pre defined actions such as Preset Pattern Swing and Group After the pre defined time period passed Post Alarm activates which is pre defined Note that only the latest alarm input is effective when multiple sensors are activated at the same time Privacy Zone Privacy Zone Mask allows the user to program 8 rectangulars that can not be viewed by the Mask operator of the system To protect others privacy MAX 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows shops
47. us or make the cursor move to the right press NEAR key e Togo to the previous upper level menus press FAR key e To make a selection press NEAR key e To cancel a selection press FAR key e To move the cursor in the menu use the joystick to the Up Down direction or Left Right direction e To change a value of an item use Up Down of the joystick in the controller e To save changes press NEAR key e To cancel changes press FAR key 4 2 Main Menu SPEED DOME CAMERA lt SYSTEM INFORMATION DISPLAY SETUP System Information Displays the system information and configuration The system setting can not be changed using the OSD menu and the information is for reference only e Display Setup Enables the user to program how labels are displayed on the monitor Dome Camera Setup Enables the user to configure various functions of the camera System Initialize Initializes all system configurations and all data to the factory default parameters 39 lll 4 3 Display setup DISPLAY SETUP FTZ INFORMATION AUTO ACTION TITLE AUTO PRESET LABEL AUTO ALARM I O AUTO SET NORTH DIRECTION PRIVACY ZONE Display setup allows you to program how labels are displayed on the monitor In case of AUTO the labels are displayed on the monitor when there are any changes in parameters Camera ID ON OFF Displays the selected Camera ID Address e PTZ Information ON OFF AUTO Displays the

USER MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents