to the Digital Dash User Manual
Contents
1. DASH Instruction Manual Potenza Sports Cars Limited 2007 Version 3 2 Introduction Congratulations on your purchase of a DASH2 display unit for Westfield sports cars This is an advanced feature packed display system designed to be compact robust and water resistant Make sure that you follow this instruction manual to ensure correct installation and operation and the DASH2 should provide you with many years of trouble free service You should begin by installing the provided software onto your PC The CD contains the DASH2 configuration program and the Online Help System After installation the Help System is accessible under the heading Documentation Start Program Files Dash If you encounter any problems with the installation and operation of your DASH2 please refer to the Online Help System in the first instance Wiring the DASH2 to your Westfield has been simplified by a colour coded loom Please follow the installation guidelines carefully These will take you through the wiring and configuration of your DASH2 Contents INCFOGUEHO Misia 2 CONS asili 3 ASF ZINC re NEY OU aaacasa 5 Whats N the BOX rici na 6 Installino the DASH ceainaria aa aiaa 6 Physical installation of the Display UNIt rr 6 Electrical Installato iaia 6 SWEMU save dnw acta netcsstsentacatatatasenatateectenstarsestatacubasatdrslnsetcretstatasabatatdechatatvecbersteveeras 7 Step by Step Installation Guide ecicintcvnicucesr2. configured to perform the reset function To set up a button to do this see the section Programming soft buttons and assign a button to the Trip reset function When this button is pressed in normal display mode the bottom section of the display will then read trip reset Press any button to return to normal display mode with the trip meter reading zero Configuring and changing the brightness of the shift lights Configuration of the shift lights is carried out in the DASH2 configuration software under the RPM setup tab The engine speeds at which the LEDs illuminate are set by first entering a value for RPM of final shift light This is the engine speed at which all 6 LEDs will flash and would typically be set to the maximum permissible engine speed The engine speed interval between illumination of each shift light 1 2 3 4 5 6 6 flashing is then defined by entering the engine speed interval in the Shift light interval field The brightness of the shift lights is controlled from the DASH2 itself The sidelight input to the DASH2 is used to detect when the vehicle lights are turned on and dim the shift lights and indicator lights accordingly The brightness of the shift lights at both high and low settings can be altered by the user to suit personal preference To do this go to LED brightness and press SELECT The shift lights will then be illuminated at the current high brightness setting The UP and DOWN b
3. AA A ara 18 Resettingithe trip Meer anandia eran ira rta ea 18 Configuring and changing the brightness of the Shift lIGNIS 18 Setting warning and sector display times ii 19 Lap timing on the DASH sarai 19 Adding track markers from the DASH2 or DL1 DL2 eee eeeeaeeeeesaeeeeeeaeeeeaes 19 Adding track markers from the Analysis Software ria 20 Using lap marker files WIth Ihe DASH tices rana 20 L ap umino 0perdioRsa ac 20 Predictive lap TIMES ci catvccnatetuechenstatutabatcousanatdectebetatateretacatatatdsstenstdneteiatusstatatesutaitueckes 21 Using target marker and sector tiMmes 21 Copying current lap sector times tO Memory ii 21 EGItIng targetlap Sectortimesa aaa 21 Using target marker sector tiMes rr 22 Resllashingithe DASH 22 Appendix I DASH2 Direct Pinout aaa 23 DASH CONMNECHON NOLES vorivirkrirevirivireririvieVin ini 25 Indicators hazard Warning INS canarie 25 Main beam warning Igt 25 Brake WakMINGH IGM assasanasent cede vedevatacatecatasad Taen TNEI PCAN EUN RENTAN PUNCTAT ETAN TONAN TiN 25 FOG NONE WANING sioni dii iii 25 Alternator charge Warniibiaianteaniaae ae 25 olele aaria eE Ar E E EREA ATE EEE 25 Wheel SPEC MPU ruia en T TE TOT ea 25 Engine speed nputercaiscraiiiai aa AAEE A 26 PMGIOGUC IADU sae iii 26 Connection to a Race Technology data IoggeEr i 27 DASHe General Layout Rev counter scale Rev count
4. buttons please note that the wire colours on the connectors correspond to the button functionality as described in Table 2 at the back of this document Setting up the DASHe2 from a PC Software Installation Place the supplied DASH2 CD into the CD drive of your machine Please note that in order to communicated from a PC to the DASH2 unit the PC will require an RS232 port Many modern laptops no longer have this port but USB to RS232 converters are readily available from computer component stockists The software should now automatically install If it does not please open the CD in the File Manager and click on setup exe This will start the installation process Please follow the on screen instructions At the prompt for which version of the software select the Potenza version When asked for a password please enter potenza Starting the DASH Configuration Tool Quick Start Go to the program file menu Start on Windows operating systems prior to Vista and click on All Programs Select Race Technology v7 from the menu and then configuration followed by DASH2 if a with ecu variables option exists please select this one This will open the DASH2 configuration tool E DASH2 Configuration Tool 1 0 87 Titi ii bi LHI aooo 0000 JU D amp SH2 Analog 1 DAI Scaling Filtering u 1x Maximum rate of change in scaled units per sample jo Generate an equation from a table 0 off Number of samples p Usea standard sens
5. by default each time you start a new run There is a mode on the DASH2 where the lap and sector times can be edited and kept from one run to the next This is very useful for pacing functions where a comparison against a known lap time is required The lap timing is split into two sections sector times and lap times The lap times are the times from the beginning of the lap to the given marker whereas the sector times are the total times for the given sector The two sets of timing data are set up independently Thus it is possible to monitor performance against fixed sector times whilst still having a constantly updated best lap time or vice versa Copying current lap sector times to memory After completing a run the lap and sector times from the run can be stored to use as a reference for the next run To do this go to Lap timing followed by Store sector times to store sector times or Store marker times to store lap times In each case press the SELECT button to save the current sector or lap times to the DASH2 memory Once the times have been stored to memory they can be used for subsequent runs or edited Editing target lap sector times To edit the target sector or lap times go to Lap timing followed by Edit sector times or Edit marker times and press SELECT to edit the stored target sector and lap times 21 respectively NOTE Target sector and lap times must first be stored to the DASH2 memo
