QBOX Manual
Contents
1. GENERATION AHEAD www q box tv Qbox one Quick User Manual Digital satellite receiver for free and encrypted Digital Video Broadcasting DVB Communication Port Internal hard disk support Two Smartcard Readers Linux OS For Full User Manual please refer to www q box tv The QBox one carries the CE Sign and fulfills all requirements from the EU software Release 1 5 2 on 15 09 2008 Subject to change without prior notification Before initial operation on the receiver Safety instructions Please read the safety instructions completely and carefully before using the Q Box The Manufacturer takes no responsibility for damages as a result of incorrect handling of the QBox The safety marking is located on the exterior of the bottom of the apparatus The mains plug shall be installed near the equipment and shall remain readily operable Allow enough space around the QBox for sufficient ventilation Do not cover the top of the QBox and allow enough space to other devices The louvers of the devices must be free at all times to allow sufficient heat transfer from inside the device Never put vases or any other liquid filled containers on top of the device Do not expose the device to dripping or splashing liquids Do not place open flame sources such as lit candles on top of the device The device may only be operated in moderate climate Do not remove the cover Risk of electric shock If it is necessary2. If your QBox is Frequency 177 50 MHz provided with DVB T tuner please check out your system configuration it will start scanning the pre installed frequencies of Terrestrial Transponders If some services are not found you can either do a Manual Frequency Scan As it will follow on the next slide Once the Scan is completed a Scan report will show up Manual Terrestrial Transponder Scan With this function you can manually scan each Satellite ki Terrestrial specific frequency in case the j automatic scan will skip it or it is simply not listed Frequency 128 2 8 2 fats MHz Inv Enter the Menu button Polarity vertical vertical FEC 3 4 Setup lt OK gt Symbol Rate 080 80 0 gt KSymb s Service Searching lt OK gt Manual Transponder Scan lt OK gt SNR oye 5B AGC ft 595 Move with the Remote Control over the frequency BER 355 and set the first 2 digits to 12 and on the other 3 LOCK v SYNC digits set the frequency you want to scan like in Leo the example 826 use ONIT use BAT Set the Symbol rate to 00800 this will tell the STB only Free network search to set the terrestrial tuner Let all the other settings as is start scan start scan enter pids enter pids Press lt Start Scan gt button choose wished satellite wished satellite ok pe Must be 12 Frequency to scan in Mhz Set to 00800 for Terrestrial Scan G Find Terrestrial Channels Com
3. grounded The grounding system must meet SABS 061 requirements Cleaning Disconnect the mains power cord before cleaning the cover Use a slightly damp cloth without cleaning agents Connect the QBox only to suitable sockets Do not allow overloads to occur Please be careful that the batteries of your remote control are not exposed to heat since they might explode Disposal instructions The packaging of the QBox only consists of reusable materials Please recycle if possible This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product Please note that empty batteries and electric waste is not to be put into the regular garbage CE Certification Duolabs S p A declares that this equipment complies to essential requisites and other relevant provisions of Dire
4. is the Mhz step by which the Blind Scan will scan for Transponders Please mid that as big as the step will be Max 15Mhz at faster the search will be as less channels it can be possibly detect Once you are done with the settings you can e Start Scan e Stop Scan e Erase All Feeds e Check the signal strength When you finished scanning all the found channels will be stored in Feeds favorite folder and in the Main Channels List folder Once you press the Erase All Feeds button all channels will be erased from the Feeds folder and the Main Channels List folder Quick user guide GENERATION AHEAD www q box tv All rights reserved
5. to open the device please contact a trained professional Do not put any metal things into the slots or ventilation openings The installation of a hard disk is only allowed by skilled personal or your local dealer A A RISK OF ELECTRIC SHOCK DO NOT OPEN A Modifications and changes to the QBox lead to loss of warranty if not performed and documented by skilled personal We recommend the installation of a hard disk by your local dealer Unskilled installation of a hard disk leads to loss of warranty Shut down In case your QBox is not in use for a long period of time disconnect the power plug from the power outlet During thunder storm the unit should also be physically disconnected from the power outlet Additional safety instructions Dis Connecting to a LNB Turn the QBox off before you connect or disconnect a cable coming from or going to a LNB Connecting to a TV Before connecting or disconnecting your QBox to from a TV please turn it off In case you notice any damage to the power cord or power plug immediately disconnect the device from the power outlet In case the device was exposed to humidity immediately disconnect the device from the power outlet In case you notice any serious damage to the outer shell of the device immediately disconnect the device from the power outlet Do not expose the QBox to direct sunlight lightning or rain Grounding The LNB cable must be
