User Manual
Contents
1. m Um dos unde UN 3 9 3 O DIMENSIONS CHAPTER 4 DIP SWITCH SETUP entities Chapter 1 RC303 304 GE XX Copper to Fiber Media Converter Introduction 1 1 Article Description RC3034 GE S1 R145 SC APC RC303 4 GE S1 Remote managed 1000Mbps single mode single strand dual wavelength 0 25km 1 2 Product Specifications a ab Supported E Transmit Receiving Receiving p Article Wavelength es Link Attenuation Interface Power Sensitivity Saturation Number nm Distance dB km dBmW dBmW dBmW km RC303 GE S1 SC APC RJ45 1310 5 0 25 0 0 25 0 5 RC304 GE S1 SC APC RJ45 1550 5 0 25 0 0 25 0 5 1 3 Explanation for the Front Panel and Indicators 1 3 1 Indicators on the front panel Link ETH po ETH TX is s TX m S m Full Power nm ETH RX Duplex Mode Figure 1 The front panel of RC303 304 GE XX The definitions of indicators are as follows Interface Indicator Name Indicator Definition Optical Optical Link LNK ON Optical link works in good condition Interface OFF Optical link disconnected Ethernet Link LNK ON Ethernet link works in good condition OFF Ethernet link disconnected Ethernet Ethernet Full Duplex Mode FDX ON Ethernet por2. RC303 304 GE XX Copper to Fiber Media Converter User Manual m Beijing Raisecom Science amp Technology Co Ltd CONTENTS CHAPTER 1 RC303 304 GE XX COPPER TO FIBER MEDIA CONVERTER INTRODUCTION rt ttrtttnnntttnnnettnnntt 1 1 ARTICLE DESCRIPTION ha deen e PEDE EXER ERN e EAE AN EUR E YR E OLI E ded 1 2 PRODUCT SPECIFICATIONS ote Deren ue sake VERE RR ERE SE RN TIS ERR VES 1 3 EXPLANATION FOR THE FRONT PANEL AND INDICATORS cccsssccceessseceeesseeccsssseeeessssecceseeecessssecceessteceeeseeees LoT Indicators onthe front panels a ye RR RR NR ER ER EE RE KEIN TEE CHAPTER 2 CONNECTION CONFIGURATION 2 1 MEDIA CONVERTER INTERCONNECTION scscscsssssssssssssessssssssssssssssssesesssesescscscscscscscscscscscscscsesessssssssssssssseeseeeees 2 2 CONNECTION WITH OTHER EQUIPMENT AT RJ45 PORT tenete 2 3 DUPLEX MODE CONFIGURATION RJ45 PORT ccccscscsssssssssssssssssssssssssssesesesesescscscscscscscscscsssssssssssssssssssssseseseses 2 4 CONNECTION WITH OTHER EQUIPMENT AT OPTICAL PORT ssssssssssssssscecscscscscscscsescscscscscsesesesesesesessseseeneeeees CHAPTER 3 INSTALLATION AND 3 1 MATCHING OPTICAL FIBER WITH THE MEDIA CONVERTER eese nennen nne nne nensis SA DYPES OF BIBERSOPTIG GABLE M eet ioi ed Ms LN Un oL E UU EST E UR d 3S ETHERNET PORTS i om dee SA AMBIENCE
3. anagement system Users are not allowed to change the factory default setup 3 The factory default setup of SW2 Fault Pass Through function disabled BROADBAND To RAISECOM Copyright Declaration Beijing Raisecom Science amp Technology Co Ltd is the owner of this manual booklet The part or whole of this manual is not allowed to reproduce without Raisecom s permission All rights Reserved
4. t works in full duplex mode Port OFF Ethernet port works in half duplex mode Ethernet Transmit Link TX Flashing Transmitting data at the Ethernet port Ethernet Receive Link RX Flashing Receiving data at the Ethernet port Power Power Supply Indicator PWR ON Power supply works in good condition Supply OFF Power supply disconnected Chapter 2 Connection Configuration 2 1 Media Converter Interconnection When interconnecting RC303 304 GE media converters it is required to comply with the specific connection article numbers according to the following table Otherwise the link will not be established or abnormal data transmission will occur Host Site Remote Site RC304 GE S 1 RC303 GE SI 2 2 Connection with Other Equipment at RJ45 Port RC303 304 GE XX copper to fiber media converter supports MDI MDIX auto sensing function Media Converter Other Equipment Connection Type at Ethernet Port RC303 304 GE Switch Straight through or Crossover RC303 304 GE Hub Straight through or Crossover RC303 304 GE Router Straight through or Crossover RC303 304 GE Network Interface Card Straight through or Crossover 2 3 Duplex Mode Configuration RJ45 Port The RJ45 port Ethernet port of RC303 304 GE XX media converter works at the data rate of 1000Mbps When connected with other network equipment the Ethernet port of that equipment shall be configured to Full Duplex Mode Th
5. us normal data transmission in Ethernet link can be ensured 2 4 Connection with Other Equipment at Optical Port When connecting RC303 304 GE media converter with other equipment at optical port the following conditions shall be satisfied 1 Same wavelength 2 Same bit rate 1000Mbps 3 Matched optical power Chapter 3 Installation and Preparation 3 1 Matching Optical Fiber with the Media Converter RC303 304 GE XX shall adopt the single mode fiber and the connector shall be SC APC 3 2 Types of Fiber optic Cable The type of the cable for single mode fiber port 9 125um single mode fiber 3 3 Ethernet Port Please use the Cat 5 twisted pair to connect the media converter Please note that the twisted pair cable shall not be longer than 100 meters For connection configuration please refer to 2 2 Connection with Other Equipment at RJ45 Port Chapter 2 3 4 Ambience Working temperature 20 60 C Humidity 5 90 non condensing 3 5 Power Supply Single Slot Chassis 110V 60Hz AC 220V 50Hz AC or 48V DC 3 6 Dimensions Single slot chassis 158 width x 40 height x 120 depth mm Chapter 4 Dip switch Setup 1 The configuration of RC303 304 GE media converter is performed by a 2 bit dip switch SW2 The configuration details are as follows SW2 1 Fault Pass Through Function Setup OFF Disabled ON Enabled 2 The other dip switch SW1 on the media converter module is only used for the network m
Download Pdf Manuals
Related Search