6. logger has a GPS lock at the start of the run otherwise it will just pick up the first file found If there are no files on the compact flash card then it will write to the file MARKERO1 LAP if MARKERO1 LAP already exists it will go to MARKERO2 LAP and so on Lap timing operation With a LAP marker file present on the compact flash card lap timing operation will start automatically when you pass the start finish marker for the first time with the data logger on with GPS lock and logging data After this when you complete each sector the time will be compared with the time to that point on your fastest lap and your fastest time for that particular sector These times will be displayed on the DASH2 in the following format SECT LAP LAP 0 00 21 0 30 62 0 00 19 The first value is the sector time information showing that at this marker the time was 0 21s slower than the best time for that sector The second value is the time to this point on the lap showing that it has taken 30 62s The third value is the difference between current and the best time to this point on the lap The driver is 0 19s slower than on the best lap in this case 20 The sector timing will continue in this way for each sector marker passed until the end of the lap at which time the lap time and sector times will be compared against the previous best ones the best will be updated as required unless stored lap or marker times are being used The vehicle spee
7. to the DASH2 The DASH2 stores all configuration settings so there is no need to repeat this procedure each time the unit is powered up unless making changes to the existing configuration 12 Operating the DASHe2 During normal operation the DASH2 will display the selected information to the driver and monitor all inputs for alarm conditions In vehicle control of the DASH2 functions is via a logical menu structure and four buttons MENU SELECT UP and DOWN These allow the user to alter displayed units switch between data screens change button functions and set or configure many other options When in menu system display mode the actual function of the MENU SELECT UP DOWN buttons is fixed but their function during normal display mode can be programmed for example to provide shortcuts to frequently used features The MENU button is used to switch between normal display and menu system display This is the only button whose function cannot be changed Figure 4 illustrates the structure of the menu system The following sections describe the details and operation of each function Menu structure Press MENU to enter menu system display mode Using the UP DOWN buttons you can then scroll through the following options Predictive lap timing on off Logging status display on off Odometer and trip meter display on off Edit button functions Reset value 1 Reset value 2 Speedo RPM and gear LED Brightness Lap times Warning time
8. MAXIMUM INPUT VOLTAGE APPLIED TO THESE CHANNELS MUST_NOT EXCEED 15V The input voltages will need scaling to display the correct readings for the physical parameters being measured This calibration is carried out using the DASH2 configuration software Further details are included in the Online Help System 26 Appendix II Connection to a Race Technology data logger The DASH2 can be connected to the serial output port of a Race Technology DL1 or DL2 data logger AX22 performance meter or SPEEDBOX speed sensor By connecting the unit in this way many more data channels are available compared to when used in stand alone configuration For example when connected to a DL1 data logger some of the additional information that is available for real time display is Battery voltage 8 additional analogue inputs 4 frequency inputs Vehicle position and position accuracy Vehicle speed and speed accuracy Vehicle altitude and altitude accuracy Vehicle heading Lap and sector timing The DASH2 is connected to the output from a DL1 DL2 AX22 or SPEEDBOX using the serial connector provided on the Connector2 section of the DASH2 wiring harness This connection is optional and does not affect the stand alone functions of the DASH2 When connected to the vehicle harness and to a data logger the DASH2 has a choice of which vehicle speed and engine speed inputs to use 2
9. Send Configuration Serial This will configure the all instrumentation apart from the vehicle speed Of course you can configure the DASH2 to your own settings via the configuration tool This is described further in the section titled Setting Bespoke Configurations and via the online help Vehicle Speed Calibration The vehicle speed calibration is undertaken via the menu within the DASH2 Power the DASH2 and press the menu button At the bottom of the screen the DASH2 will display Predictive on off Menu options can be scrolled through using the up or down button until the screen displays Speedo and RPM Press the select button screen displays Pulses per Mile after first press The vehicle speed can now be calibrated The table below provides the typical settings based on the number of pickups per revolution and the wheel size It is recommended that some form of calibration is undertaken against a GPS receiver based speed measurement or similar to ensure the speed reading is correct NOTE Although inspection has shown 6 pick up points for most vehicles speed sensor at rear of vehicle off drive shaft bolts in practice the system may only detect 4 of these Hence the requirement for calibration on a case by case basis Wheel Size Revolutions mile Number of pickups DASH2 setting 195 50 R15 205 50 R15 215 50 R15 Table 1 Wheel Sizes and Revolutions Mile N O 205 60 R13 0921 N 9 E N O N