6. Standby LED The Standby LED lights up red if the QBox is in standby mode It lights up green if the QBox is powered on Remote Control RC Led The remote control LED lights up every time the QBox receives a signal from the remote control Standby on off USB Port The USB port will handle the PVR and other functions In this port you can insert only USB compatible devices such as PEN sticks or USB Hard Disks Explanation Rear Panel Video output FBAS You can optionally connect your QBox to a TV using a RCA Chinch cable Composite Audio output analog Cinch Connect your QBox with a RCA Cinch cable to your HiFi Amplifier e g AUX In or Tape In ports Serial interface RS232C Sub D 9 pin The Serial Port is used to update the operating system Please connect a serial null modem cable here TV Scart Connect your TV or beamer to your QBox using a Scart cable Audio output SPDIF digital Toslink You can connect your Qbox with an optical Toslink cable to your HiFi Amplifier or DSP The AC3 signal is also available at this port in case the selected channel transmits Dolby Digital signals Power supply connector Plug the power cable of the power supply that came with your QBox into power outlet Connect your power supply to your Qbox You must not connect the power plug of the power supply to anything other than a socket that supplies 230V 50Hz Network interface Ethernet 10 100Mbit RJ45 The Communication Port is an Ether
7. control All Menus and Service DUOLABS lists are closed with the EXIT Button Menu Button If you are in TV or RADIO Mode pressing this button will bring up the OSD main menu The OSD main menu has the following options 1 TV Mode You can switch to the needed option by pressing the Navigation Buttons left or right Also see Important notes about operation The numbers in front of each option can be used to directly access the needed function by pressing the according number on the Numeric Keypad of your Remote control If you are in the service list pressing the MENU Button brings up the service menu The shown options may vary depending on the service list you selected The Power Button switches your QBox on and off See chapter Turning your Qbox on and off The TV Mode Button switches your remote control into TV control mode to control your preprogrammed TV It will shortly light up once your press the button See chapter TV Mode setup Enter a service number to directly access the option by using the Numeric Keypad The service numbers are on the left side of the service list The Numeric Keypad can also be used to enter the teletext page number when you are in TV Control Mode and if your TV is teletext capable The TV station has to submit teletext information otherwise this feature cannot be used Pressing the MUTE Button mutes the Volume A crossed speaker symbol will appear on the TV screen Pressing it again or p
8. ctives 2006 95 CE low voltage e 89 336 CE electromagnetic compatibility For Wi Fi sold models Duolabs S p A Declares that this equipment complies to essential requisites and other relevant provisions of Directive 1999 5 CE Radio and Telecommunications Terminal Equipments The declaration of conformity may be required to Duolabs S p A via Baggi 28 36061 Bassano del Grappa VI The use of the radio interface may be subjected to local restriction of use Customers are responsible for verifying approval for use in their individual countries Please consult your local spectrum authority http ec europa eu enterprise rtte spectr hntm Packaging contents Please check the completeness of the box s contents Included in box Qbox One Batteries 1 5V Mignon Remote Control AA LR6 Power Cord Power Supply 12Volts 1 IDE Cable already installed inside the device 1 User manual Front View Satellite Antenna Input Output Rear View Smartcard Readers USB Port Terrestrial Antenna Scart Input amp VCR Input Output Output Video Audio Power Supply USB Port Output VIDEO N Ae 9 AUDIO r j R LI ETHERNET 5232 SPDIF RESET OG 12V Digital Audio Output Power Supply Ethernet Communication Input Explanation Front Panel Double Smartcard Reader Insert your Smartcard with the golden chip facing down and forward into the Smartcard reader
9. e you to the FILE Mode Pressing the HELP Button activates the Help menu Installation Turning the device on Turning the device on Insert 2 AA 1 5V batteries taking care to observe the and markings indicated inside into the remote control Before using the QBox please read the safety instructions Connect the LNB or antenna with a coaxial cable to LNB or Antenna In at your QBox Connect the QBox with a Scart cable to your television screen Plug in the power cable into a 230V 50Hz power socket If you are using a switchable power socket please shutdown your QBox into deep standby before switching off the power socket If you switch on your QBox for the first time you will see the setup wizard The setup wizard will guide you through the first time installation You will be asked for your TV standard the regional settings and your language Please choose and follow the instructions on the screen Please note that the video format meets the factory setting CVBS FBAS From here on please follow the instructions on the screen For some special features regarding the non standard ENIGMA functions please refer to the appendix on this user guide For full detailed information refer to the full User Manual Downloadable from the official QBox web site www q box tv Appendix 1 Dedicated Functions for QBox To get access to some special functions of your QBox you need to enter the Plug In menu by press
10. ing the blue button on your Remote Control Plug In button a Plugins Giochi e Televideo QBOX Manager Teletext TuxBox Commander Choose QBox manager and press OK start Ngrab recording stop Ngrab recording QBox Manager Functions QBOX Manager plugin v1 6 Remove HDD This function is needed to change the HDD for PVR from Internal HDD to External HDD or vice versa You need to install the previously installed driver and install the other one you want to use Use External HDD on USB Use Internal HDD This function is needed to mount the Arps att ajz internal HDD for PVR You need to run Remove HDD Find Terrestrial Channels function in case you have had previously installed the Configure WiFi External HDD on USB Create Backup to USB Use External HDD on USB This function is needed to Restore Backup from USB mount the External HDD for PVR You need to run Remove A a HDD function in case you have had previously installed the Blind Scan Internal HDD Create Backup to USB This function will create a backup file of your system configuration into a USB Pen or external HDD Abort move selection Restore Backup from USB This function will restore a backup file of your system configuration from a USB Pen or external HDD Other functions will be explained on the next pages Terrestrial Scan Setup r Find Terrestrial Channels Scan Transponder 1 68 Find Terrestrial Channels