10. ammable buttons can be used to select which screen to display This enables toggling through the five screens of data To set up a button to do this see the section Programming soft buttons and assign the Next screen or Previous screen functions as shown in Figure 4 When changing between screens the screen number is briefly indicated at the bottom of the display Starting and stopping a data logger from the DASH2 When suitably connected and configured the DASH2 can be used to start and stop data recording on an attached logger To enable this feature set up one of the buttons on the DASH2 to the Trigger logger function as described in the Programming soft buttons section The data logger must be configured with GSM mode and enabled to make use of this feature Without setting the GSM mode option on the data logger the commands from the DASH2 will be ignored Whenever the Trigger logger button is pressed a command will be sent to the data logger to start or stop logging The logger must be powered up and have a correctly formatted card inserted in order to commence logging Programming soft buttons The UP DOWN and SELECT buttons can be programmed to perform many different shortcut functions in normal display mode these buttons can also be combined with the MENU button to provide a further three soft buttons if required This does not change the function of the buttons from their standard purpose in
11. an use analogue channel 1 as in input to show which gear is selected To set the DASH2 up for gear indication set the Ana Gears option to On next you will be asked how many gears are present Here enter the number of forward gears The unit will automatically add on for reverse and neutral After setting the number of gears the display will change to show the current gear being edited STORE which is the stored reading for the current gear and NEW which is the current reading on the analogue input To set up a particular gear use the UP and DOWN buttons to select the required gear and then press the SELECT button to store the reading The value from the NEW window will now appear in the STORE window showing that the upgrade has been completed When you have finished setting up the gears press the MENU button to exit and store the readings Please note that the DASH2 rounds off to the nearest Volt For example if gear 1 is set to 3v and gear 2 is set to 4v and voltage reading between 2 51 and 3 50 will be gear 1 Similarly any reading between 3 51v and 4 50v will be gear 2 17 Odometer and trip meter The DASH2 features a non resettable odometer as well as a resettable trip counter These counters are both driven from the internal wheel speed input i e from vehicle sensors connected directly to the DASH2 As such if the wheel speed input is not used as might be the case if the DASH2 is connected only to a data lo
12. d So for a 195 50 R15 tyre with 6 pickup points the setting will be 919 multiplied by 6 5514 For a given tyre the setting will always be a multiple of the appropriate revolutions mile figure Your DASH2 is now configured and ready for use 11 Setting Bespoke Configurations Five user configurable screens are available each displaying three sensor input channels enabling up to fifteen variables to be viewed in total All data channels can also be simultaneously monitored for alarm conditions As well as selecting which data is viewed and setting the alarm limits the configuration software is also used to set the scaling on each input channel and to set up the RPM display options and gear indicator calculations The DASH2 is supplied with a default configuration suitable for many typical applications particularly if external analogue sensors are not in use This will allow display of all the basic features after connection to the vehicle wiring harness as described above To make custom configuration changes full operating instructions for the configuration software are available from the Online Help System which is also included on the CD provided with the DASH2 Simply follow the path Software Configuration and reflash Configuring display products Uploading configuration data to the DASH2 Once changes have been made with the configuration program the new settings require uploading to the DASH2 This can be done either by a d
13. d display will temporarily be replaced with the number of laps completed each time a lap marker is passed The lap counter will be reset every time that data logging is stopped or started on the data logger Predictive lap times With predictive lap timing enabled instead of the lap times being shown as the time up to that point in the lap the lap time is extrapolated to estimate the lap time if the rest of the lap was covered at the same pace as the fastest lap For example if the best lap time was previously 2 45 23 after passing the first sector marker the DASH2 will display SECT LAP LAP 0 00 21 2 45 42 0 00 19 The first value is again the difference between the time for the sector just completed and the best time for that sector The second value is the predicted lap time if the remainder of the lap is covered at the same pace as the fastest lap and the third value is the resulting difference between the predicted current lap time and the fastest lap time Then after passing the second sector marker the following screen could be displayed The first figure indicates that the second sector was covered 1 00s faster than the previous fastest time for that sector The second figure is the update predicted lap time and the third figure is the difference between this predicted lap time and the current fastest lap time SECT LAP LAP 0 01 00 2 44 42 0 00 81 Using target marker and sector times The best lap and sector times will be reset
14. de In the case of speedo and RPM settings and LED brightness press SELECT to access these items from the main menu then use the UP DOWN buttons to configure the setting for each item and the SELECT button to save each setting and move onto the next item on that sub menu When the last item on the sub menu is reached pressing SELECT will return the DASH2 to the normal display mode The normal display mode may also be reached at any time by pressing MENU Logging status display The status of an attached logger can be displayed on the DASH2 with a tick mark in the top right hand corner as shown in Figure 1 It is also possible to set the left hand shift light as a secondary more highly visible logger status indicator This is selected using the Status display option item 2 in the DASH2 menu system see Figure 4 When this mode is enabled the left most shift light operates as a logging status indicator The remaining five shift lights operate as normal In the top left corner of the display see Figure 1 the DASH2 also has a binary symbol to indicate that serial communications are being received when the unit is used with a Race Technology data logger or other device such as a PC Changing displayed information There are five user configurable screens of data that can be displayed on the DASH2 The data to display on each screen is selected using the DASH2 configuration program on the PC Once the screens are configured the progr
15. different sources Either from vehicle sensors wired directly to the DASH2 inputs termed internal or DASH2 inputs or via the output from an external data logger termed RS232 inputs If the DASH2 is always used with a data logger it is better to configure the unit to use the RPM output from the data logger so that a high level RPM input can be used The vehicle speed output from the data logger would also give a more accurate input to the DASH2 but would only be present when the GPS signal is valid The odometer and trip counter only use the pulse input from the internal vehicle sensor so if the DASH2 is set up to use only the external speed input the odometer will not function For road legal applications the DASH2 must be used with a wheel speed input to measure vehicle speed and enable operation of the odometer and trip meter 16 Configuring the DASH2 to read both input sources for RPM or vehicle speed simultaneously should be avoided This can lead to information on the screen becoming unstable due to conflicting data being read from the two sources The RPM and vehicle speed sources are selected from main menu item 6 Speedo and RPM followed by selecting yes no for RS232 RPM DASH2 RPM and RS232 speed DASH2 speed where RS232 input refers to external data from a logger and DASH2 input refers to internal sources from vehicle sensors connected directly to the DASH2 Recomm
16. ds on dash loom Unplug any red orange connector sidelights and plug into red orange lead on dash loom Unplug 3 pin connector for water gauge and plug blue green dash loom lead into correspondingly coloured pin lead on 3 pin connector or green Please note it is very important to secure this connection with electrical tape or heat shrink as the 3 pin connectors do not have a good mechanical grip on the spade Unplug 3 pin connector for oil gauge and plug white brown dash loom lead into correspondingly coloured pin lead on 3 pin connector Unplug 3 pin connector for fuel gauge and plug green black dash loom lead into correspondingly coloured pin lead on 3 pin connector Unplug blue red lead from side of fog switch small spade connector and plug into blue red lead on dash loom You can now unplug all other leads from the original dash related to warning lights and gauges and remove the original dash We recommend these leads are secured either by tie wraps or electrical tape to a chassis member so they remain out of the way and do not rattle Any bare connectors should be insulated using electrical tape or heat shrink wrap Wiring of the dash is now complete Test the dash by turning on the ignition to ensure the dash powers Start the engine and the rev band should register The dash will not require a calibration download from a PC see Setting Up the DASH2 from a PC and the speedo will require calibration When fitting the
17. e 14 way electrical connections All three mounting holes should be used to prevent the unit from loosening under vibration In addition the use of a low strength thread locking compound is recommended for installations in a high vibration environment Mounting requires M4 fasteners with a thread engagement depth of 5mm Avoid over tightening the mounting screws to prevent thread damage Electrical installation The DASH2 is supplied with a wiring harness to connect directly to a standard Westfield harness The harness has two 14 way connectors to attach to the back of the DASH2 and a connector to the Westfield main loom modular loom For older standard looms an addition retro fit loom is provided which connects at one end to the modular loom connector and provides a number of spade connectors and 2 block connectors to plug into the standard vehicle loom When connecting to a standard loom we recommend that all connections are secured using electrical tape or a heat shrink sleeve Appendix I illustrates all connections on the rear of the DASH2 unit along with pin assignments Both looms are illustrated in Figure 2 overleaf The wiring up of the unit should only be entrusted to competent persons familiar with vehicle wiring installations as incorrect installation may result in both a risk of fire and damage to the DASH2 unit THE DASH2 WARRANTY DOES NOT COVER DAMAGE CAUSED BY INCORRECT CONNECTION Please ensure before connecting the dash that you
18. each marker has an approach direction associated with it as well as a position This means that if you have a hairpin with the two straight ways fairly close together and you added the track marker as you approach the hairpin then both the approach and exit paths will cross the track marker but the only time the software will log that you ve crossed the track marker is when you have passed the marker in the same direction as it was added If the addition of a desired track marker was missed it is possible to add a marker in after the first lap The data logger will calculate where the track marker is in comparison to the track you have drawn so far and if it is in between two other markers the hardware will split the sector into two but the track marker will be numbered as the next value 19 When you press the button to add a track marker a marker will be added at the next GPS sample point so it could be up to 0 2 seconds before the marker is actually added depending on the model and specification of data logger used If you are travelling slowly when the markers are added this will have no serious side effects If you are travelling quickly it is unlikely that you will be able to position the track markers with great accuracy This will not affect the timing between markers as these are in the same place on every lap but may affect the positioning of the markers with respect to circuit features Adding track markers from the Analysis So