11. net port It is used to communicate with your QBox via HTTP FTP NFS Telnet and Samba This port is also used to update the operating system of your QBox Please use a regular patch cable to connect your QBox to your LAN The factory set username and password to get access to the QBox are Username root Password qboxqbox USB Port The USB port will handle the PVR and other functions In this port you can insert only USB compatible devices such as PEN sticks or USB Hard Disks Important notes about operation All functions of the QBox can be controlled via OSD Menu On Screen Display This makes the handling of the QBox very easy for you All options are indicated by four colored dots or beams red green yellow blue in the OSD Menu and can be started with the Option Buttons on the Remote Control Depending on the chosen Menu these options do change The Options Buttons of your remote control have multiple functions You will notice control symbols below the four colored Options Buttons the TV and the RADIO Button In PVR Mode these buttons are used to control the digital recording according to their symbols Pressing the VIDEO Button on your remote control will activate the PVR Mode The Infobar will also indicate this It changes from showing the channel information to showing the control symbols for the PVR Mode also see Instant recording In general the menus are controlled using the Navigation Buttons on your remote
12. ocols configuration e None No Encryption e WEP 64 WEP128 WEP Encryption 64 or 128 bit WEP 64bit HEX Sbyte WEP 128bit HEX 13 byte e WPA PSK TKIP WPA encryption WPA min 8 max 63 ASCII chars e WPA2 PSK CCMP AES WPA2 encryption WPA2 min 8 max 63 ASCII chars WIFI Encryption Settings Encryption Mode Scan SSID WPA2 PSK CCMP AES 2516 Insert Pairwise Key insert key Save Settings Encryption Exit Save Settings Please make sure you enter the correct encryption keyset matching with the same keyset in your Router or Access Point Blind Scan Function Blind Scan Manager Satellite Ol Hotbird 13 0E Start Frequency MHz 07 0 0 End Frequency MHz 2 7 5 0 Step Frequency 4MHz 4 MHz Scan St 5 MHz MHz Current Frequency MF 15 MHz SNR LINK Blind Scan Manager Satellite Ol Hotbird 13 0E Start Frequency MHz 0700 End Frequency MHz 2 7 5 0 Step Frequency 4MHz Scan Stop Erase All Feeds Current Frequency MHz SNR LINK What s Blind Scan Blind Scan is a special function which allows the user to scan in a blind way for hidden temporary satellite feeds This function is in QBox hardware performed How to get started Choose Blind Scan from the QBox manager and then set the following parameters e Start Frequency Range must start from 10 700 Mhz e End Frequency Range must end at 12 750 Mhz e Step Frequency This
13. plete _ The transponder scan has finished and found 2 Transponders with 34 Services Scan Completed scanned You can find your terrestrial channels in When the scan will be completed a report of Bouquets gt Terrestrial found channels will be prompted on the screen Press OK to continue Wi Fi connection Setup Configure WIFI Interface i Enable Wifi Interface Addressing Type Save Settings e Encryption Ext Configure WIFI Interface Enable Wifi Interface Scan SSID Addressing Type STATICIP iP O O Encryption Exit Save Settings WIFI Encryption Settings Scan SSID None ls None WEP64 WEPI28 WPA PSK TKIP WPA2 PSK CCMP AES Save Settings ExiG Encryption Mode Encryption Exit Save Settings Configure WiFi If your QBox is provided with Wi Fi module please check out your system configuration you need to enable the Wi Fi interface simply pressing on Enable Wifi Interface area And the new menu will appear Configure WiFi Once you Enable Wifi Interface it will come up with the possible options for IP configuration You can choose between a Static IP or a Dynamic IP Scan SSID This function will scan the WiFi Access Point in the area It will show up the found services in the box Encryption Once you enabled the Encryption WiFi interface You will be prompted with the possible options for Security Encryption prot
14. ressing one of the Volume Buttons brings back the audio You can leave all menus and service lists by pressing the EXIT Button By pressing the OK Button you confirm a selection in the menu or service list navigation If no OSD menu is present on your screen the infobar is shown once you press the OK Button In general the menus are controlled using the Navigation Buttons on your remote control To get into a submenu you have to press the OK Button The Volume Buttons control the volume of the audio Pressing will make turn it up and pressing will turn it down By pressing the AUDIO Button you can choose the different audio tracks offered by the station Pressing the VIDEO Button activates the PVR Mode The Infobar will show the control symbols You can instantly start recording by pressing the Radio Button on your remote control You can also toggle between single double and trible column view in the service list All possible options are shown by the four colored dots blocks red green yellow blue and can be activated by the Options Buttons In PVR Mode these buttons are used to control the digital recording Depending on the menu you currently are in the options will change and will be named differently Pressing the TV Button activates the TV Mode Pressing the RADIO Button activates the RADIO Mode The TEXT Button activates the Teletext TuxTxt If you are in the stations list pressing this button will directly tak
Download Pdf Manuals
Related Search