19. endations 1 Without a data logger connected Use vehicle sensors to provide internal inputs to DASH2 RS232 inputs may be left enabled with no signal present on these channels they will cause no disruption to normal operation 2 Road car with data logger Internal wheel speed input otherwise there will be no odometer Internal RPM if available otherwise external through data logger 3 Race car with data logger External speed and RPM from data logger To set the correct scaling and configuration of the RPM input please refer to the DASH2 configuration software Changing the speed distance units Speed and distance are displayed in mph miles by default To change this to kph km select Speedo RPM Gear from the main menu then press the SELECT button until Speed units is displayed Use the UP DOWN buttons select the desired display units then press SELECT to save the new setting and return to normal display mode NOTE Although it is possible to select km or miles for the odometer and trip displays the calibration for the wheel speed input is always in pulses per mile If calibration data for external sensors is quoted in pulses per km this must be converted to pulses per mile to be entered as a calibration factor for the DASH2 in the configuration software Using an Internal input for Gear calculations As well as calculating which gear is currently in use from the ratio of the RPM and wheel speed inputs the DASH2 c
20. er Vehicle speed lap number indicator Max min indication Shift lights Gear indicator Serial input status 1 i 4 j I l Information and sensor sections Malfunction Alternator charge aes l indicator light warning Indicator warning Main beam Fog light warning warning Brake warning Figure 1 DASH2 general layout Odometer trip meter What s in the Box Please take a few moments to ensure that you have received all of the following components DASH2 display unit Wiring harness for DASH2 to Westfield modular loom Retro fit loom modular connector to Westfield standard loom Four selector buttons Serial extension cable to enable connection to a PC for configuration Instruction manual Comprehensive software CD Printed mounting template Carrying case with cut foam interior Installing the DASH2 Physical installation of the Display Unit The DASH2 must be securely mounted onto flat surface or suitable bracket When deciding on a mounting location it is important to position the viewing angle for the best display contrast The display can be clearly read over a wide range of incidence angles but it is most clearly viewed from an angle of approximately 10 20 above the display axis A printed template has been provided and should be used to check that there is sufficient space for mounting the unit There should also be room for drilling the clearance holes for the fixing screws and th
21. eteneiseciseccsveisanasencanetencitecanecteneneunisuncanetancinera 8 Setting Up the DASH2 froma PG a pean esieexiiet 10 SoftWare Instalati Asinara a aiaia 10 Starting the DASH2 Configuration Tool Quick Start rr 10 Uploading Westfield Standard Configurations rr 11 Vehicle Speed CaliDratiOl miiiirneririnerionen rudere aaao aaae aeria 11 Setting Bespoke COnfiQurations cscccsscseccsecseccseesecusnesecuseenscusneseceseeneceseentseseearsaseeates 12 Uploading configuration data to the DASH2 iii 12 Directly from the Perni iii 12 TArough a data IOOGEE irora EEEE EEA EEEN EEE ETETEAREN VETERE TOTEE iNi 12 Operatno CNG DASH 2 Ro ala 13 MEMUPSEMUIGTUING sececcsereserccecsconsnecicnseoesscenesedisenseecinesion tices icecesensercseensnecicesecesicevesesiessies 13 OG GIG Stat s GIS DIAY sciteralais as ice siehaieiecaleivdalsttalvintaainialvittalsdulaledau via e a iE 15 Changing displayed information 15 Starting and stopping a data logger from the DASH2 rr 15 Programming Soft DUON S rerien EEE NAER 15 Reviewing maximum and minimum data valUues i 16 Resetting a monitored value to zero for change MeasuremEnt 16 Setting up internal external RPM and vehicle speed readingsS a 16 Changing the speed distance UNItS ii 17 Using an Internal input for Gear calculations iii 17 Odometer and trip Mete carceraria a E AA
22. ftware Track marker files can also be written to the Compact Flash card The file names MUST be in 8 3 format meaning that the entire file name must be in UPPERCASE letters and it must have no more than 8 characters before the decimal point The file extension MUST be LAP and must also be in UPPERCASE letters If the files are not named in this way the data logger will not recognise them To generate a LAP file from raw data please refer to the section on Adding Track Markers in the Analysis Software documentation or On line Help System The resulting LAP file should be saved to compact flash card for transfer to the data logger The LAP file must be placed in the root directory of the Compact Flash card It is advisable not to have multiple LAP files with similar marker locations in this directory to avoid the possibility of the data logger selecting the wrong lap marker file if multiple LAP files are present Using lap marker files with the DASHe2 The data logger stores the lap markers in a LAP file in the root directory of the compact flash card At the start of a run the data logger will check its current position against the reference positions in any LAP files on the memory card As such you can have 10 different LAP files on the card and so long as they were not started within about 15km of each other the data logger will pick up the correct one for the current location For this reason it is very important that the data
23. gger for vehicle speed data the odometer will not function For the odometer to function correctly the number of pulses per mile must be set Change this using Speedo and RPM followed by Pulses per mile from the sub menu Use the UP DOWN buttons to toggle to the desire value then press SELECT to save the new setting To calculate the number of pulses per mile measure on the ground the distance travelled during one complete wheel rotation in metres or inches and use one of the following formulae Distance in meters Pulses per mile 1609 rolling circumference of wheel Distance in inches Pulses per mile 63360 rolling circumference of wheel NOTE These formulae assume 1 output pulse per wheel rotation The DASH2 configuration software also allows for calibration with wheel speed sensors giving more than one pulse per revolution as described in the Online Help System To calculate the number of pulses per mile in the case simply multiply the result of the equations overleaf by the number of pulses per wheel rotation It is also possible to hide both the odometer and trip meter for example in racing applications when this information is not relevant To hide the odometer and trip meter select Odometer from the DASH2 menu system as shown in Figure 4 and use the SELECT UP DOWN buttons to change the setting Resetting the trip meter To reset the trip meter one of the programmable buttons UP DOWN or SELECT must be
24. hange to show the minimum values A third press of the button will reset all Max Min values Resetting a monitored value to zero for change measurement Whilst most values displayed on the DASH2 will show an absolute reading such as the water temperature or quantity of fuel in the tank there are times when it would be useful to monitor changes in value such as how much fuel has been used to cover a certain distance To achieve this the DASH2 can be configured to reset a channel to zero on a single button press There are two steps in this process Firstly selecting which channel to reset and then secondly setting one of the buttons to perform the reset function To select which channel to reset go to Reset value 1 or Reset value 2 Press SELECT then use the UP DOWN buttons to scroll through the list of available channels until you see the one you wish to reset Press SELECT to choose this channel and return to normal display mode To set up a button to perform the reset function see Programming soft buttons and set the button to either Reset value 1 or Reset value 2 Whenever this button is pressed it will reset the displayed value of the selected channel to zero To return the channel to reading its normal value change to another channel on the reset button and or change the button function Setting up internal external RPM and vehicle speed readings The DASH2 can display RPM and vehicle speed data from two
25. ines provide a step by step guide to replacing a standard Westfield SE dash VDO instruments with the DASH2 Numbers on the images correspond with the step numbers 1 Remove top trim from scuttle normally held down with velcro 2 Remove steering wheel remove padding and then centre bolt 22mm socket er dl 3 Remove dash retaining bolts 3mm allen key 4 Pull dash away from scuttle revealing wiring If the vehicle has a modular loom the dash electrical connection is made by two block connectors The block connector leading to the instruments should be unplugged and the dash loom plugged in its place For a standard Westfield loom please follow the following steps using the retro fit loom 5 Remove block connectors from tacho and speedo and plug in corresponding connectors from loom match pin layou 3 pin and 4 pin respectively i pr r Fi n i r 10 1 pa 12 13 14 15 16 17 Unplug blue white lead to high beam light and plug into blue white lead on dash loom Unplug black white lead to brake warning light and plug into black white lead on dash loom Unplug brown yellow lead to ignition warning light and plug into brown yellow lead on dash loom Note for 1600 Sigma vehicles this light does not come on at ignition on if a smart alternator is fitted Unplug green red and green white leads to indicator dash lights and plug into corresponding green red and green white lea
26. ing The fog light warning is activated when 12v is applied to Connector1 Pin 14 as shown in Table 1 This is usually achieved by connecting to the vehicle wiring loom between the fog light switch and the fog light itself Alternator charge warning This warning lamp is illuminated when alternator output is low and the vehicle battery is not being charged This will be the case when the ignition is turned on but the engine is not running or if there is an alternator fault To make use of this feature Connector 1 Pin 10 should normally be connected to the field alternator warning terminal on the alternator via the relevant cable in the vehicle wiring harness Sidelight input The sidelight input is used to alter the brightness of the shift lights and indicator hazard warning lights This requires Connector2 Pin 1 as shown in Table 1 to be connected directly into the vehicle wiring loom between the sidelight switch and the sidelights themselves When the input to this pin is at Ov the shift and indicator hazard warning lights will be bright but when the input to this pin is at 12v the shift and indicator hazard warning lights will be dimmed slightly The brightness of the shift lights can also be adjusted independently as described on Page 18 Wheel speed input Wheel speed input data are used by the DASH2 for the vehicle speed odometer and trip recorder displays and for gear indicator calculations This input requires a 5v or 12v squa
27. irect serial connection between the PC and the DASH2 or through connection to a DL1 DL2 or AX22 data logger Directly from the PL This requires connection of the DASH2 serial connector and the serial port on the PC using the serial extension cable provided A USB to serial adaptor will also be required if the PC does not have a serial port Full instructions for uploading the new configuration to the DASH2 are provided in the Online Help System by following the path Software Configuration and reflash Configuring display products Through a data logger After completing all changes in the configuration software click on the save button The file with the new configuration settings must be saved as DASH2 DAT on to a compact flash memory card in to the root directory The compact flash card should then be inserted into the data logger with the DASH2 connected The compact flash card may be inserted in to the data logger with the unit and DASH2 powered up When uploading configuration changes it is recommended that the new DASH2 DAT is the only file on the compact flash card The DASH2 DAT file will be automatically read by the data logger and the new configuration settings will be uploaded to the DASH2 During configuration upload the display will freeze for a few seconds before displaying the new settings when the configuration upload is complete To ensure all new configuration settings are displayed it is recommended to cycle the power supply
28. menu display mode To change a button function simply select Edit button functions using the UP DOWN buttons main menu item 3 then press SELECT You will then be asked to press the button you wish to 15 change the function of Press either SELECT UP or DOWN to access the three extra soft buttons press and hold MENU without releasing it press SELECT UP or DOWN The display will change to show which button is selected and the current function assigned to that button The UP and DOWN buttons can then be used to select any one of 12 functions to assign to this button as shown in the sub sub menu in Figure 4 Press SELECT to confirm the button function and return to the main menu Reviewing maximum and minimum data values The DASH2 can store and display maximum and minimum values for each of its input channels These values can be reviewed by setting one of the buttons to the Show max min function as shown in the sub sub menu in Figure 4 Refer to Programming soft buttons and set the button function to Show max min Whenever this button is pressed it will temporarily replace the current three displayed channels with their maximum values This display will be held for around five seconds during this time moving on to another display screen will reset the timer thus enabling you to scroll through all display screens and view all maximum values If the max min button is pressed again during this time the screen will c
29. ne Help System PLEASE DO NOT ATTEMPT TO REFLASH YOUR DASH2 UNLESS YOU ARE ABSOLUTELY CONFIDENT IN THE REQUIRED PROCEDURE AND HAVE READ THE REFLASHING INSTRUCTIONS IN FULL 22 Appendix DASH Direct Pinout 12V and GND Analogue input 2 connections 4 connections Vehicle harness 8 connections 12V and GND External control buttons 2 connections 5 connections i aga Vehicle harness Serial Input 1 connection connector a oV reference output 1 connection Figure 2 DASH2 electrical connections 23 _2 EngineSpeedin 12v squarewave White 3 JE ety Red G Brakewaming Ovtoactivate Green white 3 AnalogueIn3 tv Pink E Ground Black Main beam warning 12v to activate N Wheel speed in 5 12v o Analogue In 1 0 15v OP Alt wiring field drive Ov to activate R ow WIN mi 1q im 09 0453 90 14 MIL light Ov to activate Yellow white S Analogue In 2 0 15v IR Indicator 12v to activate UU Fog light warning 12v to activate A Sidelights 12v when on RES Switch common UE 12V G RS232 EA Select button Ground No connection Down button 5V reference output N Oo Pp RS232 R zoe Binder 423 Series Male Bulkhead m O_ O _ T D O j O oO CC C O m gt c 10 16v RS232 White Switch to common LG Switch to common 50mA max 09 0453 90 14 e e e e O RS232 Black screen RS232 Red S
30. or to average over 1 100 1 olf Enter an equation manually Other Channel Name DAI Alarm limits High alarm value D Low alarm value p becchi Enter 0 for the high and low value to disable alarm Sio spazza 1 Native input unit v Comments This isthe analogue channel attached directly to the DASHZ rear connector default equation 1 x Le no scaling Serial Port 1 is Send Configuration Serial Save Configuration Import Configuration File Figure 3 DASH2 Configuration Tool 10 Uploading Westfield Standard Configurations Westfield provide standard configuration files for different Westfield instrumentation setups These are named according to the instruments used e g vdo dat smiths dat To install an appropriate file you must first download the file from the Westfield website Go to www westfield sportscars co uk and follow the link to support Select the DASH2 support page and you will find downloadable files for calibration If you have any problems downloading the file please contact the factory for support Once downloaded click on Import Configuration File on the Configuration Tool and select the relevant downloaded file Once the configuration is loaded it has to be transmitted to the DASH2 unit from the PC Connect the PC to the DASH2 via the supplied RS232 lead Select the appropriate Serial Port from the drop down menu on the bottom left of the screen Power the DASH2 and then click on
31. r Westfield has a standard loom For wiring to specialist models XI XTR Mega range Sport S it is t Only applicable if dash is not bought with Westfield DASH2board recommended that you visit the Westfield website for wiring support www westfield sportscars co uk support If your model is not covered contact the Westfield factory to discuss installation NOTE All connections to the DASH2 should be made with the power supply disconnected The ends of any unused cables on the DASH2 flying lead loom should either be insulated with the cables coiled and secured in a safe manner or trimmed back and removed altogether NOTE The wiring on the retro fit lead loom is colour coded to match the wiring colour on the appropriate connector on the main loom Some models have modifications to the standard loom which need to be considered when wiring in the dash RETRO FIT LOOM Connection to i modular loom RS232 communications lead to PC data __ logger i Power for data logger DASH2 connectors Menu switches Figure 2 Wiring to standard loom DASH2 Loom and Retro Fit Loom Switch inputs The four buttons provided should be connected to the loom to allow in vehicle control of many functions and display options These buttons are required to set certain display functions and options The appropriate lead colours for the switch connections are indicated in Figure 2 above Step buy Step Installation Guide This guidel
32. re wave signal applied to Connector1 Pin 8 as listed in Table 2 This output format is normally provided by a standard vehicle wheel speed sensor There is no conditioning on this input for a VRS sensor The input has an internal pull down to ground so the input can be activated by a simple switch to either 5 or 12v The procedure for configuring this input to the correct pulse rate per distance travelled is described on Page 18 25 Engine speed input The engine speed input can be used with the DASH2 in stand alone mode or with a data logger connected to give an engine RPM input reading This information is also used in the gear indicator calculation This channel requires a 5v or 12v square wave input applied to Connector1 Pin 2 as show in Table 1 IT MUST NOT BE CONNECTED DIRECTLY TO THE IGNITION COIL OR AN INDUCTIVE PICKUP FROM THE HIGH TENSION SIDE OF THE IGNITION SYSTEM This channel should normally be connected to the engine speed output channel from the engine management ECU Analogue inputs The DASH2 is provided with four fully configured analogue input channels of its own These are in addition to any analogue inputs provided by connection to a data logger These channels may typically be used to monitor variables such as fuel level water temperature and oil pressure via existing sensors The sensor outputs should be connected to the DASH2 analogue input channels on Connectori Pins 1 5 9 and 12 as listed in Table 1 THE
33. ry before they are available for editing The screen will now show the marker or sector times for each sector Use the UP and DOWN buttons to select the sector time to edit and then press the SELECT button The UP and DOWN buttons can now be used to change the target time Pressing and holding the buttons will cause the times to change faster When the required time is displayed press the SELECT button to save the new time and return to the previous screen to enable selection of another sector for editing When all times are set press the MENU button to exit and return to display mode Using target marker sector times To use the target sector times and lap times go to Lap timing followed by Use stored sectors or Use stored markers Press SELECT then use the UP and DOWN button to set the option to yes and SELECT to save and exit For each run lap and sector times will then be compared with the target values stored in the DASH2 memory Re flashing the DASH2 The DASH2 firmware can be re flashed to take advantage of any software changes or new features introduced New firmware upgrades will be introduced from time to time as new features are implemented Firmware files will be available for download and installation from the Westfield Sportcars website Re flashing can be done through a serial connection to a PC Full details of how to perform the re flashing process are provided with all firmware updates or from the Onli
34. s 13 Main menu items Sub menu items Predictive on off Status display on off Odometer on off Edit button functions Press button to change function dl UP DOWN SELECT MENU UP DOWN SELECT Reset value 1 Reset value 2 Speedo and RPM Pulses per mile R5242 RPM yes no DASH2 RPM yes no RS232 Speed yes no DASH Speed yes no Speed units speed and distance mph kph LED brightness High brightness Low Brightness Store marker times time S Figure 4 Menu system structure Ana gears I on ott Sub sub menu items Disabled Next screen Previous screen Trigger logger Reset value 1 Reset value 2 Add marker Trip reset Show max min Reset lap times Reset lap count Num gears Config gears T To edit function settings display the function in question using the UP DOWN buttons and press SELECT Use UP DOWN to change the function settings then SELECT to save the new setting and return the DASH2 to its normal display mode Several menu items also have sub menus as shown in Figure 4 In the case of the lap timing functions first press SELECT to access the lap timing functions from the top level menu then use the UP DOWN buttons to display the required sub menu item and press SELECT again to open the settings followed by UP DOWN to change the settings and SELECT to save the new settings and return to normal display mo
35. toring sensors and sending this information to the DASH2 no lap or sector times will be displayed The lap timing functions use GPS data from the data logger so can only function correctly when the logger has a valid GPS lock Lap timing functions use GPS coordinates as track markers to define sectors and laps These markers can be added either by setting up a button on the DASH2 to add a marker by using a dedicated button connected to the data logger or by adding them to data using the Analysis Software and saving the resulting lap file to the memory card for transfer to the data logger Each of these options is explained in detail below Adding track markers from the DASH or DLI DL 2 To use a DASH2 button to add markers refer to Programming soft buttons and programme one of the buttons to perform the Add marker function as illustrated in Figure 4 To use a DL1 DL2 switch connect a switch to the data logger as described in the documentation provided with the data logger itself When the data logger is in operation a track marker will be added each time the DASH2 or logger button is pressed When you wish to add track markers it is advisable to drive slowly around the circuit and press the add marker button each time you pass a point you wish to use as a track marker The first marker you add will ALWAYS be the LAP marker The markers you subsequently add will split the track up into sectors It should also be noted that
36. uttons can be used to edit the brightness to the desired level Then press SELECT to save the high brightness setting and move on to the low brightness setting Again use the UP and DOWN 18 buttons to set the desired brightness then press SELECT to save and return to normal display mode If the sidelight input is not connected the shift LEDs will remain at the high brightness setting at all times Setting warning and sector display times The duration for which warning messages and sector times are displayed on the screen can also be configured from the DASH2 menu system Enter menu display mode and use the UP DOWN buttons to display Warning times in the main menu and press SELECT Then use the UP DOWN buttons to select the desired warning duration press SELECT to save the new setting then use the UP DOWN buttons to set the duration of the sector time display and press SELECT again to save this setting and return to normal display mode The shift light second from the left will flash when the warnings are displayed Lap timing on the DASH2 To use the DASH2 lap timing functions the unit must be connected to a Race Technology DL1 or DL2 data logger The data logger monitors when the vehicle has passed a track marker and sends the lap or sector timing information to the DASH2 which displays the data and stores best lap and sector times The lap timing functions only operate when the data logger is logging data If the logger is just moni
37. witch to common Switch to common Connector 2 Binder 423 Series Male Bulkhead RS232 S No connection Up button Menu button Table 2 Connector pin assignments Figure 4 Connector orientation NOTE Please take special care to ensure correct orientation relative to connector keyway when identifying connector pins 24 DASHe Connection Notes Indicators hazard warning lights The warning light for the indicators and hazard lights is activated by applying 12v to Connector1 pin 13 as identified in Table 2 These should normally be connected directly to the vehicle wiring loom between the indicator switch and the indicator itself The brightness of the LEDs will vary depending on the status of the sidelight input This feature is included to dim the indicator warning lights at night to avoid dazzling the driver yet allow them to be clearly visible during daylight hours Main beam warning light The main beam warning light is activated when 12v is applied to Connectori Pin 7 as shown in Table 2 This is usually achieved by connecting to the vehicle wiring loom between the headlight switch and the main beam bulb s Brake warning light The brake warning light is activated when Ov is applied to Connector1 Pin 11 as shown in Table 1 This is usually achieved by connecting directly to the handbrake warning switch and or low brake fluid warning switch at the appropriate point in the vehicle wiring harness Fog light warn
Download Pdf Manuals
Related Search